tps6586x RTC IRQ is nested threaded and wired to the tps6586x inerrupt
controller. So, this flag is not required for nested irqs anymore,
since commit 3c646f2c6a ("genirq: Don't suspend nested_thread irqs
over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Palams RTC IRQ is nested threaded and wired to the Palmas inerrupt
controller. So, this flag is not required for nested irqs anymore,
since commit 3c646f2c6a ("genirq: Don't suspend nested_thread irqs
over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC entries are mostly grouped by vendor. Move the few outliers in
place.
Also, change the one occurrence of 'nxp' to 'NXP' to make all NXP
entries consistent.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver adds support for the PIC32 real time clock and calendar
peripheral:
- reading and setting time
- alarms provided by dedicated IRQ
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The alarm for rx8025 only has a minute accuracy, so unsupport UIE mode.
pcf8563 and hym8563 also have a minute accuracy and unsupport it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The alarm for rx8025 only has a minute accuracy, so round up to nearest
minute when setting alarm. Without doing this, rtctest blocks one day
after setting alarm to 5 seconds later.
pcf8563 and hym8563 also have similar handling.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ctrl1 register is accessed by alarm operations. But it is updated
in threaded interrupt handler without acquiring rtc->ops_lock.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When IRQ line for this chips is connected, devm_request_threaded_irq()
refuses to register irq handler with the following message.
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Few functions were marked inline even though they were relatively large
and sometimes used in multiple places. De-inline them to let the
compiler decide whether optimization makes sense. This fixes inline_hunt
report:
drivers/rtc/rtc-s5m.c: Deinline s5m8767_rtc_set_alarm_reg, save 704 bytes
drivers/rtc/rtc-s5m.c: Deinline s5m8767_wait_for_udr_update, save 192 bytes
Reported-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Makefile/Kconfig currently controlling compilation of this code is:
obj-$(CONFIG_RTC_CLASS) += rtc-core.o
rtc-core-y := class.o interface.o
drivers/rtc/Kconfig:menuconfig RTC_CLASS
drivers/rtc/Kconfig: bool "Real Time Clock"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the code there is no doubt it is builtin-only.
We don't replace module.h with init.h since the file does need
to know what a struct module is.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When setting a new time/date the RTC's clock must be stopped first, in
order to write the time/date registers in an atomic manner.
So, this change stops the clock first and then writes the time/date
registers and the clock control register (to re-enable the clock) in one
turn.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Check if the RTC signals an invalid time/date (due to a battery power loss
for example). In this case ignore the time/date until it is really set again.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
By using i2c_smbus_read_i2c_block_data() the code is now much simpler.
While at it: when reading the RTC's seconds register, all time/date registers
are frozen until the RTC's year register is read. So it is important to read
all time/date registers in one turn to not lose a second event. Make it more
clear why the read must happen in this way.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2123 has an offset register, which can be used to make minor
adjustments to the clock rate to compensate for temperature or
a crystal that is not exactly right.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
clock offset may be set and read in decimal parts per billion
attribute is /sys/class/rtc/rtcN/offset
The attribute is only visible for rtcs that have set_offset implemented.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
A number of rtc devices, such as the NXP pcf2123 include a facility
to adjust the clock in order to compensate for temperature or a
crystal, capacitor, etc, that results in the rtc clock not running
at exactly 32.768 kHz.
Data sheets I have seen refer to this as a clock offset, and measure it
in parts per million, however they often reference ppm to 2 digits of
precision, which makes integer ppm less than ideal.
We use parts per billion, which more than covers the precision needed
and works nicely within 32 bits
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix a scheduling while atomic issue caused by rv8803_set_time()
holding a spinlock during the call to i2c_smbus_read_byte_data().
Signed-off-by: Oleksij Rempel <fixed-term.Oleksij.Rempel@de.bosch.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for RTC controller found on Alphascale asm9260
SoC.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS3231 has programmable square-wave output signal.
This enables to use this feature as a clock provider of
common clock framework.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To make RTC block of MAX77686/MAX77802 as independent driver,
move the registration of i2c device, regmap for register access
and irq_chip for interrupt support inside the RTC driver.
Removed the same initialisation from MFD driver.
Having this change will allow to reuse this driver for different
PMIC/devices from Maxim Semiconductor if they kept same RTC IP on
different PMIC. Some of examples as PMIC MAX77620, MAX20024 where
same RTC IP used and hence driver for these chips will use this
driver only for RTC support.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Get rid of referring parent device info for register access
all the places by making regmap as part of max77686 rtc
device info. This will also remove the need of storing parent
device info in max77686 rtc device info as this is no more required.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc_regmap should be used to access all RTC registers instead
of parent regmap regardless of what chip or property have it.
This makes the register access uniform and extendible for other
chips.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix following check patch error in rtc-max77686 driver:
- Alignment should match open parenthesis.
- braces {} should be used on all arms of this statement.
- Prefer using the BIT macro
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
At the moment the "sun6i" RTC drivers depends on having two specific
SoC families selected.
The Allwinner A64 SoC has the same RTC, so extend the Kconfig option
to allow inclusion of the driver for all Allwinner SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RX6110 comes in two different variants: SPI and I2C.
This driver only supports the SPI variant.
If the need ever arises to also support the I2C variant, this driver
could easily be refactored to support both cases.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2123 data sheet recommends a software reset when the chip
is first powered on. This change avoids resetting the chip
every time the driver is loaded, which has some negative effects.
There are several registers including a clock rate adjustment that really
should survive a reload of the driver (or reboot).
In addition, stopping and restarting the clock to verify the chip is
there is not a good thing once the time is set.
According to the data sheet, the seconds register has a 1 in
the high bit when the voltage has gotten low. We check for this
condition, as well as whether the time retrieved from the chip is
valid. We reset the rtc only if the time is not reliable and valid.
This is sufficient for checking for the presence of the chip,
as either all zeros or all 0xff will result in an invalid time/date
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Refactor chip reset items into its own function, isolating it from
the rest of the device probe.
Subsequent commits will avoid calling this code.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add new functions pcf2123_write(), and pcf2123_write_reg().
Use named defines for the values being written.
This improves modularity and readability, and reduces lines of code.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Put read operations into a function.
This improves modularity and readability.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add defines for all 16 registers in the pcf2123.
Add defines for useful bits from several registers
I've tried to document all the registers, and
as best as possible, all the special bits they employ
Use BIT() wherever possible in the bit definitions
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In drivers/rtc/rtc-rx8025.c is a broken link that is supposed to
lead to a form allowing users to subscribe to the lm-sensors mailing list.
The link <http://lists.lm-sensors.org/mailman/listinfo/lmsensors> leads
to a page with a 404 error. I believe the link should be replaced
with <lm-sensors@lm-sensors.org>.
Signed-off-by: Leslie Lau <laulinxk@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
DS3231 has the temperature registers with a resolution of 0.25
degree celsius. This enables to get the value through hwmon.
# cat /sys/class/i2c-adapter/i2c-2/2-0068/hwmon/hwmon0/temp1_input
21000
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
For RTC chips with no IRQ directly connected to the SoC, the RTC chip
can be forced as a wakeup source by stating that explicitly in
the device's .dts file using the "wakeup-source" boolean property.
This will guarantee the 'wakealarm' sysfs entry is available on the
device, if supported by the RTC.
With these changes to the driver rtc-ds1307 and the necessary entries
in the .dts file, I get an working ds1337 RTC on the Witty Pi extension
board by UUGear for the Raspberry Pi.
An example for the entry in the .dts file:
rtc: ds1337@68 {
compatible = "dallas,ds1337";
reg = <0x68>;
wakeup-source;
If the "wakeup-source" property is set, do not request an IRQ.
