* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
This patch reverts the driver to enabling/disabling the NFC interrupt
mask rather than enabling/disabling the system interrupt. This cleans
up the driver so that it doesn't rely on interrupts being disabled
within the interrupt handler.
For i.MX21 we keep the current behaviour, that is calling
enable_irq/disable_irq_nosync to enable/disable interrupts. This patch
is based on earlier work by John Ogness.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch modifies the DaVinci NAND driver to use the
new AEMIF timing setup API to configure the NAND access
timings.
Earlier, AEMIF configuration was being done as a special
case for DM644x board, but now more boards emerge which have
capability to boot for other media (SPI flash, NOR flash) and
have the kernel access NAND flash. This means that kernel cannot
always depend on the bootloader to setup the NAND.
Also, on platforms such as da850/omap-l138, the aemif input
frequency changes as cpu frequency changes; necessiating
re-calculation of timimg values as part of cpufreq transtitions.
This patch forms the basis for adding that support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds support to configure the AEMIF interface
with supplied timing values.
Since this capability is useful both from NOR and NAND
flashes, it is provided as a new interface and in a file
of its own.
AEMIF timing configuration is required in cases:
1) Where the AEMIF clock rate can change at runtime (a side
affect of cpu frequency change).
2) Where U-Boot does not support NAND/NOR but supports other
media like SPI Flash or MMC/SD and thus does not care about
setting up the AEMIF timing for kernel to use.
3) Where U-Boot just hasn't configured the timing values and
cannot be upgraded because the box is already in the field.
Since there is now a header file for AEMIF interface, the
common (non-NAND specific) defines for AEMIF registers have
been moved from nand.h into the newly created aemif.h
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch initializes the pages per block field in CONFIG1 for
v2 controllers. It also sets the FP_INT field. This is the last
field not correctly initialized, so we can switch from
read/modify/write the CONFIG1 reg to just write the correct
value.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since info->mtd isn't dynamically allocated, we shouldn't attempt to
kfree() it. Otherwise we get random fun corruption when unloading
the driver built as a module.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Seems some patches got out sync when being merged. The Blackfin NFC
driver was updated to use nand_scan_ident(), but it missed the change
where nand_scan_ident() now takes 3 arguments. So update this driver
to fix build failures.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch avoids byte access to the NFC buffer. Byte access to the
NFC is not allowed.
The patch is against linux-next 20100618.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Apparently, the check for a 6-byte ID string introduced by commit
426c457a32 ("mtd: nand: extend NAND flash
detection to new MLC chips") is NOT sufficient to determine whether or
not a Samsung chip uses their new MLC detection scheme or the old,
standard scheme. This adds a condition to check cell type.
Signed-off-by: Tilman Sauerbeck <tilman@code-monkey.de>
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Commit c7b28e25cb ("mtd: nand: refactor BB
marker detection") caused a regression in detection of factory-set bad
block markers, especially for certain small-page NAND. This fix removes
some unneeded constraints on using NAND_SMALL_BADBLOCK_POS, making the
detection code more correct.
This regression can be seen, for example, in Hynix HY27US081G1M and
similar.
Signed-off-by: Brian Norris <norris@broadcom.com>
Tested-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Test on a PXA310 platform with Samsung K9F2G08X0B NAND flash,
with tCH=5 and clk is 156MHz, ns2cycle(5, 156000000) returns -1.
ns2cycle returns negtive value will break NDTR0_tXX macros.
After checking the commit log, I found the problem is introduced by
commit 5b0d4d7c8a
"[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accurately"
To get num of clock cycles, we use below equation:
num of clock cycles = time (ns) / one clock cycle (ns) + 1
We need to add 1 cycle here because integer division will truncate the result.
It is possible the developers set the Min values in SPEC for timing settings.
Thus the truncate may cause problem, and it is safe to add an extra cycle here.
The various fields in NDTR{01} are in units of clock ticks minus one,
thus we should subtract 1 cycle then.
Thus the correct equation should be:
num of clock cycles = time (ns) / one clock cycle (ns) + 1 - 1
= time (ns) / one clock cycle (ns)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
* git://git.infradead.org/mtd-2.6:
mtd/nand_ids: Fix buswidth
mtd/m25p80: fix test for end of loop
mtd/m25p80: retlen is never NULL
MIPS: Fix gen_nand probe structures contents
gen_nand: Test if nr_chips field is valid
BFIN: Fix gen_nand probe structures contents
nand/denali: move all hardware initialization work to denali_hw_init
nand/denali: Add a page check in denali_read_page & denali_read_page_raw
nand/denali: use cpu_relax() while waiting for hardware interrupt
nand/denali: change read_status function method
nand/denali: Fixed check patch warnings
ARM: Fix gen_nand probe structures contents
mtd/nand_base: fix kernel-doc warnings & typos
nand/denali: use dev_xx debug function to replace nand_dbg_print and some printk
nand/denali: Fixed handle ECC error bugs
nand/denali: use iowrite32() to replace denali_write32()
nand/denali: Fixed probe function bugs
The buswidth for chips of ID 0xD7 is x8, not x16.
