One of Fireworks firmware, named as 'AudioFire9', seems to transmit
packets with wrong value of dbs. It's always 0x11 but actual size of
data block is different.
This commit adds a flag for this quirk and some codes to calculate
correct size.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks has a quirk for the value of dbc field in transmitted packets.
For Fireworks, dbc means the end of events in current packet. This is out
of specification.
For example, AudioFire4:
CIP0 CIP1 Payload
01070092 90FFFFFF 02
0107009A 9001E17B 3A <-
010700A2 9001F6E5 3A
010700A2 90FFFFFF 02
010700AA 9001104F 3A <-
010700B2 900125B9 3A
010700BA 90013B23 3A
010700BA 90FFFFFF 02
010700C2 9001548E 3A <-
010700CA 900169F8 3A
010700CA 90FFFFFF 02
010700D2 90018362 3A <-
010700DA 900198CC 3A
According to IEC 61883-1/6, a packet following to empty packet has the same
value for its dbc. But for Fireworks, it's incremented and empty packet has
the same value as previous packet in dbc field.
This commit adds a flag for Fireworks and some codes to checking dbc continuity.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks has a quirk to transmit empty packets with TAG0. This commit
adds handling this quirk for full duplex stream synchronization.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks manages connections by CMP and can transmit/receive AMDTP streams
with a few quirks. This commit adds functionality to start/stop the streams.
Major Fireworks products don't support 'SYT-Match' clock source mode, except
for AudioFire12/8(till 2009 July) with firmware version 1.0. Already in
previous commit, this driver don't support such old firmwares. So this commit
adds support for non 'SYT-Match' clock source modes.
I note that this driver has a short gap for MIDI streams when starting PCM
stream. When AMDTP streams are running only for MIDI data and PCM data is
going to be joined at different sampling rate, then AMDTP streams are
stopped once and started again after changing sampling rate.
Unfortunately, Fireworks is not fully compliant to IEC 61883-1/6. Some commits
following to this commit add these quirks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks uses own command and response. This commit adds functionality to
transact and adds some commands required for sound card instance and kernel
streaming.
There are two ways to deliver substance of this transaction:
1.AV/C vendor dependent command for command/response
2.Async transaction to specific addresses for command/response
By way 1, I confirm AudioFire12 cannot correctly response to some commands with
firmware version 5.0 or later. This is also confirmed by FFADO. So this driver
implement way 2.
The address for response gives an issue. When this driver allocate own callback
function into the address, then no one can allocate its own callback function.
This situation is not good for applications in user-land. This issue is solved
in later commit.
I note there is a command to change the address for response if the device
supports. But this driver uses default value. So users should not execute this
command as long as hoping this driver works correctly.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for devices based on Fireworks. This driver
just creates/removes card instance according to callbacks.
Fireworks is a board module which Echo Audio produced. This module
consists of three chipsets:
- Communication chipset for IEEE1394 PHY/Link and IEC 61883-1/6
- DSP or/and FPGA for signal processing
- Flash Memory to store firmwares
Current supported devices:
- Mackie Onyx 400F/1200F
- Echo AudioFire12/8(until 2009 July)
- Echo AudioFire2/4/Pre8/8(since 2009 July)
- Echo Fireworks 8/HDMI
- Gibson Robot Interface pack/GoldTop
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds three commands, which may be used by some firewire device
drivers. These commands are defined in 'AV/C Digital Interface Command Set
General Specification Version 4.2 (2004006, 1394TA)'.
1. PLUG INFO command (clause 10.1)
2. INPUT PLUG SIGNAL FORMAT command (clause 10.10)
3. OUTPUT PLUG SIGNAL FORMAT command (clause 10.11)
By the command 1, the drivers can get the number of plugs for AV/C unit or
subunit.
By the command 2 and 3, the drivers can get/set sampling frequency.
The 'firewire-speakers' already uses INPUT PLUG SIGNAL FORMAT command to set
sampling rate. So this commit also affects the driver.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices based on BeBoB use this type of AV/C transaction.