Set also UIE mode to unsupported, to get a working 'hwclock' binary.
Signed-off-by: Michael Lange <linuxstuff@milaw.biz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The mt6397 RTC driver can be built either when the MFD_MT6397 driver
is enabled (which selects IRQ_DOMAIN), or when compile testing.
The latter however fails without IRQ domains:
drivers/rtc/rtc-mt6397.c: In function 'mtk_rtc_probe':
drivers/rtc/rtc-mt6397.c:326:13: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
rtc->irq = irq_create_mapping(mt6397_chip->irq_domain, res->start);
This adds an explicit dependency for the COMPILE_TEST case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rv8803 has its own driver that should be used. Remove its id from
the rx8025 driver.
Fixes: b1f9d790b5
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
For better readability, use to_spi_device() and kobj_to_dev() instead
of container_of().
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cleanup of entire driver of its dmesg output:
1. Remove printing of the function name, because printing device name is
sufficient. This also makes the dev_err()-like functions more compact
and readable (not need of line break).
2. Lower from info to debug printing of each RTC interrupt (no need to
make noise on each alarm).
3. Remove dev_info() at beginning of probe because a message is already
always printed by either probe failure or from registering the RTC
device as /dev/rtcX.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The max77686 RTC driver now supports the max77802 RTC as
well so there's no need to have a separate driver anymore.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The regmap_irq_get_virq() can return 0 or -EINVAL in error conditions
but driver checked only for value of 0.
This could lead to a cast of -EINVAL to an unsigned int used as a
interrupt number for devm_request_threaded_irq(). Although this is not
yet fatal (devm_request_threaded_irq() will just fail with -EINVAL) but
might be a misleading when diagnosing errors.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 6f1c1e71d9 ("mfd: max77686: Convert to use regmap_irq")
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The max77686 RTC only supports a range of 99 years so instead of using
year 1900 as the base, the year 2000 is used. This means that 1900 to
1999 are unsupported years.
The driver was printing a warning for those values but was returning a
error so for consistency, print an error message instead and don't say
that a year 2000 is assumed, since the year is not set.
Also, it is better to use dev_* log functions instead of pr_* to print
information about the device in the kernel log in a standardized way.
This also allows to remove the local pr_fmt() defined macro.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The MAX77686 and MAX77802 RTC IP blocks are very similar with only
these differences:
0) The RTC registers layout and addresses are different.
1) The MAX77686 use 1 bit of the sec/min/hour/etc registers as the
alarm enable while MAX77802 has a separate register for that.
2) The MAX77686 RTCYEAR register valid values range is 0..99 while
for MAX77802 is 0..199.
3) The MAX77686 has a separate I2C address for the RTC registers
while the MAX77802 uses the same I2C address as the PMIC regs.
5) The minimum delay before a RTC update (16 msecs vs 200 usecs).
There are separate drivers for MAX77686 and MAX77802 RTC IP blocks
but the differences are not that big so the driver can be extended
to support both instead of duplicating a lot of code in 2 drivers.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The max77686 driver is generic enough that can be used for other
Maxim RTC IP blocks but these might not have the same registers
layout so instead of accessing the registers directly, add a map
to translate offsets to the real registers addresses for each IP.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver has some hard-coded values such as the minimum delay needed
before a RTC update or the mask used for the sec/min/hour/etc registers.
Use a data structure that contains these values and pass as driver data
using the platform device ID table for each device.
This allows to make the driver's ops callbacks more generic so other RTC
that are similar but don't have the same values can also be supported.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Documentation/timers/timers-howto.txt suggest to use usleep_range()
instead of msleep() for small msec (1ms - 20ms) since msleep() will
often sleep for 20ms for any value in that range.
This is fine in this case since 16ms is the _minimum_ delay required
by max77686 for an RTC update but by using usleep_range() instead of
msleep(), the driver can support other RTC IP blocks with a shorter
minimum delay (i.e: in the range of usecs instead of msecs).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It is better to use the ARRAY_SIZE() macro instead of the array length
to avoid bugs if the array is later changed and the length not updated.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The function is always returning zero even in case of failures since
the ret value was not propagated to the callers. Fix the error path.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
The Microsoft Surface 3 tablet shares interrupt line between RTC and one of SPI
controllers. However, the rtc_cmos driver doesn't allow shared interrupts and
user sees the following warning
genirq: Flags mismatch irq 8. 00000080 (8086228E:02) vs. 00000000 (rtc0)
...
[<ffffffffa004eb01>] pxa2xx_spi_probe+0x151/0x600 [spi_pxa2xx_platform]
Allow RTC driver to use shared interrupts.
Seems we are on the safe side to do just this simple change since
cmos_interrupt() handler checks for the actual hardware status anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ds2404_chip_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Before updating time and alarm the driver must set appropriate mask in
UDR register. For that purpose the driver uses common register
configuration and a lot of exceptions per device in the code. The
exceptions are not obvious, for example except the change in the logic
sometimes the fields are swapped (WUDR and AUDR between S2MPS14 and
S2MPS15). This leads to quite complicated code.
Try to make it more obvious by:
1. Documenting the UDR masks for devices and operations.
2. Adding fields in register configuration structure for each operation
(read time, write time and alarm).
3. Splitting the configuration per S2MPS13, S2MPS14 and S2MPS15 thus
removing exceptions for them.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some devices from S2M/S5M family use different register update masks for
different operations (alarm and register update). Now the driver uses
common register configuration and a lot of exceptions per device in code.
Before eliminating the exceptions and using specific register
configuration for given device, make the auto-cleared mask a separate
field. This is merely a refactoring.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove the 'rtc' prefix from some of the fields in struct
s5m_rtc_reg_config because it is obvious - this is a RTC driver. No
functional changes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The simple_strtoul function is obsolete.
This patch replace it by kstrtoul.
Since kstrtoul is more strict, it permits to filter some invalid input that
simple_strtoul accept. For example:
echo '1022xxx' > /sys/devices/pnp0/00:03/rtc/rtc0/max_user_freq
cat /sys/devices/pnp0/00:03/rtc/rtc0/max_user_freq
1022
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The v3020_chip_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Seiko Epson's RTC RX8900 layout register is compatible with the
RV8803. So let's add its ID in order to reuse the same driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The function can return negative values, so its result should
be assigned to signed variable.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver supports the following functions:
- reading and setting time
- alarms when connected to an IRQ
- reading and clearing the voltage low flags
Datasheet:
http://www.epsondevice.com/docs/qd/en/DownloadServlet?id=ID000956
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs)
and by default it is set to 16, see arch/arm/include/asm/irq.h.
This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.
Fixes a runtime problem:
rtc-lpc32xx 40024000.rtc: Can't get interrupt resource
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Minor issue, fix spelling mistake, happend -> happened
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
...and don't do it wrong.
"not ok or N/A" has length 13. Add the trailing newline, and the
snprintf return value will be 14. However, we lied to snprintf and
told it that only 13 bytes were available. Hence snprintf has only
written "not ok or N/" and a trailing '\0' to the buffer. Next we
continue lying, this time to the upper sysfs layer, claiming that we
wrote 14 meaningful bytes to the buffer. That'll make the upper layer
copy "not ok or N/" plus two nul bytes to user space (one nul byte
from snprintf, the other since sysfs takes care to clear the buffer
before giving it to the ->show method).
