When attempting a command abort we should check the command status prior
to sending the abort; the command might've been completed already.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abstract accesses to the scsi_lookup array by introducing
mpt3sas_get_st_from_smid().
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just a wrapper around the scsi lookup array and only used in one place,
so open-code it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use 'list_splice_init()' instead of hand-crafted function. No
functional change.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. In IO path, setting of "ATA command pending" flag early before device
removal, invalid device handle etc., checks causes any new commands
to be always returned with SAM_STAT_BUSY and when the driver removes
the drive the SML issues SYNC Cache command and that command is
always returned with SAM_STAT_BUSY and thus making SYNC Cache command
to requeued.
2. If the driver gets an ATA PT command for a SATA drive then the driver
set "ATA command pending" flag in device specific data structure not
to allow any further commands until the ATA PT command is completed.
However, after setting the flag if the driver decides to return the
command back to upper layers without actually issuing to the firmware
(i.e., returns from qcmd failure return paths) then the corresponding
flag is not cleared and this prevents the driver from sending any new
commands to the drive.
This patch fixes above two issues by setting of "ATA command pending"
flag after checking for whether device deleted, invalid device handle,
device busy with task management. And by setting "ATA command pending"
flag to false in all of the qcmd failure return paths after setting the
flag.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No Functional change just cleanup. Removed variable requeue_event and
made function as void.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
pr_info() has a KERN_INFO already so the second KERN_INFO isn't needed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The indenting wasn't right, because the last two prints weren't indented
far enough. Also it used pr_info() where it was supposed to use
pr_cont(). I reversed the if statement and pulled the code in one tab
and did a couple other minor cleanups.
Fixes: 4318c73478 ("scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The newly added base_make_prp_nvme function triggers a build warning on
some 32-bit configurations:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function 'base_make_prp_nvme':
drivers/scsi/mpt3sas/mpt3sas_base.c:1664:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
msg_phys = (dma_addr_t)mpt3sas_base_get_pcie_sgl_dma(ioc, smid);
After taking a closer look, I found that the problem is that the new
code mixes up pointers and dma_addr_t values unnecessarily.
This changes it to use the correct types consistently, which lets us get
rid of a lot of type casts in the process. I'm also renaming some
variables to avoid confusion between physical and dma address spaces
that are often distinct.
Fixes: 016d5c35e2 ("scsi: mpt3sas: SGL to PRP Translation for I/Os to NVMe devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated mpt3sas driver version to 17.100.00.00
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Used variable __le64/__le32 whichever required in building NVME
PRP, and passed to LE Controller.
2) Remove unused functions, And Declared functions as static which are
used only in mpt3sas_scsih.c.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check for NVMe drives before enabling or checking tlr.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Added debug prints for pcie devices in ioctl debug path. Which
will be helpful for debugging.
* Added PCIe device support for ioctl BTDHMAPPING ioctl.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added debug information for NVMe/PCIe drives in target rest path
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After Controller reset, Scan and add nvme device back to the topology.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sets nvme device queue depth, name and displays device capabilities
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* The controller firmware sends separate events for NVMe devices and
PCIe switches similar to existing SAS events.
* NVMe device detection, addition and removal are reported by the
firmware through PCIe Topology Change list events.
* The PCIe device state change events are sent when the firmware
detects any abnormal conditions with a NVMe device or switch.
* The enumeration event are sent when the firmware starts PCIe device
enumeration and stops.
* This patch has the code change to handle the events and add/remove
NVMe devices in driver's inventory.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following functions are called in nvme drive remove path:
_scsih_pcie_device_remove_by_handle
_scsih_pcie_device_remove_from_sml
[mkp: clarify commit message]
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Below Functions are added in various paths to support NVMe drive
addition.
_scsih_pcie_add_device
_scsih_pcie_device_add
_scsih_pcie_device_init_add
_scsih_check_pcie_access_status
_scsih_pcie_check_device
mpt3sas_get_pdev_by_handle
mpt3sas_config_get_pcie_device_pg0
mpt3sas_config_get_pcie_device_pg2
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Mpt3sas driver uses the NVMe Encapsulated Request message to send an
NVMe command to an NVMe device attached to the IOC.
* Normal I/O commands like reads and writes are passed to the
controller as SCSI commands and the controller has the ability to
translate the commands to NVMe equivalent.
* This encapsulated NVMe command is used by applications to send
direct NVMe commands to NVMe drives.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Added support for translating the SGLs associated with incoming
commands either to IEE SGL or NVMe PRPs for NVMe devices.
* The hardware translation of IEEE SGL to NVMe PRPs has limitations
and if a command cannot be translated by hardware then it will go to
firmware and the firmware needs to translate it. This will have a
performance impact. To avoid that, the driver proactively checks
whether the translation will be done in hardware or not. If not, then
driver translates.
[mkp: clarified commit message]
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Added support for probing pcie device and adding NVMe drives to SML
and driver's internal list pcie_device_list.
2) Added support for determing NVMe as boot device.
3) Added nvme device support for call back functions scan_finished
target_alloc,slave_alloc,target destroy and slave destroy.
a) During scan, pcie devices are probed and added to SML to drivers
internal list.
b) target_alloc & slave alloc API's allocates resources for
(MPT3SAS_TARGET & MPT3SAS_DEVICE) private datas and holds information
like handle, target_id etc.
c) slave_destroy & target_destroy are called when driver unregisters
or removes device. Also frees allocated resources and info.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Bump mpt3sas driver version to v16.100.00.00
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding PNP ID of Mercator i.e. SAS3616 HBA device. Its device ID is
0xD1 and vendor ID is 0x1000.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enclosure handles are not updated after host reset. As a result, driver
device structure is holding previously assigned enclosure handle which
is different from the enclosure handle populated in the corresponding
device page.
Modified the driver to update devices enclosure handles after host reset
to current value by referring the enclosure handles from corresponding
device pages
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Display chassis slot information along with other drive location
parameters such as slot number and connector name in the logs if
chassis slot validity bit is set in 'SAS Enclosure Page 0'.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated MPI headers to v2.00.48
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whenever an I/O for a RAID volume fails with IOCStatus
MPI2_IOCSTATUS_SCSI_IOC_TERMINATED and SCSIStatus equal to
(MPI2_SCSI_STATE_TERMINATED | MPI2_SCSI_STATE_NO_SCSI_STATUS) then
return the I/O to SCSI midlayer with "DID_RESET" (i.e. retry the IO
infinite times) set in the host byte.
Previously, the driver was completing the I/O with "DID_SOFT_ERROR"
which causes the I/O to be quickly retried. However, firmware needed
more time and hence I/Os were failing.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Dev Handles whose value is less than HBA's phys count number, driver
would return HBA's SAS address value. As a result, for a Virtual SES
device the driver was returning the HBA's SAS address. Updated the
driver to return Virtual SES' SAS address.
[mkp: clarified commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To reduce the memory footprint of the driver in the kdump kernel, we
apply the following settings when reset_devices is set:
1. Use single MSI-x vector.
2. Disable RDPQ mode.
3. Set sg_table_size to 32 by default.
4) Set SCSI IO Queue depth to 200.
[mkp: fixed commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While removing Expander devices, we are removing expander device entry
from the list before freeing its child devices. While freeing child
device we are finding its parent device node as NULL and therefore we
are not freeing the child device's allocated data structures. Updated
the driver to remove the expander device from the list only after
freeing all its child devices.
[mkp: clarified commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Earlier Active Cable Exception event with reason code "Cable Degraded
(0x02))" was added only for Active Cable. Now this event is extended to
Passive cable too. Re-arranged display message accordingly.
Also added Cable Exception Event event for SAS3008 & SAS3108 HBAs
(i.e. MPI 2.5 spec supporting HBAs). Previously, this event was enabled
only for MPI 2.6 spec supporting HBA devices.
[mkp: typos]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since right after the user copy, we are going to memset(&karg, 0,
sizeof(karg)), the copy_from_user is redundant
Signed-off-by: Meng Xu <mengxu.gatech@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simplify the SMP passthrough code by switching it to the generic bsg-lib
helpers that abstract away the details of the request code, and gets
drivers out of seeing struct scsi_request.
