IT8786E is mostly compatible with IT8771 / IT8772.
Parameters determined by testing various combinations.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Thomas Lorblanches <zlika_ese@hotmail.com>
[Guenter Roeck: merged from github, addressed review comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TS3000GB0 has a new device ID (0x2913). Since IDT's datasheets suggest
that the upper 8 bit of the device ID reflect the chip ID and the lower
8 bit reflect the version number, modify the code to accept all chips
with ID 0x29xx.
Also add support for TS3001 and TSE2004.
Some of the datasheets for older chips are no longer available from
the IDT web site, so replace explicit links in the documentation with
a generic note.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8781F is mostly compatible to IT8782F. Major difference is that it only
supports four instead of six UART channels, and therefore does not share
the uart6 pins.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for "ina231" as compatible string, and update
Documentation and Kconfig accordingly.
Tested with the Exynos5422-based odroid-xu3 board which has on-board
INA231 sensors.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This attribute allows to configure the update interval of ina226. Although
the bus and shunt voltage conversion times remain hardcoded to 1.1 ms, we can
now modify said interval by changing the averaging rate.
While we're at it - add an additional variable to ina2xx_data, which holds
the current configuration settings - this way we'll be able to restore the
configuration in case of an unexpected chip reset.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt resistance can only be set via platform_data or device tree. This
isn't suitable for devices in which the shunt resistance can change/isn't
known at boot-time.
Add a sysfs attribute that allows to read and set the shunt resistance.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP435 supports a range of I2C addresses, not just 0x4c.
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95233 is similar to LM95234, but it only supports two
instead of four external temperature sensors.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95235 is register compatible to LM95245.
Also update link to LM95245 data sheet, and drop the link to the
datasheet from the driver source to simplify code maintenance.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6792D is similar to NCT6791D. Only beep control and temperature
monitoring registers are different.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document support for NCT6102D/NCT6104D/NCT6106D and NCT6791D.
Document that NCT5573D is compatible to NCT6775F with the same chip ID.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is basically a faster lm75 with improved (11 bit) resolution.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added driver to support the 14F021P00 BMC Hardware Monitoring.
The BMC is a Board Management Controller including monitoring of the
board voltages.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds temperature monitoring support for F15h M60h processor.
- Add new pci device id for the relevant processor
- The functionality of REG_REPORTED_TEMPERATURE is moved to
D0F0xBC_xD820_0CA4 [Reported Temperature Control]
- So, use this to get CUR_TEMP value
- Since we need an indirect register access, protect this with
a mutex lock
- Add Kconfig, Doc entries to indicate support for this processor.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
[Guenter Roeck: Declare new mutex and function static]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pwm-fan driver enables control of fans connected to PWM lines.
This driver uses the PWM framework, so it is compatible with all
PWM devices that provide drivers through the PWM framework.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
[Guenter Roeck: Last argument to devm_of_pwm_get is pointer, use NULL]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For TI power management chip TPS40422, READ_TEMPERATURE_2 command is supported on
page 1 of the chip, but the original driver(pmbus.c) only tried to detect this command
on page 0, this will lead to a result that the temperature sensor in page 1 couldn't
be detected. This change is to isolate the tps40422 driver from pmbus.c into a solo
front-end driver.
Signed-off-by: Zhu Laiwen <richard.zhu@nsn.com>
[Guenter Roeck: Dropped unnecessary license text (fixes checkpatch warning)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Not all supported chips support the entire I2C address range.
Only accept specific chips at the addresses supported by that chip.
Check for invalid values in conversion rate and status registers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
This patch adds support for the ntc thermistor B57330V2103 from EPCOS.
Signed-off-by: Johannes Pointner <johannes.pointner@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102
by having only 8 bit registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
[linux@roeck-us.net: Select REGMAP_I2C in Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for Lattice's POWR1220 power manager IC. Read
access to all the ADCs on the chip are supported through the hwmon
sysfs files.
Signed-off-by: Scott Kanowitz <skanowitz@echo360.com>
[Guenter Roeck: Removed some extra ( )]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Murata Manufacturing Co., Ltd is the vendor for
NTC (Negative Temperature coefficient) based Thermistors.
But, the driver extensively uses "NTC" as the vendor name.
This patch corrects the vendor name also updates the
compatibility strings according to the vendor-prefix.txt
Note: Drivers continue to support the previous compatible strings
but further addition of these compatible strings in device tree
is deprecated.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Sensirion SHTC1 and compatible temperature and humidity
sensors.
Signed-off-by: Tomas Pop <tomas.pop@sensirion.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New chip support to existing drivers:
Add support for STTS2004 and AT30TSE004 to jc42 driver
Add support for EMC1402/EMC1412/EMC1422 to emc1403 driver
Other notable changes:
Document hwmon kernel API
Convert jc42, lm70, lm75, lm77, lm83, lm92, max1619, tmp421,
and tmp102 drivers to use new hwmon API functions
Replace function macros in lm80, lm92, and jc42 drivers with
real code
Convert emc1403 driver to use regmap, add support for additional
attributes, and add device IDs for EMC1412, EMC1413, and EMC1414
Various additional cleanup and minor bug fixes in several drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dytt
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging into next
Pull hwmon updates from Guenter Roeck:
"New driver for NCT6683D
New chip support to existing drivers:
- add support for STTS2004 and AT30TSE004 to jc42 driver
- add support for EMC1402/EMC1412/EMC1422 to emc1403 driver
Other notable changes:
- document hwmon kernel API
- convert jc42, lm70, lm75, lm77, lm83, lm92, max1619, tmp421, and
tmp102 drivers to use new hwmon API functions
- replace function macros in lm80, lm92, and jc42 drivers with real
code
- convert emc1403 driver to use regmap, add support for additional
attributes, and add device IDs for EMC1412, EMC1413, and EMC1414
- various additional cleanup and minor bug fixes in several drivers"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (60 commits)
hwmon: (nct6775) Fix probe unwind paths to properly unregister platform devices
hwmon: (nct6683) Fix probe unwind paths to properly unregister platform devices
hwmon: (ultra45_env) Introduce managed version of kzalloc
hwmon: Driver for NCT6683D
hwmon: (lm80) Rearrange code to avoid forward declarations
hwmon: (lm80) Convert fan display function macros into functions
hwmon: (lm80) Convert voltage display function macros into functions
hwmon: (lm80) Convert temperature display function macros into functions
hwmon: (lm80) Normalize all temperature values to 16 bit
hwmon: (lm80) Simplify TEMP_FROM_REG
hwmon: (lm83) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm83) Rearange code to avoid forward declarations
hwmon: (lm83) Drop FSF address
hwmon: (max1619) Convert to use devm_hwmon_device_register_with_groups
hwmon: (max1619) Drop function macros
hwmon: (max1619) Rearrange code to avoid forward declarations
hwmon: (max1619) Drop FSF address
hwmon: (max1619) Fix critical alarm display
hwmon: (jc42) Add support for STTS2004 and AT30TSE004
hwmon: (jc42) Convert function macros into functions
...
The temp[1-*]_min_hyst sysfs attribute is already implemented by 3
hwmon drivers (adt7x10, lm77 and lm92) but was missing from the
standard interface.
