Trigger a switchdev event whenever the bridge's MST mode is
enabled/disabled. This allows constituent ports to either perform any
required hardware config, or refuse the change if it not supported.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add vlan push_eth and pop_eth action to the hardware intermediate
representation model which would subsequently allow it to be used
by drivers for offload.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that devlink ports are protected by the instance lock
it seems natural to pass devlink_port as an argument to
the port_split / port_unsplit callbacks.
This should save the drivers from doing a lookup.
In theory drivers may have supported unsplitting ports
which were not registered prior to this change.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It should be familiar and beneficial to expose devlink instance
lock to the drivers. This way drivers can block devlink from
calling them during critical sections without breakneck locking.
Add port helpers, port splitting callbacks will be the first
target.
Use 'devl_' prefix for "explicitly locked" API. Initial RFC used
'__devlink' but that's too much typing.
devl_lock_is_held() is not defined without lockdep, which is
the same behavior as lockdep_is_held() itself.
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The fundamental premise of VRF and l3mdev core code is binding a socket
to a device (l3mdev or netdev with an L3 domain) to indicate L3 scope.
Legacy code resets flowi_oif to the l3mdev losing any original port
device binding. Ben (among others) has demonstrated use cases where the
original port device binding is important and needs to be retained.
This patch handles that by adding a new entry to the common flow struct
that can indicate the l3mdev index for later rule and table matching
avoiding the need to reset flowi_oif.
In addition to allowing more use cases that require port device binds,
this patch brings a few datapath simplications:
1. l3mdev_fib_rule_match is only called when walking fib rules and
always after l3mdev_update_flow. That allows an optimization to bail
early for non-VRF type uses cases when flowi_l3mdev is not set. Also,
only that index needs to be checked for the FIB table id.
2. l3mdev_update_flow can be called with flowi_oif set to a l3mdev
(e.g., VRF) device. By resetting flowi_oif only for this case the
FLOWI_FLAG_SKIP_NH_OIF flag is not longer needed and can be removed,
removing several checks in the datapath. The flowi_iif path can be
simplified to only be called if the it is not loopback (loopback can
not be assigned to an L3 domain) and the l3mdev index is not already
set.
3. Avoid another device lookup in the output path when the fib lookup
returns a reject failure.
Note: 2 functional tests for local traffic with reject fib rules are
updated to reflect the new direct failure at FIB lookup time for ping
rather than the failure on packet path. The current code fails like this:
HINT: Fails since address on vrf device is out of device scope
COMMAND: ip netns exec ns-A ping -c1 -w1 -I eth1 172.16.3.1
ping: Warning: source address might be selected on device other than: eth1
PING 172.16.3.1 (172.16.3.1) from 172.16.3.1 eth1: 56(84) bytes of data.
--- 172.16.3.1 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms
where the test now directly fails:
HINT: Fails since address on vrf device is out of device scope
COMMAND: ip netns exec ns-A ping -c1 -w1 -I eth1 172.16.3.1
ping: connect: No route to host
Signed-off-by: David Ahern <dsahern@kernel.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20220314204551.16369-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net coming late
in the 5.17-rc process:
1) Revert port remap to mitigate shadowing service ports, this is causing
problems in existing setups and this mitigation can be achieved with
explicit ruleset, eg.
... tcp sport < 16386 tcp dport >= 32768 masquerade random
This patches provided a built-in policy similar to the one described above.
2) Disable register tracking infrastructure in nf_tables. Florian reported
two issues:
- Existing expressions with no implemented .reduce interface
that causes data-store on register should cancel the tracking.
- Register clobbering might be possible storing data on registers that
are larger than 32-bits.
This might lead to generating incorrect ruleset bytecode. These two
issues are scheduled to be addressed in the next release cycle.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: disable register tracking
Revert "netfilter: conntrack: tag conntracks picked up in local out hook"
Revert "netfilter: nat: force port remap to prevent shadowing well-known ports"
====================
Link: https://lore.kernel.org/r/20220312220315.64531-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to the port-based default priority, IEEE 802.1Q-2018 allows the
Application Priority Table to define QoS classes (0 to 7) per IP DSCP
value (0 to 63).
In the absence of an app table entry for a packet with DSCP value X,
QoS classification for that packet falls back to other methods (VLAN PCP
or port-based default). The presence of an app table for DSCP value X
with priority Y makes the hardware classify the packet to QoS class Y.
As opposed to the default-prio where DSA exposes only a "set" in
dsa_switch_ops (because the port-based default is the fallback, it
always exists, either implicitly or explicitly), for DSCP priorities we
expose an "add" and a "del". The addition of a DSCP entry means trusting
that DSCP priority, the deletion means ignoring it.