'Deferred Transaction' is defined in 'AV/C Digital Interface Command Set
General Specification' and is used by targets to make a response deferred
during processing it.
If a target may not be able to complete a command within 100msec since
receiving the command, then the target shall return INTERIM response,
to which final response will follow later. CONTROL/NOTIFY commands are
allowed for deferred transaction.
In the specification, devices allow to send INTERIM response just one time.
But this commit allows to handle several INTERIM response with two reasons.
One reason is to simplify codes, and another reason is to prepare for
devices which is out of specification.
There is an issue. In the specification, the interval between INTERIM
response and final response is 'Unspecified interval'. The specification
depends on each subunit specification for this interval.
But we promise to finish this function for caller. In this reason, I use
FCP_TIMEOUT_MS for this interval. Currently it's 125msec. When we find
devices which needs more time for this interval, then let us add some codes
to apply more interval for 'Unspecified interval'.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Plug Control Registers have two fields related to the number of established
connections, one is 'Broadcast connection counter' and another is
'Point-to-point connection counter'. The driver can know there are established
connections or not to check these fields.
This commit is for considering about JACK/FFADO streaming. Currently, when
JACK/FFADO starts its streaming to the device, cmp_connection_establish() is
failed expectedly. This seems to be enough but there are some devices which
needs to change sampling frequency before trying to establish connections.
For such devices, this functionality is needed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds some macros, codes with condition of direction and new functions
to handle output connection. Once cmp_connection_init() is executed with its
direction, CMP input and output connection can be handled by the same way.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds 'direction' member to 'cmp_connection' structure to indicate
the direction of connection. This patch also adds 'direction' argument to
cmp_connection_init() function to determine the direction.
The cmp_connection_init() function is exported and used in snd-firewire-speakers
so this patch also affect it.
This patch just add them. Actual implementation will be done by followed
patches.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Referring to IEC 61883-1, oMPR and iMPR, oPCR and iPCR have some fields with
the same role in the same position. This patch renames some macros, variables
and function arguments with "i" in its prefix to reuse them between oMPR and
iMPR, oPCR and iPCR.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, drivers can bring XRUN state for PCM substreams when error to
queue packets or detecting discontinuity of packet. The application may try to
recover this state by calling snd_pcm_prepare().
Depending on each driver, .prepare() includes restart streaming. Then there
is a state that PCM substreams are running but isochronous contexts are
stopped. In this case, when .pointer() is called, it refers to error pointer.
This commit is for a prevention of this bug.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds common PCM constraints according to current firewire-lib
implementation.
1.Maximum width for each sample is limited by 24.
AM824 in IEC 61883-6 can deliver 24bit data.
2. Minimum time for period is 5msec.
Apply the old value. For shorter latency, further works are needed.
3. In blocking mode, frames per period/buffer is aligned to 32.
Each packet can include some frames depending on its sampling rate. In
blocking mode, the number equals to SYT_INTERVAL. Currently firewire-lib
can schedule snd_pcm_period_elapsed() for each packet. So, for accurate
PCM interrupt, the number of frames per period/buffer should be aligned
to SYT_INTERVAL.
Currently firewire-lib is lack of better rules to achieve this. So LCM of
each value of SYT_INTERVALs (=32) is applied. This can be improved for
further work.
[Fixed the compile error due to the missing "&" by tiwai]
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, AMDTP functionality in firewire-lib supports mapping
for PCM data channels. With this mapping, firewire-lib can obsolete
a flag, CIP_HI_DUALWIRE, but Dice driver still keeps dual wire mode.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices arrange the position of PCM/MIDI data channel in AMDTP packet.
This commit allows drivers to set channel mapping.
To be simple, the mapping table is an array with fixed length. Then the number
of channels for PCM is restricted by 64 channels.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Generally, the devices can synchronize to handle 'presentation timestamp'
in CIP packets. This commit adds functionality to pick up this timestamp from
in-packets transmitted by the device, then use it for out packets.
In current implementation, this module generated the timestamp by itself. This
is 'SYT Match' mode. Then drivers with this module acts as synchronization
master. This commit allows this module to act as synchronization slave.
