- Fix Tegra OF node reference leak (Nishka Dasgupta)
- Add #defines for PCIe Data Link Feature and Physical Layer 16.0 GT/s
features (Vidya Sagar)
- Disable MSI for Tegra Root Ports since they don't support using MSI for
all Root Port events (Vidya Sagar)
- Group DesignWare write-protected register writes together (Vidya Sagar)
- Move DesignWare capability search interfaces so they can be used by
both host and endpoint drivers (Vidya Sagar)
- Add DesignWare extended capability search interfaces (Vidya Sagar)
- Export dw_pcie_wait_for_link() so drivers can be modules (Vidya Sagar)
- Add "snps,enable-cdm-check" DT binding for Configuration Dependent
Module (CDM) register checking (Vidya Sagar)
- Add DesignWare support for "snps,enable-cdm-check" CDM checking (Vidya
Sagar)
- Add "supports-clkreq" DT binding for host drivers to decide whether to
advertise low power features (Vidya Sagar)
- Add DT binding for Tegra194 (Vidya Sagar)
- Add DT binding for Tegra194 P2U (PIPE to UPHY) block (Vidya Sagar)
- Add support for Tegra194 P2U (PIPE to UPHY) (Vidya Sagar)
- Add support for Tegra194 host controller (Vidya Sagar)
- Add Tegra support for sideband PERST# and CLKREQ# for C5 (Vidya Sagar)
- Add Tegra support for slot regulators for p2972-0000 platform (Vidya
Sagar)
* lorenzo/pci/tegra:
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
phy: tegra: Add PCIe PIPE2UPHY support
dt-bindings: PHY: P2U: Add Tegra194 P2U block
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: Add PCIe supports-clkreq property
PCI: dwc: Add support to enable CDM register check
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Export dw_pcie_wait_for_link() API
PCI: dwc: Add extended configuration space capability search API
PCI: dwc: Move config space capability search API
PCI: dwc: Group DBI registers writes requiring unlocking
PCI: Disable MSI for Tegra root ports
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: tegra: Fix OF node reference leak
Some PCIe controllers can be set to either Host or EP according to some
early boot FW. To make sure there is no discrepancy (e.g. FW configured
the port to EP mode while the DT specifies it as a host bridge or vice
versa), a check has been added for each mode.
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Some of DesignWare core's DBI registers (a.k.a configuration space
registers) are write-protected with a lock without enabling which they
are read-only by default.
These write-protected registers are implementation specific. Tegra194's
BAR-0 register which is at offset 0x10 in the configuration space is an
example. Current implementation in dw_pcie_setup_rc() API attempts to
unlock those write-protected registers whenever they are updated and
lock them back again for writing.
Group all write-protected registers writes so that locking and unlocking
is performed once to avoid bloating the code with multiple unlock/lock
sequences for all those write-protected registers.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Export all configuration space access APIs and also other APIs to
support host controller drivers of dwc core based implementations while
adding support for .remove() hook to build their respective drivers as
modules.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Add an API to group all the tasks to be done to de-initialize host which
can then be called by any dwc core based driver implementations
while adding .remove() support in their respective drivers.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
- Move IRQ register address computation inside macros (Kishon Vijay
Abraham I)
- Separate legacy IRQ and MSI configuration (Kishon Vijay Abraham I)
- Use hwirq, not virq, to get MSI IRQ number offset (Kishon Vijay Abraham
I)
- Squash ks_pcie_handle_msi_irq() into ks_pcie_msi_irq_handler() (Kishon
Vijay Abraham I)
- Add dwc support for platforms with custom MSI controllers (Kishon Vijay
Abraham I)
- Add keystone-specific MSI controller (Kishon Vijay Abraham I)
- Remove dwc host_ops previously used for keystone-specific MSI (Kishon
Vijay Abraham I)
- Skip dwc default MSI init if platform has custom MSI controller (Kishon
Vijay Abraham I)
- Implement .start_link() and .stop_link() for keystone endpoint support