In the other cases, the claimed buffer size is closer to sufficient,
but we'll still get a nul byte instead of a newline written to user
space. There's absolutely no reason to try to predict the output
size, and there's plenty of room in the buffer, so just use sprintf.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This makes the generated code slightly smaller.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
driver did
| static void da9063_tm_to_data(struct rtc_time *tm, u8 *data,
| {
| const struct da9063_compatible_rtc_regmap *config = rtc->config;
|
| data[RTC_SEC] &= ~config->rtc_count_sec_mask;
| data[RTC_SEC] |= tm->tm_sec & config->rtc_count_sec_mask;
| ...
| }
| ...
| static int da9063_rtc_set_time(struct device *dev, struct rtc_time *tm)
| {
| ...
| u8 data[RTC_DATA_LEN];
| int ret;
|
| da9063_tm_to_data(tm, data, rtc);
which means that some bits of stack content (in 'data[]') was masked out
and written to the RTC.
Because da9063_tm_to_data() is used only by da9063_rtc_set_time() and
da9063_rtc_set_alarm(), we can write fields directly.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The data_year_param struct is never modified, so lets constify it.
This permit to remove cast since of_device_id is const also.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The variable year must be set as unsigned since it is used with
sunxi_rtc_data_year{.min|.max} and as parameter of is_leap_year() which
wait for unsigned int.
Only tm_year is not unsigned, but it is long.
This patch fix also the format of printing of min/max. (must use %u since
they are unsigned)
The parameter to of sunxi_rtc_setaie() must be set to uint since callers
give always uint data.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver core clears the driver data to NULL after device_release
or on probe failure
Signed-off-by: Nizam Haider <nijamh@cdac.in>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add efi_procfs in efi_rtc_ops to show rtc-efi info in /proc/driver/rtc.
Most of the code comes from efi_rtc_proc_show() in efirtc.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc-proc.c is not built as a module. Thus, rather than dealing with
THIS_MODULE's reference count, we should deal with rtc->owner's
reference count.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When the chip increments the YEAR register and it already holds
bin2bcd(99) it reads as 0 afterwards. With this behaviour the last valid
day (without trickery) that has a representation is 2099-12-31 23:59:59.
So refuse to write later dates.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9063 and DA9062 PMICs.
A problem could occur with the existing RTC driver if:
A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.
i.e.
ret = devm_request_threaded_irq()
comes before
rtc->rtc_dev = devm_rtc_device_register();
In this case, the interrupt can be called before the device has been
registered and the handler can be called immediately. The IRQ handler
da9063_alarm_event() contains the function call
rtc_update_irq(rtc->rtc_dev, 1, RTC_IRQF | RTC_AF);
which in turn tries to access the unavailable rtc->rtc_dev.
The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
get_irq_byname is the last thing to happen.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In A.D. 1582 Pope Gregory XIII found that the existing Julian calendar
insufficiently represented reality, and changed the rules about
calculating leap years to account for this. Similarly, in A.D. 2013
Rockchip hardware engineers found that the new Gregorian calendar still
contained flaws, and that the month of November should be counted up to
31 days instead. Unfortunately it takes a long time for calendar changes
to gain widespread adoption, and just like more than 300 years went by
before the last Protestant nation implemented Greg's proposal, we will
have to wait a while until all religions and operating system kernels
acknowledge the inherent advantages of the Rockchip system. Until then
we need to translate dates read from (and written to) Rockchip hardware
back to the Gregorian format.
This patch works by defining Jan 1st, 2016 as the arbitrary anchor date
on which Rockchip and Gregorian calendars are in sync. From that we can
translate arbitrary later dates back and forth by counting the number
of November/December transitons since the anchor date to determine the
offset between the calendars. We choose this method (rather than trying
to regularly "correct" the date stored in hardware) since it's the only
way to ensure perfect time-keeping even if the system may be shut down
for an unknown number of years. The drawback is that other software
reading the same hardware (e.g. mainboard firmware) must use the same
translation convention (including the same anchor date) to be able to
read and write correct timestamps from/to the RTC.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
GregorianDay() is supposed to calculate the day of the week
(tm->tm_wday) for a given day/month/year. In that calcuation it
indexed into an array called MonthOffset using tm->tm_mon-1. However
tm_mon is zero-based, not one-based, so this is off-by-one. It also
means that every January, GregoiranDay() will access element -1 of
the MonthOffset array.
It also doesn't appear to be a correct algorithm either: see in
contrast kernel/time/timeconv.c's time_to_tm function.
It's been broken forever, which suggests no-one in userland uses
this. It looks like no-one in the kernel uses tm->tm_wday either
(see e.g. drivers/rtc/rtc-ds1305.c:319).
tm->tm_wday is conventionally set to -1 when not available in
hardware so we can simply set it to -1 and drop the function.
(There are over a dozen other drivers in drivers/rtc that do
this.)
Found using UBSAN.
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrew Morton <akpm@linux-foundation.org> # as an example of what UBSan finds.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the actual code, read_alarm() always returns -EINVAL when called
during the RTC device registration. This prevents from retrieving an
already configured alarm in hardware.
This patch fixes the issue by moving the HAS_ALARM bit configuration
(if supported by the hardware) above the rtc_device_register() call.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since commit 3fffd12839 ("i2c: allow specifying
separate wakeup interrupt in device tree") we have
automatic wakeup irq support for i2c devices. That
commit missed the fact that rtc-1307 had its own
wakeup irq handling and ended up introducing a
kernel splat for at least Beagle x15 boards.
Fix that by reverting original commit _and_ passing
correct interrupt names on DTS so i2c-core can
choose correct IRQ as wakeup.
Now that we have automatic wakeirq support, we can
revert the original commit which did it manually.
Fixes the following warning:
[ 10.346582] WARNING: CPU: 1 PID: 263 at linux/drivers/base/power/wakeirq.c:43 dev_pm_attach_wake_irq+0xbc/0xd4()
[ 10.359244] rtc-ds1307 2-006f: wake irq already initialized
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
RTC found in s2mps15 is almost same as one found on s2mps13
with few differences in RTC_UPDATE register fields, like:
1> Bit[4] and Bit[1] are reversed
- On s2mps13
WUDR -> bit[4], AUDR -> bit[1]
- On s2mps15
WUDR -> bit[1], AUDR -> bit[4]
2> In case of s2mps13, for alarm register, need to set both
WDUR and ADUR high, whereas for s2mps15 only set AUDR to high.
3> On s2mps15, WUDR, RUDR and AUDR functions should never be used
at the same time.
