After commit 171a9bae68 ("staging/octeon: Allow test build on
!MIPS"), the following combination of configs cause a few Kconfig
warnings and build errors (distilled from arm allyesconfig and Randy's
randconfig builds):
CONFIG_NETDEVICES=y
CONFIG_STAGING=y
CONFIG_COMPILE_TEST=y
and CONFIG_OCTEON_ETHERNET as either a module or built-in.
WARNING: unmet direct dependencies detected for MDIO_OCTEON
Depends on [n]: NETDEVICES [=y] && MDIO_DEVICE [=y] && MDIO_BUS [=y]
&& 64BIT [=n] && HAS_IOMEM [=y] && OF_MDIO [=n]
Selected by [y]:
- OCTEON_ETHERNET [=y] && STAGING [=y] && (CAVIUM_OCTEON_SOC ||
COMPILE_TEST [=y]) && NETDEVICES [=y]
In file included from ../drivers/net/phy/mdio-octeon.c:14:
../drivers/net/phy/mdio-cavium.h:111:36: error: implicit declaration of
function ‘writeq’; did you mean ‘writel’?
[-Werror=implicit-function-declaration]
111 | #define oct_mdio_writeq(val, addr) writeq(val, (void *)addr)
| ^~~~~~
CONFIG_64BIT is not strictly necessary if the proper readq/writeq
definitions are included from io-64-nonatomic-lo-hi.h.
CONFIG_OF_MDIO is not needed when CONFIG_COMPILE_TEST is enabled because
of commit f9dc9ac516 ("of/mdio: Add dummy functions in of_mdio.h.").
Fixes: 171a9bae68 ("staging/octeon: Allow test build on !MIPS")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".
[0] https://marc.info/?t=156413509900003&r=1&w=2
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: liuyonglong <liuyonglong@huawei.com>
Tested-by: liuyonglong <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AST2600 design separates the MDIO controllers from the MAC, which is
where they were placed in the AST2400 and AST2500. Further, the register
interface is reworked again, so now we have three possible different
interface implementations, however this driver only supports the
interface provided by the AST2600. The AST2400 and AST2500 will continue
to be supported by the MDIO support embedded in the FTGMAC100 driver.
The hardware supports both C22 and C45 mode, but for the moment only C22
support is implemented.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_led_trigger_change_speed(), there is an if statement on line 48
to check whether phy->last_triggered is NULL:
if (!phy->last_triggered)
When phy->last_triggered is NULL, it is used on line 52:
led_trigger_event(&phy->last_triggered->trigger, LED_OFF);
Thus, a possible null-pointer dereference may occur.
To fix this bug, led_trigger_event(&phy->last_triggered->trigger,
LED_OFF) is called when phy->last_triggered is not NULL.
This bug is found by a static analysis tool STCheck written by
the OSLAB group in Tsinghua University.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is perfectly ok to not have an gpio attached to the fixed-link node. So
the driver should not throw an error message when the gpio is missing.
Fixes: 5468e82f70 ("net: phy: fixed-phy: Drop GPIO from fixed_phy_add()")
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory allocated for the stats array may contain arbitrary data.
Fixes: e4f9ba642f ("net: phy: mscc: add support for VSC8514 PHY.")
Fixes: 00d70d8e0e ("net: phy: mscc: add support for VSC8574 PHY")
Fixes: a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY")
Fixes: f76178dc52 ("net: phy: mscc: add ethtool statistics counters")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP modules connected using the SGMII interface have their own PHYs which
are handled by the struct phylink's phydev field. On the other hand, for
the modules connected using 1000Base-X interface that field is not set.
