* More phys_to_virt conversions
* Improvement of AP management for VSIE (nested virtualization)
ARM64:
* Numerous fixes for the pathological lock inversion issue that
plagued KVM/arm64 since... forever.
* New framework allowing SMCCC-compliant hypercalls to be forwarded
to userspace, hopefully paving the way for some more features
being moved to VMMs rather than be implemented in the kernel.
* Large rework of the timer code to allow a VM-wide offset to be
applied to both virtual and physical counters as well as a
per-timer, per-vcpu offset that complements the global one.
This last part allows the NV timer code to be implemented on
top.
* A small set of fixes to make sure that we don't change anything
affecting the EL1&0 translation regime just after having having
taken an exception to EL2 until we have executed a DSB. This
ensures that speculative walks started in EL1&0 have completed.
* The usual selftest fixes and improvements.
KVM x86 changes for 6.4:
* Optimize CR0.WP toggling by avoiding an MMU reload when TDP is enabled,
and by giving the guest control of CR0.WP when EPT is enabled on VMX
(VMX-only because SVM doesn't support per-bit controls)
* Add CR0/CR4 helpers to query single bits, and clean up related code
where KVM was interpreting kvm_read_cr4_bits()'s "unsigned long" return
as a bool
* Move AMD_PSFD to cpufeatures.h and purge KVM's definition
* Avoid unnecessary writes+flushes when the guest is only adding new PTEs
* Overhaul .sync_page() and .invlpg() to utilize .sync_page()'s optimizations
when emulating invalidations
* Clean up the range-based flushing APIs
* Revamp the TDP MMU's reaping of Accessed/Dirty bits to clear a single
A/D bit using a LOCK AND instead of XCHG, and skip all of the "handle
changed SPTE" overhead associated with writing the entire entry
* Track the number of "tail" entries in a pte_list_desc to avoid having
to walk (potentially) all descriptors during insertion and deletion,
which gets quite expensive if the guest is spamming fork()
* Disallow virtualizing legacy LBRs if architectural LBRs are available,
the two are mutually exclusive in hardware
* Disallow writes to immutable feature MSRs (notably PERF_CAPABILITIES)
after KVM_RUN, similar to CPUID features
* Overhaul the vmx_pmu_caps selftest to better validate PERF_CAPABILITIES
* Apply PMU filters to emulated events and add test coverage to the
pmu_event_filter selftest
x86 AMD:
* Add support for virtual NMIs
* Fixes for edge cases related to virtual interrupts
x86 Intel:
* Don't advertise XTILE_CFG in KVM_GET_SUPPORTED_CPUID if XTILE_DATA is
not being reported due to userspace not opting in via prctl()
* Fix a bug in emulation of ENCLS in compatibility mode
* Allow emulation of NOP and PAUSE for L2
* AMX selftests improvements
* Misc cleanups
MIPS:
* Constify MIPS's internal callbacks (a leftover from the hardware enabling
rework that landed in 6.3)
Generic:
* Drop unnecessary casts from "void *" throughout kvm_main.c
* Tweak the layout of "struct kvm_mmu_memory_cache" to shrink the struct
size by 8 bytes on 64-bit kernels by utilizing a padding hole
Documentation:
* Fix goof introduced by the conversion to rST
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmRNExkUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNyjwf+MkzDael9y9AsOZoqhEZ5OsfQYJ32
Im5ZVYsPRU2K5TuoWql6meIihgclCj1iIU32qYHa2F1WYt2rZ72rJp+HoY8b+TaI
WvF0pvNtqQyg3iEKUBKPA4xQ6mj7RpQBw86qqiCHmlfNt0zxluEGEPxH8xrWcfhC
huDQ+NUOdU7fmJ3rqGitCvkUbCuZNkw3aNPR8dhU8RAWrwRzP2hBOmdxIeo81WWY
XMEpJSijbGpXL9CvM0Jz9nOuMJwZwCCBGxg1vSQq0xTfLySNMxzvWZC2GFaBjucb
j0UOQ7yE0drIZDVhd3sdNslubXXU6FcSEzacGQb9aigMUon3Tem9SHi7Kw==
=S2Hq
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"s390:
- More phys_to_virt conversions
- Improvement of AP management for VSIE (nested virtualization)
ARM64:
- Numerous fixes for the pathological lock inversion issue that
plagued KVM/arm64 since... forever.
- New framework allowing SMCCC-compliant hypercalls to be forwarded
to userspace, hopefully paving the way for some more features being
moved to VMMs rather than be implemented in the kernel.
- Large rework of the timer code to allow a VM-wide offset to be
applied to both virtual and physical counters as well as a
per-timer, per-vcpu offset that complements the global one. This
last part allows the NV timer code to be implemented on top.
- A small set of fixes to make sure that we don't change anything
affecting the EL1&0 translation regime just after having having
taken an exception to EL2 until we have executed a DSB. This
ensures that speculative walks started in EL1&0 have completed.