This patch add required changes to enable s2mps15 rtc timer.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Core:
- Fix rtctest error path
New drivers:
- Microcrystal RV8803
Subsystem wide cleanups:
- remove misuse of IRQF_NO_SUSPEND flag
Drivers:
- at91rm9200: clear RTC alarm status flag prior to suspending
- davinci: remove incorrect reference to probe function
- ds1307: Fix alarm programming for mcp794xx
- ds1390: trickle charger support, fix ds1390_get_reg
- isl1208: Pass the IRQF_ONESHOT flag
- opal: fix type of token
- pcf2127: fix RTC_READ_VL, remove useless driver version
- pcf85063: return an error when date is invalid
- pcf8563: add CLKOUT to common clock framework
- rx8025: remove unnecessary braces
- s3c: Set year, month, day value for setting alarm
- stmp3xxx: unify register access macros
- License fixes: pcf2127, da9063
- wakeup-source support for isl12057 and opal
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sY2D
-----END PGP SIGNATURE-----
Merge tag 'rtc-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Core:
- Fix rtctest error path
New drivers:
- Microcrystal RV8803
Subsystem wide cleanups:
- remove misuse of IRQF_NO_SUSPEND flag
Drivers:
- at91rm9200: clear RTC alarm status flag prior to suspending
- davinci: remove incorrect reference to probe function
- ds1307: Fix alarm programming for mcp794xx
- ds1390: trickle charger support, fix ds1390_get_reg
- isl1208: Pass the IRQF_ONESHOT flag
- opal: fix type of token
- pcf2127: fix RTC_READ_VL, remove useless driver version
- pcf85063: return an error when date is invalid
- pcf8563: add CLKOUT to common clock framework
- rx8025: remove unnecessary braces
- s3c: Set year, month, day value for setting alarm
- stmp3xxx: unify register access macros
- License fixes: pcf2127, da9063
- wakeup-source support for isl12057 and opal"
* tag 'rtc-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (23 commits)
rtc: Add a driver for Micro Crystal RV8803
rtc: s3c: Set year, month, day value for setting alarm
rtc: ds1307: Fix alarm programming for mcp794xx
rtc: isl12057: enable support for the standard "wakeup-source" property
rtc: opal: enable support for the stardard "wakeup-source" property
rtc: isl1208: Pass the IRQF_ONESHOT flag
rtc: pcf8563: add CLKOUT to common clock framework
rtc: davinci: remove incorrect reference to probe function
rtc: at91rm9200: clear RTC alarm status flag prior to suspending
rtc: pcf2127: remove useless driver version
rtc: pcf2127: fix reading uninitialized value on RTC_READ_VL ioctl
rtc: stmp3xxx: unify register access macros
rtc: da9063: GPL copyright inconsistency fix
rtc: pcf85063: return an error when date is invalid
rtc: rx8025: remove unnecessary braces
rtc: ds1343: remove misuse of IRQF_NO_SUSPEND flag
rtc: ab8500: remove misuse of IRQF_NO_SUSPEND flag
rtc: pl031: remove misuse of IRQF_NO_SUSPEND flag
rtc: opal: fix type of token
rtc: ds1390: Add trickle charger device tree binding
...
This driver supports the following functions:
- reading and settings time
- alarms when connected to an IRQ
- reading and clearing the voltage low flags
- nvram
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch sets year, month, day value for set_alarm function.
The current driver omits to set the values.
This fixes setting wake alarm for dates different than current day.
Without the patch the alarm scheduled for tomorrow would fire today on
chosen time.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.kim@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
[k.kozlowski: Rebase and test the patch, update commit message]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
mcp794xx alarm registers must be written in BCD format. However, the
alarm programming logic neglected this by adding one to the value
after bin2bcd conversion has been already done, writing bad values
to month register in case the alarm being set is in October. In this
case, the alarm month value becomes 0x0a instead of the expected 0x10.
Fix by moving the +1 addition within the bin2bcd call also.
Fixes: 1d1945d261 ("drivers/rtc/rtc-ds1307.c: add alarm support for mcp7941x chips")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Though the isl12057 rtc driver should and will continue to support the
legacy "isil,irq2-can-wakeup-machine" property to enable RTC as the
wakeup source, we need to add support for the new standard property
"wakeup-source".
This patch adds support for "wakeup-source" property in addition to the
existing "isil,irq2-can-wakeup-machine" property.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Though the opal rtc driver should and will continue to support the legacy
"has-tpo" property to enable RTC as the wakeup source, we need to add
support for the new standard property "wakeup-source"
This patch adds support for "wakeup-source" property in addition to the
existing "has-tpo" property.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the clkout output clk to the common clock framework.
Disable the CLKOUT of the RTC after power-up.
After power-up/reset of the RTC, CLKOUT is enabled by default,
with CLKOUT enabled the RTC chip has 2-3 times higher power
consumption.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The davinci rtc driver uses the module_platform_driver_probe()
helper to call the probe function and mark it as __init, but
it also puts a reference into its davinci_rtc_driver function.
This will crash if we ever get a deferred probe and the probe
function is called again after the init section has been removed.
kbuild warns about this:
WARNING: vmlinux.o(.data+0x1aa2b4): Section mismatch in reference from the variable davinci_rtc_driver to the function .init.text:davinci_rtc_probe()
The variable davinci_rtc_driver references
the function __init davinci_rtc_probe()
This patch removes the .probe callback from the platform driver,
which avoids those problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
As said in the SAMA5D2 datasheet, "Prior to instructing the device
to enter ULP mode 1, ... and the internal sources of wake-up must
be cleared."
This patch is to clear the RTC alarm status flag prior to suspending
to avoid the erroneous wake-up activity, as it is often used as
the wake-up source for the ULP mode 1.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
A driver version is only really sensible for oot drivers. Also the
dev_info about having found a chip only signals that allocating the
driver data succeeded and so isn't worth much.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The flag reported on the RTC_READ_VL ioctl is only initialized when the
date is read out. So the voltage low value doesn't represent reality but
the status at the time the date was read (or 0 if the date was not read
yet).
Moreover when userspace requests a value via an ioctl there is no added
benefit to also make a prosa representation of this (and other) values
appear in the kernel log so remove the calls to dev_info and the driver
data members to track their state.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use STMP_OFFSET_REG_(SET|CLR) instead of defining _SET and _CLR for
STMP3XXX_RTC_CTRL and STMP3XXX_RTC_PERSISTENT0 - no functional changes.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix misleading and inconsistent copyright header wording.
Alter the copyright header text and MODULE_LICENSE macro to ensure the
GPL v2 licence description is correctly represented.
It will remove the incorrectly LGPL worded text. Words such as "Library"
from the line "GNU Library General Public License"; and replace the word
"library" with "program" in several other places.
The copyright should match the GPL v2 description as specified in the GNU
license found here: http://www.gnu.org/licenses/gpl-2.0.html
It should also match this copyright text with the correct MODULE_LICENSE
macro text as found in the kernel: include/linux/module.h
In this case "GNU Public License v2 or later" is linked with "GPL".
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Return an error when the date is invalid as the policy should be
implemented there.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The IRQF_NO_SUSPEND flag is used to identify the interrupts that should
be left enabled so as to allow them to work as expected during the
suspend-resume cycle, but doesn't guarantee that it will wake the system
from a suspended state, enable_irq_wake is recommended to be used for
the wakeup.
This patch removes the use of IRQF_NO_SUSPEND flags and uses newly
introduce PM wakeup APIs dev_pm_{set,clear}_wake_irq.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The IRQF_NO_SUSPEND flag is used to identify the interrupts that should
be left enabled so as to allow them to work as expected during the
suspend-resume cycle, but doesn't guarantee that it will wake the system
from a suspended state, enable_irq_wake is recommended to be used for
the wakeup.
This patch removes the use of IRQF_NO_SUSPEND flags and uses newly
introduce PM wakeup APIs dev_pm_{set,clear}_wake_irq.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The IRQF_NO_SUSPEND flag is used to identify the interrupts that should
be left enabled so as to allow them to work as expected during the
suspend-resume cycle, but doesn't guarantee that it will wake the system
from a suspended state, enable_irq_wake is recommended to be used for
the wakeup.
This patch removes the use of IRQF_NO_SUSPEND flags and uses newly
introduce PM wakeup APIs dev_pm_{set,clear}_wake_irq.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The variable can take signed values.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Introduce a device tree binding for specifying the trickle charger
configuration for ds1390.
Signed-off-by: Ivan Grimaldi <grimaldi.ivan@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
spi_write_then_read puts in rx_buf the received data starting from
the first byte of the rx_buf
Signed-off-by: Ivan Grimaldi <grimaldi.ivan@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The header of the pcf2127 driver specifies GPL v2 only as license, so
use "GPL v2" as module license specifier instead of "GPL" as the latter
means "GNU Public License v2 or later".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a sentinel to ab85xx_rtc_ids[] in order to fix the following error:
drivers/rtc/rtc-ab8500: struct platform_device_id is 24 bytes. The last of 2 is:
0x61 0x62 0x38 0x35 0x34 0x30 0x2d 0x72 0x74 0x63 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x8c
FATAL: drivers/rtc/rtc-ab8500: struct platform_device_id is not terminated with a NULL entry!