This commit restricts this mechanism is only available in blocking mode because
handling the timestamp in non-blocking mode is more complicated than in
blocking mode.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For duplex streams with synchronization, drivers should pick up
'presentation timestamp' from in-packets and use the timestamp for
out-packets. This commit is preparation for this.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For capturing/playbacking MIDI messages, this commit adds one MIDI conformant
data channel. This data channel has multiplexed 8 MIDI data streams. So this
data channel can transfer messages from/to 8 MIDI ports.
And this commit allows to set PCM format even if AMDTP streams already start.
I suppose the case that PCM substreams are going to be joined into AMDTP
streams when AMDTP streams are already started for MIDI substreams. Each
driver must count how many PCM/MIDI substreams use AMDTP streams to stop
AMDTP streams.
There are differences between specifications about MIDI conformant data.
About the multiplexing, IEC 61883-6:2002, itself, has no information. It
describes labels and bytes for MIDI messages and refers to MMA/AMEI RP-027
for 'successfull implementation'. MMA/AMEI RP-027 describes 8 MPX-MIDI data
streams for one MIDI conformant data channel. IEC 61883-6:2005 adds
'sequence multiplexing' and apply this way and describe incompatibility
between 2002 and 2005.
So this commit applies IEC 61883-6:2005. When we find some devices compliant
to IEC 61883-6:2002, then this difference should be handles as device quirk
in additional work.
About the number of bytes in an MIDI conformant data, IEC 61883-6:2002 describe
0,1,2,3 bytes. MMA/AMEI RP-027 describes 'MIDI1.0-1x-SPEED', 'MIDI1.0-2x-SPEED',
'MIDI1.0-3x-SPEED' modes and the maximum bytes for each mode corresponds to 1,
2, 3 bytes. The 'MIDI1.0-2x/3x-SPEED' modes are accompanied with 'negotiation
procedure' and 'encapsulation details' but there is no specifications for them.
So this commit implements 'MIDI1.0-1x-SPEED' mode for playback, but allows
to pick up 1-3 bytes for capturing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For capturing PCM, this commit adds the functionality to handle in-stream.
This is also applied for dual-wire mode.
Currently, capturing 32bit samples are supported.
When the sequence of in-packet has discontinuity of dbc, in-stream isn't handled
and amdtp_streaming_error() returns true.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some codes can be reused to handle in-stream. This commit adds new functions.
This commit also renames some functions to keep naming consistency.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds 'direction' member to amdtp_stream structure to indicate its
direction. This patch also adds 'direction' argument to amdtp_stream_init()
function to determine its direction.
The amdtp_stream_init() function is exported and used by firewire-speakers and
dice so this patch also affects them.
This patch just add them. Actual implementation will be done by followed
patches.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds some macros instead of fixed value for AMDTP according to
IEC 61883-1/6. These macros will also be used by followed patches.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch renames some functions, a structure and its member to reuse them
in both AMDTP in/out stream.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The array limits are supposed to be in units of u32 instead of in bytes.
The current code has a potential array overflow.
Fixes: c614475b0e ('ALSA: dice: add a proc file to show device information')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of small fixes in HD-audio quirks and runtime PM, ASoC
rcar, abs8500 and other codecs. Most of commits are for stable
kernels, too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zoMb
-----END PGP SIGNATURE-----
Merge tag 'sound-fix2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull second set of sound fixes from Takashi Iwai:
"A collection of small fixes in HD-audio quirks and runtime PM, ASoC
rcar, abs8500 and other codecs. Most of commits are for stable
kernels, too"
* tag 'sound-fix2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Set current_headset_type to ALC_HEADSET_TYPE_ENUM (janitorial)
ALSA: hda - Provide missing pin configs for VAIO with ALC260
ALSA: hda - Add headset quirk for Dell Inspiron 3135
ALSA: hda - Fix the headphone jack detection on Sony VAIO TX
ALSA: hda - Fix missing bass speaker on ASUS N550
ALSA: hda - Fix unbalanced runtime PM notification at resume
ASoC: arizona: Set FLL to free-run before disabling
ALSA: hda - A casual Dell Headset quirk
ASoC: rcar: fixup dma_async_issue_pending() timing
ASoC: rcar: off by one in rsnd_scu_set_route()
ASoC: wm5110: Add post SYSCLK register patch for rev D chip
ASoC: ab8500: Revert to using custom I/O functions
ALSA: hda - Also enable mute/micmute LED control for "Lenovo dock" fixup
ALSA: firewire-lib: include sound/asound.h to refer to snd_pcm_format_t
ALSA: hda - Select FW_LOADER from CONFIG_SND_HDA_CODEC_CA0132_DSP
ALSA: hda - Enable mute/mic-mute LEDs for more Thinkpads with Realtek codec
ASoC: rcar: fixup mod access before checking
This commit fix out of specification about the value of FDF field in out packet
with 'no data'. This affects blocking mode.