Also add temp[1-*]_lcrit_hyst for consistency, even though no driver
implement that one for the time being.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Also fix links to datasheets for other supported sensors from
ST Microelectronics, and add links to several Atmel datasheets.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips in this chip series only support a single hysteresis value. Having
multiple writable hysteresis attributes is therefore confusing, since a single
write affects all hysteresis temperatures. Make all but one (temp1_crit_hyst)
read-only.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With the driver now supporting several chip variants,
it is about time to document what is supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hwmon subsystem has been around for a while. Time to document
its kernel API.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Updating the hysteresis value when updating the critical temperature limit
was following the rule of 'least surprise'. However, it had the undesirable
side effect of changing the hysteresis for all other attributes, which
defeats the purpose of least surprise. In addition, it could result in
invalid hysteresis values if the resulting hysteresis was too large. In such
cases the resulting hysteresis ended up changed anyway, which again defeats
the purpose. So drop that code and document the new behavior.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Jean Delvare:
"This includes a number of driver conversions to
devm_hwmon_device_register_with_groups, a few cleanups, and
support for the ITE IT8623E"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (it87) Add support for IT8623E
hwmon: (it87) Fix IT8603E define name
hwmon: (lm90) Convert to use hwmon_device_register_with_groups
hwmon: (lm90) Create all sysfs groups in one call
hwmon: (lm90) Always use the dev variable in the probe function
hwmon: (lm90) Create most optional attributes with sysfs_create_group
hwmon: Avoid initializing the same field twice
hwmon: (pc87360) Avoid initializing the same field twice
hwmon: (lm80) Convert to use devm_hwmon_device_register_with_groups
hwmon: (adm1021) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm63) Avoid initializing the same field twice
hwmon: (lm63) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm63) Create all sysfs groups in one call
hwmon: (lm63) Introduce 'dev' variable to point to client->dev
hwmon: (lm63) Add additional sysfs group for temp2_type attribute
hwmon: (f71805f) Fix author's address
Add support for the IT8623E found on Asus motherboards. It has same
hardware monitoring block as IT8603E.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Adding new PCI ID to support AMD F16 M30h processor (Mullins).
While at it, modify Kconfig and Doc files to reflect the
support for newer processors
Note: PCI ID for this processor will make it into pci_ids.h
as part of this patch:
http://marc.info/?l=linux-kernel&m=139291362126057&w=2
which should be pulled into 3.15 when merge window opens
(It currently sits in 'for-next' branch of bp.git-
https://git.kernel.org/cgit/linux/kernel/git/bp/bp.git/log/?h=for-next)
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip's programming interface is quite similar to LTC3880
and supports the same set of sensors.
Reviewed-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hysteresis register is shared among both temperature sensors.
This means changing one also affects the other. To avoid confusion,
established way to express this is to make only the first instance writable
and keep all other instances as read-only. Otherwise users may be
confused that changing the second writable value also affects the first,
while it is more obvious that a writable value may affect a different
read-only value.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
ADC128D818 is a System Monitor with Temperature Sensor. It is similar to LM80
and LM96080, but has 16 bit wide sensor registers and no fan speed monitoring.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC4260 is a Positive Voltage Hot Swap Controller.
The driver currently only supports voltage monitoring, not voltage control.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for IT8603E.
This closes bug #57861:
https://bugzilla.kernel.org/show_bug.cgi?id=57861
[JD: Fixes and clean-ups.]
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull hwmon fixes and updates from Jean Delvare:
"All lm90 driver fixes and improvements"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation: dt: hwmon: Add OF document for LM90
hwmon: (lm90) Add power control
hwmon: (lm90) Add support for TI TMP451
hwmon: (lm90) Use enums for the indexes of temp8 and temp11
hwmon: (lm90) Add support to handle IRQ
hwmon: (lm90) Define status bits
hwmon: (lm90) Fix max6696 alarm handling
TI TMP451 is mostly compatible with ADT7461, except for
local temperature low byte and max conversion rate.
Add support to the LM90 driver.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull hwmon fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (emc6w201) Do not declare enum variable
hwmon: (w83792d) Update module author
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
w83792d was written by me in 2004, I'd like to update my first name
into my current one to keep consistent, and delete invalid address.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The temperature reporting interface stays the same, so we just
add the PCI-ID to the list.
Verified on AMD Olive Hill.
Signed-off-by: Wei Hu <wei@aristanetworks.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Corrected the word adventerous to adventurous.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for ads1115 device to ads1015 driver.
Based on work of Emiliano Carnati <carnatiatebneuro.com>.
Tested on ARM CPU based board.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for DS1631, DS1721, and DS1731 to ds1621 driver
Remove detect function from ds1621 driver as unreliable
Bug fixes in nct6775, iio_hwmon, and adm1021 drivers
Remove redundant platform_set_drvdata in various drivers
Add device tree support to ina2xx driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=OdGw
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver to support GMT G762/G763 pwm fan controllers
- add support for DS1631, DS1721, and DS1731 to ds1621 driver
- remove detect function from ds1621 driver as unreliable
- bug fixes in nct6775, iio_hwmon, and adm1021 drivers
- remove redundant platform_set_drvdata in various drivers
- add device tree support to ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ds1621) Fix temperature rounding operations
hwmon: (nct6775) Drop unsupported fan alarm attributes for NCT6775
hwmon: (nct6775) Fix temperature alarm attributes
Add support for GMT G762/G763 PWM fan controllers
hwmon: (ina2xx) Add device tree support to pass the shunt resistor
hwmon: (ds1621) Update documentation
hwmon: (ds1621) Add DS1731 chip support to ds1621 driver
hwmon: (iio_hwmon) add alias table
hwmon: (adm1021) Do not create min sysfs attributes for LM84
hwmon: (ds1621) Remove detect function
hwmon: (ds1621) Add ds1631 chip support to ds1621 driver and documentation
hwmon: (ds1621) Add ds1721 update interval sysfs attribute
hwmon: (ds1621) Add ds1721 chip support
hwmon: (w83627ehf) Remove redundant platform_set_drvdata()
hwmon: (ntc_thermistor) Remove redundant platform_set_drvdata()
hwmon: (i5k_amb) Remove redundant platform_set_drvdata()
hwmon: (coretemp) Remove redundant platform_set_drvdata()
hwmon: (abituguru3) Remove redundant platform_set_drvdata()
GMT G762/763 fan speed PWM controller is connected directly to a fan
and performs closed-loop or open-loop control of the fan speed. Two
modes - PWM or DC - are supported by the chip. Introduced driver
provides various knobs to control the operations of the chip (via
sysfs interface). Specific characteristics of the system can be passed
either using board init code or via DT. Documentation for both the
driver and DT bindings are also provided.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding another way that is device tree to pass the shunt resistor
value to driver except for platform data.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[Guenter Roeck: Added missing of.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace some written information with tables to improve readability
and to simplify adding newer devices in the future.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These changes add DS1731 chip support to the ds1621 driver,
Kconfig, and documentation.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Due to a lack of device and vendor identification registers, the
Dallas/Maxim DS16xx devices cannot be uniquely detected, sometimes
resulting in false positives. Therefore, the detect function is
being removed in favor of explicit device instantiation.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add definitions, information, and code for ds1631 chip support
to the ds1621 driver.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ds1721 device can be configured for 9..12 bit resolutions;
add a sysfs attribute for userspace to configure this attribute.
The definition, description, details, and usage are shown in the
documentation and were crafted from an LM73 driver patch done by
Chris Verges & Guenter Roeck).
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update the ds1621 documentation, driver, and Kconfig with
ds1721 chip support.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ever since commit 45f035ab9b ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off. Remove all the remaining references to it.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Basically it's the same as the original DS75 but much faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Most LM75-compatible chips can either sample much faster or with a
much better resolution than the original LM75 chip. So far the lm75
driver did not let the user take benefit of these improvements. Do it
now.
I decided to almost always configure the chip to use the best
resolution possible, which also means the longest sample time. The
only chips for which I didn't are the DS75, DS1775 and STDS75, because
they are really too slow in 12-bit mode (1.2 to 1.5 second worst case)
so I went for 11-bit mode as a more reasonable tradeoff. This choice is
dictated by the fact that the hwmon subsystem is meant for system
monitoring, it has never been supposed to be ultra-fast, and as a
matter of fact we do cache the sampled values in almost all drivers.
If anyone isn't pleased with these default settings, they can always
introduce a platform data structure or DT support for the lm75. That
being said, it seems nobody ever complained that the driver wouldn't
refresh the value faster than every 1.5 second, and the change made
it faster for all chips even in 12-bit mode, so I don't expect any
complaint.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
- OpenFirmware/DeviceTree support for the Power Supply core: the core now
automatically populates supplied_from hierarchy from the device tree.
