This allows to monitor carrier on/off transitions and detect link
flapping issues:
- new /sys/class/net/X/carrier_changes
- new rtnetlink IFLA_CARRIER_CHANGES (getlink)
Tested:
- grep . /sys/class/net/*/carrier_changes
+ ip link set dev X down/up
+ plug/unplug cable
- updated iproute2: prints IFLA_CARRIER_CHANGES
- iproute2 20121211-2 (debian): unchanged behavior
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently pch_gbe, cpts, and ixp4xx_eth drivers that open-code
and reimplement a BPF classifier for the PTP protocol. Since all of them
effectively do the very same thing and load the very same PTP/BPF filter,
we can just consolidate that code by introducing ptp_classify_raw() in
the time-stamping core framework which can be used in drivers.
As drivers get initialized after bootstrapping the core networking
subsystem, they can make use of ptp_insns wrapped through
ptp_classify_raw(), which allows to simplify and remove PTP classifier
setup code in drivers.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch migrates an open-coded sk_run_filter() implementation with
proper use of the BPF API, that is, sk_unattached_filter_create(). This
migration is needed, as we will be internally transforming the filter
to a different representation, and therefore needs to be decoupled.
It is okay to do so as skb_timestamping_init() is called during
initialization of the network stack in core initcall via sock_init().
This would effectively also allow for PTP filters to be jit compiled if
bpf_jit_enable is set.
For better readability, there are also some newlines introduced, also
ptp_classify.h is only in kernel space.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch basically does two things, i) removes the extern keyword
from the include/linux/filter.h file to be more consistent with the
rest of Joe's changes, and ii) moves filter accounting into the filter
core framework.
Filter accounting mainly done through sk_filter_{un,}charge() take
care of the case when sockets are being cloned through sk_clone_lock()
so that removal of the filter on one socket won't result in eviction
as it's still referenced by the other.
These functions actually belong to net/core/filter.c and not
include/net/sock.h as we want to keep all that in a central place.
It's also not in fast-path so uninlining them is fine and even allows
us to get rd of sk_filter_release_rcu()'s EXPORT_SYMBOL and a forward
declaration.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc927780 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a jited flag into sk_filter struct in order to indicate
whether a filter is currently jited or not. The size of sk_filter is
not being expanded as the 32 bit 'len' member allows upper bits to be
reused since a filter can currently only grow as large as BPF_MAXINSNS.
Therefore, there's enough room also for other in future needed flags to
reuse 'len' field if necessary. The jited flag also allows for having
alternative interpreter functions running as currently, we can only
detect jit compiled filters by testing fp->bpf_func to not equal the
address of sk_run_filter().
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop taking the transmit lock when a network device has specified
NETIF_F_LLTX.
If no locks needed to trasnmit a packet this is the ideal scenario for
netpoll as all packets can be trasnmitted immediately.
Even if some locks are needed in ndo_start_xmit skipping any unnecessary
serialization is desirable for netpoll as it makes it more likely a
debugging packet may be trasnmitted immediately instead of being
deferred until later.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the assumption that the skbs that make it to
netpoll_send_skb_on_dev are allocated with find_skb, such that
skb->users == 1 and nothing is attached that would prevent the skbs from
being freed from hard irq context.
Remove this assumption by replacing __kfree_skb on error paths with
dev_kfree_skb_irq (in hard irq context) and kfree_skb (in process
context).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll_rx_enable and netpoll_rx_disable functions have always
controlled polling the network drivers transmit and receive queues.
Rename them to netpoll_poll_enable and netpoll_poll_disable to make
their functionality clear.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today netpoll_rx_enable and netpoll_rx_disable are called from
dev_close and and __dev_close, and not from dev_close_many.
Move the calls into __dev_close_many so that we have a single call
site to maintain, and so that dev_close_many gains this protection as
well. Which importantly makes batched network device deletes safe.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the code that needs to surround ndo_start_xmit
from netpoll_send_skb_on_dev into netpoll_start_xmit.
It is an unfortunate fact that as the netpoll code has been maintained
the primary call site ndo_start_xmit learned how to handle vlans
and timestamps but the second call of ndo_start_xmit in queue_process
did not.
With the introduction of netpoll_start_xmit this associated logic now
happens at both call sites of ndo_start_xmit and should make it easy
for that to continue into the future.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfp parameter was added in:
commit 47be03a28c
Author: Amerigo Wang <amwang@redhat.com>
Date: Fri Aug 10 01:24:37 2012 +0000
netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the gfp parameter was removed in:
commit c4cdef9b71
Author: dingtianhong <dingtianhong@huawei.com>
Date: Tue Jul 23 15:25:27 2013 +0800
bonding: don't call slave_xxx_netpoll under spinlocks
The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.
bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing else that calls __netpoll_setup or ndo_netpoll_setup
requires a gfp paramter, so remove the gfp parameter from both
of these functions making the code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb. However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers. That may not
always be the case. If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.
A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated. This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dropping packets in __dev_queue_xmit() when transmit queue
is stopped (NIC TX ring buffer full or BQL limit reached) currently
outputs a syslog message.
It would be better to get a precise count of such events available in
netdevice stats so that monitoring tools can have a clue.
This extends the work done in caf586e5f2
("net: add a core netdev->rx_dropped counter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_zerocopy can copy elements of the frags array between skbs, but it doesn't
orphan them. Also, it doesn't handle errors, so this patch takes care of that
as well, and modify the callers accordingly. skb_tx_error() is also added to
the callers so they will signal the failed delivery towards the creator of the
skb.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)
The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.
And in the case of the NULL pointer, there is no structure to initialize.
So, rcu_assign_pointer(p, NULL) can be safely converted to RCU_INIT_POINTER(p, NULL)
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet hash can be considered a property of the packet, not just
on RX path.
This patch changes name of rxhash and l4_rxhash skbuff fields to be
hash and l4_hash respectively. This includes changing uses of the
field in the code which don't call the access functions.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Neighbor Solicitation is ipv6 protocol, so we should check
skb->protocol with ETH_P_IPV6
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Cc: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ff661c38c ("net: rtnetlink notify events for FDB NTF_SELF adds and
deletes") reuses the function nlmsg_populate_fdb_fill() to notify fdb events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.
Libraries like libnl will wait forever for NLMSG_DONE.
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the code in net/core/flow.c by using this latter form of callback
registration.
Cc: Li RongQing <roy.qing.li@gmail.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cftype->write_string() just passes on the writeable buffer from kernfs
and there's no reason to add const restriction on the buffer. The
only thing const achieves is unnecessarily complicating parsing of the
buffer. Drop const from @buffer.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
The netpoll packet receive code only becomes active if the netpoll
rx_skb_hook is implemented, and there is not a single implementation
of the netpoll rx_skb_hook in the kernel.