For the libsas host SMP code there is a small behavior difference in
that we now always clear the residual len for successful commands,
similar to the three other SMP handler implementations. Given that
there is no partial command handling in the host SMP handler this should
not matter in practice.
[mkp: typos and checkpatch fixes]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An optional discovery status should be printed with a pr_cont and needs
a leading space to make it more readable. The final new line should also
be a pr_cont and the indentation is out by one, so fix that too.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lines above this test, 8 'kzalloc' are performed, but only 7
results are tested.
Add the missing one (i.e. '!ioc->port_enable_cmds.reply').
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We print the driver name into one string and then add and ID
and copy it into a second string of the same length, at which
point gcc complains about a possible overflow:
drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function '_scsih_probe':
drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:21: error: '_cm' directive writing 3 bytes into a region of size between 1 and 32 [-Werror=format-overflow=]
printf(ioc->name, "%s_cm%d", ioc->driver_name, ioc->id);
^~~~~~~~~
drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:21: note: directive argument in the range [0, 255]
drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:2: note: 'sprintf' output between 5 and 38 bytes into a destination of size 32
sprintf(ioc->name, "%s_cm%d", ioc->driver_name, ioc->id);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Making the first string shorter is sufficient to avoid the
warning here, as we know it can only contain either "mpt2sas"
or "mpt3sas".
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This will make it easier to serialize SCSI device state changes through
a mutex.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of passing a "wait" argument to scsi_internal_device_block(),
split this function into a function that waits and a function that
doesn't wait. This will make it easier to serialize SCSI device state
changes through a mutex.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to relaxed ordering requirements on multiple architectures, drivers
are required to use wmb/rmb/mb combinations when they need to guarantee
observability between the memory and the HW.
The mpt3sas driver is already using wmb() for this purpose. However, it
issues a writel following wmb(). writel() function on arm/arm64
arhictectures have an embedded wmb() call inside.
This results in unnecessary performance loss and code duplication.
writel already guarantees ordering for both cpu and bus. we don't need
additional wmb()
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move scsi_remove_host call into sas_remove_host and remove it from SAS
HBA drivers, so we don't mess up the ordering. This solves an issue with
double deleting sysfs entries that was introduced by the change of sysfs
behaviour from commit bcdde7e221 ("sysfs: make __sysfs_remove_dir()
recursive").
[mkp: addressed checkpatch complaints]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Suggested-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Jinpu Wang <jinpu.wang@profitbricks.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jinpu Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did. The new stuff is basically lpfc
(nvme), qedi and aacraid. The fixes cover a lot of previously
submitted stuff, the most important of which probably covers some of
the failing irq vectors allocation and other fallout from having the
SCSI command allocated as part of the block allocation functions.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=e+6v
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did.
The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
cover a lot of previously submitted stuff, the most important of which
probably covers some of the failing irq vectors allocation and other
fallout from having the SCSI command allocated as part of the block
allocation functions"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
scsi: qedi: Fix memory leak in tmf response processing.
scsi: aacraid: remove redundant zero check on ret
scsi: lpfc: use proper format string for dma_addr_t
scsi: lpfc: use div_u64 for 64-bit division
scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
scsi: cciss: correct check map error.
scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
scsi: aacraid: Fixed expander hotplug for SMART family
scsi: mpt3sas: switch to pci_alloc_irq_vectors
scsi: qedf: fixup compilation warning about atomic_t usage
scsi: remove scsi_execute_req_flags
scsi: merge __scsi_execute into scsi_execute
scsi: simplify scsi_execute_req_flags
scsi: make the sense header argument to scsi_test_unit_ready mandatory
scsi: sd: improve TUR handling in sd_check_events
scsi: always zero sshdr in scsi_normalize_sense
scsi: scsi_dh_emc: return success in clariion_std_inquiry()
scsi: fix memory leak of sdpk on when gd fails to allocate
scsi: sd: make sd_devt_release() static
scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
...
Commit 669f044170 ("scsi: srp_transport: Move queuecommand() wait code
to SCSI core") can make scsi_internal_device_block() sleep. However,
the mpt3sas driver can call this function from an interrupt
handler. Hence add a second argument to scsi_internal_device_block()
that restores the old behavior of this function for the mpt3sas handler.
The call chain that triggered an "IRQ handler enabled interrupts"
complaint is as follows:
_base_interrupt()
-> _base_async_event()
-> mpt3sas_scsih_event_callback()
-> _scsih_check_topo_delete_events()
-> _scsih_block_io_to_children_attached_directly()
-> _scsih_block_io_device()
-> _scsih_internal_device_block()
-> scsi_internal_device_block()
Reported-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Omar Sandoval <osandov@osandov.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: <stable@vger.kernel.org> # v4.10+
Tested-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit <f2e767bb5d6e> ("mpt3sas: Force request partial completion
alignment") was not considering the case of commands not operating on
logical block size units (e.g. REQ_OP_ZONE_REPORT and its 64B aligned
partial replies). In this case, forcing alignment of resid to the device
logical block size can break the command result, e.g. in the case of
REQ_OP_ZONE_REPORT, the exact number of zone reported by the device.
Move the partial completion alignement check of mpt3sas to a generic
implementation in sd_done(). The check is added within the default
section of the initial req_op() switch case so that the report and reset
zone commands are ignored. In addition, as sd_done() is not called for
passthrough requests, resid corrections are not done as intended by the
initial mpt3sas patch.
Fixes: f2e767bb5d ("mpt3sas: Force request partial completion alignment")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix typos and add the following to the scripts/spelling.txt:
overwritting||overwriting
Link: http://lkml.kernel.org/r/1481573103-11329-29-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup the MSI-X handling allowing us to use the PCI-layer provided
vector allocation.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ). There's also an assortment of minor fixes and the
major update of switching a bunch of drivers to pci_alloc_irq_vectors
from Christoph.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cBQx
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ...).
There's also an assortment of minor fixes and the major update of
switching a bunch of drivers to pci_alloc_irq_vectors from Christoph"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (188 commits)
scsi: megaraid_sas: handle dma_addr_t right on 32-bit
scsi: megaraid_sas: array overflow in megasas_dump_frame()
scsi: snic: switch to pci_irq_alloc_vectors
scsi: megaraid_sas: driver version upgrade
scsi: megaraid_sas: Change RAID_1_10_RMW_CMDS to RAID_1_PEER_CMDS and set value to 2
scsi: megaraid_sas: Indentation and smatch warning fixes
scsi: megaraid_sas: Cleanup VD_EXT_DEBUG and SPAN_DEBUG related debug prints
scsi: megaraid_sas: Increase internal command pool
scsi: megaraid_sas: Use synchronize_irq to wait for IRQs to complete
scsi: megaraid_sas: Bail out the driver load if ld_list_query fails
scsi: megaraid_sas: Change build_mpt_mfi_pass_thru to return void
scsi: megaraid_sas: During OCR, if get_ctrl_info fails do not continue with OCR
scsi: megaraid_sas: Do not set fp_possible if TM capable for non-RW syspdIO, change fp_possible to bool
scsi: megaraid_sas: Remove unused pd_index from megasas_build_ld_nonrw_fusion
scsi: megaraid_sas: megasas_return_cmd does not memset IO frame to zero
scsi: megaraid_sas: max_fw_cmds are decremented twice, remove duplicate
scsi: megaraid_sas: update can_queue only if the new value is less
scsi: megaraid_sas: Change max_cmd from u32 to u16 in all functions
scsi: megaraid_sas: set pd_after_lb from MR_BuildRaidContext and initialize pDevHandle to MR_DEVHANDLE_INVALID
scsi: megaraid_sas: latest controller OCR capability from FW before sending shutdown DCMD
...
MPI2 controllers sometimes got lost (i.e. disappear from
/sys/bus/pci/devices) if ASMP is enabled.