With these patches chargers and batteries can now lookup each other
without the board files support shim. Rhyland Klein at NVIDIA did the
work;
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using the
AB85xx core and depends on some recent changes to it, so that is why the
driver comes through the battery tree. It has an appropriate ack from
the hwmon maintainer (i.e. Guenter Roeck). Martin Persson at ST-Ericsson
and Hongbo Zhang at Linaro authored the driver;
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The changes
touch mfd parts, but these were acked by the appropriate MFD maintainer
(i.e. Samuel Ortiz). Lee Jones at Linaro did most of the work and lead
the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones;
- Versatile Express poweroff driver moved into drivers/power/reset/.
- Tree-wise: use devm_kzalloc() where appropriate;
- Tree-wise: dev_pm_ops cleanups/fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=5BdE
-----END PGP SIGNATURE-----
Merge tag 'for-v3.10' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Highlights:
- OpenFirmware/DeviceTree support for the Power Supply core: the core
now automatically populates supplied_from hierarchy from the device
tree. With these patches chargers and batteries can now lookup
each other without the board files support shim. Rhyland Klein at
NVIDIA did the work
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using
the AB85xx core and depends on some recent changes to it, so that
is why the driver comes through the battery tree. It has an
appropriate ack from the hwmon maintainer (i.e. Guenter Roeck).
Martin Persson at ST-Ericsson and Hongbo Zhang at Linaro authored
the driver
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The
changes touch mfd parts, but these were acked by the appropriate
MFD maintainer (ie Samuel Ortiz). Lee Jones at Linaro did most of
the work and lead the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones
- Versatile Express poweroff driver moved into drivers/power/reset/
- Tree-wide: use devm_kzalloc() where appropriate
- Tree-wide: dev_pm_ops cleanups/fixes"
* tag 'for-v3.10' of git://git.infradead.org/battery-2.6: (112 commits)
pm2301-charger: Fix suspend/resume
charger-manager: Use kmemdup instead of kzalloc + memcpy
power_supply: Populate supplied_from hierarchy from the device tree
power_supply: Add core support for supplied_from
power_supply: Define Binding for power-supplies
rx51_battery: Fix reporting temperature
hwmon: Add ST-Ericsson ABX500 hwmon driver
ab8500_bmdata: Export abx500_res_to_temp tables for hwmon
ab8500_{bmdata,fg}: Add const attributes to some data arrays
ab8500_bmdata: Eliminate CamelCase warning of some variables
ab8500_btemp: Make ab8500_btemp_get* interfaces public
goldfish_battery: Use resource_size()
lp8788-charger: Use PAGE_SIZE for the sysfs read operation
max8925_power: Use devm_kzalloc()
da9030_battery: Use devm_kzalloc()
da9052-battery: Use devm_kzalloc()
ds2760_battery: Use devm_kzalloc()
ds2780_battery: Use devm_kzalloc()
gpio-charger: Use devm_kzalloc()
isp1704_charger: Use devm_kzalloc()
...
TMP432 is similar to TMP431 with a second external temperature sensor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Each of ST-Ericsson X500 chip set series consists of both ABX500 and DBX500
chips. This is ABX500 hwmon driver, where the abx500.c is a common layer for
all ABX500s, and the ab8500.c is specific for AB8500 chip. Under this designed
structure, other chip specific files can be added simply using the same common
layer abx500.c.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
NCT6775, NCT6776, and NCT6779 have a number of variants with the same
chip ID but different chip labels. Add text "or compatible" to the
message displayed when the driver is loaded and rephrase the Kconfig
entry to reflect that it also supports compatible chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP431 is compatible to TMP401.
Also add support for additional I2C addresses supported by TMP411B
and TMP411C.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
So far the driver reported the voltage on VAUX as "vout2". This was not
entirely appropriate as it is not an output voltage, and complicates
the code. Use the new virtual "VMON" register set and report the voltage
as "vmon" instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some sysfs attributes are only supported on LTC2978 and not on LTC3880.
Update documentation to reflect which attributes are supported for which chips.
Output current attributes supported on LTC3880 were described as providing
input current values. Fix text to reflect that the attributes provide output
current values.
"reset history" attribute descriptions were misleading and seemed to imply
that all history was reset when writing a single attribute. Replace with more
accurate text.
Replace 'internal temperature" with "chip temperature". Temperature limits
not only apply to the chip temperature, but also to external temperatures
on LTC3880, so remove the word "chip" from the attribute description.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT677X series support weighted fan control. In this mode, a secondary
temperature source is used in addition to the primary temperature source to
control fan speed. Add support for this feature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver will replace the w83627ehf driver for NCT6775F and NCT6776F,
and provides support for NCT6779D.
This patch provides support for voltage monitor attributes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7310/adt7320 is the SPI version of the adt7410/adt7420. The register map
layout is a bit different, i.e. the register addresses differ between the two
variants, but the bit layouts of the individual registers are identical. So both
chip variants can easily be supported by the same driver. The issue of non
matching register address layouts is solved by a simple look-up table which
translates the I2C addresses to the SPI addresses.
The patch moves the bulk of the adt7410 driver to a common module that will be
shared by the adt7410 and adt7310 drivers. This common module implements the
driver logic and uses a set of virtual functions to perform IO access. The
adt7410 and adt7310 driver modules provide proper implementations of these IO
accessor functions for I2C respective SPI.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7410 driver supports the ADT7420, but its documentation file
makes no mention of that. Add this refrence, and a brief a description
of the differences between the ADT7410 and the ADT7420.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Links to datasheets are no longer valid. Provide links to product information
instead (which provides links to the datasheets and is hopefully more
persistent).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Most of the hwmon driver documentation still listed my old invalid e-mail
address. Fix it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
MAX34460 is a PMBus 12-Channel Voltage Monitor & Sequencer.
MAX34461 is a PMBus 16-Channel Voltage Monitor & Sequencer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the ZL6100 compatible chips support monitoring a separate voltage pin,
VMON (ZL2004) or VDRV (ZL91xx). Report it as in2 / vmon.
The chips support implicit warning limits for VMON/VDRV, as percentage of the
respective critical voltage. Support by reading/writing the critical voltages
and calculating the associated warning voltages.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the TI / Burr-Brown INA209 voltage / current / power
monitor.
Cc: Paul Hays <haysp@magma.net>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for temp1_min_alarm and temp1_max_alarm
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup; dropped platform data and interrupt support]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LM73 supports four A/D conversion resolutions. The default used by
the existing lm73 driver is the chip's default, 11-bit (0.25 C/LSB).
This patch enables changing of this resolution from userspace via the
update_interval sysfs attribute. Full details on usage are included in
Documentation/hwmon/lm73.
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Assume that IT8771E and IT8772E are fully compatible with IT8728F.
IT8771E support contributed by Kelly Anderson.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Add support for MAX6581, MAX6602, MAX6622, MAX6636, MAX6689, MAX6693,
MAX6694, MAX6697, MAX6698, and MAX6699 temperature sensors
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
SENSORS_LIMIT and clamp_val have the same functionality, so retire SENSORS_LIMIT
as it is no longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
IT8721 and IT8728 support Intel PECI temperature reporting. Each sensor
can be programmed to display the temperature reported on the PECI interface.
If configured for Intel PECI, the driver reported the wrong sensor type for
the respective thermal sensor. Fix the code to correctly report it as
"Intel PECI (6)".
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
This is the HWMON patch for DA9055 PMIC and has got dependency on the
DA9055 MFD core.
This patch monitors the DA9055 PMIC's ADC channels vddout, junction temperature
and auxiliary channels.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: Dropped __devinit, __devexit, __devexit_p]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Signed-off-by: Guillaume Roguez <guillaume.roguez@savoirfairelinux.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As there is no reliable way to identify the chip, it is preferable to
remove the detect callback, to avoid misdetection.
Module parameters are not worth it here, so let's get rid of them and
add an ads7828_platform_data structure instead.
Clean the code by removing unused macros, fixing coding style issues,
avoiding function prototypes and using convenient macros such as
module_i2c_driver().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon framework driver for Versatile Express sensors, providing
information about board level voltage (only when regulator driver
is not configured), currents, temperature and power/energy usage.