According to IEC 61883-6, there is two way to generate AMDTP packets include no
data in blocking mode.
Way 1. an empty packet defined in IEC 61883-1
- Size of packet is 2 quadlets.
- The value of FDF is sfc.
- The packet includes only CIP headers
Way 2. a special non-empty packet defined in IEC 61883-6
- Size of packet is following to blocking mode
- The value of FDF is 0xff. This value is 'NO-DATA'. This means 'The receiver'
must ignore all the data in a CIP with this FDF code'.
- The packet includes dummy data.
But current implementation is a combination of them.
- Size of packet is 2 (way 1)
- FDF = 0xff (way 2)
This causes BeBoB chipset cannot sound.
This patch applies Way 1.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'snd_pcm_format_t' is used by amdtp_out_stream_set_pcm_format().
Currently, when just including amdtp.h, compiler cannot find this type because
this type is defined in uapi/sound/asound.h and this header is not included by
amdtp.h.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At the moment, this driver supports only playback, while FFADO supports
(only) full-duplex devices. So, prevent conflicts by not claiming
devices that would be better handled by FFADO.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
While most DICE devices keep TCAT's default category ID of 0x04, Weiss
devices identify themselves with 0x00.
Reported-by: Rolf Anderegg <rolf.anderegg@weiss.ch>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Doing accesses without quadlet alignment is a bad idea because the
firmware's byte-swapping would garble the data; clarify this in the
documentation.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Instead of relying of some control panel application to configure some
fixed sample rate, allow applications to set it automatically.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
In preparation for sample rate selection support, read the stream
parameters that might change when running at different sample rates.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
In preparation for sample rate selection support, ensure that the driver
knows about the device's clock capabilities.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Avoid a lock inversion between dice->mutex and pcm->open_mutex.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Since commit f2b3614cef (Don't check DMA time-out too shortly), we
need no longer to restrict the period length to less than 10 s.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When a bus reset happens, the enable register is automatically cleared,
so we do not need to clear it manually when stopping the stream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add a flag to snd_fw_transaction() to allow it to abort when a bus reset
happens. This removes most of the duplicated error handling loops that
were required around calls to the low-level fw_run_transaction().
Also add a flag to suppress error messages; errors are expected when we
attempt to clean up after the device was unplugged.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Change the AMDTP streaming code to handle the non-standard stream format
that DICE devices use at sample rates greater than 96 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
DICE devices do not have a unique specifier ID in their unit directory
(it's always the same as the device vendor's ID), so rely on just the
version ID for driver loading, and use a heuristic in the probe callback
to detect actual DICE devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Introduce the helper function amdtp_out_stream_running(). This makes
many checks in amdtp.c clearer and frees the device drivers from having
to track this with a separate variable.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When aborting a PCM stream, the xrun is signaled only if the stream is
running. When disconnecting a PCM stream, calling snd_card_disconnect()
too early would change the stream into a non-running state and thus
prevent the xrun from being noticed by user space.
To prevent this, move the snd_card_disconnect() call after the xrun.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Allow AMDTP output streams to use blocking mode.