All of the out of tree implementations I have found all call
netpoll_poll which was removed from the kernel in 2011, so this
change should not add any additional breakage.
There are problems with the netpoll packet receive code. __netpoll_rx
does not call dev_kfree_skb_irq or dev_kfree_skb_any in hard irq
context. netpoll_neigh_reply leaks every skb it receives. Reception
of packets does not work successfully on stacked devices (aka bonding,
team, bridge, and vlans).
Given that the netpoll packet receive code is buggy, there are no
out of tree users that will be merged soon, and the code has
not been used for in tree for a decade let's just remove it.
Reverting this commit can server as a starting point for anyone
who wants to resurrect netpoll packet reception support.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make rx_skb_hook, and rx in struct netpoll depend on
CONFIG_NETPOLL_TRAP Make rx_lock, rx_np, and neigh_tx in struct
netpoll_info depend on CONFIG_NETPOLL_TRAP
Make the functions netpoll_rx_on, netpoll_rx, and netpoll_receive_skb
no-ops when CONFIG_NETPOLL_TRAP is not set.
Only build netpoll_neigh_reply, checksum_udp service_neigh_queue,
pkt_is_ns, and __netpoll_rx when CONFIG_NETPOLL_TRAP is defined.
Add helper functions netpoll_trap_setup, netpoll_trap_setup_info,
netpoll_trap_cleanup, and netpoll_trap_cleanup_info that initialize
and cleanup the struct netpoll and struct netpoll_info receive
specific fields when CONFIG_NETPOLL_TRAP is enabled and do nothing
otherwise.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bond slave device neigh_tx handling into service_neigh_queue.
In connection with neigh_tx processing remove unnecessary tests of
a NULL netpoll_info. As the netpoll_poll_dev has already used
and thus verified the existince of the netpoll_info.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we no longer need to receive packets to safely drain the
network drivers receive queue move netpoll_trap and netpoll_set_trap
under CONFIG_NETPOLL_TRAP
Making netpoll_trap and netpoll_set_trap noop inline functions
when CONFIG_NETPOLL_TRAP is not set.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the strategy of netpoll from dropping all packets received
during netpoll_poll_dev to calling napi poll with a budget of 0
(to avoid processing drivers rx queue), and to ignore packets received
with netif_rx (those will safely be placed on the backlog queue).
All of the netpoll supporting drivers have been reviewed to ensure
either thay use netif_rx or that a budget of 0 is supported by their
napi poll routine and that a budget of 0 will not process the drivers
rx queues.
Not dropping packets makes NETPOLL_RX_DROP unnecesary so it is removed.
npinfo->rx_flags is removed as rx_flags with just the NETPOLL_RX_ENABLED
flag becomes just a redundant mirror of list_empty(&npinfo->rx_np).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper netpoll_rx_processing that reports when netpoll has
receive side processing to perform.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is already a warning for this case in the normal netpoll path,
but put a copy here in case how netpoll calls the poll functions
causes a differenet result.
netpoll will shortly call the napi poll routine with a budget 0 to
avoid any rx packets being processed. As nothing does that today
we may encounter drivers that have problems so a netpoll specific
warning seems desirable.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In poll_napi loop through all of the napi handlers even when the
budget falls to 0 to ensure that we process all of the tx_queues, and
so that we continue to call into drivers when our initial budget is 0.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves the control logic to the top level in netpoll_poll_dev
instead of having it dispersed throughout netpoll_poll_dev,
poll_napi and poll_one_napi.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today netpoll depends on setting NETPOLL_RX_DROP before networking
drivers receive packets in interrupt context so that the packets can
be dropped. Move this setting into netpoll_poll_dev from
poll_one_napi so that if ndo_poll_controller happens to receive
packets we will drop the packets on the floor instead of letting the
packets bounce through the networking stack and potentially cause problems.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
consolidate duplicate code is skb_checksum_setup() helpers
Realizing that the skb_maybe_pull_tail() calls in the IP-protocol
specific portions of both helpers are terminal ones (i.e. no further
pulls are expected), their maximum size to be pulled can be made match
their minimal size needed, thus making the code identical and hence
possible to be moved into another helper.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We leak an active timer, the hotcpu notifier and all allocated
resources when we exit a namespace. Fix this by introducing a
flow_cache_fini() function where we release the resources before
we exit.
Fixes: ca925cf153 ("flowcache: Make flow cache name space aware")
Reported-by: Jakub Kicinski <moorray3@wp.pl>
Tested-by: Jakub Kicinski <moorray3@wp.pl>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_segment copies frags around, so we need
to copy them carefully to avoid accessing
user memory after reporting completion to userspace
through a callback.
skb_segment doesn't normally happen on datapath:
TSO needs to be disabled - so disabling zero copy
in this case does not look like a big deal.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
fskb is unrelated to frag: it's coming from
frag_list. Rename it list_skb to avoid confusion.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rename local variable to make it easier to tell at a glance that we are
dealing with a head skb.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_frag can in fact point at either skb
or fskb so rename it generally "frag".
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not legal to create multiple kmem_cache having the same name.
flowcache can use a single kmem_cache, no need for a per netns
one.
Fixes: ca925cf153 ("flowcache: Make flow cache name space aware")
Reported-by: Jakub Kicinski <moorray3@wp.pl>
Tested-by: Jakub Kicinski <moorray3@wp.pl>
Tested-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the neigh table's entries is less than gc_thresh1, the function
will return directly, and the reachabletime will not be recompute,
so the reachabletime can be guessed.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because those following if conditions will not be matched.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iproute2 arpd seems to expect this as there's code and comments
to handle netlink probes with NUD_PROBE set. It is used to flush
the arpd cached mappings.
opennhrp instead turns off unicast probes (so it can handle all
neighbour discovery). Without this change it will not see NUD_PROBE
probes and cannot reconfirm the mapping. Thus currently neigh entry
will just fail and can cause few packets dropped until broadcast
discovery is restarted.
Earlier discussion on the subject:
http://marc.info/?t=139305877100001&r=1&w=2
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sysfs file to enable user space to query the device
port number used by a netdevice instance. This is needed for
devices that have multiple ports on the same PCI function.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation misses a few of the supported flags. Fix this. Also
respect the dependency to CONFIG_XFRM for the IPSEC flag.
Cc: Fan Du <fan.du@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'out' label is just a relict from previous times as pgctrl_write()
had multiple error paths. Get rid of it and simply return right away
on errors.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a privileged user writes an empty string to /proc/net/pktgen/pgctrl
the code for stripping the (then non-existent) '\n' actually writes the
zero byte at index -1 of data[]. The then still uninitialized array will
very likely fail the command matching tests and the pr_warning() at the
end will therefore leak stack bytes to the kernel log.