Drivers that already trust (at least some) DSCP values can describe
their configuration in dsa_switch_ops :: port_get_dscp_prio(), which is
called for each DSCP value from 0 to 63.
Again, there can be more than one dcbnl app table entry for the same
DSCP value, DSA chooses the one with the largest configured priority.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port-based default QoS class is assigned to packets that lack a
VLAN PCP (or the port is configured to not trust the VLAN PCP),
an IP DSCP (or the port is configured to not trust IP DSCP), and packets
on which no tc-skbedit action has matched.
Similar to other drivers, this can be exposed to user space using the
DCB Application Priority Table. IEEE 802.1Q-2018 specifies in Table
D-8 - Sel field values that when the Selector is 1, the Protocol ID
value of 0 denotes the "Default application priority. For use when
application priority is not otherwise specified."
The way in which the dcbnl integration in DSA has been designed has to
do with its requirements. Andrew Lunn explains that SOHO switches are
expected to come with some sort of pre-configured QoS profile, and that
it is desirable for this to come pre-loaded into the DSA slave interfaces'
DCB application priority table.
In the dcbnl design, this is possible because calls to dcb_ieee_setapp()
can be initiated by anyone including being self-initiated by this device
driver.
However, what makes this challenging to implement in DSA is that the DSA
core manages the net_devices (effectively hiding them from drivers),
while drivers manage the hardware. The DSA core has no knowledge of what
individual drivers' QoS policies are. DSA could export to drivers a
wrapper over dcb_ieee_setapp() and these could call that function to
pre-populate the app priority table, however drivers don't have a good
moment in time to do this. The dsa_switch_ops :: setup() method gets
called before the net_devices are created (dsa_slave_create), and so is
dsa_switch_ops :: port_setup(). What remains is dsa_switch_ops ::
port_enable(), but this gets called upon each ndo_open. If we add app
table entries on every open, we'd need to remove them on close, to avoid
duplicate entry errors. But if we delete app priority entries on close,
what we delete may not be the initial, driver pre-populated entries, but
rather user-added entries.
So it is clear that letting drivers choose the timing of the
dcb_ieee_setapp() call is inappropriate. The alternative which was
chosen is to introduce hardware-specific ops in dsa_switch_ops, and
effectively hide dcbnl details from drivers as well. For pre-populating
the application table, dsa_slave_dcbnl_init() will call
ds->ops->port_get_default_prio() which is supposed to read from
hardware. If the operation succeeds, DSA creates a default-prio app
table entry. The method is called as soon as the slave_dev is
registered, but before we release the rtnl_mutex. This is done such that
user space sees the app table entries as soon as it sees the interface
being registered.
The fact that we populate slave_dev->dcbnl_ops with a non-NULL pointer
changes behavior in dcb_doit() from net/dcb/dcbnl.c, which used to
return -EOPNOTSUPP for any dcbnl operation where netdev->dcbnl_ops is
NULL. Because there are still dcbnl-unaware DSA drivers even if they
have dcbnl_ops populated, the way to restore the behavior is to make all
dcbnl_ops return -EOPNOTSUPP on absence of the hardware-specific
dsa_switch_ops method.
The dcbnl framework absurdly allows there to be more than one app table
entry for the same selector and protocol (in other words, more than one
port-based default priority). In the iproute2 dcb program, there is a
"replace" syntactical sugar command which performs an "add" and a "del"
to hide this away. But we choose the largest configured priority when we
call ds->ops->port_set_default_prio(), using __fls(). When there is no
default-prio app table entry left, the port-default priority is restored
to 0.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210113154139.1803705-2-olteanv@gmail.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
ice: GTP support in switchdev
Marcin Szycik says:
Add support for adding GTP-C and GTP-U filters in switchdev mode.
To create a filter for GTP, create a GTP-type netdev with ip tool, enable
hardware offload, add qdisc and add a filter in tc:
ip link add $GTP0 type gtp role <sgsn/ggsn> hsize <hsize>
ethtool -K $PF0 hw-tc-offload on
tc qdisc add dev $GTP0 ingress
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
action mirred egress redirect dev $VF1_PR
By default, a filter for GTP-U will be added. To add a filter for GTP-C,
specify enc_dst_port = 2123, e.g.:
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
enc_dst_port 2123 action mirred egress redirect dev $VF1_PR
Note: outer IPv6 offload is not supported yet.
Note: GTP-U with no payload offload is not supported yet.
ICE COMMS package is required to create a filter as it contains GTP
profiles.
Changes in iproute2 [1] are required to be able to add GTP netdev and use
GTP-specific options (QFI and PDU type).