Use it for DICE devices, because the old DICE-II chip will in some cases
not be able to lock to non-blocking streams (erratum E7).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Instead of forcing a constant 44.1 kHz, read the current sample rate
from the device when opening the PCM device.
Actually changing the sample rate requires some separate controller
application.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
After a bus reset, do not stop the stream completely to avoid having to
reconfigure the device when restarting the stream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
As a start point for further development, this is an incomplete driver
for DICE devices:
- only playback (so no clock source except the bus clock)
- only 44.1 kHz
- no MIDI
- recovery after bus reset is slow
- hwdep device is created, but not actually implemented
Contains compilation fixes by Stefan Richter.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Calculating frame bytes can be replaced with inline function in
include/sound/pcm.h.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make struct ieee1394_device_id.driver_data actually avaliable to
1394 protocol drivers. This is especially useful to 1394 audio drivers
for model-specific parameters and methods.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=8MqX
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire updates from Stefan Richter:
"Make struct ieee1394_device_id.driver_data actually avaliable to 1394
protocol drivers. This is especially useful to 1394 audio drivers for
model-specific parameters and methods"
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: remove support of fw_driver.driver.probe and .remove methods
firewire: introduce fw_driver.probe and .remove methods
"pcm" member in struct fwspk is used to set pcm operations but is not used
again. This commit remove this member and set pcm operations with
snd_pcm_set_ops().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix to return -ENOMEM in the kmalloc() error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
FireWire upper layer drivers are converted from generic
struct driver.probe() and .remove()
to bus-specific
struct fw_driver.probe() and .remove().
The new .probe() adds a const struct ieee1394_device_id *id argument,
indicating the entry in the driver's device identifiers table which
matched the fw_unit to be probed. This new argument is used by the
snd-firewire-speakers driver to look up device-specific parameters and
methods. There is at least one other FireWire audio driver currently in
development in which this will be useful too.
The new .remove() drops the unused error return code.
Although all in-tree drivers are being converted to the new methods,
support for the old methods is left in place in this commit. This
allows public developer trees to merge this commit and then move to the
new fw_driver methods.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de> (for sound/firewire/)
Cc: Peter Hurley <peter@hurleysoftware.com> (for drivers/staging/fwserial/)
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a MIDI driver for the Stanton FireWire DJ controllers.
Tested-by: Sean M. Pappalardo - D.J. Pegasus <spappalardo@mixxx.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
- Fix mismatch between DMA mapping direction (was wrong) and DMA synchronization
direction (was correct) of isochronous reception buffers of userspace drivers
if vma-mapped for R/W access. For example, libdc1394 was affected.
- more consistent retry stategy in device discovery/ rediscovery, and improved
failure diagnostics
- various small cleanups, e.g. use SCSI layer's DMA mapping API in firewire-sbp2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=fulr
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull IEEE 1394 (FireWire) subsystem updates from Stefan Richter:
- Fix mismatch between DMA mapping direction (was wrong) and DMA
synchronization direction (was correct) of isochronous reception
buffers of userspace drivers if vma-mapped for R/W access. For
example, libdc1394 was affected.
- more consistent retry stategy in device discovery/ rediscovery, and
improved failure diagnostics
- various small cleanups, e.g. use SCSI layer's DMA mapping API in
firewire-sbp2
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: sbp2: document the absence of alignment requirements
firewire: sbp2: remove superfluous blk_queue_max_segment_size() call
firewire: sbp2: use scsi_dma_(un)map
firewire: sbp2: give correct DMA device to scsi framework
firewire: core: fw_device_refresh(): clean up error handling
firewire: core: log config rom reading errors
firewire: core: log error in case of failed bus manager lock
firewire: move rcode_string() to core
firewire: core: improve reread_config_rom() interface
firewire: core: wait for inaccessible devices after bus reset
firewire: ohci: omit spinlock IRQ flags where possible
firewire: ohci: correct signedness of a local variable
firewire: core: fix DMA mapping direction
firewire: use module_pci_driver
Trying to flush completed packets is pointless when the pointer
callback was called from the packet completion callback; avoid it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By flushing all completed but not yet reported packets before reading
the PCM hardware position, the granularity of the pointer is improved
from the interrupt interval to the packet size.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The following patch might introduce this call chain:
PCM .pointer callback
+ fw_iso_context_flush_completions
+ packet callback
+ snd_pcm_period_elapsed
+ PCM .pointer callback
Recursive calls to the pointer callback are not possible due to the PCM
group locking, so avoid this by moving the period notification into
a separate tasklet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is nothing audio-specific about the rcode_string() helper, so move
it from snd-firewire-lib into firewire-core to allow other code to use it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (fixed sound/firewire/cmp.c)
- Some SBP-2 initiator fixes, side product from ongoing work on a target.