This was my previous typo.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All hardware initialization will be done in denali_hw_init before
irq handler registered
Change mtd name from "DENALI NAND" to be "denali-nand" since whitespace in
name can cause problems if we use cmdlinepart
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In mtd->write, Denali controller will use MODE_11 mode to read
NAND flash status, then return back to MODE_1O mode to do page
write.
Here comes a bug for this kind of using, sometimes controller will
not write data to NAND and just return a good interrupt to tell
driver writing work is done. The data in this page is all 0xff and
this page can not be written again. The reason is unknow.
So read Denali controller register WRITE_PROTECT to get NAND status
instead.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
waring: no space for starting a line
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix mtd/nand_base.c kernel-doc warnings and typos.
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'invert'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:2087): No description found for parameter 'len'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mtd/nand_base.c kernel-doc warnings and typos.
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'invert'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:2087): No description found for parameter 'len'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Once the last ECC error was handled, controller will triger an
interrupt. If this interrupt can not be clean on time, controller
may corrupt.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
denali_write32() just implements a debug function for iowrite32(),
only print out the write value. Remove this function since it's useless
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixed a pci_resource_len function error;
Changed returning sequence of probe function;
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (79 commits)
mtd: Remove obsolete <mtd/compatmac.h> include
mtd: Update copyright notices
jffs2: Update copyright notices
mtd-physmap: add support users can assign the probe type in board files
mtd: remove redwood map driver
mxc_nand: Add v3 (i.MX51) Support
mxc_nand: support 8bit ecc
mxc_nand: fix correct_data function
mxc_nand: add V1_V2 namespace to registers
mxc_nand: factor out a check_int function
mxc_nand: make some internally used functions overwriteable
mxc_nand: rework get_dev_status
mxc_nand: remove 0xe00 offset from registers
mtd: denali: Add multi connected NAND support
mtd: denali: Remove set_ecc_config function
mtd: denali: Remove unuseful code in get_xx_nand_para functions
mtd: denali: Remove device_info_tag structure
mtd: m25p80: add support for the Winbond W25Q32 SPI flash chip
mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips
mtd: m25p80: add support for the EON EN25P{32, 64} SPI flash chips
...
Fix up trivial conflicts in drivers/mtd/maps/{Kconfig,redwood.c} due to
redwood driver removal.
Nand devices with at least 26 bytes of oob data per 512 byte block
can have 8bit ecc on v2 type controllers. This is currently not tested,
but at least this patch puts the ECC_MODE bit into a well defined state.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The v2 controller has a totally different mechanism to check
whether the data we read had ecc errors or not. Implement this.
The mechanism in the v2 controller happens to be identical to
the v3 controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This prepares the driver for v3 support. The v3 controller
has a completely different register layout, so add a V1_V2_
namespace to the register defines to avoid confusion with
the v3 regs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch prepares the driver to add v3 controller support
later. The v3 controller is basically the same controller as v1
and v2, but with a completely different register layout.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We save/restore the value in the buffer anyway, so it makes
no difference whether we use main_area0 or main_area1. So,
we can use main_area0 and remove main_area1 from the driver
which is otherwise unused. Also, clean up the comments in
get_dev_status.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the offset to the register base instead. This is done
in preparation for v3 controller support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
set_ecc_config function only set ECC_CORRECTION register, so
move register setting to probe function.
Since controller only support 15bit and 8bit ecc correction,
updated nand ecc layout information.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Hi David,
I sent 4 patches using my intel email account. If there is any
problem about the format of these patches, I will resend them after
I arrived at home by using my gmail account, and I will keep on
using gmail account to send patches.
Thanks.
>From 242e3bf5e17f54b1df8cf285154a7c7a61ff62e9 Mon Sep 17 00:00:00 2001
From: Chuanxiao Dong <chuanxiao.dong@intel.com>
Date: Fri, 6 Aug 2010 15:29:41 +0800
Subject: [PATCH 1/4] mtd: denali: Remove device_info_tag structure.
Most of the variables in this structure are useless, so just
remove this structure and relevant codes.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
This patch fixes
drivers/mtd/nand/atmel_nand.c:372: warning: 'part_probes' defined but not used
which is issued when CONFIG_MTD_PARTITIONS is defined but
CONFIG_MTD_CMDLINE_PARTS not.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch corrects a problem where gen_nand driver assumed there can be only
one chip and ignored the pdata->chip.nr_chips value.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Linus Torvalds