Labels for the values can be defined as DT properties.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
TjMax for the CE4100 series of Atom CPUs was previously reported to be
110 degrees C.
cpuinfo logs on the web show existing CPU types CE4110, CE4150, and CE4170,
reported as "model name : Intel(R) Atom(TM) CPU CE41{1|5|7}0 @ 1.{2|6}0GHz"
with model 28 (0x1c) and stepping 10 (0x0a). Add the three known variants
to the tjmax table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
cc: stable@vger.kernel.org
Acked-by: Jean Delvare <khali@linux-fr.org>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Jean Delvare <khali@linux-fr.org>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Rob Landley <rob@landley.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull ACPI & Thermal updates from Len Brown:
"The generic Linux thermal layer is gaining some new capabilities
(generic cooling via cpufreq) and some new customers (ARM).
Also, an ACPI EC bug fix plus a regression fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (30 commits)
tools/power/acpi/acpidump: remove duplicated include from acpidump.c
ACPI idle, CPU hotplug: Fix NULL pointer dereference during hotplug
cpuidle / ACPI: fix potential NULL pointer dereference
ACPI: EC: Add a quirk for CLEVO M720T/M730T laptop
ACPI: EC: Make the GPE storm threshold a module parameter
thermal: Exynos: Fix NULL pointer dereference in exynos_unregister_thermal()
Thermal: Fix bug on cpu_cooling, cooling device's id conflict problem.
thermal: exynos: Use devm_* functions
ARM: exynos: add thermal sensor driver platform data support
thermal: exynos: register the tmu sensor with the kernel thermal layer
thermal: exynos5: add exynos5250 thermal sensor driver support
hwmon: exynos4: move thermal sensor driver to driver/thermal directory
thermal: add generic cpufreq cooling implementation
Fix a build error.
thermal: Fix potential NULL pointer accesses
thermal: add Renesas R-Car thermal sensor support
thermal: fix potential out-of-bounds memory access
Thermal: Introduce locking for cdev.thermal_instances list.
Thermal: Unify the code for both active and passive cooling
Thermal: Introduce simple arbitrator for setting device cooling state
...
Conflicts:
drivers/staging/omap-thermal/omap-thermal-common.
OMAP supplied dummy TC1 and TC2,
at the same time that the thermal tree removed them
from thermal_zone_device_register()
drivers/thermal/cpu_cooling.c b/drivers/thermal/cpu_cooling.c
propogate the upstream MAX_IDR_LEVEL re-name
to prevent a build failure
Previously-fixed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>
This movement is needed because the hwmon entries and corresponding sysfs
interface is a duplicate of utilities already provided by
driver/thermal/thermal_sys.c. The goal is to place it in thermal folder
and add necessary functions to use the in-kernel thermal interfaces.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This Patch adds support for mcp3221 chip to the
mcp3021 driver.
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
INA220 is register compatible to INA219, and INA230 is register compatible to
INA226, so all we need to do is to add name aliases for those two chips.
Cc: Lothar Felten <l-felten@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Add support for LM74 and LM71 to LM70 driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Removing the 3wire limitation on LM70 as the component also allows
operation on 4wire SPI bus
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX197 is an A/D converter, made by Maxim. This driver currently
supports the MAX197, and MAX199. They are both 8-Channel, Multi-Range,
5V, 12-Bit DAS with 8+4 Bus Interface and Fault Protection.
The available ranges for the MAX197 are {0,-5V} to 5V, and {0,-10V} to
10V, while they are {0,-2V} to 2V, and {0,-4V} to 4V on the MAX199.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch brings basic support for the Analog Devices ADT7410 temperature
sensor. The following functionality has been implemented:
* get current temperature
* get/set minimum, maximum and critical temperature
* get/set hysteresis
* get alarm events for minimum, maximum and critical temperature
All implemented sysfs attributes have been sucessfully tested at temperatures
of 15°C to 40°C.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is a new driver for the Honeywell Humidicon HIH-6130/HIH-6131 humidity sensor.
The driver is based on the existing Sensiron sht21 driver with the necessary changes
to the probe, update_measurements and conversion functions necessary to use the
Honeywell sensors.
There's no difference between the 6130 & 6131 other than the 6131 having an external
condensation filter attached.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
devres functions are the preferred means to allocate resources in hwmon drivers.
Document it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
The DA9052 PMIC provides an Analogue to Digital Converter with 10 bits
resolution and 10 channels.
This patch monitors the DA9052 PMIC's ADC channels mostly for battery
parameters like battery temperature, junction temperature, battery
current etc.
This patch is functionally tested on Samsung SMDKV6410
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: __init --> __devinit for probe function]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document the Atom series D2000 and N2000 (Cedar Trail) as being supported.
List and set TjMax for those series.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Document the new Atom series (Tunnel Creek and Medfield) as being
supported, and list TjMax for the Atom E600 series.
Also enable the Atom tjmax heuristic for these Atom CPU models.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
New driver for INA219 and INA226, added support for IT8782F and IT8783E/F to
it87 driver, plus cleanups in a couple of drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ZX6H
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New driver for INA219 and INA226, added support for IT8782F and
IT8783E/F to it87 driver, plus cleanups in a couple of drivers."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (it87) Make temp3 attribute conditional for IT8782F
hwmon: (it87) Convert to use devm_kzalloc and devm_request_region
hwmon: INA219 and INA226 support
hwmon: (it87) Create voltage attributes only if voltage is enabled
hwmon: (ntc_thermistor) Fix checkpatch warning
hwmon: (ntc_thermistor) Optimize and fix build warning
hwmon: (ntc_thermistor) Return error code from hwmon_device_register
hwmon: (ntc_thermistor) Convert to devm_kzalloc
hwmon: (ad7314) Remove unused defines, and rename OFFSET to SHIFT
acpi_power_meter: clean up code around setup_attrs
acpi_power_meter: drop meter_rw_attrs, use common meter_attrs
acpi_power_meter: remove duplicate code between register_{ro,rw}_attrs
acpi_power_meter: use a {RW,RO}_SENSOR_TEMPLATE macro to clean things up
acpi_power_meter: use the same struct {rw,ro}_sensor_template for both
hwmon: use module_pci_driver
hwmon: (it87) Add support for IT8782F and IT8783E/F
Add support for the Texas Instruments INA219 and INA226 power monitors.
Signed-off-by: Lothar Felten <l-felten@ti.com>
[guenter.roeck@ericsson.com: formatting cleanup; check for smbus word data;
select PGA=8 for INA219]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
The on-chip northbridge's temperature sensor of the upcoming
AMD Trinity CPUs works the same as for the previous CPUs.
Since it has a different PCI-ID, we just add the new one to the list
supported by k10temp.
This allows to use the k10temp driver on those CPUs.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add I2C driver for MCP3021 that is an ADC chip from Microchip.
The MCP3021 is a successive approximation A/D converter (ADC)
with 10-bit resolution.
The driver export the value of Vin to sysfs, the voltage unit is
mV. Through the sysfs interface, lm-sensors tool can also display
Vin voltage.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on a patch by David Jander that mostly did s/mc13783/mc13xxx/ .
Additionally use dev_get_drvdata instead of to_platform_device +
platform_get_drvdata in mc13783_adc_read (spotted by Jean Delvare).
Cc: David Jander <david.jander@protonic.nl>
Signed-off-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
GMT G781 is a ADM1032-compatible temperature sensor chip.
Add support to the LM90 driver.
Cc: Mike Gorchak <lestat@i.com.ua>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
Add support for the watchdog integrated into the SMSC SCH5627 and
SCH5636 superio-s. Since the watchdog is part of the hwmon logical device
and thus shares ioports with it, the watchdog driver is integrated into the
existing hwmon drivers for these.
Note that this version of the watchdog support for sch56xx superio-s
implements the watchdog chardev interface itself, rather then relying on
the recently added watchdog core / watchdog_dev. This is done because
currently some needed functionality is missing from watchdog_dev, as soon
as this functionality is added (which is being discussed on the
linux-watchdog mailinglist), I'll convert this driver over to using
watchdog_dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[guenter.roeck@ericsson.com: Added missing linux/slab.h include]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
We don't really use or need separate device IDs for the various JC42.4 compliant
chips, so remove them and just stick with jc42.