(Kishon Vijay Abraham I)
- Add keystone "reg-names" DT binding (Kishon Vijay Abraham I)
- Squash ks_pcie_dw_host_init() into ks_pcie_add_pcie_port() (Kishon
Vijay Abraham I)
- Get keystone register resources from DT by name, not index (Kishon
Vijay Abraham I)
- Get DT resources in .probe() to prepare for endpoint support (Kishon
Vijay Abraham I)
- Add "ti,syscon-pcie-mode" DT property for PCIe mode configuration
(Kishon Vijay Abraham I)
- Explicitly set keystone to host mode (Kishon Vijay Abraham I)
- Document DT "atu" reg-names requirement for DesignWare core >= 4.80
(Kishon Vijay Abraham I)
- Enable dwc iATU unroll for endpoint mode as well as host mode (Kishon
Vijay Abraham I)
- Add dwc "version" to identify core >= 4.80 for ATU programming (Kishon
Vijay Abraham I)
- Don't build ARM32-specific keystone code on ARM64 (Kishon Vijay Abraham
I)
- Add DT binding for keystone PCIe RC in AM654 SoC (Kishon Vijay Abraham
I)
- Add keystone support for AM654 SoC PCIe RC (Kishon Vijay Abraham I)
- Reset keystone PHYs before enabling them (Kishon Vijay Abraham I)
- Make of_pci_get_max_link_speed() available to endpoint drivers as well
as host drivers (Kishon Vijay Abraham I)
- Add keystone support for DT "max-link-speed" property (Kishon Vijay
Abraham I)
- Add endpoint library support for BAR buffer alignment (Kishon Vijay
Abraham I)
- Make all dw_pcie_ep_ops structs const (Kishon Vijay Abraham I)
- Fix fencepost error in dw_pcie_ep_find_capability() (Kishon Vijay
Abraham I)
- Add dwc hooks for dbi/dbi2 that share the same address space (Kishon
Vijay Abraham I)
- Add keystone support for TI AM654x in endpoint mode (Kishon Vijay
Abraham I)
- Configure designware endpoints to advertise smallest resizable BAR
(1MB) (Kishon Vijay Abraham I)
- Align designware endpoint ATU windows for raising MSIs (Kishon Vijay
Abraham I)
- Add endpoint test support for TI AM654x (Kishon Vijay Abraham I)
- Fix endpoint test test_reg_bar issue (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
misc: pci_endpoint_test: Fix test_reg_bar to be updated in pci_endpoint_test
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size
PCI: keystone: Add support for PCIe EP in AM654x Platforms
dt-bindings: PCI: Add PCI EP DT binding documentation for AM654
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: dwc: Fix dw_pcie_ep_find_capability() to return correct capability offset
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: endpoint: Add support to specify alignment for buffers allocated to BARs
PCI: keystone: Add support to set the max link speed from DT
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint drivers
PCI: keystone: Invoke phy_reset() API before enabling PHY
PCI: keystone: Add support for PCIe RC in AM654x Platforms
dt-bindings: PCI: Add PCI RC DT binding documentation for AM654
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: dwc: Enable iATU unroll for endpoint too
dt-bindings: PCI: Document "atu" reg-names
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Move resources initialization to prepare for EP support
PCI: keystone: Use platform_get_resource_byname() to get memory resources
PCI: keystone: Perform host initialization in a single function
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Cleanup error_irq configuration
PCI: keystone: Add start_link()/stop_link() dw_pcie_ops
PCI: dwc: Remove default MSI initialization for platform specific MSI chips
PCI: dwc: Remove Keystone specific dw_pcie_host_ops
PCI: keystone: Use Keystone specific msi_irq_chip
PCI: dwc: Add support to use non default msi_irq_chip
PCI: keystone: Cleanup ks_pcie_msi_irq_handler()
PCI: keystone: Use hwirq to get the MSI IRQ number offset
PCI: keystone: Add separate functions for configuring MSI and legacy interrupt
PCI: keystone: Cleanup interrupt related macros
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
Currently DWC host does not support the remove callback, but nothing
prevents us from supporting it.
Save the root bus for clean up work in driver remove code paths to allow
DWC host drivers to implement their remove hook as, eg:
static int foo_pcie_remove(struct platform_device *pdev)
{
...
pci_stop_root_bus(pp->root_bus);
pci_remove_root_bus(pp->root_bus);
dw_pcie_free_msi(pp);
...