Signed-off-by: Slava Kardakov <ojab@ojab.ru>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=60644
Cc: <stable@vger.kernel.org>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The firmware or device, possibly under a heavy I/O load, can return on a
partial unaligned boundary. Scsi-ml expects these requests to be
completed on an alignment boundary. Scsi-ml blindly requeues the I/O
without checking the alignment boundary of the I/O request for the
remaining bytes. This leads to errors, since devices cannot perform
non-aligned read/write operations.
This patch fixes the issue in the driver. It aligns unaligned
completions of FS requests, by truncating them to the nearest alignment
boundary.
[mkp: simplified if statement]
Reported-by: Mauricio Faria De Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated driver version to "15.100.00.00"
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due existence of loop in the IO path our HBA will receive heavy IOs and
also as driver is not updating the Reply Post Host Index frequently, So
there will be a high chance that our Firmware unable to find any free
entry in the Reply Post Descriptor Queue (i.e. Queue overflow occurs)
and can observe 0x2100 firmware fault. So to fix this, we have defined
a thresh hold value. After continuously processing this thresh hold
number of reply descriptors driver will update the Reply Descriptor Host
Index so that this thresh hold number of reply descriptors entries will
be freed and these entries will be available for firmware and we won't
observe this Firmware fault. We have defined this threshold value as
1/3rd of the hba queue depth.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Small glitch/degraded performance in Crusader is improved with SAS
drives by removing unnecessary spinlocks while clearing scsi command in
drivers internal lookup table.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver processes the event MPI26_EVENT_ACTIVE_CABLE_DEGRADED when a
cable is present and is running at a degraded speed (below the SAS3 12
Gb/s rate). Prints added to inform the user that the cable is not
running at optimal speed.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
And require all drivers that want to support BLOCK_PC to allocate it
as the first thing of their private data. To support this the legacy
IDE and BSG code is switched to set cmd_size on their queues to let
the block layer allocate the additional space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
mpt3sas has a firmware failure where it can only handle one pass through
ATA command at a time. If another comes in, contrary to the SAT
standard, it will hang until the first one completes (causing long
commands like secure erase to timeout). The original fix was to block
the device when an ATA command came in, but this caused a regression
with
commit 669f044170
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Tue Nov 22 16:17:13 2016 -0800
scsi: srp_transport: Move queuecommand() wait code to SCSI core
So fix the original fix of the secure erase timeout by properly
returning SAM_STAT_BUSY like the SAT recommends. The original patch
also had a concurrency problem since scsih_qcmd is lockless at that
point (this is fixed by using atomic bitops to set and test the flag).
[mkp: addressed feedback wrt. test_bit and fixed whitespace]
Fixes: 18f6084a98 (mpt3sas: Fix secure erase premature termination)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reported-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for request iopriority handling in the mpt3sas
layer. This works only when a ATA device is behind the SATL. The ATA
device also has to indicate that it supports command priorities in the
identify information that is pulled from the SATL.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
While issuing any ATA passthrough command to firmware the driver will
block the device. But it will unblock the device only if the I/O
completes through the ISR path. If a controller reset occurs before
command completion the device will remain in blocked state.
Make sure we unblock the device following a controller reset if an ATA
passthrough command was queued.
[mkp: clarified patch description]
Cc: <stable@vger.kernel.org> # v4.4+
Fixes: ac6c2a93bd07 ("mpt3sas: Fix for SATA drive in blocked state, after diag reset")
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a work around for a bug with LSI Fusion MPT SAS2 when perfoming
secure erase. Due to the very long time the operation takes, commands
issued during the erase will time out and will trigger execution of the
abort hook. Even though the abort hook is called for the specific
command which timed out, this leads to entire device halt
(scsi_state terminated) and premature termination of the secure erase.
Set device state to busy while ATA passthrough commands are in progress.
[mkp: hand applied to 4.9/scsi-fixes, tweaked patch description]
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fixes, minor spelling mistakes in comments and in a KERN_INFO
message.
[mkp: fixed spelling mistake in patch description]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use le16_to_cpu only for accessing two byte data provided by controller.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support Atomic Request Descriptors for Ventura/SAS35 devices.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An UNMAP command on a PI formatted device will leave the Logical Block
Application Tag and Logical Block Reference Tag as all F's (for those LBAs
that are unmapped). To avoid IO errors if those LBAs are subsequently read
before they are written with valid tag fields, the MPI SCSI IO requests
need to set the EEDPFlags element EEDP Escape Mode field, Bits [7:6]
appropriately. A value of 2 should be set to disable all PI checks if the
Logical Block Application Tag is 0xFFFF for PI types 1 and 2. A value
of 3 should be set to disable all PI checks if the Logical Block
Application Tag is 0xFFFF and the Logical Block Reference Tag is
0xFFFFFFFF for PI type 3.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For SAS35 devices MSIX vectors are inceased to 128 from 96. To support this
Reply post host index register count is increased to 16. Also variable
msix96_vector is replaced with combined_reply_queue and variable
combined_reply_index_count is added to set different values for SAS3 and
SAS35 devices.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added Device ID's for SAS35 devices (Ventura, Crusader, Harpoon &
Tomcat) and updated mpi header file for the same. Also added
"is_gen35_ioc" to MPT3SAS_ADAPTER structure for identifying SAS35 adapters.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removing macro "MPT_DEVICE_TLR_ON" defined in header file as its unused
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When device missing event arrives, device_remove_in_progress bit will be
set and hence driver has to stop sending IOCTL commands.Now the check has
been added in IOCTL path to test device_remove_in_progress bit is set, if
so then IOCTL will be failed printing failure message.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No. of MSIX vectors supported = min (Total no. of CPU cores,
MSIX vectors supported by card)
when RDPQ is disabled "max_msix_vectors" module parameter which was
declared as global was set to '8' and hence if there are more than one card
in system among which if RDPQ disabled card is enumerated first then only 8
MSIX vectors was getting enabled for all the cards(including RDPQ enabled
card,which can support more than 8 MSIX vectors).
Used local variable instead of global variable ,if RDPQ is disabled this
local variable is set to '8' else it is set to "max_msix_vectors" (by
default this is set to -1, whose value can be set by user during driver
load time).So now regardless of whether RDPQ disabled card is enumerated
first or RDPQ enabled card is enumerated first , MSIX vectors enabled
depends on the cards capability.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return value and Device_handle Arguments passed in correct order
to match with its format string.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While merging mpt3sas & mpt2sas code, we added the is_warpdrive check
condition on the wrong line
---------------------------------------------------------------------------
scsih_target_alloc(struct scsi_target *starget)
sas_target_priv_data->handle = raid_device->handle;
sas_target_priv_data->sas_address = raid_device->wwid;
sas_target_priv_data->flags |= MPT_TARGET_FLAGS_VOLUME;
- raid_device->starget = starget;
+ sas_target_priv_data->raid_device = raid_device;
+ if (ioc->is_warpdrive)
+ raid_device->starget = starget;
}
spin_unlock_irqrestore(&ioc->raid_device_lock, flags);
return 0;
------------------------------------------------------------------------------
That check should be for the line sas_target_priv_data->raid_device =
raid_device;
Due to above hunk, we are not initializing raid_device's starget for
raid volumes, and so during raid disk deletion driver is not calling
scsi_remove_target() API as driver observes starget field of
raid_device's structure as NULL.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: <stable@vger.kernel.org> # v4.4+
Fixes: 7786ab6aff ("mpt3sas: Ported WarpDrive product SSS6200 support")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (hpsa, be2iscsi,
hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa called smartpqi
for which a driver is added, there's some cleanup work of the ibm vscsi target
and updates to libfc, plus a whole host of minor fixes and updates and finally
the removal of several ISA drivers which seem not to have been used for years.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cyTO
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (hpsa,
be2iscsi, hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa
called smartpqi for which a driver is added, there's some cleanup work
of the ibm vscsi target and updates to libfc, plus a whole host of
minor fixes and updates and finally the removal of several ISA drivers
which seem not to have been used for years"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (173 commits)
scsi: mvsas: Mark symbols static where possible
scsi: pm8001: Mark symbols static where possible
scsi: arcmsr: Simplify user_len checking
scsi: fcoe: fix off by one in eth2fc_speed()
scsi: dtc: remove from tree
scsi: t128: remove from tree
scsi: pas16: remove from tree
scsi: u14-34f: remove from tree
scsi: ultrastor: remove from tree
scsi: in2000: remove from tree
scsi: wd7000: remove from tree
scsi: scsi_dh_alua: Fix memory leak in alua_rtpg()
scsi: lpfc: Mark symbols static where possible
scsi: hpsa: correct call to hpsa_do_reset
scsi: ufs: Get a TM service response from the correct offset
scsi: ibmvfc: Fix I/O hang when port is not mapped
scsi: megaraid_sas: clean function declarations in megaraid_sas_base.c up
scsi: ipr: Remove redundant messages at adapter init time
scsi: ipr: Don't log unnecessary 9084 error details
scsi: smartpqi: raid bypass lba calculation fix
...