Also update a datasheet references for SE98A, STTS424, and STTS424E02.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
ZL9101M and ZL9117M are compatible to ZL6100. Add support to the zl6100 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
MDT040 is supported by the generic PMBus driver. Add device ID and reference to
datasheet. Also mention Lineage Power device support in Kconfig.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TPS40400 and TPS40422 are supported by the generic PMBus driver.
Add device IDs and data sheet references.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX34440 and compatibles support reporting the lowest measured output voltage.
Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add detection of the National Semiconductor (now Texas Instruments)
LM96080. It is functionally compatible with the LM80 but detection is
completely different.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Intersil reports that all chips supported by the zl6100 driver require
an interval between chip accesses, even ZL2004 and ZL6105 which were thought
to be safe.
Reported-by: Vivek Gani <vgani@intersil.com>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add description of pwm[1-4]_start_output, pwm[1-4]_step_output,
pwm[1-4]_stop_output, and pwm[1-4]_max_output attributes to driver
documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Properly set the source of temp2 for the W83627UHG. Also fix a
comment right before that, and document the W83627UHG as reporting up
to 3 temperatures.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
These are fully compatible with Jedec JC 42.4 as far as I can see.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The temp[1-*]_type attribute reports the temperature sensor type. Sensor type 1
is described as "PII/Celeron Diode", which is quite restrictive; other CPUs
may also have an embedded temperature sensor diode with similar characteristics.
Change description to "CPU embedded diode" to be more generic.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Until we get a datasheet for the IT8728F, treat it as fully compatible
with the IT8721F, as it seems to work reasonably well.
This closes kernel bug #27262.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The LM63 and compatible devices have a lookup table to control the fan
speed automatically. Expose it in sysfs. Values are cached for 5
seconds, independently of the other register values to avoid slowing
down "sensors". We might make the table values writable in the future.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
On the LM64, the tachometer function has a dedicated pin and fan speed
monitoring is always enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
On LM96163, the external temperature sensor type is configurable to
either a thermal diode or a 3904 transistor. The chip reports a wrong
temperature if misconfigured. Add writable attribute to support it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The update interval is configurable on LM63 and compatibles. Add
support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
LM96163 is an enhanced version of LM63 with improved PWM resolution. Add chip
detection code as well as support for improved PWM resolution if the chip is
configured to use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for Ericsson BMR450, BMR451, BMR462, BMR463, and BMR464, which are
based on ZL2005 and ZL2008, to zl6100 driver. Remove BMR450 and BMR451 device
IDs from generic PMBus driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add explicit support for ZL2005. Functionality is almost the same as with other
Zilker Labs / Intersil chips, but limit register detection does not work reliably.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
This is essentially a stripped down version of the W83627DHG. Noticeable
difference is that it is still powered with +5V, as older models, even
though the ADC resolution is 8 mV as newer models have.
Thanks to Ulf Bruman (Saab Group) for doing all the testing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Explain why clones of the LM75 are generally not detected by the
driver, and why this isn't going to change. Also update the
documentation to reflect the list of chip names currently supported by
the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add datasheet reference and device ID for ADT75.
The ADT75, like some other LM75 derivatives, needs to be instantiated
using methods 1, 2, or 4.
For more information see Documentation/i2c/instantiating-devices.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add device IDs and reference to datasheets for Lineage Power DC-DC converters.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
The LTC3880 PMBus command set is comparable to LTC2978. Add support for it
to the LTC2978 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Provide explicit driver for LTC2978 to enable support for minimum and peak
attributes. Remove ltc2978 chip id from generic pmbus driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Driver for AD7314, ADT7301, and ADT7302, ported from IIO.
Currently dropped power down mode support.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
[guenter.roeck@ericsson.com: Added MODULE_DEVICE_TABLE]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Provide more documentation describing PMBus driver functionality and the API
between the PMBus core driver and PMBus chip drivers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
This patch allows to read temperature
from TMU(Thermal Management Unit) of SAMSUNG EXYNOS4 series of SoC.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
ADM1276 is mostly compatible to ADM1275, with added support for input power
measurement. Add support for it to the ADM1275 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
ADM1275 supports a second current limit, which can be configured as either lower
or upper limit. Add support for it and report it as either lower or upper
critical current limit.
Also replace error return code EINVAL for unsupported pages with ENXIO as this
is more appropriate for the observed condition.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
With commit c814a4c7c4, the meaning of tempX_max
was changed. It no longer returns the value of bits 8:15 of
MSR_IA32_TEMPERATURE_TARGET, but instead returns the value of CPU threshold
register T1. tempX_max_hyst was added to reflect the value of temperature
threshold register T0.
As it turns out, T0 and T1 are used on some systems, presumably by the BIOS.
Also, T0 and T1 don't have a well defined meaning. The thresholds may be used
as upper or lower limits, and it is not guaranteed that T0 <= T1. Thus, the new
attribute mapping does not reflect the actual usage of the threshold registers.
Also, register contents are changed during runtime by an entity other than the
hwmon driver, meaning the values cached by the driver do not reflect actual
register contents.
Revert most of c814a4c7c4 to address the problem.
Support for T0 and T1 will be added back in with a separate commit, using new
attribute names.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
On old CPUs (and even some recent Atom CPUs) TjMax can't be read from
the CPU registers, so it is guessed by the driver using a complex
heuristic which isn't reliable. So let users who know their CPU's
TjMax pass it as a module parameter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The chips supported by the max16065 driver should not be accessed using direct
i2ctools commands. Add warning to driver documentation to alert users.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
hwmon: (lm90) Refactor reading of config2 register
hwmon: (lm90) Make SA56004 detection more robust
hwmon: (lm90) Simplify handling of extended local temp register
hwmon: (pmbus) Add client driver for LM25066, LM5064, and LM5066
hwmon: (max34440) Add support for peak attributes
hwmon: (max8688) Add support for peak attributes
hwmon: (max16064) Add support for peak attributes
hwmon: (adm1275) Add support for peak attributes
hwmon: (pmbus) Add support for peak attributes
hwmon: Add new attributes to sysfs ABI
hwmon: (pmbus) Strengthen check for status register existence
hwmon: (pmbus) Add support for virtual pages
hwmon: (pmbus) Support reading and writing of word registers in device specific code
hwmon: (pmbus) Increase attribute name size
hwmon: (pmbus) Add ADP4000, NCP4200 and NCP4208 to list of supported devices
hwmon: (pmbus) Add support for VID output voltage mode
hwmon: (pmbus) Move PMBus drivers to drivers/hwmon/pmbus
hwmon: (coretemp) Add core/pkg threshold support to Coretemp
hwmon: (lm95241) Add support for LM95231
hwmon: LM95245 driver
...
Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and temperature peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and current peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add the following attributes to the sysfs ABI.
in[0-*]_average
in[0-*]_lowest
in[0-*]_highest
in[0-*]_reset_history
in_reset_history
curr[1-*]_average
curr[1-*]_lowest
curr[1-*]_highest
curr[1-*]_reset_history
curr_reset_history
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch adds the core and pkg support to coretemp.
These thresholds can be configured via the sysfs interfaces tempX_max
and tempX_max_hyst. An interrupt is generated when CPU temperature reaches
or crosses above tempX_max OR drops below tempX_max_hyst.
This patch is based on the documentation in IA Manual vol 3A, that can be
downloaded from here:
http://download.intel.com/design/processor/manuals/253668.pdf
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
A hwmon driver for the National Semiconductor LM95245 dual temperature
sensors chip.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for Philips SA56004, an LM86 compatible temperature sensor.
Signed-off-by: Stijn Devriendt <sdevrien@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for NTC Thermistor series. In this release, the
following thermistors are supported: NCP15WB473, NCP18WB473, NCP03WB473,
and NCP15WL333. This driver is based on the datasheet of MURATA.
The driver in the patch does conversion from the raw ADC value
(either voltage or resistence) to temperature. In order to use
voltage values as input, the circuit schematics should be provided
with the platform data. A compensation table for each type of thermistor
is provided for the conversion.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds support for MAX1668 and compatible temperature sensors.