- The usual selftest fixes and improvements.
x86:
- Optimize CR0.WP toggling by avoiding an MMU reload when TDP is
enabled, and by giving the guest control of CR0.WP when EPT is
enabled on VMX (VMX-only because SVM doesn't support per-bit
controls)
- Add CR0/CR4 helpers to query single bits, and clean up related code
where KVM was interpreting kvm_read_cr4_bits()'s "unsigned long"
return as a bool
- Move AMD_PSFD to cpufeatures.h and purge KVM's definition
- Avoid unnecessary writes+flushes when the guest is only adding new
PTEs
- Overhaul .sync_page() and .invlpg() to utilize .sync_page()'s
optimizations when emulating invalidations
- Clean up the range-based flushing APIs
- Revamp the TDP MMU's reaping of Accessed/Dirty bits to clear a
single A/D bit using a LOCK AND instead of XCHG, and skip all of
the "handle changed SPTE" overhead associated with writing the
entire entry
- Track the number of "tail" entries in a pte_list_desc to avoid
having to walk (potentially) all descriptors during insertion and
deletion, which gets quite expensive if the guest is spamming
fork()
- Disallow virtualizing legacy LBRs if architectural LBRs are
available, the two are mutually exclusive in hardware
- Disallow writes to immutable feature MSRs (notably
PERF_CAPABILITIES) after KVM_RUN, similar to CPUID features
- Overhaul the vmx_pmu_caps selftest to better validate
PERF_CAPABILITIES
- Apply PMU filters to emulated events and add test coverage to the
pmu_event_filter selftest
- AMD SVM:
- Add support for virtual NMIs
- Fixes for edge cases related to virtual interrupts
- Intel AMX:
- Don't advertise XTILE_CFG in KVM_GET_SUPPORTED_CPUID if
XTILE_DATA is not being reported due to userspace not opting in
via prctl()
- Fix a bug in emulation of ENCLS in compatibility mode
- Allow emulation of NOP and PAUSE for L2
- AMX selftests improvements
- Misc cleanups
MIPS:
- Constify MIPS's internal callbacks (a leftover from the hardware
enabling rework that landed in 6.3)
Generic:
- Drop unnecessary casts from "void *" throughout kvm_main.c
- Tweak the layout of "struct kvm_mmu_memory_cache" to shrink the
struct size by 8 bytes on 64-bit kernels by utilizing a padding
hole
Documentation:
- Fix goof introduced by the conversion to rST"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (211 commits)
KVM: s390: pci: fix virtual-physical confusion on module unload/load
KVM: s390: vsie: clarifications on setting the APCB
KVM: s390: interrupt: fix virtual-physical confusion for next alert GISA
KVM: arm64: Have kvm_psci_vcpu_on() use WRITE_ONCE() to update mp_state
KVM: arm64: Acquire mp_state_lock in kvm_arch_vcpu_ioctl_vcpu_init()
KVM: selftests: Test the PMU event "Instructions retired"
KVM: selftests: Copy full counter values from guest in PMU event filter test
KVM: selftests: Use error codes to signal errors in PMU event filter test
KVM: selftests: Print detailed info in PMU event filter asserts
KVM: selftests: Add helpers for PMC asserts in PMU event filter test
KVM: selftests: Add a common helper for the PMU event filter guest code
KVM: selftests: Fix spelling mistake "perrmited" -> "permitted"
KVM: arm64: vhe: Drop extra isb() on guest exit
KVM: arm64: vhe: Synchronise with page table walker on MMU update
KVM: arm64: pkvm: Document the side effects of kvm_flush_dcache_to_poc()
KVM: arm64: nvhe: Synchronise with page table walker on TLBI
KVM: arm64: Handle 32bit CNTPCTSS traps
KVM: arm64: nvhe: Synchronise with page table walker on vcpu run
KVM: arm64: vgic: Don't acquire its_lock before config_lock
KVM: selftests: Add test to verify KVM's supported XCR0
...
Now that the SRCU Kconfig option is unconditionally selected, there is
no longer any point in selecting it. Therefore, remove the "select SRCU"
Kconfig statements from the various KVM Kconfig files.
Acked-by: Sean Christopherson <seanjc@google.com> (x86)
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <kvm@vger.kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org> (arm64)
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Anup Patel <anup@brainfault.org> (riscv)
Acked-by: Heiko Carstens <hca@linux.ibm.com> (s390)
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
All kvm_arch_vm_ioctl() implementations now only deal with "int"
types as return values, so we can change the return type of these
functions to use "int" instead of "long".
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Anup Patel <anup@brainfault.org>
Message-Id: <20230208140105.655814-7-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Change V=1 option to print both short log and full command log.
- Allow V=1 and V=2 to be combined as V=12.
- Make W=1 detect wrong .gitignore files.
- Tree-wide cleanups for unused command line arguments passed to Clang.
- Stop using -Qunused-arguments with Clang.
- Make scripts/setlocalversion handle only correct release tags instead
of any arbitrary annotated tag.
- Create Debian and RPM source packages without cleaning the source tree.
- Various cleanups for packaging.