Reported-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
These platform drivers have a platform device ID table but the module
alias information is not created so module autoloading will not work.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Configure the clock source to external clock if available.
External clock is preferred as it can be ticking during suspend.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc can be clocked by an internal 32K clock. Adding the support
to enable the same.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to datasheet, the S2MPS13X and S2MPS14X should update write
buffer via setting WUDR bit to high after ctrl register is written.
If not, ALARM interrupt of rtc-s5m doesn't happen first time when i use
tools/testing/selftests/timers/rtctest.c test program and hour format is
used to 12 hour mode in Odroid-XU3 board.
One more issue is the RTC doesn't keep time on Odroid-XU3 board when i
turn on board after power off even if RTC battery is connected. It can
be solved as setting WUDR & RUDR bits to high at the same time after
RTC_CTRL register is written. It's same with condition of only writing
ALARM registers, so this is for only S2MPS14 and we should set WUDR &
A_UDR bits to high on S2MPS13.
I can't find any reasonable description about this like fix from
datasheet, but can find similar codes from rtc driver source of
hardkernel kernel and vendor kernel.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: <stable@vger.kernel.org> # v3.16
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for RTC controller found on Xilinx Zynq Ultrascale+ MPSoC
platform.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC month value is 1-indexed, but the kernel assumes it is 0-indexed.
This may result in the RTC not rolling over correctly.
Signed-off-by: Bibek Basu <bbasu@nvidia.com>
Signed-off-by: Felix Janda <felix.janda@posteo.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
SA1100 and PXA differ only in register offsets which are currently
hardcoded in a machine specific header. Some arm64 platforms (PXA1928)
have this RTC block as well (and not the PXA270 variant).
Convert the driver to use ioremap and set the register offsets dynamically.
Since we are touching all the register accesses, convert them all to
readl_relaxed/writel_relaxed.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, the rtc-sa1100 and rtc-pxa drivers co-exist as rtc-pxa has a
superset of functionality. Having 2 drivers sharing the same memory
resource is not allowed by the driver model if resources are properly
declared. This problem was avoided by not adding memory resources to the
SA1100 RTC driver, but that prevents clean-up of the SA1100 driver.
This commit converts the PXA RTC to use the exported SA1100 RTC
functions. Now the sa1100-rtc and pxa-rtc devices are mutually
exclusive, so we must remove the sa1100-rtc from pxa27x and pxa3xx.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rtc-linux@googlegroups.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Factor out the RTC initialization from the platform device specific
parts in order to share the RTC device ops with other drivers.
Specifically, it will be shared with rtc-pxa driver.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If ds3232 work on some platform that is not implementing
irq_set_wake, ds3232 will get a WARNING trace in resume.
So fix ds3232->suspended state to false when irq_set_irq_wake
return error.
WARNING: CPU: 0 PID: 729 at kernel/irq/manage.c:604 irq_set_irq_wake+0x4b/0x8c()
Unbalanced IRQ 201 wake disable
Modules linked in:
CPU: 0 PID: 729 Comm: sh Not tainted 3.12.19-rt30+ #25
[<800107d9>] (unwind_backtrace+0x1/0x88) from [<8000e4ef>] (show_stack+0xb/0xc)
[<8000e4ef>] (show_stack+0xb/0xc) from [<802b5fa9>] (dump_stack+0x4d/0x60)
[<802b5fa9>] (dump_stack+0x4d/0x60) from [<800186dd>] (warn_slowpath_common+0x45/0x64)
[<800186dd>] (warn_slowpath_common+0x45/0x64) from [<80018717>] (warn_slowpath_fmt+0x1b/0x24)
[<80018717>] (warn_slowpath_fmt+0x1b/0x24) from [<8003a8d3>] (irq_set_irq_wake+0x4b/0x8c)
[<8003a8d3>] (irq_set_irq_wake+0x4b/0x8c) from [<80204fcb>] (ds3232_resume+0x2d/0x36)
[<80204fcb>] (ds3232_resume+0x2d/0x36) from [<801954c7>] (dpm_run_callback.isra.13+0xb/0x28)
[<801954c7>] (dpm_run_callback.isra.13+0xb/0x28) from [<80195b1b>] (device_resume+0x7b/0xa2)
[<80195b1b>] (device_resume+0x7b/0xa2) from [<80195f0f>] (dpm_resume+0xbb/0x19c)
[<80195f0f>] (dpm_resume+0xbb/0x19c) from [<801960d9>] (dpm_resume_end+0x9/0x12)
[<801960d9>] (dpm_resume_end+0x9/0x12) from [<80037e1d>] (suspend_devices_and_enter+0x17d/0x1d0)
[<80037e1d>] (suspend_devices_and_enter+0x17d/0x1d0) from [<80037ee1>] (pm_suspend+0x71/0x128)
[<80037ee1>] (pm_suspend+0x71/0x128) from [<80037449>] (state_store+0x6d/0x80)
[<80037449>] (state_store+0x6d/0x80) from [<800af4d5>] (sysfs_write_file+0x9f/0xde)
[<800af4d5>] (sysfs_write_file+0x9f/0xde) from [<8007a437>] (vfs_write+0x7b/0x104)
[<8007a437>] (vfs_write+0x7b/0x104) from [<8007a7f7>] (SyS_write+0x27/0x48)
[<8007a7f7>] (SyS_write+0x27/0x48) from [<8000c121>] (ret_fast_syscall+0x1/0x44)
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It's unnecessary the code that assigns info->rtc_clk to NULL in
s3c_rtc_remove.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It's missed to call clk_unprepare() about info->rtc_src_clk in
s3c_rtc_remove and to call clk_disable_unprepare about info->rtc_clk in
error routine of s3c_rtc_probe.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The clock enable/disable codes for alarm have been removed from
commit 24e1455493 ("drivers/rtc/rtc-s3c.c: delete duplicate clock
control") and the clocks are disabled even if alarm is set, so alarm
interrupt can't happen.
The s3c_rtc_setaie function can be called several times with 'enabled'
argument having same value, so it needs to check whether clocks are
enabled or not.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: <stable@vger.kernel.org> # v4.1
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to the Armada38x functional errata FE-3124064, writing to
the RTC TIME register may fail. As a workaround, after writing to RTC
TIME register, issue a dummy write of 0x0 twice to the RTC Status
register. This is the updated implementation of the Errata that
eliminates the need of the long 100ms delay during the RTC set time
procedure.
[gregory.clement@free-electrons.com]: removed the mutex and use the
spinlock again
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Neta Zur Hershkovits <neta@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Wait for the user to set the time to reset the validity bits. Until then,
the time may be invalid.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rx8025_init_client is modifying ctrl[0] and writing it to RX8025_REG_CTRL2
but ctrl[0] is actually RX8025_REG_CTRL1.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of bailing out, disable alarms and continue when
devm_request_threaded_irq() fails. This allows to still provide some
functionality.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove useless error messages, at that point, the user already knows
something went wrong but will not be able to do anything about it anyway.
It is also highly unlikely that some registers are readable/writable
but not some other ones.