Signed-off-by: David George <david.george@ska.ac.za>
[guenter.roeck@ericsson.com: minor cleanup of probe error path]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Declare myself the maintainer of the lm78 driver. I still have a
running system with one of these chips.
Also count myself as a co-author of the driver. With 34 commits over
6 years, it seems fair.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds a new driver for SMSC SCH5636 Super I/O chips.
The chips include an embedded microcontroller for hardware monitoring
solutions, allowing motherboard manufacturers to create their own
custom hwmon solution based upon the SCH5636.
Currently the sch5636 driver only supports the Fujitsu Theseus SCH5636
based hwmon solution. The sch5636 driver runs a sanity check on
loading to ensure it is dealing with a Fujitsu Theseus and not with
another custom SCH5636 based hwmon solution.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add some CPU series IDs and links to the Fam12h datasheets.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Baldwin <archerseven@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a new driver for the SMSC EMC6W201 hardware monitoring device.
The device is functionally close to the EMC6D100 series, but is
register-incompatible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Harry G McGavran Jr <w5pny@arrl.net>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The MAX6650 has only one fan input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
MAX6650 device detection is unreliable, we got reports of false
positives. We now have many ways to let users instantiate the devices
explicitly, so unreliable detection should be dropped.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This CPU family provides NB register values to gather following
TDP information
* ProcessorPwrWatts: Specifies in Watts the maximum amount of power
the processor can support.
* CurrPwrWatts: Specifies in Watts the current amount of power being
consumed by the processor.
This driver provides
* power1_crit (ProcessorPwrWatts)
* power1_input (CurrPwrWatts)
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
AMDs upcoming CPUs use the same mechanism for the internal
temperature reporting as the Fam10h CPUs, so we just needed to add
the appropriate PCI-ID to the list.
This allows to use the k10temp driver on those CPUs.
While at it change the Kconfig entry to be more generic.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
After the merge of pkgtemp functionality into the coretemp driver,
the pkgtemp driver is no longer necessary. Remove it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch merges the pkgtemp with coretemp driver.
The sysfs interfaces for all cores in the same pkg
are shown under one directory, in hwmon. It also
supports CONFIG_HOTPLUG_CPU. So, the sysfs interfaces
are created when each core comes online and are
removed when it goes offline.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
[guenter.roeck@ericsson.com: Fixed section reference errors]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for Analog Devices ADM1275 Hot-Swap Controller and Digital Power
Monitor
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Hardware monitoring support for TI UCD90120, UCD90124, UCD9090, and UCD90910
Sequencer and System Health Controllers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This patch adds hardware monitoring support for TI UCD9220, UCD9222, UCD9224,
UCD9240, UCD9244, UCD9246, and UCD9248 Digital PWM System Controllers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This patch adds hardware monitoring support for Maxim MAX16065, MAX16066,
MAX16067, MAX16068, MAX16070, and MAX16071 flash-configurable system managers
with nonvolatile fault registers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
The sht15 sensor allows validating exchanges to and from the device
using a crc8 function. An utility function to reverse a byte has also
been added.
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* Add support for:
- Heater.
- End of battery notice.
- Ability not to reload from OTP.
- Low resolution (12bit temp, 8bit humidity).
* Add an utility function to read individual bytes from the device.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* Add a documentation file for the device.
* Respect a bit more the kernel-doc syntax.
* Rename some variables for clarity.
* Use bool type for flags.
* Use an enum for states (actions being done).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
MAX6642 is a SMBus-Compatible Remote/Local Temperature Sensor with
Overtemperature Alarm from Maxim.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Recent Xeon processor thermal sensors are supported by the coretemp
driver and not the adm1021 driver. Only one old generation of Xeon
processors (the first Netburst ones) are supported by the adm1021
driver.
Reported-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The lm90 driver's attribute update interval is configurable.
Reflect this information in the driver documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for ADT7461A and NCT1008 to the lm90 driver.
Both chips have identical functionality and report the same manufacturing ID
and device ID values.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
MAX34440 and MAX34441 have their own driver, thus there should be explicit
documentation instead of mentioning the chips in the generic PMBus driver
documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
MAX16064 has its own driver, thus should have its own documentation instead of
being mentioned in the generic PMBus driver documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
MAX8688 has its own driver, thus should have its own documentation instead of
being mentioned in the generic PMBus driver documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
tempererature may sound interesting, but temperature is still preferred.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
When writing hardware monitoring drivers, there are some common pitfalls which
keep coming up in code reviews. This patch provides a document describing all
those pitfalls and how to avoid them.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the Fintek F81865F. It's essentially compatible with
the F71882FG, but has fewer inputs: 7 voltage, 2 temperature and 2 fan
inputs only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The list of supported devices was not always well documented in all
places. Clarify and list all devices in documentation, Kconfig and
the driver itself.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This driver exposes the sysfs nodes of the TWL4030 MADC module.
All the voltage channel values are expressed in terms of mV. Channel 13
and channel 14 are reserved. There are channels which represent
temperature and current the output is represented by celcius
and mA respectively.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Configuration for ads1015 gain and datarate is possible via
devicetree or platform data.
This is a followup patch to previous ads1015 patches on Jean Delvares
tree.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
SMSC SCH5627 Super I/O chips include complete hardware monitoring
capabilities. They can monitor up to 5 voltages, 4 fans and 8
temperatures.
The hardware monitoring part of the SMSC SCH5627 is accessed by talking
through an embedded microcontroller. An application note describing the
protocol for communicating with the microcontroller is available upon
request. Please mail me if you want a copy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for detection of the National Semiconductor LM75A using the ID
register value.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The lis3lv02d drivers aren't hardware monitoring drivers, so the don't
belong to drivers/hwmon. Move them to drivers/misc, short of a better
home.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Takashi Iwai <tiwai@suse.de>
The hp_accel driver isn't a hardware monitoring driver, so it doesn't
belong to drivers/hwmon. Move it to drivers/platform/x86, assuming HP
doesn't ship non-x86 laptops.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Takashi Iwai <tiwai@suse.de>
Apparently users are interested in this information, so let's provide
it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Note that these 2 are register compatible and report the same superio id,
but they are 2 distinct chips / models!
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Thomas Faber <thfabba@gmx.de>
Tested-by: Alexey Sychev <owl@umail.ru>
Tested-by: Dieter Bloms <dieter@bloms.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Note that this patch also makes 2 changes to the code paths for the f71889fg
to keep the code unified between the 2 (for simplicities sake). Both of these
are harmless for then f71889fg:
1) The first change is to always set the FAN_PROG_SEL bit to 0. This influences
accesses to some banked fan / pwm registers. On the f71889fg no registers
which we use are banked. On the f71889ed however some more fan registers
have been banked including one which we use, by making the FAN_PROG_SEL bit
0, address 0x96 will point to the right register.
2) The second change is to see a FANx_TEMP_SEL value of 0 as pointing to
a PECI / AMDSI value, and thus disable our pwm related sysfs attr.
This is correct for the f71889ed and on the f71889fg 0 is a reserved
value, so we should never see it and if we do, disabling the pwm related
sysfs attr is a sane thing to do.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Thomas Greve <tg42@gmx.net>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds support for NCT6775F and NCT6776F to the w83627ehf driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Ian Dobson <i.dobson@planet-ian.com> (NCT6776F)
Tested-by: Zachary Marzec <zmarzec@gmail.com> (ASUS P8P67 PRO/NCT6776F)
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Add support for 4th temperature sensor on W83677HG-B.
Display temperature labels on W83677HG-B to report temperature sources.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Some fan control chips support a configuration register to set the number of
tachometer pulses per fan revolution. Add an ABI attribute to support this
configuration register.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
LTC4151 is High Voltage I2C Current and Voltage Monitor from Linear
Technology.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
EMC6D103S is similar to EMC6D103, only it does not support registers 62[5:7],
6D[0:7], and 6E[0:7]. Register respective sysfs attributes and update affected
registers for all other chips only.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for hardware monitoring of Lineage Compact Power Line
Power Entry Modules.