Since commit ce0aa27ff3 ("sfp: add sfp-bus to bridge between network
devices and sfp cages") phylink_start() ends up setting the phydev field
using the sfp-bus infrastructure, which eventually calls phy_start() on it,
and then calling phy_start() again on the same phydev from phylink_start()
itself. Similar call sequence holds for phylink_stop(), only in the reverse
order. This results in WARNs during network interface bringup and shutdown
when a copper SFP module is connected, as phy_start() and phy_stop() are
called twice in a row for the same phy_device:
% ip link set up dev eth0
------------[ cut here ]------------
called from state UP
WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0
Modules linked in:
CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1
NIP: c0227bf0 LR: c0227bf0 CTR: c004d224
REGS: df547720 TRAP: 0700 Not tainted (5.2.0+)
MSR: 00029000 <CE,EE,ME> CR: 24002822 XER: 00000000
GPR00: c0227bf0 df5477d8 df5d7080 00000014 df9d2370 df9d5ac4 1f4eb000 00000001
GPR08: c061fe58 00000000 00000000 df5477d8 0000003c 100c8768 00000000 00000000
GPR16: df486a00 c046f1c8 c046eea0 00000000 c046e904 c0239604 db68449c 00000000
GPR24: e9083204 00000000 00000001 db684460 e9083404 00000000 db6dce00 db6dcc00
NIP [c0227bf0] phy_start+0x74/0xc0
LR [c0227bf0] phy_start+0x74/0xc0
Call Trace:
[df5477d8] [c0227bf0] phy_start+0x74/0xc0 (unreliable)
[df5477e8] [c023cad0] startup_gfar+0x398/0x3f4
[df547828] [c023cf08] gfar_enet_open+0x364/0x374
[df547898] [c029d870] __dev_open+0xe4/0x140
[df5478c8] [c029db70] __dev_change_flags+0xf0/0x188
[df5478f8] [c029dc28] dev_change_flags+0x20/0x54
[df547918] [c02ae304] do_setlink+0x310/0x818
[df547a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
[df547c28] [c02b222c] rtnl_newlink+0x48/0x68
[df547c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
[df547c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
[df547cd8] [c02cba3c] netlink_unicast+0x114/0x19c
[df547d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
[df547d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
[df547d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
[df547e98] [c027df7c] __sys_sendmsg+0x68/0x84
[df547ef8] [c027e430] sys_socketcall+0x1a0/0x204
[df547f38] [c000d1d8] ret_from_syscall+0x0/0x38
--- interrupt: c01 at 0xfd4e030
LR = 0xfd4e010
Instruction dump:
813f0188 38800000 2b890005 419d0014 3d40c046 5529103a 394aa208 7c8a482e
3c60c046 3863a1b8 4cc63182 4be009a1 <0fe00000> 48000030 3c60c046 3863a1d0
---[ end trace d4c095aeaf6ea998 ]---
and
% ip link set down dev eth0
------------[ cut here ]------------
called from state HALTED
WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88
<...>
Call Trace:
[df581788] [c0228450] phy_stop+0x3c/0x88 (unreliable)
[df581798] [c022d548] sfp_sm_phy_detach+0x1c/0x44
[df5817a8] [c022e8cc] sfp_sm_event+0x4b0/0x87c
[df581848] [c022f04c] sfp_upstream_stop+0x34/0x44
[df581858] [c0225608] phylink_stop+0x7c/0xe4
[df581868] [c023c57c] stop_gfar+0x7c/0x94
[df581888] [c023c5b8] gfar_close+0x24/0x94
[df5818a8] [c0298688] __dev_close_many+0xdc/0xf8
[df5818c8] [c029db58] __dev_change_flags+0xd8/0x188
[df5818f8] [c029dc28] dev_change_flags+0x20/0x54
[df581918] [c02ae304] do_setlink+0x310/0x818
[df581a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
[df581c28] [c02b222c] rtnl_newlink+0x48/0x68
[df581c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
[df581c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
[df581cd8] [c02cba3c] netlink_unicast+0x114/0x19c
[df581d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
[df581d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
[df581d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
[df581e98] [c027df7c] __sys_sendmsg+0x68/0x84
[df581ef8] [c027e430] sys_socketcall+0x1a0/0x204
[df581f38] [c000d1d8] ret_from_syscall+0x0/0x38
<...>
---[ end trace d4c095aeaf6ea999 ]---
SFP modules with the 1000Base-X interface are not affected.
Place explicit calls to phy_start() and phy_stop() before enabling or after
disabling an attached SFP module, where phydev is not yet set (or is
already unset), so they will be made only from the inside of sfp-bus, if
needed.
Fixes: 2179626156 ("net: phy: warn if phy_start is called from invalid state")
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX power read from the SFP uses units of 0.1uW. This must be
scaled to units of uW for HWMON. This requires a divide by 10, not the
current 100.
