The ARM architecture defines the memory locations that are permitted
to be accessed as the result of a speculative instruction fetch from
an exception level for which all stages of translation are disabled.
Specifically, the core is permitted to speculatively fetch from the
4KB region containing the current program counter 4K and next 4K.
When translation is changed from enabled to disabled for the running
exception level (SCTLR_ELn[M] changed from a value of 1 to 0), the
Falkor core may errantly speculatively access memory locations outside
of the 4KB region permitted by the architecture. The errant memory
access may lead to one of the following unexpected behaviors.
1) A System Error Interrupt (SEI) being raised by the Falkor core due
to the errant memory access attempting to access a region of memory
that is protected by a slave-side memory protection unit.
2) Unpredictable device behavior due to a speculative read from device
memory. This behavior may only occur if the instruction cache is
disabled prior to or coincident with translation being changed from
enabled to disabled.
The conditions leading to this erratum will not occur when either of the
following occur:
1) A higher exception level disables translation of a lower exception level
(e.g. EL2 changing SCTLR_EL1[M] from a value of 1 to 0).
2) An exception level disabling its stage-1 translation if its stage-2
translation is enabled (e.g. EL1 changing SCTLR_EL1[M] from a value of 1
to 0 when HCR_EL2[VM] has a value of 1).
To avoid the errant behavior, software must execute an ISB immediately
prior to executing the MSR that will change SCTLR_ELn[M] from 1 to 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ITSes on the Hip07 (as present in the Huawei D05) are broken when
it comes to addressing the redistributors, and need to be explicitely
told to address the VLPI page instead of the redistributor base address.
So let's add yet another quirk, fixing up the target address
in the command stream.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This update comes with:
* Support for lockless operation in the ARM io-pgtable code.
This is an important step to solve the scalability problems in
the common dma-iommu code for ARM
* Some Errata workarounds for ARM SMMU implemenations
* Rewrite of the deferred IO/TLB flush code in the AMD IOMMU
driver. The code suffered from very high flush rates, with the
new implementation the flush rate is down to ~1% of what it
was before
* Support for amd_iommu=off when booting with kexec. Problem
here was that the IOMMU driver bailed out early without
disabling the iommu hardware, if it was enabled in the old
kernel
* The Rockchip IOMMU driver is now available on ARM64
* Align the return value of the iommu_ops->device_group
call-backs to not miss error values
* Preempt-disable optimizations in the Intel VT-d and common
IOVA code to help Linux-RT
* Various other small cleanups and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=pmBf
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This update comes with:
- Support for lockless operation in the ARM io-pgtable code.
This is an important step to solve the scalability problems in the
common dma-iommu code for ARM
- Some Errata workarounds for ARM SMMU implemenations
- Rewrite of the deferred IO/TLB flush code in the AMD IOMMU driver.
The code suffered from very high flush rates, with the new
implementation the flush rate is down to ~1% of what it was before
- Support for amd_iommu=off when booting with kexec.
The problem here was that the IOMMU driver bailed out early without
disabling the iommu hardware, if it was enabled in the old kernel
- The Rockchip IOMMU driver is now available on ARM64
- Align the return value of the iommu_ops->device_group call-backs to
not miss error values
- Preempt-disable optimizations in the Intel VT-d and common IOVA
code to help Linux-RT
- Various other small cleanups and fixes"
* tag 'iommu-updates-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (60 commits)
iommu/vt-d: Constify intel_dma_ops
iommu: Warn once when device_group callback returns NULL
iommu/omap: Return ERR_PTR in device_group call-back
iommu: Return ERR_PTR() values from device_group call-backs
iommu/s390: Use iommu_group_get_for_dev() in s390_iommu_add_device()
iommu/vt-d: Don't disable preemption while accessing deferred_flush()
iommu/iova: Don't disable preempt around this_cpu_ptr()
iommu/arm-smmu-v3: Add workaround for Cavium ThunderX2 erratum #126
iommu/arm-smmu-v3: Enable ACPI based HiSilicon CMD_PREFETCH quirk(erratum 161010701)
iommu/arm-smmu-v3: Add workaround for Cavium ThunderX2 erratum #74
ACPI/IORT: Fixup SMMUv3 resource size for Cavium ThunderX2 SMMUv3 model
iommu/arm-smmu-v3, acpi: Add temporary Cavium SMMU-V3 IORT model number definitions
iommu/io-pgtable-arm: Use dma_wmb() instead of wmb() when publishing table
iommu/io-pgtable: depend on !GENERIC_ATOMIC64 when using COMPILE_TEST with LPAE
iommu/arm-smmu-v3: Remove io-pgtable spinlock
iommu/arm-smmu: Remove io-pgtable spinlock
iommu/io-pgtable-arm-v7s: Support lockless operation
iommu/io-pgtable-arm: Support lockless operation
iommu/io-pgtable: Introduce explicit coherency
iommu/io-pgtable-arm-v7s: Refactor split_blk_unmap
...
Cavium ThunderX2 SMMU doesn't support MSI and also doesn't have unique irq
lines for gerror, eventq and cmdq-sync.