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add the PCI ID to support the internal temperature sensor of the
AMD "Llano" and "Brazos" processor families.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org # ca86828: x86, AMD, PCI: Add AMD northbridge PCI device
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
On systems where the temperature sensor is actually used, the BIOS is
likely to have locked the alarm registers. In that case, all writes
through the corresponding sysfs files would be silently ignored.
To prevent this, detect the locks and make the affected sysfs files
read-only.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The documentation lists standard numbers and chip names in excruciating
detail, but that's all it does. To help mere mortals in deciding
whether to enable this driver, mention what this sensor is for and in
which systems it might be found.
Also add a link to the actual JC 42.4 specification.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds basic support for LM94 to the LM93 driver. LM94 specific
sensors and features are not supported.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add support for the 1.5V voltage monitoring input (in7) of the
SMSC SCH5127 chip.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I had to look it up for one user, so we might as well store it in the
driver documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Trivial patch updating my email contact details due to change of
employer, and because I no longer have access to the previously used
domain.
Unfortunately I also no longer have access to any ads7828 hardware, but
am happy to support/maintain the driver if others are able to test
changes.
Signed-off-by: Steve Hardy <shardy@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Driver for Dallas Semiconductor DS620 temperature sensor and thermostat
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The humidity attribute is already supported by the sht15 driver, and another
driver supporting it is about to be added. Make it official.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the IT8721F/IT8758E. These new chips differ from the
older IT87xxF chips in the following ways:
* ADC LSB is 12 mV instead of 16 mV.
* PWM values are 8-bit instead of 7-bit.
There are other minor changes we don't have to care about in the
driver.
Another change is that we will handle internal voltage scaling in the
driver instead of delegating the work to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The ADT7468 supports a high-frequency PWM output mode where all PWM
outputs are driven by a 22.5 kHz clock. Add support for this mode, and
document it, as it may surprise the user that setting one PWM output
frequency also affects the other PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The PCF8591 can't be detected, don't even try. There are plenty of
other means to instantiate i2c devices these days.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
I was wondering if that chip ever existed publicly... Apparently yes,
so add support for it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This driver adds support for Linear Technology LTC4261 I2C Negative
Voltage Hot Swap Controller.
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The attribute reflects an interval, not a rate.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Revert commit 7721fea3d0 ("hwmon:
f71882fg: add support for the Fintek F71808E").
Hans said:
: A second review after I've received a data sheet for this device from
: Fintek has turned up a few bugs.
:
: Unfortunately Giel (nor I) have time to fix this in time for the 2.6.36
: cycle. Therefor I would like to see this patch reverted as not having any
: support for the hwmon function of this superio chip is better then having
: unreliable support.
Cc: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the 6 temperature monitoring channels of the PC87427.
Note that the sensors resolution can vary, and I couldn't find a way
to figure it out, so we might have to compensate in user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add initial support for PWM outputs of the PC87427 Super-I/O chip.
Only mode change and manual fan speed control are supported. Automatic
mode configuration isn't supported, and won't be until at least one
board is known, which makes uses of the PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for W83667HG-B (very similar to the W83667HG).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
SMSC's EMC2103 family of temperature/fan controllers have 1
onboard and up to 3 external temperature sensors, and allow
closed-loop control of one fan. This patch adds support for
them.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fault files are for hardware failures that can be reported. So far
we've seen chips reporting such failures for temperature sensors and
fans, but not for voltages. Remove in[0-*]_fault for now. It can be
added back later if really needed, but I doubt it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add currX_alarm, currX_min_alarm, currX_max_alarm and currX_beep
attributes to the hwmon sysfs API.
currX_min_alarm and currX_max_alarm are already supported by the LTC4215
and LTC4245 drivers. currX_alarm is supported by the LTC4261 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added _lcrit and _crit to voltage attributes.
Added _lcrit to temperature attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for exposing all GPIO pins as analog voltages. Though this is
not an ideal use of the chip, some hardware engineers may decide that the
LTC4245 meets their design requirements when studying the datasheet.
The GPIO pins are sampled in round-robin fashion, meaning that a slow
reader will see stale data. A userspace application can detect this,
because it will get -EAGAIN when reading from a sysfs file which contains
stale data.
Users can choose to use this feature on a per-chip basis by using either
platform data or the OF device tree (where applicable).
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow device probing to recognise the Fintek F71808E.
Sysfs interface:
* Fan/pwm control is the same as for F71889FG
* Temperature and voltage sensor handling is largely the same as for
the F71889FG
- Has one temperature sensor less (doesn't have temp3)
- Misses one voltage sensor (doesn't have V6, thus in6_input refers to
what in7_input refers for F71889FG)
For the purpose of the sysfs interface fxxxx_in_temp_attr[] is split up
such that it can largely be reused.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update coretemp supported CPU TjMax lists and some cleanup work.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver adds support for the monitoring features of the Summit
Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Document for package level thermal hwmon driver.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1280448826-12004-6-git-send-email-fenghua.yu@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
pavel@suse.cz no longer works, replace it with working address.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Read only one of the GPIO pins as an analog voltage. The ADC can be
switched to a different GPIO pin at runtime, but this is not supported.
Previously, this driver would report the analog voltage of the currently
selected GPIO pin as all three GPIO voltages: in9_input, in10_input and
in11_input.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Add support for the hardware monitoring capabilities of the SCH5127
chip to the dme1737 driver.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Fixes from my driver review:
http://lists.lm-sensors.org/pipermail/lm-sensors/2010-March/028051.html
Only the small changes are in there, more important changes will come
later separately as time permits.
* Drop the remnants of the now gone detect function
* The TMP102 has no known compatible chip
* Include the right header files
* Clarify why byte swapping of register values is needed
* Strip resolution info bit from temperature register value
* Set cache lifetime to 1/3 second
* Don't arbitrarily reject limit values; clamp as needed
* Make limit writing unconditional
* Don't check for transaction types the driver doesn't use
* Properly check for error when setting configuration
* Report error on failed probe
* Make the driver load automatically where needed
* Various other minor fixes
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>
Driver for the TI TMP102.
The TI TMP102 is similar to the LM75. It differs from the LM75 by
having a 16-bit conf register and the temp registers have a minimum
resolution of 12 bits; the extended conf register can select 13-bit
resolution (which this driver does) and also change the update rate
(which this driver currently doesn't use).
[JD: Fix tmp102_exit tag, must be __exit, not __init.]
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The update_rate attribute can be used by drivers to let userspace choose
the update rate of the chip, if it is configurable.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM64 appears to be an LM63 with added GPIO lines. Add support for the
hwmon functionality - GPIO can be added at some later stage if someone
has a need for them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix obvious cases of "it's" being used when "its" was meant.
Signed-off-by: Francis Galiegue <fgaliegue@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
adt7473 driver is obsoleted by adt7475 driver. And it is scheduled
to be removed in Feb 2010.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Hwmon driver for Andigilog aSC7621 family monitoring chips.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add basic support for the ADT7411. Reads out all conversion results (via I2C,
SPI yet missing) and allows some on-the-fly configuration. Tested with a
custom board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Before switching to automatic fan control mode, make sure that all the
trip points make sense. Otherwise, the control loop could lead to
weird fan behavior.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the automatic fan speed control interface as
implemented by IT8705F chips up to revision F and IT8712F chips up to
revision G. This implementation fits very well in our standard sysfs
interface.
I implemented the old and not the new interface because the only chip
I have at hand is an old one, and the new interface is more difficult
to map to the standard sysfs interface. Adding support later should be
possible though, if someone with a supported chip is interested.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Unfortunately ITE is no longer publicly providing datasheets for their
IT87xxF series of chips. They may send them on request if you ask
politely.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The IT87xxF chips support beeping on alarm, if properly wired and
configured. There is one control bit for each input type (temperature,
fan, voltage.) Let the user see and change them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested successfully with an ADM1032 chip on its evaluation board. It
should work fine with all other chips as well.