-----BEGIN PGP SIGNATURE-----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=HpFZ
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Change V=1 option to print both short log and full command log
- Allow V=1 and V=2 to be combined as V=12
- Make W=1 detect wrong .gitignore files
- Tree-wide cleanups for unused command line arguments passed to Clang
- Stop using -Qunused-arguments with Clang
- Make scripts/setlocalversion handle only correct release tags instead
of any arbitrary annotated tag
- Create Debian and RPM source packages without cleaning the source
tree
- Various cleanups for packaging
* tag 'kbuild-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (74 commits)
kbuild: rpm-pkg: remove unneeded KERNELRELEASE from modules/headers_install
docs: kbuild: remove description of KBUILD_LDS_MODULE
.gitattributes: use 'dts' diff driver for *.dtso files
kbuild: deb-pkg: improve the usability of source package
kbuild: deb-pkg: fix binary-arch and clean in debian/rules
kbuild: tar-pkg: use tar rules in scripts/Makefile.package
kbuild: make perf-tar*-src-pkg work without relying on git
kbuild: deb-pkg: switch over to source format 3.0 (quilt)
kbuild: deb-pkg: make .orig tarball a hard link if possible
kbuild: deb-pkg: hide KDEB_SOURCENAME from Makefile
kbuild: srcrpm-pkg: create source package without cleaning
kbuild: rpm-pkg: build binary packages from source rpm
kbuild: deb-pkg: create source package without cleaning
kbuild: add a tool to list files ignored by git
Documentation/llvm: add Chimera Linux, Google and Meta datacenters
setlocalversion: use only the correct release tag for git-describe
setlocalversion: clean up the construction of version output
.gitignore: ignore *.cover and *.mbx
kbuild: remove --include-dir MAKEFLAG from top Makefile
kbuild: fix trivial typo in comment
...
-Wa,-msoft-float is tested with as-option, which will be a problem for
clang with an upcoming change to move as-option to use KBUILD_AFLAGS
instead of KBUILD_CFLAGS due to a lack of '-mno-abicalls' in
KBUILD_AFLAGS at the point that this check occurs; $(cflags-y) is added
to KBUILD_AFLAGS towards the end of this file.
clang: error: ignoring '-fno-PIE' option as it cannot be used with implicit usage of -mabicalls and the N64 ABI [-Werror,-Woption-ignored]
This could be resolved by switching to a cc-option check but
'$(cflags-y)' would need to be added so that '-mno-abicalls' is present
for the test. However, this check is no longer necessary, as
-msoft-float is supported by all supported assembler versions (GNU as
2.25+ and LLVM 11+). Eliminate GAS_HAS_SET_HARDFLOAT and all of its
uses, inlining SET_HARDFLOAT where necessary.
Link: https://lore.kernel.org/202209101939.bvk64Fok-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Allow architectures to opt out of the generic hardware enabling logic,
and opt out on both s390 and PPC, which don't need to manually enable
virtualization as it's always on (when available).
In addition to letting s390 and PPC drop a bit of dead code, this will
hopefully also allow ARM to clean up its related code, e.g. ARM has its
own per-CPU flag to track which CPUs have enable hardware due to the
need to keep hardware enabled indefinitely when pKVM is enabled.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Acked-by: Anup Patel <anup@brainfault.org>
Message-Id: <20221130230934.1014142-50-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop kvm_arch_check_processor_compat() and its support code now that all
architecture implementations are nops.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Farman <farman@linux.ibm.com> # s390
Acked-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-Id: <20221130230934.1014142-33-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop kvm_arch_init() and kvm_arch_exit() now that all implementations
are nops.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com> # s390
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Anup Patel <anup@brainfault.org>
Message-Id: <20221130230934.1014142-30-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call kvm_init() only after _all_ setup is complete, as kvm_init() exposes
/dev/kvm to userspace and thus allows userspace to create VMs (and call
other ioctls).
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221130230934.1014142-24-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Invoke kvm_mips_emulation_init() directly from kvm_mips_init() instead
of bouncing through kvm_init()=>kvm_arch_init(). Functionally, this is
a glorified nop as invoking kvm_arch_init() is the very first action
performed by kvm_init().
Emptying kvm_arch_init() will allow dropping the hook entirely once all
architecture implementations are nops.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221130230934.1014142-23-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that KVM no longer supports trap-and-emulate (see commit 45c7e8af4a
"MIPS: Remove KVM_TE support"), hardcode the MIPS callbacks to the
virtualization callbacks.
Harcoding the callbacks eliminates the technically-unnecessary check on
non-NULL kvm_mips_callbacks in kvm_arch_init(). MIPS has never supported
multiple in-tree modules, i.e. barring an out-of-tree module, where
copying and renaming kvm.ko counts as "out-of-tree", KVM could never
encounter a non-NULL set of callbacks during module init.
The callback check is also subtly broken, as it is not thread safe,
i.e. if there were multiple modules, loading both concurrently would
create a race between checking and setting kvm_mips_callbacks.
Given that out-of-tree shenanigans are not the kernel's responsibility,
hardcode the callbacks to simplify the code.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221130230934.1014142-22-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop kvm_arch_hardware_setup() and kvm_arch_hardware_unsetup() now that
all implementations are nops.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com> # s390
Acked-by: Anup Patel <anup@brainfault.org>
Message-Id: <20221130230934.1014142-10-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Patch series "mm/sparse-vmemmap: Generalise helpers and enable for
LoongArch", v14.
This series is in order to enable sparse-vmemmap for LoongArch. But
LoongArch cannot use generic helpers directly because MIPS&LoongArch need
to call pgd_init()/pud_init()/pmd_init() when populating page tables. So
we adjust the prototypes of p?d_init() to make generic helpers can call
them, then enable sparse-vmemmap with generic helpers, and to be further,
generalise vmemmap_populate_hugepages() for ARM64, X86 and LoongArch.
This patch (of 4):
We are preparing to add sparse vmemmap support to LoongArch. MIPS and
LoongArch need to call pgd_init()/pud_init()/pmd_init() when populating
page tables, so adjust their prototypes to make generic helpers can call
them.
NIOS2 declares pmd_init() but doesn't use, just remove it to avoid build
errors.