In _scsih_io_done() we test if the ioc->logging_level does _not_ have
the MPT_DEBUG_REPLY bit set and if it hasn't we print the debug
messages. This unfortunately is the wrong way around.
Note, the actual bug is older than af0094115 but this commit removed the
CONFIG_SCSI_MPT3SAS_LOGGING Kconfig option which hid the bug.
Fixes: af0094115 'mpt2sas, mpt3sas: Remove SCSI_MPTXSAS_LOGGING entry from Kconfig'
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial non-functional changes for a couple annoying things:
1) Functions local to files are not declared static, which is
frustrating when reading the code because it's non-obvious at first
glance what's actually called from other files.
2) Set-but-unused variables abound, presumably to mask -Wunused-result
errors in the past. None of these are flagged today though (with one
exception noted below), so remove them.
Fixing (2) exposed the fact that we improperly ignore the return value
of scsi_device_reprobe() in _scsih_reprobe_lun(). Fixing the calling
code to deal with the potential error is non-trivial, so for now just
WARN().
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With the exception of a single call to wait_for_doorbell_int(), all this
conditional sleeping code is dead. So delete it.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This flag that conditionally acquires the mutex is confusing and prone
to bugginess: refactor it into two separate function calls, and make the
unlocked one complain if it's called outside the mutex.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We blindly trust the hardware to give us NUL-terminated strings, which
is a bad idea because it doesn't always do that. For example:
[ 481.184784] mpt3sas_cm0: enclosure level(0x0000), connector name( \x3)
In this case, connector_name is four spaces. We got lucky here because
the 2nd byte beyond our character array happens to be a NUL. Fix this by
explicitly writing '\0' to the end of the string to ensure we don't run
off the edge of the world in printk().
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The _scsih_pci_mmio_enabled called if scsih_pci_error_detected returns
PCI_ERS_RESULT_CAN_RECOVER, at this point, read/write to the device
still works, no need to reset slot.
Or the mpt3sas_base_map_resources in scsih_pci_slot_reset will fail,
and iounamp ioc->chip, then we will meet issue when read ioc->chip
in mpt3sas_base_get_iocstate from _base_fault_reset_work.
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If _scsih_sas_host_add's call to mpt3sas_config_get_sas_iounit_pg0
fails, ioc->sas_hba.parent_dev may be left uninitialized. A later
device probe could invoke mpt3sas_transport_port_add which will call
sas_port_alloc_num [scsi_transport_sas] with a NULL parent_dev pointer.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _scsih_sas_host_add, the number of HBA phys are determined and then
later used to allocate an array of struct _sas_phy's. If the routine
sets ioc->sas_hba.num_phys, but then fails to allocate the
ioc->sas_hba.phy array (by kcalloc error or other intermediate
error/exit path), ioc->sas_hba is left in a dangerous state: all readers
of ioc->sas_hba.phy[] do so by indexing it from 0..ioc->sas_hba.num_phys
without checking that the space was ever allocated.
Modify _scsih_sas_host_add to set ioc->sas_hba.num_phys only after
successfully allocating ioc->sas_hba.phy[].
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are some missing curly braces on this if statement, so we end up
printing when we shouldn't.
Fixes: a470a51cd6 ('mpt3sas: Handle active cable exception event')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaced mpt3sas_base_flush_reply_queues() with
mpt3sas_base_sync_reply_irqs(),as mpt3sas_base_flush_reply_queues()
skips over reply queues that are currently busy (i.e. being handled by
interrupt processing in another core). If a reply queue is busy, then
call to synchronize_irq()in mpt3sas_base_sync_reply_irqs()make sures the
other core has finished flushing the queue and completed any calls to
the mid-layer scsi_done() routine.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set maximum transfer length per IO on RAID volumes to 4MB by setting
VD's queue's max_sector to 8192.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bump mpt3sas driver version from 12.100.00.00 to 13.100.00.00
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified driver code to use scsi_prot_ref_tag() API instead of
scsi_get_lba(), while initializing reference tag field in the CDB.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In-order to handle this 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
driver need to follow below steps,
1. Unmask the 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
so that FW can notify this event to host driver.
2. After receiving this event, add this event to AEN event queue,
for notifying this event to applications.
3. Then Print below message in kernel logs if the event data's reason
code is zero,
"Currently an active cable with ReceptacleID <ID_Value> cannot be powered
and devices connected to this active cable will not be seen. This active
cable requires <PowerValue_in_mW> of power"
This event is only for Intruder/Cutlass HBAs.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated MPI version and MPI header files.
ChangeList:
* Added SATADeviceWaitTime to SAS IO Unit Page 4
* Added EEDPObservedValue added to SCSI IO Reply message
* Added MPI2_EVENT_ACTIVE_CABLE_EXCEPTION and
MPI26_EVENT_DATA_ACTIVE_CABLE_EXCEPT
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware events are queued up using the fw_event_work's struct work, not
its delayed_work member. The initial driver for SAS2 controllers had
handled firmware reset using the rescan barrier and was later redesigned
through "mpt2sas: [Resend] Host Reset code cleanup". The delayed_work
variables are now unused and may provoke CONFIG_DEBUG_OBJECTS_TIMERS
"assert_init not available" false warnings in
_scsih_fw_event_cleanup_queue.
Cleanup fw_event_work's unused entries, update its kerneldoc, and
update _scsih_fw_event_cleanup_queue accordingly.
Fixes: 146b16c807 (mpt3sas: Refcount fw_events and fix unsafe list usage)
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'struct timeval' will have its tv_sec value overflow on 32-bit systems
in year 2038 and beyond. This patch replaces the use of struct timeval
for computing mpi_request.TimeStamp, and instead uses ktime_t which
provides 64-bit seconds value. The timestamp computed remains
unaffected (milliseconds since Unix epoch).
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _base_make_ioc_operational(), we walk ioc->reply_queue_list and pull
a pointer out of successive elements of ioc->reply_post[] for each entry
in that list if RDPQ is enabled.
