The System Timer peripheral provides four 32-bit timer channels and a
single 64-bit free running counter. Each channel has an output compare
register, which is compared against the 32 least significant bits of the
free running counter values, and generates an interrupt.
Timer 3 is used as the Linux timer.
The BCM2835 also contains an SP804-based timer module. However, it
apparently has significant differences from the standard SP804 IP block,
and Broadcom's documentation recommends using the system timer instead.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved to drivers/clocksource/. This looks like the desired location for
such code now.
* Added DT binding docs.
* Moved struct sys_timer bcm2835_timer into time.c to encapsulate it more.
* Simplified bcm2835_time_init() to find one matching node and operate on
it, rather than looping over all matching nodes. This seems more
consistent with other clocksource code.
* Simplified bcm2835_time_init() using of_iomap().
* Renamed struct bcm2835_timer.index to match_mask to better represent its
purpose.
* s/printk(PR_INFO/pr_info(/
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support for the ARM generic timers with A64 instructions
for accessing the timer registers. It uses the physical counter as the
clock source and the virtual counter as sched_clock.
The timer frequency can be specified via DT or read from the CNTFRQ_EL0
register. The physical counter is also accessible from user space
allowing fast gettimeofday() implementation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Modify the SH MTU2 clock event device driver to support runtime PM at
a basic level (i.e. device clocks can be disabled and enabled, but
domain power must be on, because the device has to be marked as
"irq safe").
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Modify the SH CMT clock source/clock event device driver to support
runtime PM at a basic level (i.e. device clocks can be disabled and
enabled, but domain power must be on, because the devices have to
be marked as "irq safe").
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Modify the SH TMU clock source/clock event device driver to support
runtime PM at a basic level (i.e. device clocks can be disabled and
enabled, but domain power must be on, because the devices have to
be marked as "irq safe").
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The syscore device PM flag is used to mark the devices (belonging to
a PM domain) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages. That flag is
stored in the device's struct pm_subsys_data object whose address is
available from struct device. However, in some situations it may be
convenient to set that flag before the device is added to a PM
domain, so it is better to move it directly to the "power" member of
struct device. Then, it can be checked by the routines in
drivers/base/power/runtime.c and drivers/base/power/main.c, which is
more straightforward.
This also reduces the number of dev_gpd_data() invocations in the
generic PM domains framework, so the overhead related to the syscore
flag is slightly smaller.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The always_on device flag is used to mark the devices (belonging to
a PM domain) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages. Change name
of that flag to "syscore" to better reflect its purpose.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Introduce suspend/resume routines for SH MTU2 clock event devices
such that if those devices belong to a PM domain, the generic PM
domains framework will be notified that the given domain may be
turned off (during system suspend) or that it has to be turned on
(during system resume).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Introduce suspend/resume routines for SH CMT clock event devices and
modify the suspend/resume routines for SH CMT clock sources such that
if those devices belong to a PM domain, the generic PM domains
framework will be notified that the given domain may be turned off
(during system suspend) or that it has to be turned on (during system
resume).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Introduce suspend/resume routines for SH TMU clock source and
clock event device such that if those devices belong to a PM domain,
the generic PM domains framework will be notified that the given
domain may be turned off (during system suspend) or that it has to
be turned on (during system resume).
This change allows the A4R domain on SH7372 to be turned off during
system suspend (tested on the Mackerel board) if the TMU clock source
and/or clock event device is in use.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
This adds support for three new SoC types:
* The mvebu platform includes Marvell's Armada XP and Armada 370 chips,
made by the mvebu business unit inside of Marvell. Since the same
group also made the older but similar platforms we call "orion5x",
"kirkwood", "mv78xx0" and "dove", we plan to move all of them into
the mach-mvebu directory in the future.
* socfpga is Altera's platform based on Cortex-A9 cores and a lot of
FPGA space. This is similar to the Xilinx zynq platform we already
support. The code is particularly clean, which is helped by the fact
that the hardware doesn't do much besides the parts that are
expected to get added in the FPGA.
* The OMAP subarchitecture gains support for the latest generation,
the OMAP5 based on the new Cortex-A15 core. Support is rather
rudimentary for now, but will be extended in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=MwdJ
-----END PGP SIGNATURE-----
Merge tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull support for three new arm SoC types from Arnd Bergmann:
- The mvebu platform includes Marvell's Armada XP and Armada 370 chips,
made by the mvebu business unit inside of Marvell. Since the same
group also made the older but similar platforms we call "orion5x",
"kirkwood", "mv78xx0" and "dove", we plan to move all of them into
the mach-mvebu directory in the future.
