pit_expect_msb() returns success wrongly in the below SMI scenario:
a. pit_verify_msb() has not yet seen the MSB transition.
b. we are close to the MSB transition though and got a SMI immediately after
returning from pit_verify_msb() which didn't see the MSB transition. PIT MSB
transition has happened somewhere during SMI execution.
c. returned from SMI and we noted down the 'tsc', saw the pit MSB change now and
exited the loop to calculate 'deltatsc'. Instead of noting the TSC at the MSB
transition, we are way off because of the SMI. And as the SMI happened
between the pit_verify_msb() and before the 'tsc' is recorded in the
for loop, 'delattsc' (d1/d2 in quick_pit_calibrate()) will be small and
quick_pit_calibrate() will not notice this error.
Depending on whether SMI disturbance happens while computing d1 or d2, we will
see the TSC calibrated value smaller or bigger than the expected value. As a
result, in a cluster we were seeing a variation of approximately +/- 20MHz in
the calibrated values, resulting in NTP failures.
[ As far as the SMI source is concerned, this is a periodic SMI that gets
disabled after ACPI is enabled by the OS. But the TSC calibration happens
before the ACPI is enabled. ]
To address this, change pit_expect_msb() so that
- the 'tsc' is the TSC in between the two reads that read the MSB
change from the PIT (same as before)
- the 'delta' is the difference in TSC from *before* the MSB changed
to *after* the MSB changed.
Now the delta is twice as big as before (it covers four PIT accesses,
roughly 4us) and quick_pit_calibrate() will loop a bit longer to get
the calibrated value with in the 500ppm precision. As the delta (d1/d2)
covers four PIT accesses, actual calibrated result might be closer to
250ppm precision.
As the loop now takes longer to stabilize, double MAX_QUICK_PIT_MS to 50.
SMI disturbance will showup as much larger delta's and the loop will take
longer than usual for the result to be with in the accepted precision. Or will
fallback to slow PIT calibration if it takes more than 50msec.
Also while we are at this, remove the calibration correction that aims to
get the result to the middle of the error bars. We really don't know which
direction to correct into, so remove it.
Reported-and-tested-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1326843337.5291.4.camel@sbsiddha-mobl2
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch provides functionality to audit system call events on the
ARM platform. The implementation was based off the structure of the
MIPS platform and information in this
(http://lists.fedoraproject.org/pipermail/arm/2009-October/000382.html)
mailing list thread. The required audit_syscall_exit and
audit_syscall_entry checks were added to ptrace using the standard
registers for system call values (r0 through r3). A thread information
flag was added for auditing (TIF_SYSCALL_AUDIT) and a meta-flag was
added (_TIF_SYSCALL_WORK) to simplify modifications to the syscall
entry/exit. Now, if either the TRACE flag is set or the AUDIT flag is
set, the syscall_trace function will be executed. The prober changes
were made to Kconfig to allow CONFIG_AUDITSYSCALL to be enabled.
Due to platform availability limitations, this patch was only tested
on the Android platform running the modified "android-goldfish-2.6.29"
kernel. A test compile was performed using Code Sourcery's
cross-compilation toolset and the current linux-3.0 stable kernel. The
changes compile without error. I'm hoping, due to the simple modifications,
the patch is "obviously correct".
Signed-off-by: Nathaniel Husted <nhusted@gmail.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Every arch calls:
if (unlikely(current->audit_context))
audit_syscall_entry()
which requires knowledge about audit (the existance of audit_context) in
the arch code. Just do it all in static inline in audit.h so that arch's
can remain blissfully ignorant.
Signed-off-by: Eric Paris <eparis@redhat.com>
In the ia32entry syscall exit audit fastpath we have assembly code which calls
__audit_syscall_exit directly. This code was, however, zeroes the upper 32
bits of the return code. It then proceeded to call code which expects longs
to be 64bits long. In order to handle code which expects longs to be 64bit we
sign extend the return code if that code is an error. Thus the
__audit_syscall_exit function can correctly handle using the values in
snprintf("%ld"). This fixes the regression introduced in 5cbf1565f2.
Old record:
type=SYSCALL msg=audit(1306197182.256:281): arch=40000003 syscall=192 success=no exit=4294967283
New record:
type=SYSCALL msg=audit(1306197182.256:281): arch=40000003 syscall=192 success=no exit=-13
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
The audit system previously expected arches calling to audit_syscall_exit to
supply as arguments if the syscall was a success and what the return code was.
Audit also provides a helper AUDITSC_RESULT which was supposed to simplify things
by converting from negative retcodes to an audit internal magic value stating
success or failure. This helper was wrong and could indicate that a valid
pointer returned to userspace was a failed syscall. The fix is to fix the
layering foolishness. We now pass audit_syscall_exit a struct pt_reg and it
in turns calls back into arch code to collect the return value and to
determine if the syscall was a success or failure. We also define a generic
is_syscall_success() macro which determines success/failure based on if the
value is < -MAX_ERRNO. This works for arches like x86 which do not use a
separate mechanism to indicate syscall failure.
We make both the is_syscall_success() and regs_return_value() static inlines
instead of macros. The reason is because the audit function must take a void*
for the regs. (uml calls theirs struct uml_pt_regs instead of just struct
pt_regs so audit_syscall_exit can't take a struct pt_regs). Since the audit
function takes a void* we need to use static inlines to cast it back to the
arch correct structure to dereference it.
The other major change is that on some arches, like ia64, MIPS and ppc, we
change regs_return_value() to give us the negative value on syscall failure.
THE only other user of this macro, kretprobe_example.c, won't notice and it
makes the value signed consistently for the audit functions across all archs.
In arch/sh/kernel/ptrace_64.c I see that we were using regs[9] in the old
audit code as the return value. But the ptrace_64.h code defined the macro
regs_return_value() as regs[3]. I have no idea which one is correct, but this
patch now uses the regs_return_value() function, so it now uses regs[3].
For powerpc we previously used regs->result but now use the
regs_return_value() function which uses regs->gprs[3]. regs->gprs[3] is
always positive so the regs_return_value(), much like ia64 makes it negative
before calling the audit code when appropriate.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com> [for x86 portion]
Acked-by: Tony Luck <tony.luck@intel.com> [for ia64]
Acked-by: Richard Weinberger <richard@nod.at> [for uml]
Acked-by: David S. Miller <davem@davemloft.net> [for sparc]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [for mips]
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> [for ppc]
The Intel documentation at
http://software.intel.com/file/36945
shows the ANDN opcode and Group 17 with encoding f2 and f3 encoding
respectively. The current version of x86-opcode-map.txt shows them
with f3 and f4. Unless someone can point to documentation which shows
the currently used encoding the following patch be applied.
Signed-off-by: Ulrich Drepper <drepper@gmail.com>
Link: http://lkml.kernel.org/r/CAOPLpQdq5SuVo9=023CYhbFLAX9rONyjmYq7jJkqc5xwctW5eA@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current linux-next compiled with mpc85xx_defconfig causes this:
arch/powerpc/platforms/85xx/p1022_ds.c:341:14: error: 'udbg_progress' undeclared here (not in a function)
Add include to fix this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the ZONE_DMA kconfig symbol under a menu item instead
of having it listed before everything else in
"make {xconfig | gconfig | nconfig | menuconfig}".
This drops the first line of the top-level kernel config menu
(in 3.2) below and moves it under "Processor type and features".
[*] DMA memory allocation support
General setup --->
[*] Enable loadable module support --->
[*] Enable the block layer --->
Processor type and features --->
Power management and ACPI options --->
Bus options (PCI etc.) --->
Executable file formats / Emulations --->
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-mm@kvack.org <linux-mm@kvack.org>
Link: http://lkml.kernel.org/r/4F14811E.6090107@xenotime.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: David Rientjes <rientjes@google.com>
In SRAT v1, we had 8bit proximity domain (PXM) fields; SRAT v2 provides
32bits for these. The new fields were reserved before.