Fix those issues by simply ensuring we're passed a non-empty string as
the user API apparently expects a trailing '\n' for all commands.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
1) Introduce skb_to_sgvec_nomark function to add further data to the sg list
without calling sg_unmark_end first. Needed to add extended sequence
number informations. From Fan Du.
2) Add IPsec extended sequence numbers support to the Authentication Header
protocol for ipv4 and ipv6. From Fan Du.
3) Make the IPsec flowcache namespace aware, from Fan Du.
4) Avoid creating temporary SA for every packet when no key manager is
registered. From Horia Geanta.
5) Support filtering of SA dumps to show only the SAs that match a
given filter. From Nicolas Dichtel.
6) Remove caching of xfrm_policy_sk_bundles. The cached socket policy bundles
are never used, instead we create a new cache entry whenever xfrm_lookup()
is called on a socket policy. Most protocols cache the used routes to the
socket, so this caching is not needed.
7) Fix a forgotten SADB_X_EXT_FILTER length check in pfkey, from Nicolas
Dichtel.
8) Cleanup error handling of xfrm_state_clone.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The name __smp_call_function_single() doesn't tell much about the
properties of this function, especially when compared to
smp_call_function_single().
The comments above the implementation are also misleading. The main
point of this function is actually not to be able to embed the csd
in an object. This is actually a requirement that result from the
purpose of this function which is to raise an IPI asynchronously.
As such it can be called with interrupts disabled. And this feature
comes at the cost of the caller who then needs to serialize the
IPIs on this csd.
Lets rename the function and enhance the comments so that they reflect
these properties.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The main point of calling __smp_call_function_single() is to send
an IPI in a pure asynchronous way. By embedding a csd in an object,
a caller can send the IPI without waiting for a previous one to complete
as is required by smp_call_function_single() for example. As such,
sending this kind of IPI can be safe even when irqs are disabled.
This flexibility comes at the expense of the caller who then needs to
synchronize the csd lifecycle by himself and make sure that IPIs on a
single csd are serialized.
This is how __smp_call_function_single() works when wait = 0 and this
usecase is relevant.
Now there don't seem to be any usecase with wait = 1 that can't be
covered by smp_call_function_single() instead, which is safer. Lets look
at the two possible scenario:
1) The user calls __smp_call_function_single(wait = 1) on a csd embedded
in an object. It looks like a nice and convenient pattern at the first
sight because we can then retrieve the object from the IPI handler easily.
But actually it is a waste of memory space in the object since the csd
can be allocated from the stack by smp_call_function_single(wait = 1)
and the object can be passed an the IPI argument.
Besides that, embedding the csd in an object is more error prone
because the caller must take care of the serialization of the IPIs
for this csd.
2) The user calls __smp_call_function_single(wait = 1) on a csd that
is allocated on the stack. It's ok but smp_call_function_single()
can do it as well and it already takes care of the allocation on the
stack. Again it's more simple and less error prone.
Therefore, using the underscore prepend API version with wait = 1
is a bad pattern and a sign that the caller can do safer and more
simple.
There was a single user of that which has just been converted.
So lets remove this option to discourage further users.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fixes bug introduced by:
commit 1d4c8c2984
"neigh: restore old behaviour of default parms values"
The thing is that in neigh_sysctl_register, extra1 and extra2 which were
previously set for NEIGH_VAR_GC_* are overwritten. That leads to
nonsense int limits for gc_* variables. So fix this by not touching
extra* fields for gc_* variables.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
* Fix nf_trace in nftables if XT_TRACE=n, from Florian Westphal.
* Don't use the fast payload operation in nf_tables if the length is
not power of 2 or it is not aligned, from Nikolay Aleksandrov.
* Fix missing break statement the inet flavour of nft_reject, which
results in evaluating IPv4 packets with the IPv6 evaluation routine,
from Patrick McHardy.
* Fix wrong kconfig symbol in nft_meta to match the routing realm,
from Paul Bolle.
* Allocate the NAT null binding when creating new conntracks via
ctnetlink to avoid that several packets race at initializing the
the conntrack NAT extension, original patch from Florian Westphal,
revisited version from me.
* Fix DNAT handling in the snmp NAT helper, the same handling was being
done for SNAT and DNAT and 2.4 already contains that fix, from
Francois-Xavier Le Bail.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The only place this is used outside rtnetlink.c is veth. So provide
wrapper function for this usage.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using nftables with CONFIG_NETFILTER_XT_TARGET_TRACE=n, we get
lots of "TRACE: filter:output:policy:1 IN=..." warnings as several
places will leave skb->nf_trace uninitialised.
Unlike iptables tracing functionality is not conditional in nftables,
so always copy/zero nf_trace setting when nftables is enabled.
Move this into __nf_copy() helper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In order to allow users to invoke netdev_cap_txqueue, it needs to
be moved into netdevice.h header file. While at it, also add kernel
doc header to document the API.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one inline keyword, and no need for a loop to find
an index into a table.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of my pet coding style peeves is the practice of
adding extra return; at the end of function.
Kill several instances of this in network code.
I suppose some coccinelle wizardy could do this automatically.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be used by upcoming ipv4 forward path change that needs to
determine feature mask using skb->dst->dev instead of skb->dev.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I saw the following BUG when ->newlink() fails in rtnl_newlink():
[ 40.240058] kernel BUG at net/core/dev.c:6438!
this is due to free_netdev() is not supposed to be called before
netdev is completely unregistered, therefore it is not correct
to call free_netdev() here, at least for ops->newlink!=NULL case,
many drivers call it in ->destructor so that rtnl_unlock() will
take care of it, we probably don't need to do anything here.
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If !NULL, @skip_css makes cgroup_taskset_for_each() skip the matching
css. The intention of the interface is to make it easy to skip css's
(cgroup_subsys_states) which already match the migration target;
however, this is entirely unnecessary as migration taskset doesn't
include tasks which are already in the target cgroup. Drop @skip_css
from cgroup_taskset_for_each().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Inserting a entry into flowcache, or flushing flowcache should be based
on per net scope. The reason to do so is flushing operation from fat
netns crammed with flow entries will also making the slim netns with only
a few flow cache entries go away in original implementation.
Since flowcache is tightly coupled with IPsec, so it would be easier to
put flow cache global parameters into xfrm namespace part. And one last
thing needs to do is bumping flow cache genid, and flush flow cache should
also be made in per net style.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
As compared with skb_to_sgvec, skb_to_sgvec_nomark only map skb to given sglist
without mark the sg which contain last skb data as the end. So the caller can
mannipulate sg list as will when padding new data after the first call without
calling sg_unmark_end to expend sg list.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
ip rules with iif/oif references do not update:
(detach/attach) across interface renames.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
CC: Willem de Bruijn <willemb@google.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Chris Davis <chrismd@google.com>
CC: Carlo Contavalli <ccontavalli@google.com>
Google-Bug-Id: 12936021
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark functions as static in core/dev.c because they are not used outside
this file.