New named irq "combined" is set as a errata workaround, which allows to
share the irq line by register single irq handler for all the interrupts.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Geetha sowjanya <gakula@caviumnetworks.com>
[will: reworked irq equality checking and added SPI check]
Signed-off-by: Will Deacon <will.deacon@arm.com>
HiSilicon SMMUv3 on Hip06/Hip07 platforms doesn't support CMD_PREFETCH
command. The dt based support for this quirk is already present in the
driver(hisilicon,broken-prefetch-cmd). This adds ACPI support for the
quirk using the IORT smmu model number.
Signed-off-by: shameer <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: hanjun <guohanjun@huawei.com>
[will: rewrote patch]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cavium ThunderX2 SMMU implementation doesn't support page 1 register space
and PAGE0_REGS_ONLY option is enabled as an errata workaround.
This option when turned on, replaces all page 1 offsets used for
EVTQ_PROD/CONS, PRIQ_PROD/CONS register access with page 0 offsets.
SMMU resource size checks are now based on SMMU option PAGE0_REGS_ONLY,
since resource size can be either 64k/128k.
For this, arm_smmu_device_dt_probe/acpi_probe has been moved before
platform_get_resource call, so that SMMU options are set beforehand.
Signed-off-by: Linu Cherian <linu.cherian@cavium.com>
Signed-off-by: Geetha Sowjanya <geethasowjanya.akula@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some Cavium Thunder CPUs suffer a problem where a KVM guest may
inadvertently cause the host kernel to quit receiving interrupts.
Use the Group-0/1 trapping in order to deal with it.
[maz]: Adapted patch to the Group-0/1 trapping, reworked commit log
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
In order to work around Cortex-A73 erratum 858921 in a subsequent
patch, add the required capability that advertise the erratum.
As the configuration option it depends on is not present yet,
this has no immediate effect.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On Qualcomm Datacenter Technologies QDF2400 SoCs, the ITS hardware
implementation uses 16Bytes for Interrupt Translation Entry (ITE),
but reports an incorrect value of 8Bytes in GITS_TYPER.ITTE_size.
It might cause kernel memory corruption depending on the number
of MSI(x) that are configured and the amount of memory that has
been allocated for ITEs in its_create_device().
This patch fixes the potential memory corruption by setting the
correct ITE size to 16Bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Qualcomm Datacenter Technologies Falkor v1 CPU may allocate TLB entries
using an incorrect ASID when TTBRx_EL1 is being updated. When the erratum
is triggered, page table entries using the new translation table base
address (BADDR) will be allocated into the TLB using the old ASID. All
circumstances leading to the incorrect ASID being cached in the TLB arise
when software writes TTBRx_EL1[ASID] and TTBRx_EL1[BADDR], a memory
operation is in the process of performing a translation using the specific
TTBRx_EL1 being written, and the memory operation uses a translation table
descriptor designated as non-global. EL2 and EL3 code changing the EL1&0
ASID is not subject to this erratum because hardware is prohibited from
performing translations from an out-of-context translation regime.
Consider the following pseudo code.
write new BADDR and ASID values to TTBRx_EL1
Replacing the above sequence with the one below will ensure that no TLB
entries with an incorrect ASID are used by software.
write reserved value to TTBRx_EL1[ASID]
ISB
write new value to TTBRx_EL1[BADDR]
ISB
write new value to TTBRx_EL1[ASID]
ISB
When the above sequence is used, page table entries using the new BADDR
value may still be incorrectly allocated into the TLB using the reserved
ASID. Yet this will not reduce functionality, since TLB entries incorrectly
tagged with the reserved ASID will never be hit by a later instruction.
Based on work by Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we have a workaround for Hisilicon erratum 161010101, notes
this in the arm64 silicon-errata document.
The new config option is too long to fit in the existing kconfig column,
so this is widened to accomodate it. At the same time, an existing
whitespace error is corrected, and the existing pattern of a line space
between vendors is enforced for recent additions.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, reword commit message, rework table]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
During a TLB invalidate sequence targeting the inner shareable domain,
Falkor may prematurely complete the DSB before all loads and stores using
the old translation are observed. Instruction fetches are not subject to
the conditions of this erratum. If the original code sequence includes
multiple TLB invalidate instructions followed by a single DSB, onle one of
the TLB instructions needs to be repeated to work around this erratum.
While the erratum only applies to cases in which the TLBI specifies the
inner-shareable domain (*IS form of TLBI) and the DSB is ISH form or
stronger (OSH, SYS), this changes applies the workaround overabundantly--
to local TLBI, DSB NSH sequences as well--for simplicity.