[1] https://lore.kernel.org/netdev/20220211182902.11542-1-wojciech.drewek@intel.com/T
---
v2: Add more CC
v3: Fix mail thread, sorry for spam
v4: Add GTP echo response in gtp module
v5: Change patch order
v6: Add GTP echo request in gtp module
v7: Fix kernel-docs in ice
v8: Remove handling of GTP Echo Response
v9: Add sending of multicast message on GTP Echo Response, fix GTP-C dummy
packet selection
v10: Rebase, fixed most 80 char line limits
v11: Rebase, collect Harald's Reviewed-by on patch 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Before adding yet another possibly contended atomic_long_t,
it is time to add per-cpu storage for existing ones:
dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler
Because many devices do not have to increment such counters,
allocate the per-cpu storage on demand, so that dev_get_stats()
does not have to spend considerable time folding zero counters.
Note that some drivers have abused these counters which
were supposed to be only used by core networking stack.
v4: should use per_cpu_ptr() in dev_get_stats() (Jakub)
v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo)
v2: add a missing include (reported by kernel test robot <lkp@intel.com>)
Change in netdev_core_stats_alloc() (Jakub)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: jeffreyji <jeffreyji@google.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When iterating over sockets using vsock_for_each_connected_socket, make
sure that a transport filters out sockets that don't belong to the
transport.
There actually was an issue caused by this; in a nested VM
configuration, destroying the nested VM (which often involves the
closing of /dev/vhost-vsock if there was h2g connections to the nested
VM) kills not only the h2g connections, but also all existing g2h
connections to the (outmost) host which are totally unrelated.
Tested: Executed the following steps on Cuttlefish (Android running on a
VM) [1]: (1) Enter into an `adb shell` session - to have a g2h
connection inside the VM, (2) open and then close /dev/vhost-vsock by
`exec 3< /dev/vhost-vsock && exec 3<&-`, (3) observe that the adb
session is not reset.
[1] https://android.googlesource.com/device/google/cuttlefish/
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jiyong Park <jiyong@google.com>
Link: https://lore.kernel.org/r/20220311020017.1509316-1-jiyong@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
-----BEGIN PGP SIGNATURE-----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=ccps
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
brcmfmac
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
* tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits)
mac80211: Add support to trigger sta disconnect on hardware restart
mac80211: fix potential double free on mesh join
mac80211: correct legacy rates check in ieee80211_calc_rx_airtime
nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation
mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible
mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
rtw89: 8852c: process logic efuse map
rtw89: 8852c: process efuse of phycap
rtw89: support DAV efuse reading operation
rtw89: 8852c: add chip::dle_mem
rtw89: add page_regs to handle v1 chips
rtw89: add chip_info::{h2c,c2h}_reg to support more chips
rtw89: add hci_func_en_addr to support variant generation
rtw89: add power_{on/off}_func
rtw89: read chip version depends on chip ID
rtw89: pci: use a struct to describe all registers address related to DMA channel
rtw89: pci: add V1 of PCI channel address
rtw89: pci: add struct rtw89_pci_info
rtw89: 8852c: add 8852c empty files
MAINTAINERS: add devicetree bindings entry for mt76
...
====================
Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a function that checks if a net device type is GTP.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Options are as follows: PDU_TYPE:QFI and they refernce to
the fields from the PDU Session Protocol. PDU Session data
is conveyed in GTP-U Extension Header.
GTP-U Extension Header is described in 3GPP TS 29.281.
PDU Session Protocol is described in 3GPP TS 38.415.
PDU_TYPE - indicates the type of the PDU Session Information (4 bits)
QFI - QoS Flow Identifier (6 bits)
# ip link add gtp_dev type gtp role sgsn
# tc qdisc add dev gtp_dev ingress
# tc filter add dev gtp_dev protocol ip parent ffff: \
flower \
enc_key_id 11 \
gtp_opts 1:8/ff:ff \
action mirred egress redirect dev eth0
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adding GTP device through ip link creates the situation where
there is no userspace daemon which would handle GTP messages
(Echo Request for example). GTP-U instance which would not respond
to echo requests would violate GTP specification.
When GTP packet arrives with GTP_ECHO_REQ message type,
GTP_ECHO_RSP is send to the sender. GTP_ECHO_RSP message
should contain information element with GTPIE_RECOVERY tag and
restart counter value. For GTPv1 restart counter is not used
and should be equal to 0, for GTPv0 restart counter contains
information provided from userspace(IFLA_GTP_RESTART_COUNT).
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Suggested-by: Harald Welte <laforge@gnumonks.org>
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Tested-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently in case of target hardware restart, we just reconfig and
re-enable the security keys and enable the network queues to start
data traffic back from where it was interrupted.
Many ath10k wifi chipsets have sequence numbers for the data
packets assigned by firmware and the mac sequence number will
restart from zero after target hardware restart leading to mismatch
in the sequence number expected by the remote peer vs the sequence
number of the frame sent by the target firmware.
