Now that all the boards using OMAP HDMI are using DT boot, we can remove
the hacks for getting the ioresources with non-DT boot.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This adds a new driver to omapdss for OMAP5 HDMI. However, the new
driver uses common HDMI files which are shared with OMAP4 HDMI driver.
OMAP5 HDMI has a different HDMI core IP compared to OMAP4, but has very
similar PLL and PHY IPs which can be handled with common code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a features struct to differentiate between the HDMI PLLs on OMAP4
and OMAP5. The OMAP5 PLL is more sensitive when it comes to locking. We
need to ensure that the DCO freq isn't too low for lower pixel clocks.
Modify the PLL computation slightly to ensure the HDMI PLL locks for lower
frequencies. This will be later replaced by a more complex computation
which makes sure all the PLL constraints are met.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5 HDMI PHY has some differences compared to OMAP4 HDMI PHY. This
patch creates a features struct which help the driver configure the PHY
based on what SoC it is.
Some of the features aren't currenlty used, but will come in use later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI core IP on OMAP5 has a wider address range for registers. The offsets
for the later registers can't fit into the u16 type currently used for hdmi
register read and write functions. Use u32 for offsets instead.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI IRQ handling was moved into hdmi_phy.c when restructuring the HDMI
driver. While this worked fine, it's not correct.
The HDMI IRQ handling should be either in the hdmi_wp, or in the main
hdmi driver. This patch moves the handling to the main hdmi driver, as I
feel it's a more appropriate choice.
This move also requires changing the handling of the PHY power, as that
was partly handled in the IRQ handler. The PHY power is handled via the
WP module. An option would be to give HDMI PHY driver function pointers
that it could use to manage the PHY power, but as the PHY power is not
needed to access the PHY registers, the handling was also moved to the
main HDMI driver. This could be changed later if need be.
Note that there's slightly similar power issue with the PLL: the HDMI
PLLs power is also handled via the WP module. For now, the PLL power
handling is still done inside the PLL driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We'll soon add support for OMAP5 HDMI, which uses some of the same files
as OMAP4 HDMI does.
This patch adds a new config entry "OMAP2_DSS_HDMI_COMMON", which both
OMAP4 and OMAP5 HDMI config entries can select. OMAP2_DSS_HDMI_COMMON
will cause the common HDMI files to be compiled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment the dpi driver does not handle LCD3 clock source at all.
LCD3 channel gets the DSI PLL clock from DSI2 instance. Add support for
LCD3's clock source in the dpi driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5 has LCD3 overlay manager, and total 4 overlay managers. These are
not correctly defined in the dss features. Fix them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add DSS features for AM43xx.
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The use of venc_panel.c was removed in
09d2e7cdeb (OMAPDSS: VENC: remove code
related to old panel model), but the file itself was left behind. Remove
the unused file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The support for simpler port/endpoint binding was removed in the merged version
of omapdss DT. But dss_init_ports still tries to get to an endpoint even if no
port exists. Remove this as this doesn't work.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_uninit_ports is only called by __exit omap_dsshw_remove
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-omap@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
fb_image.dx, fb_image.dy and fbconf2bmap.framebuffer are __u32
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All other Goldfish drivers depend on GOLDFISH, I see no reason why the
framebuffer driver would be an exception.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All drivers under menu EXYNOS_VIDEO depend on either ARCH_S5PV210 or
ARCH_EXYNOS, so add these as dependencies to the menu itself. This
avoids presenting an empty and useless menu on other architectures.
Then drivers under the menu only need a dependency if they depend on
one of the supported architectures specifically.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace kzalloc by devm_kzalloc and remove the kfree() calls.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The frame buffer core may be a loadable module, and in this
case, the nuc900 driver cannot be built-in. Turning it into
a tristate option lets Kconfig work out the dependency and
avoid broken builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The atmel frame buffer driver doesn't build if FB_BACKLIGHT
is disabled, so select it here as we do for lots of other
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Some drivers that may be loadable modules use the fb_prepare_logo
function, so we have to export it. Found during randconfig
builds with mmpfb.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The mbx framebuffer debugfs support apparently hasn't been able
to build for a long time, at least since 2006 when the u.generic_ip
field in the inode was removed. This fixes the obvious bug, and
also makes it possible to build the driver as a module when
debugfs support is enabled, by simply including the C file.
It's ugly, but it won't make the driver any worse than it
already is, and doesn't require a more invasive change that
might break it further.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Raphael Assenat <raph@8d.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The framebuffer layer can be a loadable module, which forces
omapfb to be a module as well. However, this breaks the lcd
drivers, which are linked into the omapfb driver but each
have their own module_init() function. To solve this,
we split out the lcd drivers into separate modules and
export omapfb_register_panel, which is the only interface
required between the main omapfb driver and the lcd panel
drivers.
We also have to introduce a new Kconfig symbol for H3, since
that lcd driver has a dependency on TPS65010, which we can
express better in Kconfig than Makefile syntax.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can only use I2C support in frame buffer drivers if
Either I2C is built-in, or both I2C and the driver itself
are loadable modules.
Fix this dependency for MB862XX and CyberPro frame buffers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If LPAE is enabled, dma_addr_t is 64 bit, so we have to
change a few type for everything in this driver to match
again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add module alias string to make it working when panel is compiled as module.
Without this change panel module is not probed thus display is not working.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sh_mobile_lcdcfb driver calls interfaces provided
by the corresponding "meram" helper. This fails if meram
is a module but lcdcfb is built-in.
To work around it, this uses special Kconfig magic to
only allow lcdcfb to be built if
a) both are modules,
b) meram is built-in, or
c) meram is disabled and the helpers stubbed out
Changing meram from 'y' to 'm' now forces clcd to
be a module as well, which seems to be the desired
behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: linux-sh@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Set the DSI vdd regulator voltage to the required 1.8V.
This is required for the case when the regulator in the DT data defines
a range of allowed voltages. In this case it's required to set the
voltage, as otherwise enabling the voltage fails.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Set the HDMI vdda regulator voltage to the required 1.8V.
This is required for the case when the regulator in the DT data defines
a range of allowed voltages. In this case it's required to set the
voltage, as otherwise enabling the voltage fails.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support to configure the pins used for the HDMI lanes. The order and
polarity of the lanes can be defined in the DT data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support to handle HPD GPIO in the HDMI connector driver. For the
time being, the driver only uses HPD GPIO to report is the cable is
connected via detect() calll.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add DT support for panel-dpi.
We disable the use of the backlight_gpio as it should be handled via
backlight framework with DT boots.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
The new gpiod API supports automatic handling of active-high/active-low
with DT. To make it possible to use that when booting with DT, change
the panel-dpi's handling of the enable GPIO to use gpiod.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The tmiofb driver should not depend on MFD_CORE but on MFD_TMIO.
Without the tmio_core driver, tmiofb has no platform device to bind
to and is thus useless.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Sparse complains about using zero instead of NULL for pointers.
Probably, if we enabled the warning, then GCC would complain about the
unused initializers. I've just removed them.
Smatch complains that we first check if "fbi" is NULL and then
dereference it in the error handling. It turns out that "fbi" can't be
NULL so I've removed the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
References to the Kconfig symbol CPU_PXA988 were added to the tree in
v3.9. But that Kconfig symbol has never been part of the tree. So get
rid of these references.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
References to the Kconfig symbol CPU_MMP3 were added to the tree since
v3.6. But that Kconfig symbol has never been part of the tree. So get
rid of these references.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix format string mismatch in gbefb_show_memsize().
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix format string mismatch in contrast_show().
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Check EDID Vendor Specific Data Block bytes to see if the connection
is HDMI and set FB_MISC_HDMI.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Christopher Freeman <cfreeman@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of having fbdev framework core files at the root fbdev
directory, mixed with random fbdev device drivers, move the fbdev core
files to a separate core directory. This makes it much clearer which of
the files are actually part of the fbdev framework, and which are part
of device drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The drivers/video directory is a mess. It contains generic video related
files, directories for backlight, console, linux logo, lots of fbdev
device drivers, fbdev framework files.
Make some order into the chaos by creating drivers/video/fbdev
directory, and move all fbdev related files there.
No functionality is changed, although I guess it is possible that some
subtle Makefile build order related issue could be created by this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tomi Valkeinen