Commit Graph

823 Commits

Author SHA1 Message Date
Sourav Poddar 6691a19966 pwm: tiecap: Remove duplicate put_sync call
Remove duplicate 'pm_runtime_put_sync' in the remove path.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2014-01-23 15:19:18 +01:00
Milo Kim af66b3c093 pwm: Add LP3943 PWM driver
This is the other of the LP3943 MFD driver.
LP3943 can be used as a PWM generator, up to 2 channels.

* Two PWM generators supported

* Supported PWM operations
  request, free, config, enable and disable

* Pin assignment
  A driver data, 'pin_used' is checked when a PWM is requested.
  If the output pin is already assigned, then returns as failure.
  If the pin is available, 'pin_used' is set.
  When the PWM is not used anymore, then it is cleared.
  It is defined as unsigned long type for atomic bit operation APIs,
  but only LSB 16bits are used because LP3943 has 16 outputs.

Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-01-21 08:28:00 +00:00
Jingoo Han 82569e5b22 pwm: tiehrpwm: use dev_err() instead of pr_err()
Use dev_err() instead of pr_err() to provide a better message
to userspace.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-20 11:03:17 +01:00
Jingoo Han b07ab66391 pwm: pxa: remove unnecessary space before tabs
Remove unnecessary space before tabs in order to fix the following
checkpatch warning.

  WARNING: please, no space before tabs

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-20 10:53:55 +01:00
Jingoo Han 5eabf82ecf pwm: ep93xx: split module author names
Split module author names in order to fix the following
checkpatch warning.

  WARNING: quoted string split across lines

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-20 10:53:50 +01:00
Jingoo Han adcba1e3a5 pwm: use seq_puts() instead of seq_printf()
For a constant format without additional arguments, use seq_puts()
instead of seq_printf(). Also, the following checkpatch warning is
fixed.

  WARNING: Prefer seq_puts to seq_printf

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-20 10:53:41 +01:00
Bo Shen 6a6833563f pwm: atmel-pwm: Do not unprepare clock after successful registration
When the PWM controller is registered successfully, the clock can not
unprepare, so fix it.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-20 10:48:43 +01:00
Bo Shen 32b16d46e4 pwm: atmel-pwm: Add Atmel PWM controller driver
Add a PWM framework driver for the PWM controller found on Atmel SoCs.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[thierry.reding: coding style and other minor cleanups]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-17 11:26:42 +01:00
Axel Lin 2c80a4923a pwm: pca9685: depends on I2C rather than REGMAP_I2C
REGMAP_I2C is not a visible config option.
Thus make PWM_PCA9685 depend on I2c and then select REGMAP_I2C.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-17 10:18:07 +01:00
Laurent Pinchart 94d88d63c6 pwm: renesas-tpu: Enable driver compilation with COMPILE_TEST
This helps increasing build testing coverage.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-pwm@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-12 13:36:38 +01:00
Lars-Peter Clausen 0dc1135fdf pwm: jz4740: Use devm_clk_get()
Using the managed version of clk_get() makes the code a bit shorter and the
error paths less complicated.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-12 13:23:23 +01:00
Lars-Peter Clausen 078c6ac1bd pwm: jz4740: Pass device to clk_get()
In preparation to switching the jz4740 clk driver to the common clk framework
make sure to pass the device to clk_get().

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-12 13:23:23 +01:00
Axel Lin 6ca142ad0d pwm: sysfs: Convert to use ATTRIBUTE_GROUPS macro
Use new ATTRIBUTE_GROUPS macro to reduce the number of lines of code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-04 11:35:28 +01:00
Mike Dunn b52fa7bc5d pwm: pxa: Add device tree support
This patch adds device tree support to the PXA's PWM driver.  Nothing
needs to be extracted from the device tree node by the PWM device.
Client devices need only specify the period; the per-chip index is
implicitly zero because one device node must be present for each PWM
output in use.  This approach is more convenient due to the wide
variability in the number of PWM channels present across the various PXA
variants, and is made possible by the fact that the register sets for
each PWM channel are segregated from each other.  An of_xlate() method
is added to parse this single-cell node.  The existing ID table is
reused for the match table data.

Tested on a Palm Treo 680 (both platform data and DT cases).

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-12-04 10:18:52 +01:00
Sachin Kamat b577cdcf17 pwm: samsung: Fix kernel warning while unexporting a channel
PWM channel data was set to NULL before freeing it. This caused the
following kernel warning while unexporting the channel. Set the channel
data to NULL after freeing it.

[   70.495000] WARNING: CPU: 0 PID: 1 at drivers/base/devres.c:805 pwm_put+0x48/0x80()
[   70.505000] Modules linked in:
[   70.505000] CPU: 0 PID: 1 Comm: sh Not tainted 3.12.0-rc6-next-20131024-00012-gd4aec04-dirty #58
[   70.515000] [<c0014ddc>] (unwind_backtrace+0x0/0xf4) from [<c0011784>] (show_stack+0x10/0x14)
[   70.525000] [<c0011784>] (show_stack+0x10/0x14) from [<c03a3cbc>] (dump_stack+0x7c/0xb0)
[   70.530000] [<c03a3cbc>] (dump_stack+0x7c/0xb0) from [<c001de68>] (warn_slowpath_common+0x6c/0x88)
[   70.540000] [<c001de68>] (warn_slowpath_common+0x6c/0x88) from [<c001df20>] (warn_slowpath_null+0x1c/0x24)
[   70.550000] [<c001df20>] (warn_slowpath_null+0x1c/0x24) from [<c01d1af8>] (pwm_put+0x48/0x80)
[   70.560000] [<c01d1af8>] (pwm_put+0x48/0x80) from [<c01d21c8>] (pwm_unexport_store+0x94/0xac)
[   70.565000] [<c01d21c8>] (pwm_unexport_store+0x94/0xac) from [<c010991c>] (sysfs_write_file+0x148/0x1d8)
[   70.575000] [<c010991c>] (sysfs_write_file+0x148/0x1d8) from [<c00b2a80>] (vfs_write+0xb4/0x1a0)
[   70.585000] [<c00b2a80>] (vfs_write+0xb4/0x1a0) from [<c00b3068>] (SyS_write+0x3c/0x78)
[   70.595000] [<c00b3068>] (SyS_write+0x3c/0x78) from [<c000e2e0>] (ret_fast_syscall+0x0/0x30)

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-11-01 11:17:57 +01:00
H Hartley Sweeten a230869817 pwm: add ep93xx PWM support
Remove the non-standard EP93xx PWM driver in drivers/misc and add
a new driver for the PWM controllers on the EP93xx platform based
on the PWM framework.

These PWM controllers each support 1 PWM channel with programmable
duty cycle, frequency, and polarity inversion.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-17 16:07:19 +02:00
Wolfram Sang faed9c3808 pwm: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.

Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-15 12:16:35 +02:00
Sachin Kamat becbca1390 pwm: imx: Remove redundant of_match_ptr
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-08 15:49:38 +02:00
Sachin Kamat 3cb3b2bfdd pwm: lpc32xx: Remove redundant of_match_ptr
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-08 15:49:19 +02:00
Sachin Kamat de02cb887c pwm: mxs: Remove redundant of_match_ptr
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-08 15:49:10 +02:00
Sachin Kamat ea8eeb1502 pwm: twl: Include linux/of.h header
'of_match_ptr' is defined in linux/of.h. Include it explicitly.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-08 15:45:44 +02:00
Sachin Kamat e852340dee pwm: twl-led: Include linux/of.h header
'of_match_ptr' is defined in linux/of.h. Include it explicitly.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-08 15:45:44 +02:00
Sachin Kamat c3bdfe1f1e pwm: samsung: Include linux/of.h header
'of_match_ptr' is defined in linux/of.h. Include it explicitly.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-08 15:45:44 +02:00
Sachin Kamat 2a8876cfdf pwm: imx: Include linux/of.h header
'of_match_ptr' is defined in linux/of.h. Include it explicitly.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-08 15:45:44 +02:00
Boris BREZILLON ceb12f9398 pwm: atmel-tcb: fix max time computation for slow clk source
Use the the tcb counter width to compute the maximum time that can be
represented using the slow clock source instead of the static 16 bit width.

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-09-19 14:04:32 +02:00
Boris BREZILLON f3a82170ae pwm: atmel-tcb: add missing clk source config
Clock source changes are never applied to the CMR register.
This may lead to wrong period/duty cycle configuration.

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-09-19 14:04:24 +02:00
Linus Torvalds 8e73e367f7 ARM: SoC cleanups for 3.12
This branch contains code cleanups, moves and removals for 3.12.
 
 There's a large number of various cleanups, and a nice net removal of
 13500 lines of code.
 
 Highlights worth mentioning are:
 
 - A series of patches from Stephen Boyd removing the ARM local timer API.
 - Move of Qualcomm MSM IOMMU code to drivers/iommu.
 - Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM driver
   and switching over to the drivers/pwm one.
 - Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
 
 There's also a move of a header file out of include/linux/i2c/ to
 platform_data, where it really belongs. It touches mostly ARM platform
 code for include changes so we took it through our tree.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJSKg/NAAoJEIwa5zzehBx3vxIP/19ouV4WrzOeEMz2Id8bYT5/
 Tu9HRm+PJJ2O+4P+DYlycRAEHsbuDbwgdcqToH3quca1YnIcoJgY0FA6D0ihQ5uE
 EvTgFIpkNMLnR43GYDOE3a/rR3hYPg5oQabKFn7ZGLG2ND3D3d2N05WT8XNbTYDk
 nvCXvyRRT1ynCEzbxRBiE8x62ao4bqa5dZ1zrHHIEoakqciXEng8IU0nxx7SUarv
 61GBJHVoGFpwOWXdgt2uxyXFbn6nMrhf33ynB+RRAZhqlrC8FROj8Iz+3EoKSAHc
 fMJSw6jgdjMCfTDvi0j/eemoNC4fm0eP17Dz9WcwxtIrJPNFVrxZq+biDnpb49nM
 IHsbNrILosw9AbHr3C0kTU9tp+Jie2cE1RWHqTIN3S3zb4qN+fIJiU6o6LMhsNP5
 +ZxL4M5IYmvZYbU3a+A00TPwVRqBbsZB+et9RtYZsdpepovDiN4XcixEoT7ffqrt
 VLjJyoX7Aqmds46lMdsdD3bpPkREmMdf8aMm5fvdIqwbJi1pFMMGMdTgN2WLG5aM
 r0bj/DizxL7Brs8RHwOScUgXteZs3gg87v5Ns/3zAyJZvE4norPAiT+EJeXylpRO
 LDqqaypFs75nU+mWLNo8Fzck4Xue55SBqx5Bo3aD/Smk8B6r4KMqnMKVsV5RFHAU
 XfWb49HulUwHHdn5DAPx
 =1vE4
 -----END PGP SIGNATURE-----

Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "This branch contains code cleanups, moves and removals for 3.12.