Since the code pulls the pointer for the next iteration at the bottom of
the loop, it triggers the a KASAN dump on the final iteration:
BUG: KASAN: slab-out-of-bounds in _base_make_ioc_operational+0x47b7/0x47e0 [mpt3sas] at addr ffff880754816ab0
Read of size 8 by task modprobe/305
<snip>
Call Trace:
[<ffffffff81dfc591>] dump_stack+0x4d/0x6c
[<ffffffff814c9689>] print_trailer+0xf9/0x150
[<ffffffff814ceda4>] object_err+0x34/0x40
[<ffffffff814d1231>] kasan_report_error+0x221/0x530
[<ffffffff814d1673>] __asan_report_load8_noabort+0x43/0x50
[<ffffffffa0043637>] _base_make_ioc_operational+0x47b7/0x47e0 [mpt3sas]
[<ffffffffa0049a51>] mpt3sas_base_attach+0x1991/0x2120 [mpt3sas]
[<ffffffffa0053c93>] _scsih_probe+0xeb3/0x16b0 [mpt3sas]
[<ffffffff81ebd047>] local_pci_probe+0xc7/0x170
[<ffffffff81ebf2cf>] pci_device_probe+0x20f/0x290
[<ffffffff820d50cd>] really_probe+0x17d/0x600
[<ffffffff820d56a3>] __driver_attach+0x153/0x190
[<ffffffff820cffac>] bus_for_each_dev+0x11c/0x1a0
[<ffffffff820d421d>] driver_attach+0x3d/0x50
[<ffffffff820d378a>] bus_add_driver+0x44a/0x5f0
[<ffffffff820d666c>] driver_register+0x18c/0x3b0
[<ffffffff81ebcb76>] __pci_register_driver+0x156/0x200
[<ffffffffa00c8135>] _mpt3sas_init+0x135/0x1000 [mpt3sas]
[<ffffffff81000423>] do_one_initcall+0x113/0x2b0
[<ffffffff813caa5a>] do_init_module+0x1d0/0x4d8
[<ffffffff81273909>] load_module+0x6729/0x8dc0
[<ffffffff81276123>] SYSC_init_module+0x183/0x1a0
[<ffffffff8127625e>] SyS_init_module+0xe/0x10
[<ffffffff828fe7d7>] entry_SYSCALL_64_fastpath+0x12/0x6a
Fix this by pulling the value at the beginning of the loop.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jens Axboe <axboe@fb.com>
Acked-by: Chaitra Basappa <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling synchronize_irq() right before free_irq() is quite useless. On
one hand the IRQ can easily fire again before free_irq() is entered, on
the other hand free_irq() itself calls synchronize_irq() internally (in
a race condition free way), before any state associated with the IRQ is
freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Deallocate resources before reallocating of the same in retry_allocation
path of _base_allocate_memory_pools()
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removed cpumask_clear as it is not required for zalloc_cpumask_var and
free free_cpumask_var before freeing reply_q.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bump mpt3sas driver version from 09.102.00.00 to 12.100.00.00
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Track msix of each IO and use the same msix for issuing abort to timed
out IO. With this driver will process IO's reply first followed by TM.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated MPI version and MPI header files.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support for configurable Chain Frame Size. Calculate the
Chain Message Frame size from the IOCMaxChainSegementSize (iocfacts).
Applicable only for mpt3sas/SAS3.0 HBA's.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Module parameter to enable/disable configuring affinity hint for msix
vector. SMP affinity feature can be enabled/disabled by setting module
parameter "smp_affinity_enable" to 1/0. By default this feature is
enabled. (smp_affinity_enable = 1 enabled).
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver assumes HighPriority credit as part of Global credit. But,
Firmware treats HighPriority credit value and global cedits as two
different values. Changed host queue algorithm to treat global credits
and highPriority credits as two different values.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Never block the SEP device (i.e. Never invoke the
scsi_internal_device_block() API for SEP device) even for the delay not
responding events. Blocking the SEP device will create a deadlock while
adding any device to the OS.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1.Wrong size of argument is being passed
The size of struct being passed as an argument to memset func and area of
memory being pointed by an instance of struct in memset func should be of
same structure type.
2.Dereference null return value
3.Array compared against '0'
Check whether value pointed by particular index of an array is null or not
in "if" statement.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As driver was using MPI SGL while framing the SMP Passthrough request
message due to which firmware unable to post the Reply Data in the host
memory and timeout is observed for this SMP Passthrough request message
and so unable to perform phy disable operation.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated hardware description headers with MPI v2.6 and
mpt3sas_pci_table[] with vendor_ids, device_ids of Cutlass and Intruder
HBA which have support for 4 ports.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It might happen that we try to free an already freed pointer.
Reported-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Chaitra P B <chaitra.basappa@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The non-PCI builds of the O day test project are failing:
On Thu, 2015-12-03 at 05:02 +0800, kbuild test robot wrote:
> warning: (SCSI_MPT2SAS) selects SCSI_MPT3SAS which has unmet direct
> dependencies (SCSI_LOWLEVEL && PCI && SCSI)
The problem is that select and depend don't interact because Kconfig doesn't
have a SAT solver, so depend picks up dependencies and select does onward
selects, but select doesn't pick up dependencies. To fix this, we need to add
the correct dependencies to the MPT2SAS option like this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: b840c3627b
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The mpt2sas driver was recently folded into mpt3sas to reduce code
duplication.
To avoid problems for people that only have CONFIG_SCSI_MPT2SAS in their
.config we introduce a dummy option that will select MPT3SAS if MPT2SAS
was previously enabled.
This is a temporary measure and we will deprecate this config option in
4.6.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com>
CC: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag in MPI SCSI IO request
message, check whether TLR is enabled on the drive using
'sas_is_tlr_enabled' API.
Actually in the driver code, driver is using below API's
1. sas_enable_tlr() - to enable the TLR
2. sas_disable_tlr() - to disable the TLR
3. sas_is_tlr_enabled() - to check whether TLR is enabled or not.
but in scsih_qcmd() we have missed to use sas_is_tlr_enabled() API,
instead we checking for TLR bit from flag field of driver's 'struct
MPT3SAS_DEVIC' structure. which is corrected with this patch.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After merging the scsi tree, today's linux-next build (powerpc
allyesconfig) failed like this:
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0:
drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function '_scsih_io_done':
drivers/scsi/mpt3sas/mpt3sas_base.h:1414:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_get': function body not available
mpt3sas_scsi_direct_io_get(struct MPT3SAS_ADAPTER *ioc, u16 smid);
^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4448:6: error: called from here
if (mpt3sas_scsi_direct_io_get(ioc, smid) &&
^
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0:
drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available
mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io);
^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here
mpt3sas_scsi_direct_io_set(ioc, smid, 0);
^
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:5
9:0:
drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available
mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io);
^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here
mpt3sas_scsi_direct_io_set(ioc, smid, 0);
^
Presumably caused by commit
c84b06a48c ("mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Bump mpt3sas driver version to 09.102.00.00
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified the mpt3sas driver to have a single driver module which
supports both SAS 2.0 & SAS 3.0 HBA devices.
* Added SAS 2.0 HBA device IDs to the mpt3sas_pci_table pci table.
* Created two separate SCSI host templates for SAS2 and SAS3 HBAs so
that, during the driver load time driver can use corresponding host
template(based the pci device ID) while registering a scsi host
adapter instance for that pci device.
* Registered two IOCTL devices, mpt2ctl is for SAS2 HBAs & mpt3ctl for
SAS3 HBAs. Also updated the code to make sure that mpt2ctl device
processes only those ioctl cmds issued for the SAS2 HBAs and mpt3ctl
device processes only those ioctl cmds issued for the SAS3 HBAs.
* Added separate indexing for SAS2 and SAS3 HBAs.
* Replaced compile time check 'MPT2SAS_SCSI' to run time check
'hba_mpi_version_belonged' whereever needed.
* Aliased this merged driver to mpt2sas using MODULE_ALIAS.
* Moved global varaible 'driver_name' to per adapter instance variable.
* Created two raid function template and used corresponding raid
function templates based on the run time check
'hba_mpi_version_belonged'.
* Moved mpt2sas_warpdrive.c file from mpt2sas to mpt3sas folder and
renamed it as mpt3sas_warpdrive.c.
* Also renamed the functions in mpt3sas_warpdrive.c file to follow
current driver function name convention.
* Updated the Makefile to build mpt3sas_warpdrive.o file for these
WarpDrive-specific functions.
* Also in function mpt3sas_setup_direct_io(), used sector_div() API
instead of division operator (which gives compilation errors on 32 bit
machines).
* Removed mpt2sas files, mpt2sas directory & mpt3sas_module.c file.
* Added module parameter 'hbas_to_enumerate' which permits using this
merged driver as a legacy mpt2sas driver or as a legacy mpt3sas
driver.
Here are the available options for this module parameter:
0 - Merged driver which enumerates both SAS 2.0 & SAS 3.0 HBAs
1 - Acts as legacy mpt2sas driver, which enumerates only SAS 2.0 HBAs
2 - Acts as legacy mpt3sas driver, which enumerates only SAS 3.0 HBAs
* Removed mpt2sas entries from SCSI's Kconfig and Makefile files.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bump the mpt2sas driver version to 20.102.00.00 and
Bump the mpt3sas driver version to 9.101.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
setpci reset on nytro warpdrive card along with sysfs access and cli
ioctl access resulted in kernel oops
1. pci_access_mutex lock added to provide synchronization between IOCTL,
sysfs, PCI resource handling path
2. gioc_lock spinlock to protect list operations over multiple
controllers
This patch is ported from commit 6229b414b3 ("mpt2sas: setpci reset
kernel oops fix").