- Reintroduction of an isochronous I/O feature of the older ieee1394 driver
stack (flush buffer completions); it was evidently rarely used but not
actually unused. Matching libraw1394 code is already available.
- Be sure to prefix all kernel log messages with device name or card name,
and other logging related cleanups.
- Misc other small cleanups, among them a small API change that affects
sound/firewire/ too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=oWbr
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull IEEE 1394 (FireWire) subsystem updates post v3.3 from Stefan Richter:
- Some SBP-2 initiator fixes, side product from ongoing work on a target.
- Reintroduction of an isochronous I/O feature of the older ieee1394 driver
stack (flush buffer completions); it was evidently rarely used but not
actually unused. Matching libraw1394 code is already available.
- Be sure to prefix all kernel log messages with device name or card name,
and other logging related cleanups.
- Misc other small cleanups, among them a small API change that affects
sound/firewire/ too. Clemens Ladisch is aware of it.
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394: (26 commits)
firewire: allow explicit flushing of iso packet completions
firewire: prevent dropping of completed iso packet header data
firewire: ohci: factor out iso completion flushing code
firewire: ohci: simplify iso header pointer arithmetic
firewire: ohci: optimize control bit checks
firewire: ohci: remove unused excess_bytes field
firewire: ohci: copy_iso_headers(): make comment match the code
firewire: cdev: fix IR multichannel event documentation
firewire: ohci: fix too-early completion of IR multichannel buffers
firewire: ohci: move runtime debug facility out of #ifdef
firewire: tone down some diagnostic log messages
firewire: sbp2: replace a GFP_ATOMIC allocation
firewire: sbp2: Fix SCSI sense data mangling
firewire: sbp2: Ignore SBP-2 targets on the local node
firewire: sbp2: Take into account Unit_Unique_ID
firewire: nosy: Use the macro DMA_BIT_MASK().
firewire: core: convert AR-req handler lock from _irqsave to _bh
firewire: core: fix race at address_handler unregistration
firewire: core: remove obsolete comment
firewire: core: prefix log messages with card name
...
fw_unit device drivers invariably need to talk to the fw_unit's parent
(an fw_device) and grandparent (an fw_card). firewire-core already
maintains an fw_card reference for the entire lifetime of an fw_device.
Likewise, let firewire-core maintain an fw_device reference for the
entire lifetime of an fw_unit so that fw_unit drivers don't have to.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
These aren't modules, but they do make use of these macros, so
they will need export.h to get that definition. Previously,
they got it via the implicit module.h inclusion.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There is a lock inversion between fwspk->mutex and pcm->open_mutex
reported by lockdep when fwspk_hw_free is called.
Fixed by copying the fix from the same former issue in the isight
sound driver (commit f3f7c1837f
"ALSA: isight: fix locking").
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove a field that is not used at all. This remained from
earlier tests, but the current driver has decided not to handle
iris notifications.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit 13882a82ee (optimize iso queueing by setting
wake only after the last packet), drivers are required to call
fw_iso_context_queue_flush() after queueing a batch of packets.
The missing call would have an effect only if the controller
queue underruns, but then the DMA would stop completely.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit f2b3614cef (Don't check DMA time-out too shortly),
drivers need no longer restrict their PCM period length to be shorter
than 10 seconds.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lockdep complains about conflicts between isight->mutex,
ALSA's register_mutex, mm->mmap_sem, and pcm->open_mutex.