- socfpga is Altera's platform based on Cortex-A9 cores and a lot of
FPGA space. This is similar to the Xilinx zynq platform we already
support. The code is particularly clean, which is helped by the fact
that the hardware doesn't do much besides the parts that are expected
to get added in the FPGA.
- The OMAP subarchitecture gains support for the latest generation, the
OMAP5 based on the new Cortex-A15 core. Support is rather
rudimentary for now, but will be extended in the future.
* tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
ARM: socfpga: initial support for Altera's SOCFPGA platform
arm: mvebu: generate DTBs for supported SoCs
ARM: mvebu: MPIC: read number of interrupts from control register
arm: mach-mvebu: add entry to MAINTAINERS
arm: mach-mvebu: add compilation/configuration change
arm: mach-mvebu: add defconfig
arm: mach-mvebu: add documentation for new device tree bindings
arm: mach-mvebu: add support for Armada 370 and Armada XP with DT
arm: mach-mvebu: add source files
arm: mach-mvebu: add header
clocksource: time-armada-370-xp: Marvell Armada 370/XP SoC timer driver
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
...
Conflicts:
Documentation/devicetree/bindings/arm/omap/omap.txt
arch/arm/mach-omap2/Makefile
drivers/clocksource/Kconfig
drivers/clocksource/Makefile
Make a common device tree glue for clocksource/dw_apb_timer.
Move mach-picoxcell/time.c to be a generic device tree application
of the dw_apb_timer.
Configure mach-picoxcell to use the dw_apb_timer_of device tree
implementation in drivers/clocksource.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Timer 0 is used as free-running clocksource, while timer 1 is used as
clock_event_device.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: John Stultz <johnstul@us.ibm.com>
This switches over to the now exported clockevents_config() and
clockevents_config_and_register() helpers. This knocks off a
long-standing TMU TODO item.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This platform has been obsoleted and was only available inside of
ST-Ericsson, no users of this code are left in the world. This
deletes the core U5500 support entirely in the same manner as the
obsoleted U8500 silicon was previously deleted.
The cpu_is_u5500() macros that can read out the CPU ID is left
until the next kernel cycle, this makes it possible to merge
deletion of dependent drivers without breakage.
This also has the upside of removing the mailbox driver which was
our only driver that was outside the drivers/* hiearchy, now the
machine directory only handles machines and nothing else.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit b519508298.
The reason for this revert is that making the frequency verification
preemptible and interruptible is not working reliably. Michaels
machine failed to use PM-timer with the message:
PM-Timer running at invalid rate: 113% of normal - aborting.
That's not a surprise as the frequency verification does rely on
interrupts being disabled. With a async scheduled thread there is no
guarantee to achieve the same result. Also some driver might fiddle
with the CTC channel 2 during the verification period, which makes the
result even more random and unpredictable.
This can be solved by using the same mechanism as we use in the
deferred TSC validation code, but that only will work if we verified a
working HPET _BEFORE_ trying to do the PM-Timer lazy validation.
So for now reverting is the safe option.
Bisected-by: Michael Witten <mfwitten@gmail.com>
Cc: Arjan van de Ven <arjanvandeven@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <alpine.LFD.2.02.1204112303270.2542@ionos>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUAT24/a2CrR//JCVInAQKYdxAAn+fs7yv+P4OWG/nIhGdnPw8MQ2u9fvqA
pmNL3Jy0eVowbENDcRRZgfhZ3ZlWBGUYym7J1uiFSrmHyJPoMtMvVg0miPYxLlpE
vr8bzuSfGOUOa7+Fk6kFVGxS3ZHZTsDvuhMQUIt/2jHgOaesqPvZ1FYFAj1bZ1fm
2CnQoF3OfnWAngHtoBXtgJxp/1r7+pHlGVbPYpmtHtikl45NmhqWza58aSQBilr+
S90cVeZs91gyveoxz5N+YrO8+Dx05te3mF+dwWuKC6aDC6d76fjLak54AvYv2Pzr
I6iaQPV8GIsXi5R4wptmVQAc5mbk5oktxJ7hCIHrmaBiAXygoVAYoqcuumoO3QDb
QKz10ga1yBYcKYrKvBzKxQrChw53IPU6po+Dd66ALJvLlc3KONksiJs5T/5Wma7P
v3VPcmZwPrJQbz+fQu6FysHeYQY+wfiR5E9Yz2OXs+PtkSy9OYsFFirdhJeWUPgA
ASjNLs1y5rxqrJBt7cjyQiBbIf1awGWyzF0yUNrlYHxmhJ6vcxHfrGoW38VRRCTM
8+JcxOHPRYrPfY7we6zsOn7ZeTWJduoUEeTxDnVS3w3zUIKCvkvkpHaJDvHvYcui
T/yJnXdUD2O3E5+5k/5cCyde8RbSB9gKsNpIMNkK5BLSmbux3C72dE0sMQFysahI
hS8aDCDUQUU=
=fMC+
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: device tree work" from Arnd Bergmann:
"Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h}
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits)
Document: devicetree: add OF documents for arch-mmp
ARM: dts: append DTS file of pxa168
ARM: mmp: append OF support on pxa168
ARM: mmp: enable rtc clk in pxa168
i2c: pxa: add OF support
serial: pxa: add OF support
arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
ARM: OMAP2+: Remove extra ifdefs for board-generic
ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
ASoC: DT: Add digital microphone binding to PAZ00 board.
ARM: dt: Add ARM PMU to tegra*.dtsi
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
...
Assorted extensions and fixes including:
* Introduction of early/late suspend/hibernation device callbacks.
* Generic PM domains extensions and fixes.
* devfreq updates from Axel Lin and MyungJoo Ham.
* Device PM QoS updates.
* Fixes of concurrency problems with wakeup sources.
* System suspend and hibernation fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=IGhc
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates for 3.4 from Rafael Wysocki:
"Assorted extensions and fixes including:
* Introduction of early/late suspend/hibernation device callbacks.
* Generic PM domains extensions and fixes.
* devfreq updates from Axel Lin and MyungJoo Ham.
* Device PM QoS updates.
* Fixes of concurrency problems with wakeup sources.
* System suspend and hibernation fixes."
* tag 'pm-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (43 commits)
PM / Domains: Check domain status during hibernation restore of devices
PM / devfreq: add relation of recommended frequency.
PM / shmobile: Make MTU2 driver use pm_genpd_dev_always_on()
PM / shmobile: Make CMT driver use pm_genpd_dev_always_on()
PM / shmobile: Make TMU driver use pm_genpd_dev_always_on()
PM / Domains: Introduce "always on" device flag
PM / Domains: Fix hibernation restore of devices, v2
PM / Domains: Fix handling of wakeup devices during system resume
sh_mmcif / PM: Use PM QoS latency constraint
tmio_mmc / PM: Use PM QoS latency constraint
PM / QoS: Make it possible to expose PM QoS latency constraints
PM / Sleep: JBD and JBD2 missing set_freezable()
PM / Domains: Fix include for PM_GENERIC_DOMAINS=n case
PM / Freezer: Remove references to TIF_FREEZE in comments
PM / Sleep: Add more wakeup source initialization routines
PM / Hibernate: Enable usermodehelpers in hibernate() error path
PM / Sleep: Make __pm_stay_awake() delete wakeup source timers
PM / Sleep: Fix race conditions related to wakeup source timer function
PM / Sleep: Fix possible infinite loop during wakeup source destruction
PM / Hibernate: print physical addresses consistently with other parts of kernel
...
Make the MTU2 clocksource driver mark its device as "always on"
using pm_genpd_dev_always_on() to protect it from surprise power
removals.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: stable@vger.kernel.org
Make the CMT clocksource driver mark its device as "always on"
using pm_genpd_dev_always_on() to protect it from surprise power
removals.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: stable@vger.kernel.org
Make the TMU clocksource driver mark its device as "always on"
using pm_genpd_dev_always_on() to protect it from surprise power
removals and make sh7372_add_standard_devices() add TMU devices on
sh7372 to the A4R power domain so that their "always on" flags
are taken into account as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: stable@vger.kernel.org
Shared timer IRQs are not a good solution, however the Geode platform has
no APIC, IRQs are a scarce resource and there is no technical reason to
forbid it rightaway. Increased latencies and overhead due to sharing are
still better than a driver refusing to load.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On SMP-capable kernels (e.g. generic distro kernel) the cs5535-clockevt
driver loads but is not actually used.
Setting cpumask to cpu_all_mask works for UP-only kernels, but if compiled
for SMP - though still running on the same UP hardware -
kernel/time/tick-common.c:tick_check_new_device() reads this as
"non-cpu-local" and silently ignores the device.
If we leave cpumask unset clockevents_register_device() will initialize it
and the cs5535-clockevt driver will be used no matter how the kernel was
compiled. Should anyone ever manage to stick a CS553x in an SMP system
(is this even possible?) then a warning will be printed. This is fine as
the cs5535-clockevt driver was never written/tested for SMP.
If bisecting led you here this patch may have exposed a pre-existing MFGPT
problem. Configure for UP-only and re-check.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some SoC have a 32 bit variant of Timer Counter Blocks. We do not
need the chaining of two 16 bit counters anymore for them.
The SoC nature is deduced from the device tree "compatible" string.
For non-device-tree configurations, backward compatibility is maintained
by using the default 16 bit counter configuration.
This patch addresses both the atmel_tclib and its user: tcb_clksrc
clocksource.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
This commit:
12d6d41276de: clocksource: scx200_hrt: Convert scx200 to use clocksource_register_hz
Breaks the build on x86-32:
drivers/clocksource/scx200_hrt.c: In function ‘init_hrt_clocksource’:
drivers/clocksource/scx200_hrt.c:95:0: error: unterminated argument list invoking macro "pr_info"
drivers/clocksource/scx200_hrt.c:84:2: error: ‘pr_info’ undeclared (first use in this function)
It could not possibly have been build tested, because it had this mismerge:
pr_info("enabling scx200 high-res timer (%s MHz +%d ppm)\n",
printk(KERN_INFO "enabling scx200 high-res timer (%s MHz +%d ppm)\n",
mhz27 ? "27":"1", ppm);
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/n/tip-jceb26fns5w7tv8edlivhxpa@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ACPI clocksource takes quite some time to initialize,
and this increases the boot time of the kernel for a
double digit percentage. This while almost all modern
systems will be using the HPET already anyway.
This patch turns the clocksource loading into an asynchronous
operation; which means it won't hold up the boot while
still becoming available normally.
To make this work well, an udelay() had to be turned into an
usleep_range() so that on UP systems, we yield the CPU to
regular boot tasks instead of spinning.
CC: John Stultz <johnstul@us.ibm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Len Brown <lenb@kernel.org>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Converts the scx200 clocksource to using clocksource_register_hz.
CC: Jim Cromie <jim.cromie@gmail.com>
Tested-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Switch from printk to using pr_<level>.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
[added commit msg & tweaked subject -jstultz]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[fixed up subject -jstultz]
Signed-off-by: John Stultz <john.stultz@linaro.org>
* 'for-linus' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: (207 commits)
ARM: 7267/1: Remove BUILD_BUG_ON from asm/bug.h
ARM: 7269/1: mach-sa1100: fix sched_clock breakage
ARM: 7198/1: arm/imx6: add restart support for imx6q
ARM: restart: remove the now empty arch_reset()
ARM: restart: remove comments about adding code to arch_reset()
ARM: restart: lpc32xx & u300: remove unnecessary printk
ARM: restart: plat-samsung: remove plat/reset.h and s5p_reset_hook
ARM: restart: w90x900: use new restart hook
ARM: restart: Versatile Express: use new restart hook
ARM: restart: versatile: use new restart hook
ARM: restart: u300: use new restart hook
ARM: restart: tegra: use new restart hook
ARM: restart: spear: use new restart hook
ARM: restart: shark: use new restart hook
ARM: restart: sa1100: use new restart hook
ARM: 7252/1: restart: S5PV210: use new restart hook
ARM: 7251/1: restart: S5PC100: use new restart hook
ARM: 7250/1: restart: S5P64X0: use new restart hook
ARM: 7266/1: restart: S3C64XX: use new restart hook
ARM: 7265/1: restart: S3C24XX: use new restart hook
...
Fix up trivial conflict in arch/arm/mm/init.c due to removal of
memblock_init() clashing with the movement of the sorting of the meminfo
array.
commit 2f0778afac adding
runtime-selectable sched_clock() forgot to patch this
driver down in drivers/clocksource, this patch fixes
the problem.
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The i8253 clockevent & clocksource driver uses PIT_LATCH
except for two cases where it uses LATCH:
1)
/* VIA686a test code... reset the latch if count > max + 1 */
if (count > LATCH) {
LATCH is based on CLOCK_TICK_RATE which is defined as
PIT_TICK_RATE on x86 so this should just be the later.
2)
...
switch (mode) {
case CLOCK_EVT_MODE_PERIODIC:
/* binary, mode 2, LSB/MSB, ch 0 */
outb_p(0x34, PIT_MODE);
outb_p(LATCH & 0xff , PIT_CH0); /* LSB */
outb_p(LATCH >> 8 , PIT_CH0); /* MSB */
...
MIPS and ARM are the only other arches that use this driver. In
the MIPS case CLOCK_TICK_RATE is defined as the same value as
PIT_TICK_RATE. For ARM, the only machine that uses it is
Footbridge which has a totally bogus CLOCK_TICK_RATE according
to the comments. Furthermore, the clockevent_i8253_init()
initializes the clockevent with PIT_TIC_RATE, so there's
no reason to use the generic LATCH.
This is part of work to remove and depecrate the global
CLOCK_TICK_RATE symbol.
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The acpi_pm clocksource driver uses CLOCK_TICK_RATE which is
defined as PIT_TICK_RATE on x86. This patch cleans it up to
just use the later so that CLOCK_TICK_RATE can be depecrated.
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in clocksource
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
The clocksource name should be const for correctness.
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Based on a patch from Arnd Bergmann this fixes up the build
problem of assigning a non-existing global when the ux500 PRCMU
timer is not linked in by passing its base address to the init
function. We also add a missing <linux/errno.h> inclusion and
staticize the dummy function.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the DBX500 PRCMU Timer driver as a clocksource
and as sched_clock.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: apb: Share APB timer code with other platforms
Add code to the CMT driver to wait for CMCNT V2. This to let
the register value settle before starting the timer channel.
Makes the driver more robust.
Needed for CMT2 on sh7372 and certain CMT channels on sh73a0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
arm, mips and x86 implement i8253 based clockevents. All the same code
copied. Create a common implementation in drivers/clocksource/i8253.c.
About time to rename drivers/clocksource/ to something else.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/20110609130621.921710458@linutronix.de
The APB timers are an IP block from Synopsys (DesignWare APB timers)
and are also found in other systems including ARM SoC's. This patch
adds functions for creating clock_event_devices and clocksources from
APB timers but does not do the resource allocation. This is handled
in a higher layer to allow the timers to be created from multiple
methods such as platform_devices.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that all extra ifdeffed implementations are gone, depend the lock
export on PCSPKR_PLATFORM
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@arm.linux.org.uk>
Move them to drivers/clocksource/i8253.c and remove the
implementations in arch/
[ tglx: Avoid the extra file in lib - folded arch patches in. The
export will become conditional in a later step ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/20110601180610.221426078@duck.linux-mips.net
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit 1b842e91fe.
There is a fundamental ordering race between the early and late probe
paths and the runtime PM tie-in that results in __pm_runtime_resume()
attempting to take a lock that hasn't been initialized yet (which by
proxy also suggests that pm_runtime_init() hasn't yet been run on the
device either, making the entire thing unsafe) -- resulting in instant
death on SMP or on UP with spinlock debugging enabled:
sh_tmu.0: used for clock events
sh_tmu.0: used for periodic clock events
BUG: spinlock trylock failure on UP on CPU#0, swapper/0
lock: 804db198, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
...
Revert it for now until the ordering issues can be resolved, or we can get
some more help from the runtime PM framework to make this possible.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'sh-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Ignore R_SH_NONE module relocations.
SH: SE7751: Fix pcibios_map_platform_irq prototype.
sh: remove warning and warning_symbol from struct stacktrace_ops
sh: wire up sys_sendmmsg.
clocksource: sh_tmu: Runtime PM support
clocksource: sh_tmu: __clocksource_updatefreq_hz() update
clocksource: sh_cmt: Runtime PM support
clocksource: sh_cmt: __clocksource_updatefreq_hz() update
dmaengine: shdma: synchronize RCU before freeing, simplify spinlock
dmaengine: shdma: add runtime- and system-level power management
dmaengine: shdma: fix locking
sh: sh-sci: sh7377 and sh73a0 build fixes
sh: cosmetic improvement: use an existing pointer
serial: sh-sci: suspend/resume wakeup support V2
serial: sh-sci: Runtime PM support
sh: select IRQ_FORCED_THREADING.
sh: intc: Set virtual IRQs as nothread.
sh: fixup fpu.o compile order
i2c: add a module alias to the sh-mobile driver
ALSA: add a module alias to the FSI driver
...
Add a generic mmio clocksource, covering both 32-bit and 16-bit register
access sizes, for up or down counters. This can be used to easily
create clocksources for simple counter-based implementations.
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Colin Cross <ccross@android.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Erik Gilling <konkers@android.com>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: linux-omap@vger.kernel.org
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Cc: Olof Johansson <olof@lixom.net>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Runtime PM support to the TMU driver.
The hardware device is enabled as long as the clocksource
or the clockevent portion of the driver is used.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the clocksource part of the TMU driver
to make use of the __clocksource_updatefreq_hz() function.
Without this patch the old code uses clocksource_register()
together with a hack that assumes a never changing clock rate
(see clk_enable(), clk_get_rate() and clk_disable()).
The patch uses clocksource_register_hz() with 1 Hz as initial
value, then lets the ->enable() callback update the value
with __clocksource_updatefreq_hz() once the struct clk has
been enabled and the frequency is stable.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add Runtime PM support to the CMT driver.
The hardware device is enabled as long as the clocksource
or the clockevent portion of the driver is used.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the clocksource part of the CMT driver
to make use of the __clocksource_updatefreq_hz() function.
Without this patch the old code uses clocksource_register()
together with a hack that assumes a never changing clock rate
(see clk_enable(), clk_get_rate() and clk_disable()).
The patch uses clocksource_register_hz() with 1 Hz as initial
value, then lets the ->enable() callback update the value
with __clocksource_updatefreq_hz() once the struct clk has
been enabled and the frequency is stable.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Conflicts:
arch/ia64/kernel/cyclone.c
arch/mips/kernel/i8253.c
arch/x86/kernel/i8253.c
Reason: Resolve conflicts so further cleanups do not conflict further
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is based upon both arch/arm/mach-footbridge/isa-timer.c and
arch/x86/kernel/i8253.c.
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This converts the remaining x86 clocksources to use
clocksource_register_hz/khz.
CC: jacob.jun.pan@intel.com
CC: Glauber Costa <glommer@redhat.com>
CC: Dimitri Sivanich <sivanich@sgi.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Jeremy Fitzhardinge <jeremy@xensource.com>
CC: Chris McDermott <lcm@us.ibm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
setup_irq() was called before clockevents_register_device() which is
needed by the irq handler. Bug was reproducible by restarting the
kernel using kexec (reliable crash).
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the acpi pm timer throws invalid data, clear pmtmr_ioport
so the pm timer won't accidentally be used.
This was found when using Xen where there is a acpi pm reported,
but gives bogus values, and other code was continuing to try
to use the pm timer after the initialization failed.
[jstultz: Catch additional failure and reword changelog message. ]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1295027246-11110-1-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are control flow that sh_cmt_set_next() does double
spin-lock. The callers sh_cmt_{start,stop}() already have
lock. But another callers sh_cmt_clock_event_{start,next}()
does not.
Now sh_cmt_set_next() does not lock by itself. All the
callers should hold spin-lock before calling it.
[damm@opensource.se: use __sh_cmt_set_next() to simplify code]
[damm@opensource.se: added stable, suitable for v2.6.35 + v2.6.36]
Cc: stable@kernel.org
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now when the SH-Mobile ARM platforms have been converted
to use device name it is possible to remove "clk" from
struct sh_timer_config.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the rate calculation in the CMT driver.
Without this fix the clocksource runs way
too fast and we get a divide-by-zero error.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix a one-off error in the CMT driver V2. The match register
should be programmed with the period minus one.
Many thanks to Eiraku-san for tracking down this issue.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the most common of the x86 clocksources over to use
clocksource_register_hz/khz.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-11-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
My Collabora address is no longer enabled - update the MODULE_AUTHOR
fields of drivers to my current email address.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous CMT fixup accidentally copied in the TMU shift value, reset
this back to its original value while preserving the TMU fix.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Based on the sh_tmu change in 66f49121ff
("clocksource: sh_tmu: compute mult and shift before registration").
The same issues impact the sh_cmt driver, so we take the same approach
here.
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since commit 98962465ed ("nohz: Prevent
clocksource wrapping during idle"), the CPU of an R2D board never goes
to idle. This commit assumes that mult and shift are assigned before
the clocksource is registered. As a consequence the safe maximum sleep
time is negative and the CPU never goes into idle.
This patch fixes the problem by moving mult and shift initialization
from sh_tmu_clocksource_enable() to sh_tmu_register_clocksource().
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure that the timer IRQs and IPIs aren't enabled for IRQ balancing.
IPIs are disabled as a result of being percpu while the timers simply
disable balancing outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
We want to get rid of the clock string from platform data entirely,
depending on the clkdev-based clock lookup to do the right thing for us
instead.
This converts all of the SH drivers to request their associated function
clocks directly, and if there is no match for that then we fall back on
the legacy lookup while warning about it. After all of the outstanding
CPUs have been converted to clkdev lookups the clock string will be
killed off completely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Due to a hardware limitation cs5535_mfgpt_free_timer() cannot actually
release the timer hardware, but it will at least free the now unreferenced
struct associated with it so calling it is the cleaner thing to do.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no need to copy in the name from the sh timer config now that
dev_name() is available early. We prefer the dev_name() variant for
consistent naming.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the CS5535 MFGPT hrtimer kconfig option to be with the other MFGPT
options. This makes it easier to find and also removes it from the main
"Device Drivers" menu, where it should not have been.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (187 commits)
sh: remove dead LED code for migo-r and ms7724se
sh: ecovec build fix for CONFIG_I2C=n
sh: ecovec r-standby support
sh: ms7724se r-standby support
sh: SH-Mobile R-standby register save/restore
clocksource: Fix up a registration/IRQ race in the sh drivers.
sh: ms7724: modify scan_timing for KEYSC
sh: ms7724: Add sh_sir support
sh: mach-ecovec24: Add sh_sir support
sh: wire up SET/GET_UNALIGN_CTL.
sh: allow alignment fault mode to be configured at kernel boot.
sh: sh7724: Update FSI/SPU2 clock
sh: always enable sh7724 vpu_clk and set to 166MHz on Ecovec
sh: add sh7724 kick callback to clk_div4_table
sh: introduce struct clk_div4_table
sh: clock-cpg div4 set_rate() shift fix
sh: Turn on speculative return for SH7785 and SH7786
sh: Merge legacy and dynamic PMB modes.
sh: Use uncached I/O helpers in PMB setup.
sh: Provide uncached I/O helpers.
...
All of the SH clocksource drivers follow the scheme that the IRQ is setup
prior to registering the clockevent. The interrupt handler in the
clockevent cases looks to the event handler function pointer being filled
in by the registration code, permitting us to get in to situations where
asserted IRQs step in to the handler before registration has had a chance
to complete and hitting a NULL pointer deref.
In practice this is not an issue for most platforms, but some of them
with fairly special loaders (or that are chain-loading from another
kernel) may enter in to this situation. This fixes up the oops reported
by Rafael on hp6xx.
Reported-and-tested-by: Rafael Ignacio Zurita <rafaelignacio.zurita@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
geode-mfgpt: restore previous behavior for selecting IRQ
The MFGPT IRQ used to be, in order of decreasing priority,
* IRQ supplied by the user as a boot-time parameter,
* IRQ previously set by the BIOS or another driver,
* default IRQ given at compile time.
Return to this behavior, which got broken when splitting the
MFGPT/clocksource driver for 2.6.33-rc1.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add code to start the CMT timer on clocksource resume. While at it handle
the suspend case as well. Remove the platform device specific suspend
calls.
This makes sure the timer is started during sysdev_resume(). Without this
patch the clocksource may be read as suspended, this after sysdev resume
but before platform device resume.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is based on the old code in arch/x86/kernel/mfgpt_32.c, but is
modular and not Geode-specific. There's no reason why the clock event
device needs to be registered so early at boot; the clockevent code is
perfectly capable of dynamic switching.
[akpm@linux-foundation.org: add linux/irq.h include]
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch updates the SuperH CMT driver with suspend and resume
callbacks for the suspend-to-ram case. This patch stops the CMT
channel at suspend time to avoid unwanted wake up events.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Avoid undocumented vague TMU behavior when zero value is set to TCOR.
This primarily fixes up issues encountered under qemu with a zero-length
period, while the hardware itself is fairly ambivalent one way or the
other.
Signed-off-by: Shin-ichiro KAWASAKI <kawasaki@juno.dti.ne.jp>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Simon Arlott