Also, transform rx8025_read_reg to be more resemblant to
i2c_smbus_read_byte_data()
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Stop setting the time to epoch when it is invalid. The proper way to handle
that is to return an error when it is invalid instead of returning an
incorrect value.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The datasheet specifies that transfer mode must be 0 for write and either
0x4 (simplified read) or 0 (standard read). 0x8 is not specified, use
standard mode.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The hardware is only capable of handling dates between 2000 and 2099,
enforce that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It is useless to print a message when probe fails as the user is already
aware that it failed.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use devm_request_threaded_irq() so it is not necessary to call free_irq()
explicitly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver currently emulates the concept of threaded IRQ using a
workqueue, switch to threaded IRQ instead.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Spinlock acquisition/release is moved out of the loop body to get
atomic states of NVRAM reading and writing operations.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
The change enables burst mode of access to SRAM for any read()/write()
operations, it is worth to mention that this may influence on
userspace, for instance prior to the change
read(fd, buf, 1);
read(fd, buf + 1, 1);
and
read(fd, buf, 2);
sequences of syscalls over DS1511's sysfs "nvram" fd led to different
DS1511 state changes and/or buf content, if some userspace applications
are written specifically for DS1511 and exploit this strange
"feature", they may be impacted.
Also the change corrects NVRAM size accessible to userspace from 255
bytes to 256 bytes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller size in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit dca1a4b5ff ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Get and use the slow clock as it is necessary for the at91rm9200 rtc.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
drivers/rtc/rtc-gemini.c:151:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
IS_ERR(_OR_NULL) already contain an 'unlikely' compiler flag and there
is no need to do that again from its callers. Drop it.
gemini driver was using likely() for a failure case while the rtc driver
is getting registered. That looks wrong and it should really be
unlikely. But because we are killing all the unlikely() flags, lets kill
that too.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
See help for clk_get_rate(): "obtain the current clock rate (in Hz) for a
clock source. This is only valid once the clock source has been enabled."
It currently returns the correct value but that may not stay that way.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
rtc->sclk necessarily points to a valid clocks at this point. Else the
probe would have aborted.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In case of a probe error, it is possible to abort after issuing
clk_prepare_enable(). Ensure the clock is disabled and unprepared in that
case.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The email address missed character ">", so add it.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit d5a1c7e3fc ("rtc-cmos: Add an alarm disable quirk") that
added a special quirk is not needed because [PATCH 1/2] of this
patchset makes the kernel more robust:
rtc-cmos: Cancel alarm timer if alarm time is equal to now+1 seconds
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Tested-by: Egbert Eich <eich@suse.de>
Tested-by: Diego Ercolani <diego.ercolani@gmail.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Steps to reproduce the problem:
1) Enable RTC wake-up option in BIOS Setup
2) Issue one of these commands in the OS: "poweroff"
or "shutdown -h now"
3) System will shut down and then reboot automatically
Root-cause of the issue:
1) During the shutdown process, the hwclock utility is used
to save the system clock to hardware clock (RTC).
2) The hwclock utility invokes ioctl() with RTC_UIE_ON. The
kernel configures the RTC alarm for the periodic interrupt
(every 1 second).
3) The hwclock uitlity closes the /dev/rtc0 device, and the
kernel disables the RTC alarm irq (AIE bit of Register B)
via ioctl() with RTC_UIE_OFF. But, the configured alarm
time is the current_time + 1.
4) After the next 1 second is elapsed, the AF (alarm
interrupt flag) of Register C is set.
5) The S5 handler in BIOS is invoked to configure alarm
registers (enable AIE bit and configure alarm date/time).
But, BIOS does not clear the previous interrupt status
during alarm configuration. Therefore, "AF=AIE=1" causes
the rtc device to trigger an interrupt.
6) So, the machine reboots automatically right after shutdown.
This patch cancels the alarm timer if the following condictions are
met (suggested by Alexandre):
1) The configured alarm time is equal to current_time + 1
seconds.
2) The AIE timer is not in use.
The member 'alarm_expires' is introduced in struct cmos_rtc because
of the following reasons:
1) The configured alarm time can be retrieved from
cmos_read_alarm(), but we need to take the 'wrapped
timestamp' and 'time rollover' into consideration. The
function __rtc_read_alarm() eliminates the concerns. To
avoid the duplicated code in the lower level RTC driver,
invoking __rtc_read_alarm from the lower level RTC driver
is not encouraged. Moreover, the compilation error 'the
undefined __rtc_read_alarm" is observed if the lower level
RTC driver is compiled as a kernel module.
2) The uie_rtctimer.node.expires and aie_timer.node.expires can
be retrieved for the configured alarm time. But, the problem
is that either of them might configure the CMOS alarm time.
We cannot make sure UIE timer or AIE tiemr configured the
CMOS alarm time before. (uie_rtctimer or aie_timer is enabled
and then is disabled).
3) The patch introduces the member 'alarm_expires' to keep the
newly configured alarm time, so the above-mentioned concerns
can be eliminated.
The issue goes away after 20-time shutdown tests.
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Tested-by: Egbert Eich <eich@suse.de>
Tested-by: Diego Ercolani <diego.ercolani@gmail.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add DA9062 RTC support into the existing DA9063 RTC driver component by
using generic access tables for common register and bit mask definitions.
The following change will add generic register and bit mask support to the
DA9063 RTC. The changes are slightly complicated by requiring support for
three register sets: DA9063-AD, DA9063-BB and DA9062-AA.
The following alterations have been made to the DA9063 RTC:
- Addition of a da9063_compatible_rtc_regmap structure to hold all generic
registers and bitmasks for this type of RTC component.
- A re-write of struct da9063 to use pointers for regmap and compatible
registers/masks definitions
- Addition of a of_device_id table for DA9063 and DA9062 defaults
- Refactoring functions to use struct da9063_compatible_rtc accesses to
generic registers/masks instead of using defines from registers.h
- Re-work of da9063_rtc_probe() to use of_match_node() and dev_get_regmap()
to provide initialisation of generic registers and masks and access to
regmap
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Implement the suspend/resume function in order to control rtc's irq_wake flag and handle as wakeup source.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of creating wakealarm attribute manually, after the device has been
registered, let's rely on facilities provided by the attribute groups to
control which attributes are visible and which are not. This allows to
create all needed attributes at once, at the same time that we register RTC
class device.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of using older style DEVICE_ATTR for wakealarm attribute let's
switch to using DEVICE_ATTR_RW that ensures consistent across the kernel
permissions on the attribute.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Users of rtc_does_wakealarm() return value treat it as boolean so let's
change the signature accordingly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since commit e6229bec25 ("rtc: make rtc_update_irq callable with irqs
enabled") rtc_update_irq() is callable with irqs enabled.
Signed-off-by: Henri Roosen <henriroosen@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since dab472eb93 ("i2c / ACPI: Use 0 to indicate that device does not
have interrupt assigned"), 0 is not a valid i2c client irq anymore, so
change all driver's checks accordingly.
The same issue occurs when the device is instantiated via device tree
with no IRQ, or from the i2c sysfs interface, even before the patch
above.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
struct rtc embeds both struct dev and struct cdev. Unfortunately character
device structure may outlive the parent rtc structure unless we set it up
as parent of character device so that it will stay pinned until character
device is freed.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Technically the address of rtc->dev can never be NULL, so get_device()
can never fail. Also caller of rtc_device_unregister() supposed to be
the owner of the device and thus have a valid reference. Therefore
call to get_device() is not needed here.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit 59cca865f2 ("drivers/rtc/class.c: fix device_register() error
handling") correctly noted that naked kfree() should not be used after
failed device_register() call, however, while it added the needed
put_device() it forgot to remove the original kfree() causing double-free.