Link: https://lkml.kernel.org/r/20221027125253.3458989-1-chenhuacai@loongson.cn
Link: https://lkml.kernel.org/r/20221027125253.3458989-2-chenhuacai@loongson.cn
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Guo Ren <guoren@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Will Deacon <will@kernel.org>
Cc: Xuefeng Li <lixuefeng@loongson.cn>
Cc: Xuerui Wang <kernel@xen0n.name>
Cc: Min Zhou <zhoumin@loongson.cn>
Cc: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
KVM_REQ_UNHALT is now unnecessary because it is replaced by the return
value of kvm_vcpu_block/kvm_vcpu_halt. Remove it.
No functional change intended.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Message-Id: <20220921003201.1441511-13-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_REQ_UNHALT is a weird request that simply reports the value of
kvm_arch_vcpu_runnable() on exit from kvm_vcpu_halt(). Only
MIPS and x86 are looking at it, the others just clear it. Check
the state of the vCPU directly so that the request is handled
as a nop on all architectures.
No functional change intended, except for corner cases where an
event arrive immediately after a signal become pending or after
another similar host-side event.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220921003201.1441511-12-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The motivation of this renaming is to make these variables and related
helper functions less mmu_notifier bound and can also be used for non
mmu_notifier based page invalidation. mmu_invalidate_* was chosen to
better describe the purpose of 'invalidating' a page that those
variables are used for.
- mmu_notifier_seq/range_start/range_end are renamed to
mmu_invalidate_seq/range_start/range_end.
- mmu_notifier_retry{_hva} helper functions are renamed to
mmu_invalidate_retry{_hva}.
- mmu_notifier_count is renamed to mmu_invalidate_in_progress to
avoid confusion with mn_active_invalidate_count.
- While here, also update kvm_inc/dec_notifier_count() to
kvm_mmu_invalidate_begin/end() to match the change for
mmu_notifier_count.
No functional change intended.
Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
Message-Id: <20220816125322.1110439-3-chao.p.peng@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is the order of the page table allocation, not the order of a PGD.
While at it remove unused defintion of _PGD_ORDER in asm-offsets.
Link: https://lkml.kernel.org/r/20220703141203.147893-7-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Guo Ren <guoren@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Xuerui Wang <kernel@xen0n.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
* A couple of fixes when handling an exception while a SError has been delivered
* Workaround for Cortex-A510's single-step erratum
RISCV:
* Make CY, TM, and IR counters accessible in VU mode
* Fix SBI implementation version
x86:
* Report deprecation of x87 features in supported CPUID
* Preparation for fixing an interrupt delivery race on AMD hardware
* Sparse fix
All except POWER and s390:
* Rework guest entry code to correctly mark noinstr areas and fix vtime'
accounting (for x86, this was already mostly correct but not entirely;
for ARM, MIPS and RISC-V it wasn't)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmH+E4AUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNujwf+ON/8pBWyMPdjiY5l5SyNLpRup8Su
zkQoMEDICI7khYUz2bEAjOazFWHmHPsdogAlG82QeJCbFmCqyMb6iX0uWj53BdGP
P2bOM/tXbulvKBBeiTritkUUNO+hBmmSF+57AOJSW+Enhc7HFwk54cuft6f30r+d
JRaEOhPOP34hQ+wFQQhZZh72BaZBqgnrYwZDp1TiC0Wh8v7P4Nf+NFtEgba2nsxC
xfz5PrEhvegtU8Ee9JAF2bAl7851WJq557P2cOpghtUMgh4t6GzCcUOCKIie67oQ
0Vaf+OieAopdT+QNazSEWO9zxl7eTpWjk2hrwsDrgKHAL/YmuWJuSyEYIA==
=C0LZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- A couple of fixes when handling an exception while a SError has
been delivered
- Workaround for Cortex-A510's single-step erratum
RISC-V:
- Make CY, TM, and IR counters accessible in VU mode
- Fix SBI implementation version
x86:
- Report deprecation of x87 features in supported CPUID
- Preparation for fixing an interrupt delivery race on AMD hardware
- Sparse fix
All except POWER and s390:
- Rework guest entry code to correctly mark noinstr areas and fix
vtime' accounting (for x86, this was already mostly correct but not
entirely; for ARM, MIPS and RISC-V it wasn't)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Use ERR_PTR_USR() to return -EFAULT as a __user pointer
KVM: x86: Report deprecated x87 features in supported CPUID
KVM: arm64: Workaround Cortex-A510's single-step and PAC trap errata
KVM: arm64: Stop handle_exit() from handling HVC twice when an SError occurs
KVM: arm64: Avoid consuming a stale esr value when SError occur
RISC-V: KVM: Fix SBI implementation version
RISC-V: KVM: make CY, TM, and IR counters accessible in VU mode
kvm/riscv: rework guest entry logic
kvm/arm64: rework guest entry logic
kvm/x86: rework guest entry logic
kvm/mips: rework guest entry logic
kvm: add guest_state_{enter,exit}_irqoff()
KVM: x86: Move delivery of non-APICv interrupt into vendor code
kvm: Move KVM_GET_XSAVE2 IOCTL definition at the end of kvm.h
In kvm_arch_vcpu_ioctl_run() we use guest_enter_irqoff() and
guest_exit_irqoff() directly, with interrupts masked between these. As
we don't handle any timer ticks during this window, we will not account
time spent within the guest as guest time, which is unfortunate.
Additionally, we do not inform lockdep or tracing that interrupts will
be enabled during guest execution, which caan lead to misleading traces
and warnings that interrupts have been enabled for overly-long periods.