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added OEM Gen2 PnP ID branding names from mpt2sas driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fw_event_work struct is concurrently referenced at shutdown. Add a
refcount to protect it and refactor the code to use it.
Additionally, refactor _scsih_fw_event_cleanup_queue() such that it no
longer iterates over the list without holding the lock since
_firmware_event_work() concurrently deletes items from the list.
This patch is ported from commit 008549f6e8 ("mpt2sas: Refcount
fw_events and fix unsafe list usage"). These changes are also required
for mpt3sas.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_device objects can be referenced concurrently throughout the driver.
We need a way to make sure threads can't delete them out from under each
other. This patch adds the refcount and refactors the code to use it.
Additionally, we cannot iterate over the sas_device_list without holding
the lock or we risk corrupting random memory if items are added or
deleted as we iterate. This patch refactors _scsih_probe_sas() to use
the sas_device_list in a safe way.
This patch is ported from the following mpt2sas driver commit
d224fe0d60 ("mpt2sas: Refcount sas_device objects and fix unsafe list
usage").
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A new sysfs shost attribute called "BMR_status" is implemented to report
Backup Rail Monitor status.
This attribute is located in:
/sys/class/scsi_host/host#/BMR_status
When reading this adapter attribute, the driver will output the state of
GPIO[24]. It returns "0" if BMR is healthy and "1" for failure.
If it returns an empty string then it means that there was an error
while obtaining the BMR status. Check dmesg for what error has occurred.
This sysfs shost attribute is mainly for WarpDrive controllers.
This commit is a port of 6c265660c2 ("mpt2sas: Provide sysfs attribute
to report Backup Rail Monitor Status").
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ported the following list of WarpDrive-specific patches:
1. commit 0bdccdb0a0 ("mpt2sas: WarpDrive
New product SSS6200 support added")
2. commit 82a4525812 ("mpt2sas: WarpDrive
Infinite command retries due to wrong scsi command entry in MPI
message")
3. commit ba96bd0b1d ("mpt2sas: Support
for greater than 2TB capacity WarpDrive")
4. commit 4da7af9494 ("mpt2sas: Do not
retry a timed out direct IO for Warpdrive")
5. commit daeaa9df92 ("mpt2sas: Avoid type
casting for direct I/O commands").
Also set the mpt2_ioctl_iocinfo adapter_type to:
1. MPT3_IOCTL_INTERFACE_SAS3 for Gen3 HBAs
2. MPT2_IOCTL_INTERFACE_SAS2_SSS6200 for Warp Drive
3. MPT2_IOCTL_INTERFACE_SAS2 for other Gen2 HBAs
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch stops the driver to invoke kthread (which remove the dead
ioc) for some time while EEH recovery has started.
This patch is a port of commit b4730fb6e5 ("mpt2sas: fix for driver
fails EEH, recovery from injected pci bus error")'.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Do not enable MSI-X vectors for SAS2008 B0 controllers
2. Enable a single MSI-X vector for the following controller:
a. SAS2004
b. SAS2008
c. SAS2008_1
d. SAS2008_2
e. SAS2008_3
f. SAS2116_1
g. SAS2116_2
3. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
for Gen3 Invader/Fury C0 and above revision HBAs
4. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
for all Intruder and Cutlass HBAs
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid sending PHYDISK_HIDDEN RAID action requests to SAS2 controllers
since they don't support it.
Also enable fast_path only for SAS3 HBAs.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gen2 HBAs use MPI scatter-gather lists whereas Gen3 HBAs use IEEE
scatter-gather lists. Modify the common code part in such a way that it
will build IEEE SGL tables for Gen3 HBAs and MPI SGL tables for Gen2
HBAs.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there is a logging level option provided for each of our
drivers in the kernel configuration utility. Users can enable this
option to get more verbose information. By default it is enabled.
Only when this option is enabled will the functions which display the
required information get compiled in.
As we are merging the both drivers we can no longer provide this
configuration option. Remove the SCSI_MPTXSAS_LOGGING entry from Kconfig
and unconditionally enable logging (by removing the #ifdef
CONFIG_SCSI_MPT3SAS_LOGGING preprocessor check conditions) so that all
functions which are defined to display more verbose information get
compiled in.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Use 'hba_mpi_version_belonged' IOC varable to uniquely identify each
individual generation driver functionality at runtime.
2. Declare global variable 'driver_name' and use this variable while
reserving PCI regions and while allocating the IRQs.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Create a mpt2sas_module.c file for mpt2sas where GEN2 HBA devices
register with PCI, SML, IOCTL subsystems.
2. Updated the Makefile to use the object files from mpt3sas folder.
3. Defined a compilation flag SCSI_MPT2SAS which can be used to not
include those sections of code from mpt3sas driver which are not
required for mpt2sas driver.
4. Inherited automatic diag buffer feature from mpt3sas driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Created a mpt3sas_module.c file for mpt3sas driver where it can register
SAS3 HBA devices with PCI, SML, IOCTL subsystems. Also removed the
corresponding interfaces from mpt3sas_scsih.c file.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Added mpt2sas driver related macros in mpt3sas header files
2. Made scsi host's, raid class', pci's, ioctl's callback functions
global so that both drivers can use them.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Issue: When the disks are getting discovered and assigned device
handles by the kernel, a device block followed by an unblock
(due to broadcast primitives) issued by the driver is
interspersed by the kernel changing the state of the device.
Therefore the unblock by the driver results in a no operation
within the kernel API.
To fix this one, the below patch checks the return of the unblock API
and performs a block followed by an unblock to unfreeze the block
layer's I/O queue. Sufficient checks and prints are also added in the
driver to identify this condition caused by the kernel.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Added dma_mapping_error() API after mapping an address with dma_map_single()
API. Otherwise when CONFIG_DMA_API_DEBUG is enabled in the kernel, then it
complains about mpt3sas driver not calling dma_mapping_error after mapping an
address with dma_map_single
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Created a thread using alloc_ordered_workqueue() API in order to process
the works from firmware Work-queue sequentially instead of
create_singlethread_workqueue() API.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
scsi_dma_map API will return a negative value (i.e. -ENOMEM)
if DMA mapping of sg lists fails and zero if the sg list in the
SCSI cmd is NULL. But drivers doesn't handled sg list DMA mapping
failure case properly.
So, Updated the code to return host busy error status to SCSI MID Layer(SML),
when DMA mapping of scatter gather list fails for a SCSI command.
So that SML will retry this SCSI cmd after some time.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
For any SCSI command, if the driver receives
IOC status = SCSI_IOC_TERMINATED and log info = 0x32010081 then
that command will be completed with DID_RESET host status.
The definition of this log info value is
"Virtual IO has failed and has to be retried".
Firmware will provide this log info value with IOC Status
"SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume)
is pulled and pushed back within some minimal delay.
With this log info value, firmware informs the driver to retry the
failed IO command infinite times, so to provide some time for the
firmware to discover the reinserted drive successfully instated of
just retrying failed command for five times(doesn't giving enough
time for firmware to complete the drive discovery) and failing the
IO permanently even though drive came back successfully.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Below are the new changes to MPI 2.5 Rev K(2.5.6) specification and 2.00.35
header files
1) Added a minimum size requirement for target mode command buffers.
2) Added MinMSIxIndex and MaxMSIxIndex fields to CommandBufferPostBase
Request.
3) For BIOS Page 1, added SSUTimeout field, and added Product Name String
Format bits to the BiosOptions field
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Following is the change set,
1. Added more defines for the BiosOptions field of MPI2_CONFIG_PAGE_BIOS_1.
2. Added MPI2_TOOLBOX_CLEAN_BIT26_PRODUCT_SPECIFIC definition.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This Patch will provide more details of the devices such as slot number,
enclosure logical id, enclosure level & connector name in the following
scenarios,
- When end device is added in the topology,
- When the end device is removed from the setup,
- When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during
error handling,
- When any command to the device fails with Sense key Hardware error or Medium
error or Unit Attention,
- When firmware returns device error or device not ready status for the end
device,
- When a Predicted fault is detected on an end device.