Based on work by Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJX7k31AAoJELescNyEwWM0XX0H/iOaWCfKlWOhvBsStGUCsLrK
XryTzQT2KjdnLKf3jwP+1ateCuBR5ROurYxoDCX5/7mD63c5KiI338Vbv61a1lE1
AAwjt1stmQVUg/j+kqnuQwB/0DYg+2C8se3D3q5Iyn7zc19cDZJEGcBHNrvLMufc
XgHrgHgl/rzBDDlHJXleknDFge/MfhU5/Q1vJMRRb4JYrpAtmIokzCO75CYMRcCT
ND2QbmppKtsyuFPGUTVbAFzJlP6dGKb3eruYta7/ct5d0pJQxav3u98D2yWGfjdM
YaYq1EmX5Pol7rWumqLtk0+mA9yCFcKLLc+PrJu20Vx0UkvOq8G8Xt70sHNvZU8=
=gdPM
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"It's a bit all over the place this time with no "killer feature" to
speak of. Support for mismatched cache line sizes should help people
seeing whacky JIT failures on some SoCs, and the big.LITTLE perf
updates have been a long time coming, but a lot of the changes here
are cleanups.
We stray outside arch/arm64 in a few areas: the arch/arm/ arch_timer
workaround is acked by Russell, the DT/OF bits are acked by Rob, the
arch_timer clocksource changes acked by Marc, CPU hotplug by tglx and
jump_label by Peter (all CC'd).
Summary:
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (100 commits)
arm64: tlbflush.h: add __tlbi() macro
arm64: Kconfig: remove SMP dependence for NUMA
arm64: Kconfig: select OF/ACPI_NUMA under NUMA config
arm64: fix dump_backtrace/unwind_frame with NULL tsk
arm/arm64: arch_timer: Use archdata to indicate vdso suitability
arm64: arch_timer: Work around QorIQ Erratum A-008585
arm64: arch_timer: Add device tree binding for A-008585 erratum
arm64: Correctly bounds check virt_addr_valid
arm64: migrate exception table users off module.h and onto extable.h
arm64: pmu: Hoist pmu platform device name
arm64: pmu: Probe default hw/cache counters
arm64: pmu: add fallback probe table
MAINTAINERS: Update ARM PMU PROFILING AND DEBUGGING entry
arm64: Improve kprobes test for atomic sequence
arm64/kvm: use alternative auto-nop
arm64: use alternative auto-nop
arm64: alternative: add auto-nop infrastructure
arm64: lse: convert lse alternatives NOP padding to use __nops
arm64: barriers: introduce nops and __nops macros for NOP sequences
arm64: sysreg: replace open-coded mrs_s/msr_s with {read,write}_sysreg_s
...
Erratum A-008585 says that the ARM generic timer counter "has the
potential to contain an erroneous value for a small number of core
clock cycles every time the timer value changes". Accesses to TVAL
(both read and write) are also affected due to the implicit counter
read. Accesses to CVAL are not affected.
The workaround is to reread TVAL and count registers until successive
reads return the same value. Writes to TVAL are replaced with an
equivalent write to CVAL.
The workaround is to reread TVAL and count registers until successive reads
return the same value, and when writing TVAL to retry until counter
reads before and after the write return the same value.
The workaround is enabled if the fsl,erratum-a008585 property is found in
the timer node in the device tree. This can be overridden with the
clocksource.arm_arch_timer.fsl-a008585 boot parameter, which allows KVM
users to enable the workaround until a mechanism is implemented to
automatically communicate this information.
This erratum can be found on LS1043A and LS2080A.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Scott Wood <oss@buserror.net>
[will: renamed read macro to reflect that it's not usually unstable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
We already have a workaround for Cortex-A57 erratum #852523,
but Cortex-A72 r0p0 to r0p2 do suffer from the same issue
(known as erratum #853709).
Let's document the fact that we already handle this.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The erratum fixes the hang of ITS SYNC command by avoiding inter node
io and collections/cpu mapping on thunderx dual-socket platform.
This fix is only applicable for Cavium's ThunderX dual-socket platform.
Reviewed-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
MMU-500 erratum #841119 is tickled by a particular set of circumstances
interacting with the next-page prefetcher. Since said prefetcher is
quite dumb and actually detrimental to performance in some cases (by
causing unwanted TLB evictions for non-sequential access patterns), we
lose very little by turning it off, and what we gain is a guarantee that
the erratum is never hit.
As a bonus, the same workaround will also prevent erratum #826419 once
v7 short descriptor support is implemented.
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Due to erratum #27704, the CN88xx SMMUv2 implementation supports only
shared ASID and VMID numberspaces.
This patch ensures that ASID and VMIDs are unique across all SMMU
instances on affected Cavium systems.
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Signed-off-by: Akula Geethasowjanya <Geethasowjanya.Akula@caviumnetworks.com>
[will: commit message, comments and formatting]
Signed-off-by: Will Deacon <will.deacon@arm.com>
On ThunderX T88 pass 1.x through 2.1 parts, broadcast TLBI
instructions may cause the icache to become corrupted if it contains
data for a non-current ASID.
This patch implements the workaround (which invalidates the local
icache when switching the mm) by using code patching.
Signed-off-by: Andrew Pinski <apinski@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
It's not immediately obvious which hardware errata are worked around in
the Linux kernel for an arbitrary kernel tree, so add a file to keep
track of what we're working around.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Shanker Donthineni