This patch fixes these issues by using the new timing and context
entry/exit helpers to ensure that interrupts are handled during guest
vtime but with RCU watching, with a sequence:
guest_timing_enter_irqoff();
guest_state_enter_irqoff();
< run the vcpu >
guest_state_exit_irqoff();
< take any pending IRQs >
guest_timing_exit_irqoff();
In addition, as guest exits during the "run the vcpu" step are handled
by kvm_mips_handle_exit(), a wrapper function is added which ensures
that such exists are handled with a sequence:
guest_state_exit_irqoff();
< handle the exit >
guest_state_enter_irqoff();
This means that exits which stop the vCPU running will have a redundant
guest_state_enter_irqoff() .. guest_state_exit_irqoff() sequence, which
can be addressed with future rework.
Since instrumentation may make use of RCU, we must also ensure that no
instrumented code is run during the EQS. I've split out the critical
section into a new kvm_mips_enter_exit_vcpu() helper which is marked
noinstr.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Message-Id: <20220201132926.3301912-6-mark.rutland@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix all kernel-doc warnings in mips/kvm/vz.c as reported by the
kernel test robot:
arch/mips/kvm/vz.c:471: warning: Function parameter or member 'out_compare' not described in '_kvm_vz_save_htimer'
arch/mips/kvm/vz.c:471: warning: Function parameter or member 'out_cause' not described in '_kvm_vz_save_htimer'
arch/mips/kvm/vz.c:471: warning: Excess function parameter 'compare' description in '_kvm_vz_save_htimer'
arch/mips/kvm/vz.c:471: warning: Excess function parameter 'cause' description in '_kvm_vz_save_htimer'
arch/mips/kvm/vz.c:1551: warning: No description found for return value of 'kvm_trap_vz_handle_cop_unusable'
arch/mips/kvm/vz.c:1552: warning: expecting prototype for kvm_trap_vz_handle_cop_unusuable(). Prototype was for kvm_trap_vz_handle_cop_unusable() instead
arch/mips/kvm/vz.c:1597: warning: No description found for return value of 'kvm_trap_vz_handle_msa_disabled'
Fixes: c992a4f6a9 ("KVM: MIPS: Implement VZ support")
Fixes: f4474d50c7 ("KVM: MIPS/VZ: Support hardware guest timer")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: kvm@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20211121125451.9489-5-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename kvm_vcpu_block() to kvm_vcpu_halt() in preparation for splitting
the actual "block" sequences into a separate helper (to be named
kvm_vcpu_block()). x86 will use the standalone block-only path to handle
non-halt cases where the vCPU is not runnable.
Rename block_ns to halt_ns to match the new function name.
No functional change intended.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211009021236.4122790-14-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current memslots implementation only allows quick binary search by gfn,
quick lookup by hva is not possible - the implementation has to do a linear
scan of the whole memslots array, even though the operation being performed
might apply just to a single memslot.
This significantly hurts performance of per-hva operations with higher
memslot counts.
Since hva ranges can overlap between memslots an interval tree is needed
for tracking them.
[sean: handle interval tree updates in kvm_replace_memslot()]
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <d66b9974becaa9839be9c4e1a5de97b177b4ac20.1638817640.git.maciej.szmigiero@oracle.com>
Drop the @mem param from kvm_arch_{prepare,commit}_memory_region() now
that its use has been removed in all architectures.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <aa5ed3e62c27e881d0d8bc0acbc1572bc336dc19.1638817640.git.maciej.szmigiero@oracle.com>
Remove an old (circa 2012) kvm_debug from kvm_arch_commit_memory_region()
to print basic information when committing a memslot change. The primary
motivation for removing the kvm_debug is to avoid using @mem, the user
memory region, so that said param can be removed.
Alternatively, the debug message could be converted to use @new, but that
would require synthesizing select state to play nice with the DELETED
case, which will pass NULL for @new in the future. And there's no
argument to be had for dumping generic information in an arch callback,
i.e. if there's a good reason for the debug message, then it belongs in
common KVM code where all architectures can benefit.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <446929a668f6e1346751571b71db41e94e976cdf.1638817639.git.maciej.szmigiero@oracle.com>
Pass the "old" slot to kvm_arch_prepare_memory_region() and force arch
code to handle propagating arch specific data from "new" to "old" when
necessary. This is a baby step towards dynamically allocating "new" from
the get go, and is a (very) minor performance boost on x86 due to not
unnecessarily copying arch data.
For PPC HV, copy the rmap in the !CREATE and !DELETE paths, i.e. for MOVE
and FLAGS_ONLY. This is functionally a nop as the previous behavior
would overwrite the pointer for CREATE, and eventually discard/ignore it
for DELETE.
For x86, copy the arch data only for FLAGS_ONLY changes. Unlike PPC HV,
x86 needs to reallocate arch data in the MOVE case as the size of x86's
allocations depend on the alignment of the memslot's gfn.
Opportunistically tweak kvm_arch_prepare_memory_region()'s param order to
match the "commit" prototype.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
[mss: add missing RISCV kvm_arch_prepare_memory_region() change]
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <67dea5f11bbcfd71e3da5986f11e87f5dd4013f9.1638817639.git.maciej.szmigiero@oracle.com>
As we are about to change the way vcpus are allocated, mandate
the use of kvm_get_vcpu() instead of open-coding the access.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Message-Id: <20211116160403.4074052-3-maz@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All architectures have similar loops iterating over the vcpus,
freeing one vcpu at a time, and eventually wiping the reference
off the vcpus array. They are also inconsistently taking
the kvm->lock mutex when wiping the references from the array.