  There's a large number of various cleanups, and a nice net removal of
  13500 lines of code.

  Highlights worth mentioning are:

   - A series of patches from Stephen Boyd removing the ARM local timer
     API.
   - Move of Qualcomm MSM IOMMU code to drivers/iommu.
   - Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
     driver and switching over to the drivers/pwm one.
   - Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).

  There's also a move of a header file out of include/linux/i2c/ to
  platform_data, where it really belongs.  It touches mostly ARM
  platform code for include changes so we took it through our tree"

* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
  ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
  gpio: (gpio-pca953x) move header to linux/platform_data/
  arm: zynq: hotplug: Remove unreachable code
  ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
  tegra: simplify use of devm_ioremap_resource
  ARM: SAMSUNG: Remove plat/regs-timer.h header
  ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
  ARM: SAMSUNG: Remove pwm-clock infrastructure
  ARM: SAMSUNG: Remove old PWM timer platform devices
  pwm: Remove superseded pwm-samsung-legacy driver
  ARM: SAMSUNG: Modify board files to use new PWM platform device
  ARM: SAMSUNG: Rework private data handling in dev-backlight
  pwm: Add new pwm-samsung driver
  ARM: mach-mvebu: remove redundant DT parsing and validation
  ARM: msm: Only compile io.c on platforms that use it
  iommu/msm: Move mach includes to iommu directory
  ARM: msm: Remove devices-iommu.c
  ARM: msm: Move mach/board.h contents to common.h
  ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
  ARM: msm: Remove TMR and TMR0 static mappings
  ...
2013-09-06 13:21:16 -07:00
Mike Dunn 1e185c7aaf pwm: pxa: Use module_platform_driver
Commit 76abbdde2d

    pwm: Add sysfs interface

causes a kernel oops due to a null pointer dereference on PXA platforms.
This happens because the class added by the patch is registered in a
subsys_initcall (initcall4), but the pxa pwm driver is registered in
arch_initcall (initcall3). If the class is not registered before the
driver probe function runs, the oops occurs in device_add() when the
uninitialized pointers in struct class are dereferenced.  I don't see a
reason that the driver must be an arch_initcall, so this patch makes it
a regular module_platform_driver (initcall6), preventing the oops.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-09-03 13:09:17 +02:00
Jingoo Han ac872bc9ed pwm: tiehrpwm: add missing __iomem annotation
Fix the following sparse warnings:

drivers/pwm/pwm-tiehrpwm.c:144:16: warning: incorrect type in argument 1 (different address spaces)
drivers/pwm/pwm-tiehrpwm.c:144:16:    expected void const volatile [noderef] <asn:2>*addr
drivers/pwm/pwm-tiehrpwm.c:144:16:    got void *
drivers/pwm/pwm-tiehrpwm.c:149:9: warning: incorrect type in argument 2 (different address spaces)
drivers/pwm/pwm-tiehrpwm.c:149:9:    expected void volatile [noderef] <asn:2>*addr
drivers/pwm/pwm-tiehrpwm.c:149:9:    got void *
drivers/pwm/pwm-tiehrpwm.c:157:18: warning: incorrect type in argument 1 (different address spaces)
drivers/pwm/pwm-tiehrpwm.c:157:18:    expected void const volatile [noderef] <asn:2>*addr
drivers/pwm/pwm-tiehrpwm.c:157:18:    got void *
drivers/pwm/pwm-tiehrpwm.c:160:9: warning: incorrect type in argument 2 (different address spaces)
drivers/pwm/pwm-tiehrpwm.c:160:9:    expected void volatile [noderef] <asn:2>*addr
drivers/pwm/pwm-tiehrpwm.c:160:9:    got void *

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-09-03 13:09:16 +02:00
Jingoo Han 3943a650f6 pwm: tiecap: add CONFIG_PM_SLEEP to ecap_pwm_{save,restore}_context()
ecap_pwm_save_context() and ecap_pwm_restore_context() are only used
when CONFIG_PM_SLEEP is selected.

drivers/pwm/pwm-tiecap.c:293:13: warning: 'ecap_pwm_save_context' defined but not used [-Wunused-function]
drivers/pwm/pwm-tiecap.c:302:13: warning: 'ecap_pwm_restore_context' defined but not used [-Wunused-function]

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-09-03 13:09:16 +02:00
Julia Lawall 88d5a2e6ff pwm: simplify use of devm_ioremap_resource
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.

Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@

- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
  ... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
  ... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
  e = devm_ioremap_resource(e1, res);
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-09-03 13:09:16 +02:00
Laurent Pinchart 382457e562 pwm: renesas-tpu: Add DT support
Specify DT bindings for the TPU PWM controller and add OF support to the
driver.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-09-03 13:09:15 +02:00
Laurent Pinchart 208be7698f pwm: Use the DT macro directly when parsing PWM DT flags
Don't redefine a PWM_SPEC_POLARITY macro with a value identical to
PWM_POLARITY_INVERTED, use the PWM DT macro directly.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-09-03 13:08:10 +02:00
Fabio Estevam cfb9e4c40e pwm: mxs: Check the return value from stmp_reset_block()
stmp_reset_block() may fail, so let's check its return value and
propagate it in the case of error.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-09-03 13:07:51 +02:00
Tomasz Figa 6059235c51 pwm: Remove superseded pwm-samsung-legacy driver
This patch removes the now unused pwm-samsung-legacy driver, which was
replaced by new pwm-samsung driver.

Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
2013-08-12 21:53:23 +02:00
Tomasz Figa 11ad39ede2 pwm: Add new pwm-samsung driver
This patch introduces new Samsung PWM driver, which is completely
rewritten to be multiplatform- and DeviceTree-aware.

In addition, remaining problems of old driver are fixed, such as:
 - proper handling of hardware variants,
 - synchronization on SMP systems,
 - handling of boundary parameter values,
 - hardware sharing with PWM clocksource driver,
 - undefined state of PWM output after stopping PWM channel.

Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
2013-08-12 21:53:22 +02:00
Tomasz Figa 615c19e160 pwm: samsung: Rename to pwm-samsung-legacy
This patch renames the old pwm-samsung driver to pwm-samsung-legacy to
create place for the new, rewritten, DT-aware pwm-samsung driver.

Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
2013-08-06 01:21:49 +02:00
Greg Kroah-Hartman 9da0175963 pwm: convert class code to use dev_groups
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead.  This converts the PWM class code to use the
correct field.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-07-29 09:08:33 +02:00
Marek Belisko b388f15fd1 pwm: pwm-tiehrpwm: Use clk_enable/disable instead clk_prepare/unprepare.
This was found when using pwm-led on am33xx and enable
heartbeat trigger.

[  808.624876] =================================
[  808.629443] [ INFO: inconsistent lock state ]
[  808.634021] 3.9.0 #2 Not tainted
[  808.637415] ---------------------------------
[  808.641981] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[  808.648288] swapper/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
[  808.653494]  (prepare_lock){+.?.+.}, at: [<c027c211>] clk_unprepare+0x15/0x24
[  808.661040] {SOFTIRQ-ON-W} state was registered at:
[  808.666155]   [<c004ec4d>] __lock_acquire+0x411/0x824
[  808.671465]   [<c004f359>] lock_acquire+0x41/0x50
[  808.676412]   [<c039ee9d>] mutex_lock_nested+0x31/0x1d8
[  808.681912]   [<c027c275>] clk_prepare+0x15/0x28
[  808.686764]   [<c0590c6b>] _init+0x117/0x1e0
[  808.691256]   [<c0019ef9>] omap_hwmod_for_each+0x29/0x3c
[  808.696842]   [<c0591107>] __omap_hwmod_setup_all+0x17/0x2c
[  808.702696]   [<c0008653>] do_one_initcall+0xc3/0x10c
[  808.708017]   [<c058a627>] kernel_init_freeable+0xa7/0x134
[  808.713778]   [<c039a543>] kernel_init+0x7/0x98
[  808.718544]   [<c000cd95>] ret_from_fork+0x11/0x3c
[  808.723583] irq event stamp: 1379172
[  808.727328] hardirqs last  enabled at (1379172): [<c03a0759>] _raw_spin_unlock_irqrestore+0x21/0x30
[  808.736828] hardirqs last disabled at (1379171): [<c03a03c3>] _raw_spin_lock_irqsave+0x13/0x38
[  808.745876] softirqs last  enabled at (1379164): [<c002ae5d>] irq_enter+0x49/0x4c
[  808.753747] softirqs last disabled at (1379165): [<c002aec3>] irq_exit+0x63/0x88
[  808.761518]
[  808.761518] other info that might help us debug this:
[  808.768373]  Possible unsafe locking scenario:
[  808.768373]
[  808.774578]        CPU0
[  808.777141]        ----
[  808.779705]   lock(prepare_lock);
[  808.783186]   <Interrupt>
[  808.785929]     lock(prepare_lock);
[  808.789595]
[  808.789595]  *** DEADLOCK ***
[  808.789595]
[  808.795805] 1 lock held by swapper/0:
[  808.799643]  #0:  (((&heartbeat_data->timer))){+.-...}, at: [<c002e204>] call_timer_fn+0x0/0x90
[  808.808814]
[  808.808814] stack backtrace:
[  808.813402] [<c000ff19>] (unwind_backtrace+0x1/0x98) from [<c039bd75>] (print_usage_bug.part.25+0x16d/0x1cc)
[  808.823721] [<c039bd75>] (print_usage_bug.part.25+0x16d/0x1cc) from [<c004e595>] (mark_lock+0x18d/0x434)
[  808.833669] [<c004e595>] (mark_lock+0x18d/0x434) from [<c004ec1d>] (__lock_acquire+0x3e1/0x824)
[  808.842803] [<c004ec1d>] (__lock_acquire+0x3e1/0x824) from [<c004f359>] (lock_acquire+0x41/0x50)
[  808.852031] [<c004f359>] (lock_acquire+0x41/0x50) from [<c039ee9d>] (mutex_lock_nested+0x31/0x1d8)
[  808.861433] [<c039ee9d>] (mutex_lock_nested+0x31/0x1d8) from [<c027c211>] (clk_unprepare+0x15/0x24)
[  808.870930] [<c027c211>] (clk_unprepare+0x15/0x24) from [<c019f7bf>] (ehrpwm_pwm_disable+0x5f/0x80)
[  808.880431] [<c019f7bf>] (ehrpwm_pwm_disable+0x5f/0x80) from [<c019f29f>] (pwm_disable+0x27/0x28)
[  808.889751] [<c019f29f>] (pwm_disable+0x27/0x28) from [<c026f8f3>] (led_heartbeat_function+0x3f/0xb0)
[  808.899431] [<c026f8f3>] (led_heartbeat_function+0x3f/0xb0) from [<c002e249>] (call_timer_fn+0x45/0x90)
[  808.909288] [<c002e249>] (call_timer_fn+0x45/0x90) from [<c002e399>] (run_timer_softirq+0x105/0x17c)
[  808.918884] [<c002e399>] (run_timer_softirq+0x105/0x17c) from [<c002abc5>] (__do_softirq+0xa5/0x150)
[  808.928486] [<c002abc5>] (__do_softirq+0xa5/0x150) from [<c002aec3>] (irq_exit+0x63/0x88)
[  808.937098] [<c002aec3>] (irq_exit+0x63/0x88) from [<c000d599>] (handle_IRQ+0x21/0x54)
[  808.945415] [<c000d599>] (handle_IRQ+0x21/0x54) from [<c0008495>] (omap3_intc_handle_irq+0x5d/0x68)
[  808.954900] [<c0008495>] (omap3_intc_handle_irq+0x5d/0x68) from [<c000c7ff>] (__irq_svc+0x3f/0x64)
[  808.964287] Exception stack(0xc05b1f68 to 0xc05b1fb0)
[  808.969587] 1f60:                   00000001 00000001 00000000 00000000 c05b0000 c0619748
[  808.978158] 1f80: c05b0000 c05b0000 c0619748 413fc082 00000000 00000000 01000000 c05b1fb0
[  808.986719] 1fa0: c004f989 c000d6f0 400f0033 ffffffff
[  808.992024] [<c000c7ff>] (__irq_svc+0x3f/0x64) from [<c000d6f0>] (cpu_idle+0x60/0x98)
[  809.000250] [<c000d6f0>] (cpu_idle+0x60/0x98) from [<c058a535>] (start_kernel+0x1e9/0x234)

Remove non atomic clk api calls and use only atomic for enable/disable because
can be called from atomic context (led_heartbeat_function is timer callback).

Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-26 23:23:54 +02:00
Axel Lin fed1bf8dc7 pwm: pca9685: Fix wrong argument to set MODE1_SLEEP bit
Current code actually does not set MODE1_SLEEP bit because the new value for
bitmask (0x1) is wrong. To set MODE1_SLEEP bit, we should pass MODE1_SLEEP
as the new value for bitmask.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-26 23:23:54 +02:00
Axel Lin 71077bc8db pwm: renesas-tpu: Add MODULE_ALIAS to make module auto loading work
This driver can be built as module, add MODULE_ALIAS to make module auto loading
work.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-26 11:48:26 +02:00
Wei Yongjun 00cf99ee00 pwm: renesas-tpu: fix return value check in tpu_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-25 12:20:06 +02:00
Laurent Pinchart 99b82abb0a pwm: Add Renesas TPU PWM driver
The Timer Pulse Unit (TPU) is a 4-channels 16-bit timer used to generate
waveforms. This driver exposes PWM functions through the PWM API for
other drivers to use.

The code is loosely based on the leds-renesas-tpu driver by Magnus Damm
and the TPU PWM driver shipped in the Armadillo EVA 800 kernel sources.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-21 11:33:28 +02:00
H Hartley Sweeten 76abbdde2d pwm: Add sysfs interface
Add a simple sysfs interface to the generic PWM framework.

  /sys/class/pwm/
  `-- pwmchipN/           for each PWM chip
      |-- export          (w/o) ask the kernel to export a PWM channel
      |-- npwm            (r/o) number of PWM channels in this PWM chip
      |-- pwmX/           for each exported PWM channel
      |   |-- duty_cycle  (r/w) duty cycle (in nanoseconds)
      |   |-- enable      (r/w) enable/disable PWM
      |   |-- period      (r/w) period (in nanoseconds)
      |   `-- polarity    (r/w) polarity of PWM (normal/inversed)
      `-- unexport        (w/o) return a PWM channel to the kernel

Based on work by Lars Poeschel.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-21 11:32:51 +02:00
Thierry Reding 3dd0a90947 pwm: Fill in missing .owner fields
Some drivers don't set the .owner fields of the struct device_driver or
struct pwm_ops, which causes the module usage count to become wrong.

Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-12 13:18:29 +02:00
Steffen Trumtrar 88b613e623 pwm: add pca9685 driver
Add pwm driver for the NXP pca9685 16 channel pwm-led controller.

The driver is really barebones at this stage. E.g. the OE' pin and
therefore the corresponding registers are not supported.
The driver was tested on a HW where this pin is tied to GND.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[thierry.reding@gmail.com: style and whitespace cleanups]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-12 13:13:18 +02:00
Boris BREZILLON 8796f9c565 pwm: atmel-tcb: prepare clk before calling enable
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-12 12:51:44 +02:00
Wolfram Sang 77f0b9d2ff pwm: devm: alloc correct pointer size
The allocated object should be the size of what the pointer is pointing
to and not the size of the pointer itself.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-10 12:50:10 +02:00
Fabio Estevam e7927141ed pwm: mxs: Let device core handle pinctrl
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.

So remove devm_pinctrl_get_select_default() from the driver.

Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-05-27 17:48:33 +02:00
Wolfram Sang 362e9cd2f5 drivers/pwm: don't check resource with devm_ioremap_resource
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
2013-05-18 11:55:58 +02:00
Axel Lin affb923df9 pwm: lpc32xx: Don't change PWM_ENABLE bit in lpc32xx_pwm_config
lpc32xx_pwm_config() is supposed to set duty_ns and period_ns,
it should not change PWM_ENABLE bit.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-23 10:58:47 +02:00
Axel Lin 08ee77b5a5 pwm: lpc32xx: Properly set PWM_ENABLE bit in lpc32xx_pwm_[enable|disable]
According to the LPC32x0 User Manual [1]:

For both PWM1 and PWM2 Control Registers:
BIT 31:
This bit gates the PWM_CLK signal and enables the external output pin
to the PWM_PIN_STATE logical level.

0 = PWM disabled. (Default)
1 = PWM enabled

So in lpc32xx_pwm_enable(), we should set PWM_ENABLE bit.
In lpc32xx_pwm_disable(), we should just clear PWM_ENABLE bit rather than
write 0 to the register which will also clear PWMx_RELOADV and PWMx_DUTY bits.

[1] http://www.nxp.com/documents/user_manual/UM10326.pdf

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-23 10:58:35 +02:00
Thierry Reding f1a8870aeb pwm: Constify OF match tables
A few drivers already annotate this properly. Make the same change for
all other OF supporting drivers.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
2013-04-23 07:42:20 +02:00
Axel Lin a46ef4d572 pwm: puv3: Remove unused enabled filed from struct puv3_pwm_chip
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:40:18 +02:00
Axel Lin 22976a5dad pwm: pxa: Remove PWM_ID_BASE macro
PWM_ID_BASE() is not used after convert to PWM framework, remove it.
Also update driver_data field of struct platform_device_id accordingly.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:40:17 +02:00
Axel Lin b3fef7f100 pwm: spear: Remove unused *dev from struct spear_pwm_chip
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:40:00 +02:00
Axel Lin 4e61573df8 pwm: mxs: Remove unused *dev from struct mxs_pwm_chip
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:33:05 +02:00
Axel Lin c8e4df3109 pwm: twl: Return proper error if twl6030_pwm_enable() fails
Return proper error instead of 0 if twl6030_pwm_enable() fails.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:32:14 +02:00
Axel Lin b014a30c59 pwm: pxa: Remove clk_enabled field from struct pxa_pwm_chip
clk_enable/clk_disable maintain an enable_count, clk_prepare and clk_unprepare
also maintain a prepare_count. These APIs will do prepare/enable when the first
user calling these APIs, and do disable/unprepare when the corresponding counter
reach 0. Thus We don't need to maintain a clk_enabled counter here.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:31:37 +02:00
Axel Lin 72da70e77f pwm: imx: Remove enabled field from struct imx_chip
We can test PWMF_ENABLED bit to know if pwm is enabled or not.
Thus remove enabled field from struct imx_chip.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:30:57 +02:00
Axel Lin d5714e8b9d pwm: twl: Add .owner to struct pwm_ops
Add missing .owner of struct pwm_ops. This prevents the module from being
removed from underneath its users.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:30:18 +02:00
Axel Lin 7fa25314d5 pwm: twl-led: Add .owner to struct pwm_ops
Add missing .owner of struct pwm_ops. This prevents the module from being
removed from underneath its users.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:29:57 +02:00
Axel Lin 83c80dc535 pwm: atmel-tcb: Add .owner to struct pwm_ops
Add missing .owner of struct pwm_ops. This prevents the module from being
removed from underneath its users.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:29:22 +02:00
Axel Lin fa0abee9b8 pwm: ab8500: Add .owner to struct pwm_ops
Add missing .owner of struct pwm_ops. This prevents the module from being
removed from underneath its users.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:29:11 +02:00
Axel Lin 563861cd63 pwm: spear: Fix checking return value of clk_enable() and clk_prepare()
The logic to check return value of clk_enable() and clk_prepare() is reversed,
fix it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-04-02 11:28:36 +02:00
Axel Lin b343a1887e pwm: tiehrpwm: Staticize non-exported symbols
Both ehrpwm_pwm_save_context() and ehrpwm_pwm_restore_context() are only used in
this file, make them static.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-03-26 16:04:03 +01:00
Axel Lin a38c989857 pwm: tiecap: Staticize non-exported symbols
Both ecap_pwm_save_context() and ecap_pwm_restore_context() are only used in
this file, make them static.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-03-26 16:04:03 +01:00
Axel Lin 622fc5d445 pwm: ab8500: Fix trivial typo in dev_err message
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-03-26 16:04:03 +01:00
Philip Avinash 1bf0f20bcc pwm: davinci: Add Kconfig support for ECAP & EHRPWM devices
Add EHRPWM and ECAP support build support for DAVINCI_DA8XX platforms.

Also, since DAVINCI platforms doesn't support TI-PWM-Subsystem module,
remove the select option for CONFIG_PWM_TIPWMSS.

Also, update CONFIG_PWM_TIPWMSS compiler directive appropriately in
pwm-tipwmss.h to fix the below compiler error upon removal of
CONFIG_PWM_TIPWMSS for DAVINCI platforms.

	drivers/pwm/pwm-tiecap.c: In function 'ecap_pwm_probe':
	drivers/pwm/pwm-tiecap.c:263:4: error: 'PWMSS_ECAPCLK_EN' undeclared
	(first use in this function)
	drivers/pwm/pwm-tiecap.c:263:4: note: each undeclared identifier
	is reported only once for each function it appears in
	drivers/pwm/pwm-tiecap.c:264:17: error: 'PWMSS_ECAPCLK_EN_ACK'
	undeclared (first use in this function)
	drivers/pwm/pwm-tiecap.c: In function 'ecap_pwm_remove':
	drivers/pwm/pwm-tiecap.c:291:49: error: 'PWMSS_ECAPCLK_STOP_REQ'
	undeclared (first use in this function)
	make[2]: *** [drivers/pwm/pwm-tiecap.o] Error 1
	make[1]: *** [drivers/pwm] Error 2
	make: *** [drivers] Error 2

Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-03-22 11:35:20 +01:00
Jingoo Han 29258b215a pwm: pwm-tiehrpwm: add CONFIG_PM_SLEEP to suspend/resume functions
This patch adds CONFIG_PM_SLEEP to suspend/resume functions to fix
the following build warning when CONFIG_PM_SLEEP is not selected.

drivers/pwm/pwm-tiehrpwm.c:562:12: warning: 'ehrpwm_pwm_suspend' defined but not used [-Wunused-function]
drivers/pwm/pwm-tiehrpwm.c:580:12: warning: 'ehrpwm_pwm_resume' defined but not used [-Wunused-function

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-03-11 08:28:22 +01:00
Jingoo Han c26e9bb4ac pwm: pwm-tipwmss: add CONFIG_PM_SLEEP to suspend/resume functions
This patch adds CONFIG_PM_SLEEP to suspend/resume functions to fix
the following build warning when CONFIG_PM_SLEEP is not selected.

drivers/pwm/pwm-tipwmss.c:104:12: warning: 'pwmss_suspend' defined but not used [-Wunused-function]
drivers/pwm/pwm-tipwmss.c:113:12: warning: 'pwmss_resume' defined but not used [-Wunused-function]

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-03-11 08:28:22 +01:00
Jingoo Han b78f5fc92a pwm: pwm-tiecap: add CONFIG_PM_SLEEP to suspend/resume functions
This patch adds CONFIG_PM_SLEEP to suspend/resume functions to fix
the following build warning when CONFIG_PM_SLEEP is not selected.

drivers/pwm/pwm-tiecap.c:314:12: warning: 'ecap_pwm_suspend' defined but not used [-Wunused-function]
drivers/pwm/pwm-tiecap.c:328:12: warning: 'ecap_pwm_resume' defined but not used [-Wunused-function]

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-03-11 08:28:22 +01:00
Jingoo Han c509a8e521 pwm: samsung: convert s3c_pwm to dev_pm_ops
Instead of using legacy suspend/resume methods, using newer dev_pm_ops
structure allows better control over power management.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-03-08 08:30:55 +01:00
Jingoo Han 482467ad97 pwm: ab8500: use devm_kzalloc()
Use devm_kzalloc() to make cleanup paths more simple.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-03-08 08:30:50 +01:00
Linus Torvalds 3eb05225ee pwm: Changes for v3.9-rc1
A new driver has been added to support the PWM mode of the timer counter
 blocks found on Atmel AT91 SoCs. The VT8500 driver now supports changing
 the PWM signal polarity and the TI drivers (EHRPWM and ECAP) gained
 suspend and resume functionality.
 
 User drivers can now query the core for whether access to a PWM device
 will sleep (if the PWM chip is on a slow bus such as I2C or SPI).
 
 The pwm-backlight driver now handles the backlight BL_CORE_FBBLANK state
 in addition to the FB layer's blanking states.
 
 To round things off, a few fixes and cleanups are also included.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIcBAABAgAGBQJRKxfbAAoJEN0jrNd/PrOhcwEP/0plVf30QDMhcan1GR3l+jmK
 3Q/cCNIWEZ75mRu+FtVYKUOduxkCOHR6LM4C2ScGnnpsS/X5oitc45FrblIwQaEI
 UeWVxDqI+pEp+rCdYVCND4lih60FJU0Cct0zZL2db4D4idF+8FRChhzwzSXhajnj
 ZZqz782Y2ig3YTLHtVGT1pp61DKxdu1Gz4U+fxo4G1/fnkquCYDzbCQovcmPSnnF
 gYB8hfxgT9JIt2cHrK6eKCHBF/4GToU+x5zDV2Ub15C2K/UQ+qgw82yl8MNd/ZS5
 rFA06iW3icnJRRc8u6hu9WVjNVNTBrUqUlFhctNB01d5jF4R6uR6aEvovT9xe8NW
 Wa5v5WrjnL6SWpZVwb/3kwwJmkeU9zKESQt5KUw3VKnT8yr2BfxcH1gJIiuW6wK7
 uYqknAvt2rwMEGzaKZJmQH682wNMxpJirs8hG9VjJc/v7AOnk6586HbRupAq8wWZ
 qK4n1Fto9RCg+b6e/hDId7+mN1GEcA5B8BOotPQ6ud+cinDZBKSbCSHhQG2LQ++F
 m81BbL82H2R2ICRoYNA74/bKq5OVOFFqHLHg5bUrG7ikdNbYOTK/4dF9qSS7DnT3
 Bi6WnKpOtfpWbHBnDunP2vBFo3f+gXmbLJdgarxk7mneV8wp0GY6TYI1awWn0hI9
 82JP3yiK5kW2JZv92o0H
 =Fcxi
 -----END PGP SIGNATURE-----

Merge tag 'for-3.9-rc1' of git://gitorious.org/linux-pwm/linux-pwm

Pull PWM changes from Thierry Reding:
 "A new driver has been added to support the PWM mode of the timer
  counter blocks found on Atmel AT91 SoCs.  The VT8500 driver now
  supports changing the PWM signal polarity and the TI drivers (EHRPWM
  and ECAP) gained suspend and resume functionality.

  User drivers can now query the core for whether access to a PWM device
  will sleep (if the PWM chip is on a slow bus such as I2C or SPI).

  The pwm-backlight driver now handles the backlight BL_CORE_FBBLANK
  state in addition to the FB layer's blanking states.

  To round things off, a few fixes and cleanups are also included"

* tag 'for-3.9-rc1' of git://gitorious.org/linux-pwm/linux-pwm:
  pwm: twl: Use to_twl() instead of container_of()
  pwm: tegra: assume CONFIG_OF
  pwm_backlight: Validate dft_brightness in main probe function
  pwm: Export pwm_{set,get}_chip_data()
  pwm: Make Kconfig entries more consistent
  pwm: Add can_sleep property to drivers
  pwm: Add pwm_can_sleep() as exported API to users
  pwm-backlight: handle BL_CORE_FBBLANK state
  pwm: pwm-tiecap: Low power sleep support
  pwm: pwm-tiehrpwm: Low power sleep support
  pwm: pwm-tiehrpwm: Update the clock handling of pwm-tiehrpwm driver
  pwm: vt8500: Add polarity support
  pwm: vt8500: Register write busy test performed incorrectly
  pwm: atmel: add Timer Counter Block PWM driver
2013-02-26 09:34:29 -08:00
Linus Torvalds 0512c04a2b Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED subsystem update from Bryan Wu.

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (61 commits)
  leds: leds-sunfire: use dev_err()/pr_err() instead of printk()
  leds: 88pm860x: Add missing of_node_put()
  leds: tca6507: Use of_get_child_count()
  leds: leds-pwm: make it depend on PWM and not HAVE_PWM
  Documentation: leds: update LP55xx family devices
  leds-lp55xx: fix problem on removing LED attributes
  leds-lp5521/5523: add author and copyright description
  leds-lp5521/5523: use new lp55xx common header
  leds-lp55xx: clean up headers
  leds-lp55xx: clean up definitions
  leds-lp55xx: clean up unused data and functions
  leds-lp55xx: clean up _remove()
  leds-lp55xx: add new function for removing device attribtues
  leds-lp55xx: code refactoring on selftest function
  leds-lp55xx: use common device attribute driver function
  leds-lp55xx: support device specific attributes
  leds-lp5523: use generic firmware interface
  leds-lp5521: use generic firmware interface
  leds-lp55xx: support firmware interface
  leds-lp55xx: add new lp55xx_register_sysfs() for the firmware interface
  ...
2013-02-26 09:29:02 -08:00
Johannes Thumshirn 30f7861703 pwm: twl: Use to_twl() instead of container_of()
Always use to_twl() for converting into private data instead of
container_of().

Signed-off-by: Johannes Thumshirn <morbidrsa@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-02-17 11:27:07 +01:00
Stephen Warren 838bf09d4f pwm: tegra: assume CONFIG_OF
Tegra only supports, and always enables, device tree. Remove all ifdefs
for DT support from the driver.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-02-15 23:27:51 +01:00
Peter Ujfalusi 261a5edd3a pwm: Add devm_of_pwm_get() as exported API for users
When booted with DT users can use devm version of of_pwm_get() to benefit
from automatic resource release.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-01 17:47:05 -08:00
Peter Ujfalusi 8eb9612799 pwm: core: Rename of_pwm_request() to of_pwm_get() and export it
Allow client driver to use of_pwm_get() to get the PWM they need. This
is needed for drivers which handle more than one PWM separately, like
leds-pwm driver, which have:

pwmleds {
	compatible = "pwm-leds";
	kpad {
		label = "omap4::keypad";
		pwms = <&twl_pwm 0 7812500>;
		max-brightness = <127>;
	};

	charging {
		label = "omap4:green:chrg";
		pwms = <&twl_pwmled 0 7812500>;
		max-brightness = <255>;
	};
};

in the dts files.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-01 17:47:05 -08:00
Thierry Reding 928c44775b pwm: Export pwm_{set,get}_chip_data()
When building a driver as a module, these functions need to be exported
for linking to succeed.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-30 09:22:24 +01:00
Thierry Reding b133d2a137 pwm: Make Kconfig entries more consistent
PWM is now consistently spelled in all uppercase letters. For the Atmel
driver the entry now also mentions Atmel to make it easier to find.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-30 09:21:35 +01:00
Florian Vaussard 2e2a0f6ed1 pwm: Add can_sleep property to drivers
Calls to PWM drivers connected through I2C can sleep.
Use the new can_sleep property.

Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-30 09:12:51 +01:00
Florian Vaussard 6e69ab1361 pwm: Add pwm_can_sleep() as exported API to users
Calls to some external PWM chips can sleep. To help users,
add pwm_can_sleep() API.

Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-30 09:12:18 +01:00
Thierry Reding 6d4294d163 pwm: Convert to devm_ioremap_resource()
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-22 11:41:57 -08:00
Philip Avinash 0d75c203ef pwm: pwm-tiecap: Low power sleep support
In low power modes of AM33XX platforms, peripherals power is cut off.
This patch supports low power sleep transition support for ECAP driver.

Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-17 16:52:59 +01:00
Philip Avinash 0e2feb17de pwm: pwm-tiehrpwm: Low power sleep support
In low power modes of AM33XX platforms, peripherals power is cut off.
This patch supports low power sleep transition support for EHRPWM
driver.

Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-17 16:52:58 +01:00
Philip, Avinash 0074b49b3f pwm: pwm-tiehrpwm: Update the clock handling of pwm-tiehrpwm driver
The clock framework has changed and it's now better to invoke
clock_prepare_enable() and clk_disable_unprepare() rather than the
legacy clk_enable() and clk_disable() calls. This patch converts the
pwm-tiehrpwm driver to the new framework.

Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-14 08:12:27 +01:00
Tony Prisk 3ccb1c1702 pwm: vt8500: Add polarity support
Add support to set polarity on PWM devices, allowing for inverted
duty cycles.

Also update the binding document to #pwm-cells = <3> to allow
passing the flags from devicetree.

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-09 08:17:12 +01:00
Tony Prisk 8ab432caa4 pwm: vt8500: Register write busy test performed incorrectly
Correct operation for register writes is to perform a busy-wait
after writing the register. Currently the busy wait it performed
before, meaning subsequent register writes to bitfields may occur
before the previous field has been updated.

Also, all registers are defined as 32-bit read/write. Change
pwm_busy_wait() to use readl rather than readb.

Improve readability of code with defines for registers and bitfields.

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-09 08:17:04 +01:00
Boris BREZILLON 9421bade07 pwm: atmel: add Timer Counter Block PWM driver
This patch adds a PWM driver based on Atmel Timer Counter Block. The
Timer Counter Block is used in Waveform generator mode.

A Timer Counter Block provides up to 6 PWM devices grouped by 2:
* group 0 = PWM 0 and 1
* group 1 = PWM 2 and 3
* group 2 = PMW 4 and 5

PWM devices in a given group must be configured with the same period
value. If a PWM device in a group tries to change the period value and
the other device is already configured with a different value an error
will be returned.

This driver requires device tree support. The Timer Counter Block number
used to create a PWM chip is given by the tc-block field in an
"atmel,tcb-pwm" compatible node.

This patch was tested on kizbox board (at91sam9g20 SoC) with pwm-leds.

Signed-off-by: Boris BREZILLON <linux-arm@overkiz.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-08 16:52:10 +01:00
Linus Torvalds 74779e2226 pwm: Changes for v3.8-rc1
A new driver has been added for the SPEAr platform and the TWL4030/6030
 driver has been replaced by two drivers that control the regular PWMs
 and the PWM driven LEDs provided by the chips.
 
 The vt8500, tiecap, tiehrpwm, i.MX, LPC32xx and Samsung drivers have all
 been improved and the device tree bindings now support the PWM signal
 polarity.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIcBAABAgAGBQJQ0XF+AAoJEN0jrNd/PrOhk5IP/RxjjfVM8z7i0xc6ykNRyv/3
 y8jRh1miwPXeamLdW07vF2NILBtDBmZ8TUbfAMt1esf25UST79Rgol/ia+QlBb3q
 w/pCDVGwlOW+2qUd34Nlb+CyKXRROIbPcFy29RZn+Z29qdkWn4LVS0nZ0UJPSPel
 80P6qxkrFGG8eKsYKB7InA0g4Ds0neWRJAoYsVp5jzyOPFpUILPdaptX+iSEk1v3
 VvkIx8eTDPZO9aqn8qL6bcE0g0AneF+dJ4qzLiswlsPMxsFIoVysw6n2JuEyy+FD
 x0Ml86Zl4SiNzZa4Pwa1250MwFT3cvnjWbAdLb2CGJVMV/uGU6nuyfXV0Aa1XtjQ
 C0k8LNshgiID8/m1/H3+/aUy9Cx/hj1KM4jchrwkCphlBiAEEryKjTPJXDwfjuBI
 s5NP4rUwfNVSQT66RaNVZ7atOKyeVu+hwAKO0h6PHOsD1GwhsT+b51/YmWXmb2E5
 OgLLOOHVFORfxCrsXRhWcHydMzfplOtfZ4smr4WG0hKUVn2Zp1DK1zDE2rCBB4X1
 ZMas4OO9uDRY9IDXZUZUtXcDPDppI6Zx3YeE1/MWzmjWqzyEYFf5OXBbakPr40Rq
 lKEwYPNf5yiqIURfFZiGDk61mrwA0Vi3i8vYfTFq1zyX9u8KbXeY8g7AhcyC1qsM
 YhfCmJZ0njopu8oENMgn
 =m+7I
 -----END PGP SIGNATURE-----

Merge tag 'for-3.8-rc1' of git://gitorious.org/linux-pwm/linux-pwm

Pull pwm changes from Thierry Reding:
 "A new driver has been added for the SPEAr platform and the
  TWL4030/6030 driver has been replaced by two drivers that control the
  regular PWMs and the PWM driven LEDs provided by the chips.

  The vt8500, tiecap, tiehrpwm, i.MX, LPC32xx and Samsung drivers have
  all been improved and the device tree bindings now support the PWM
  signal polarity."

Fix up trivial conflicts due to __devinit/exit removal.

* tag 'for-3.8-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (21 commits)
  pwm: samsung: add missing s3c->pwm_id assignment
  pwm: lpc32xx: Set the chip base for dynamic allocation
  pwm: lpc32xx: Properly disable the clock on device removal
  pwm: lpc32xx: Fix the PWM polarity
  pwm: i.MX: eliminate build warning
  pwm: Export of_pwm_xlate_with_flags()
  pwm: Remove pwm-twl6030 driver
  pwm: New driver to support PWM driven LEDs on TWL4030/6030 series of PMICs
  pwm: New driver to support PWMs on TWL4030/6030 series of PMICs
  pwm: pwm-tiehrpwm: pinctrl support
  pwm: tiehrpwm: Add device-tree binding
  pwm: pwm-tiehrpwm: Adding TBCLK gating support.
  pwm: pwm-tiecap: pinctrl support
  pwm: tiecap: Add device-tree binding
  pwm: Add TI PWM subsystem driver
  pwm: Device tree support for PWM polarity
  pwm: vt8500: Ensure PWM clock is enabled during pwm_config
  pwm: vt8500: Fix build error
  pwm: spear: Staticize spear_pwm_config()
  pwm: Add SPEAr PWM chip driver support
  ...
2012-12-19 08:19:07 -08:00
Joonyoung Shim 20e8ac3eea pwm: samsung: add missing s3c->pwm_id assignment
The s3c->pwm_id is used to calculate offset of related register.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-12-14 08:32:58 +01:00
Alban Bedel 8fc6d09dcb pwm: lpc32xx: Set the chip base for dynamic allocation
Doing so allows the base to be allocated dynamically at runtime and
makes it easier for the chip to coexist with other PWM chips.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-12-06 08:52:13 +01:00
Alban Bedel 54b2a999a1 pwm: lpc32xx: Properly disable the clock on device removal
A single clock is used for all PWMs meaning the clock's reference count
might be between 0 and N when .remove() is called. Instead of a single
clk_disable() call pwm_disable() on each PWM, to ensure that
clk_disable() is called for each PWM that is still enabled.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-12-06 08:52:11 +01:00
Alban Bedel a9a18e0691 pwm: lpc32xx: Fix the PWM polarity
The duty cycles value goes from 1 (99% HIGH) to 256 (0% HIGH) but it
is stored modulo 256 in the register as it is only 8 bits wide.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-12-06 08:52:07 +01:00
Lothar Waßmann 983290b062 pwm: i.MX: eliminate build warning
compiling the i.MX pwm driver produces the following warning:
|drivers/pwm/pwm-imx.c: In function 'imx_pwm_probe':
|drivers/pwm/pwm-imx.c:281:7: warning: assignment discards qualifiers from pointer target type

Apply a 'const' attribute to the affected variable declaration.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-12-06 08:52:04 +01:00
Thierry Reding 417328c3f7 pwm: Export of_pwm_xlate_with_flags()
Drivers may want to use this function if they support any of the flags
that can be passed via a third cell in the DT specifier. Since those
drivers may be built as modules the symbol needs to be exported to make
sure that it can be accessed.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-12-06 08:51:38 +01:00
Bill Pemberton 77f37917a6 pwm: remove use of __devexit
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-28 12:23:41 -08:00
Bill Pemberton 3e9fe83d27 pwm: remove use of __devinit
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-28 12:23:41 -08:00
Bill Pemberton fd1091125a pwm: remove use of __devexit_p
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-28 12:23:41 -08:00
Peter Ujfalusi 6179a58ec7 pwm: Remove pwm-twl6030 driver
This driver only supported the Charging indicator LED.
New set of drivers going to provide support for both PWMs and LEDs for twl4030
and twl6030 series of PMICs.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-28 15:16:20 +01:00
Peter Ujfalusi aa7656471d pwm: New driver to support PWM driven LEDs on TWL4030/6030 series of PMICs
The driver supports the following LED outputs as generic PWM driver:
TWL4030 LEDA and LEDB (PWMA and PWMB)
TWL6030 Charging indicator LED (PWM LED)

On TWL6030 when the PWM requested LED is configured to be controlled by SW.
In this case the user can enable/disable and set the duty period freely.
When the PWM has been freed, the LED driver is put back to HW control.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-28 15:16:19 +01:00
Peter Ujfalusi 3744c26386 pwm: New driver to support PWMs on TWL4030/6030 series of PMICs
The driver supports the following PWM outputs:
TWL4030 PWM0 and PWM1
TWL6030 PWM1 and PWM2

On TWL4030 the PWM signals are muxed. Upon requesting the PWM the driver
will select the correct mux so the PWM can be used. When the PWM has been
freed the original configuration is going to be restored.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-28 15:16:19 +01:00
Philip, Avinash 98ccf49daf pwm: pwm-tiehrpwm: pinctrl support
Enable pinctrl for pwm-tiehrpwm if pinctrl driver available, else
bail out with warning message.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-28 15:16:18 +01:00
Philip, Avinash 53ad9e8d37 pwm: tiehrpwm: Add device-tree binding
This patch
1. Add support for device-tree binding for EHRWPM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
   period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
   THIS_MODULE.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-28 15:16:17 +01:00
Philip, Avinash d91861dafd pwm: pwm-tiehrpwm: Adding TBCLK gating support.
Some platforms (like AM33XX) requires clock gating from control module
explicitly for TBCLK. Enabling of this clock required for the
functioning of the time base sub module in EHRPWM module. Adding support
for handling by enabling the clock on PWM device enable & disable on PWM
device disable. Platforms don't have explicit TBCLK gating has to add
dummy TBCLK node.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-28 15:16:16 +01:00
Philip, Avinash 3db9b76d7b pwm: pwm-tiecap: pinctrl support
Enable pinctrl for pwm-tiecap if pinctrl driver available, else
bail out with warning message.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-28 15:16:16 +01:00
Philip, Avinash 333b08ee8c pwm: tiecap: Add device-tree binding
This patch
1. Add support for device-tree binding for ECAP APWM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
   period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
   THIS_MODULE.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-28 15:16:15 +01:00
Philip, Avinash af0ba001d2 pwm: Add TI PWM subsystem driver
In some platforms (like am33xx), PWM sub modules (ECAP, EHRPWM, EQEP)
are integrated to PWM subsystem. These PWM submodules has resources
shared and only one register bit-field is provided to control
module/clock enable/disable, makes it difficult to handle common
resources from independent PWMSS submodule drivers.

So the solution here implemented in this patch is, to create driver for
PWMSS and take the role of parent driver for PWM submodules. PWMSS
parent driver enumerates all the child nodes under PWMSS module. Also
symbol "pwmss_submodule_state_change" exported to enable clock gating
for individual PWMSS submodules, and submodule drivers has to enable
clock gating from their drivers.

As this is only supported during DT boot, the parent/child relationship
is created and populated in DT execution flow. The only required change
is inside DTS file, making EHRPWM & ECAP as a child to PWMSS node.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-28 15:14:41 +01:00
Philip, Avinash 83af24027b pwm: Device tree support for PWM polarity
Add support for encoding PWM properties in bit encoded form with
of_pwm_xlate_with_flags() function support. Platforms require platform
specific PWM properties has to populate in 3rd cell of the pwm-specifier
and PWM driver should also set .of_xlate support with this function.
Currently PWM property polarity encoded in bit position 0 of the third
cell in pwm-specifier.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-22 22:47:12 +01:00
Tony Prisk 422470a826 pwm: vt8500: Ensure PWM clock is enabled during pwm_config
This patch corrects a bug reported by Peter Vasil.

When all PWMs are disabled, PWM module may be disabled during
calls to pwm_config. This patch enables/disables the clock in
pwm_config to ensure the module is active before register read/
writes.

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Tested-by: Peter Vasil <petervasil@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-22 22:47:12 +01:00
Tony Prisk 2f9569f7ce pwm: vt8500: Fix build error
A missing '{' causes a build error in pwm-vt8500.c

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-22 22:47:11 +01:00
Axel Lin c937136099 pwm: spear: Staticize spear_pwm_config()
spear_pwm_config() is not referenced outside of this file, make it static.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-22 22:47:10 +01:00
Shiraz Hashim ce20364bf7 pwm: Add SPEAr PWM chip driver support
Add support for PWM chips present on SPEAr platforms. These PWM
chips support 4 channel output with programmable duty cycle and
frequency.

More details on these PWM chips can be obtained from relevant
chapter of reference manual, present at following[1] location.

1. http://www.st.com/internet/mcu/product/251211.jsp

Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-22 22:47:03 +01:00
Tony Prisk 63e1ed2364 pwm: vt8500: Update vt8500 PWM driver support
This patch updates pwm-vt8500.c to support devicetree probing and
make use of the common clock subsystem.

A binding document describing the PWM controller found on
arch-vt8500 is also included.

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-11-01 16:23:19 +01:00
Linus Torvalds 2474542f64 pwm: Changes for v3.7-rc1
All legacy PWM providers have now been moved to the PWM subsystem. The
 plan for 3.8 is to adapt all board files to provide a lookup table for
 PWM devices in order to get rid of the global namespace. Subsequently,
 users of the legacy pwm_request() and pwm_free() functions can be
 migrated to the new pwm_get() and pwm_put() functions. Once this has
 been completed, the legacy API and the compatibility code in the core
 can be removed.
 
 In addition to the above, these changes also add support for configuring
 the polarity of a PWM signal (currently only supported on ECAP and
 EHRPWM) and include a much needed rework of the i.MX driver. Managed
 functions to obtain and release a PWM device (devm_pwm_get() and
 devm_pwm_put()) have been added and the pwm-backlight driver has been
 updated to use them. If the PWM subsystem hasn't been enabled, dummy
 functions are provided that allow the subsystem to safely compile out.
 
 Some common checks on input parameters have been moved to the core and
 removed from the drivers. Finally, a small fix corrects the description
 of the PWM specifier's second cell in the device tree representation.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIcBAABAgAGBQJQcV6pAAoJEN0jrNd/PrOh594P/3NHPjnTiyAZpUICX4mJeoMd
 1rX685HofCyX5jlHloS1pLRXYtIPZP97We5crNR/k/RujKcHAqAFzLtG2Jj93gxm
 nRUwLZ4xbrAgeaZeJV8YG1naWx9R1OjrK2sv+FyHRWsn9UZus2vDMV7tB0oNWo9k
 DMhtF1q7gQxx4nRu8z9FFybyItQinVREODNs+Gdv6AOJ36t+mOsGPL3LKZeFsIG3
 LdaB1p3t/07Job4KwGYYRjkOR7bIQ+ADnnO8Pkk0a9lxkMI8rA0uFbLwgyx7Hohh
 xZtm8R5il2IlHwqh52RzpShceWICxCZ3htuIXTRbVa1PSEsBzZ66W2CT7sy1jPm5
 lJlHgc7abaiwijtoG76I+Lgslv5UTViBuIYHSX4dH2kF3Jgm2SgTBNzZYePI5MMT
 BI3xc9WnwBpxgMybJsPHfU0Ff6O/9h9ab7q5lBOHkQJittahYxzWD+FgYlalcAa+
 I919iFREKNZytewLnXu+4TG0RfacQoj6D5G+SquOGmXyKYRhhJ1O6WodnRZHi/0n
 M6J0f6fLxpomI1RMn44VYP43OPJCDYxgXYoDLwCZQL9tSWYpdhXoDrjcIPO547w1
 ZS5HTXUE4DrxeYjoeqL555vtQIooM9CuH4JwKlz5zzea8NPC8eVtmNFTTWE6wKWX
 ZIOOLVvw/FI0/DSjBb8H
 =MQ5V
 -----END PGP SIGNATURE-----

Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm

Pull pwm changes from Thierry Reding:
 "All legacy PWM providers have now been moved to the PWM subsystem.
  The plan for 3.8 is to adapt all board files to provide a lookup table
  for PWM devices in order to get rid of the global namespace.
  Subsequently, users of the legacy pwm_request() and pwm_free()
  functions can be migrated to the new pwm_get() and pwm_put()
  functions.  Once this has been completed, the legacy API and the
  compatibility code in the core can be removed.

  In addition to the above, these changes also add support for
  configuring the polarity of a PWM signal (currently only supported on
  ECAP and EHRPWM) and include a much needed rework of the i.MX driver.
  Managed functions to obtain and release a PWM device (devm_pwm_get()
  and devm_pwm_put()) have been added and the pwm-backlight driver has
  been updated to use them.  If the PWM subsystem hasn't been enabled,
  dummy functions are provided that allow the subsystem to safely
  compile out.

  Some common checks on input parameters have been moved to the core and
  removed from the drivers.  Finally, a small fix corrects the
  description of the PWM specifier's second cell in the device tree
  representation."

* tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits)
  pwm: dt: Fix description of second PWM cell
  pwm: Check for negative duty-cycle and period
  pwm: Add Ingenic JZ4740 support
  MIPS: JZ4740: Export timer API
  pwm: Move PUV3 PWM driver to PWM framework
  unicore32: pwm: Use managed resource allocations
  unicore32: pwm: Remove unnecessary indirection
  unicore32: pwm: Use module_platform_driver()
  unicore32: pwm: Properly remap memory-mapped registers
  pwm-backlight: Use devm_pwm_get() instead of pwm_get()
  pwm: Move AB8500 PWM driver to PWM framework
  pwm: Fix compilation error when CONFIG_PWM is not defined
  pwm: i.MX: fix clock lookup
  pwm: i.MX: use per clock unconditionally
  pwm: i.MX: add devicetree support
  pwm: i.MX: Use module_platform_driver
  pwm: i.MX: add functions to enable/disable pwm.
  pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
  pwm: i.MX: factor out SoC specific functions
  pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
  ...
2012-10-10 20:15:24 +09:00
Thierry Reding c2d476a98f pwm: Check for negative duty-cycle and period
Make sure the duty-cycle and period passed in are not negative. This
should eventually be made implicit by making them unsigned. While at
it, the drivers' .config() implementations can have the equivalent
checks removed.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Jonghwan Choi <jhbird.choi@samsung.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: "Philip, Avinash" <avinashphilip@ti.com>
Cc: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
2012-10-05 20:56:43 +02:00
Thierry Reding f6b8a57000 pwm: Add Ingenic JZ4740 support
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
2012-10-05 20:56:42 +02:00
Thierry Reding 79c11b6fa0 pwm: Move PUV3 PWM driver to PWM framework
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Qin Rui <qinrui@mprc.pku.edu.cn>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
2012-10-05 20:56:41 +02:00
Linus Torvalds 578f1ef91a MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
 
 - TI LP8788
 - TI OMAP USB TLL
 - Maxim MAX8907
 - SMSC ECE1099
 - Dialog Semiconductor DA9055
 - A simpler syscon driver that allow us to get rid of the anatop one.
 
 Drivers are also gradually getting Device Tree and IRQ domain support.
 
 The following drivers got DT support:
 - palmas, 88pm860x, tc3589x and twl4030-audio
 
 And those ones now use the IRQ domain APIs:
 - 88pm860x, tc3589x, db8500_prcmu
 
 Also some other interesting changes:
 - Intel's ICH LPC now supports Lynx Point
 - TI's twl4030-audio added a GPO child
 - tps6527 enabled its backlight subdevice
 - The twl6030 pwm driver moved to the new PWM subsystem
 
 And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
 ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJQbVq4AAoJEIqAPN1PVmxKXOsP/ifwoqYkaGUsZ7M8b8iTTxlk
 a0/SBU1O+FDG7LbIsOyJ6VZCpipj8R4WyVqNdS2CSPVoSdT8KnakrxFY9FAtcmpA
 c6O7r+9dymcT7HeQ6mBQYYeEyXcZQkTXj9Y298zuRT88gccH5PQIOX8DTj6gKVxN
 xhuDuAWtizvwAJWfof/57p7JLilCF96Hq0UdeISD10UWJPxPmXFJTzzYw6GbPPOl
 zk1N6yig3VpK6sfK+QdqZykHFKj23RX57SmceHOISTpEr66ayuKIkJEqWm/IydMO
 XWDTT2IN80ca+1PnbrQOyiMtXg3EKrZN5WDEp2AcUiKP0fnAoZBTeuZUkqyLc3rJ
 W8LowQe6x5154CeLwcJc4+kmeGUhbj09GHKCsI7x/lQpMWgJCaGHGvLxAUE1uRZi
 4Bn9IUP7OqE465fNolLOd1fRxgzWJxe5rBYKQB7UcOrS0NThPhu0r0qV905zBrBO
 tyCZz+PexTiirpbv1K0dMTcpWeHVOmtYG5uJTmw9wTRv7jW7aUhkhkW5Q+E5BAdb
 9Rj5/vYertqI3VzRQ1w2z1SavzBO3OykTURWGDkwjfFWYbJtEdPYGGjRSFiphVYG
 8jvs5UzrDm2ICqkpkKzovVWi9lXyvNVVCgSwxHQeoPXfqb5dXLlbUZZBaCaQpRII
 XlItAJvIiUNIA8bXLoC8
 =n6lp
 -----END PGP SIGNATURE-----

Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

Pull MFD changes from Samuel Ortiz:
 "MFD bits for the 3.7 merge window.

  As usual we have a few new drivers:

   - TI LP8788
   - TI OMAP USB TLL
   - Maxim MAX8907
   - SMSC ECE1099
   - Dialog Semiconductor DA9055
   - A simpler syscon driver that allow us to get rid of the anatop one.

  Drivers are also gradually getting Device Tree and IRQ domain support.

  The following drivers got DT support:
   - palmas, 88pm860x, tc3589x and twl4030-audio

  And those ones now use the IRQ domain APIs:
   - 88pm860x, tc3589x, db8500_prcmu

  Also some other interesting changes:
   - Intel's ICH LPC now supports Lynx Point
   - TI's twl4030-audio added a GPO child
   - tps6527 enabled its backlight subdevice
   - The twl6030 pwm driver moved to the new PWM subsystem

  And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
  palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."

Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.

Guys, DON'T REBASE!

* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
  ARM: dts: Enable 88pm860x pmic
  mfd: 88pm860x: Move gpadc init into touch
  mfd: 88pm860x: Device tree support
  mfd: 88pm860x: Use irqdomain
  mfd: smsc: Add support for smsc gpio io/keypad driver
  backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
  mfd: DA9055 core driver
  mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
  mfd: wm5110: Add register patches for revision B
  mfd: wm5110: Disable control interface error report for WM5110 rev B
  mfd: max8907: Remove regulator-compatible from DT docs
  backlight: Add TPS65217 WLED driver
  mfd: Add backlight as subdevice to the tps65217
  mfd: Provide the PRCMU with its own IRQ domain
  mfd: Fix max8907 sparse warning
  mfd: Add lp8788 mfd driver
  mfd: dbx500: Provide a more accurate smp_twd clock
  mfd: rc5t583: Fix warning messages
  regulator: palmas: Add DT support
  mfd: palmas: Change regulator defns to better suite DT
  ...
2012-10-05 12:01:30 +09:00
Thierry Reding 6173f8f4ed pwm: Move AB8500 PWM driver to PWM framework
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arun Murthy <arun.murthy@stericsson.com>
2012-09-20 12:52:03 +02:00
Thierry Reding 48a364b758 pwm: Move TWL6030 PWM driver to PWM framework
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework. In order for this to work properly, register the PWM as
child of the multi-function TWL6030 device.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-19 12:04:25 +02:00
Philipp Zabel 7b27c160c6 pwm: i.MX: fix clock lookup
The i.MX PWM core has two clocks: The ipg clock and the ipg highfreq
(peripheral) clock. The ipg clock has to be enabled for this hardware
to work. The actual PWM output can either be driven by the ipg clock
or the ipg highfreq. The ipg highfreq has the advantage that it runs
even when the SoC is in low power modes.
This patch requests both clocks and enables the ipg clock for accessing
registers and the peripheral clock to actually turn on the PWM.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-12 14:25:07 +02:00
Sascha Hauer 8d1c24bfd2 pwm: i.MX: use per clock unconditionally
The i.MX PWM module has two clocks: The ipg clock and the ipg highfreq
(peripheral) clock. The ipg clock has to be enabled for this hardware
to work. The actual PWM output can either be driven by the ipg clock
or the ipg highfreq. The ipg highfreq has the advantage that it runs
even when the SoC is in low power modes.
Use the always running clock also on i.MX25.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-12 14:25:06 +02:00
Philipp Zabel 479e2e301c pwm: i.MX: add devicetree support
At the same time remove platform based support. No user for
this driver has made it into mainline so far, so all we break
is out of tree stuff.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-12 14:25:06 +02:00
Sascha Hauer 208d038f47 pwm: i.MX: Use module_platform_driver
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-12 14:25:05 +02:00
Sascha Hauer 66ad6a613a pwm: i.MX: add functions to enable/disable pwm.
We used to enable/disable the PWM only by switching the
clock on or off. Instead, use the dedicated register bits.
These differ on different SoCs, so introduce a SoC specific
function for this.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-12 14:25:05 +02:00
Sascha Hauer 140827c148 pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
The PWM core makes sure that pwm_enable/disable are called only
once. Still keep the enabled state since we will need it in
pwm_config.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-12 14:25:04 +02:00
Sascha Hauer 19e7333323 pwm: i.MX: factor out SoC specific functions
To cleanup the code and to make it easier to support different
SoCs.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-12 14:25:04 +02:00
Philip, Avinash daa5629b21 pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
EHRPWM hardware supports polarity configuration of PWM output. However
configuration of polarity done in hardware only in .enable() to ensure
PWM output present only after enabling PWM. This commit adds support for
polarity configuration for EHRPWM.
When being here, remove configuring of polarity during .config() and do
it explicitly from .set_polarity().

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-10 17:05:53 +02:00
Philip, Avinash 454870a44b pwm: pwm-tiecap: Add support for configuring polarity of PWM
ECAP APWM hardware supports polarity configuration of PWM output.
This commit adds support for polarity configuration of ECAP APWM.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-10 17:05:52 +02:00
Alexandre Courbot 6354316dbe pwm: add devm_pwm_get() and devm_pwm_put()
Add resource managed variants of pwm_get() and pwm_put() for
convenience. Code is largely inspired by the equivalent devm functions
of the regulator framework.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-10 17:05:45 +02:00
Philip, Avinash 0aa0869c3c pwm: Add support for configuring the PWM polarity
Some hardware supports inverting the polarity of the PWM signal. This
commit adds support to the PWM framework to allow users of the PWM API
to configure the polarity. Note that in order to reduce complexity,
changing the polarity of a PWM signal is only allowed while the PWM is
disabled.

A practical example where this can prove useful is to simulate inversion
of the duty cycle. While inversion of polarity and duty cycle are not
exactly the same, the differences for most use-cases are negligible.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-10 17:05:44 +02:00
Philip, Avinash 01b2d4536f pwm: pwm-tiehrpwm: Fix conflicting channel period setting
EHRPWM hardware supports 2 independent PWM channels. However the device
uses only one register to handle period setting for both channels. So
both channels should be configured for same period (in nsec).

Fix the same by returning error for conflicting period values.

However, allow
1. Configuration of period settings if not conflicting with other
channels
2. Re-configuring of period settings if no other channels being
configured

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-10 17:04:38 +02:00
Philip, Avinash c06fad9d28 pwm: pwm-tiecap: Disable APWM mode after configure
APWM mode is enabled while configuring PWM device. This was done to
handle shadow & immediate mode update of period and compare registers.
However, leaving it enabled after configuring will cause APWM output on
PWM pin even before enabling PWM device.
Fix the same by disabling APWM mode after configuring if PWM device is
not running.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-10 17:03:13 +02:00
Thierry Reding b817bf5c72 pwm: Improve Kconfig help text
The Kconfig help text should help the user understand what functionality
is provided by an option. This is especially true for new subsystems. An
improved help text is provided by this commit in the hopes of clarifying
the usefulness of the PWM framework.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Borislav Petkov <bp@alien8.de>
2012-08-20 11:58:43 +02:00
Sachin Kamat e50d3523ff pwm: core: Fix coding style issues
Fixes the following:
WARNING: line over 80 characters
ERROR: spaces required around that ':' (ctx:VxW)
WARNING: Prefer pr_warn(... to pr_warning(...