This information can be used by the user to identify the location of the
desired drive in the topology.
Driver will get these information by reading the sas device page0.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Update MPI 2.5 Release: MPI 2.5 Rev I (2.5.4) specification and 2.00.33 header
files
Below is the change set from the MPI specification for I Rev
1) Added Base Enclosure Level bit to the Flags field of Manufacturing Page 7.
2) Updated description of the MaxTargetPortConnectTime field of SAS IO Unit
Page 1.
3) Added EnclosureLevel and ConnectorName fields to SAS Device Page 0. Also,
added EnclosureLevel and ConnectorName Valid bit to the Flags field.
4) Added EnclosureLevel field to SAS Enclosure Page 0. Also, added
EnclosureLevel Valid bit to the Flags field.
5) Added value for BIOS image to HashImageType.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
During hot-plugging of a disk(having a flaky link), the disk addition
stops and any further disk addition or removal doesn't happen on that
controller.
This is because, when driver receives DELAY_NOT_RESPONDING event for a disk
while it is undergoing addition at the SCSI Transport layer, the driver
would block the I/O to that disk resulting in a deadlock. i.e the disk
addition work couldn't be completed at the SCSI Transport Layer as it
can't send any I/Os (such as Inquiry, Report LUNs etc) to the disk as
I/Os are blocked to this drive. Also any subsequent device removal
(TARGET_NOT_RESPONDING) or link update(RC_PHY_CHANGED) event couldn't be
processed as they are in the queue to get processed after disk addition
event.
Description of Change:
Don't block the drive when drive addition is under the control of SML.
So that SML won't be blocked of issuing the device dicovery commands
(such as Inquiry, Report LUNs etc).
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Driver initialization fails if driver tries to send IOC facts request message
when the IOC is in reset or in a fault state.
This patch will make sure that
1.Driver to send IOC facts request message only if HBA is in operational or
ready state.
2.If IOC is in fault state, a diagnostic reset would be issued.
3.If IOC is in reset state then driver will wait for 10 seconds to exit out
of reset state. If the HBA continues to be in reset state, then the HBA
wouldn't be claimed by the driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to
up-to 96.
Following are changes that are done in this patch
1. This feature is enabled only for SAS3 C0 and higher revision cards and also
only when reply post free queue count is greater than 8.
2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces
are used. MSI-X index numbered from 0 to 7 use the first
SupplementalReplyPostHostIndex system interface to update its corresponding
ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the
second SupplementalReplyPostHostIndex system interface and so on. These 12
SuppementalReplyPostHostIndex system interfaces address are saved in the array
replyPostRegisterIndex[].
3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X
vectors. So MSIxIndex field in these register must contain a value between 0
and 7.
4. After processing the reply descriptors from a reply post free queues then
update the new reply post host index value in ReplyPostHostIndex field and
(msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex
register. The Address of this SupplementalReplyPostHostIndex register is
retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Driver crashes if the BIOS do not set up at least one
memory I/O resource. This failure can happen if the device is too
slow to respond during POST and is missed by the BIOS, but Linux
then detects the device later in the boot process.
Based on a patch from Timothy Pearson <tpearson@raptorengineeringinc.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Added a support to set cpu affinity mask for each MSIX vector enabled
by the HBA. So that, running the irqbalancer will balance interrupts among
the cpus.
Change_set:
1. Added affinity_hint varable of type cpumask_var_t in adapter_reply_queue
structure. And allocated a memory for this varable by calling
alloc_cpumask_var.
2. Call the API irq_set_affinity_hint for each MSIx vector to affiniate it
with calculated cpus at driver inilization time.
3. While freeing the MSIX vector, call this same API to release the cpu
affinity mask for each MSIx vector by providing the NULL value in
cpumask argument.
4. then call the free_cpumask_var API to free the memory allocated in step 2.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Copyright, Trademark & Confidentiality legal statements throughout the
source code changed from LSI to Avago.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Change Set:
1. Extended the upper boundary restriction for the module parameter
max_sgl_entries. Earlier, the max_sgl_entries was capped at the
SCSI_MAX_SG_SEGMENTS kernel definition. With this change, the user
would be able to set the max_sgl_entries to any value which is
greater than SCSI_MAX_SG_SEGMENTS and less than the minimum of
SCSI_MAX_SG_CHAIN_SEGMENTS & hardware limit (Calculated using
IOCFacts's MaxChainDepth).
2. Added a print for the message log whenever the user sets the
max_sgl_entries to a value greater than SCSI_MAX_SG_SEGMENTS to
warn about the kernel definition overriding.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When a flaky disk is there in a topology then during driver load,
discovery related I/O times out; which results in SCSI error recovery
initiating host reset and then the controller won't see any disk.
In this patch, The driver would return FAILED status to the host reset
initiated due to discovery related I/O timeout if ioc->is_driver_loading
is set. This flag would be set until we exit out of scsih_scan_finished().
i.e.
During device discovery if one of the disk is flaky
(which responds to some discovery commands and doesn't respond to some)
the driver wouldn't perform host reset for discovery related I/O timeout.
Instead it would return Failure for the host reset resulting in the
flaky disk getting removed by the SCSI Mid layer,
so other disks would be added correctly.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch will log a message when driver receives "Temperature Threshold
exceeded" event from any temperature sensor.
The message will look similar to like:
mpt3sas0: Temperature Threshold flags a b c d exceeded for Sensor: x !!!
mpt3sas0: Current Temp In Celsius: y
where a b c d are threshold flags 0 1 2 3
Change_set:
1. Get the number of sensor count of this IOC by reading IO Unit page 8 at
driver initialization time.
2. Also unmask the Temperature Threshold Event at driver initialization
time
3. Whenever a MPI2_EVENT_TEMP_THRESHOLD event is received from the
firmware, then print the sensor number, the maximum threshold number it
has exceed and the current temperature of this sensor.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The "issue_reset" can be used uninitialized. It should be set to false
at the start.
Also I cleaned up the types a little by using bool.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This reverts commit 963ba22b90
("mpt3sas: Remove phys on topology change")
Reverting the previous mpt3sas drives patch changes,
since we will observe below issue
Issue:
Drives connected Enclosure/Expander will unregister with
SCSI Transport Layer, if any one remove and add expander
cable with in DMD (Device Missing Delay) time period or
even any one power-off and power-on the Enclosure with in
the DMD period.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete. The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Merge two functions, and remove overly verbose debugging output that pokes
into mid-layer internal structures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the ordered_tags field, we haven't been issuing ordered tags based
on it since the big barrier rework in 2010.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Most drivers use exactly the same implementation, so provide it as a
library function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
In _scsih_probe, propagate the return value from scsi_add_host.
In mpt3sas, avoid calling list_del twice if that returns an
error, which causes list_del corruption warnings if an error
is returned.
Tested with blk-mq and scsi-mq patches to properly cleanup
from and propagate blk_mq_init_rq_map errors.
Signed-off-by: Robert Elliott <elliott@hp.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump mpt3sas driver version to 04.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Up to now, Driver allocates a single contiguous block of memory
pool for all reply queues and passes down a single address in the
ReplyDescriptorPostQueueAddress field of the IOC Init Request
Message to the firmware.
When firmware receives this address, it will program each of the
Reply Descriptor Post Queue registers, as each reply queue has its
own register. Thus the firmware, starting from a base address it
determines the starting address of the subsequent reply queues
through some simple arithmetic calculations.
The size of this contiguous block of memory pool is directly proportional
to number of MSI-X vectors and the HBA queue depth. For example higher
MSIX vectors requires larger contiguous block of memory pool.
But some of the OS kernels are unable to allocate this larger
contiguous block of memory pool.
So, the proposal is to allocate memory independently for each
Reply Queue and pass down all of the addresses to the firmware.
Then the firmware will just take each address and program the value
into the correct register.
When HBAs with older firmware(i.e. without RDPQ capability) is used
with this new driver then the max_msix_vectors value would be set
to 8 by default.
