This was tested on a NETGEAR ReadyNAS 2120 device (Marvell Armada XP
based board, via DT).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon fixes and updates from Jean Delvare:
"All lm90 driver fixes and improvements"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation: dt: hwmon: Add OF document for LM90
hwmon: (lm90) Add power control
hwmon: (lm90) Add support for TI TMP451
hwmon: (lm90) Use enums for the indexes of temp8 and temp11
hwmon: (lm90) Add support to handle IRQ
hwmon: (lm90) Define status bits
hwmon: (lm90) Fix max6696 alarm handling
The device lm90 can be controlled by the vcc rail.
Adding the regulator support to power on/off the vcc rail.
Enable the "vcc" regulator before accessing the device.
[JD: Rename variables to avoid confusion with registers.]
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
TI TMP451 is mostly compatible with ADT7461, except for
local temperature low byte and max conversion rate.
Add support to the LM90 driver.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Using enums for the indexes and nrs of temp8 and temp11.
This make the code much more readable.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When the temperature exceed the limit range value,
the driver can handle the interrupt.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add bit defines for the status register. And add a function
lm90_is_tripped() which will read status register and return
tripped or not, then lm90_alert can call it directly, and in the
future the IRQ thread also can use it.
[JD: Adjusted to include all the new MAX6696 status flags.]
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Bit 2 of status register 2 on MAX6696 (external diode 2 open)
sets ALERT; the bit thus has to be listed in alert_alarms.
Also display a message in the alert handler if the condition
is encountered.
Even though not all overtemperature conditions cause ALERT
to be set, we should not ignore them in the alert handler.
Display messages for all out-of-range conditions.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As well as the usual driver updates and cleanups there's a few
improvements to the core here:
- The start of some improvements to factor out more of the SPI message
loop into the core. Right now this is just simplifying the code a
bit but hopefully next time around we'll also have managed to roll
out some noticable performance improvements which drivers can take
advantage of.
- Support for loading modules for ACPI enumerated SPI devices.
- Managed registration for SPI controllers.
- Helper for another common I/O pattern.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=emSz
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"As well as the usual driver updates and cleanups there's a few
improvements to the core here:
- The start of some improvements to factor out more of the SPI
message loop into the core. Right now this is just simplifying the
code a bit but hopefully next time around we'll also have managed
to roll out some noticable performance improvements which drivers
can take advantage of.
- Support for loading modules for ACPI enumerated SPI devices.
- Managed registration for SPI controllers.
- Helper for another common I/O pattern"
* tag 'spi-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (116 commits)
spi/hspi: add device tree support
spi: atmel: fix return value check in atmel_spi_probe()
spi: spi-imx: only enable the clocks when we start to transfer a message
spi/s3c64xx: Fix doubled clock disable on suspend
spi/s3c64xx: Do not ignore return value of spi_master_resume/suspend
spi: spi-mxs: Use u32 instead of uint32_t
spi: spi-mxs: Don't set clock for each xfer
spi: spi-mxs: Clean up setup_transfer function
spi: spi-mxs: Remove check of spi mode bits
spi: spi-mxs: Fix race in setup method
spi: spi-mxs: Remove bogus setting of ssp clk rate field
spi: spi-mxs: Remove full duplex check, spi core already does it
spi: spi-mxs: Fix chip select control bits in DMA mode
spi: spi-mxs: Fix extra CS pulses and read mode in multi-transfer messages
spi: spi-mxs: Change flag arguments in txrx functions to bit flags
spi: spi-mxs: Always clear INGORE_CRC, to keep CS asserted
spi: spi-mxs: Remove mxs_spi_enable and mxs_spi_disable
spi: spi-mxs: Always set LOCK_CS
spi/s3c64xx: Add missing pm_runtime_put on setup fail
spi/s3c64xx: Add missing pm_runtime_set_active() call in probe()
...