}
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Use devm_pci_alloc_host_bridge() to simplify the error code path. This
also fixes a leak in the dw_pcie_host_init() error path.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
CC: stable@vger.kernel.org # v4.13+
If we ever did MSI-related initializations, we need to call
dw_pcie_free_msi() in the error code path.
Remove the IS_ENABLED(CONFIG_PCI_MSI) check for MSI init because
pci_msi_enabled() already has a stub for !CONFIG_PCI_MSI.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
To avoid a memory leak, free the page allocated for MSI IRQ in
dw_pcie_free_msi().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Check msi_irq variable before calling irq_set_chained_handler() and
irq_set_handler_data(), lest we call those functions for an invalid MSI
IRQ.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
iatu_unroll_enabled flag is set only for Designware in host mode.
However iATU unroll can be applicable for endpoint mode too. Set
iatu_unroll_enabled flag in dw_pcie_setup() which is common for
both host mode and endpoint mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Platforms which populate msi_host_init() have their own MSI controller
logic. Writing to MSI control registers on platforms which do not use
Designware's MSI controller logic might have side effects.
To be safe, do not write to MSI control registers if the platform uses
its own MSI controller logic instead of Designware's MSI one.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Now that Keystone started using its own msi_irq_chip, remove
Keystone specific callback functions defined in dw_pcie_host_ops.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use Keystone specific msi_irq_chip to configure the MSI controller
logic in the PCIe keystone wrapper instead of using the default
Designware msi_irq chip (dw_pci_msi_bottom_irq_chip) with
callback functions for configuring the Keystone MSI controller.
This will help to remove Keystone specific callback functions
added in dw_pcie_host_ops.
Move the default msi_irq_chip assignment to dw_pcie_host_init since
platforms that doesn't use the default msi_irq_chip will assign
msi_irq_chip in the msi_host_init() callback.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Platforms using DesignWare IP use dw_pci_msi_bottom_irq_chip for
configuring the MSI controller logic within the DesignWare IP. However
certain platforms like Keystone (K2G) which uses DesignWare IP have
their own MSI controller logic. For handling such platforms,
the irqchip ops use msi_irq_ack(), msi_set_irq(), msi_clear_irq()
callback functions.
Add support to use different msi_irq_chip with default set to
dw_pci_msi_bottom_irq_chip. This is in preparation to get rid of
msi_irq_ack(), msi_set_irq(), msi_clear_irq() and other Keystone
specific dw_pcie_host_ops.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Since 7c5925afbc (PCI: dwc: Move MSI IRQs allocation to IRQ domains
hierarchical API) the MSI init claims one of the controller IRQs as a
chained IRQ line for the MSI controller. On some designs, like the i.MX6,
this line is shared with a PCIe legacy IRQ. When the line is claimed for
the MSI domain, any device trying to use this legacy IRQs will fail to
request this IRQ line.
As MSI and legacy IRQs are already mutually exclusive on the DWC core,
as the core won't forward any legacy IRQs once any MSI has been enabled,
users wishing to use legacy IRQs already need to explictly disable MSI
support (usually via the pci=nomsi kernel commandline option). To avoid
any issues with MSI conflicting with legacy IRQs, just skip all of the
DWC MSI initalization, including the IRQ line claim, when MSI is disabled.
Fixes: 7c5925afbc ("PCI: dwc: Move MSI IRQs allocation to IRQ domains hierarchical API")
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: stable@vger.kernel.org
Default implementation of pcie_rd_other_conf() and
dw_pcie_wd_other_conf() share more than 80% of their code. Move shared
code into a dedicated subroutine and convert pcie_rd_other_conf() and
dw_pcie_wd_other_conf() to use it. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Replace bit rotation operation (1 << bit) with BIT(bit), which
simplifies code reading.
No functional change is intended.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Improve code readability and simplifies mask/unmask operations by
inverting the applied logic (no functional change is intended).
Replace variable name from irq_status to irq_mask, since its goal is to
keep track of which interrupts are masked or not.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Rename variable from data to d to maintain consistency between driver
functions.