This eliminates the following warning in core/dev.c:
net/core/dev.c:2806:5: warning: no previous prototype for ‘__dev_queue_xmit’ [-Wmissing-prototypes]
net/core/dev.c:4640:5: warning: no previous prototype for ‘netdev_adjacent_sysfs_add’ [-Wmissing-prototypes]
net/core/dev.c:4650:6: warning: no previous prototype for ‘netdev_adjacent_sysfs_del’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cgroup_subsys is a bit messier than it needs to be.
* The name of a subsys can be different from its internal identifier
defined in cgroup_subsys.h. Most subsystems use the matching name
but three - cpu, memory and perf_event - use different ones.
* cgroup_subsys_id enums are postfixed with _subsys_id and each
cgroup_subsys is postfixed with _subsys. cgroup.h is widely
included throughout various subsystems, it doesn't and shouldn't
have claim on such generic names which don't have any qualifier
indicating that they belong to cgroup.
* cgroup_subsys->subsys_id should always equal the matching
cgroup_subsys_id enum; however, we require each controller to
initialize it and then BUG if they don't match, which is a bit
silly.
This patch cleans up cgroup_subsys names and initialization by doing
the followings.
* cgroup_subsys_id enums are now postfixed with _cgrp_id, and each
cgroup_subsys with _cgrp_subsys.
* With the above, renaming subsys identifiers to match the userland
visible names doesn't cause any naming conflicts. All non-matching
identifiers are renamed to match the official names.
cpu_cgroup -> cpu
mem_cgroup -> memory
perf -> perf_event
* controllers no longer need to initialize ->subsys_id and ->name.
They're generated in cgroup core and set automatically during boot.
* Redundant cgroup_subsys declarations removed.
* While updating BUG_ON()s in cgroup_init_early(), convert them to
WARN()s. BUGging that early during boot is stupid - the kernel
can't print anything, even through serial console and the trap
handler doesn't even link stack frame properly for back-tracing.
This patch doesn't introduce any behavior changes.
v2: Rebased on top of fe1217c4f3 ("net: net_cls: move cgroupfs
classid handling into core").
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Ingo Molnar <mingo@redhat.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Thomas Graf <tgraf@suug.ch>
With module supported dropped from net_prio, no controller is using
cgroup module support. None of actual resource controllers can be
built as a module and we aren't gonna add new controllers which don't
control resources. This patch drops module support from cgroup.
* cgroup_[un]load_subsys() and cgroup_subsys->module removed.
* As there's no point in distinguishing IS_BUILTIN() and IS_MODULE(),
cgroup_subsys.h now uses IS_ENABLED() directly.
* enum cgroup_subsys_id now exactly matches the list of enabled
controllers as ordered in cgroup_subsys.h.
* cgroup_subsys[] is now a contiguously occupied array. Size
specification is no longer necessary and dropped.
* for_each_builtin_subsys() is removed and for_each_subsys() is
updated to not require any locking.
* module ref handling is removed from rebind_subsystems().
* Module related comments dropped.
v2: Rebased on top of fe1217c4f3 ("net: net_cls: move cgroupfs
classid handling into core").
v3: Added {} around the if (need_forkexit_callback) block in
cgroup_post_fork() for readability as suggested by Li.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
net_prio is the only cgroup which is allowed to be built as a module.
The savings from allowing one controller to be built as a module are
tiny especially given that cgroup module support itself adds quite a
bit of complexity.
Given that none of other controllers has much chance of being made a
module and that we're unlikely to add new modular controllers, the
added complexity is simply not justifiable.
As a first step to drop cgroup module support, this patch changes the
config option to bool from tristate and drops module related code from
it.
Also, while an earlier commit fe1217c4f3 ("net: net_cls: move
cgroupfs classid handling into core") dropped module support from
net_cls cgroup, it retained a call to cgroup_load_subsys(), which is
noop for built-in controllers. Drop it along with
init_netclassid_cgroup().
v2: Removed modular version of task_netprioidx() in
include/net/netprio_cgroup.h as suggested by Li Zefan.
v3: Rebased on top of fe1217c4f3 ("net: net_cls: move cgroupfs
classid handling into core"). net_cls cgroup part is mostly
dropped except for removal of init_netclassid_cgroup().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Thomas Graf <tgraf@suug.ch>
sock_alloc_send_pskb() & sk_page_frag_refill()
have a loop trying high order allocations to prepare
skb with low number of fragments as this increases performance.
Problem is that under memory pressure/fragmentation, this can
trigger OOM while the intent was only to try the high order
allocations, then fallback to order-0 allocations.
We had various reports from unexpected regressions.
According to David, setting __GFP_NORETRY should be fine,
as the asynchronous compaction is still enabled, and this
will prevent OOM from kicking as in :
CFSClientEventm invoked oom-killer: gfp_mask=0x42d0, order=3, oom_adj=0,
oom_score_adj=0, oom_score_badness=2 (enabled),memcg_scoring=disabled
CFSClientEventm
Call Trace:
[<ffffffff8043766c>] dump_header+0xe1/0x23e
[<ffffffff80437a02>] oom_kill_process+0x6a/0x323
[<ffffffff80438443>] out_of_memory+0x4b3/0x50d
[<ffffffff8043a4a6>] __alloc_pages_may_oom+0xa2/0xc7
[<ffffffff80236f42>] __alloc_pages_nodemask+0x1002/0x17f0
[<ffffffff8024bd23>] alloc_pages_current+0x103/0x2b0
[<ffffffff8028567f>] sk_page_frag_refill+0x8f/0x160
[<ffffffff80295fa0>] tcp_sendmsg+0x560/0xee0
[<ffffffff802a5037>] inet_sendmsg+0x67/0x100
[<ffffffff80283c9c>] __sock_sendmsg_nosec+0x6c/0x90
[<ffffffff80283e85>] sock_sendmsg+0xc5/0xf0
[<ffffffff802847b6>] __sys_sendmsg+0x136/0x430
[<ffffffff80284ec8>] sys_sendmsg+0x88/0x110
[<ffffffff80711472>] system_call_fastpath+0x16/0x1b
Out of Memory: Kill process 2856 (bash) score 9999 or sacrifice child
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, to make netconsole start over IPv6, the source address
needs to be specified. Without a source address, netpoll_parse_options
assumes we're setting up over IPv4 and the destination IPv6 address is
rejected.
Check if the IP version has been forced by a source address before
checking for a version mismatch when parsing the destination address.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed following Warning while executing "make htmldocs".