According to the ACPI spec, the OS must disregrard reserved fields.
ia64 did handle the PXM fields almost consistently, but depending on
sgi's sn2 platform. This patch leaves the sn2 logic in, but does also
use 16/32 bits for PXM if the SRAT has rev 2 or higher.
The patch also adds __init to the two pxm accessor functions, as they
access __initdata now and are called from an __init function only anyway.
Note that the code only uses 16 bits for the PXM field in the processor
proximity field; the patch does not address this as 16 bits are more than
enough.
Signed-off-by: Kurt Garloff <kurt@garloff.de>
Signed-off-by: Len Brown <len.brown@intel.com>
In SRAT v1, we had 8bit proximity domain (PXM) fields; SRAT v2 provides
32bits for these. The new fields were reserved before.
According to the ACPI spec, the OS must disregrard reserved fields.
x86/x86-64 was rather inconsistent prior to this patch; it used 8 bits
for the pxm field in cpu_affinity, but 32 bits in mem_affinity.
This patch makes it consistent: Either use 8 bits consistently (SRAT
rev 1 or lower) or 32 bits (SRAT rev 2 or higher).
cc: x86@kernel.org
Signed-off-by: Kurt Garloff <kurt@garloff.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some firmware will access memory in ACPI NVS region via APEI. That
is, instructions in APEI ERST/EINJ table will read/write ACPI NVS
region. The original resource conflict checking in APEI code will
check memory/ioport accessed by APEI via general resource management
mechanism. But ACPI NVS region is marked as busy already, so that the
false resource conflict will prevent APEI ERST/EINJ to work.
To fix this, this patch record ACPI NVS regions, so that we can avoid
request resources for memory region inside it.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds separate accounting of UV2 message "strong
nack's" in the BAU statistics.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116212238.GF5767@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch moves the ack of the BAU interrupt to the beginning
of the interrupt handler so that there is less possibility of a
lost interrupt and slower response to a shootdown message.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116212146.GE5767@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch removes an unnecessary test for a
no-destination-resources-available condition that looks like a
destination timeout in UV1, but is separately distinguishable in
UV2.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116212050.GD5767@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch implements a workaround for a UV2 hardware bug.
The bug is a non-atomic update of a memory-mapped register. When
hardware message delivery and software message acknowledge occur
simultaneously the pending message acknowledge for the arriving
message may be lost. This causes the sender's message status to
stay busy.
Part of the workaround is to not acknowledge a completed message
until it is verified that no other message is actually using the
resource that is mistakenly recorded in the completed message.
Part of the workaround is to test for long elapsed time in such
a busy condition, then handle it by using a spare sending
descriptor. The stay-busy condition is eventually timed out by
hardware, and then the original sending descriptor can be
re-used. Most of that logic change is in keeping track of the
current descriptor and the state of the spares.
The occurrences of the workaround are added to the BAU
statistics.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116211947.GC5767@sgi.com
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the call to enable_timeouts() forward so that
BAU_MISC_CONTROL is initialized before using it in
calculate_destination_timeout().
Fix the calculation of a BAU destination timeout
for UV2 (in calculate_destination_timeout()).
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116211848.GB5767@sgi.com
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update the use of the Broadcast Assist Unit on SGI Altix UV2 to
the use of native UV2 mode on new hardware (not the legacy mode).
UV2 native mode has a different format for a broadcast message.
We also need quick differentiaton between UV1 and UV2.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120116211750.GA5767@sgi.com
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Invert VCLK polarity for framebuffer on ORIGEN
ARM: S3C64XX: Fix interrupt configuration for PCA935x on Cragganmore
ARM: S3C64XX: Fix the memory mapped GPIOs on Cragganmore
ARM: S3C64XX: Remove hsmmc1 from Cragganmore
ARM: S3C64XX: Remove unconditional power domain disables
ARM: SAMSUNG: Declare struct platform_device in plat/s3c64xx-spi.h
ARM: SAMSUNG: dma-ops.h needs mach/dma.h
ARM: SAMSUNG: Guard against multiple inclusion of plat/dma.h
* 'x86-syscall-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Move <asm/asm-offsets.h> from trace_syscalls.c to asm/syscall.h
x86, um: Fix typo in 32-bit system call modifications
um: Use $(srctree) not $(KBUILD_SRC)
x86, um: Mark system call tables readonly
x86, um: Use the same style generated syscall tables as native
um: Generate headers before generating user-offsets.s
um: Run host archheaders, allow use of host generated headers
kbuild, headers.sh: Don't make archheaders explicitly
x86, syscall: Allow syscall offset to be symbolic
x86, syscall: Re-fix typo in comment
x86: Simplify syscallhdr.sh
x86: Generate system call tables and unistd_*.h from tables
checksyscalls: Use arch/x86/syscalls/syscall_32.tbl as source
x86: Machine-readable syscall tables and scripts to process them
trace: Include <asm/asm-offsets.h> in trace_syscalls.c
x86-64, ia32: Move compat_ni_syscall into C and its own file
x86-64, syscall: Adjust comment spacing and remove typo
kbuild: Add support for an "archheaders" target
kbuild: Add support for installing generated asm headers
When suspending, there was a large list of warnings going something like:
Device 'machinecheck1' does not have a release() function, it is broken and must be fixed
This patch turns the static mce_devices into dynamically allocated, and
properly frees them when they are removed from the system. It solves
the warning messages on my laptop here.
Reported-by: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Djalal Harouni <tixxdz@opendz.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@amd64.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-arm:
ARM: sa11x0: assabet: fix build warning
ARM: Add arm_memblock_steal() to allocate memory away from the kernel
ARM: 7275/1: LPAE: Check the CPU support for the long descriptor format
ARM: 7274/1: NUC900: Rename nuc900-audio platform device to nuc900-ac97
ARM: 7272/1: S3C24XX: Fix build error for missing <mach/system-reset.h>
ARM: 7271/1: Fix typo in conversion of ARCH_NR_GPIOS to Kconfig
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Hibernate: Drop the check of swap space size for compressed image
PM / shmobile: fix A3SP suspend method
PM / Domains: Skip governor functions for CONFIG_PM_RUNTIME unset
PM / Domains: Fix build for CONFIG_PM_SLEEP unset
PM: Make sysrq-o be available for CONFIG_PM unset
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Kbuild: Use dtc's -d (dependency) option
dtc: Implement -d option to write out a dependency file
kbuild: Fix comment in Makefile.lib
scripts/genksyms: clean lex/yacc generated files
kbuild: Correctly deal with make options which contain an "s"
Since a32618d2 (ARM: pgtable: switch to use pgtable-nopud.h), assabet
warns as follows:
arch/arm/mach-sa1100/assabet.c: In function 'map_sa1100_gpio_regs':
arch/arm/mach-sa1100/assabet.c:264: warning: passing argument 1 of 'pmd_offset' from incompatible pointer type
Fix this by adding the necessary pud_offset() macro.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
BSYM macro is only needed for assembly files and its usage in c files is
wrong, so only define it for assembly.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Dave Martin <dave.martin@linaro.org>
BSYM macro is only needed for assembly files and its usage in c files is
wrong, so remove it. The linker will correctly set bit 0 for Thumb2
kernels.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Dave Martin <dave.martin@linaro.org>
BSYM macro is only needed for assembly files and its usage in c files is
wrong, so remove it. The linker will correctly set bit 0 for Thumb2
kernels.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
BSYM macro is only needed for assembly files and its usage in c files is
wrong, so remove it. The linker will correctly set bit 0 for Thumb2
kernels.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Dave Martin <dave.martin@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Once the ENDPROC is in place, BSYM() in not longer necessary
to get correct pointer to u8500_secondary_startup().