This mismatch in sequence number will cause out-of-order packets
on the remote peer and all the frames sent by the device are dropped
until we reach the sequence number which was sent before we restarted
the target hardware
In order to fix this, we trigger a sta disconnect, in case of target
hw restart. After this there will be a fresh connection and thereby
avoiding the dropping of frames by remote peer.
The right fix would be to pull the entire data path into the host
which is not feasible or would need lots of complex changes and
will still be inefficient.
Tested on ath10k using WCN3990, QCA6174
Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
Link: https://lore.kernel.org/r/20220308115325.5246-2-youghand@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today's implementation of csum_shift() leads to branching based on
parity of 'offset'
000002f8 <csum_block_add>:
2f8: 70 a5 00 01 andi. r5,r5,1
2fc: 41 a2 00 08 beq 304 <csum_block_add+0xc>
300: 54 84 c0 3e rotlwi r4,r4,24
304: 7c 63 20 14 addc r3,r3,r4
308: 7c 63 01 94 addze r3,r3
30c: 4e 80 00 20 blr
Use first bit of 'offset' directly as input of the rotation instead of
branching.
000002f8 <csum_block_add>:
2f8: 54 a5 1f 38 rlwinm r5,r5,3,28,28
2fc: 20 a5 00 20 subfic r5,r5,32
300: 5c 84 28 3e rotlw r4,r4,r5
304: 7c 63 20 14 addc r3,r3,r4
308: 7c 63 01 94 addze r3,r3
30c: 4e 80 00 20 blr
And change to left shift instead of right shift to skip one more
instruction. This has no impact on the final sum.
000002f8 <csum_block_add>:
2f8: 54 a5 1f 38 rlwinm r5,r5,3,28,28
2fc: 5c 84 28 3e rotlw r4,r4,r5
300: 7c 63 20 14 addc r3,r3,r4
304: 7c 63 01 94 addze r3,r3
308: 4e 80 00 20 blr
Seems like only powerpc benefits from a branchless implementation.
Other main architectures like ARM or X86 get better code with
the generic implementation and its branch.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back when tcp_tso_autosize() and TCP pacing were introduced,
our focus was really to reduce burst sizes for long distance
flows.
The simple heuristic of using sk_pacing_rate/1024 has worked
well, but can lead to too small packets for hosts in the same
rack/cluster, when thousands of flows compete for the bottleneck.
Neal Cardwell had the idea of making the TSO burst size
a function of both sk_pacing_rate and tcp_min_rtt()
Indeed, for local flows, sending bigger bursts is better
to reduce cpu costs, as occasional losses can be repaired
quite fast.
This patch is based on Neal Cardwell implementation
done more than two years ago.
bbr is adjusting max_pacing_rate based on measured bandwidth,
while cubic would over estimate max_pacing_rate.
/proc/sys/net/ipv4/tcp_tso_rtt_log can be used to tune or disable
this new feature, in logarithmic steps.
Tested:
100Gbit NIC, two hosts in the same rack, 4K MTU.
600 flows rate-limited to 20000000 bytes per second.
Before patch: (TSO sizes would be limited to 20000000/1024/4096 -> 4 segments per TSO)
~# echo 0 >/proc/sys/net/ipv4/tcp_tso_rtt_log
~# nstat -n;perf stat ./super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000;nstat|egrep "TcpInSegs|TcpOutSegs|TcpRetransSegs|Delivered"
96005
Performance counter stats for './super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000':
65,945.29 msec task-clock # 2.845 CPUs utilized
1,314,632 context-switches # 19935.279 M/sec
5,292 cpu-migrations # 80.249 M/sec
940,641 page-faults # 14264.023 M/sec
201,117,030,926 cycles # 3049769.216 GHz (83.45%)
17,699,435,405 stalled-cycles-frontend # 8.80% frontend cycles idle (83.48%)
136,584,015,071 stalled-cycles-backend # 67.91% backend cycles idle (83.44%)
53,809,530,436 instructions # 0.27 insn per cycle
# 2.54 stalled cycles per insn (83.36%)
9,062,315,523 branches # 137422329.563 M/sec (83.22%)
153,008,621 branch-misses # 1.69% of all branches (83.32%)
23.182970846 seconds time elapsed
TcpInSegs 15648792 0.0
TcpOutSegs 58659110 0.0 # Average of 3.7 4K segments per TSO packet
TcpExtTCPDelivered 58654791 0.0
TcpExtTCPDeliveredCE 19 0.0
After patch:
~# echo 9 >/proc/sys/net/ipv4/tcp_tso_rtt_log
~# nstat -n;perf stat ./super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000;nstat|egrep "TcpInSegs|TcpOutSegs|TcpRetransSegs|Delivered"
96046
Performance counter stats for './super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000':
48,982.58 msec task-clock # 2.104 CPUs utilized
186,014 context-switches # 3797.599 M/sec
3,109 cpu-migrations # 63.472 M/sec
941,180 page-faults # 19214.814 M/sec
153,459,763,868 cycles # 3132982.807 GHz (83.56%)
12,069,861,356 stalled-cycles-frontend # 7.87% frontend cycles idle (83.32%)
120,485,917,953 stalled-cycles-backend # 78.51% backend cycles idle (83.24%)
36,803,672,106 instructions # 0.24 insn per cycle
# 3.27 stalled cycles per insn (83.18%)
5,947,266,275 branches # 121417383.427 M/sec (83.64%)
87,984,616 branch-misses # 1.48% of all branches (83.43%)
23.281200256 seconds time elapsed
TcpInSegs 1434706 0.0
TcpOutSegs 58883378 0.0 # Average of 41 4K segments per TSO packet
TcpExtTCPDelivered 58878971 0.0
TcpExtTCPDeliveredCE 9664 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20220309015757.2532973-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Having the definitions of {__,}tls_driver_ctx() under an #if
guard means code referencing them also needs to rely on the
preprocessor. The protection doesn't appear needed so make the
definitions unconditional.
Fixes: db37bc177d ("net/funeth: add the data path")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When CONFIG_TCP_MD5SIG isn't enabled, there is a compilation bug due to
the fact that the static inline definition of tcp_inbound_md5_hash() has
an unexpected semicolon. Remove it.
Fixes: 1330b6ef33 ("skb: make drop reason booleanable")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220309122012.668986-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Steffen Klassert says:
====================
pull request (net): ipsec 2022-03-09
1) Fix IPv6 PMTU discovery for xfrm interfaces.
From Lina Wang.
2) Revert failing for policies and states that are
configured with XFRMA_IF_ID 0. It broke a
user configuration. From Kai Lueke.
3) Fix a possible buffer overflow in the ESP output path.
4) Fix ESP GSO for tunnel and BEET mode on inter address
family tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a number of cases where function returns drop/no drop
decision as a boolean. Now that we want to report the reason
code as well we have to pass extra output arguments.
We can make the reason code evaluate correctly as bool.
I believe we're good to reorder the reasons as they are
reported to user space as strings.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix driver declares FDB isolation but puts all standalone ports in
VID 0. This is mostly problem-free as discussed with Alvin here:
https://patchwork.kernel.org/project/netdevbpf/cover/20220302191417.1288145-1-vladimir.oltean@nxp.com/#24763870
however there is one catch. DSA still thinks that FDB entries are
installed on the CPU port as many times as there are user ports, and
this is problematic when multiple user ports share the same MAC address.
Consider the default case where all user ports inherit their MAC address
from the DSA master, and then the user runs:
ip link set swp0 address 00:01:02:03:04:05
The above will make dsa_slave_set_mac_address() call
dsa_port_standalone_host_fdb_add() for 00:01:02:03:04:05 in port 0's
standalone database, and dsa_port_standalone_host_fdb_del() for the old
address of swp0, again in swp0's standalone database.
Both the ->port_fdb_add() and ->port_fdb_del() will be propagated down
to the felix driver, which will end up deleting the old MAC address from
the CPU port. But this is still in use by other user ports, so we end up
breaking unicast termination for them.
There isn't a problem in the fact that DSA keeps track of host
standalone addresses in the individual database of each user port: some
drivers like sja1105 need this. There also isn't a problem in the fact
that some drivers choose the same VID/FID for all standalone ports.
It is just that the deletion of these host addresses must be delayed
until they are known to not be in use any longer, and only the driver
has this knowledge. Since DSA keeps these addresses in &cpu_dp->fdbs and
&cpu_db->mdbs, it is just a matter of walking over those lists and see
whether the same MAC address is present on the CPU port in the port db
of another user port.
I have considered reusing the generic dsa_port_walk_fdbs() and
dsa_port_walk_mdbs() schemes for this, but locking makes it difficult.
In the ->port_fdb_add() method and co, &dp->addr_lists_lock is held, but
dsa_port_walk_fdbs() also acquires that lock. Also, even assuming that
we introduce an unlocked variant of the address iterator, we'd still
need some relatively complex data structures, and a void *ctx in the
dsa_fdb_walk_cb_t which we don't currently pass, such that drivers are
able to figure out, after iterating, whether the same MAC address is or
isn't present in the port db of another port.
All the above, plus the fact that I expect other drivers to follow the
same model as felix where all standalone ports use the same FID, made me
conclude that a generic method provided by DSA is necessary:
dsa_fdb_present_in_other_db() and the mdb equivalent. Felix calls this
from the ->port_fdb_del() handler for the CPU port, when the database
was classified to either a port db, or a LAG db.
For symmetry, we also call this from ->port_fdb_add(), because if the
address was installed once, then installing it a second time serves no
purpose: it's already in hardware in VID 0 and it affects all standalone
ports.
This change moves dsa_db_equal() from switch.c to dsa.c, since it now
has one more caller.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was a prerequisite for the ill-fated
"netfilter: nat: force port remap to prevent shadowing well-known ports".
As this has been reverted, this change can be backed out too.
Signed-off-by: Florian Westphal <fw@strlen.de>
The maximum message size that can be send is bigger than
the maximum site that skb_page_frag_refill can allocate.
So it is possible to write beyond the allocated buffer.
Fix this by doing a fallback to COW in that case.
v2:
Avoid get get_order() costs as suggested by Linus Torvalds.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a ("esp6: Avoid skb_cow_data whenever possible")
Reported-by: valis <sec@valis.email>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Realtek switches supports the same tag both before ethertype or between
payload and the CRC.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes attemting to print hdev->name directly which causes them to
print an error:
kernel: read_version:367: (efault): sock 000000006a3008f2
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members" for these cases. The older
style of one-element or zero-length arrays should no longer be used.
Reference:
https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
While investigating on why a synchronize_net() has been added recently
in ipv6_mc_down(), I found that igmp6_event_query() and igmp6_event_report()
might drop skbs in some cases.
Discussion about removing synchronize_net() from ipv6_mc_down()
will happen in a different thread.
Fixes: f185de28d9 ("mld: add new workqueues for process mld events")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220303173728.937869-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A latter patch will postpone the delivery_time clearing until the stack
knows the skb is being delivered locally. That will allow other kernel
forwarding path (e.g. ip[6]_forward) to keep the delivery_time also.
An earlier attempt was to do skb_clear_delivery_time() in
ip_local_deliver() and ip6_input(). The discussion [0] requested
to move it one step later into ip_local_deliver_finish()
and ip6_input_finish() so that the delivery_time can be kept
for the ip_vs forwarding path also.
To do that, this patch also needs to take care of the (rcv) timestamp
usecase in ip_is_fragment(). It needs to expect delivery_time in
the skb->tstamp, so it needs to save the mono_delivery_time bit in
inet_frag_queue such that the delivery_time (if any) can be restored
in the final defragmented skb.
[Note that it will only happen when the locally generated skb is looping
from egress to ingress over a virtual interface (e.g. veth, loopback...),
skb->tstamp may have the delivery time before it is known that it will
be delivered locally and received by another sk.]
[0]: https://lore.kernel.org/netdev/ca728d81-80e8-3767-d5e-d44f6ad96e43@ssi.bg/
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ocelot" and "ocelot-8021q" tagging protocols make use of different
hardware resources, and host FDB entries have different destination
ports in the switch analyzer module, practically speaking.
So when the user requests a tagging protocol change, the driver must
migrate all host FDB and MDB entries from the NPI port (in fact CPU port
module) towards the same physical port, but this time used as a regular
port.
It is pointless for the felix driver to keep a copy of the host
addresses, when we can create and export DSA helpers for walking through
the addresses that it already needs to keep on the CPU port, for
refcounting purposes.
felix_classify_db() is moved up to avoid a forward declaration.
We pass "bool change" because dp->fdbs and dp->mdbs are uninitialized
lists when felix_setup() first calls felix_set_tag_protocol(), so we
need to avoid calling dsa_port_walk_fdbs() during probe time.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a function page_pool_get_stats which can be used by drivers to obtain
stats for a specified page_pool.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add per-cpu stats tracking page pool recycling events:
- cached: recycling placed page in the page pool cache
- cache_full: page pool cache was full
- ring: page placed into the ptr ring
- ring_full: page released from page pool because the ptr ring was full
- released_refcnt: page released (and not recycled) because refcnt > 1
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add per-pool statistics counters for the allocation path of a page pool.
These stats are incremented in softirq context, so no locking or per-cpu
variables are needed.
This code is disabled by default and a kernel config option is provided for
users who wish to enable them.
The statistics added are:
- fast: successful fast path allocations
- slow: slow path order-0 allocations
- slow_high_order: slow path high order allocations
- empty: ptr ring is empty, so a slow path allocation was forced.
- refill: an allocation which triggered a refill of the cache
- waive: pages obtained from the ptr ring that cannot be added to
the cache due to a NUMA mismatch.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Use kfree_rcu(ptr, rcu) variant, using kfree_rcu(ptr) was not
intentional. From Eric Dumazet.
2) Use-after-free in netfilter hook core, from Eric Dumazet.
3) Missing rcu read lock side for netfilter egress hook,
from Florian Westphal.
4) nf_queue assume state->sk is full socket while it might not be.
Invoke sock_gen_put(), from Florian Westphal.
5) Add selftest to exercise the reported KASAN splat in 4)
6) Fix possible use-after-free in nf_queue in case sk_refcnt is 0.
Also from Florian.
7) Use input interface index only for hardware offload, not for
the software plane. This breaks tc ct action. Patch from Paul Blakey.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
net/sched: act_ct: Fix flow table lookup failure with no originating ifindex
netfilter: nf_queue: handle socket prefetch
netfilter: nf_queue: fix possible use-after-free
selftests: netfilter: add nfqueue TCP_NEW_SYN_RECV socket race test
netfilter: nf_queue: don't assume sk is full socket
netfilter: egress: silence egress hook lockdep splats
netfilter: fix use-after-free in __nf_register_net_hook()
netfilter: nf_tables: prefer kfree_rcu(ptr, rcu) variant
====================
Link: https://lore.kernel.org/r/20220301215337.378405-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After cited commit optimizted hw insertion, flow table entries are
populated with ifindex information which was intended to only be used
for HW offload. This tuple ifindex is hashed in the flow table key, so
it must be filled for lookup to be successful. But tuple ifindex is only
relevant for the netfilter flowtables (nft), so it's not filled in
act_ct flow table lookup, resulting in lookup failure, and no SW
offload and no offload teardown for TCP connection FIN/RST packets.
To fix this, add new tc ifindex field to tuple, which will
only be used for offloading, not for lookup, as it will not be
part of the tuple hash.
Fixes: 9795ded7f9 ("net/sched: act_ct: Fill offloading tuple iifidx")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This add a new sysctl: net.smc.autocorking_size
We can dynamically change the behaviour of autocorking
by change the value of autocorking_size.
Setting to 0 disables autocorking in SMC
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add sysctl interface to support container environment
for SMC as we talk in the mail list.
Link: https://lore.kernel.org/netdev/20220224020253.GF5443@linux.alibaba.com
Co-developed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
The sock_hold() side seems suspect, because there is no guarantee
that sk_refcnt is not already 0.
On failure, we cannot queue the packet and need to indicate an
error. The packet will be dropped by the caller.
v2: split skb prefetch hunk into separate change
Fixes: 271b72c7fa ("udp: RCU handling for Unicast packets.")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Add per-vni statistics for vni filter mode. Counting Rx/Tx
bytes/packets/drops/errors at the appropriate places.
This patch changes vxlan_vs_find_vni to also return the
vxlan_vni_node in cases where the vni belongs to a vni
filtering vxlan device
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds vnifiltering support to collect metadata device.
Motivation:
You can only use a single vxlan collect metadata device for a given
vxlan udp port in the system today. The vxlan collect metadata device
terminates all received vxlan packets. As shown in the below diagram,
there are use-cases where you need to support multiple such vxlan devices in
independent bridge domains. Each vxlan device must terminate the vni's
it is configured for.
Example usecase: In a service provider network a service provider
typically supports multiple bridge domains with overlapping vlans.
One bridge domain per customer. Vlans in each bridge domain are
mapped to globally unique vxlan ranges assigned to each customer.
vnifiltering support in collect metadata devices terminates only configured
vnis. This is similar to vlan filtering in bridge driver. The vni filtering
capability is provided by a new flag on collect metadata device.
In the below pic:
- customer1 is mapped to br1 bridge domain
- customer2 is mapped to br2 bridge domain
- customer1 vlan 10-11 is mapped to vni 1001-1002
- customer2 vlan 10-11 is mapped to vni 2001-2002
- br1 and br2 are vlan filtering bridges
- vxlan1 and vxlan2 are collect metadata devices with
vnifiltering enabled
┌──────────────────────────────────────────────────────────────────┐
│ switch │
│ │
│ ┌───────────┐ ┌───────────┐ │
│ │ │ │ │ │
│ │ br1 │ │ br2 │ │
│ └┬─────────┬┘ └──┬───────┬┘ │
│ vlans│ │ vlans │ │ │
│ 10,11│ │ 10,11│ │ │
│ │ vlanvnimap: │ vlanvnimap: │
│ │ 10-1001,11-1002 │ 10-2001,11-2002 │
│ │ │ │ │ │
│ ┌──────┴┐ ┌──┴─────────┐ ┌───┴────┐ │ │
│ │ swp1 │ │vxlan1 │ │ swp2 │ ┌┴─────────────┐ │
│ │ │ │ vnifilter:│ │ │ │vxlan2 │ │
│ └───┬───┘ │ 1001,1002│ └───┬────┘ │ vnifilter: │ │
│ │ └────────────┘ │ │ 2001,2002 │ │
│ │ │ └──────────────┘ │
│ │ │ │
└───────┼──────────────────────────────────┼───────────────────────┘
│ │
│ │
┌─────┴───────┐ │
│ customer1 │ ┌─────┴──────┐
│ host/VM │ │customer2 │
└─────────────┘ │ host/VM │
└────────────┘
With this implementation, vxlan dst metadata device can
be associated with range of vnis.
struct vxlan_vni_node is introduced to represent
a configured vni. We start with vni and its
associated remote_ip in this structure. This
structure can be extended to bring in other
per vni attributes if there are usecases for it.
A vni inherits an attribute from the base vxlan device
if there is no per vni attributes defined.
struct vxlan_dev gets a new rhashtable for
vnis called vxlan_vni_group. vxlan_vnifilter.c
implements the necessary netlink api, notifications
and helper functions to process and manage lifecycle
of vxlan_vni_node.
This patch also adds new helper functions in vxlan_multicast.c
to handle per vni remote_ip multicast groups which are part
of vxlan_vni_group.
Fix build problems:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As more police parameters are passed to flow_offload, driver can check
them to make sure hardware handles packets in the way indicated by tc.
The conform-exceed control should be drop/pipe or drop/ok. Besides,
for drop/ok, the police should be the last action. As hardware can't
configure peakrate/avrate/overhead, offload should not be supported if
any of them is configured.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current police offload action entry is missing exceed/notexceed
actions and parameters that can be configured by tc police action.
Add the missing parameters as a pre-step for offloading police actions
to hardware.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As FDB isolation cannot be enforced between VLAN-aware bridges in lack
of hardware assistance like extra FID bits, it seems plausible that many
DSA switches cannot do it. Therefore, they need to reject configurations
with multiple VLAN-aware bridges from the two code paths that can
transition towards that state:
- joining a VLAN-aware bridge
- toggling VLAN awareness on an existing bridge
The .port_vlan_filtering method already propagates the netlink extack to
the driver, let's propagate it from .port_bridge_join too, to make sure
that the driver can use the same function for both.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DSA, to encourage drivers to perform FDB isolation simply means to
track which bridge does each FDB and MDB entry belong to. It then
becomes the driver responsibility to use something that makes the FDB
entry from one bridge not match the FDB lookup of ports from other
bridges.
The top-level functions where the bridge is determined are:
- dsa_port_fdb_{add,del}
- dsa_port_host_fdb_{add,del}
- dsa_port_mdb_{add,del}
- dsa_port_host_mdb_{add,del}
aka the pre-crosschip-notifier functions.
Changing the API to pass a reference to a bridge is not superfluous, and
looking at the passed bridge argument is not the same as having the
driver look at dsa_to_port(ds, port)->bridge from the ->port_fdb_add()
method.
DSA installs FDB and MDB entries on shared (CPU and DSA) ports as well,
and those do not have any dp->bridge information to retrieve, because
they are not in any bridge - they are merely the pipes that serve the
user ports that are in one or multiple bridges.
The struct dsa_bridge associated with each FDB/MDB entry is encapsulated
in a larger "struct dsa_db" database. Although only databases associated
to bridges are notified for now, this API will be the starting point for
implementing IFF_UNICAST_FLT in DSA. There, the idea is to install FDB
entries on the CPU port which belong to the corresponding user port's
port database. These are supposed to match only when the port is
standalone.
It is better to introduce the API in its expected final form than to
introduce it for bridges first, then to have to change drivers which may
have made one or more assumptions.
Drivers can use the provided bridge.num, but they can also use a
different numbering scheme that is more convenient.
DSA must perform refcounting on the CPU and DSA ports by also taking
into account the bridge number. So if two bridges request the same local
address, DSA must notify the driver twice, once for each bridge.
In fact, if the driver supports FDB isolation, DSA must perform
refcounting per bridge, but if the driver doesn't, DSA must refcount
host addresses across all bridges, otherwise it would be telling the
driver to delete an FDB entry for a bridge and the driver would delete
it for all bridges. So introduce a bool fdb_isolation in drivers which
would make all bridge databases passed to the cross-chip notifier have
the same number (0). This makes dsa_mac_addr_find() -> dsa_db_equal()
say that all bridge databases are the same database - which is
essentially the legacy behavior.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
1) Fix PMTU for IPv6 if the reported MTU minus the ESP overhead is
smaller than 1280. From Jiri Bohac.
2) Fix xfrm interface ID and inter address family tunneling when
migrating xfrm states. From Yan Yan.
3) Add missing xfrm intrerface ID initialization on xfrmi_changelink.
From Antony Antony.
4) Enforce validity of xfrm offload input flags so that userspace can't
send undefined flags to the offload driver.
From Leon Romanovsky.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Waldekranz