Warning(/net/core/skbuff.c:2164): No description found for parameter 'from'
Warning(/net/core/skbuff.c:2164): Excess function parameter 'source'
description in 'skb_zerocopy'
Replace "@source" with "@from" fixed the warning.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves part of Eric Dumazets skb_gso_seglen helper from tbf sched to
skbuff core so it may be reused by upcoming ip forwarding path patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
This check is not needed because the same check is done before
fill_slave_info is used in rtnl_link_slave_info_fill.
Also, by removing this check, kernel will fillup IFLA_INFO_SLAVE_KIND
even for slaves of masters which does not implement fill_slave_info.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have multiple devices attempting to sync the same address
to a single destination, each device should be permitted to sync
it once. To accomplish this, pass the 'sync_cnt' of the source
address when adding the addresss to the lower device. 'sync_cnt'
tracks how many time a given address has been succefully synced.
This way, we know that if the 'sync_cnt' passed in is 0, we should
sync this address.
Also, turn 'synced' member back into the counter as was originally
done in
commit 4543fbefe6.
net: count hw_addr syncs so that unsync works properly.
It tracks how many time a given address has been added via a
'sync' operation. For every successfull 'sync' the counter is
incremented, and for ever 'unsync', the counter is decremented.
This makes sure that the address will be properly removed from
the the lower device when all the upper devices have removed it.
Reported-by: Andrey Dmitrov <andrey.dmitrov@oktetlabs.ru>
CC: Andrey Dmitrov <andrey.dmitrov@oktetlabs.ru>
CC: Alexandra N. Kossovsky <Alexandra.Kossovsky@oktetlabs.ru>
CC: Konstantin Ushakov <Konstantin.Ushakov@oktetlabs.ru>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull fuse update from Miklos Szeredi:
"This contains a fix for a potential use-after-module-unload bug
noticed by Al and caching improvements for read-only fuse filesystems
by Andrew Gallagher"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: support clients that don't implement 'open'
fuse: don't invalidate attrs when not using atime
fuse: fix SetPageUptodate() condition in STORE
fuse: fix pipe_buf_operations
Recent patch
bonding: add netlink attributes to slave link dev (1d3ee88ae0)
Introduced yet another device specific way to access slave information
over rtnetlink. There is one already there for bridge.
This patch introduces generic way to do this, for getting and setting
info as well by extending link_ops. Later on, this new interface will
be used for bridge ports as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Workqueue used in neighbour layer have no real dependency of scheduling these on
the cpu which scheduled them.
On a idle system, it is observed that an idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.
This patch replaces normal workqueues with power efficient versions. This
doesn't change existing behavior of code unless CONFIG_WQ_POWER_EFFICIENT is
enabled.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
Having this struct in module memory could Oops when if the module is
unloaded while the buffer still persists in a pipe.
Since sock_pipe_buf_ops is essentially the same as fuse_dev_pipe_buf_steal
merge them into nosteal_pipe_buf_ops (this is the same as
default_pipe_buf_ops except stealing the page from the buffer is not
allowed).
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
Use ether_addr_copy instead of memcpy(a, b, ETH_ALEN) to
save some cycles on arm and powerpc.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ether_addr_copy instead of memcpy(a, b, ETH_ALEN) to
save some cycles on arm and powerpc.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the gro_find_receive/complete_by_type helpers to they can be invoked
by the gro callbacks of encapsulation protocols such as vxlan.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add GRO handlers for protocols that do UDP encapsulation, with the intent of
being able to coalesce packets which encapsulate packets belonging to
the same TCP session.
For GRO purposes, the destination UDP port takes the role of the ether type
field in the ethernet header or the next protocol in the IP header.
The UDP GRO handler will only attempt to coalesce packets whose destination
port is registered to have gro handler.
Use a mark on the skb GRO CB data to disallow (flush) running the udp gro receive
code twice on a packet. This solves the problem of udp encapsulated packets whose
inner VM packet is udp and happen to carry a port which has registered offloads.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup updates from Tejun Heo:
"The bulk of changes are cleanups and preparations for the upcoming
kernfs conversion.
- cgroup_event mechanism which is and will be used only by memcg is
moved to memcg.
- pidlist handling is updated so that it can be served by seq_file.
Also, the list is not sorted if sane_behavior. cgroup
documentation explicitly states that the file is not sorted but it
has been for quite some time.
- All cgroup file handling now happens on top of seq_file. This is
to prepare for kernfs conversion. In addition, all operations are
restructured so that they map 1-1 to kernfs operations.
- Other cleanups and low-pri fixes"
* 'for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (40 commits)
cgroup: trivial style updates
cgroup: remove stray references to css_id
doc: cgroups: Fix typo in doc/cgroups
cgroup: fix fail path in cgroup_load_subsys()
cgroup: fix missing unlock on error in cgroup_load_subsys()
cgroup: remove for_each_root_subsys()
cgroup: implement for_each_css()
cgroup: factor out cgroup_subsys_state creation into create_css()
cgroup: combine css handling loops in cgroup_create()
cgroup: reorder operations in cgroup_create()
cgroup: make for_each_subsys() useable under cgroup_root_mutex
cgroup: css iterations and css_from_dir() are safe under cgroup_mutex
cgroup: unify pidlist and other file handling
cgroup: replace cftype->read_seq_string() with cftype->seq_show()
cgroup: attach cgroup_open_file to all cgroup files
cgroup: generalize cgroup_pidlist_open_file
cgroup: unify read path so that seq_file is always used
cgroup: unify cgroup_write_X64() and cgroup_write_string()
cgroup: remove cftype->read(), ->read_map() and ->write()
hugetlb_cgroup: convert away from cftype->read()
...
softnet_data is already set to 0, no need to use memset or initialize
specific fields to 0 or NULL afterwards.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I create a new namespace with 'ip netns add net0', or add/remove
new links in a namespace with 'ip link add/delete type veth', rx/tx
queues events can be got in all namespaces. That is because rx/tx queue
ktypes do not have namespace support, and their kobj parents are setted to
NULL. This patch is to fix it.
Reported-by: Libo Chen <chenlibo@huawei.com>
Signed-off-by: Libo Chen <chenlibo@huawei.com>
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To silent "make htmldocs" warning.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For user space packet capturing libraries such as libpcap, there's
currently only one way to check which BPF extensions are supported
by the kernel, that is, commit aa1113d9f8 ("net: filter: return
-EINVAL if BPF_S_ANC* operation is not supported"). For querying all
extensions at once this might be rather inconvenient.
Therefore, this patch introduces a new option which can be used as
an argument for getsockopt(), and allows one to obtain information
about which BPF extensions are supported by the current kernel.