Cc: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The current codes use CSR platform specific API exported by machine
codes to read/write RTC registers. they are:
sirfsoc_rtc_iobrg_readl()
sirfsoc_rtc_iobrg_writel()
commit b1999477ed ("ARM: prima2: move to use REGMAP APIs for rtciobrg")
moves to regmap support, now we can move to use regmap APIs in RTC
driver.
Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc-opal driver provides support for rtc alarms via
timed-power-on(tpo). However some Power platforms like BML use a fake
rtc clock and don't support tpo. Such platforms are indicated by the
missing 'has-tpo' property in the device tree.
Current implementation however enables callback for
rtc_class_ops.read/set alarm irrespective of the tpo support from the
platform. This results in a failed opal call when kernel tries to read
an existing alarms via opal_get_tpo_time during rtc device registration.
This patch fixes this issue by setting opal_rtc_ops.read/set_alarm
callback pointers only when tpo is supported.
Acked-by: Michael Neuling <mikey@neuling.org>
Acked-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add driver for the RTC found on NXP LPC178x/18xx/408x/43xx devices.
The RTC provides calendar and clock functionality together with
alarm interrupt support.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The PCF2127 datasheet states that it's wrong to say that the date in
unreliable if BLF (battery low flag) is set but instead, OSF (seconds
register) should be used to check if oscillator, for any reason, stopped.
Battery may be low (usually below 2V5 threshold) but the date may be anyway
correct (typically date is unreliable when input voltage is below 1V2).
Signed-off-by: Andrea Scian <andrea.scian@dave.eu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There's a wrong comment in some RTC drivers that say it's better to ignore
rtc_valid_tm() when reading RTC timestamp. However this is wrong and is
better to return to the userspace the error if timestamp is not valid.
Signed-off-by: Andrea Scian <andrea.scian@dave.eu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Along with DT support, this patch also cleans up the unnecessary
code around 'rtc_wakeup' initialization.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
removing below static analysis error:
(error) Possible null pointer dereference: client
if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
^^^^^^^
Error comes because client is dereferenced before NULL check.
So probably NULL this check is not required.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use module_platform_driver for drivers whose init and exit functions
only register and unregister, respectively.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@a@
identifier f, x;
@@
-static f(...) { return platform_driver_register(&x); }
@b depends on a@
identifier e, a.x;
@@
-static e(...) { platform_driver_unregister(&x); }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_platform_driver;
@@
-module_exit(e);
+module_platform_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
With the recent pinctrl-single changes, SoCs such as Texas
Instrument's OMAP processors can treat wake-up events from deeper idle
states as interrupts.
Let's add support for the optional second interrupt for wake-up using
the generic wakeirq support added in commit 4990d4fe32 ("PM /
Wakeirq: Add automated device wake IRQ handling")
Finally, to pass the wake-up interrupt in the dts file,
interrupts-extended property needs to be passed.
This is similar in approach to commit 2a0b965cfb ("serial: omap: Add
support for optional wake-up") + ee83bd3b64 ("serial: omap: Switch
wake-up interrupt to generic wakeirq")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It is always a good practice to keep the #includes sorted
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since we are not doing anything fancy in remove function that requires
us to sequence IRQ free operation, we might as well switch over to devm_
equivalent of managed IRQ allocation and remove the explicit free_irq
since it'd be done automatically at remove.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver currently emulates the concept of threaded IRQ using a
workqueue, which it really does not need to. Instead, switch over to
threaded_irq handlers which is meant precisely for the same purpose.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
- Core Frameworks
- New Base API to traverse devices and their children in reverse order
- Bug Fixes
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
- Fix-ups
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2blS
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
Select REGMAP_MMIO to fix the following build error seen with x86_64
randconfig.
drivers/built-in.o: In function `snvs_rtc_probe':
rtc-snvs.c:(.text+0x567730): undefined reference to `devm_regmap_init_mmio_clk'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
With well over 200+ users of this api, there are a mere 12 users that
actually checked the return value of this function. And all of them
really didn't do anything with that information as the system or module
was shutting down no matter what.
So stop pretending like it matters, and just return void from
misc_deregister(). If something goes wrong in the call, you will get a
WARNING splat in the syslog so you know how to fix up your driver.
Other than that, there's nothing that can go wrong.
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Christine Caulfield <ccaulfie@redhat.com>
Cc: David Teigland <teigland@redhat.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device tree support for the mxc rtc driver.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The mxc RTC needs two clocks, one for the input
reference, and one for the IP. But this driver
was only using one clock (for the reference).
This patch add the second clock (for the IP).
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Initial submission adding support for this IP only included Watchdog and
the Real-Time Clock. Now the third (and final) device is enabled this
trivial patch is required to update the comment in the RTC driver to
encompass Clocksource.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the 'flags' variable in order to fix the following warning:
drivers/rtc/rtc-armada38x.c:91:22: warning: unused variable 'flags' [-Wunused-variable]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc_sysfs_add_device checks if device can wakeup before creating the
wakealarm file in sysfs. Thus the driver must set wakeup capability
before registering the rtc device.
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
snvs included rtc, on/off key, power-off module
change to syscon to access register
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Multiple options depend on I2C but are already under under if I2C. Remove
those useless dependencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some entries in the Kconfig are improperly indented with spaces instead of
tabs.
Also fix whitespaces in Makefile.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Gcc is unable to prove that alm_pending is always initialized
when it is used, so it prints a harmless warning:
drivers/rtc/rtc-pcf8563.c: In function 'pcf8563_probe':
drivers/rtc/rtc-pcf8563.c:449:5: warning: 'alm_pending' may be used uninitialized in this function [-Wmaybe-uninitialized]
This uses the same conditional expression that is used inside of
the pcf8563_get_alarm_mode() function, to help gcc figure it out
and shut up that warning, and make the ARM defconfigs build again
with no warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a45d528aab ("rtc: pcf8563: clear expired alarm at boot time")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Alarm interrupt enable register is at offset 0x7, while the time
registers for the alarm follow that. When we program Alarm interrupt
enable prior to programming the time, it is possible that previous
time value could be close or match at the time of alarm enable
resulting in interrupt trigger which is unexpected (and does not match
the time we expect it to trigger).
To prevent this scenario from occuring, program the ALM0_EN bit only
after the alarm time is appropriately programmed.
Ofcourse, I2C programming is non-atomic, so there are loopholes where
the interrupt wont trigger if the time requested is in the past at
the time of programming the ALM0_EN bit. However, we will not have
unexpected interrupts while the time is programmed after the interrupt
are enabled.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Sometimes the irq line is not connected to any soc-pin. This does
not hinder basic timekeeping functionality of the rtc, so probe
should not fail in this case.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use resource_size function on resource object instead of explicit
computation.
No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver can't accommodate the 12 hour mode but the error message states
that the 24 hour mode is not supported.
Also fix the typos (hour vs hours).
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use bit instead of hand coding the shift and correct the 24 hour vs 24
hours typo.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc-efi driver declares that the EFI 'epoch' is 1/1/1998, but
the UEFI spec does not define it at all. It does define a range of
[1900, 9999] for the 'Year' member of the EFI_TIME struct, so let's
use 1900 as the minimum year and not 1998.
Also, move the validation of the year to the convert_from_efi_time()
routine where all other EFI_TIME fields are validated as well.
This prevents rtc_read_time() failures when the RTC that backs the
EFI time services is set to a date before 1998, e.g., when it has
lost power.
This also optimizes the compute_wday() routine, by replacing the for
loop with a simple arithmetic expression, and by reusing the yearday
value that we need to compute anyway when populating the
rtc_time::tm_yday field.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now rtc_set_mmss() has no users, just remove it.