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-08-17 14:08:26 +02:00
Sachin Kamat eba7cbe5d8 pwm: vt8500: Fix coding style issue
Fixes the following:
WARNING: Prefer pr_warn(... to pr_warning(...
	pr_warning("Waiting for status bits 0x%x to clear timed out\n",

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-08-17 14:08:25 +02:00
Axel Lin 2ffdc9a648 pwm: Remove a redundant error message when devm_request_and_ioremap fails
The implementation in devm_request_and_ioremap() already shows error message,
so no need to show dev_err again if devm_request_and_ioremap() fails.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-08-17 14:08:25 +02:00
Jingoo Han ecefeb7921 pwm: samsung: add missing device pointer to struct pwm_chip
This patch adds missing device pointer to struct pwm_chip. If the
device pointer is NULL, pwmchip_add() will return error.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-08-17 14:08:24 +02:00
Sachin Kamat dfeb86ecde pwm: Add missing static storage class specifiers in core.c file
Fixes the following sparse warnings:
drivers/pwm/core.c:152:6: warning:
symbol 'of_pwmchip_add' was not declared. Should it be static?
drivers/pwm/core.c:165:6: warning:
symbol 'of_pwmchip_remove' was not declared. Should it be static?

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-08-17 14:08:24 +02:00
Philip, Avinash 19891b20e7 pwm: pwm-tiehrpwm: PWM driver support for EHRPWM
Enhanced high resolution PWM module (EHRPWM) hardware can be used to
generate PWM output over 2 channels. This commit adds PWM driver support
for EHRPWM device present on AM33XX SOC. Current implementation supports
simple PWM functionality.

Reviewed-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-26 07:45:20 +02:00
Philip, Avinash 8e0cb05b3b pwm: pwm-tiecap: PWM driver support for ECAP APWM
ECAP hardware on AM33XX SOC supports auxiliary PWM (APWM) feature. This
commit adds PWM driver support for ECAP hardware on AM33XX SOC.

In the ECAP hardware, each PWM pin can also be configured to be in
capture mode. Current implementation only supports PWM mode of
operation. Also, hardware supports sync between multiple PWM pins but
the driver supports simple independent PWM functionality.

Reviewed-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-26 07:44:52 +02:00
Thierry Reding d295b12976 pwm: fix used-uninitialized warning in pwm_get()
Some versions of GCC don't seem no notice that the initialization of the
index variable is tied to that of the chip variable and falsely report
it as potentially being used uninitialized. However, to save anybody
else from tripping over this, we now initialize the index variable
unconditionally.

Originally-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:24:17 +02:00
Alexandre Pereira da Silva 2132fa8d95 pwm: add lpc32xx PWM support
Add lpc32xx SOC PWM driver.

Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:24:05 +02:00
Sachin Kamat 2437b0d95c pwm: Use pr_* functions in pwm-samsung.c file
Replace printk with pr_* functions to avoid checkpatch warnings.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:24:03 +02:00
Axel Lin 6192fa8744 pwm: Convert pwm-samsung to use devm_* APIs
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:24:03 +02:00
Axel Lin 0c8f527d8c pwm: Convert pwm-tegra to use devm_clk_get()
Also return proper error in tegra_pwm_remove() if pwmchip_remove()
fails.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:24:02 +02:00
Axel Lin 457fd768ee pwm: pwm-mxs: Return proper error if pwmchip_remove() fails
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:24:01 +02:00
Axel Lin b50675dcc3 pwm: pwm-bfin: Return proper error if pwmchip_remove() fails
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:24:00 +02:00
Thierry Reding abeaf75527 pwm: pxa: Propagate pwmchip_remove() error
If the pwmchip_remove() call fails, propagate the error to the driver's
remove callback. This is required to prevent the module from being
unloaded if a PWM provided by the driver is still in use.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:23:59 +02:00
Axel Lin 45b301d2b1 pwm: Convert pwm-pxa to use devm_* APIs
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:23:59 +02:00
Axel Lin 261995dd30 pwm: Convert pwm-vt8500 to use devm_* APIs
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:23:58 +02:00
Axel Lin a9970e3bec pwm: Convert pwm-imx to use devm_* APIs
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:23:57 +02:00
Thierry Reding eac7a92fd0 pwm: Conflict with legacy PWM API
In order to avoid duplicate symbols with legacy PWM API implementations,
the new PWM framework needs to conflict with any of the existing legacy
implementations. This is done in two ways: for implementations provided
by drivers, a conflict is added to the driver to ensure it will have to
be ported to the PWM subsystem before it can coexist with other PWM
providers. For architecture-specific code, the conflict is added to the
PWM symbol to avoid confusion when a previously picked platform or
machine can no longer be selected because of the PWM subsystem being
included.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:23:56 +02:00
Shawn Guo 1112fe88d4 pwm: pwm-mxs: add pinctrl support
Call pinctrl subsystem to set up pwm pin.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:23:56 +02:00
Shawn Guo 22d260bd88 pwm: pwm-mxs: use devm_* managed functions
Use devm_* managed functions to have a clean fail-out.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:23:55 +02:00
Shawn Guo 01bf32e949 pwm: pwm-mxs: use global reset function stmp_reset_block
Use global reset function stmp_reset_block instead of mxs_reset_block
to remove <mach/common.h> inclusion.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:23:54 +02:00
Shawn Guo 071407eefd pwm: pwm-mxs: encode soc name in compatible string
Encode soc name in the compatible string to know the specific version
hardware block.  This is the general approach adopted for most bindings.
Change mxs-pwm binding to use the approach.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:23:53 +02:00
Shawn Guo 4dce82c1e8 pwm: add pwm-mxs support
Add generic PWM framework driver (DT only) for Freescale MXS.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-02 22:06:34 +02:00
Sascha Hauer a245ccebb4 ARM vt8500: Move vt8500 pwm driver to pwm framework
Move the driver to drivers/pwm/ and convert it to use the framework.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-02 22:06:33 +02:00
Sascha Hauer 215c29d3d0 ARM Samsung: Move s3c pwm driver to pwm framework
Move the driver to drivers/pwm/ and convert it to use the framework.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
[eric@eukrea.com: fix pwmchip_add return code test]
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-02 21:39:02 +02:00
Sascha Hauer 29693248ed ARM i.MX: Move i.MX pwm driver to pwm framework
Move the driver to drivers/pwm/ and convert it to use the framework.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[eric@eukrea.com: set chip.dev to prevent probe failure]
[eric@eukrea.com: fix pwmchip_add return code test]
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-02 21:39:01 +02:00
Thierry Reding 17b2b4780f pwm: Move PXA PWM driver to PWM framework
This commit moves the PXA PWM driver to the drivers/pwm subdirectory and
converts it to use the new PWM framework.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-02 21:39:00 +02:00
Thierry Reding a4315e3c11 pwm: Move Blackfin PWM driver to PWM framework
This commit moves the Blackfin PWM driver to the drivers/pwm sub-
directory and converts it to register with the new PWM framework.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-02 21:38:59 +02:00
Thierry Reding 140fd977dc pwm: tegra: Add device tree support
Add auxdata to instantiate the PWFM controller from a device tree,
include the corresponding nodes in the dtsi files for Tegra 20 and
Tegra 30 and add binding documentation.

Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-02 21:38:59 +02:00
Thierry Reding 0134b932a0 pwm: Add NVIDIA Tegra SoC support
This commit adds a generic PWM framework driver for the PWFM controller
found on NVIDIA Tegra SoCs. The driver is based on code from the
Chromium kernel tree and was originally written by Gary King (NVIDIA)
and later modified by Simon Que (Chromium).

Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-02 21:38:57 +02:00
Thierry Reding 7299ab70e6 pwm: Add device tree support
This patch adds helpers to support device tree bindings for the generic
PWM API. Device tree binding documentation for PWM controllers is also
provided.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-06-15 12:56:57 +02:00
Thierry Reding 8138d2ddbc pwm: Add table-based lookup for static mappings
In order to get rid of the global namespace for PWM devices, this commit
provides an alternative method, similar to that of the regulator or
clock frameworks, for registering a static mapping for PWM devices. This
works by providing a table with a provider/consumer map in the board
setup code.

With the new pwm_get() and pwm_put() functions available, usage of
pwm_request() and pwm_free() becomes deprecated.

Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-06-15 12:56:53 +02:00
Thierry Reding 62099abf67 pwm: Add debugfs interface
This commit adds a debugfs interface that can be used to list the
current internal state of the PWM devices registered with the PWM
framework.

Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-06-15 12:56:53 +02:00
Thierry Reding f051c466cf pwm: Allow chips to support multiple PWMs
Many PWM controllers provide access to more than a single PWM output and
may even share some resource among them. Allowing a PWM chip to provide
multiple PWM devices enables better sharing of those resources. As a
side-effect this change allows easy integration with the device tree
where a given PWM can be looked up based on the PWM chip's phandle and a
corresponding index.

This commit modifies the PWM core to support multiple PWMs per struct
pwm_chip. It achieves this in a similar way to how gpiolib works, by
allowing PWM ranges to be requested dynamically (pwm_chip.base == -1) or
starting at a given offset (pwm_chip.base >= 0). A chip specifies how
many PWMs it controls using the npwm member. Each of the functions in
the pwm_ops structure gets an additional argument that specified the PWM
number (it can be converted to a per-chip index by subtracting the
chip's base).

The total maximum number of PWM devices is currently fixed to 1024 while
the data is actually stored in a radix tree, thus saving resources if
not all of them are used.

Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
[eric@eukrea.com: fix error handling in pwmchip_add]
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-06-15 12:56:52 +02:00
Sascha Hauer 0c2498f166 pwm: Add PWM framework support
This patch adds framework support for PWM (pulse width modulation) devices.

The is a barebone PWM API already in the kernel under include/linux/pwm.h,
but it does not allow for multiple drivers as each of them implements the
pwm_*() functions.

There are other PWM framework patches around from Bill Gatliff. Unlike
his framework this one does not change the existing API for PWMs so that
this framework can act as a drop in replacement for the existing API.

Why another framework?

Several people argue that there should not be another framework for PWMs
but they should be integrated into one of the existing frameworks like led
or hwmon. Unlike these frameworks the PWM framework is agnostic to the
purpose of the PWM. In fact, a PWM can drive a LED, but this makes the
LED framework a user of a PWM, like already done in leds-pwm.c. The gpio
framework also is not suitable for PWMs. Every gpio could be turned into
a PWM using timer based toggling, but on the other hand not every PWM hardware
device can be turned into a gpio due to the lack of hardware capabilities.

This patch does not try to improve the PWM API yet, this could be done in
subsequent patches.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
[thierry.reding@avionic-design.de: fixup typos, kerneldoc comments]
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-06-15 12:56:50 +02:00