As David Miller suggests, we do not need to define any bits right
now and status quo can just return 0 in order to state that this
versions supports SKF_AD_PROTOCOL up to SKF_AD_PAY_OFFSET. Later
additions to BPF extensions need to add their bits to the
bpf_tell_extensions() function, as documented in the comment.
Signed-off-by: Michal Sekletar <msekleta@redhat.com>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
If link is IFF_SLAVE, extend link dev netlink attributes to include
slave attributes with new IFLA_SLAVE nest. Add netlink notification
(RTM_NEWLINK) when slave status changes from backup to active, or
visa-versa.
Adds new ndo_get_slave op to net_device_ops to fill skb with IFLA_SLAVE
attributes. Currently only used by bonding driver, but could be
used by other aggregating devices with slaves.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing support for netdevice receive queue sysfs attributes to
permit a device-specific attribute group. Initial use case for this
support will be to allow the virtio-net device to export per-receive
queue mergeable receive buffer size.
Signed-off-by: Michael Dalton <mwdalton@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_page_frag_refill currently permits only order-0 page allocs
unless GFP_WAIT is used. Change skb_page_frag_refill to attempt
higher-order page allocations whether or not GFP_WAIT is used. If
memory cannot be allocated, the allocator will fall back to
successively smaller page allocs (down to order-0 page allocs).
This change brings skb_page_frag_refill in line with the existing
page allocation strategy employed by netdev_alloc_frag, which attempts
higher-order page allocations whether or not GFP_WAIT is set, falling
back to successively lower-order page allocations on failure. Part
of migration of virtio-net to per-receive queue page frag allocators.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Michael Dalton <mwdalton@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if a device changes its mtu, first the change happens (invloving
all the side effects), and after that the NETDEV_CHANGEMTU is sent so that
other devices can catch up with the new mtu. However, if they return
NOTIFY_BAD, then the change is reverted and error returned.
This is a really long and costy operation (sometimes). To fix this, add
NETDEV_PRECHANGEMTU notification which is called prior to any change
actually happening, and if any callee returns NOTIFY_BAD - the change is
aborted. This way we're skipping all the playing with apply/revert the mtu.
CC: "David S. Miller" <davem@davemloft.net>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing a gro_list for a packet, first check the rxhash of
the incoming skb against that of the skb's in the list. This should be
a very strong inidicator of whether the flow is going to be matched,
and potentially allows a lot of other checks to be short circuited.
Use skb_hash_raw so that we don't force the hash to be calculated.
Tested by running netperf 200 TCP_STREAMs between two machines with
GRO, HW rxhash, and 1G. Saw no performance degration, slight reduction
of time in dev_gro_receive.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At first Jakub Zawadzki noticed that some divisions by reciprocal_divide
were not correct. (off by one in some cases)
http://www.wireshark.org/~darkjames/reciprocal-buggy.c
He could also show this with BPF:
http://www.wireshark.org/~darkjames/set-and-dump-filter-k-bug.c
The reciprocal divide in linux kernel is not generic enough,
lets remove its use in BPF, as it is not worth the pain with
current cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Daniel Borkmann <dxchgb@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Matt Evans <matt@ozlabs.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we don't rename the upper/lower_ifc symlinks in
/sys/class/net/*/ , which might result stale/duplicate links/names.
Fix this by adding netdev_adjacent_rename_links(dev, oldname) which renames
all the upper/lower interface's links to dev from the upper/lower_oldname
to the new name.
We don't need a rollback because only we control these symlinks and if we
fail to rename them - sysfs will anyway complain.
Reported-by: Ding Tianhong <dingtianhong@huawei.com>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They clean up the code a bit and can be used further.
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduced by:
commit 1f9248e560
"neigh: convert parms to an array"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the net_random and net_srandom macros and replaces
them with direct calls to the prandom ones. As new commits only seem to
use prandom_u32 there is no use to keep them around.
This change makes it easier to grep for users of prandom_u32.
Signed-off-by: Aruna-Hewapathirane <aruna.hewapathirane@gmail.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing net/netif_rx and net/netif_receive_skb trace events
provide little information about the skb, nor do they indicate how it
entered the stack.
Add trace events at entry of each of the exported functions, including
most fields that are likely to be interesting for debugging driver
datapath behaviour. Split netif_rx() and netif_receive_skb() so that
internal calls are not traced.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing net/net_dev_xmit trace event provides little information
about the skb that has been passed to the driver, and it is not
simple to add more since the skb may already have been freed at
the point the event is emitted.
Add a separate trace event before the skb is passed to the driver,
including most fields that are likely to be interesting for debugging
driver datapath behaviour.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to set up the partial checksum offset for IP
packets (and optionally re-calculate the pseudo-header checksum) into the
core network code.
The implementation was previously private and duplicated between xen-netback
and xen-netfront, however it is not xen-specific and is potentially useful
to any network driver.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/xfrm/xfrm_policy.c
Steffen Klassert says:
====================
This pull request has a merge conflict between commits be7928d20b
("net: xfrm: xfrm_policy: fix inline not at beginning of declaration") and
da7c224b1b ("net: xfrm: xfrm_policy: silence compiler warning") from
the net-next tree and commit 2f3ea9a95c ("xfrm: checkpatch erros with
inline keyword position") from the ipsec-next tree.
The version from net-next can be used, like it is done in linux-next.
1) Checkpatch cleanups, from Weilong Chen.
2) Fix lockdep complaints when pktgen is used with IPsec,
from Fan Du.
3) Update pktgen to allow any combination of IPsec transport/tunnel mode
and AH/ESP/IPcomp type, from Fan Du.
4) Make pktgen_dst_metrics static, Fengguang Wu.
5) Compile fix for pktgen when CONFIG_XFRM is not set,
from Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, after changing the MTU for a device, dev_set_mtu() calls
NETDEV_CHANGEMTU notification, however doesn't verify it's return code -
which can be NOTIFY_BAD - i.e. some of the net notifier blocks refused this
change, and continues nevertheless.
To fix this, verify the return code, and if it's an error - then revert the
MTU to the original one, notify again and pass the error code.
CC: Jiri Pirko <jiri@resnulli.us>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO layer has a limit of 8 flows being held in GRO list,
for performance reason.
When a packet comes for a flow not yet in the list,
and list is full, we immediately give it to upper
stacks, lowering aggregation performance.
With TSO auto sizing and FQ packet scheduler, this situation
happens more often.
This patch changes strategy to simply evict the oldest flow of
the list. This works better because of the nature of packet
trains for which GRO is efficient. This also has the effect
of lowering the GRO latency if many flows are competing.
Tested :
Used a 40Gbps NIC, with 4 RX queues, and 200 concurrent TCP_STREAM
netperf.
Before patch, aggregate rate is 11Gbps (while a single flow can reach
30Gbps)
After patch, line rate is reached.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
0-DAY kernel build testing backend reported below error:
All error/warnings:
net/core/pktgen.c: In function 'pktgen_if_write':
>> >> net/core/pktgen.c:1487:10: error: 'struct pktgen_dev' has no member named 'spi'
>> >> net/core/pktgen.c:1488:43: error: 'struct pktgen_dev' has no member named 'spi'
Fix this by encapuslating the code with CONFIG_XFRM.
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch built on top of Commit 299603e837
("net-gro: Prepare GRO stack for the upcoming tunneling support") to add
the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO
stack. It also serves as an example for supporting other encapsulation
protocols in the GRO stack in the future.
The patch supports version 0 and all the flags (key, csum, seq#) but
will flush any pkt with the S (seq#) flag. This is because the S flag
is not support by GSO, and a GRO pkt may end up in the forwarding path,
thus requiring GSO support to break it up correctly.
Currently the "packet_offload" structure only contains L3 (ETH_P_IP/
ETH_P_IPV6) GRO offload support so the encapped pkts are limited to
IP pkts (i.e., w/o L2 hdr). But support for other protocol type can
be easily added, so is the support for GRE variations like NVGRE.
The patch also support csum offload. Specifically if the csum flag is on
and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE),
the code will take advantage of the csum computed by the h/w when
validating the GRE csum.
Note that commit 60769a5dcd "ipv4: gre:
add GRO capability" already introduces GRO capability to IPv4 GRE
tunnels, using the gro_cells infrastructure. But GRO is done after
GRE hdr has been removed (i.e., decapped). The following patch applies
GRO when pkts first come in (before hitting the GRE tunnel code). There
is some performance advantage for applying GRO as early as possible.
Also this approach is transparent to other subsystem like Open vSwitch
where GRE decap is handled outside of the IP stack hence making it
harder for the gro_cells stuff to apply. On the other hand, some NICs
are still not capable of hashing on the inner hdr of a GRE pkt (RSS).
In that case the GRO processing of pkts from the same remote host will
all happen on the same CPU and the performance may be suboptimal.
I'm including some rough preliminary performance numbers below. Note
that the performance will be highly dependent on traffic load, mix as
usual. Moreover it also depends on NIC offload features hence the
following is by no means a comprehesive study. Local testing and tuning
will be needed to decide the best setting.
All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs.
(super_netperf 50 -H 192.168.1.18 -l 30)
An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1
mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123)
is configured.
The GRO support for pkts AFTER decap are controlled through the device
feature of the GRE device (e.g., ethtool -K gre1 gro on/off).
1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off
thruput: 9.16Gbps
CPU utilization: 19%
1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off
thruput: 5.9Gbps
CPU utilization: 15%
1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 12-13%
1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 10%
The following tests were performed on a different NIC that is capable of
csum offload. I.e., the h/w is capable of computing IP payload csum
(CHECKSUM_COMPLETE).
2.1 ethtool -K gre1 gro on (hence will use gro_cells)
2.1.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 8.53Gbps
CPU utilization: 9%
2.1.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 8.97Gbps
CPU utilization: 7-8%
2.1.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 8.83Gbps
CPU utilization: 5-6%
2.1.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.98Gbps
CPU utilization: 5%
2.2 ethtool -K gre1 gro off
2.2.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 5.93Gbps
CPU utilization: 9%
2.2.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 5.62Gbps
CPU utilization: 8%
2.2.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 7.69Gbps
CPU utilization: 8%
2.2.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.96Gbps
CPU utilization: 5-6%
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many cases where this feature does not improve performance or even
reduces it.
For example, here are the results from tests that I've run using 3.12.6 on one
Intel Xeon W3565 and one i7 920 connected by ixgbe adapters. The results are
from the Xeon, but they're similar on the i7. All numbers report the
mean±stddev over 10 runs of 10s.
1) latency tests similar to what is described in "c6e1a0d net: Allow no-cache
copy from user on transmit"
There is no statistically significant difference between tx-nocache-copy
on/off.
nic irqs spread out (one queue per cpu)
200x netperf -r 1400,1
tx-nocache-copy off
692000±1000 tps
50/90/95/99% latency (us): 275±2/643.8±0.4/799±1/2474.4±0.3
tx-nocache-copy on
693000±1000 tps
50/90/95/99% latency (us): 274±1/644.1±0.7/800±2/2474.5±0.7
200x netperf -r 14000,14000
tx-nocache-copy off
86450±80 tps
50/90/95/99% latency (us): 334.37±0.02/838±1/2100±20/3990±40
tx-nocache-copy on
86110±60 tps
50/90/95/99% latency (us): 334.28±0.01/837±2/2110±20/3990±20
2) single stream throughput tests
tx-nocache-copy leads to higher service demand
throughput cpu0 cpu1 demand
(Gb/s) (Gcycle) (Gcycle) (cycle/B)
nic irqs and netperf on cpu0 (1x netperf -T0,0 -t omni -- -d send)
tx-nocache-copy off 9402±5 9.4±0.2 0.80±0.01
tx-nocache-copy on 9403±3 9.85±0.04 0.838±0.004
nic irqs on cpu0, netperf on cpu1 (1x netperf -T1,1 -t omni -- -d send)
tx-nocache-copy off 9401±5 5.83±0.03 5.0±0.1 0.923±0.007
tx-nocache-copy on 9404±2 5.74±0.03 5.523±0.009 0.958±0.002
As a second example, here are some results from Eric Dumazet with latest
net-next.