Make this code common, which will simplify further changes.
The locking is dropped altogether, as this should only be called
when there is no further references on the kvm structure.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Message-Id: <20211116160403.4074052-2-maz@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It doesn't make sense to return the recommended maximum number of
vCPUs which exceeds the maximum possible number of vCPUs.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211116163443.88707-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- removed support for Netlogic SOCs
- fixes and cleanup
-----BEGIN PGP SIGNATURE-----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=mvn0
-----END PGP SIGNATURE-----
Merge tag 'mips_5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- added printing of CPU options for /proc/cpuinfo
- removed support for Netlogic SOCs
- fixes and cleanup
* tag 'mips_5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Cobalt: Explain GT64111 early PCI fixup
mips: fix HUGETLB function without THP enabled
mips: cm: Convert to bitfield API to fix out-of-bounds access
MIPS: Remove NETLOGIC support
MIPS: kernel: proc: add CPU option reporting
MIPS: kernel: proc: use seq_puts instead of seq_printf
MIPS: kernel: proc: fix trivial style errors
MIPS: Fix assembly error from MIPSr2 code used within MIPS_ISA_ARCH_LEVEL
MIPS: octeon: Remove unused functions
MIPS: Loongson64: Add of_node_put() before break
bcm47xx: Replace printk(KERN_ALERT ... pci_devname(dev)) with pci_alert()
bcm47xx: Get rid of redundant 'else'
MIPS: sni: Fix the build
MIPS: Avoid macro redefinitions
MIPS: loongson64: Fix no screen display during boot-up
MIPS: loongson64: make CPU_LOONGSON64 depends on MIPS_FP_SUPPORT
KVM_MAX_VCPU_ID is not specifying the highest allowed vcpu-id, but the
number of allowed vcpu-ids. This has already led to confusion, so
rename KVM_MAX_VCPU_ID to KVM_MAX_VCPU_IDS to make its semantics more
clear
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210913135745.13944-3-jgross@suse.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Page ownership tracking between host EL1 and EL2
- Rely on userspace page tables to create large stage-2 mappings
- Fix incompatibility between pKVM and kmemleak
- Fix the PMU reset state, and improve the performance of the virtual PMU
- Move over to the generic KVM entry code
- Address PSCI reset issues w.r.t. save/restore
- Preliminary rework for the upcoming pKVM fixed feature
- A bunch of MM cleanups
- a vGIC fix for timer spurious interrupts
- Various cleanups
s390:
- enable interpretation of specification exceptions
- fix a vcpu_idx vs vcpu_id mixup
x86:
- fast (lockless) page fault support for the new MMU
- new MMU now the default
- increased maximum allowed VCPU count
- allow inhibit IRQs on KVM_RUN while debugging guests
- let Hyper-V-enabled guests run with virtualized LAPIC as long as they
do not enable the Hyper-V "AutoEOI" feature
- fixes and optimizations for the toggling of AMD AVIC (virtualized LAPIC)
- tuning for the case when two-dimensional paging (EPT/NPT) is disabled
- bugfixes and cleanups, especially with respect to 1) vCPU reset and
2) choosing a paging mode based on CR0/CR4/EFER
- support for 5-level page table on AMD processors
Generic:
- MMU notifier invalidation callbacks do not take mmu_lock unless necessary
- improved caching of LRU kvm_memory_slot
- support for histogram statistics
- add statistics for halt polling and remote TLB flush requests
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmE2CIAUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMyqwf+Ky2WoThuQ9Ra0r/m8pUTAx5+gsAf
MmG24rNLE+26X0xuBT9Q5+etYYRLrRTWJvo5cgHooz7muAYW6scR+ho5xzvLTAxi
DAuoijkXsSdGoFCp0OMUHiwG3cgY5N7feTEwLPAb2i6xr/l6SZyCP4zcwiiQbJ2s
UUD0i3rEoNQ02/hOEveud/ENxzUli9cmmgHKXR3kNgsJClSf1fcuLnhg+7EGMhK9
+c2V+hde5y0gmEairQWm22MLMRolNZ5NL4kjykiNh2M5q9YvbHe5+f/JmENlNZMT
bsUQT6Ry1ukuJ0V59rZvUw71KknPFzZ3d6HgW4pwytMq6EJKiISHzRbVnQ==
=FCAB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- Page ownership tracking between host EL1 and EL2
- Rely on userspace page tables to create large stage-2 mappings
- Fix incompatibility between pKVM and kmemleak
- Fix the PMU reset state, and improve the performance of the virtual
PMU
- Move over to the generic KVM entry code
- Address PSCI reset issues w.r.t. save/restore
- Preliminary rework for the upcoming pKVM fixed feature
- A bunch of MM cleanups
- a vGIC fix for timer spurious interrupts
- Various cleanups
s390:
- enable interpretation of specification exceptions
- fix a vcpu_idx vs vcpu_id mixup
x86:
- fast (lockless) page fault support for the new MMU
- new MMU now the default
- increased maximum allowed VCPU count
- allow inhibit IRQs on KVM_RUN while debugging guests
- let Hyper-V-enabled guests run with virtualized LAPIC as long as
they do not enable the Hyper-V "AutoEOI" feature
- fixes and optimizations for the toggling of AMD AVIC (virtualized