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Once the ENDPROC is in place, BSYM() in not longer necessary
to get correct pointer to msm_secondary_startup().
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Once the ENDPROC is in place, BSYM() in not longer necessary
to get correct pointer to versatile_secondary_startup().
Tested-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Dave Martin <dave.martin@linaro.org>
omap3isp depends on CONFIG_IOMMU_API, so avoid registering its
device (and defining its configuration structs) on !CONFIG_IOMMU_API.
This is generally nice to have, but more importantly, it fixes:
arch/arm/plat-omap/include/plat/iommu.h: In function 'dev_to_omap_iommu':
arch/arm/plat-omap/include/plat/iommu.h:135: error: 'struct
dev_archdata' has no member named 'iommu'
arch/arm/mach-omap2/devices.c: In function 'omap3_init_camera':
arch/arm/mach-omap2/devices.c:222: error: 'struct dev_archdata' has no
member named 'iommu'
make[1]: *** [arch/arm/mach-omap2/devices.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Which happens because while setting up the omap3isp device we try
to access the (now nonexistent) iommu member of dev_archdata.
Compile tested with omap2plus_defconfig on today's:
commit e343a895a9
Merge: 06792c4193a667
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue Jan 10 18:04:27 2012 -0800
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Reported-by: Govindraj Raja <govindraj.raja@ti.com>
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Joerg Roedel <Joerg.Roedel@amd.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This very noisy sparse warning appears on almost every file in
the kernel:
CHECK init/main.c
arch/x86/include/asm/thread_info.h:43:55: error: dubious one-bit
signed bitfield arch/x86/include/asm/thread_info.h:44:46: error:
dubious one-bit signed bitfield
Sparse is right and this patch changes sig_on_uaccess_error and
uaccess_err flags to unsigned type and thus fixes the warning.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Andy Lutomirski <luto@mit.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Dan Carpenter <error27@gmail.com>
Link: http://lkml.kernel.org/r/20120111011146.GA30428@oksana.dev.rtsoft.ru
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After compiling the kernel, I got:
% git status
# On branch master
# Untracked files:
# (use "git add <file>..." to include in what will be committed)
#
# arch/x86/tools/insn_sanity
nothing added to commit but untracked files present (use "git add" to track)
it should be added to .gitignore.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/1326628937-27609-1-git-send-email-xiyou.wangcong@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The arch/x86/lib/x86-opcode-map.txt file [used by the
kprobes instruction decoder] contains the line:
af: SCAS/W/D/Q rAX,Xv
This is what the Intel manuals show, but it's not correct.
The 'X' stands for:
Memory addressed by the DS:rSI register pair (for example, MOVS, CMPS, OUTS, or LODS).
On the other hand 'Y' means (also see the ae byte entry for
SCASB):
Memory addressed by the ES:rDI register pair (for example, MOVS, CMPS, INS, STOS, or SCAS).
Signed-off-by: Ulrich Drepper <drepper@gmail.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: yrl.pp-manager.tt@hitachi.com
Link: http://lkml.kernel.org/r/CAOPLpQfytPyDEBF1Hbkpo7ovUerEsstVGxBr%3DEpDL-BKEMaqLA@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
perf tools: Fix compile error on x86_64 Ubuntu
perf report: Fix --stdio output alignment when --showcpuutilization used
perf annotate: Get rid of field_sep check
perf annotate: Fix usage string
perf kmem: Fix a memory leak
perf kmem: Add missing closedir() calls
perf top: Add error message for EMFILE
perf test: Change type of '-v' option to INCR
perf script: Add missing closedir() calls
tracing: Fix compile error when static ftrace is enabled
recordmcount: Fix handling of elf64 big-endian objects.
perf tools: Add const.h to MANIFEST to make perf-tar-src-pkg work again
perf tools: Add support for guest/host-only profiling
perf kvm: Do guest-only counting by default
perf top: Don't update total_period on process_sample
perf hists: Stop using 'self' for struct hist_entry
perf hists: Rename total_session to total_period
x86: Add counter when debug stack is used with interrupts enabled
x86: Allow NMIs to hit breakpoints in i386
x86: Keep current stack in NMI breakpoints
...
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, atomic: atomic64_read() take a const pointer
x86, UV: Update Boot messages for SGI UV2 platform
* 'for-next' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: Split trivial #if defined(__KERNEL__) && X conditionals
UAPI: Don't have a #elif clause in a __KERNEL__ guard in linux/soundcard.h
UAPI: Fix AHZ multiple inclusion when __KERNEL__ is removed
UAPI: Make linux/patchkey.h easier to parse
UAPI: Fix nested __KERNEL__ guards in video/edid.h
UAPI: Alter the S390 asm include guards to be recognisable by the UAPI splitter
UAPI: Guard linux/cuda.h
UAPI: Guard linux/pmu.h
UAPI: Guard linux/isdn_divertif.h
UAPI: Guard linux/sound.h
UAPI: Rearrange definition of HZ in asm-generic/param.h
UAPI: Make FRV use asm-generic/param.h
UAPI: Make M32R use asm-generic/param.h
UAPI: Make MN10300 use asm-generic/param.h
UAPI: elf_read_implies_exec() is a kernel-only feature - so hide from userspace
UAPI: Don't include linux/compat.h in sparc's asm/siginfo.h
UAPI: Fix arch/mips/include/asm/Kbuild to have separate header-y lines
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (175 commits)
module_param: make bool parameters really bool (drivers/video/i810)
Revert "atmel_lcdfb: Adjust HFP calculation so it matches the manual."
OMAPDSS: HDMI: Disable DDC internal pull up
OMAPDSS: HDMI: Move duplicate code from boardfile
OMAPDSS: add OrtusTech COM43H4M10XTC display support
OMAP: DSS2: Support for UMSH-8173MD TFT panel
ASoC: OMAP: HDMI: Move HDMI codec trigger function to generic HDMI driver
OMAPDSS: HDMI: Create function to enable HDMI audio
ASoC: OMAP: HDMI: Correct signature of ASoC functions
ASoC: OMAP: HDMI: Introduce driver data for audio codec
grvga: fix section mismatch warnings
video: s3c-fb: Don't keep device runtime active when open
video: s3c-fb: Hold runtime PM references when touching registers
video: s3c-fb: Take a runtime PM reference when unblanked
video: s3c-fb: Disable runtime PM in error paths from probe
video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
video: s3c-fb: Make runtime PM functional again
drivers/video: fsl-diu-fb: merge fsl_diu_alloc() into map_video_memory()
drivers/video: fsl-diu-fb: add default platform ops functions
drivers/video: fsl-diu-fb: remove broken reference count enabling the display
...
This hooks dtc into Kbuild's dependency system.
Thus, for example, "make dtbs" will rebuild tegra-harmony.dtb if only
tegra20.dtsi has changed yet tegra-harmony.dts has not. The previous
lack of this feature recently caused me to have very confusing "git
bisect" results.
For ARM, it's obvious what to add to $(targets). I'm not familiar enough
with other architectures to know what to add there. Powerpc appears to
already add various .dtb files into $(targets), but the other archs may
need something added to $(targets) to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
[mmarek: Dropped arch/c6x part to avoid merging commits from the middle
of the merge window]
Signed-off-by: Michal Marek <mmarek@suse.cz>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPD2aFAAoJENkgDmzRrbjxNzsQAIeYbbrXYLjr6kQzUSngj/eC
FzjaTEfYTQIeuQCFJHcHthyc5lXV4sQbo3jOezW+Bp5yuDJL2aWIHesSfWZe7imu
zQdM4VshOYdAmUR9Q0AW5zhB8Smbs7/AyABiF2jm4p0ZPOuyMDSlei9sjvE9Vjvt
B7g5ht7L6kz0JbDnwwy0u5gs+tEitwpXYId9Y4ysZIBzIbL0qkPX8veOddGTMy0N
8xhWXaKtufpjvxFD2ORLDsw3AkoF1xXSNuFd/5nzCNpbeE7TW931jfkPoqJumuAO
7GLxcU9kKYl+IICobC6wBtsj/RrB7w+cBXMvPGwdBliam1qaRhUcJZi5FLM/Ha5d
2A9QDYNUpoXiO8JbPXrV9Z+Y0+Co8RilsQj7R/rjZh6AbbYCWt9nxzx2Svl/RfTr
xfiimHuB2P3rHjOvpCXULwOOuE5c8MzPuWncpdjiD3uGXOY/aY+X1m+if/quJw9D
grPlKL0+YiRakEYUeGG4M77KCqyKFZaF7L7UQPbqfZcj8V/9AW3/7U5I/B9RlAjs
idsr4fcf5s0N+oKUyTCW1ncpUDQNiwbU2NyJQqeu1ZxaRGj72AgyvsaNeyIPDyK+
f6x95Bi7i8KLjXc9Z1KvJwh2Nxt25gNUiTYVha/9H2NpJGd1cfI15kTOGXrgddVv
1pvuGcJDZwYiwfiXr3FL
=HHrh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
The existing gpio_to_irq() implementation on sa1100 only translates
validly for internal GPIOs. Since this sub-arch enables GPIOLIB
support, this results in buggy translations for non-internal GPIOs.
Get rid of the private gpio_to_irq() implementation, replacing it
with the .to_irq method in the sa1100 gpio chip instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
Core:
* Support for the HS200 high-speed eMMC mode.
* Support SDIO 3.0 Ultra High Speed cards.
* Kill pending block requests immediately if card is removed.
* Enable the eMMC feature for locking boot partitions read-only
until next power on, exposed via sysfs.
Drivers:
* Runtime PM support for Intel Medfield SDIO.
* Suspend/resume support for sdhci-spear.
* sh-mmcif now processes requests asynchronously.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LJnN
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
MMC highlights for 3.3:
Core:
* Support for the HS200 high-speed eMMC mode.
* Support SDIO 3.0 Ultra High Speed cards.
* Kill pending block requests immediately if card is removed.
* Enable the eMMC feature for locking boot partitions read-only
until next power on, exposed via sysfs.
Drivers:
* Runtime PM support for Intel Medfield SDIO.
* Suspend/resume support for sdhci-spear.
* sh-mmcif now processes requests asynchronously.
* tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (58 commits)
mmc: fix a deadlock between system suspend and MMC block IO
mmc: sdhci: restore the enabled dma when do reset all
mmc: dw_mmc: miscaculated the fifo-depth with wrong bit operation
mmc: host: Adds support for eMMC 4.5 HS200 mode
mmc: core: HS200 mode support for eMMC 4.5
mmc: dw_mmc: fixed wrong bit operation for SDMMC_GET_FCNT()
mmc: core: Separate the timeout value for cache-ctrl
mmc: sdhci-spear: Fix compilation error
mmc: sdhci: Deal with failure case in sdhci_suspend_host
mmc: dw_mmc: Clear the DDR mode for non-DDR
mmc: sd: Fix SDR12 timing regression
mmc: sdhci: Fix tuning timer incorrect setting when suspending host
mmc: core: Add option to prevent eMMC sleep command
mmc: omap_hsmmc: use threaded irq handler for card-detect.
mmc: sdhci-pci: enable runtime PM for Medfield SDIO
mmc: sdhci: Always pass clock request value zero to set_clock host op
mmc: sdhci-pci: remove SDHCI_QUIRK2_OWN_CARD_DETECTION
mmc: sdhci-pci: get gpio numbers from platform data
mmc: sdhci-pci: add platform data
mmc: sdhci: prevent card detection activity for non-removable cards
...
Commit 8a25a2fd12 ("cpu: convert 'cpu' and 'machinecheck' sysdev_class
to a regular subsystem") changed how things are dealt with in the MCE
subsystem. Some of the things that got broken due to this are CPU
hotplug and suspend/hibernate.
MCE uses per_cpu allocations of struct device. So, when a CPU goes
offline and comes back online, in order to ensure that we start from a
clean slate with respect to the MCE subsystem, zero out the entire
per_cpu device structure to 0 before using it.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the reverted condition in sh7372_a3sp_suspend().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Several platforms are now using the memblock_alloc+memblock_free+
memblock_remove trick to obtain memory which won't be mapped in the
kernel's page tables. Most platforms do this (correctly) in the
->reserve callback. However, OMAP has started to call these functions
outside of this callback, and this is extremely unsafe - memory will
not be unmapped, and could well be given out after memblock is no
longer responsible for its management.
So, provide arm_memblock_steal() to perform this function, and ensure
that it panic()s if it is used inappropriately. Convert everyone
over, including OMAP.
As a result, OMAP with OMAP4_ERRATA_I688 enabled will panic on boot
with this change. Mark this option as BROKEN and make it depend on
BROKEN. OMAP needs to be fixed, or 137d105d50 (ARM: OMAP4: Fix
errata i688 with MPU interconnect barriers.) reverted until such
time it can be fixed correctly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a check for the presence of the LPAE feature during the
CPU initialisation. If not present, it reports an error when
CONFIG_DEBUG_LL is enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change ensures the platform device name matches nuc900-ac97 platform
driver name.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew explains:
- various misc stuff
- Most of the rest of MM: memcg, threaded hugepages, others.
- cpumask
- kexec
- kdump
- some direct-io performance tweaking
- radix-tree optimisations
- new selftests code
A note on this: often people will develop a new userspace-visible
feature and will develop userspace code to exercise/test that
feature. Then they merge the patch and the selftest code dies.
Sometimes we paste it into the changelog. Sometimes the code gets
thrown into Documentation/(!).
This saddens me. So this patch creates a bare-bones framework which
will henceforth allow me to ask people to include their test apps in
the kernel tree so we can keep them alive. Then when people enhance
or fix the feature, I can ask them to update the test app too.
The infrastruture is terribly trivial at present - let's see how it
evolves.
- checkpoint/restart feature work.
A note on this: this is a project by various mad Russians to perform
c/r mainly from userspace, with various oddball helper code added
into the kernel where the need is demonstrated.
So rather than some large central lump of code, what we have is
little bits and pieces popping up in various places which either
expose something new or which permit something which is normally
kernel-private to be modified.
The overall project is an ongoing thing. I've judged that the size
and scope of the thing means that we're more likely to be successful
with it if we integrate the support into mainline piecemeal rather
than allowing it all to develop out-of-tree.
However I'm less confident than the developers that it will all
eventually work! So what I'm asking them to do is to wrap each piece
of new code inside CONFIG_CHECKPOINT_RESTORE. So if it all
eventually comes to tears and the project as a whole fails, it should
be a simple matter to go through and delete all trace of it.
This lot pretty much wraps up the -rc1 merge for me.
* akpm: (96 commits)
unlzo: fix input buffer free
ramoops: update parameters only after successful init
ramoops: fix use of rounddown_pow_of_two()
c/r: prctl: add PR_SET_MM codes to set up mm_struct entries
c/r: procfs: add start_data, end_data, start_brk members to /proc/$pid/stat v4
c/r: introduce CHECKPOINT_RESTORE symbol
selftests: new x86 breakpoints selftest
selftests: new very basic kernel selftests directory
radix_tree: take radix_tree_path off stack
radix_tree: remove radix_tree_indirect_to_ptr()
dio: optimize cache misses in the submission path
vfs: cache request_queue in struct block_device
fs/direct-io.c: calculate fs_count correctly in get_more_blocks()
drivers/parport/parport_pc.c: fix warnings
panic: don't print redundant backtraces on oops
sysctl: add the kernel.ns_last_pid control
kdump: add udev events for memory online/offline
include/linux/crash_dump.h needs elf.h
kdump: fix crash_kexec()/smp_send_stop() race in panic()
kdump: crashk_res init check for /sys/kernel/kexec_crash_size
...
KMSG_DUMP_KEXEC is useless because we already save kernel messages inside
/proc/vmcore, and it is unsafe to allow modules to do other stuffs in a
crash dump scenario.
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
node_to_cpumask() has been replaced by cpumask_of_node(), and wholly
removed since commit 29c337a0 ("cpumask: remove obsolete node_to_cpumask
now everyone uses cpumask_of_node").
So update the comments for setup_node_to_cpumask_map().
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so those calls to
set_fs(USER_DS) are redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move CMPXCHG_DOUBLE and rename it to HAVE_CMPXCHG_DOUBLE so architectures
can simply select the option if it is supported.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move CMPXCHG_LOCAL and rename it to HAVE_CMPXCHG_LOCAL so architectures
can simply select the option if it is supported.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While implementing cmpxchg_double() on s390 I realized that we don't set
CONFIG_CMPXCHG_LOCAL despite the fact that we have support for it.
However setting that option will increase the size of struct page by
eight bytes on 64 bit, which we certainly do not want. Also, it doesn't
make sense that a present cpu feature should increase the size of struct
page.
Besides that it looks like the dependency to CMPXCHG_LOCAL is wrong and
that it should depend on CMPXCHG_DOUBLE instead.
This patch:
If an architecture supports CMPXCHG_LOCAL this shouldn't result
automatically in larger struct pages if the SLUB allocator is used.
Instead introduce a new config option "HAVE_ALIGNED_STRUCT_PAGE" which
can be selected if a double word aligned struct page is required. Also
update x86 Kconfig so that it should work as before.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=dgrs
-----END PGP SIGNATURE-----
Merge tag 'to-linus' of git://github.com/rustyrussell/linux
* tag 'to-linus' of git://github.com/rustyrussell/linux: (24 commits)
lguest: Make sure interrupt is allocated ok by lguest_setup_irq
lguest: move the lguest tool to the tools directory
lguest: switch segment-voodoo-numbers to readable symbols
virtio: balloon: Add freeze, restore handlers to support S4
virtio: balloon: Move vq initialization into separate function
virtio: net: Add freeze, restore handlers to support S4
virtio: net: Move vq and vq buf removal into separate function
virtio: net: Move vq initialization into separate function
virtio: blk: Add freeze, restore handlers to support S4
virtio: blk: Move vq initialization to separate function
virtio: console: Disable callbacks for virtqueues at start of S4 freeze
virtio: console: Add freeze and restore handlers to support S4
virtio: console: Move vq and vq buf removal into separate functions
virtio: pci: add PM notification handlers for restore, freeze, thaw, poweroff
virtio: pci: switch to new PM API
virtio_blk: fix config handler race
virtio: add debugging if driver doesn't kick.
virtio: expose added descriptors immediately.
virtio: avoid modulus operation.
virtio: support unlocked queue kick
...
This very noisy sparse warning appears on almost every file in the
kernel:
CHECK init/main.c
arch/x86/include/asm/thread_info.h:43:55: error: dubious one-bit signed bitfield
arch/x86/include/asm/thread_info.h:44:46: error: dubious one-bit signed bitfield
This patch changes sig_on_uaccess_error and uaccess_err flags to unsigned
type and thus fixes the warning.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
ALSA: usb-audio: add Yamaha MOX6/MOX8 support
ALSA: virtuoso: add S/PDIF input support for all Xonars
ALSA: ice1724 - Support for ooAoo SQ210a
ALSA: ice1724 - Allow card info based on model only
ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
ALSA: hdspm - Provide unique driver id based on card serial
ASoC: Dynamically allocate the rtd device for a non-empty release()
ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
ALSA: hda/cirrus - support for iMac12,2 model
ASoC: cx20442: add bias control over a platform provided regulator
ALSA: usb-audio - Avoid flood of frame-active debug messages
ALSA: snd-usb-us122l: Delete calls to preempt_disable
mfd: Put WM8994 into cache only mode when suspending
...
Fix up trivial conflicts in:
- arch/arm/mach-s3c64xx/mach-crag6410.c:
renamed speyside_wm8962 to tobermory, added littlemill right
next to it
- drivers/base/regmap/{regcache.c,regmap.c}:
duplicate diff that had already come in with other changes in
the regmap tree
We only need amd_bus.o for AMD systems with PCI. arch/x86/pci/Makefile
already depends on CONFIG_PCI=y, so this patch just adds the dependency
on CONFIG_AMD_NB.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org # 2.6.34+ (needs adjustment for k8 -> amd rename)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk8Obj8ACgkQGkmNcg7/o7hzngCfS5az4ZP3D+e/cvatHZm/nAzn
0mIAoKbYyXpLXGkEN+yDkd5YZAYwQjVR
=kryV
-----END PGP SIGNATURE-----
Merge tag 'rmobile-for-linus' of git://github.com/pmundt/linux-sh
SH/R-Mobile updates for 3.3 merge window.
* tag 'rmobile-for-linus' of git://github.com/pmundt/linux-sh: (32 commits)
arm: mach-shmobile: add a resource name for shdma
ARM: mach-shmobile: r8a7779 SMP support V3
ARM: mach-shmobile: Add kota2 defconfig.
ARM: mach-shmobile: Add marzen defconfig.
ARM: mach-shmobile: r8a7779 power domain support V2
ARM: mach-shmobile: Fix up marzen build for recent GIC changes.
ARM: mach-shmobile: r8a7779 PFC function support
ARM: mach-shmobile: Flush caches in platform_cpu_die()
ARM: mach-shmobile: Allow SoC specific CPU kill code
ARM: mach-shmobile: Fix headsmp.S code to use CPUINIT
ARM: mach-shmobile: clock-r8a7779: clkz/clkzs support
ARM: mach-shmobile: clock-r8a7779: add DIV4 clock support
ARM: mach-shmobile: Marzen LAN89218 support
ARM: mach-shmobile: Marzen SCIF2/SCIF4 support
ARM: mach-shmobile: r8a7779 PFC GPIO-only support V2
ARM: mach-shmobile: r8a7779 and Marzen base support V2
sh: pfc: Unlock register support
sh: pfc: Variable bitfield width config register support
sh: pfc: Add config_reg_helper() function
sh: pfc: Convert index to field and value pair
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk8ObfwACgkQGkmNcg7/o7gOHwCfZo8197ppks1LIfACo27cL8Q8
rU8AnR+igHfCEkg9RlrX9sJ8jqxtpYLZ
=WE1M
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
SuperH updates for 3.3 merge window.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (38 commits)
sh: magicpanelr2: Update for parse_mtd_partitions() fallout.
sh: mach-rsk: Update for parse_mtd_partitions() fallout.
sh: sh2a: Improve cache flush/invalidate functions
sh: also without PM_RUNTIME pm_runtime.o must be built
sh: add a resource name for shdma
sh: Remove redundant try_to_freeze() invocations.
sh: Ensure IRQs are enabled across do_notify_resume().
sh: Fix up store queue code for subsys_interface changes.
sh: clkfwk: sh_clk_init_parent() should be called after clk_register()
sh: add platform_device for renesas_usbhs in board-sh7757lcr
sh: modify clock-sh7757 for renesas_usbhs
sh: pfc: ioremap() support
sh: use ioread32/iowrite32 and mapped_reg for div6
sh: use ioread32/iowrite32 and mapped_reg for div4
sh: use ioread32/iowrite32 and mapped_reg for mstp32
sh: extend clock struct with mapped_reg member
sh: clkfwk: clock-sh73a0: all div6_clks use SH_CLK_DIV6_EXT()
sh: clkfwk: clock-sh7724: all div6_clks use SH_CLK_DIV6_EXT()
sh: clock-sh7723: add CLKDEV_ICK_ID for cleanup
serial: sh-sci: Handle GPIO function requests.
...
Make sure the interrupt is allocated correctly by lguest_setup_irq (check the
return value of irq_alloc_desc_at for -ENOMEM)
Signed-off-by: Stratos Psomadakis <psomas@cslab.ece.ntua.gr>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (cleanups and commentry)
Add pm_caps into platform_data. This is power management, usually
for SDIO device such as SDIO WLAN.
Signed-off-by: Sangwook Lee <sangwook.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The RSK+ setup code was doing some pretty dubious things with
parse_mtd_partitions() in order to populate the physmap-flash map
platform data. The physmap-flash driver contains all of the functionality
that we require already, so simply drop the special casing and pad out
the platform data accordingly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The cache functions lock out interrupts for long periods; this patch
reduces the impact when operating on large address ranges. In such
cases it will:
- Invalidate the entire cache rather than individual addresses.
- Do nothing when flushing the operand cache in write-through mode.
- When flushing the operand cache in write-back mdoe, index the
search for matching addresses on the cache entires instead of the
addresses to flush
Note: sh2a__flush_purge_region was only invalidating the operand
cache, this adds flush.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel config: Fix the APB_TIMER selection
x86/mrst: Add additional debug prints for pb_keys
x86/intel config: Revamp configuration to allow for Moorestown and Medfield
x86/intel/scu/ipc: Match the changes in the x86 configuration
x86/apb: Fix configuration constraints
x86: Fix INTEL_MID silly
x86/Kconfig: Cyclone-timer depends on x86-summit
x86: Reduce clock calibration time during slave cpu startup
x86/config: Revamp configuration for MID devices
x86/sfi: Kill the IRQ as id hack
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, reboot: Fix typo in nmi reboot path
x86, NMI: Add to_cpumask() to silence compile warning
x86, NMI: NMI selftest depends on the local apic
x86: Add stack top margin for stack overflow checking
x86, NMI: NMI-selftest should handle the UP case properly
x86: Fix the 32-bit stackoverflow-debug build
x86, NMI: Add knob to disable using NMI IPIs to stop cpus
x86, NMI: Add NMI IPI selftest
x86, reboot: Use NMI instead of REBOOT_VECTOR to stop cpus
x86: Clean up the range of stack overflow checking
x86: Panic on detection of stack overflow
x86: Check stack overflow in detail
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/numa: Add constraints check for nid parameters
mm, x86: Remove debug_pagealloc_enabled
x86/mm: Initialize high mem before free_all_bootmem()
arch/x86/kernel/e820.c: quiet sparse noise about plain integer as NULL pointer
arch/x86/kernel/e820.c: Eliminate bubble sort from sanitize_e820_map()
x86: Fix mmap random address range
x86, mm: Unify zone_sizes_init()
x86, mm: Prepare zone_sizes_init() for unification
x86, mm: Use max_low_pfn for ZONE_NORMAL on 64-bit
x86, mm: Wrap ZONE_DMA32 with CONFIG_ZONE_DMA32
x86, mm: Use max_pfn instead of highend_pfn
x86, mm: Move zone init from paging_init() on 64-bit
x86, mm: Use MAX_DMA_PFN for ZONE_DMA on 32-bit
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: (23 commits)
[CPUFREQ] EXYNOS: Removed useless headers and codes
[CPUFREQ] EXYNOS: Make EXYNOS common cpufreq driver
[CPUFREQ] powernow-k8: Update copyright, maintainer and documentation information
[CPUFREQ] powernow-k8: Fix indexing issue
[CPUFREQ] powernow-k8: Avoid Pstate MSR accesses on systems supporting CPB
[CPUFREQ] update lpj only if frequency has changed
[CPUFREQ] cpufreq:userspace: fix cpu_cur_freq updation
[CPUFREQ] Remove wall variable from cpufreq_gov_dbs_init()
[CPUFREQ] EXYNOS4210: cpufreq code is changed for stable working
[CPUFREQ] EXYNOS4210: Update frequency table for cpu divider
[CPUFREQ] EXYNOS4210: Remove code about bus on cpufreq
[CPUFREQ] s3c64xx: Use pr_fmt() for consistent log messages
cpufreq: OMAP: fixup for omap_device changes, include <linux/module.h>
cpufreq: OMAP: fix freq_table leak
cpufreq: OMAP: put clk if cpu_init failed
cpufreq: OMAP: only supports OPP library
cpufreq: OMAP: dont support !freq_table
cpufreq: OMAP: deny initialization if no mpudev
cpufreq: OMAP: move clk name decision to init
cpufreq: OMAP: notify even with bad boot frequency
...
* git://git.infradead.org/battery-2.6: (68 commits)
power_supply: Mark da9052 driver as broken
power_supply: Drop usage of nowarn variant of sysfs_create_link()
s3c_adc_battery: Average over more than one adc sample
power_supply: Add DA9052 battery driver
isp1704_charger: Fix missing check
jz4740-battery: Fix signedness bug
power_supply: Assume mains power by default
sbs-battery: Fix devicetree match table
ARM: rx51: Add bq27200 i2c board info
sbs-battery: Change power supply name
devicetree-bindings: Propagate bq20z75->sbs rename to dt bindings
devicetree-bindings: Add vendor entry for Smart Battery Systems
sbs-battery: Rename internals to new name
bq20z75: Rename to sbs-battery
wm97xx_battery: Use DEFINE_MUTEX() for work_lock
max8997_charger: Remove duplicate module.h
lp8727_charger: Some minor fixes for the header
lp8727_charger: Add header file
power_supply: Convert drivers/power/* to use module_platform_driver()
power_supply: Add "unknown" in power supply type
...
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
This patch contains r8a7779 SMP support V3 - now including
CPU hotplug offine and online support. The r8a7779 power
domain code is tied together with SMP glue code which allows
us to control the power domains via CPU hotplug.
At this point the kernel boots with the 4 Cortex-A9 cores in
SMP mode and all CPU cores except CPU0 can be hotplugged.
The code in platsmp.c is quite far from pretty, but it is
kept like that intentionally to avoid creating layers of
code that will go away in the near future anyway. The code
needs to be updated when some per-SoC handling code will be
added to the ARM architecture, see the following patch for
more information:
"[RFC PATCH 0/3] Per SoC descriptor"
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
frv, h8300, m68k, microblaze, openrisc, score, um and xtensa currently
do not register a CPU device. Add the config option GENERIC_CPU_DEVICES
which causes a generic CPU device to be registered for each present CPU,
and make all these architectures select it.
Richard Weinberger <richard@nod.at> covered UML and suggested using
per_cpu.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 5d910426a6.
Nicolas Ferre <nicolas.ferre@atmel.com> wrote:
"Unfortunately this is not true for all the SoC that embed the
atmel_lcdfb... So I may need to rework this patch but it is certainly
not applicable in the current form."
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Framebuffer driver needs to fetch the video data during the rising
edge of the VCLK. Otherwise, there are some glitches in the LCD
display.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
0 is a valid IRQ but the interrupt line for the pca935x certainly isn't
connected there which causes it to fail to probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rather than letting them get allocated dynamically where we don't know
where they are, and also name the data line resource as gpio-generic
requires that. Without these changes the GPIOs are useless.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The second MMC slot was only present on revision 1 of Cragganmore so
remove it. Only MMC0 and MMC2 are there on production systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that we have software runtime power management support this code is
redundant.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The function declarations in plat/s3c64xx-spi.h rely on struct
platform_device but it's not declared by the header causing compiler
warnings if it is included prior to another header which does that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
dma-ops.h uses samsung_dma_is_dmadev so it needs to have mach/dma.h
included.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Otherwise it'll generate errors if included twice.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Only available for R4000 style TLBs anyway and proper ordering of
initialization code made this crude interface unncecessary.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On MIPS the generic PCI code has always defaulted to L1_CACHE_BYTES
because the architecutre PCI code did not provide a better default.
In particular on systems with S-caches or T-caches this was suboptimal.
Provide a better default by setting pci_dfl_cache_line_size based on
the size of the line size of the lowest level of the cache hierarchy.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2982/
When flushing TLB, if @vma is backed by huge page, we could flush huge
TLB, due to that huge page is defined to be far from normal page.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: "Jayachandran C." <jayachandranc@netlogicmicro.com>
Patchwork: https://patchwork.linux-mips.org/patch/2825/
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Hillf Danton <dhillf@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3114/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Init topology subsystem by cpu registration.
Microblaze Linux kernel is fauling by
"Oops: kernel access of bad area, sig: 11"
because cpu is not initialized.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPBZXBAAoJECgfDbjSjVRpuuYIAIMD0wE96MuTOSBJX4VG8VAP
UyjL9dsfMRy8CKioQo5/fxpTY07YBCWmNauSSX7pzgcoUKBfYIGn4Z1qwGYsWK9M
CzLs6PXLTugw0FtKobHZl/klRTWEBS6YOUjp9x568rplwF+Ppk7b993uj7eS/g+e
T0mUKzqg4/UavbHd9+W5KgC4drQ5hgtu2WZHoUxBK4umnd3C2G+U82Sthg50o/XU
SC8IGm39K8I36HoIWgXj3Y7nkOP3mQELohOT4ZPiVSmLvGS4i47+ix75anO+8ZvZ
jxHr8RC85IK1Nd89NZhbKOyvx0QQiwoKUZaTwcWXJNSOADzZnM6icdIsodc+Elo=
=ccQZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
lib: use generic pci_iomap on all architectures
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
alpha: drop pci_iomap/pci_iounmap from pci-noop.c
mn10300: switch to GENERIC_PCI_IOMAP
mn10300: add missing __iomap markers
frv: switch to GENERIC_PCI_IOMAP
tile: switch to GENERIC_PCI_IOMAP
tile: don't panic on iomap
sparc: switch to GENERIC_PCI_IOMAP
sh: switch to GENERIC_PCI_IOMAP
powerpc: switch to GENERIC_PCI_IOMAP
parisc: switch to GENERIC_PCI_IOMAP
mips: switch to GENERIC_PCI_IOMAP
microblaze: switch to GENERIC_PCI_IOMAP
arm: switch to GENERIC_PCI_IOMAP
alpha: switch to GENERIC_PCI_IOMAP
lib: add GENERIC_PCI_IOMAP
lib: move GENERIC_IOMAP to lib/Kconfig
Fix up trivial conflicts due to changes nearby in arch/{m68k,score}/Kconfig
Unpaired calling of __trace_hcall_entry and __trace_hcall_exit could
cause incorrect preempt count. And it might happen as the global
variable hcall_tracepoint_refcount is checked separately before calling
them.
Instead, store the value that was used on entry in the stack frame
and retreive it from there after the call
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Wire-up new system calls
microblaze: Remove NO_IRQ from architecture
input: xilinx_ps2: Don't use NO_IRQ
block: xsysace: Don't use NO_IRQ
microblaze: Trivial asm fix
microblaze: Fix debug message in module
microblaze: Remove eprintk macro
microblaze: Send CR before LF for early console
microblaze: Change NO_IRQ to 0
microblaze: Use irq_of_parse_and_map for timer
microblaze: intc: Change variable name
microblaze: Use of_find_compatible_node for timer and intc
microblaze: Add __cmpdi2
microblaze: Synchronize __pa __va macros
Tracepoints should not be called inside an rcu_idle_enter/rcu_idle_exit
region. Since pSeries calls H_CEDE in the idle loop, we were violating
this rule.
commit a7b152d534 (powerpc: Tell RCU about idle after hcall tracing)
tried to work around it by delaying the rcu_idle_enter until after we
called the hcall tracepoint, but there are a number of issues with it.
The hcall tracepoint trampoline code is called conditionally when the
tracepoint is enabled. If the tracepoint is not enabled we never call
rcu_idle_enter. The idle_uses_rcu check was also done at compile time
which breaks multiplatform builds.
The simple fix is to avoid tracing H_CEDE and rely on other tracepoints
and the hypervisor dispatch trace log to work out if we called H_CEDE.
This fixes a hang during boot on pSeries.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Andrew elucidates:
- First installmeant of MM. We have a HUGE number of MM patches this
time. It's crazy.
- MAINTAINERS updates
- backlight updates
- leds
- checkpatch updates
- misc ELF stuff
- rtc updates
- reiserfs
- procfs
- some misc other bits
* akpm: (124 commits)
user namespace: make signal.c respect user namespaces
workqueue: make alloc_workqueue() take printf fmt and args for name
procfs: add hidepid= and gid= mount options
procfs: parse mount options
procfs: introduce the /proc/<pid>/map_files/ directory
procfs: make proc_get_link to use dentry instead of inode
signal: add block_sigmask() for adding sigmask to current->blocked
sparc: make SA_NOMASK a synonym of SA_NODEFER
reiserfs: don't lock root inode searching
reiserfs: don't lock journal_init()
reiserfs: delay reiserfs lock until journal initialization
reiserfs: delete comments referring to the BKL
drivers/rtc/interface.c: fix alarm rollover when day or month is out-of-range
drivers/rtc/rtc-twl.c: add DT support for RTC inside twl4030/twl6030
drivers/rtc/: remove redundant spi driver bus initialization
drivers/rtc/rtc-jz4740.c: make jz4740_rtc_driver static
drivers/rtc/rtc-mc13xxx.c: make mc13xxx_rtc_idtable static
rtc: convert drivers/rtc/* to use module_platform_driver()
drivers/rtc/rtc-wm831x.c: convert to devm_kzalloc()
drivers/rtc/rtc-wm831x.c: remove unused period IRQ handler
...
Abstract the code sequence for adding a signal handler's sa_mask to
current->blocked because the sequence is identical for all architectures.
Furthermore, in the past some architectures actually got this code wrong,
so introduce a wrapper that all architectures can use.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unlike other architectures, sparc currently has no SA_NODEFER definition
but only the older SA_NOMASK. Since SA_NOMASK is the historical name for
SA_NODEFER, add SA_NODEFER and copy what other architectures do by making
SA_NOMASK a synonym for SA_NODEFER.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... by selecting ARCH_BINFMT_ELF_RANDOMIZE_PIE
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randomization of PIE load address is hard coded in binfmt_elf.c for X86
and ARM. Create a new Kconfig variable
(CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE) for this and use it instead. Thus
architecture specific policy is pushed out of the generic binfmt_elf.c and
into the architecture Kconfig files.
X86 and ARM Kconfigs are modified to select the new variable so there is
no change in behavior. A follow on patch will select it for MIPS too.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SUN4M per-cpu timers have two modes of work. These are timer mode and
counter mode. Kernel doesn't write anything to the register, which is
connected with mode choice.
So, the mode is chosen by bootloader. This patch forces to use timer
mode from the kernel and to be independent of bootloader.
I had this problem with OpenBIOS. Timers don't tick and kernel fails on
QEMU, when it's compiled with SMP support. The patch fixes problem.
Signed-off-by: Tkhai Kirill <tkhai@yandex.ru>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk8Mq/MACgkQdwG7hYl686PeFACfZCgbdDWD9A/JL+i1RMfExVu6
Pi0An3Hmc3PTCp0yQ21KtcKhpF9CAMEu
=NfuL
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6
MTD pull for 3.3
* tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6: (113 commits)
mtd: Fix dependency for MTD_DOC200x
mtd: do not use mtd->block_markbad directly
logfs: do not use 'mtd->block_isbad' directly
mtd: introduce mtd_can_have_bb helper
mtd: do not use mtd->suspend and mtd->resume directly
mtd: do not use mtd->lock, unlock and is_locked directly
mtd: do not use mtd->sync directly
mtd: harmonize mtd_writev usage
mtd: do not use mtd->lock_user_prot_reg directly
mtd: mtd->write_user_prot_reg directly
mtd: do not use mtd->read_*_prot_reg directly
mtd: do not use mtd->get_*_prot_info directly
mtd: do not use mtd->read_oob directly
mtd: mtdoops: do not use mtd->panic_write directly
romfs: do not use mtd->get_unmapped_area directly
mtd: do not use mtd->get_unmapped_area directly
mtd: do use mtd->point directly
mtd: introduce mtd_has_oob helper
mtd: mtdcore: export symbols cleanup
mtd: clean-up the default_mtd_writev function
...
Fix up trivial edit/remove conflict in drivers/staging/spectra/lld_mtd.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tc3589x-keypad - add missing kerneldoc
Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
Input: ucb1400_ts - convert to threaded IRQ
Input: ucb1400_ts - drop inline annotations
Input: usb1400_ts - add __devinit/__devexit section annotations
Input: ucb1400_ts - set driver owner
Input: ucb1400_ts - convert to use dev_pm_ops
Input: psmouse - make sure we do not use stale methods
Input: evdev - do not block waiting for an event if fd is nonblock
Input: evdev - if no events and non-block, return EAGAIN not 0
Input: evdev - only allow reading events if a full packet is present
Input: add driver for pixcir i2c touchscreens
Input: samsung-keypad - implement runtime power management support
Input: tegra-kbc - report wakeup key for some platforms
Input: tegra-kbc - add device tree bindings
Input: add driver for AUO In-Cell touchscreens using pixcir ICs
Input: mpu3050 - configure the sampling method
Input: mpu3050 - ensure we enable interrupts
Input: mpu3050 - add of_match table for device-tree probing
Input: sentelic - document the latest hardware
...
Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (31 commits)
pinctrl: remove unnecessary max pin number
pinctrl: correct a offset while enumerating pins
pinctrl: some typo fixes
pinctrl: rename U300 and SIRF pin controllers
pinctrl: pass name instead of device to pin_config_*
pinctrl: add "struct seq_file;" to pinconf.h
pinctrl: conjure names for unnamed pins
pinctrl: add a group-specific hog macro
pinctrl: don't create a device for each pin controller
arm/u300: don't use PINMUX_MAP_PRIMARY*
pinctrl: implement PINMUX_MAP_SYS_HOG
pinctrl: add a pin config interface
pinctrl/coh901: driver to request its pins
pinctrl: u300-pinmux: register proper GPIO ranges
pinctrl: move the U300 GPIO driver to pinctrl
ARM: u300: localize GPIO assignments
pinctrl: make it possible to add multiple maps
pinctrl: make a copy of pinmux map
pinctrl: GPIO direction support for muxing
pinctrl: print pin range in GPIO range debugs
...
* 'stable/for-linus-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (37 commits)
xen/pciback: Expand the warning message to include domain id.
xen/pciback: Fix "device has been assigned to X domain!" warning
xen/pciback: Move the PCI_DEV_FLAGS_ASSIGNED ops to the "[un|]bind"
xen/xenbus: don't reimplement kvasprintf via a fixed size buffer
xenbus: maximum buffer size is XENSTORE_PAYLOAD_MAX
xen/xenbus: Reject replies with payload > XENSTORE_PAYLOAD_MAX.
Xen: consolidate and simplify struct xenbus_driver instantiation
xen-gntalloc: introduce missing kfree
xen/xenbus: Fix compile error - missing header for xen_initial_domain()
xen/netback: Enable netback on HVM guests
xen/grant-table: Support mappings required by blkback
xenbus: Use grant-table wrapper functions
xenbus: Support HVM backends
xen/xenbus-frontend: Fix compile error with randconfig
xen/xenbus-frontend: Make error message more clear
xen/privcmd: Remove unused support for arch specific privcmp mmap
xen: Add xenbus_backend device
xen: Add xenbus device driver
xen: Add privcmd device driver
xen/gntalloc: fix reference counts on multi-page mappings
...
* 'kvm-updates/3.3' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (74 commits)
KVM: PPC: Whitespace fix for kvm.h
KVM: Fix whitespace in kvm_para.h
KVM: PPC: annotate kvm_rma_init as __init
KVM: x86 emulator: implement RDPMC (0F 33)
KVM: x86 emulator: fix RDPMC privilege check
KVM: Expose the architectural performance monitoring CPUID leaf
KVM: VMX: Intercept RDPMC
KVM: SVM: Intercept RDPMC
KVM: Add generic RDPMC support
KVM: Expose a version 2 architectural PMU to a guests
KVM: Expose kvm_lapic_local_deliver()
KVM: x86 emulator: Use opcode::execute for Group 9 instruction
KVM: x86 emulator: Use opcode::execute for Group 4/5 instructions
KVM: x86 emulator: Use opcode::execute for Group 1A instruction
KVM: ensure that debugfs entries have been created
KVM: drop bsp_vcpu pointer from kvm struct
KVM: x86: Consolidate PIT legacy test
KVM: x86: Do not rely on implicit inclusions
KVM: Make KVM_INTEL depend on CPU_SUP_INTEL
KVM: Use memdup_user instead of kmalloc/copy_from_user
...
Add power domain control support for the r8a7779 SoC V2.
This adds support for 4 power domains for I/O Devices
together with code that can be used for CPU cores as well.
The only out of the ordinary experience is the need for
ioremap() of SYSC registers. Because of that we need to
execute some init function before setting up the domains.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
do_notify_resume() can trigger the freezer via the try_to_freeze() path
(both explicitly through a redundant call in do_signal() or via
get_signal_to_deliver()). That IRQs were disabled across this callsite
became apparent with the might_sleep() introduction in try_to_freeze() by
Tejun in a0acae0e88, resulting in:
BUG: sleeping function called from invalid context at include/linux/freezer.h:45
in_atomic(): 0, irqs_disabled(): 1, pid: 819, name: ntpd
no locks held by ntpd/819.
Stack: (0x9c81be80 to 0x9c81c000)
...
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add r8a7779 PFC function support using the shared PFC code.
Depends on variable bitfield config register patches.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
atomic64_read() doesn't actually write anything (as far as the C
environment is concerned... the CPU does actually write but that's an
implementation quirk), so it should take a const pointer.
This does NOT mean that it is safe to use atomic64_read() on an object
in readonly storage (it will trap!)
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/20120109165859.1879abda.akpm@linux-foundation.org
Linus Torvalds