Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Temperature is measured in tenths of degree Celsius.
Fixes: 085bc24d15 ("Add LTC2941/LTC2943 Battery Gauge Driver")
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add properties for charge empty and charge full thresholds.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The driver sets the fuel gauge to continuous monitoring on startup, for
the models that support this. When the board shuts down, the chip remains
in that mode, causing a few mA drain on the battery every 2 or 10 seconds.
This patch registers a shutdown handler that turns off the monitoring to
prevent this battery drain.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
LTC2944 is compatible with LTC2943, but uses different
voltage and current computing constants.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
LTC2942 is pin compatible with LTC2941 providing additional
informations about battery voltage and temperature. It can
be runtime detected using bit A7 in the Status register.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Dragos Bogdan <dragos.bogdan@analog.com>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
In order to support LTC2942 which has temperature registers
at different offsets than LTC2943 use following register naming
scheme (prefixes):
- LTC294X_ common registers
- LTC2942_ chips specific registers
- LTC2943_ specific registers
LTC2944 is compatible with LTC2943 but uses different constants
to compute voltage and current, so replace num_regs misused
for device indentification with real device id to discriminate
between those two.
There are no functional changes.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Dragos Bogdan <dragos.bogdan@analog.com>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This moves all power supply drivers from drivers/power/
to drivers/power/supply/. The intention is a cleaner
source tree, since drivers/power/ also contains frameworks
unrelated to power supply, like adaptive voltage scaling.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Thomas Gleixner