With this change in place, sensors(1) and ethtool -m agree:
sff2-isa-0000
Adapter: ISA adapter
in0: +3.23 V
temp1: +33.1 C
power1: 270.00 uW
power2: 200.00 uW
curr1: +0.01 A
Laser output power : 0.2743 mW / -5.62 dBm
Receiver signal average optical power : 0.2014 mW / -6.96 dBm
Reported-by: chris.healy@zii.aero
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables phy_basic_ports_array, phy_fibre_port_array and
phy_all_ports_features_array are declared static and marked
EXPORT_SYMBOL_GPL(), which is at best an odd combination.
Because the variables were decided to be a part of API, this commit
removes the static attributes and adds the declarations to the header.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linkmode_mod_bit is introduced as a helper function to set/clear
bits in a linkmode.
Replace the if else code structure with a call to the helper
linkmode_mod_bit.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ef7bfa8472.
Russell King espressed some strong opposition to this
change, explaining that this is trying to make phylink
behave outside of how it has been designed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_state field of phylink should carry only valid information
especially when this can be passed to the .mac_config callback.
Update the an_enabled field with the autoneg state in the
phylink_phy_change function.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The acpi_node_get_property_reference() doesn't return ACPI error codes,
it just returns regular negative kernel error codes. This patch doesn't
affect run time, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ruslan Babayev <ruslan@babayev.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "net: phy: Add detection of 1000BaseX link mode support" added
support for not filtering out 1000BaseX mode from the PHY's supported
modes in genphy_config_init, but we have to make a similar change in
genphy_read_abilities in order to actually detect it as a supported mode
in the first place. Add this in.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This puts the quad PHY ports in power-down mode when the PHY transitions
to the PHY_HALTED state. It is likely that all the other PHYs support
the BMCR_PDOWN bit, but I only have the BCM5464R to test.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfp_check_state can potentially be called by both a threaded IRQ handler
and delayed work. If it is concurrently called, it could result in
incorrect state management. Add a st_mutex to protect the state - this
lock gets taken outside of code that checks and handle state changes, and
the existing sm_mutex nests inside of it.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP device polling can cause problems during the shutdown process if the
parent devices of the network controller have been shut down already.
This problem was seen on the iMX6 platform with PCIe devices, where
accessing the device after the bus is shut down causes a hang.
Free any acquired GPIO interrupts and stop all delayed work in the SFP
driver during the shutdown process, so that we ensure that no pending
operations are still occurring after the SFP shutdown completes.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Resent to net instead of net-next - may clash with Anders Roxell's patch
series addressing duplicate module names]
Commit 31dd83b966 ("net-next: phy: new Asix Electronics PHY driver")
introduced a new PHY driver drivers/net/phy/asix.c that causes a module
name conflict with a pre-existiting driver (drivers/net/usb/asix.c).
The PHY driver is used by the X-Surf 100 ethernet card driver, and loaded
by that driver via its PHY ID. A rename of the driver looks unproblematic.
Rename PHY driver to ax88796b.c in order to resolve name conflict.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Fixes: 31dd83b966 ("net-next: phy: new Asix Electronics PHY driver")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 1000BaseX to the link modes which are detected based on the
MII_ESTATUS register as per 802.3 Clause 22. This allows PHYs which
support 1000BaseX to work properly with drivers using phylink.
Previously 1000BaseX support was not detected, and if that was the only
mode the PHY indicated support for, phylink would refuse to attach it
due to the list of supported modes being empty.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the early days of phylib we had a functionality that changed to the
next lower speed in fixed mode if no link was established after a
certain period of time. This functionality has been removed years ago,
and state PHY_FORCING isn't needed any longer. Instead we can go from
UP to RUNNING or NOLINK directly (same as in autoneg mode).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid reducing the support mask as a result of the interface type
selected for SFP modules, or when setting the link settings through
ethtool - this should only change when the supported link modes of
the hardware combination change.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFP modules do not like reads longer than 16 bytes, so read the
EEPROM in chunks of 16 bytes at a time. This behaviour is not specified
in the SFP MSAs, which specifies:
"The serial interface uses the 2-wire serial CMOS E2PROM protocol
defined for the ATMEL AT24C01A/02/04 family of components."
and
"As long as the SFP+ receives an acknowledge, it shall serially clock
out sequential data words. The sequence is terminated when the host
responds with a NACK and a STOP instead of an acknowledge."