tx-nocache-copy also leads to higher service demand
(cpu is Intel(R) Xeon(R) CPU X5660 @ 2.80GHz)
lpq83:~# ./ethtool -K eth0 tx-nocache-copy on
lpq83:~# perf stat ./netperf -H lpq84 -c
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to lpq84.prod.google.com () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
87380 16384 16384 10.00 9407.44 2.50 -1.00 0.522 -1.000
Performance counter stats for './netperf -H lpq84 -c':
4282.648396 task-clock # 0.423 CPUs utilized
9,348 context-switches # 0.002 M/sec
88 CPU-migrations # 0.021 K/sec
355 page-faults # 0.083 K/sec
11,812,797,651 cycles # 2.758 GHz [82.79%]
9,020,522,817 stalled-cycles-frontend # 76.36% frontend cycles idle [82.54%]
4,579,889,681 stalled-cycles-backend # 38.77% backend cycles idle [67.33%]
6,053,172,792 instructions # 0.51 insns per cycle
# 1.49 stalled cycles per insn [83.64%]
597,275,583 branches # 139.464 M/sec [83.70%]
8,960,541 branch-misses # 1.50% of all branches [83.65%]
10.128990264 seconds time elapsed
lpq83:~# ./ethtool -K eth0 tx-nocache-copy off
lpq83:~# perf stat ./netperf -H lpq84 -c
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to lpq84.prod.google.com () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
87380 16384 16384 10.00 9412.45 2.15 -1.00 0.449 -1.000
Performance counter stats for './netperf -H lpq84 -c':
2847.375441 task-clock # 0.281 CPUs utilized
11,632 context-switches # 0.004 M/sec
49 CPU-migrations # 0.017 K/sec
354 page-faults # 0.124 K/sec
7,646,889,749 cycles # 2.686 GHz [83.34%]
6,115,050,032 stalled-cycles-frontend # 79.97% frontend cycles idle [83.31%]
1,726,460,071 stalled-cycles-backend # 22.58% backend cycles idle [66.55%]
2,079,702,453 instructions # 0.27 insns per cycle
# 2.94 stalled cycles per insn [83.22%]
363,773,213 branches # 127.757 M/sec [83.29%]
4,242,732 branch-misses # 1.17% of all branches [83.51%]
10.128449949 seconds time elapsed
CC: Tom Herbert <therbert@google.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
[GIT net-next] Open vSwitch
Open vSwitch changes for net-next/3.14. Highlights are:
* Performance improvements in the mechanism to get packets to userspace
using memory mapped netlink and skb zero copy where appropriate.
* Per-cpu flow stats in situations where flows are likely to be shared
across CPUs. Standard flow stats are used in other situations to save
memory and allocation time.
* A handful of code cleanups and rationalization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the skb zerocopy logic written for nfnetlink queue available for
use by other modules.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_kobject_init() is only being called from __init context,
that is, net_dev_init(), so annotate it with __init as well, thus
the kernel can take this as a hint that the function is used only
during the initialization phase and free up used memory resources
after its invocation.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next tree,
they are:
* Add full port randomization support. Some crazy researchers found a way
to reconstruct the secure ephemeral ports that are allocated in random mode
by sending off-path bursts of UDP packets to overrun the socket buffer of
the DNS resolver to trigger retransmissions, then if the timing for the
DNS resolution done by a client is larger than usual, then they conclude
that the port that received the burst of UDP packets is the one that was
opened. It seems a bit aggressive method to me but it seems to work for
them. As a result, Daniel Borkmann and Hannes Frederic Sowa came up with a
new NAT mode to fully randomize ports using prandom.
* Add a new classifier to x_tables based on the socket net_cls set via
cgroups. These includes two patches to prepare the field as requested by
Zefan Li. Also from Daniel Borkmann.
* Use prandom instead of get_random_bytes in several locations of the
netfilter code, from Florian Westphal.
* Allow to use the CTA_MARK_MASK in ctnetlink when mangling the conntrack
mark, also from Florian Westphal.
* Fix compilation warning due to unused variable in IPVS, from Geert
Uytterhoeven.
* Add support for UID/GID via nfnetlink_queue, from Valentina Giusti.
* Add IPComp extension to x_tables, from Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Namespace related cleaning
* make cred_to_ucred static
* remove unused sock_rmalloc function
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're at it and introduced CGROUP_NET_CLASSID, lets also make
NETPRIO_CGROUP more consistent with the rest of cgroups and rename it
into CONFIG_CGROUP_NET_PRIO so that for networking, we now have
CONFIG_CGROUP_NET_{PRIO,CLASSID}. This not only makes the CONFIG
option consistent among networking cgroups, but also among cgroups
CONFIG conventions in general as the vast majority has a prefix of
CONFIG_CGROUP_<SUBSYS>.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: cgroups@vger.kernel.org
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Zefan Li requested [1] to perform the following cleanup/refactoring:
- Split cgroupfs classid handling into net core to better express a
possible more generic use.
- Disable module support for cgroupfs bits as the majority of other
cgroupfs subsystems do not have that, and seems to be not wished
from cgroup side. Zefan probably might want to follow-up for netprio
later on.
- By this, code can be further reduced which previously took care of
functionality built when compiled as module.
cgroupfs bits are being placed under net/core/netclassid_cgroup.c, so
that we are consistent with {netclassid,netprio}_cgroup naming that is
under net/core/ as suggested by Zefan.
No change in functionality, but only code refactoring that is being
done here.
[1] http://patchwork.ozlabs.org/patch/304825/
Suggested-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: cgroups@vger.kernel.org
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If user run pktgen plus ipsec by using spi, show spi value
properly when cat /proc/net/pktgen/ethX
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Introduce xfrm_state_lookup_byspi to find user specified by custom
from "pgset spi xxx". Using this scheme, any flow regardless its
saddr/daddr could be transform by SA specified with configurable
spi.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
IPsec tunnel mode encapuslation needs to set outter ip header
with right protocol/ttl/id value with regard to skb->dst->child.
Looking up a rt in a standard way is absolutely wrong for every
packet transmission. In a simple way, construct a dst by setting
neccessary information to make tunnel mode encapuslation working.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
User could set specific SPI value to arm pktgen flow with IPsec
transformation, instead of looking up SA by sadr/daddr. The reaseon
to do so is because current state lookup scheme is both slow and, most
important of all, in fact pktgen doesn't need to match any SA state
addresses information, all it needs is the SA transfromation shell to
do the encapuslation.
And this option also provide user an alternative to using pktgen
test existing SA without creating new ones.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
so /proc/net/xfrm_stat could give user clue about what's
wrong in this process.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The VLAN tag handling code in netpoll_send_skb_on_dev() has two problems.
1) It exits without unlocking the TXQ.
2) It then tries to queue a NULL skb to npinfo->txq.
Reported-by: Ahmed Tamrawi <atamrawi@iastate.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following functions are not used outside of net/core/dev.c
and should be declared static.
call_netdevice_notifiers_info
__dev_remove_offload
netdev_has_any_upper_dev
__netdev_adjacent_dev_remove
__netdev_adjacent_dev_link_lists
__netdev_adjacent_dev_unlink_lists
__netdev_adjacent_dev_unlink
__netdev_adjacent_dev_link_neighbour
__netdev_adjacent_dev_unlink_neighbour
And the following are never used and should be deleted
netdev_lower_dev_get_private_rcu
__netdev_find_adj_rcu
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function __rtnl_af_register is never called outside this
code, and the return value is always 0.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.
But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.
This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.
Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.
To facilitate this add a dev_rebuild_header(). There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP). So we need a helper function just like
dev_hard_header() to avoid crashes.
Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.
With lots of help from Florian Westphal.
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use kfree_skb_list() instead of open coding it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given we allocate memory for each cpu, we can do this
using NUMA affinities, instead of using NUMA policies
of the process changing flow_limit_cpu_bitmap value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
david decotigny