Commit 58bac7b8de failed to move the two
PLL files s3c2440-pll-12000000.c and s3c2440-pll-16934400.c, so place
these in arch/arm/mach-s3c2440 to fix this commit up.
As a note, these are not built by the default configuration and thus the
failure to move wasn't spotted until much later.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Follow the scheme used for IRQs. By default 16 GPIOs are allocated
for board use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Updates arch/arm Kconfig and Makefile for building the S5PV210 support.
Also modifies the plat-s5p Kconfig file to include the support for plat-s5p
for S5PV210.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds IRQ support for S5PV210. This patch adds interrupt
register definitions, IRQ definitions for various interrupt sources
and new VIC base for VIC2 and VIC3 in plat-s5p common irq code.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds clock support for S5PV210. This patch adds the clock
register definitions and the various system clocks in S5PV210.
Clocks that are common to other S5P SoC'c are added in the common
S5P clock support.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Samsung S5PV210 CPU. This patch also adds
an entry for S5PV210 cpu in plat-s5p cpu table.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[Updated the device ID to -1 since there's only one IISv4 device but the
S3C clock API tries to match based on the ID of the requesting device
(and not the name) -- broonie.]
Signed-Off-by: Jassi Brar <jassi.brar@samsung.com>
[ben-linux@fluff.org: Fixed Jassi's lastname]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch defines the platform device and the resources: IRQ, DMA and MEM,
needed by the AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The IISv4 controller is connected to the WM8580 on the board.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The PMIC LED on the SMDK6410 CPU board is driven by GPIO4 of the
WM8312 PMIC. Provide software control of this LED.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The Wolfson Microelectronics 1192-EV1 is a plug in module for the
SMDK6410 providing power using a WM8312 PMIC. This patch provides
initial hookup sufficient to initialise the board, though not all
features are fully described yet.
As part of this supplies for the system that are provided as a
single supply by one of the currently merged PMIC boards are
factored out so they can be reused between different regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
GPIO_E-[5,9] pin functionality was defined incorrectly.
The patch corrects and adds missing pins.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add AC97 controller to platform devices and initialize the AC97 gpios.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The recent changes in the UART code mean that we need to ensure that
the 4 UART case is only selected if S5PV210 is being compiled.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Updates arch/arm Kconfig and Makefile for building the S5P6442 support.
Also modifies the plat-s5p Kconfig file to include the support for plat-s5p
for S5P6442.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds IRQ support for S5P6442. This patch adds interrupt
register definitions, IRQ definitions for various interrupt sources
and new VIC base for VIC2 in plat-s5p common irq code.
Signed-off-by: Adityapratap Sharma <aditya.ps@samsung.com>
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds clock support for S5P6442. This patch adds the clock
register definitions and the various system clocks in S5P6442.
Signed-off-by: Adityapratap Sharma <aditya.ps@samsung.com>
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Samsung S5P6442 CPU. This patch also adds
an entry for S5P6442 cpu in plat-s5p cpu table.
Signed-off-by: Adityapratap Sharma <aditya.ps@samsung.com>
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
IRQ should be disabled on suspend and re-enabled on resume.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Without resources description driver fails during initialization.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the include/mach files out of plat-s3c and into the relevant
machine files. This does mean copying the files, but there is nowhere
else to put them.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Continue the clearout of plat-s3c by moving audio-simtec.h to plat-s3c24xx
as there are no current implementations outside of this platform.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the Kconfig entries from plat-s3c to plat-samsung and plat-s3c24xx
as necessary. The S3C_BOOT entries and the DMA configuration can go to
plat-samsung. The low-level UART configurations are currently S3C2XX
specific and can go to plat-s3c24xx.
Eliminating plat-s3c from the build process will be submitted seperately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the init.c and time.c files to plat-samsung from plat-s3c, thus
clearing the last files that are being built in here.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the map-base file to plat-samsung. To make the move easier, we do not
change the S3C_ prefix on many of the items as this would involve going
through altering all the dependencies.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move common headers from plat-s3c's include/plat directory into plat-samsung.
No need to fix any files, these are still included via <plat/>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Now we've move the support out of plat-s3c64xx for everything, eliminate
the platform directory arch/arm/plat-s3c64xx and remove it from the ARM
build configuration.
Note, PLAT_S3C64XX is kept around for the moment until the drivers that
depend on it can be updated, so it is moved to the mach-s3c64xx Kconfig.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
dma-plat.h is the last file left in plat-s3c64xx, but to remove it we
must also change the use of dma-plat.h by the core code and the s3c24xx
implementation.
Rename the s3c24xx dma-plat.h in the common plat-samsung directory as it
may be used for other ports. Move the specific dma bits into the
mach-s3c64xx directory and update the build as needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the Kconfig and PLAT_S3C64XX defines for the previous S3C64XX
directory structure now that the code is moved into mach-s3c64xx.
Note, we cannot currently remove plat-s3c64xx directory as we have a
pair of include files used within plat-s3c and plat-samsung that need
to find a new home.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Turn the init sequence of
s3c24xx_register_baseclocks(xtal);
s3c64xx_register_clocks();
s3c6400_register_clocks(S3C6410_CLKDIV0_ARM_MASK);
into a single call as this is now contained within one file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Merge plat-s3c64xx/s3c6400-clock.c mach-s3c64xx/clock.c placing all the
clock code into one place.
Note, no effort is made in this patch to squash the init functions
together.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since this file is small, and is compiled for both systems in this
architecture merge it into the cpu support file and remove the original
instead of moving it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the core S3C64XX support to mach-s3c64xx as it is unlikely to be used
outside of this directory. Also move the SoC header files in with it.
This includes the clock, cpu, cpufreq, dma, gpiolib and pll support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the S3C64XX specific device and setup files into mach-s3c64xx as
they are unlikely to be used outside of this code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the register and GPIO definition files from plat-s3c64xx into the
machine include direcotry as they are unlikely to be reused outside
mach-s3c64xx.
This move includes removing the empty <mach/regs-clock.h> and replacing
it with the <plat/regs-clock.h> implementation.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ben Dooks