We must avoid breaking a read across a 16-bit quantity in the diagnostic
page, thankfully all 16-bit quantities in that page are naturally
aligned.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sfp-bus code now no longer has any use for the network device
structure, so remove its use.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add attach and detach methods for SFP buses, which will allow us to get
rid of the netdev storage in sfp-bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow userspace to generate Clause 45 MII access cycles via phylib.
This is useful for tools such as mii-diag to be able to inspect Clause
45 PHYs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for using GPIO interrupts with a fixed-link GPIO rather than
polling the GPIO every second and invoking the phylink resolution. This
avoids unnecessary calls to mac_config().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev used in the phylink ioctl emulation is never used, so let's
remove it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
We face the issue that link change interrupt and link status may be
reported by different PHY layers. As a result the link change
interrupt may occur before the link status changes.
Export phy_queue_state_machine to allow PHY drivers to specify a
delay between link status change interrupt and link status check.
v2:
- change jiffies parameter type to unsigned long
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylib interrupt handler handles link change events only currently.
However PHY drivers may want to use other interrupt sources too,
e.g. to report temperature monitoring events. Therefore add a callback
to struct phy_driver allowing PHY drivers to implement a custom
interrupt handler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a step towards allowing PHY drivers to handle more
interrupt sources than just link change. E.g. several PHY's have
built-in temperature monitoring and can raise an interrupt if a
temperature threshold is exceeded. We may be interested in such
interrupts also if the phylib state machine isn't started.
Therefore move enabling interrupts to phy_request_interrupt().
v2:
- patch added to series
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the latest addition to the PHYLINK infrastructure, we are faced
with a decision on when to print necessary info using the struct
net_device and when with the struct device.
Add a series of macros that encapsulate this decision and replace all
uses of netdev_err&co with phylink_err.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the PHYLINK_DEV operation type, the PHYLINK infrastructure can work
without an attached net_device. For printing usecases, instead, a struct
device * should be passed to PHYLINK using the phylink_config structure.
Also, netif_carrier_* calls ar guarded by the presence of a valid
net_device. When using the PHYLINK_DEV operation type, we cannot check
link status using the netif_carrier_ok() API so instead, keep an
internal state of the MAC and call mac_link_{down,up} only when the link
changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.
A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.
At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.
This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that reduces the clutter in phylink_resolve
around calling the .mac_link_up/.mac_link_down driver callbacks. In a
further patch this logic will be extended to emit notifications in case
a net device does not exist.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export a phy_standalone device attribute that is meant to give the
indication that this PHY lacks an attached_dev and its corresponding
sysfs link. The attribute will be created only when the
phy_attach_direct() function will be called with a NULL net_device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A prerequisite for PHYLIB to work in the absence of a struct net_device
is to not access pointers to it.
Changes are needed in the following areas:
- Printing: In some places netdev_err was replaced with phydev_err.
- Incrementing reference count to the parent MDIO bus driver: If there
is no net device, then the reference count should definitely be
incremented since there is no chance that it was an Ethernet driver
who registered the MDIO bus.
- Sysfs links are not created in case there is no attached_dev.
- No netif_carrier_off is done if there is no attached_dev.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that wraps the operation of creating sysfs
links between the netdev->phydev and the phydev->attached_dev.
This is needed to keep the indentation level in check in a follow-up
patch where this function will be guarded against the existence of a
phydev->attached_dev.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY_INTERFACE_MODE_RGMII_RXID is less then TXID
so code to set tx delay is never called.
Fixes: 2a10154abc ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy state machine calls _config_init just after
reset.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After reset SGMII Autoneg timer is set to 2us (bits 6 and 5 are 01).
That is not enough to finalize autonegatiation on some devices.
Increase this timer duration to maximum supported 16ms.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For supporting 10Mps speed in SGMII mode DP83867_10M_SGMII_RATE_ADAPT bit
of DP83867_10M_SGMII_CFG register has to be cleared by software.