LAPIC)
- tuning for the case when two-dimensional paging (EPT/NPT) is
disabled
- bugfixes and cleanups, especially with respect to vCPU reset and
choosing a paging mode based on CR0/CR4/EFER
- support for 5-level page table on AMD processors
Generic:
- MMU notifier invalidation callbacks do not take mmu_lock unless
necessary
- improved caching of LRU kvm_memory_slot
- support for histogram statistics
- add statistics for halt polling and remote TLB flush requests"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (210 commits)
KVM: Drop unused kvm_dirty_gfn_invalid()
KVM: x86: Update vCPU's hv_clock before back to guest when tsc_offset is adjusted
KVM: MMU: mark role_regs and role accessors as maybe unused
KVM: MIPS: Remove a "set but not used" variable
x86/kvm: Don't enable IRQ when IRQ enabled in kvm_wait
KVM: stats: Add VM stat for remote tlb flush requests
KVM: Remove unnecessary export of kvm_{inc,dec}_notifier_count()
KVM: x86/mmu: Move lpage_disallowed_link further "down" in kvm_mmu_page
KVM: x86/mmu: Relocate kvm_mmu_page.tdp_mmu_page for better cache locality
Revert "KVM: x86: mmu: Add guest physical address check in translate_gpa()"
KVM: x86/mmu: Remove unused field mmio_cached in struct kvm_mmu_page
kvm: x86: Increase KVM_SOFT_MAX_VCPUS to 710
kvm: x86: Increase MAX_VCPUS to 1024
kvm: x86: Set KVM_MAX_VCPU_ID to 4*KVM_MAX_VCPUS
KVM: VMX: avoid running vmx_handle_exit_irqoff in case of emulation
KVM: x86/mmu: Don't freak out if pml5_root is NULL on 4-level host
KVM: s390: index kvm->arch.idle_mask by vcpu_idx
KVM: s390: Enable specification exception interpretation
KVM: arm64: Trim guest debug exception handling
KVM: SVM: Add 5-level page table support for SVM
...
This fix a build warning:
arch/mips/kvm/vz.c: In function '_kvm_vz_restore_htimer':
>> arch/mips/kvm/vz.c:392:10: warning: variable 'freeze_time' set but not used [-Wunused-but-set-variable]
392 | ktime_t freeze_time;
| ^~~~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Message-Id: <20210406024911.2008046-1-chenhuacai@loongson.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
./arch/mips/kernel/uprobes.c:261:8-9: WARNING: return of 0/1 in function
'arch_uprobe_skip_sstep' with return type bool
./arch/mips/kernel/uprobes.c:78:10-11: WARNING: return of 0/1 in
function 'is_trap_insn' with return type bool
./arch/mips/kvm/mmu.c:489:9-10: WARNING: return of 0/1 in function
'kvm_test_age_gfn' with return type bool
./arch/mips/kvm/mmu.c:445:8-9: WARNING: return of 0/1 in function
'kvm_unmap_gfn_range' with return type bool
Signed-off-by: Huilong Deng <denghuilong@cdjrlc.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add new types of KVM stats, linear and logarithmic histogram.
Histogram are very useful for observing the value distribution
of time or size related stats.
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210802165633.1866976-2-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
You can use kvm-y instead of kvm-objs to create the composite module.
kvm-$(CONFIG_...) looks cleaner.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
As Documentation/kbuild/makefiles.rst says, EXTRA_CFLAGS is deprecated.
Replace it with ccflags-y.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- Ingenic fixes/improvments
- other fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=j2kH
-----END PGP SIGNATURE-----
Merge tag 'mips_5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- add support for OpeneEmbed SOM9331 board
- Ingenic fixes/improvments
- other fixes and cleanups
* tag 'mips_5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (39 commits)
MIPS: Fix PKMAP with 32-bit MIPS huge page support
MIPS: CI20: Add second percpu timer for SMP.
MIPS: CI20: Reduce clocksource to 750 kHz.
MIPS: Ingenic: Add MAC syscon nodes for Ingenic SoCs.
dt-bindings: clock: Add documentation for MAC PHY control bindings.
MIPS: X1830: Respect cell count of common properties.
MIPS: set mips32r5 for virt extensions
MIPS: loongsoon64: Reserve memory below starting pfn to prevent Oops
MIPS: MT extensions are not available on MIPS32r1
mips/kvm: Use BUG_ON instead of if condition followed by BUG
MIPS: OCTEON: octeon-usb: Use devm_platform_get_and_ioremap_resource()
MIPS: add PMD table accounting into MIPS'pmd_alloc_one
MIPS: Loongson64: fix spelling of SPDX tag
MIPS: ingenic: rs90: Add dedicated VRAM memory region
MIPS: ingenic: gcw0: Set codec to cap-less mode for FM radio
MIPS: ingenic: jz4780: Fix I2C nodes to match DT doc
MIPS: ingenic: Select CPU_SUPPORTS_CPUFREQ && MIPS_EXTERNAL_TIMER
MIPS: Kconfig: ingenic: Ensure MACH_INGENIC_GENERIC selects all SoCs
MIPS: cpu-probe: Fix FPU detection on Ingenic JZ4760(B)
MIPS: boot: Support specifying UART port on Ingenic SoCs
...
To remove code duplication, use the binary stats descriptors in the
implementation of the debugfs interface for statistics. This unifies
the definition of statistics for the binary and debugfs interfaces.
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-8-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a VCPU ioctl to get a statistics file descriptor by which a read
functionality is provided for userspace to read out VCPU stats header,
descriptors and data.
Define VCPU statistics descriptors and header for all architectures.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com> #arm64
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-5-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a VM ioctl to get a statistics file descriptor by which a read
functionality is provided for userspace to read out VM stats header,
descriptors and data.
Define VM statistics descriptors and header for all architectures.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com> #arm64
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-4-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This commit defines the API for userspace and prepare the common
functionalities to support per VM/VCPU binary stats data readings.
The KVM stats now is only accessible by debugfs, which has some
shortcomings this change series are supposed to fix:
1. The current debugfs stats solution in KVM could be disabled
when kernel Lockdown mode is enabled, which is a potential
rick for production.
2. The current debugfs stats solution in KVM is organized as "one
stats per file", it is good for debugging, but not efficient
for production.
3. The stats read/clear in current debugfs solution in KVM are
protected by the global kvm_lock.
Besides that, there are some other benefits with this change:
1. All KVM VM/VCPU stats can be read out in a bulk by one copy
to userspace.
2. A schema is used to describe KVM statistics. From userspace's
perspective, the KVM statistics are self-describing.
3. With the fd-based solution, a separate telemetry would be able
to read KVM stats in a less privileged environment.
4. After the initial setup by reading in stats descriptors, a
telemetry only needs to read the stats data itself, no more
parsing or setup is needed.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com> #arm64
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-3-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Generic KVM stats are those collected in architecture independent code
or those supported by all architectures; put all generic statistics in
a separate structure. This ensures that they are defined the same way
in the statistics API which is being added, removing duplication among
different architectures in the declaration of the descriptors.
No functional change intended.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-2-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
BUG_ON uses unlikely in if(), it can be optimized at compile time.
Usually, the condition in if() is not satisfied. In my opinion,
this can improve the efficiency of the multi-stage pipeline.
Signed-off-by: zhouchuangao <zhouchuangao@vivo.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- Stage-2 isolation for the host kernel when running in protected mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation,
zap under read lock, enable/disably dirty page logging under
read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing
the architecture-specific code
- Some selftests improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmCJ13kUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroM1HAgAqzPxEtiTPTFeFJV5cnPPJ3dFoFDK
y/juZJUQ1AOtvuWzzwuf175ewkv9vfmtG6rVohpNSkUlJYeoc6tw7n8BTTzCVC1b
c/4Dnrjeycr6cskYlzaPyV6MSgjSv5gfyj1LA5UEM16LDyekmaynosVWY5wJhju+
Bnyid8l8Utgz+TLLYogfQJQECCrsU0Wm//n+8TWQgLf1uuiwshU5JJe7b43diJrY
+2DX+8p9yWXCTz62sCeDWNahUv8AbXpMeJ8uqZPYcN1P0gSEUGu8xKmLOFf9kR7b
M4U1Gyz8QQbjd2lqnwiWIkvRLX6gyGVbq2zH0QbhUe5gg3qGUX7JjrhdDQ==
=AXUi
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"This is a large update by KVM standards, including AMD PSP (Platform
Security Processor, aka "AMD Secure Technology") and ARM CoreSight
(debug and trace) changes.
ARM:
- CoreSight: Add support for ETE and TRBE
- Stage-2 isolation for the host kernel when running in protected
mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- AMD PSP driver changes
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation, zap under
read lock, enable/disably dirty page logging under read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing the
architecture-specific code
- a handful of "Get rid of oprofile leftovers" patches
- Some selftests improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (379 commits)
KVM: selftests: Speed up set_memory_region_test
selftests: kvm: Fix the check of return value
KVM: x86: Take advantage of kvm_arch_dy_has_pending_interrupt()
KVM: SVM: Skip SEV cache flush if no ASIDs have been used
KVM: SVM: Remove an unnecessary prototype declaration of sev_flush_asids()
KVM: SVM: Drop redundant svm_sev_enabled() helper
KVM: SVM: Move SEV VMCB tracking allocation to sev.c
KVM: SVM: Explicitly check max SEV ASID during sev_hardware_setup()
KVM: SVM: Unconditionally invoke sev_hardware_teardown()
KVM: SVM: Enable SEV/SEV-ES functionality by default (when supported)
KVM: SVM: Condition sev_enabled and sev_es_enabled on CONFIG_KVM_AMD_SEV=y
KVM: SVM: Append "_enabled" to module-scoped SEV/SEV-ES control variables
KVM: SEV: Mask CPUID[0x8000001F].eax according to supported features
KVM: SVM: Move SEV module params/variables to sev.c
KVM: SVM: Disable SEV/SEV-ES if NPT is disabled
KVM: SVM: Free sev_asid_bitmap during init if SEV setup fails
KVM: SVM: Zero out the VMCB array used to track SEV ASID association
x86/sev: Drop redundant and potentially misleading 'sev_enabled'
KVM: x86: Move reverse CPUID helpers to separate header file
KVM: x86: Rename GPR accessors to make mode-aware variants the defaults
...
Move MIPS to the gfn-based MMU notifier APIs, which do the hva->gfn
lookup in common code, and whose code is nearly identical to MIPS'
lookup.
No meaningful functional change intended, though the exact order of
operations is slightly different since the memslot lookups occur before
calling into arch code.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Return 1 from kvm_unmap_hva_range and kvm_set_spte_hva if a flush is
needed, so that the generic code can coalesce the flushes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds