When copying the MAC RAR registers to PHY there is an error in the
calculation of the rar_entry_count, which causes a write of unknown/
undefined register space in the MAC to unknown/undefined register space in
the PHY.
This patch fixes the overrun with writing to the PHY RAR and also fixes the
ethtool offline register tests so that the correctly addressed registers
have the appropriate bitmasks for R/W and RO bits for affected parts.
Shawn Rader gets credit for finding and fixing the register overrun.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
CC: Shawn Rader <shawn.t.rader@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The initialization of the PHY on I217/I218, while similar to 82579, must
also check to see if the MAC and PHY are in the same mode (PCIe vs. SMBus)
otherwise the PHY will be inaccessible by the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device IDs 0x15a0 and 0x15a1 are new SKUs that contain the same MAC as
I217 and same PHY as I218.
The device IDs 0x15a2 and 0x15a3 are the same as existing I218 SKUs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tx hang is an unintended consequence of another workaround that is in the
EEPROM for an issue with the firmware at 10Mbps when K1 (a power mode of
the MAC-PHY interconnect) is enabled. The issue is resolved by setting
appropriate Tx re-transmission timeouts in the PHY and associated K1 entry
times in the MAC to allow enough transmissions to occur without triggering
a Tx hang. A similar change is needed when linked at 10Mbps to improve
latency.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the Latency Tolerance Reporting (LTR) values for the "PCIe-like"
GbE MAC in the Lynx Point PCH based on Rx buffer size and link speed
when link is up (which must not exceed the maximum latency supported
by the platform), otherwise specify there is no LTR requirement.
Unlike true-PCIe devices which set the LTR maximum snoop/no-snoop
latencies in the LTR Extended Capability Structure in the PCIe Extended
Capability register set, on this device LTR is set by writing the
equivalent snoop/no-snoop latencies in the LTRV register in the MAC and
set the SEND bit to send an Intel On-chip System Fabric sideband (IOSF-SB)
message to the PMC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that IEEE802.3az-2010 Energy Efficient Ethernet has been approved as
standard (September 2010) and the driver can enable and disable it via
ethtool, enable the feature by default on parts which support it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Devices supported by the driver which support EEE (currently 82579, I217
and I218) are advertising EEE capabilities during auto-negotiation even
when EEE has been disabled. In addition to not acting as expected, this
also caused the EEE status reported by 'ethtool --show-eee' to be wrong
when two of these devices are connected back-to-back and EEE is disabled
on one. In addition to fixing this issue, the ability for the user to
specify which speeds (100 or 1000 full-duplex) to advertise EEE support
has been added.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the MAC and PHY are in two different modes (different power levels
and interconnect speeds), it could take a long time before a PHY register
access timed out using the existing MAC-PHY interconnect configuration
coded into the driver for ICH- and PCH-based LOMs. Introduce an I217/I218-
specific .setup_physical_interface operation which does not override the
interconnect configuration in the NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Two 82579 LOMs connected via a 10Mb hub experience extraordinarily low
performance. This is because 82579 is excessively aggressive on transmit
at 10Mb half-duplex and will not provide sufficient time for the link
partner to transmit. When the link partner is also 82579, the result is a
lot of collisions (and corresponding re-transmits) that cause the poor
performance. To work-around this issue, significantly increase the IPG in
the MAC to allow enough gap for the link partner to transmit and reduce the
Rx latency in the analog PHY to 0 to reduce the number of collisions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/netdev.c
Minor conflict in e1000e, a line that got fixed in 'net'
has been removed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve strict checkpatch USLEEP_RANGE checks by converting delays and
sleeps as described in ./Documentation/timers/timers-howto.txt. Three
other violations of the text have also been fixed.
CHECK:USLEEP_RANGE: usleep_range is preferred over udelay; see
Documentation/timers/timers-howto.txt
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cuddle broken lines where appropriate.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CHECK:SPACING: No space is necessary after a cast
CHECK:SPACING: space prohibited before semicolon
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ERROR:SPACING: spaces prohibited around that ':' (ctx:WxV)
ERROR:SPACING: need consistent spacing around '-' (ctx:WxV)
ERROR:SPACING: space required after that ',' (ctx:VxV)
ERROR:SPACING: spaces required around that '=' (ctx:VxV)
WARNING:SPACING: missing space after enum definition
and some similar spacing issues not reported by checkpatch.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ERROR:CODE_INDENT: code indent should use tabs where possible
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
At 1000Mbps link speed, one of the MAC's internal clocks can be stopped for
up to 4us when entering K1 (a power mode of the MAC-PHY interconnect). If
the MAC is waiting for completion indications for 2 DMA write requests into
Host memory (e.g. descriptor writeback or Rx packet writing) and the
indications occur while the clock is stopped, both indications will be
missed by the MAC causing the MAC to wait for the completion indications
and be unable to generate further DMA write requests. This results in an
apparent hardware hang.