We still have rtc_set_time() doing similar things.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, CONFIG_RTC_SYSTOHC uses CONFIG_RTC_HCTOSYS_DEVICE which
is originally used by CONFIG_RTC_HCTOSYS, but this rtc device has
some limiations, for example, it must be battery-backed, be able
to work with irq off and through system suspension, etc.
So add CONFIG_RTC_SYSTOHC_DEVICE used exclusively for CONFIG_RTC_SYSTOHC,
it is more lenient compared to CONFIG_RTC_HCTOSYS_DEVICE, and could
be assigned any available RTC in the system.
Default value is CONFIG_RTC_HCTOSYS_DEVICE which is "rtc0" by default.
After this patch, NTP will sync up "rtc0" by default.
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
sunxi_rtc_setalarm() uses deprecated rtc_tm_to_time(),
which will overflow in year 2106 on 32-bit machines.
This patch solves this by:
- Replacing rtc_tm_to_time() with rtc_tm_sub()
Also remove the unnecessary initial zeroing of some
local variables in sunxi_rtc_setalarm().
Cc: Carlo Caione <carlo.caione@gmail.com>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
isl1208_i2c_set_alarm() uses deprecated rtc_tm_to_time(),
which will overflow in year 2106 on 32-bit machines.
This patch solves this by:
- Replacing rtc_tm_to_time() with rtc_tm_sub()
Cc: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf8563_rtc_set_alarm() uses deprecated rtc_tm_to_time()
and rtc_time_to_tm(), which will overflow in year 2106
on 32-bit machines.
This patch solves this by:
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
- Replacing rtc_tm_to_time() with rtc_tm_to_time64()
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Initialise the variable high_bb_charging before using it to avoid
configuring wrong value and fix following compilation warning:
/*
rtc-palmas.c: In function ‘palmas_rtc_probe’:
rtc-palmas.c:242:7: warning: ‘high_bb_charging’ may be used
uninitialized in this function
*/
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[viresh.kumar@linaro.org: acked rtc-spear]
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Return -EINVAL if the voltage low bit is set to avoid getting a bogus
time at boot.
There was a comment stating that util-linux hwclock refuses to set a
new time if we return an error code on read, but at least the current
version do set the time as expected. Remove the comment and the check
for valid time, and let the rtc core check it for us.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Driver for the on chip RTC found on Cortina's SoC Gemini.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
[alexandre.belloni@free-electrons.com: use devm_request_irq() and remove
useless goto]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When entering suspend while an wakeup alarm is set, enable_set_wake
should make sure that the RTC interrupt keep being enabled and the
.irq_set_wake for the RTC interrupt get called. However, since the
driver uses the suspend_noirq callback, the call to enable_irq_wake
has been made after disabling the interrupts. While .irq_set_wake
has been called properly, the interrupt remained disabled.
Use the suspend callback to call enable_irq_wake early enough to
ensure the RTC interrupt remains enabled.
Fixes: 7654e9d4fd ("drivers/rtc/rtc-snvs: fix suspend/resume")
Cc: <stable@vger.kernel.org> # 3.19
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Using gpio_request_array()/gpio_free_array() can make the code
simpler because it can set the direction and initial value
in one shot and the for loop is unnecessary.
Also, struct v3020_gpio is removed, because the struct v3020_gpio
is replaced with struct gpio.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Drivers should not be using the __raw_* io accessors.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the rtc-max77802 driver is built as a module, modalias information is
not filled so the module is not autoloaded. Use the MODULE_DEVICE_TABLE()
macro to export the platform ID table so the module contains that data.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the rtc-max77686 driver is built as a module, modalias information is
not filled so the module is not autoloaded. Use the MODULE_DEVICE_TABLE()
macro to export the platform ID table so the module contains that data.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entries will be added to
modules.alias:
alias i2c:ds1672 rtc_ds1672
alias i2c:max6900 rtc_max6900
alias platform:lp3974-rtc rtc_max8998
alias platform:max8998-rtc rtc_max8998
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
On some !ARM 32bits platforms, the following compilation error happens
because of the division on a 64bits value in mtk_rtc_read_time():
drivers/built-in.o: In function `mtk_rtc_read_time':
rtc-mt6397.c:(.text+0x265d13f): undefined reference to `__divdi3'
rtc-mt6397.c:(.text+0x265d150): undefined reference to `__moddi3'
Use div_s64() as done in rtc_time64_to_tm() to solve that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to C99, %2.s means 'print two spaces' (a precision of
. without following digits or * means 0). The kernel's printf
implementation, however, treats that case as if no precision was
given, but relying on that quirk is rather silly. Also, since no -
(aka left-justify) flag is given, the field with of 2 would then cause
the alarm->enabled case to come out as "o n". Deobfuscate it.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch updates the email address of the rtc-at32ap700x driver supported by
me to an email account I will use on a more regular basis in the future.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.
[ralf@linux-mips.org: Resolve a number of simple conflicts.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the DryICE unit is locked it is impossible to set the time. Provide an
error message for this case.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Maybe the unit enters the hardware related state at runtime and not at
system boot time (after a power cycle).
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This code is required to recover the unit from a security violation.
Hopefully this code can recover the unit from a hardware related invalid
state as well.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Be independent of the endianness of the kernel.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are now no differences between RTC on Exynos3250 and S3C6410.
Merge everything into one so duplicated code could be removed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc_timer_cancel() always returns 0 and cannot fail (calls only
other void-returning functions).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
While setting the time, the RTC TIME register should not be accessed.
However due to hardware constraints, setting the RTC time involves
sleeping during 100ms. This sleep was done outside the critical section
protected by the spinlock, so it was possible to read the RTC TIME
register and get an incorrect value. This patch introduces a mutex for
protecting the RTC TIME access, unlike the spinlock it is allowed to
sleep in a critical section protected by a mutex.
The RTC STATUS register can still be used from the interrupt handler but
it has no effect on setting the time.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org> [4.0]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a basic driver for the ultra-low-power Abracon AB x80x series of RTC
chips. It supports in particular, the supersets AB0805 and AB1805.
It allows reading and writing the time, and enables the supercapacitor/
battery charger.
[arnd@arndb.de: abx805 depends on i2c]
[alexandre.belloni@free-electrons.com: renam buffer from date to buf in abx80x_rtc_read_time()]
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ST's Low Power Controller (LPC) controls two devices; watchdog and RTC.
Only one of the devices can be used at any one time. This is enforced
by the correlating MFD driver. This portion of the driver-set controls
the Real Time Clock.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change the __raw IO calls to readl/write_relaxed which makes the driver
endian agnostic to run properly on big endian systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Andrew Victor <linux@maxim.org.za>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC driver supports two flavors of S5M devices: S5M8767-like and
S2MPS14-like.
On S2MPS13 and S2MPS14 devices the RTC module is the same so we want to
re-use the existing support of S2MPS14. However device type was passed
from parent MFD driver in platform data structure. This way for the
S2MPS13 device the main MFD driver passed device type of 'S2MPS13X'.
Instead decouple detecting of device type between main MFD and RTC driver.
This allows adding support for other S2MPS14 variations (like S2MPS11 and
S2MPS13) easily by adding to mfd/sec-core.c:
static const struct mfd_cell s2mps13_devs[] = {
{ .name = "s2mps14-rtc", }
};
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hym8563 datasheet describes the clock output control-bit as "when set
to logic 0, the square wave output is enable, when set to logic 1, the
CLKOUT output is inhibited". But in reality the setting is exactly
opposite.
Before now, the clock output was not really used, but on the rk3288 soc
this generated clock is used to supply the temperature sensor block and
the swapped bit value prevented it from working. With the corrected
value, the tsadc now reports correct values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Grygorii Strashko