Change set in v1:
1. Declared the _base_get_ioc_facts() functions at the beginning of the mpt3sas_base.c file
instead of moving all these functions before mpt3sas_base_map_resources() function
a. _base_wait_for_doorbell_int()
b. _base_wait_for_doorbell_ack()
c. _base_wait_for_doorbell_not_used()
d. _base_handshake_req_reply_wait()
e. _base_get_ioc_facts()
2. Initially set the consistent DMA mask to 32 bit and then change it to 64 bit mask
after allocating RDPQ pools by calling the function _base_change_consistent_dma_mask.
This is to ensure that all the upper 32 bits of RDPQ entries's base address to be same.
3. Reduced the redundancy between the RDPQ and non-RDPQ support in these following functions
a. _base_release_memory_pools()
b. _base_allocate_memory_pools()
c. _base_send_ioc_init()
d. _base_make_ioc_operational()
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Copyright in driver sources is updated for year the 2014.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Below is the change set in MPI2.5 Rev H specification and 2.00.32 header files
1) Added reserved fields to IO Unit Page 7 for future use.
2) Added optional functionality to IOCInit Request so that
the host may specify a separate base address for each
Reply Descriptor Post Queue. IOC support for this is
indicated using a new IOCCapabilities bit in the IOCFacts Reply.
3) Added Toolbox Console Text Display Tool
The host uses the Console Text Display Tool to send a string to
IOC's Console using different console types (eg: UART serial terminal or Ethernet terminal).
4) Firmware images can now be signed using an encrypted hash.
5) Added MPI2_SAS_OP_TRANSMIT_PORT_SELECT_SIGNAL
6) Added more details about configuration page restrictions when Host Based Discovery is enabled
Enabling host based discovery affects the availability of some configuration pages and events.
The SAS Expander, SAS Device, and SAS Enclosure configuration pages are not available from the IOC.
The IOC returns an error status to any Configuration Request message attempting to access these pages.
The IOC does not send the SAS Discovery Event, the SAS Topology Change List Event, or
the SAS Enclosure Device Status Change Event when host based discovery is enabled.
7) Bit 13 of the SAS IO Unit Page 1 ControlFlags field is now obsolete.
It was used to enable limiting direct attached SATA maximum link rate to 1.5 Gbps.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump mpt3sas driver version to 03.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Added code to send an SEP message that turns off the Predictive
Failure LED when a drive is removed (if Predictive Failure LED was turned on).
Added a new flag 'pfa_led_on' per device that tracks the status of Predictive
Failure LED. When the drive is removed, this flag is checked and
sends an SEP message to turn off the respective Predictive Failure LED.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Below is the change set in MPI2.5 Rev G specification and 2.00.31 header files
1) Added SCSIStatusQualifier to SCSI IO Error Reply message.
2) Added ATA Security Freeze Lock to IO Unit Page 1 Flags field.
3) Added Allow Protection Information bit for IR Volume Create.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In _scsih_probe, delay the call to scsi_add_host until the host has been
fully set up.
Otherwise, the default .can_queue value of 1 causes scsi-mq to set the block
layer request queue size to its minimum size, resulting in awful performance.
In _scsih_probe error handling, call mpt3sas_base_detach rather than
scsi_remove_host to properly clean up in reverse order.
In _scsih_remove, call scsi_remove_host earlier to clean up in reverse order.
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@avagotech.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
On systems with a non power-of-two CPU count the existing MSI-X grouping
code failed to distribute interrupts correctly. Rework the code to
handle arbitrary processor counts.
Also remove the hardcoded upper limit on the number of processors so we
can boot on large systems.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Sreekanth Reddy <Sreekanth.reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tack the firmware reply event_data payload to the end of its
corresponding struct fw_event_work allocation. This matches the
convention in the mptfusion driver and simplifies the code.
This avoids the following smatch warning:
drivers/scsi/mpt3sas/mpt3sas_scsih.c:2519
mpt3sas_send_trigger_data_event() warn: possible memory leak of
'fw_event'
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In _scsih_{slave,target}_alloc, an incorrect structure type is passed
to sizeof() when allocating storage for hostdata. Luckily larger
structure types were used, so at least the wrong sizes were safe:
struct scsi_device (1784 bytes) > struct MPT3SAS_DEVICE (24 bytes)
struct scsi_target (760 bytes) > struct MPT3SAS_TARGET (32 bytes)
This fixes the following smatch warnings:
drivers/scsi/mpt3sas/mpt3sas_scsih.c:1166 _scsih_target_alloc()
warn: struct type mismatch 'MPT3SAS_TARGET vs scsi_target'
drivers/scsi/mpt3sas/mpt3sas_scsih.c:1280 _scsih_slave_alloc()
warn: struct type mismatch 'MPT3SAS_DEVICE vs scsi_device'
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that we're using 64-bit LUNs internally we need to increase
the size of max_luns to 64 bits, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Removing the host_lock from the I/O submission path gives a huge
scalability improvement.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Praveen Krishnamoorthy <Praveen.krishnamoorthy@lsi.com>
Acked-by: Sreekanth Reddy <Sreekanth.reddy@lsi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The mpt3sas_scsih_issue_tm() function does not use the 'serial_number'
argument passed to it. Removing it removes the last vestiges of the
scsi_cmnd's serial_number field from this driver.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Praveen Krishnamoorthy <Praveen.krishnamoorthy@lsi.com>
Acked-by: Sreekanth Reddy <Sreekanth.reddy@lsi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull core block IO changes from Jens Axboe:
"The major piece in here is the immutable bio_ve series from Kent, the
rest is fairly minor. It was supposed to go in last round, but
various issues pushed it to this release instead. The pull request
contains:
- Various smaller blk-mq fixes from different folks. Nothing major
here, just minor fixes and cleanups.
- Fix for a memory leak in the error path in the block ioctl code
from Christian Engelmayer.
- Header export fix from CaiZhiyong.
- Finally the immutable biovec changes from Kent Overstreet. This
enables some nice future work on making arbitrarily sized bios
possible, and splitting more efficient. Related fixes to immutable
bio_vecs:
- dm-cache immutable fixup from Mike Snitzer.
- btrfs immutable fixup from Muthu Kumar.
- bio-integrity fix from Nic Bellinger, which is also going to stable"
* 'for-3.14/core' of git://git.kernel.dk/linux-block: (44 commits)
xtensa: fixup simdisk driver to work with immutable bio_vecs
block/blk-mq-cpu.c: use hotcpu_notifier()
blk-mq: for_each_* macro correctness
block: Fix memory leak in rw_copy_check_uvector() handling
bio-integrity: Fix bio_integrity_verify segment start bug
block: remove unrelated header files and export symbol
blk-mq: uses page->list incorrectly
blk-mq: use __smp_call_function_single directly
btrfs: fix missing increment of bi_remaining
Revert "block: Warn and free bio if bi_end_io is not set"
block: Warn and free bio if bi_end_io is not set
blk-mq: fix initializing request's start time
block: blk-mq: don't export blk_mq_free_queue()
block: blk-mq: make blk_sync_queue support mq
block: blk-mq: support draining mq queue
dm cache: increment bi_remaining when bi_end_io is restored
block: fixup for generic bio chaining
block: Really silence spurious compiler warnings
block: Silence spurious compiler warnings
block: Kill bio_pair_split()
...
Race conditions are theoretically possible between the MPT PCI device
removal and the generic PCI bus rescan and device removal that can be
triggered via sysfs.
To avoid those race conditions make the MPT PCI code use
pci_stop_and_remove_bus_device_locked().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When we start sharing biovecs, keeping bi_vcnt accurate for splits is
going to be error prone - and unnecessary, if we refactor some code.
So bio_segments() has to go - but most of the existing users just needed
to know if the bio had multiple segments, which is easier - add a
bio_multiple_segments() for them.
(Two of the current uses of bio_segments() are going to go away in a
couple patches, but the current implementation of bio_segments() is
unsafe as soon as we start doing driver conversions for immutable
biovecs - so implement a dumb version for bisectability, it'll go away
in a couple patches)
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Hannes Reinecke