Work-around the issue by disabling the de-assertion of the clock request
when 1000Mbps link is acquired (K1 must be disabled while doing this).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve the following strict checkpatch checks:
CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
CHECK:BRACES: braces {} should be used on all arms of this statement
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines and function prototypes specific to the ICH/PCH family of
devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566,
ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new
ich8lan.h header file (the convention for Intel wired ethernet drivers is
to use the name of the first device in the family for related file and
function names). These defines and function prototypes can be used by
other files in the driver and moving them to the ICH/PCH-family-specific
file makes it clearer to which devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For standard IEEE MII-compatible transceivers, the kernel has generic
register and bit definitions. Use those instead of redundant local
defines.
Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000)
when it is not necessary (i.e. when it is bitwise OR'ed with another
value).
Some whitespace issues in the surrounding context of the above changes are
also cleaned up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the unused parameter when possible, otherwise use __always_unused
attribute.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The largest jumbo frame supported by the 82579 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In keeping with the e1000e driver function naming convention, the subject
function is renamed to indicate it is generic, i.e. it is applicable to
more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis with cppcheck has shown a few instances of a variable
being reassigned a value before the old one has been used. None of these
ever require the old value to be used so remove the old values.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis with cppcheck has shown a few instances of a variable which
is assigned a value that is never used. A number of these are the return
status of various driver function calls which should be passed back to the
caller of the current function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...and cleanup some whitespace in other prototypes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it
back to power-on defaults. This includes setting it's MAC-PHY messaging
mode to use the PCIe-like interconnect, so the MAC must also be set back
from SMBus mode to PCIe mode otherwise the PHY can be inaccessible.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The largest jumbo frame supported by the i217 and i218 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As done with the previous generation managed 82579, prevent the PHY from
being put into an unknown state by blocking the hardware from automatically
configuring the PHY as done with the previous generation managed 82579.
Instead, the driver should configure the PHY with contents of the EEPROM
image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On 82574, 82583, 82579, I217 and I218 add support for hardware time
stamping of all or no Rx packets and Tx packets which have the
SKBTX_HW_TSTAMP flag set. Update the .get_ts_info ethtool operation to
report the supported time stamping modes, and enable and disable hardware
time stamping with the SIOCSHWTSTAMP ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the ability to query and set Energy Efficient Ethernet parameters via
ethtool for applicable devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...discovered during code inspection.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Energy Efficient Ethernet on 82579 and I217 should only be enabled if not
disabled by the user, if the link is full duplex and the link partner has
similar EEE capabilities (stored in different EMI registers on the two
different parts).
After enabling EEE, read the IEEE MMD register 3.1 (which is also stored in
different EMI registers on the two different parts) to clear the count of
received Tx/Rx LPI indications.
Also, rename I217_EEE_100_SUPPORTED to I82579_EEE_100_SUPPORTED to indicate
the bit is valid starting with I82579 (released before I217).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When connected to certain switches, the 82577 PHY might drop link
unexpectedly. Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Extended Management Interface (EMI) registers are accessed by first
writing the EMI register offset to the EMI_ADDR regiter and then either
reading or writing the data to/from the EMI_DATA register. Add helper
functions for performing these steps and convert existing EMI register
accesses accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On I217, the bit that indicates an invalid EEPROM (NVM) image checksum has
changed from previous ICH/PCH LOMs. When validating the EEPROM checksum,
check the appropriate bit on different devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update comments to conform to the preferred style for networking code as
described in ./Documentation/CodingStyle and checked for in the recently
added checkpatch NETWORKING_BLOCK_COMMENT_STYLE test.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Occasionally, the PHY can be initially inaccessible when the first read of
a PHY register, e.g. PHY_ID1, happens (signified by the returned value
0xFFFF) but subsequent accesses of the PHY work as expected. Add a retry
counter similar to how it is done in the generic e1000_get_phy_id().
Also, when the PHY is completely inaccessible (i.e. when subsequent reads
of the PHY_IDx registers returns all F's) and the MDIO access mode must be
set to slow before attempting to read the PHY ID again, the functions that
do these latter two actions expect the SW/FW/HW semaphore is not already
set so the semaphore must be released before and re-acquired after calling
them otherwise there is an unnecessarily inordinate amount of delay during
device initialization.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i217 is the next-generation LOM that will be available on systems with the
Lynx Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, IPv6 extension header parsing was disabled for all devices
supported by e1000e when using packet split mode. However, as per a
silicon errata, only certain devices need this restriction and will need
to disable IPv6 extension header parsing for all modes.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling the locked versions of the read/write PHY ops function pointers
often produces excessively long lines. Shorten these as is done with
the non-locked versions of the PHY register read/write functions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Secondary unicast and multicast addresses are added to the Receive
Address registers (RAR) for most parts supported by the driver. For
82579, there is only one actual RAR and a number of Shared Receive Address
registers (SHRAR) that are shared among the driver and f/w which can be
reserved and write-protected by the f/w. On this device, use the SHRARs
that are not taken by f/w for the additional addresses.
Add a MAC ops function pointer infrastructure (similar to other MAC
operations in the driver) for setting RARs, introduce a new rar_set
function for 82579 and convert the existing code that sets RARs on other
devices to a generic rar_set function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY initialization flows and assorted workarounds for 82577/8/9 done
during driver load and resume from Sx should be the same yet they are not.
Combine the current flows/workarounds into a common set of functions that
are called during the different code paths.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David Ertman