At this point this is more of a proof-of-concept, we don't do anything
terribly useful on SMBus alert: we simply log the event. But this could
later evolve into libsensors signaling so that user-space applications
can take an appropriate action.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
This chips is found on several Zotac Ion ITX boards, amongst others.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: MC Matti <mcmatti17@googlemail.com>
Cc: Manuel Lamotte-Schubert <mls@pronego.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The latest version of the Revision Guide for AMD Family 10h Processors
lists two more processor revisions which may be affected by erratum 319.
Change the blacklisting code to correctly detect those processors, by
implementing AMD's recommended algorithm.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
This adds a driver for the internal temperature sensor of AMD Family 10h
and 11h CPUs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Most of the documentation and comments were written when the driver was
only supporting one type of chip, only via ACPI/HP. Update the info to
the much clearer understanding that we have now.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level. Add control of rate of change of fan output
level. These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority. Add
support for constant fan speed and proportional-response operations modes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ADT7476 has 5 dedicated pins for VID input, and the +12V input can
optionally be used as a 6th VID pin. Add support for VID input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7476 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 5 voltage inputs instead of 2, and VID input
pins.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7490 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 6 voltage inputs instead of 2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
New documentation for the adt7475 driver, based on the adt7473 driver
documentation. It is IMHO much more useful that the previous
documentation which was essentially redundant with sysfs-interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the ADT7473 to the adt7475 driver, and mark the
adt7473 driver for removal. The ADT7473 and ADT7475 chips are almost
the same chip and essentially compatible, so there's no point in
having separate drivers for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
This adds support for the Fintek f71889fg to the f71882fg driver,
many thanks to Gerd v. Egidy for providing (remote) access to a
machine which such an ic.
Note that this bit of the patch:
- val = SENSORS_LIMIT(val, 0, 255);
+
+ if (data->type == f71889fg)
+ val = SENSORS_LIMIT(val, -128, 127);
+ else
+ val = SENSORS_LIMIT(val, 0, 127);
Changes behaviour for already supported models, the new behaviour is correct
as the already supported models have bit 7 of the involved registers fixed at
0, so the previous behaviour which allowed setting temp zone limits > 127
was not correct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This driver provides support for the ADC integrated into the
Freescale MC13783 PMIC.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This module parameter is there to workaround broken BIOS. I'm not even
sure if it was used in the past 5 years, and it gets in the way of
converting the driver to the MFD infrastructure. So tell the users how
they can do the same from user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
The VID input pins can alternatively be used as GPIOs. Make sure we
have at least 4 pins used for VID, otherwise don't bother reading and
exposing VID.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Adam Nielsen <a.nielsen@shikadi.net>
Document the case of hybrid automatic fan speed control
implementations, where trip points are associated to both PWM output
channels and temperature input channels.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Augment the documentation of the hwmon sysfs API to accomodate ACPI power
meters and the current desired behavior of power capping hardware drivers.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no point in implementing a detect callback for the LTC4215
and LTC4245, as these devices can't be detected. It was there solely
to handle "force" module parameters to instantiate devices, but now
we have a better sysfs interface that can do the same.
So we can get rid of the ugly module parameters and the detect
callbacks. This shrinks the binary module sizes by 36% and 46%,
respectively.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (ltc4245) Clear faults at startup
hwmon: (ltc4215) Clear faults at startup
hwmon: (coretemp) Add Lynnfield CPU
hwmon: (coretemp) Add support for Penryn mobile CPUs
hwmon: (coretemp) Fix Atom CPUs support
hwmon: Delete deprecated FSC drivers
hwmon: (adm1031) Add sysfs files for temperature offsets
Add Lynnfield processor support. Lynnfield is a quad-core Nehalem
based microprocessor for Desktop market, which is introduced in
September 2009.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Kent Liu <kent.liu@linux.intel.com>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Following patch adds support for mobile Penryn CPUs. Intel documents this
poorly. I asked the Coretemp author for some help. This is totally untested and
may not work. Please test!
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix Atom CPUs support. Intel documents TjMax at 90 degrees C but
some Atoms may have 125 degrees C (this is undocumented speculation).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy fscpos and fscher drivers have been replaced by the unified
fschmd driver. The transition period is over now, we can delete them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (119 commits)
ACPI: don't pass handle for fixed hardware notifications
ACPI: remove null pointer checks in deferred execution path
ACPI: simplify deferred execution path
acerhdf: additional BIOS versions
acerhdf: convert to dev_pm_ops
acerhdf: fix fan control for AOA150 model
thermal: add missing Kconfig dependency
acpi: switch /proc/acpi/{debug_layer,debug_level} to seq_file
hp-wmi: fix rfkill memory leak on unload
ACPI: remove unnecessary #ifdef CONFIG_DMI
ACPI: linux/acpi.h should not include linux/dmi.h
hwmon driver for ACPI 4.0 power meters
topstar-laptop: add new driver for hotkeys support on Topstar N01
thinkpad_acpi: fix rfkill memory leak on unload
thinkpad-acpi: report brightness events when required
thinkpad-acpi: don't poll by default any of the reserved hotkeys
thinkpad-acpi: Fix procfs hotkey reset command
thinkpad-acpi: deprecate hotkey_bios_mask
thinkpad-acpi: hotkey poll fixes
thinkpad-acpi: be more strict when detecting a ThinkPad
...
Allows users who use an IDE driver for their disk to use hpfall without
having to modify the source. By default /dev/sda is used.
Suggested by Christian Thaeter in http://lkml.org/lkml/2009/3/25/505.
While we're add it, improve error message if opening /dev/freefall fails.
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Christian Thaeter <ct@pipapo.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Improve the example code to be at least useable, as in not causing
harm (as shown below). Code can still be improved further, but this
adds some basic safeguards.
1. hpfall *MUST* mlockall(MCL_CURRENT|MCL_FUTURE); itself!
Since the Program sits and waits most of the time it becomes very likely
swapped out. If it gets woken up when the laptop drops from the table
while it is swapped out it actually triggers harddrive activity!
2. Daemonize hpfall using 'daemon(0,0)' (quick and dirty).
3. Give hpfall realtime priority.
Should give a chance that it has less latency when woken up.
Signed-off-by: Christian Thaeter <ct@pipapo.org>
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch makes hpfall.c conform to kernel coding style.
I have not fixed the C99 // comments on two lines as they
help indicate that those are not actually comments but
incomplete code.
Before:
total: 10 errors, 6 warnings, 101 lines checked
After:
total: 2 errors, 0 warnings, 99 lines checked
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver exposes ACPI 4.0 compliant power meters as hardware monitoring
devices. This second revision of the driver also exports the ACPI string
info as sysfs attributes, a list of the devices that the meter measures,
and will send ACPI notifications over the ACPI netlink socket. This
latest revision only enables the power capping controls if it can be
confirmed that the power cap can be enforced by the hardware and explains
how the notification interfaces work.
[akpm@linux-foundation.org: remove default-y]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This driver adds support for the hardware monitoring features of
the WM831x PMICs to the hwmon API. Monitoring is provided for
the system voltages supported natively by the WM831x, the chip
temperature, the battery temperature and the auxiliary inputs
of the WM831x.
Currently no alarms are supported, though digital comparators on
the WM831x devices would allow these to be provided.
Since the auxiliary and battery temperature input scaling depends
on the system configuration the value is reported as a voltage to
userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Clean up the pcf8591 driver documentation:
* The PCF8591 chip is now an NXP product.
* Fix a sysfs path.
* Fix the name of sysfs attributes.
* And a few other random fixes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Add documentation for the tmp421 driver.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the hwmon part of the Fintek F71858FG superio IC to the
f71882fg driver. Many thanks to Jelle de Jong for lending me a motherboard
with this superio on it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the new incarnation of the Winbond/Nuvoton W83627DHG
chip known as W83627DHG-P. It is basically the same as the original
W83627DHG with an additional automatic can speed control mode (not
supported by the driver yet.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Madhu <madhu.chinakonda@gmail.com>
Documentation for the tmp401 driver.
The documentation describes the tmp401 driver and the supported Texas
Instruments TMP401 and TMP411 temperature sensor chips.
Further documentation for new sysfs attributes supported by this
driver is added to Documentation/hwmon/sysfs-interface.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Thomas Lorblanches