No functional change is intended.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Rename variable from data to d to maintain consistency between driver
functions.
No functional change is intended.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Rename variable from data to d to maintain consistency between driver
functions, such as dw_pci_setup_msi_msg().
No functional change is intended.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Rename variable from data to d to maintain consistency between driver
functions, such as dw_msi_mask_irq() and dw_msi_unmask_irq().
No functional change is intended.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
- Mask DesignWare interrupts instead of disabling them to avoid lost
interrupts (Marc Zyngier)
- Add locking when acking DesignWare interrupts (Marc Zyngier)
- Ack DesignWare interrupts in the proper callbacks (Marc Zyngier)
* remotes/lorenzo/pci/dwc-msi:
PCI: dwc: Move interrupt acking into the proper callback
PCI: dwc: Take lock when ACKing an interrupt
PCI: dwc: Use interrupt masking instead of disabling
The DWC PCIe core contains various separate register spaces: DBI, DBI2,
ATU, DMA, etc. The relationship between the addresses of these register
spaces is entirely determined by the implementation of the IP block, not
by the IP block design itself. Hence, the DWC driver must not make
assumptions that one register space can be accessed at a fixed offset from
any other register space. To avoid such assumptions, introduce an
explicit/separate register pointer for the ATU register space. In
particular, the current assumption is not valid for NVIDIA's T194 SoC.
The ATU register space is only used on systems that require unrolled ATU
access. This property is detected at run-time for host controllers, and
when this is detected, this patch provides a default value for atu_base
that matches the previous assumption re: register layout. An alternative
would be to update all drivers for HW that requires unrolled access to
explicitly set atu_base. However, it's hard to tell which drivers would
require atu_base to be set. The unrolled property is not detected for
endpoint systems, and so any endpoint driver that requires unrolled access
must explicitly set the iatu_unroll_enabled flag (none do at present), and
so a check is added to require the driver to also set atu_base while at
it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
The write to the status register is really an ACK for the HW,
and should be treated as such by the driver. Let's move it to the
irq_ack() callback, which will prevent people from moving it around
in order to paper over other bugs.
Fixes: 8c934095fa ("PCI: dwc: Clear MSI interrupt status after it is handled,
not before")
Fixes: 7c5925afbc ("PCI: dwc: Move MSI IRQs allocation to IRQ domains
hierarchical API")
Link: https://lore.kernel.org/linux-pci/20181113225734.8026-1-marc.zyngier@arm.com/
Reported-by: Trent Piepho <tpiepho@impinj.com>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Tested-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Bizarrely, there is no lock taken in the irq_ack() helper. This
puts the ACK callback provided by a specific platform in a awkward
situation where there is no synchronization that would be expected
on other callback.
Introduce the required lock, giving some level of uniformity among
callbacks.
Fixes: 7c5925afbc ("PCI: dwc: Move MSI IRQs allocation to IRQ domains
hierarchical API")
Link: https://lore.kernel.org/linux-pci/20181113225734.8026-1-marc.zyngier@arm.com/
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Tested-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
The dwc driver is showing an interesting level of brokeness, as it
insists on using the enable/disable set of registers to mask/unmask
MSIs, meaning that an MSIs being generated while the interrupt is in
that "disabled" state will simply be lost.
Let's move to the mask/unmask set of registers, which offers the
expected semantics.
Fixes: 7c5925afbc ("PCI: dwc: Move MSI IRQs allocation to IRQ domains
hierarchical API")
Link: https://lore.kernel.org/linux-pci/20181113225734.8026-1-marc.zyngier@arm.com/
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Tested-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Native PCI drivers for root complex devices were originally all in
drivers/pci/host/. Some of these devices can also be operated in endpoint
mode. Drivers for endpoint mode didn't seem to fit in the "host"
directory, so we put both the root complex and endpoint drivers in
per-device directories, e.g., drivers/pci/dwc/, drivers/pci/cadence/, etc.
These per-device directories contain trivial Kconfig and Makefiles and
clutter drivers/pci/. Make a new drivers/pci/controllers/ directory and
collect all the device-specific drivers there.
No functional change intended.
Link: https://lkml.kernel.org/r/1520304202-232891-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Bjorn Helgaas