We cap the upper bound of "mtimeout" but since it's signed we should
check for negative values as well. The mistake is harmless. But I have
changed it to unsigned as a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
EMC1404 and EMC1424 are similar to EMC1403 and EMC1423,
but support an additional external temperature sensor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'of_match_ptr' is defined in linux/of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/jc42.c:521:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/ltc4261.c:243:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/lm95234.c:704:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/max6697.c:649:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/max6642.c:299:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/ds1621.c:381:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/nct6775.c:3866:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Also introduce dev variable in probe function to simplify access
to client->dev, and use new macro ATTRIBUTE_GROUPS to declare
attribute groups.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Modify code to use is_visible to determine if an attribute should be created
or not, then use devm_hwmon_device_register_with_groups to create the hwmon
device and all attributes in one operation.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Also introduce new variable dev pointing to client->dev in the probe
function, and use new macro ATTRIBUTE_GROUPS to declare attribute groups.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Also rename new_client variable to client and introduce
new variable dev pointing to client->dev in the probe function,
and use new macro ATTRIBUTE_GROUPS to declare attribute groups.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drivers using the new hwmon_device_register_with_groups API often have a
remove function which consists solely of a call hwmon_device_unregister().
Provide support for devm_hwmon_device_register_with_groups and
devm_hwmon_device_unregister to allow this repeated code to be removed
and help eliminate error handling code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon_device_register_with_groups() lets callers register a hwmon device
together with all sysfs attributes in a single call.
When using hwmon_device_register_with_groups(), hwmon attributes are attached
to the hwmon device directly and no longer with its parent device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The f75375s driver crashes the kernel if it detects an an internal
implementation error. While the detected conditions suggest that
there is a bug in the code, the condition is not fatal.
Replace BUG() with WARN().
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
vid_to_reg() returns -1 if it encounters an error. Return -EINVAL instead.
Its only caller, atxp1_storevcore(), doesn't use the return code but
returns -1 instead, which is wrong anyway as it means -EPERM.
Use the return value from vid_to_reg() instead to report the error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
acpi_power_meter crashes the kernel if it detects an unexpected event
or an internal implementation error. While the detected conditions
suggest that there is a bug in the code, the condition is not fatal.
Replace BUG() with WARN().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
get_fan_speed_index() returns -EINVAL in case of errors, only to have it
ignored and replaced with -ENODEV. Make it return -ENODEV and use it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
find_trange_value() returns -ENODEV in case of errors, only to have it
ignored and replaced with -EINVAL. Make it return -EINVAL and use it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
pmbus code currently crashes the kernel if it detects an internal
implementation error. While the detected condition suggests that there
is a bug in the code, it is hardly fatal. Therefore, it should not
trigger a crash. Replace BUG() with WARN().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
smatch complains about
mc13783_adc_probe() error: snprintf() chops off the last chars of
'id->name': 20 +vs 10
Use PLATFORM_NAME_SIZE instead of '10' as size when declaring
the name variable.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
smatch complains about a potential out-of-bounds access to the
temp_offset array. That doesn't happen in practice, but it doesn't
hurt to add an explicit check either. This prevents potential problems
in the future (for example if the number of 'fixed' temperature
sensors is increased to add support for another chip).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
smatch complains that we don't use the return value from find_temp_source().
Valid point, only find_temp_source() doesn't return a valid error code.
Have it return a valid error code and use it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Semicolons after closing } of conditional blocks are not needed
and can be removed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
The crash reported and investigated in commit 5f4513 turned out to be
caused by a change to the read interface on newer (2012) SMCs.
Tests by Chris show that simply reading the data valid line is enough
for the problem to go away. Additional tests show that the newer SMCs
no longer wait for the number of requested bytes, but start sending
data right away. Apparently the number of bytes to read is no longer
specified as before, but instead found out by reading until end of
data. Failure to read until end of data confuses the state machine,
which eventually causes the crash.
As a remedy, assuming bit0 is the read valid line, make sure there is
nothing more to read before leaving the read function.
Tested to resolve the original problem, and runtested on MBA3,1,
MBP4,1, MBP8,2, MBP10,1, MBP10,2. The patch seems to have no effect on
machines before 2012.
Tested-by: Chris Murphy <chris@cmurf.com>
Cc: stable@vger.kernel.org
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using spi_w8r16be() instead of spi_w8r16() in this driver makes a code a bit
shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
After reports from Chris and Josh Boyer of a rare crash in applesmc,
Guenter pointed at the initialization problem fixed below. The patch
has not been verified to fix the crash, but should be applied
regardless.
Reported-by: <jwboyer@fedoraproject.org>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'break' after return or goto has no effect. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: T. Mertelj <tomaz.mertelj@guest.arnes.si>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Propagate appropriate error code obtained from ipmi_create_user()
instead of hardcoding.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
kstrtol() returns appropriate error values. Use those instead of
hardcoding. Silences several sparse messages of following type:
"why not propagate 'result' from kstrtol() instead of (-22)?"
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This gets rid of this warning:
drivers/hwmon/hwmon-vid.c: In function 'get_via_model_d_vrm':
drivers/hwmon/hwmon-vid.c:249:27: warning: variable 'dummy' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Pull hwmon fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (emc6w201) Do not declare enum variable
hwmon: (w83792d) Update module author
Fix the following smatch warning:
emc6w201.c:52:26: warning: symbol 'subfeature' was not declared.
Should it be static?
'enum { } subtype' declares an enum as (global) variable which we don't want.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
w83792d was written by me in 2004, I'd like to update my first name
into my current one to keep consistent, and delete invalid address.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for Fam16h (Kabini) to k10temp
Add support for NCT6102D/6106D and NCT6791D to nct6775 driver
Add support for ADS1115 to ads1015 driver
Add support for hibernate to w83627ehf and nct6775 drivers
Some minor cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=isg0
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for HTU21D (humidity sensor)
- add support for Fam16h (Kabini) to k10temp
- add support for NCT6102D/6106D and NCT6791D to nct6775 driver
- add support for ADS1115 to ads1015 driver
- add support for hibernate to w83627ehf and nct6775 drivers
- some minor cleanups
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (htu21) Add Measurement Specialties HTU21D support
hwmon: Change my email address.
hwmon: (k10temp) Add support for Fam16h (Kabini)
hwmon: (adt7462) ADT7462_REG_VOLT_MAX() should return 0
hwmon: (ads1015) Add support for ADS1115
hwmon: (w83627ehf) Add support for hibernate
hwmon: (nct6775) Add support for hibernate
hwmon: use dev_get_platdata()
hwmon: (nct6775) Fix size of data->temp array
hwmon: (nct6775) Avoid using device platform data outside probe function
hwmon: (nct6775) Add support for NCT6791D
hwmon: (nct6775) Add support for beep attributes
hwmon: (nct6775) Add support for critical low/high temperature limits on NCT6106
hwmon: (nct6775) Add support for NCT6102D/6106D
hwmon: (nct6775) Support two SuperIO chips in the same system
hwmon: (nct6775) Allocate attributes dynamically from templates
hwmon: (coretemp) Atom CPUs don't support TjMax; no warning needed
I've changed employers, so change the email addresses to match.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The temperature reporting interface stays the same, so we just
add the PCI-ID to the list.
Verified on AMD Olive Hill.
Signed-off-by: Wei Hu <wei@aristanetworks.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The callers never check for negative but they sometimes check for zero
returns:
int reg = ADT7462_REG_VOLT_MAX(data, i);
data->volt_max[i] =
(reg ? i2c_smbus_read_byte_data(client, reg) : 0);
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since the sht15 driver supports operation without an external vref
regulator the driver should use the new devm_regulator_get_optional() to
indicate that a stub regulator should not be provided.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for ads1115 device to ads1015 driver.
Based on work of Emiliano Carnati <carnatiatebneuro.com>.
Tested on ARM CPU based board.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hibernation uses its own set of callback functions, even if the code
is the same as the code used for suspend/restore.
Signed-off-by: Harald Judt <h.judt@gmx.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hibernation uses its own set of callback functions, even if the code
is the same as the code used for suspend/restore.
Signed-off-by: Harald Judt <h.judt@gmx.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Smatch complains that we have a array overflow:
drivers/hwmon/nct6775.c:1456 nct6775_update_device()
error: buffer overflow 'data->temp' 4 <= 4
Guenter Roeck says that the array should have been made larger in
7cbbd6aee6 (Add support for critical low/high temperature limits on
NCT6106). This patch does that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Plan going forward is to attach all device attributes to the hwmon device and no
longer to the platform device. With that change, accessing platform data outside
the probe function will be more difficult. To avoid the problem, change code
to no longer rely on it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Static attribute allocation is large and very repetitive.
Allocate attributes and attribute groups dynamically instead.
This reduces the size of the driver source by more than 600 lines,
and object size by more than 20k (more than 30%).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Display warning "Unable to read TjMax from CPU x" only if the CPU
is supposed to support it. This is not the case for the various Atom CPUs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In adt7470_write_word_data(), which writes two bytes using
i2c_smbus_write_byte_data(), the return codes are incorrectly AND-ed
together when they should be OR-ed together.
The return code of i2c_smbus_write_byte_data() is zero for success.
The upshot is only the first byte was ever written to the hardware.
The 2nd byte was never written out.
I noticed that trying to set the fan speed limits was not working
correctly on my system. Setting the fan speed limits is the only
code that uses adt7470_write_word_data(). After making the change
the limit settings work and the alarms work also.
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Without this patch, the values for ideality (register 0x4b) and ideality
selection mask (register 0x4c) are inverted.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the drivers/hwmon uses of the __cpuinit macros
from all C files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: lm-sensors@lm-sensors.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
abx500_temp_attributes is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
time_after (as opposed to time_after_equal) already ensures that the
cache lifetime is at least as much as requested. There is no point in
manually adding another jiffy to that value, and this can confuse the
reader into wrong interpretation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Imre Deak <imre.deak@intel.com>
time_after (as opposed to time_after_equal) already ensures that the
cache lifetime is at least as much as requested. There is no point in
manually adding another jiffy to that value, and this can confuse the
reader into wrong interpretation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Imre Deak <imre.deak@intel.com>
Add support for DS1631, DS1721, and DS1731 to ds1621 driver
Remove detect function from ds1621 driver as unreliable
Bug fixes in nct6775, iio_hwmon, and adm1021 drivers
Remove redundant platform_set_drvdata in various drivers
Add device tree support to ina2xx driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=OdGw
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver to support GMT G762/G763 pwm fan controllers
- add support for DS1631, DS1721, and DS1731 to ds1621 driver
- remove detect function from ds1621 driver as unreliable
- bug fixes in nct6775, iio_hwmon, and adm1021 drivers
- remove redundant platform_set_drvdata in various drivers
- add device tree support to ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ds1621) Fix temperature rounding operations
hwmon: (nct6775) Drop unsupported fan alarm attributes for NCT6775
hwmon: (nct6775) Fix temperature alarm attributes
Add support for GMT G762/G763 PWM fan controllers
hwmon: (ina2xx) Add device tree support to pass the shunt resistor
hwmon: (ds1621) Update documentation
hwmon: (ds1621) Add DS1731 chip support to ds1621 driver
hwmon: (iio_hwmon) add alias table
hwmon: (adm1021) Do not create min sysfs attributes for LM84
hwmon: (ds1621) Remove detect function
hwmon: (ds1621) Add ds1631 chip support to ds1621 driver and documentation
hwmon: (ds1621) Add ds1721 update interval sysfs attribute
hwmon: (ds1621) Add ds1721 chip support
hwmon: (w83627ehf) Remove redundant platform_set_drvdata()
hwmon: (ntc_thermistor) Remove redundant platform_set_drvdata()
hwmon: (i5k_amb) Remove redundant platform_set_drvdata()
hwmon: (coretemp) Remove redundant platform_set_drvdata()
hwmon: (abituguru3) Remove redundant platform_set_drvdata()
Calling kthread_run with a single name parameter causes it to be handled
as a format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit "hwmon: (ds1621) Add ds1721 chip support" broke rounding
for chips or configurations with less than 12 bit resolution.
Tested-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6775 does not support alarms for fans 4 and 5. Drop the attributes.
cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver displays wrong alarms for temperature attributes.
Turns out that temperature alarm bits are not fixed, but determined
by temperature source mapping. To fix the problem, walk through
the temperature sources to determine the correct alarm bit associated
with a given attribute.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
GMT G762/763 fan speed PWM controller is connected directly to a fan
and performs closed-loop or open-loop control of the fan speed. Two
modes - PWM or DC - are supported by the chip. Introduced driver
provides various knobs to control the operations of the chip (via
sysfs interface). Specific characteristics of the system can be passed
either using board init code or via DT. Documentation for both the
driver and DT bindings are also provided.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding another way that is device tree to pass the shunt resistor
value to driver except for platform data.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[Guenter Roeck: Added missing of.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These changes add DS1731 chip support to the ds1621 driver,
Kconfig, and documentation.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This helps the kernel to find the right module once the device is
created.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM84 does not support minimum temperature registers.
Only create the respective sysfs attributes for other chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Due to a lack of device and vendor identification registers, the
Dallas/Maxim DS16xx devices cannot be uniquely detected, sometimes
resulting in false positives. Therefore, the detect function is
being removed in favor of explicit device instantiation.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add definitions, information, and code for ds1631 chip support
to the ds1621 driver.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ds1721 device can be configured for 9..12 bit resolutions;
add a sysfs attribute for userspace to configure this attribute.
The definition, description, details, and usage are shown in the
documentation and were crafted from an LM73 driver patch done by
Chris Verges & Guenter Roeck).
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update the ds1621 documentation, driver, and Kconfig with
ds1721 chip support.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On a system with both MAX1617 and JC42 sensors, JC42 sensors can be misdetected
as LM84. Strengthen detection sufficiently enough to avoid this misdetection.
Also improve detection for ADM1021.
Modeled after chip detection code in sensors-detect command.
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
time_after (as opposed to time_after_equal) already ensures that the
cache lifetime is at least as much as requested. There is no point in
manually adding another jiffy to that value, and this can confuse the
reader into wrong interpretation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch fixes the null pointer dereference in goto error_release_channels
path when allocate memory for st fails.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Overtemperature and hysteresis registers only exist for primary
temperature registers, not for alternates, so do not assign
those registers when initializing alternates.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon update from Jean Delvare:
"Only lm75 driver updates this time"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (lm75) Add support for the Dallas/Maxim DS7505
hwmon: (lm75) Tune resolution and sample time per chip
hwmon: (lm75) Prepare to support per-chip resolution and sample time
hwmon: (lm75) Per-chip configuration register initialization
Basically it's the same as the original DS75 but much faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Most LM75-compatible chips can either sample much faster or with a
much better resolution than the original LM75 chip. So far the lm75
driver did not let the user take benefit of these improvements. Do it
now.
I decided to almost always configure the chip to use the best
resolution possible, which also means the longest sample time. The
only chips for which I didn't are the DS75, DS1775 and STDS75, because
they are really too slow in 12-bit mode (1.2 to 1.5 second worst case)
so I went for 11-bit mode as a more reasonable tradeoff. This choice is
dictated by the fact that the hwmon subsystem is meant for system
monitoring, it has never been supposed to be ultra-fast, and as a
matter of fact we do cache the sampled values in almost all drivers.
If anyone isn't pleased with these default settings, they can always
introduce a platform data structure or DT support for the lm75. That
being said, it seems nobody ever complained that the driver wouldn't
refresh the value faster than every 1.5 second, and the change made
it faster for all chips even in 12-bit mode, so I don't expect any
complaint.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Prepare the lm75 driver to support per-chip resolution and sample
time. For now we only make the code generic enough to support it, but
we still use the same, unchanged resolution (9-bit) and sample time
(1.5 s) for all chips.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
There is no standard for the configuration register bits of LM75-like
chips. We shouldn't blindly clear bits setting the resolution as they
are either unused or used for something else on some of the supported
chips.
So, switch to per-chip configuration initialization. This will allow
for better tuning later, for example using more resolution bits when
available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
- OpenFirmware/DeviceTree support for the Power Supply core: the core now
automatically populates supplied_from hierarchy from the device tree.
With these patches chargers and batteries can now lookup each other
without the board files support shim. Rhyland Klein at NVIDIA did the
work;
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using the
AB85xx core and depends on some recent changes to it, so that is why the
driver comes through the battery tree. It has an appropriate ack from
the hwmon maintainer (i.e. Guenter Roeck). Martin Persson at ST-Ericsson
and Hongbo Zhang at Linaro authored the driver;
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The changes
touch mfd parts, but these were acked by the appropriate MFD maintainer
(i.e. Samuel Ortiz). Lee Jones at Linaro did most of the work and lead
the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones;
- Versatile Express poweroff driver moved into drivers/power/reset/.
- Tree-wise: use devm_kzalloc() where appropriate;
- Tree-wise: dev_pm_ops cleanups/fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=5BdE
-----END PGP SIGNATURE-----
Merge tag 'for-v3.10' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Highlights:
- OpenFirmware/DeviceTree support for the Power Supply core: the core
now automatically populates supplied_from hierarchy from the device
tree. With these patches chargers and batteries can now lookup
each other without the board files support shim. Rhyland Klein at
NVIDIA did the work
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using
the AB85xx core and depends on some recent changes to it, so that
is why the driver comes through the battery tree. It has an
appropriate ack from the hwmon maintainer (i.e. Guenter Roeck).
Martin Persson at ST-Ericsson and Hongbo Zhang at Linaro authored
the driver
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The
changes touch mfd parts, but these were acked by the appropriate
MFD maintainer (ie Samuel Ortiz). Lee Jones at Linaro did most of
the work and lead the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones
- Versatile Express poweroff driver moved into drivers/power/reset/
- Tree-wide: use devm_kzalloc() where appropriate
- Tree-wide: dev_pm_ops cleanups/fixes"
* tag 'for-v3.10' of git://git.infradead.org/battery-2.6: (112 commits)
pm2301-charger: Fix suspend/resume
charger-manager: Use kmemdup instead of kzalloc + memcpy
power_supply: Populate supplied_from hierarchy from the device tree
power_supply: Add core support for supplied_from
power_supply: Define Binding for power-supplies
rx51_battery: Fix reporting temperature
hwmon: Add ST-Ericsson ABX500 hwmon driver
ab8500_bmdata: Export abx500_res_to_temp tables for hwmon
ab8500_{bmdata,fg}: Add const attributes to some data arrays
ab8500_bmdata: Eliminate CamelCase warning of some variables
ab8500_btemp: Make ab8500_btemp_get* interfaces public
goldfish_battery: Use resource_size()
lp8788-charger: Use PAGE_SIZE for the sysfs read operation
max8925_power: Use devm_kzalloc()
da9030_battery: Use devm_kzalloc()
da9052-battery: Use devm_kzalloc()
ds2760_battery: Use devm_kzalloc()
ds2780_battery: Use devm_kzalloc()
gpio-charger: Use devm_kzalloc()
isp1704_charger: Use devm_kzalloc()
...
Here's the big staging driver tree update for 3.10-rc1
This update contains loads of comedi driver cleanups and fixes in here,
iio updates, android driver changes, and other various staging driver
cleanups.
Thanks to some drivers being removed, and the comedi driver cleanups, we
have removed more code than we added:
627 files changed, 65145 insertions(+), 76321 deletions(-)
which is always nice to see.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+nF8ACgkQMUfUDdst+ynlIwCfYm2pSkA0w1K56mftq1T0hpMH
b9IAmwQlfEHSIKeAxqRO3RRrfLu5XD7L
=Jnxr
-----END PGP SIGNATURE-----
Merge tag 'staging-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver tree update from Greg Kroah-Hartman:
"Here's the big staging driver tree update for 3.10-rc1
This update contains loads of comedi driver cleanups and fixes in
here, iio updates, android driver changes, and other various staging
driver cleanups.
Thanks to some drivers being removed, and the comedi driver cleanups,
we have removed more code than we added:
627 files changed, 65145 insertions(+), 76321 deletions(-)
which is always nice to see.
All of these have been in linux-next for a while."
* tag 'staging-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (940 commits)
staging: comedi: ni_labpc: fix legacy driver build
staging: comedi: das800: cleanup the cio-das802/16 fifo comments
staging: comedi: das800: rename CamelCase vars in das800_ai_do_cmd()
staging: comedi: das800: tidy up the private data
staging: comedi: das800: tidy up das800_interrupt()
staging: comedi: das800: tidy up das800_ai_insn_read()
staging: comedi: das800: tidy up das800_di_insn_bits()
staging: comedi: das800: tidy up das800_do_insn_bits()
staging: comedi: das800: remove extra divisor calculation call
staging: comedi: das800: rename {enable,disable}_das800
staging: comedi: das800: tidy up subdevice init
staging: comedi: das800: allow attaching without interrupt support
staging: comedi: das800: interrupts are required for async command support
staging: comedi: das800: tidy up das800_ai_do_cmdtest()
staging: comedi: das800: remove 'volatile' on private data variables
staging: comedi: das800: cleanup the boardinfo
staging: comedi: das800: cleanup range table declarations
staging: comedi: das800: introduce das800_ind_{write, read}()
staging: comedi: das800: remove forward declarations
staging: comedi: das800: move das800_set_frequency()
...
TMP432 is similar to TMP431 with a second external temperature sensor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cached data is no longer valid after resetting the temperature history.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Use two-dimensional array pointing to registers
Merge temperature and limit access functions into a single function
Return error codes from I2C reads
Use DIV_ROUND_CLOSEST for rounding operations and improve rounding
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Each of ST-Ericsson X500 chip set series consists of both ABX500 and DBX500
chips. This is ABX500 hwmon driver, where the abx500.c is a common layer for
all ABX500s, and the ab8500.c is specific for AB8500 chip. Under this designed
structure, other chip specific files can be added simply using the same common
layer abx500.c.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This ensures that the loop iterations are correct even if/when
the number of elements in an array changes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per datasheet, VIN3 and AUXTIN share the same external pin. However, there
is no clean way to detect this condition. Furthermore, both are reported
by the BIOS on Supermicro C7H61. It may thus be possible that chip revisions
exist where both attributes are supported at the same time.
Better play safe and report both.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6775, NCT6776, and NCT6779 have a number of variants with the same
chip ID but different chip labels. Add text "or compatible" to the
message displayed when the driver is loaded and rephrase the Kconfig
entry to reflect that it also supports compatible chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and reduce object size by more than 300 bytes (x86_64).
Cc: Jamie Lentin <jm@lentin.co.uk>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Turns out that TMP411B and TMP411C have different and unique device IDs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Arnaud Ebalard