That does not affect speeds 100 and 1000 so can be done on init.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected. Warn the user when the
PHY fails to boot the firmware and refuse to initialise.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call. This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers don't have to and shouldn't fiddle with phylib internals.
Most of the code in bcm87xx_config_init() can be removed because
phylib takes care.
In addition I replaced usage of PHY_10GBIT_FEC_FEATURES with an
implementation of the get_features callback. PHY_10GBIT_FEC_FEATURES
is used by this driver only and it's questionable whether there
will be any other PHY supporting this mode only. Having said that
in one of the next kernel versions we may decide to remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we didn't support mode USXGMII, and in order to not break few
boards mode XGMII was accepted for the AQR107 family even though it
doesn't support XGMII. Add USXGMII support to the Aquantia PHY driver
and warn if XGMII mode is set.
v2:
- add warning if XGMII mode is set
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All LXT PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic
genphy_{suspend,resume} functions added by
commit 0f0ca340e5 ("phy: power management support").
LXT970 is left aside because all registers get cleared upon
"power down" exit.
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a link mode for 100BaseT1, use it in
phy_basic_t1_features so T1 PHY drivers will indicate this mode via
the Ethtool API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add link modes for 100Mbps and 1Gbps over a single pair.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was being done in config the first time the phy was configured.
Should be in the probe method.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insure property is in valid range and fail when reading DT if it is not.
Also add error message for existing failure if required property is not
present.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver would only set the IO impedance value when RGMII internal
delays were enabled. There is no reason for this. Move the IO
impedance block out of the RGMII delay block.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables used to store u32 DT properties were signed ints. This
doesn't work properly if the value of the property were to overflow.
Use unsigned variables so this doesn't happen.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code was assuming the reset default of the delay control register
was to have delay disabled. This is what the datasheet shows as the
register's initial value. However, that's not actually true: the
default is controlled by the PHY's pin strapping.
If the interface mode is selected as RX or TX delay only, insure the
other direction's delay is disabled.
If the interface mode is just "rgmii", with neither TX or RX internal
delay, one might expect that the driver should disable both delays. But
this is not what the driver does. It leaves the setting at the PHY's
strapping's default. And that default, for no pins with strapping
resistors, is to have delay enabled and 2.00 ns.
Rather than change this behavior, I've kept it the same and documented
it. No delay will most likely not work and will break ethernet on any
board using "rgmii" mode. If the board is strapped to have a delay and
is configured to use "rgmii" mode a warning is generated that "rgmii-id"
should have been used.
Also validate the delay values and fail if they are not in range.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally, the output clock pin is only used for testing and only serves
as a source of RF noise after this. It could be used to daisy-chain
PHYs, but this is uncommon. Since the PHY can disable the output, make
doing so an option. I do this by adding another enumeration to the
allowed values of ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep
clock output setting as is", which, depending on PHY strapping, might
not be outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the
previous behavior in this case).
Out of range values were silently converted into
DP83867_CLK_O_SEL_REF_CLK. Change this so they generate an error.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
Do not update the link interface mode while the link is down to avoid
spurious link interface changes.
Always call mac_config if we have a PHY to propagate the pause mode
settings to the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XGMII interface mode no longer works on AQR107 after the recent changes,
adding back support.
Fixes: 570c8a7d53 ("net: phy: aquantia: check for supported interface modes in config_init")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy id chosen by Amlogic is incorrectly set in the mdio mux and
does not match the phy driver.
It was not detected before because DT forces the use the correct driver
for the internal PHY.
Fixes: 7090425104 ("net: phy: add amlogic g12a mdio mux support")
Reported-by: Qi Duan <qi.duan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After calling phy_select_page() and until calling phy_restore_page(),
the mutex 'mdio_lock' is already locked, so the driver should use
non-locked version of phy functions. Or there will be a deadlock with
'mdio_lock'.
This replaces phy functions called from rtl8211e_config_init() to avoid
the deadlock issue.
Fixes: f81dadbcf7 ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding missing callbacks I missed that one had them set already.
Interesting that the compiler didn't complain.