This can be fixed by moving the calls to isight_pcm_abort(),
snd_card_disconnect(), and fw_iso_resources_update() out of
isight->mutex. These functions are designed to be called
asynchronously; the mutex needs to protect only the device
streaming state modified by isight_start/stop_streaming().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Experiments have shown this driver to work now.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When aborting a PCM stream, the xrun is signaled only if the stream is
running. When disconnecting a PCM stream, calling snd_card_disconnect()
too early would change the stream into a non-running state and thus
prevent the xrun from being noticed by user space.
To prevent this, move the snd_card_disconnect() call after the xrun.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
which is needed to get the iSight to talk.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the .header_size field when queueing packets to avoid a division by
zero.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After handling a received packet, we want to resubmit the same packet,
so do not increase the packet index too early.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix crashes in isight_pcm_abort() that happen when the driver tries to
access isight->pcm->runtime which does not exist when the device is not
open. Introduce a new field pcm_active to track this state.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds an experimental driver for the front and rear microphones of
the Apple iSight web camera.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When queueing iso packets, the run time is dominated by the two
MMIO accesses that set the DMA context's wake bit. Because most
drivers submit packets in batches, we can save much time by
removing all but the last wakeup.
The internal kernel API is changed to require a call to
fw_iso_context_queue_flush() after a batch of queued packets.
The user space API does not change, so one call to
FW_CDEV_IOC_QUEUE_ISO must specify multiple packets to take
advantage of this optimization.
In my measurements, this patch reduces the time needed to queue
fifty skip packets from userspace to one sixth on a 2.5 GHz CPU,
or to one third at 800 MHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We do not need slab allocations anymore in order to satisfy
streaming DMA mapping constraints, thanks to commit da28947e7e
"firewire: ohci: avoid separate DMA mapping for small AT payloads".
(Besides, the slab-allocated buffers that firewire-core, firewire-sbp2,
and firedtv used to provide for 8-byte write and lock requests were
still not fully portable since they crossed cacheline boundaries or
shared a cacheline with unrelated CPU-accessed data. snd-firewire-lib
got this aspect right by using an extra kmalloc/ kfree just for the
8-byte transaction buffer.)
This change replaces kmalloc'ed lock transaction scratch buffers in
firewire-core, firedtv, and snd-firewire-lib by local stack allocations.
Perhaps the most notable result of the change is simpler locking because
there is no need to serialize usages of preallocated per-device buffers
anymore. Also, allocations and deallocations are simpler.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
When aborting a PCM stream, the xrun is signaled only if the stream is
running. When disconnecting a PCM stream, calling snd_card_disconnect()
too early would change the stream into a non-running state and thus
prevent the xrun from being noticed by user space.
To prevent this, move the snd_card_disconnect() call after the xrun.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fixes this error:
sound/firewire/fcp.c: In function 'fcp_avc_transaction':
sound/firewire/fcp.c:103: error: implicit declaration of function 'msleep'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an AMDTP stream error state that occurs when we fail to queue
another packet. In this case, the stream is stopped, and the error can
be reported when the application tries to restart the PCM stream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For correct cache coherency on some architectures, DMA buffers must be
allocated in a different cache line than data that is concurrently used
by the CPU.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In non-blocking mode, the SYT_INTERVAL is larger than the number of
audio frames in each packet, so there are packets that do not contain
any frame to which the SYT could be applied. For these packets, the
SYT must not be the timestamp of the next valid SYT frame, but the
special no-info SYT value.
This fixes broken playback on the FireWave at 44.1 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a driver for two playback-only FireWire devices based on the OXFW970
chip.
v2: better AMDTP API abstraction; fix fw_unit leak; small fixes
v3: cache the iPCR value
v4: FireWave constraints; fix fw_device reference counting;
fix PCR caching; small changes and fixes
v5: volume/mute support; fix crashing due to pcm stop races
v6: fix build; one-channel volume for LaCie
v7: use signed values to make volume (range checks) work; fix function
block IDs for volume/mute; always use channel 0 for LaCie volume
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto