This removes the relocate_initrd() implementation and invocation, which are
no longer needed now that the placement of the initrd is guaranteed to be
covered by the linear mapping.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Instead of going out of our way to relocate the initrd if it turns out
to occupy memory that is not covered by the linear mapping, just add the
initrd to the linear mapping. This puts the burden on the bootloader to
pass initrd= and mem= options that are mutually consistent.
Note that, since the placement of the linear region in the PA space is
also dependent on the placement of the kernel Image, which may reside
anywhere in memory, we may still end up with a situation where the initrd
and the kernel Image are simply too far apart to be covered by the linear
region.
Since we now leave it up to the bootloader to pass the initrd in memory
that is guaranteed to be accessible by the kernel, add a mention of this to
the arm64 boot protocol specification as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This reverts commit 36e5cd6b89, since the
section alignment is now guaranteed by construction when choosing the
value of memstart_addr.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This redefines ARM64_MEMSTART_ALIGN in terms of the minimal alignment
required by sparsemem vmemmap. This comes down to using 1 GB for all
translation granules if CONFIG_SPARSEMEM_VMEMMAP is enabled.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
After choosing memstart_addr to be the highest multiple of
ARM64_MEMSTART_ALIGN less than or equal to the first usable physical memory
address, we clip the memblocks to the maximum size of the linear region.
Since the kernel may be high up in memory, we take care not to clip the
kernel itself, which means we have to clip some memory from the bottom if
this occurs, to ensure that the distance between the first and the last
usable physical memory address can be covered by the linear region.
However, we fail to update memstart_addr if this clipping from the bottom
occurs, which means that we may still end up with virtual addresses that
wrap into the userland range. So increment memstart_addr as appropriate to
prevent this from happening.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, we check two pointers: cpu_ops and cpu_suspend on every idle
state entry. These pointers check can be avoided:
If cpu_ops has not been registered, arm_cpuidle_init() will return
-EOPNOTSUPP, so arm_cpuidle_suspend() will never have chance to
run. In other word, the cpu_ops check can be avoid.
Similarly, the cpu_suspend check could be avoided in this hot path by
moving it into arm_cpuidle_init().
I measured the 4096 * time from arm_cpuidle_suspend entry point to the
cpu_psci_cpu_suspend entry point. HW platform is Marvell BG4CT STB
board.
1. only one shell, no other process, hot-unplug secondary cpus, execute
the following cmd
while true
do
sleep 0.2
done
before the patch: 1581220ns
after the patch: 1579630ns
reduced by 0.1%
2. only one shell, no other process, hot-unplug secondary cpus, execute
the following cmd
while true
do
md5sum /tmp/testfile
sleep 0.2
done
NOTE: the testfile size should be larger than L1+L2 cache size
before the patch: 1961960ns
after the patch: 1912500ns
reduced by 2.5%
So the more complex the system load, the bigger the improvement.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are some new cpu features which can be identified by id_aa64mmfr2,
this patch appends all fields of it.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull ARM fixes from Russell King:
"A couple of small fixes, and wiring up the new syscalls which appeared
during the merge window"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8550/1: protect idiv patching against undefined gcc behavior
ARM: wire up preadv2 and pwritev2 syscalls
ARM: SMP enable of cache maintanence broadcast
Pull parisc fixes from Helge Deller:
"Since commit 0de798584b ("parisc: Use generic extable search and
sort routines") module loading is boken on parisc, because the parisc
module loader wasn't prepared for the new R_PARISC_PCREL32 relocations.
In addition, due to that breakage, Mikulas Patocka noticed that
handling exceptions from modules probably never worked on parisc. It
was just masked by the fact that exceptions from modules don't happen
during normal use.
This patch series fixes those issues and survives the tests of the
lib/test_user_copy kernel module test. Some patches are tagged for
stable"
* 'parisc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Update comment regarding relative extable support
parisc: Unbreak handling exceptions from kernel modules
parisc: Fix kernel crash with reversed copy_from_user()
parisc: Avoid function pointers for kernel exception routines
parisc: Handle R_PARISC_PCREL32 relocations in kernel modules
- intel_pstate fixes for two issues exposed by the recent switch
over from using timers and for one issue introduced during the
4.4 cycle plus new comments describing data structures used by
the driver (Rafael Wysocki, Srinivas Pandruvada).
- intel_idle fixes related to CPU offline/online (Richard Cochran).
- intel_idle support (new CPU IDs and state definitions mostly) for
Skylake-X and Kabylake processors (Len Brown).
- PCC mailbox driver fix for an out-of-bounds memory access that
may cause the kernel to panic() (Shanker Donthineni).
- New (missing) CPU ID for one apparently overlooked Haswell model
in the Intel RAPL power capping driver (Srinivas Pandruvada).
- Fix for the PM core's wakeup IRQs framework to make it work after
wakeup settings reconfiguration from sysfs (Grygorii Strashko).
- Runtime PM documentation update to make it describe what needs
to be done during device removal more precisely (Krzysztof
Kozlowski).
- Stale comment removal cleanup in the cpufreq-dt driver (Viresh
Kumar).
- turbostat utility fixes and support for Broxton, Skylake-X
and Kabylake processors (Len Brown).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=f4MM
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Fixes for some issues discovered after recent changes and for some
that have just been found lately regardless of those changes
(intel_pstate, intel_idle, PM core, mailbox/pcc, turbostat) plus
support for some new CPU models (intel_idle, Intel RAPL driver,
turbostat) and documentation updates (intel_pstate, PM core).
Specifics:
- intel_pstate fixes for two issues exposed by the recent switch over
from using timers and for one issue introduced during the 4.4 cycle
plus new comments describing data structures used by the driver
(Rafael Wysocki, Srinivas Pandruvada).
- intel_idle fixes related to CPU offline/online (Richard Cochran).
- intel_idle support (new CPU IDs and state definitions mostly) for
Skylake-X and Kabylake processors (Len Brown).
- PCC mailbox driver fix for an out-of-bounds memory access that may
cause the kernel to panic() (Shanker Donthineni).
- New (missing) CPU ID for one apparently overlooked Haswell model in
the Intel RAPL power capping driver (Srinivas Pandruvada).
- Fix for the PM core's wakeup IRQs framework to make it work after
wakeup settings reconfiguration from sysfs (Grygorii Strashko).
- Runtime PM documentation update to make it describe what needs to
be done during device removal more precisely (Krzysztof Kozlowski).
- Stale comment removal cleanup in the cpufreq-dt driver (Viresh
Kumar).
- turbostat utility fixes and support for Broxton, Skylake-X and
Kabylake processors (Len Brown)"
* tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
...
Update the comment to reflect the changes of commit 0de7985 (parisc: Use
generic extable search and sort routines).
Signed-off-by: Helge Deller <deller@gmx.de>
Handling exceptions from modules never worked on parisc.
It was just masked by the fact that exceptions from modules
don't happen during normal use.
When a module triggers an exception in get_user() we need to load the
main kernel dp value before accessing the exception_data structure, and
afterwards restore the original dp value of the module on exit.
Noticed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
The kernel module testcase (lib/test_user_copy.c) exhibited a kernel
crash on parisc if the parameters for copy_from_user were reversed
("illegal reversed copy_to_user" testcase).
Fix this potential crash by checking the fault handler if the faulting
address is in the exception table.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Cc: Kees Cook <keescook@chromium.org>
We want to avoid the kernel module loader to create function pointers
for the kernel fixup routines of get_user() and put_user(). Changing
the external reference from function type to int type fixes this.
This unbreaks exception handling for get_user() and put_user() when
called from a kernel module.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Commit 0de7985 (parisc: Use generic extable search and sort routines)
changed the exception tables to use 32bit relative offsets.
This patch now adds support to the kernel module loader to handle such
R_PARISC_PCREL32 relocations for 32- and 64-bit modules.
Signed-off-by: Helge Deller <deller@gmx.de>
* pm-core:
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
PM / runtime: Document steps for device removal
* powercap:
powercap: intel_rapl: Add missing Haswell model
* pm-tools:
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
It was reported that a kernel with CONFIG_ARM_PATCH_IDIV=y stopped
booting when compiled with the upcoming gcc 6. Turns out that turning
a function address into a writable array is undefined and gcc 6 decided
it was OK to omit the store to the first word of the function while
still preserving the store to the second word.
Even though gcc 6 is now fixed to behave more coherently, it is a
mystery that gcc 4 and gcc 5 actually produce wanted code in the kernel.
And in fact the reduced test case to illustrate the issue does indeed
break with gcc < 6 as well.
In any case, let's guard the kernel against undefined compiler behavior
by hiding the nature of the array location as suggested by gcc
developers.
Reference: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=70128
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reported-by: Marcin Juszkiewicz <mjuszkiewicz@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org # v4.5
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some processors use the Interrupt Response Time Limit (IRTL) MSR value
to describe the maximum IRQ response time latency for deep
package C-states. (Though others have the register, but do not use it)
Lets print it out to give insight into the cases where it is used.
IRTL begain in SNB, with PC3/PC6/PC7, and HSW added PC8/PC9/PC10.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Let's see if anybody even notices. I doubt anybody uses this, and it
does expose addresses that should be randomized, so let's just remove
the code. It's old and traditional, and it used to be cute, but we
should have removed this long ago.
If it turns out anybody notices and this breaks something, we'll have to
revert this, and maybe we'll end up using other approaches instead
(using %pK or similar). But removing unnecessary code is always the
preferred option.
Noted-by: Emrah Demir <ed@abdsec.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
others are usual stable material.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXA8x6AAoJEL/70l94x66D0x8H/RcBnc75994RQ++WmHSvD9GF
yruGB8soLDdjX+Oceol0aEPHokrBu3JtcdoTBe0GwbCKV/F5NkQZ4EfLxDtR3tte
7ILkPULLy5GElFpJNQuT4pmXzTEspFvXpqHhFik7WVBga3W9wMFQcjbrgmGBUzLE
p2aJVhZyErpKxGFkUYWhDnlqWsguTTIzv/pqNhLY4VVc0UrXN9AA0fq9RkvgU3KS
Hxk4/A6SV/b7dyzvttzITww0f1iu8FmlLj2TXapIEoOz7AnInD6KIN0RYpxbDjxN
bEzEfpahUtuDeM87/t2kHEj0Gn09iHK7/BbCC1Hrwo1CQhbAQ/D0GIvqYAQixf4=
=NugZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Miscellaneous bugfixes.
The ARM and s390 fixes are for new regressions from the merge window,
others are usual stable material"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
compiler-gcc: disable -ftracer for __noclone functions
kvm: x86: make lapic hrtimer pinned
s390/mm/kvm: fix mis-merge in gmap handling
kvm: set page dirty only if page has been writable
KVM: x86: reduce default value of halt_poll_ns parameter
KVM: Hyper-V: do not do hypercall userspace exits if SynIC is disabled
KVM: x86: Inject pending interrupt even if pending nmi exist
arm64: KVM: Register CPU notifiers when the kernel runs at HYP
arm64: kvm: 4.6-rc1: Fix VTCR_EL2 VS setting
When a vCPU runs on a nohz_full core, the hrtimer used by
the lapic emulation code can be migrated to another core.
When this happens, it's possible to observe milisecond
latency when delivering timer IRQs to KVM guests.
The huge latency is mainly due to the fact that
apic_timer_fn() expects to run during a kvm exit. It
sets KVM_REQ_PENDING_TIMER and let it be handled on kvm
entry. However, if the timer fires on a different core,
we have to wait until the next kvm exit for the guest
to see KVM_REQ_PENDING_TIMER set.
This problem became visible after commit 9642d18ee. This
commit changed the timer migration code to always attempt
to migrate timers away from nohz_full cores. While it's
discussable if this is correct/desirable (I don't think
it is), it's clear that the lapic emulation code has
a requirement on firing the hrtimer in the same core
where it was started. This is achieved by making the
hrtimer pinned.
Lastly, note that KVM has code to migrate timers when a
vCPU is scheduled to run in different core. However, this
forced migration may fail. When this happens, we can have
the same problem. If we want 100% correctness, we'll have
to modify apic_timer_fn() to cause a kvm exit when it runs
on a different core than the vCPU. Not sure if this is
possible.
Here's a reproducer for the issue being fixed:
1. Set all cores but core0 to be nohz_full cores
2. Start a guest with a single vCPU
3. Trace apic_timer_fn() and kvm_inject_apic_timer_irqs()
You'll see that apic_timer_fn() will run in core0 while
kvm_inject_apic_timer_irqs() runs in a different core. If
you get both on core0, try running a program that takes 100%
of the CPU and pin it to core0 to force the vCPU out.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
commit 1e133ab296 ("s390/mm: split arch/s390/mm/pgtable.c") dropped
some changes from commit a3a92c31bf ("KVM: s390: fix mismatch
between user and in-kernel guest limit") - this breaks KVM for some
memory sizes (kvm-s390: failed to commit memory region) like
exactly 2GB.
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull MIPS fixes from Ralf Baechle:
"This is the first round of MIPS fixes for 4.6:
- Fix spelling mistakes all over arch/mips
- Provide __bswapsi2 so XZ kernel compression will build with older GCC
- ATH79 clock fixes.
- Fix clock-rated copy-paste erros in ATH79 DTS.
- Fix gisb-arb compatible string for 7435 BMIPS
- Enable NAND and UBIFS support in CI20.
- Fix BUG() assertion caused by inapropriate smp_processor_id() use.
- Fix exception handling issues for the sake of debuggers
- Fix the last remaining instance of irq_to_gpio in the db1xxx_ss PCMCIA code
- Fix MSA unaligned load failures
- Panic if kernel is configured for a not TLB-supported page size
- Bail out on unsupported relocs in modules.
- Partial fix for Qemu breakage after recent IPI rewrite
- Wire up the preadv2 and pwrite2 syscalls
- Fix the ar724x clock calculation"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: traps.c: Verify the ISA for microMIPS RDHWR emulation
MIPS: BMIPS: Fix gisb-arb compatible string for 7435
MIPS: Bail on unsupported module relocs
MIPS: dts: qca: ar9132_tl_wr1043nd_v1.dts: use "ref" for reference clock name
MIPS: ath79: Fix the ar913x reference clock rate
MIPS: ath79: Fix the ar724x clock calculation
dt-bindings: clock: qca,ath79-pll: fix copy-paste typos
MIPS: traps: Correct the SIGTRAP debug ABI in `do_watch' and `do_trap_or_bp'
FIRMWARE: Broadcom: Fix grammar of warning messages in bcm47xx_sprom.c.
MIPS: ci20: Enable NAND and UBIFS support in defconfig.
MIPS: Fix misspellings in comments.
MIPS: tlb-r4k: panic if the MMU doesn't support PAGE_SIZE
MIPS: zboot: Remove copied source files on clean
MIPS: zboot: Fix the build with XZ compression on older GCC versions
MIPS: Wire up preadv2 and pwrite2 syscalls.
MIPS: cpu_name_string: Use raw_smp_processor_id().
pcmcia: db1xxx_ss: fix last irq_to_gpio user
MIPS: Fix MSA ld unaligned failure cases
MIPS: Fix broken malta qemu
- Safely migrate event channels between CPUs.
- Fix CPU hotplug.
- Maintainer changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXAkQtAAoJEFxbo/MsZsTRpAoH/R0mVySTK3RloxRo4SPDWs//
3EIgDFBCde/JfDmhJw7OTLC6oHExq/ObBunV4I6HSStDYjZfHnMXTe7uiRo6oOUt
ql8/k1P4NM202L2qkjZU89ObPwOMbx50NiHtVG3JAIydZc/jgn4/brow9ZymDAUd
lp85Oj0d66uM5iIY9YVa5nY/calt5W0rr9EoV93HSf6GFefNJKXJ5u3KW8IgMyIl
I4/y8GraQLAcXBcmrOny51nlIxsiv1wTssJfExH49/8In3JH3SlbZDGuEiIovPUC
jJ96Tr/oOhFyPZIM3J7pFYpvn4en84V07zbaWcEUmVf8capv3pjwJNg2Xx64FdI=
=bSO5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.6-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from David Vrabel:
"Regression and bug fixes for 4.6-rc2:
- safely migrate event channels between CPUs
- fix CPU hotplug
- maintainer changes"
* tag 'for-linus-4.6-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: xen: Konrad to step down and Juergen to pick up
xen/events: Mask a moving irq
Xen on ARM and ARM64: update MAINTAINERS info
xen/x86: Call cpu_startup_entry(CPUHP_AP_ONLINE_IDLE) from xen_play_dead()
xen/apic: Provide Xen-specific version of cpu_present_to_apicid APIC op
Merge PAGE_CACHE_SIZE removal patches from Kirill Shutemov:
"PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
Let's stop pretending that pages in page cache are special. They are
not.
The first patch with most changes has been done with coccinelle. The
second is manual fixups on top.
The third patch removes macros definition"
[ I was planning to apply this just before rc2, but then I spaced out,
so here it is right _after_ rc2 instead.
As Kirill suggested as a possibility, I could have decided to only
merge the first two patches, and leave the old interfaces for
compatibility, but I'd rather get it all done and any out-of-tree
modules and patches can trivially do the converstion while still also
working with older kernels, so there is little reason to try to
maintain the redundant legacy model. - Linus ]
* PAGE_CACHE_SIZE-removal:
mm: drop PAGE_CACHE_* and page_cache_{get,release} definition
mm, fs: remove remaining PAGE_CACHE_* and page_cache_{get,release} usage
mm, fs: get rid of PAGE_CACHE_* and page_cache_{get,release} macros
Mostly direct substitution with occasional adjustment or removing
outdated comments.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure it's the microMIPS rather than MIPS16 ISA before emulating
microMIPS RDHWR. Mostly needed as an optimisation for configurations
where `cpu_has_mmips' is hardcoded to 0 and also a good measure in case
we add further microMIPS instructions to emulate in the future, as the
corresponding MIPS16 encoding is ADDIUSP, not supposed to trap.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12282/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull x86 fixes from Thomas Gleixner:
"This lot contains:
- Some fixups for the fallout of the topology consolidation which
unearthed AMD/Intel inconsistencies
- Documentation for the x86 topology management
- Support for AMD advanced power management bits
- Two simple cleanups removing duplicated code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add advanced power management bits
x86/thread_info: Merge two !__ASSEMBLY__ sections
x86/cpufreq: Remove duplicated TDP MSR macro definitions
x86/Documentation: Start documenting x86 topology
x86/cpu: Get rid of compute_unit_id
perf/x86/amd: Cleanup Fam10h NB event constraints
x86/topology: Fix AMD core count
When an unsupported reloc is encountered in a module, we currently
blindly branch to whatever would be at its entry in the reloc handler
function pointer arrays. This may be NULL, or if the unsupported reloc
has a type greater than that of the supported reloc with the highest
type then we'll dereference some value after the function pointer array
& branch to that. The result is at best a kernel oops.
Fix this by checking that the reloc type has an entry in the function
pointer array (ie. is less than the number of items in the array) and
that the handler is non-NULL, returning an error code to fail the module
load if no handler is found.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12432/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current ath79 clock.c code does not read reference clock and
pll setup from devicetree. The ar724x_clocks_init() function
recreates the clocks from scratch so devicetree clock
information is dropped. After adding the code which picked up
reference clock from devicetree I have found
that kernel does not boot anymore. The SPI and UART drivers
can't get clk; here are the bootlog error messages:
of_serial: probe of 18020000.uart failed with error -22
ath79-spi: probe of 1f000000.spi failed with error -22
The problem is that clock code assumes that reference clock
name is "ref" but current dts-file uses another name: "oscillator".
This patch fixes the problem by changing external oscillator
dt node name to "ref".
Please note that there is an alternative solution for the problem:
> --- a/arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts
> +++ b/arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts
> @@ -16,6 +16,7 @@
>
> extosc: oscillator {
> compatible = "fixed-clock";
> + clock-output-names = "ref";
> #clock-cells = <0>;
> clock-frequency = <40000000>;
> };
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The reference clock on ar913x is at 40MHz and not 5MHz. The current
implementation use the wrong reference rate because it doesn't take
the PLL divider in account. But if we fix the code to use the divider
it becomes identical with the implementation for ar724x, so just drop
the broken ar913x implementation.
Signed-off-by: Alban Bedel <albeu@free.fr>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12871/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
According to the AR7242 datasheet section 2.8, AR724X CPUs use a 40MHz
input clock as the REF_CLK instead of 5MHz.
The correct CPU PLL calculation procedure is as follows:
CPU_PLL = (FB * REF_CLK) / REF_DIV / 2.
This patch is compatible with the current calculation procedure with
default FB and REF_DIV values.
Tested on AR7240, AR7241 and AR7242.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Alban Bedel <albeu@free.fr> (Fixed the commit log message)
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12870/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Follow our own rules set in <asm/siginfo.h> for SIGTRAP signals issued
from `do_watch' and `do_trap_or_bp' by setting the signal code to
TRAP_HWBKPT and TRAP_BRKPT respectively, for Watch exceptions and for
those Breakpoint exceptions whose originating BREAK instruction's code
does not have a special meaning. Keep Trap exceptions unaffected as
these are not debug events.
No existing user software is expected to examine signal codes for these
signals as SI_KERNEL has been always used here. This change makes the
MIPS port more like other Linux ports, which reduces the complexity and
provides for performance improvement in GDB.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Luis Machado <lgustavo@codesourcery.com>
Cc: linux-mips@linux-mips.org
Cc: gdb@sourceware.org
Patchwork: https://patchwork.linux-mips.org/patch/12758/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After writing the appropriate mask to the cop0 PageMask register, read
the register back & check it matches what we want. If it doesn't then
the MMU does not support the page size the kernel is configured for and
we're better off bailing than continuing to do odd things with TLB
exceptions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10691/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The copied source files must be added to the extra-y list to have them
removed on clean.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12233/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some older GCC version (at least 4.6) emits calls to __bswapsi2() when
building the XZ decompressor. The link of the compressed image then
fails with the following error:
arch/mips/boot/compressed/decompress.o: In function '__fswab32':
include/uapi/linux/swab.h:60: undefined reference to '__bswapsi2'
Add bswapsi.o to the link to fix the build with these versions.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12232/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Just one fix for a nasty boot failure on some systems based on
Intel Skylake that shipped with broken firmware where enabling
hardware-coordinated P-states management (HWP) causes a faulty
interrupt handler in SMM to be invoked and crash the system
(Srinivas Pandruvada).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=GJ34
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fix from Rafael J. Wysocki:
"Just one fix for a nasty boot failure on some systems based on Intel
Skylake that shipped with broken firmware where enabling
hardware-coordinated P-states management (HWP) causes a faulty
interrupt handler in SMM to be invoked and crash the system (Srinivas
Pandruvada)"
* tag 'pm+acpi-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / processor: Request native thermal interrupt handling via _OSC
Merge fixes from Andrew Morton:
"11 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
.mailmap: add Christophe Ricard
Make CONFIG_FHANDLE default y
mm/page_isolation.c: fix the function comments
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
mm/page_isolation: fix tracepoint to mirror check function behavior
mm/rmap: batched invalidations should use existing api
x86/mm: TLB_REMOTE_SEND_IPI should count pages
mm: fix invalid node in alloc_migrate_target()
include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
mm, kasan: fix compilation for CONFIG_SLAB
MAINTAINERS: orangefs mailing list is subscribers-only
Masahiro Yamada reports that we can fail to set the FW bit in the
auxiliary control register, which enables broadcasting the cache
maintanence operations. This occurs because we only check that the
SMP/nAMP bit is set, rather than checking whether all the bits we
want to be set are set.
Rearrange the code to ensure that all desired bits are set, and only
update the register if we discover some required bits are not set.
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Fix oops when patching in alternative sequences on big-endian CPUs
- Reconcile asm/perf_event.h after merge window fallout with KVM ARM
- Defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJW/jkCAAoJELescNyEwWM0xyAH+wdmjlc5WqtgjF68AYRgbWk/
5GufYlxeMvST7eyT65dZKAyDpJpOBnTXMB7u8KkoGgSEmrdDV0bAjn5CJX41rfxf
dlc9QDisuCAmxuIkQYGK2IJhnk69ehKhqw0w8dstVW2CSOBYtHnSSNtV8WyrKj+D
QEM2Z86HCqM8BaSYhxv8Cte8W5fBegCqciJAVQoihAwioiuZ3cgsrLrT2QHaDhin
gfCTNk/snHG3PAvuy+Kx1PICMH+ur4Enk8bft8xO6HzqSSDsWv/TD35VzcX5pY9V
PRlC4D5TCEzwQQmFHpUj4PeQytIQge/Y3Ux/OUk1caq0Yei13RhOhR9q2+gTwKI=
=gJNY
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- fix oops when patching in alternative sequences on big-endian CPUs
- reconcile asm/perf_event.h after merge window fallout with KVM ARM
- defconfig updates
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: updates for 4.6
arm64: perf: Move PMU register related defines to asm/perf_event.h
arm64: opcodes.h: Add arm big-endian config options before including arm header
Ard Biesheuvel