Fixes: daf3ddbe11 ("net: phy: realtek: add missing page operations")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing page operation callbacks to few Realtek drivers.
This also fixes a NPE after the referenced commit added code to the
RTL8211E driver that uses phy_select_page().
Fixes: f81dadbcf7 ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's prone to problems if delay is cleared out for other than RGMII
modes. So lets set/clear the TX-delay in the config register only
if actually RGMII-like interface mode is requested. This only
concerns rtl8211f chips.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. Alas this is the only
documented info regarding the RGMII timing control configurations the PHY
provides. It turns out the same settings can be setup via MDIO registers
hidden in the extension pages layout. Particularly the extension page 0xa4
provides a register 0x1c, which bits 1 and 2 control the described delays.
They are used to implement the "rgmii-{id,rxid,txid}" phy-mode.
The hidden RGMII configs register utilization was found in the rtl8211e
U-boot driver:
https://elixir.bootlin.com/u-boot/v2019.01/source/drivers/net/phy/realtek.c#L99
There is also a freebsd-folks discussion regarding this register:
https://reviews.freebsd.org/D13591
It confirms that the register bits field must control the so called
configuration pins described in the table 12-13 of the official PHY
datasheet:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we report symmetric pause only, and we don't consider the local
pause capabilities. Let's properly consider local and remote
capabilities, and report also asymmetric pause.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have valid scenarios where ETHTOOL_LINK_MODE_Pause_BIT doesn't
need to be supported. Therefore extend the first check to check
for rx_pause being set.
See also phy_set_asym_pause:
rx=0 and tx=1: advertise asym pause only
rx=0 and tx=0: stop advertising both pause modes
The fixed commit isn't wrong, it's just the one that introduced the
linkmode bitmaps.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got an interesting report [0] that after resuming from hibernation
the link has 100Mbps instead of 1Gbps. Reason is that another OS has
been used whilst Linux was hibernated. And this OS speeds down the link
due to WoL. Therefore, when resuming, we shouldn't expect that what
the PHY advertises is what it did when hibernating.
Easiest way to do this is removing state PHY_RESUMING. Instead always
go via PHY_UP that configures PHY advertisement.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202851
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.
In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet). This patch makes sure this factory test
bit is cleared in config_init().
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Considering that in polling mode each link drop will be latched,
settings can't have changed if link was up and is up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
marvell_get_sset_count() returns how many statistics counters there
are. If the PHY supports fibre, there are 3, otherwise two.
marvell_get_strings() does not make this distinction, and always
returns 3 strings. This then often results in writing past the end
of the buffer for the strings.
Fixes: 2170fef78a ("Marvell phy: add field to get errors from fiber link.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.
So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.
BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for VSC8514 in Microsemi driver (mscc.c)
with more features.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC, downshifting, HP Auto-MDIX detection
and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default m88e151x LED configuration is 0x1177, used LED[0]
for 1000M link, LED[1] for 100M link, and LED[2] for active.
But for some boards, which use LED[0] for link, and LED[1] for
active, prefer to be 0x1040. To be compatible with this case,
this patch defines a new dev_flag, and set it before connect
phy in HNS3 driver. When phy initializing, using the new
LED configuration if this dev_flag is set.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames the GPIO reset of mdio devices from 'reset' to
'reset_gpio' to better differentiate between GPIO and
reset-controller driven reset line.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds support for PHY reset pins handled by a reset controller.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_sanitize_settings() is called from phy_start_aneg() only, and only
if phydev->autoneg isn't set. Therefore the removed code does nothing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device_create() we set phydev->autoneg = 1. This isn't changed
even if the PHY doesn't support autoneg. This seems to affect very
few PHY's, and they disable phydev->autoneg in their config_init
callback. So it's more of an improvement, therefore net-next.
The patch also wouldn't apply to older kernel versions because the
link mode bitmaps have been introduced recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If new PHY modes are added people may miss to update all relevant places
in the kernel. Therefore add a build bug check for new modes in enum
ethtool_link_mode_bit_indices that haven't been added to phylib yet.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently new modes have been added to ethtool.h, but the related
extension to phylib hasn't been done yet. So add support for these
modes.
v2:
- add missing 100Gbps and 50Gbps modes
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller