Some platforms, such as mips64, don't map __u64 to long long unsigned
int so using %llu produces a warning:
gpio-event-mon.c:110:37: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
110 | fprintf(stdout, "GPIO EVENT at %llu on line %d (%d|%d) ",
| ~~~^
| |
| long long unsigned int
| %lu
111 | event.timestamp_ns, event.offset, event.line_seqno,
| ~~~~~~~~~~~~~~~~~~
| |
| __u64 {aka long unsigned int}
Replace the %llu with PRIu64 and cast the argument to uint64_t.
Fixes: 03fd11b033 ("tools/gpio/gpio-event-mon: fix warning")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
For addressing the regression on Pioneer devices, we recently
corrected the quirk code to enable the implicit feedback mode on those
devices properly. However, the devices still showed problems with the
full duplex operations with JACK, and after debug sessions, we figured
out that the older kernels that had worked with JACK also didn't use
the implicit feedback mode at all although they had the quirk code to
enable it; instead, the old code worked just to skip the normal sync
endpoint setup that would have been detected without it. IOW, what
broke without the implicit-fb quirk in the past was the application of
the normal sync endpoint that is actually the capture data endpoint on
these devices.
This patch covers the overseen piece: it modifies the quirk code again
not to enable the implicit feedback mode but just to make the driver
skipping the sync endpoint detection. This made the driver working
with JACK full-duplex mode again.
Still it's not quite clear why the implicit feedback doesn't work on
those devices yet; maybe it's about some issues in the URB setup. But
at least, with this patch, the driver should work in the level of the
older kernels again.
Fixes: 167c9dc84e ("ALSA: usb-audio: Fix implicit feedback sync setup for Pioneer devices")
Link: https://lore.kernel.org/r/20210118075816.25068-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAC2/3 sample rate setup is based on the clock node, which is
usually shared in the interface, and can't be re-setup without
deselecting the interface once, and that's how the current code
behaves. OTOH, the sample rate setup of UAC1 is per endpoint, hence
we basically need to call for each endpoint usage even if those share
the same interface.
This patch fixes the behavior of UAC1 to call always
snd_usb_init_sample_rate() in snd_usb_endpoint_configure().
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/20210118075816.25068-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current sample rate setup function for UAC1 assumes only the first
endpoint retrieved from the interface:altset pair, but the rate set up
may be needed also for the secondary endpoint. Also, retrieving the
endpoint number from the interface descriptor is redundant; we have
already the target endpoint in the given audioformat object.
This patch simplifies the code and corrects the target endpoint as
described in the above. It simply refers to fmt->endpoint directly.
Also, this patch drops the pioneer_djm_set_format_quirk() that is
caleld from snd_usb_set_format_quirk(); this function does the sample
rate setup but for the capture endpoint (0x82), and that's exactly
what the change above fixes.
Link: https://lore.kernel.org/r/20210118075816.25068-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The only flag we really need is __GFP_NOMEMALLOC, highmem depends on
dma32 and moveable/compound should never be set in the first place.
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/413812/
Link: https://patchwork.freedesktop.org/patch/413964/
Fixes: d099fc8f54 ("drm/ttm: new TT backend allocation pool v3")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Get DRM connector reference count while scheduling a prop work
to avoid any possible destroy of DRM connector when it is in
DRM_CONNECTOR_REGISTERED state.
Fixes: a6597faa2d ("drm/i915: Protect workers against disappearing connectors")
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-3-anshuman.gupta@intel.com
(cherry picked from commit b3c6661aad)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When crtc state need_modeset is true it is not necessary
it is going to be a real modeset, it can turns to be a
fastset instead of modeset.
This turns content protection property to be DESIRED and hdcp
update_pipe left with property to be in DESIRED state but
actual hdcp->value was ENABLED.
This issue is caught with DP MST setup, where we have multiple
connector in same DP_MST topology. When disabling HDCP on one of
DP MST connector leads to set the crtc state need_modeset to true
for all other crtc driving the other DP-MST topology connectors.
This turns up other DP MST connectors CP property to be DESIRED
despite the actual hdcp->value is ENABLED.
Above scenario fails the DP MST HDCP IGT test, disabling HDCP on
one MST stream should not cause to disable HDCP on another MST
stream on same DP MST topology.
v2:
- Fixed connector->base.registration_state == DRM_CONNECTOR_REGISTERED
WARN_ON.
v3:
- Commit log improvement. [Uma]
- Added a comment before scheduling prop_work. [Uma]
Fixes: 33f9a623bf ("drm/i915/hdcp: Update CP as per the kernel internal state")
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-2-anshuman.gupta@intel.com
(cherry picked from commit d276e16702)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix build error in x86/xen/ when PARAVIRT_SPINLOCKS is not enabled.
Fixes this build error:
../arch/x86/xen/smp_hvm.c: In function ‘xen_hvm_smp_init’:
../arch/x86/xen/smp_hvm.c:77:3: error: ‘nopvspin’ undeclared (first use in this function)
nopvspin = true;
Fixes: 3d7746bea9 ("x86/xen: Fix xen_hvm_smp_init() when vector callback not available")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20210115191123.27572-1-rdunlap@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Fix the follow warnings:
./fs/cifs/connect.c: WARNING: Comparison of 0/1 to bool variable
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Fix the following coccicheck warnings:
./fs/cifs/connect.c:3386:2-21: WARNING: Assignment of 0/1 to
bool variable.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
- Fix 'CPU too large' error in Intel PT.
- Correct event attribute sizes in 'perf inject'.
- Sync build_bug.h and kvm.h kernel copies.
- Fix bpf.h header include directive in 5sec.c 'perf trace' bpf example.
- libbpf tests fixes.
- Fix shadow stat 'perf test' for non-bash shells.
- Take cgroups into account for shadow stats in 'perf stat'.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Test results:
The first ones are container based builds of tools/perf with and without libelf
support. Where clang is available, it is also used to build perf with/without
libelf, and building with LIBCLANGLLVM=1 (built-in clang) with gcc and clang
when clang and its devel libraries are installed.
The objtool and samples/bpf/ builds are disabled now that I'm switching from
using the sources in a local volume to fetching them from a http server to
build it inside the container, to make it easier to build in a container cluster.
Those will come back later.
Several are cross builds, the ones with -x-ARCH and the android one, and those
may not have all the features built, due to lack of multi-arch devel packages,
available and being used so far on just a few, like
debian:experimental-x-{arm64,mipsel}.
The 'perf test' one will perform a variety of tests exercising
tools/perf/util/, tools/lib/{bpf,traceevent,etc}, as well as run perf commands
with a variety of command line event specifications to then intercept the
sys_perf_event syscall to check that the perf_event_attr fields are set up as
expected, among a variety of other unit tests.
Then there is the 'make -C tools/perf build-test' ones, that build tools/perf/
with a variety of feature sets, exercising the build with an incomplete set of
features as well as with a complete one. It is planned to have it run on each
of the containers mentioned above, using some container orchestration
infrastructure. Get in contact if interested in helping having this in place.
$ grep "model name" -m1 /proc/cpuinfo
model name: AMD Ryzen 9 3900X 12-Core Processor
# export PERF_TARBALL=http://192.168.86.5/perf/perf-5.11.0-rc3.tar.xz
# dm
1 66.93 alpine:3.4 : Ok gcc (Alpine 5.3.0) 5.3.0, clang version 3.8.0 (tags/RELEASE_380/final)
2 68.65 alpine:3.5 : Ok gcc (Alpine 6.2.1) 6.2.1 20160822, clang version 3.8.1 (tags/RELEASE_381/final)
3 73.00 alpine:3.6 : Ok gcc (Alpine 6.3.0) 6.3.0, clang version 4.0.0 (tags/RELEASE_400/final)
4 79.04 alpine:3.7 : Ok gcc (Alpine 6.4.0) 6.4.0, Alpine clang version 5.0.0 (tags/RELEASE_500/final) (based on LLVM 5.0.0)
5 79.71 alpine:3.8 : Ok gcc (Alpine 6.4.0) 6.4.0, Alpine clang version 5.0.1 (tags/RELEASE_501/final) (based on LLVM 5.0.1)
6 82.51 alpine:3.9 : Ok gcc (Alpine 8.3.0) 8.3.0, Alpine clang version 5.0.1 (tags/RELEASE_502/final) (based on LLVM 5.0.1)
7 103.45 alpine:3.10 : Ok gcc (Alpine 8.3.0) 8.3.0, Alpine clang version 8.0.0 (tags/RELEASE_800/final) (based on LLVM 8.0.0)
8 113.86 alpine:3.11 : Ok gcc (Alpine 9.3.0) 9.3.0, Alpine clang version 9.0.0 (https://git.alpinelinux.org/aports f7f0d2c2b8bcd6a5843401a9a702029556492689) (based on LLVM 9.0.0)
9 109.31 alpine:3.12 : Ok gcc (Alpine 9.3.0) 9.3.0, Alpine clang version 10.0.0 (https://gitlab.alpinelinux.org/alpine/aports.git 7445adce501f8473efdb93b17b5eaf2f1445ed4c)
10 113.90 alpine:edge : Ok gcc (Alpine 10.2.0) 10.2.0, Alpine clang version 10.0.1
11 66.76 alt:p8 : Ok x86_64-alt-linux-gcc (GCC) 5.3.1 20151207 (ALT p8 5.3.1-alt3.M80P.1), clang version 3.8.0 (tags/RELEASE_380/final)
12 83.71 alt:p9 : Ok x86_64-alt-linux-gcc (GCC) 8.4.1 20200305 (ALT p9 8.4.1-alt0.p9.1), clang version 10.0.0
13 80.70 alt:sisyphus : Ok x86_64-alt-linux-gcc (GCC) 9.3.1 20200518 (ALT Sisyphus 9.3.1-alt1), clang version 10.0.1
14 62.75 amazonlinux:1 : Ok gcc (GCC) 7.2.1 20170915 (Red Hat 7.2.1-2), clang version 3.6.2 (tags/RELEASE_362/final)
15 97.65 amazonlinux:2 : Ok gcc (GCC) 7.3.1 20180712 (Red Hat 7.3.1-12), clang version 7.0.1 (Amazon Linux 2 7.0.1-1.amzn2.0.2)
16 21.18 android-ndk:r12b-arm : Ok arm-linux-androideabi-gcc (GCC) 4.9.x 20150123 (prerelease)
17 21.07 android-ndk:r15c-arm : Ok arm-linux-androideabi-gcc (GCC) 4.9.x 20150123 (prerelease)
18 25.83 centos:6 : Ok gcc (GCC) 4.4.7 20120313 (Red Hat 4.4.7-23)
19 30.65 centos:7 : Ok gcc (GCC) 4.8.5 20150623 (Red Hat 4.8.5-44)
20 93.44 centos:8 : Ok gcc (GCC) 8.3.1 20191121 (Red Hat 8.3.1-5), clang version 10.0.1 (Red Hat 10.0.1-1.module_el8.3.0+467+cb298d5b)
21 60.64 clearlinux:latest : Ok gcc (Clear Linux OS for Intel Architecture) 10.2.1 20201217 releases/gcc-10.2.0-643-g7cbb07d2fc, clang version 10.0.1
22 74.57 debian:8 : Ok gcc (Debian 4.9.2-10+deb8u2) 4.9.2, Debian clang version 3.5.0-10 (tags/RELEASE_350/final) (based on LLVM 3.5.0)
23 75.40 debian:9 : Ok gcc (Debian 6.3.0-18+deb9u1) 6.3.0 20170516, clang version 3.8.1-24 (tags/RELEASE_381/final)
24 72.75 debian:10 : Ok gcc (Debian 8.3.0-6) 8.3.0, clang version 7.0.1-8+deb10u2 (tags/RELEASE_701/final)
25 72.36 debian:experimental : Ok gcc (Debian 10.2.1-6) 10.2.1 20210110, Debian clang version 11.0.1-2
26 32.35 debian:experimental-x-arm64 : Ok aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110
27 28.65 debian:experimental-x-mips64 : Ok mips64-linux-gnuabi64-gcc (Debian 10.2.1-3) 10.2.1 20201224
28 13.79 debian:experimental-x-mipsel : FAIL mipsel-linux-gnu-gcc (Debian 10.2.1-3) 10.2.1 20201224
CC /tmp/build/perf/util/map.o
util/map.c: In function 'map__new':
util/map.c:109:5: error: '%s' directive output may be truncated writing between 1 and 2147483645 bytes into a region of size 4096 [-Werror=format-truncation=]
109 | "%s/platforms/%s/arch-%s/usr/lib/%s",
| ^~
In file included from /usr/mipsel-linux-gnu/include/stdio.h:867,
from util/symbol.h:11,
from util/map.c:2:
/usr/mipsel-linux-gnu/include/bits/stdio2.h:67:10: note: '__builtin___snprintf_chk' output 32 or more bytes (assuming 4294967321) into a destination of size 4096
67 | return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
68 | __bos (__s), __fmt, __va_arg_pack ());
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
29 29.14 fedora:20 : Ok gcc (GCC) 4.8.3 20140911 (Red Hat 4.8.3-7)
30 30.66 fedora:22 : Ok gcc (GCC) 5.3.1 20160406 (Red Hat 5.3.1-6), clang version 3.5.0 (tags/RELEASE_350/final)
31 66.33 fedora:23 : Ok gcc (GCC) 5.3.1 20160406 (Red Hat 5.3.1-6), clang version 3.7.0 (tags/RELEASE_370/final)
32 77.51 fedora:24 : Ok gcc (GCC) 6.3.1 20161221 (Red Hat 6.3.1-1), clang version 3.8.1 (tags/RELEASE_381/final)
33 25.23 fedora:24-x-ARC-uClibc : Ok arc-linux-gcc (ARCompact ISA Linux uClibc toolchain 2017.09-rc2) 7.1.1 20170710
34 79.68 fedora:25 : Ok gcc (GCC) 6.4.1 20170727 (Red Hat 6.4.1-1), clang version 3.9.1 (tags/RELEASE_391/final)
35 93.09 fedora:26 : Ok gcc (GCC) 7.3.1 20180130 (Red Hat 7.3.1-2), clang version 4.0.1 (tags/RELEASE_401/final)
36 94.12 fedora:27 : Ok gcc (GCC) 7.3.1 20180712 (Red Hat 7.3.1-6), clang version 5.0.2 (tags/RELEASE_502/final)
37 101.97 fedora:28 : Ok gcc (GCC) 8.3.1 20190223 (Red Hat 8.3.1-2), clang version 6.0.1 (tags/RELEASE_601/final)
38 107.51 fedora:29 : Ok gcc (GCC) 8.3.1 20190223 (Red Hat 8.3.1-2), clang version 7.0.1 (Fedora 7.0.1-6.fc29)
39 111.24 fedora:30 : Ok gcc (GCC) 9.3.1 20200408 (Red Hat 9.3.1-2), clang version 8.0.0 (Fedora 8.0.0-3.fc30)
40 25.85 fedora:30-x-ARC-uClibc : Ok arc-linux-gcc (ARCv2 ISA Linux uClibc toolchain 2019.03-rc1) 8.3.1 20190225
41 110.61 fedora:31 : Ok gcc (GCC) 9.3.1 20200408 (Red Hat 9.3.1-2), clang version 9.0.1 (Fedora 9.0.1-4.fc31)
42 93.78 fedora:32 : Ok gcc (GCC) 10.2.1 20201016 (Red Hat 10.2.1-6), clang version 10.0.1 (Fedora 10.0.1-3.fc32)
43 91.51 fedora:33 : Ok gcc (GCC) 10.2.1 20201125 (Red Hat 10.2.1-9), clang version 11.0.0 (Fedora 11.0.0-2.fc33)
44 92.75 fedora:34 : Ok gcc (GCC) 11.0.0 20210113 (Red Hat 11.0.0-0), clang version 11.0.1 (Fedora 11.0.1-4.fc34)
45 92.33 fedora:rawhide : Ok gcc (GCC) 11.0.0 20210109 (Red Hat 11.0.0-0), clang version 11.0.1 (Fedora 11.0.1-4.fc34)
46 33.58 gentoo-stage3-amd64:latest : Ok gcc (Gentoo 9.3.0-r1 p3) 9.3.0
47 66.03 mageia:5 : Ok gcc (GCC) 4.9.2, clang version 3.5.2 (tags/RELEASE_352/final)
48 84.73 mageia:6 : Ok gcc (Mageia 5.5.0-1.mga6) 5.5.0, clang version 3.9.1 (tags/RELEASE_391/final)
49 98.35 manjaro:latest : Ok gcc (GCC) 10.2.0, clang version 10.0.1
50 223.15 openmandriva:cooker : Ok gcc (GCC) 10.2.0 20200723 (OpenMandriva), OpenMandriva 11.0.0-1 clang version 11.0.0 (/builddir/build/BUILD/llvm-project-llvmorg-11.0.0/clang 63e22714ac938c6b537bd958f70680d3331a2030)
51 117.30 opensuse:15.0 : Ok gcc (SUSE Linux) 7.4.1 20190905 [gcc-7-branch revision 275407], clang version 5.0.1 (tags/RELEASE_501/final 312548)
52 124.82 opensuse:15.1 : Ok gcc (SUSE Linux) 7.5.0, clang version 7.0.1 (tags/RELEASE_701/final 349238)
53 113.33 opensuse:15.2 : Ok gcc (SUSE Linux) 7.5.0, clang version 9.0.1
54 106.17 opensuse:42.3 : Ok gcc (SUSE Linux) 4.8.5, clang version 3.8.0 (tags/RELEASE_380/final 262553)
55 108.15 opensuse:tumbleweed : Ok gcc (SUSE Linux) 10.2.1 20200825 [revision c0746a1beb1ba073c7981eb09f55b3d993b32e5c], clang version 10.0.1
56 25.57 oraclelinux:6 : Ok gcc (GCC) 4.4.7 20120313 (Red Hat 4.4.7-23.0.1)
57 30.86 oraclelinux:7 : Ok gcc (GCC) 4.8.5 20150623 (Red Hat 4.8.5-44.0.3)
58 91.75 oraclelinux:8 : Ok gcc (GCC) 8.3.1 20191121 (Red Hat 8.3.1-5.0.1), clang version 10.0.1 (Red Hat 10.0.1-1.0.1.module+el8.3.0+7827+89335dbf)
59 27.64 ubuntu:12.04 : Ok gcc (Ubuntu/Linaro 4.6.3-1ubuntu5) 4.6.3, Ubuntu clang version 3.0-6ubuntu3 (tags/RELEASE_30/final) (based on LLVM 3.0)
60 29.65 ubuntu:14.04 : Ok gcc (Ubuntu 4.8.4-2ubuntu1~14.04.4) 4.8.4
61 75.65 ubuntu:16.04 : Ok gcc (Ubuntu 5.4.0-6ubuntu1~16.04.12) 5.4.0 20160609, clang version 3.8.0-2ubuntu4 (tags/RELEASE_380/final)
62 25.57 ubuntu:16.04-x-arm : Ok arm-linux-gnueabihf-gcc (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) 5.4.0 20160609
63 25.52 ubuntu:16.04-x-arm64 : Ok aarch64-linux-gnu-gcc (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) 5.4.0 20160609
64 25.01 ubuntu:16.04-x-powerpc : Ok powerpc-linux-gnu-gcc (Ubuntu 5.4.0-6ubuntu1~16.04.9) 5.4.0 20160609
65 25.51 ubuntu:16.04-x-powerpc64 : Ok powerpc64-linux-gnu-gcc (Ubuntu/IBM 5.4.0-6ubuntu1~16.04.9) 5.4.0 20160609
66 25.70 ubuntu:16.04-x-powerpc64el : Ok powerpc64le-linux-gnu-gcc (Ubuntu/IBM 5.4.0-6ubuntu1~16.04.9) 5.4.0 20160609
67 24.95 ubuntu:16.04-x-s390 : Ok s390x-linux-gnu-gcc (Ubuntu 5.4.0-6ubuntu1~16.04.9) 5.4.0 20160609
68 87.96 ubuntu:18.04 : Ok gcc (Ubuntu 7.5.0-3ubuntu1~18.04) 7.5.0, clang version 6.0.0-1ubuntu2 (tags/RELEASE_600/final)
69 27.40 ubuntu:18.04-x-arm : Ok arm-linux-gnueabihf-gcc (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04) 7.5.0
70 27.14 ubuntu:18.04-x-arm64 : Ok aarch64-linux-gnu-gcc (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04) 7.5.0
71 22.68 ubuntu:18.04-x-m68k : Ok m68k-linux-gnu-gcc (Ubuntu 7.5.0-3ubuntu1~18.04) 7.5.0
72 26.52 ubuntu:18.04-x-powerpc : Ok powerpc-linux-gnu-gcc (Ubuntu 7.5.0-3ubuntu1~18.04) 7.5.0
73 28.97 ubuntu:18.04-x-powerpc64 : Ok powerpc64-linux-gnu-gcc (Ubuntu 7.5.0-3ubuntu1~18.04) 7.5.0
74 28.54 ubuntu:18.04-x-powerpc64el : Ok powerpc64le-linux-gnu-gcc (Ubuntu 7.5.0-3ubuntu1~18.04) 7.5.0
75 163.57 ubuntu:18.04-x-riscv64 : Ok riscv64-linux-gnu-gcc (Ubuntu 7.5.0-3ubuntu1~18.04) 7.5.0
76 24.07 ubuntu:18.04-x-s390 : Ok s390x-linux-gnu-gcc (Ubuntu 7.5.0-3ubuntu1~18.04) 7.5.0
77 26.77 ubuntu:18.04-x-sh4 : Ok sh4-linux-gnu-gcc (Ubuntu 7.5.0-3ubuntu1~18.04) 7.5.0
78 24.00 ubuntu:18.04-x-sparc64 : Ok sparc64-linux-gnu-gcc (Ubuntu 7.5.0-3ubuntu1~18.04) 7.5.0
79 69.36 ubuntu:19.10 : Ok gcc (Ubuntu 9.2.1-9ubuntu2) 9.2.1 20191008, clang version 8.0.1-3build1 (tags/RELEASE_801/final)
80 27.07 ubuntu:19.10-x-alpha : Ok alpha-linux-gnu-gcc (Ubuntu 9.2.1-9ubuntu1) 9.2.1 20191008
81 24.29 ubuntu:19.10-x-hppa : Ok hppa-linux-gnu-gcc (Ubuntu 9.2.1-9ubuntu1) 9.2.1 20191008
82 74.99 ubuntu:20.04 : Ok gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, clang version 10.0.0-4ubuntu1
83 30.49 ubuntu:20.04-x-powerpc64el : Ok powerpc64le-linux-gnu-gcc (Ubuntu 10.2.0-5ubuntu1~20.04) 10.2.0
84 73.54 ubuntu:20.10 : Ok gcc (Ubuntu 10.2.0-13ubuntu1) 10.2.0, Ubuntu clang version 11.0.0-2
$
# uname -a
Linux quaco 5.10.7-100.fc32.x86_64 #1 SMP Tue Jan 12 20:25:28 UTC 2021 x86_64 x86_64 x86_64 GNU/Linux
# git log --oneline -1
648b054a46 perf inject: Correct event attribute sizes
# perf version --build-options
perf version 5.11.rc3.g648b054a4647
dwarf: [ on ] # HAVE_DWARF_SUPPORT
dwarf_getlocations: [ on ] # HAVE_DWARF_GETLOCATIONS_SUPPORT
glibc: [ on ] # HAVE_GLIBC_SUPPORT
syscall_table: [ on ] # HAVE_SYSCALL_TABLE_SUPPORT
libbfd: [ on ] # HAVE_LIBBFD_SUPPORT
libelf: [ on ] # HAVE_LIBELF_SUPPORT
libnuma: [ on ] # HAVE_LIBNUMA_SUPPORT
numa_num_possible_cpus: [ on ] # HAVE_LIBNUMA_SUPPORT
libperl: [ on ] # HAVE_LIBPERL_SUPPORT
libpython: [ on ] # HAVE_LIBPYTHON_SUPPORT
libslang: [ on ] # HAVE_SLANG_SUPPORT
libcrypto: [ on ] # HAVE_LIBCRYPTO_SUPPORT
libunwind: [ on ] # HAVE_LIBUNWIND_SUPPORT
libdw-dwarf-unwind: [ on ] # HAVE_DWARF_SUPPORT
zlib: [ on ] # HAVE_ZLIB_SUPPORT
lzma: [ on ] # HAVE_LZMA_SUPPORT
get_cpuid: [ on ] # HAVE_AUXTRACE_SUPPORT
bpf: [ on ] # HAVE_LIBBPF_SUPPORT
aio: [ on ] # HAVE_AIO_SUPPORT
zstd: [ on ] # HAVE_ZSTD_SUPPORT
libpfm4: [ OFF ] # HAVE_LIBPFM
# perf test
1: vmlinux symtab matches kallsyms : Ok
2: Detect openat syscall event : Ok
3: Detect openat syscall event on all cpus : Ok
4: Read samples using the mmap interface : Ok
5: Test data source output : Ok
6: Parse event definition strings : Ok
7: Simple expression parser : Ok
8: PERF_RECORD_* events & perf_sample fields : Ok
9: Parse perf pmu format : Ok
10: PMU events :
10.1: PMU event table sanity : Ok
10.2: PMU event map aliases : Ok
10.3: Parsing of PMU event table metrics : Ok
10.4: Parsing of PMU event table metrics with fake PMUs : Ok
11: DSO data read : Ok
12: DSO data cache : Ok
13: DSO data reopen : Ok
14: Roundtrip evsel->name : Ok
15: Parse sched tracepoints fields : Ok
16: syscalls:sys_enter_openat event fields : Ok
17: Setup struct perf_event_attr : Ok
18: Match and link multiple hists : Ok
19: 'import perf' in python : Ok
20: Breakpoint overflow signal handler : Ok
21: Breakpoint overflow sampling : Ok
22: Breakpoint accounting : Ok
23: Watchpoint :
23.1: Read Only Watchpoint : Skip (missing hardware support)
23.2: Write Only Watchpoint : Ok
23.3: Read / Write Watchpoint : Ok
23.4: Modify Watchpoint : Ok
24: Number of exit events of a simple workload : Ok
25: Software clock events period values : Ok
26: Object code reading : Ok
27: Sample parsing : Ok
28: Use a dummy software event to keep tracking : Ok
29: Parse with no sample_id_all bit set : Ok
30: Filter hist entries : Ok
31: Lookup mmap thread : Ok
32: Share thread maps : Ok
33: Sort output of hist entries : Ok
34: Cumulate child hist entries : Ok
35: Track with sched_switch : Ok
36: Filter fds with revents mask in a fdarray : Ok
37: Add fd to a fdarray, making it autogrow : Ok
38: kmod_path__parse : Ok
39: Thread map : Ok
40: LLVM search and compile :
40.1: Basic BPF llvm compile : Ok
40.2: kbuild searching : Ok
40.3: Compile source for BPF prologue generation : Ok
40.4: Compile source for BPF relocation : Ok
41: Session topology : Ok
42: BPF filter :
42.1: Basic BPF filtering : Ok
42.2: BPF pinning : Ok
42.3: BPF prologue generation : Ok
42.4: BPF relocation checker : Ok
43: Synthesize thread map : Ok
44: Remove thread map : Ok
45: Synthesize cpu map : Ok
46: Synthesize stat config : Ok
47: Synthesize stat : Ok
48: Synthesize stat round : Ok
49: Synthesize attr update : Ok
50: Event times : Ok
51: Read backward ring buffer : Ok
52: Print cpu map : Ok
53: Merge cpu map : Ok
54: Probe SDT events : Ok
55: is_printable_array : Ok
56: Print bitmap : Ok
57: perf hooks : Ok
58: builtin clang support : Skip (not compiled in)
59: unit_number__scnprintf : Ok
60: mem2node : Ok
61: time utils : Ok
62: Test jit_write_elf : Ok
63: Test libpfm4 support : Skip (not compiled in)
64: Test api io : Ok
65: maps__merge_in : Ok
66: Demangle Java : Ok
67: Parse and process metrics : Ok
68: PE file support : Ok
69: Event expansion for cgroups : Ok
70: Convert perf time to TSC : Ok
71: x86 rdpmc : Ok
72: DWARF unwind : Ok
73: x86 instruction decoder - new instructions : Ok
74: Intel PT packet decoder : Ok
75: x86 bp modify : Ok
76: probe libc's inet_pton & backtrace it with ping : Ok
77: Use vfs_getname probe to get syscall args filenames : Ok
78: Check Arm CoreSight trace data recording and synthesized samples: Skip
79: perf stat metrics (shadow stat) test : Ok
80: build id cache operations : Ok
81: Add vfs_getname probe to get syscall args filenames : Ok
82: Check open filename arg using perf trace + vfs_getname : Ok
83: Zstd perf.data compression/decompression : Ok
$ make -C tools/perf build-test
make: Entering directory '/home/acme/git/perf/tools/perf'
- tarpkg: ./tests/perf-targz-src-pkg .
make_no_libpython_O: make NO_LIBPYTHON=1
make_no_sdt_O: make NO_SDT=1
make_tags_O: make tags
make_install_O: make install
make_install_bin_O: make install-bin
make_debug_O: make DEBUG=1
make_no_libdw_dwarf_unwind_O: make NO_LIBDW_DWARF_UNWIND=1
make_no_libelf_O: make NO_LIBELF=1
make_cscope_O: make cscope
make_no_backtrace_O: make NO_BACKTRACE=1
make_no_libnuma_O: make NO_LIBNUMA=1
make_no_ui_O: make NO_NEWT=1 NO_SLANG=1 NO_GTK2=1
make_no_newt_O: make NO_NEWT=1
make_with_babeltrace_O: make LIBBABELTRACE=1
make_util_pmu_bison_o_O: make util/pmu-bison.o
make_no_libunwind_O: make NO_LIBUNWIND=1
make_no_libbpf_DEBUG_O: make NO_LIBBPF=1 DEBUG=1
make_doc_O: make doc
make_perf_o_O: make perf.o
make_no_gtk2_O: make NO_GTK2=1
make_with_clangllvm_O: make LIBCLANGLLVM=1
make_clean_all_O: make clean all
make_no_demangle_O: make NO_DEMANGLE=1
make_with_gtk2_O: make GTK2=1
make_util_map_o_O: make util/map.o
make_pure_O: make
make_no_libbionic_O: make NO_LIBBIONIC=1
make_no_libaudit_O: make NO_LIBAUDIT=1
make_no_libbpf_O: make NO_LIBBPF=1
make_install_prefix_slash_O: make install prefix=/tmp/krava/
make_help_O: make help
make_no_syscall_tbl_O: make NO_SYSCALL_TABLE=1
make_no_scripts_O: make NO_LIBPYTHON=1 NO_LIBPERL=1
make_minimal_O: make NO_LIBPERL=1 NO_LIBPYTHON=1 NO_NEWT=1 NO_GTK2=1 NO_DEMANGLE=1 NO_LIBELF=1 NO_LIBUNWIND=1 NO_BACKTRACE=1 NO_LIBNUMA=1 NO_LIBAUDIT=1 NO_LIBBIONIC=1 NO_LIBDW_DWARF_UNWIND=1 NO_AUXTRACE=1 NO_LIBBPF=1 NO_LIBCRYPTO=1 NO_SDT=1 NO_JVMTI=1 NO_LIBZSTD=1 NO_LIBCAP=1 NO_SYSCALL_TABLE=1
make_no_libcrypto_O: make NO_LIBCRYPTO=1
make_static_O: make LDFLAGS=-static NO_PERF_READ_VDSO32=1 NO_PERF_READ_VDSOX32=1 NO_JVMTI=1
make_install_prefix_O: make install prefix=/tmp/krava
make_no_auxtrace_O: make NO_AUXTRACE=1
make_with_libpfm4_O: make LIBPFM4=1
make_no_libperl_O: make NO_LIBPERL=1
make_no_slang_O: make NO_SLANG=1
OK
make: Leaving directory '/home/acme/git/perf/tools/perf'
$
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYASljgAKCRCyPKLppCJ+
J/E/AQCOGFqF7UmEzuuTecWeeBNCwVyD3woHLU13ll/e5VLNggD/YD9t8CZS+vwy
21yL4/yXZloLFE48OCLRNWeq91FL/gs=
=uZDD
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-2021-01-17' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix 'CPU too large' error in Intel PT
- Correct event attribute sizes in 'perf inject'
- Sync build_bug.h and kvm.h kernel copies
- Fix bpf.h header include directive in 5sec.c 'perf trace' bpf example
- libbpf tests fixes
- Fix shadow stat 'perf test' for non-bash shells
- Take cgroups into account for shadow stats in 'perf stat'
* tag 'perf-tools-fixes-2021-01-17' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf inject: Correct event attribute sizes
perf intel-pt: Fix 'CPU too large' error
perf stat: Take cgroups into account for shadow stats
perf stat: Introduce struct runtime_stat_data
libperf tests: Fail when failing to get a tracepoint id
libperf tests: If a test fails return non-zero
libperf tests: Avoid uninitialized variable warning
perf test: Fix shadow stat test for non-bash shells
tools headers: Syncronize linux/build_bug.h with the kernel sources
tools headers UAPI: Sync kvm.h headers with the kernel sources
perf bpf examples: Fix bpf.h header include directive in 5sec.c example
One fix for a lack of alignment in our linker script, that can lead to crashes
depending on configuration etc.
One fix for the 32-bit VDSO after the C VDSO conversion.
Thanks to:
Andreas Schwab, Ariel Marcovitch, Christophe Leroy.
-----BEGIN PGP SIGNATURE-----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=jpfR
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a lack of alignment in our linker script, that can lead to
crashes depending on configuration etc.
One fix for the 32-bit VDSO after the C VDSO conversion.
Thanks to Andreas Schwab, Ariel Marcovitch, and Christophe Leroy"
* tag 'powerpc-5.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/vdso: Fix clock_gettime_fallback for vdso32
powerpc: Fix alignment bug within the init sections
Pull misc vfs fixes from Al Viro:
"Several assorted fixes.
I still think that audit ->d_name race is better fixed this way for
the benefit of backports, with any possibly fancier variants done on
top of it"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
dump_common_audit_data(): fix racy accesses to ->d_name
iov_iter: fix the uaccess area in copy_compat_iovec_from_user
umount(2): move the flag validity checks first
So technically there is nothing wrong with adding a pinned page to the
swap cache, but the pinning obviously means that the page can't actually
be free'd right now anyway, so it's a bit pointless.
However, the real problem is not with it being a bit pointless: the real
issue is that after we've added it to the swap cache, we'll try to unmap
the page. That will succeed, because the code in mm/rmap.c doesn't know
or care about pinned pages.
Even the unmapping isn't fatal per se, since the page will stay around
in memory due to the pinning, and we do hold the connection to it using
the swap cache. But when we then touch it next and take a page fault,
the logic in do_swap_page() will map it back into the process as a
possibly read-only page, and we'll then break the page association on
the next COW fault.
Honestly, this issue could have been fixed in any of those other places:
(a) we could refuse to unmap a pinned page (which makes conceptual
sense), or (b) we could make sure to re-map a pinned page writably in
do_swap_page(), or (c) we could just make do_wp_page() not COW the
pinned page (which was what we historically did before that "mm:
do_wp_page() simplification" commit).
But while all of them are equally valid models for breaking this chain,
not putting pinned pages into the swap cache in the first place is the
simplest one by far.
It's also the safest one: the reason why do_wp_page() was changed in the
first place was that getting the "can I re-use this page" wrong is so
fraught with errors. If you do it wrong, you end up with an incorrectly
shared page.
As a result, using "page_maybe_dma_pinned()" in either do_wp_page() or
do_swap_page() would be a serious bug since it is only a (very good)
heuristic. Re-using the page requires a hard black-and-white rule with
no room for ambiguity.
In contrast, saying "this page is very likely dma pinned, so let's not
add it to the swap cache and try to unmap it" is an obviously safe thing
to do, and if the heuristic might very rarely be a false positive, no
harm is done.
Fixes: 09854ba94c ("mm: do_wp_page() simplification")
Reported-and-tested-by: Martin Raiber <martin@urbackup.org>
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With commit 4df4cb9e99, the Hyper-V direct-mode STIMER is actually
initialized before LAPIC is initialized: see
apic_intr_mode_init()
x86_platform.apic_post_init()
hyperv_init()
hv_stimer_alloc()
apic_bsp_setup()
setup_local_APIC()
setup_local_APIC() temporarily disables LAPIC, initializes it and
re-eanble it. The direct-mode STIMER depends on LAPIC, and when it's
registered, it can be programmed immediately and the timer can fire
very soon:
hv_stimer_init
clockevents_config_and_register
clockevents_register_device
tick_check_new_device
tick_setup_device
tick_setup_periodic(), tick_setup_oneshot()
clockevents_program_event
When the timer fires in the hypervisor, if the LAPIC is in the
disabled state, new versions of Hyper-V ignore the event and don't inject
the timer interrupt into the VM, and hence the VM hangs when it boots.
Note: when the VM starts/reboots, the LAPIC is pre-enabled by the
firmware, so the window of LAPIC being temporarily disabled is pretty
small, and the issue can only happen once out of 100~200 reboots for
a 40-vCPU VM on one dev host, and on another host the issue doesn't
reproduce after 2000 reboots.
The issue is more noticeable for kdump/kexec, because the LAPIC is
disabled by the first kernel, and stays disabled until the kdump/kexec
kernel enables it. This is especially an issue to a Generation-2 VM
(for which Hyper-V doesn't emulate the PIT timer) when CONFIG_HZ=1000
(rather than CONFIG_HZ=250) is used.
Fix the issue by moving hv_stimer_alloc() to a later place where the
LAPIC timer is initialized.
Fixes: 4df4cb9e99 ("x86/hyperv: Initialize clockevents earlier in CPU onlining")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20210116223136.13892-1-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
The change of ia64's default memory model to SPARSEMEM causes defconfig
build to fail:
CC kernel/async.o
In file included from include/linux/numa.h:25,
from include/linux/async.h:13,
from kernel/async.c:47:
arch/ia64/include/asm/sparsemem.h:14:40: warning: "PAGE_SHIFT" is not defined, evaluates to 0 [-Wundef]
14 | #if ((CONFIG_FORCE_MAX_ZONEORDER - 1 + PAGE_SHIFT) > SECTION_SIZE_BITS)
| ^~~~~~~~~~
In file included from include/linux/gfp.h:6,
from include/linux/xarray.h:14,
from include/linux/radix-tree.h:19,
from include/linux/idr.h:15,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/energy_model.h:7,
from include/linux/device.h:16,
from include/linux/async.h:14,
from kernel/async.c:47:
include/linux/mmzone.h:1156:2: error: #error Allocator MAX_ORDER exceeds SECTION_SIZE
1156 | #error Allocator MAX_ORDER exceeds SECTION_SIZE
| ^~~~~
The error cause is the missing definition of PAGE_SHIFT in the calculation
of SECTION_SIZE_BITS.
Add include of <asm/page.h> to arch/ia64/include/asm/sparsemem.h to solve
the problem.
Fixes: 214496cb18 ("ia64: make SPARSEMEM default and disable DISCONTIGMEM")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. No reason to add one to it.
Fixes: 886f6f8337 ("i2c: octeon: Support I2C_M_RECV_LEN")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
VI I2C controller has known hardware bug where immediate multiple
writes to TX_FIFO register gets stuck.
Recommended software work around is to read I2C register after
each write to TX_FIFO register to flush out the data.
This patch implements this work around for VI I2C controller.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In order to not to start returning errors when new I2C_M flags are
added, change behavior to just ignore all flags that we don't know
about. This includes the I2C_M_DMA_SAFE flag that already exists but
causes -EINVAL to be returned for valid transactions.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If there are no requests at the time __io_uring_task_cancel() is called,
tctx_inflight() returns zero and and it terminates not getting a chance
to go through __io_uring_files_cancel() and do
io_disable_sqo_submit(). And we absolutely want them disabled by the
time cancellation ends.
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Fixes: d9d05217cb ("io_uring: stop SQPOLL submit on creator's death")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 3226b158e6 ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
Since v1 [0]:
- fix "Fixes:" tag;
- refine commit message (mention copybreak usecase).
[0] https://lore.kernel.org/netdev/20210114235423.232737-1-alobakin@pm.me
Fixes: a1c7fff7e1 ("net: netdev_alloc_skb() use build_skb()")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Link: https://lore.kernel.org/r/20210115150354.85967-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nine minor fixes, 7 in drivers and 2 in the core SCSI disk driver (sd)
which should be harmless involving removing an unused variable and
quietening a spurious warning.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYANKJiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVSyAP9a4xdK
9A4seh2/LW3GwPsoQUJQINe4yok/lGVXSQk3XQD/QkkYbzeqVGN4BHK1LQX2R9Sw
wy+E4ENjdOY+9p+KMxo=
=m0jh
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine minor fixes, seven in drivers and two in the core SCSI disk
driver (sd) which should be harmless involving removing an unused
variable and quietening a spurious warning"
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Remove obsolete variable in sd_remove()
scsi: sd: Suppress spurious errors when WRITE SAME is being disabled
scsi: scsi_debug: Fix memleak in scsi_debug_init()
scsi: mpt3sas: Fix spelling mistake in Kconfig "compatiblity" -> "compatibility"
scsi: qedi: Correct max length of CHAP secret
scsi: ufs: Correct the LUN used in eh_device_reset_handler() callback
scsi: ufs: Relocate flush of exceptional event
scsi: ufs: Relax the condition of UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL
scsi: ufs: Fix possible power drain during system suspend
We are not guaranteed the locking environment that would prevent
dentry getting renamed right under us. And it's possible for
old long name to be freed after rename, leading to UAF here.
Cc: stable@kernel.org # v2.6.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----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=CYyj
-----END PGP SIGNATURE-----
Merge tag 'block-5.11-2021-01-16' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Just an nvme pull request via Christoph:
- don't initialize hwmon for discover controllers (Sagi Grimberg)
- fix iov_iter handling in nvme-tcp (Sagi Grimberg)
- fix a preempt warning in nvme-tcp (Sagi Grimberg)
- fix a possible NULL pointer dereference in nvme (Israel Rukshin)"
* tag 'block-5.11-2021-01-16' of git://git.kernel.dk/linux-block:
nvme: don't intialize hwmon for discovery controllers
nvme-tcp: fix possible data corruption with bio merges
nvme-tcp: Fix warning with CONFIG_DEBUG_PREEMPT
nvmet-rdma: Fix NULL deref when setting pi_enable and traddr INADDR_ANY
WARNING: CPU: 1 PID: 11100 at fs/io_uring.c:9096
io_uring_flush+0x326/0x3a0 fs/io_uring.c:9096
RIP: 0010:io_uring_flush+0x326/0x3a0 fs/io_uring.c:9096
Call Trace:
filp_close+0xb4/0x170 fs/open.c:1280
close_files fs/file.c:401 [inline]
put_files_struct fs/file.c:416 [inline]
put_files_struct+0x1cc/0x350 fs/file.c:413
exit_files+0x7e/0xa0 fs/file.c:433
do_exit+0xc22/0x2ae0 kernel/exit.c:820
do_group_exit+0x125/0x310 kernel/exit.c:922
get_signal+0x3e9/0x20a0 kernel/signal.c:2770
arch_do_signal_or_restart+0x2a8/0x1eb0 arch/x86/kernel/signal.c:811
handle_signal_work kernel/entry/common.c:147 [inline]
exit_to_user_mode_loop kernel/entry/common.c:171 [inline]
exit_to_user_mode_prepare+0x148/0x250 kernel/entry/common.c:201
__syscall_exit_to_user_mode_work kernel/entry/common.c:291 [inline]
syscall_exit_to_user_mode+0x19/0x50 kernel/entry/common.c:302
entry_SYSCALL_64_after_hwframe+0x44/0xa9
An SQPOLL ring creator task may have gotten rid of its file note during
exit and called io_disable_sqo_submit(), but the io_uring is still left
referenced through fdtable, which will be put during close_files() and
cause a false positive warning.
First split the warning into two for more clarity when is hit, and the
add sqo_dead check to handle the described case.
Reported-by: syzbot+a32b546d58dde07875a1@syzkaller.appspotmail.com
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
WARNING: CPU: 1 PID: 9094 at fs/io_uring.c:8884
io_disable_sqo_submit+0x106/0x130 fs/io_uring.c:8884
Call Trace:
io_uring_flush+0x28b/0x3a0 fs/io_uring.c:9099
filp_close+0xb4/0x170 fs/open.c:1280
close_fd+0x5c/0x80 fs/file.c:626
__do_sys_close fs/open.c:1299 [inline]
__se_sys_close fs/open.c:1297 [inline]
__x64_sys_close+0x2f/0xa0 fs/open.c:1297
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
io_uring's final close() may be triggered by any task not only the
creator. It's well handled by io_uring_flush() including SQPOLL case,
though a warning in io_disable_sqo_submit() will fallaciously fire by
moving this warning out to the only call site that matters.
Reported-by: syzbot+2f5d1785dc624932da78@syzkaller.appspotmail.com
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we're freeing/finishing iopoll requests, ensure we check if the task
is in idling in terms of cancelation. Otherwise we could end up waiting
forever in __io_uring_task_cancel() if the task has active iopoll
requests that need cancelation.
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=XL14
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.11-2021-01-16' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"We still have a pending fix for a cancelation issue, but it's still
being investigated. In the meantime:
- Dead mm handling fix (Pavel)
- SQPOLL setup error handling (Pavel)
- Flush timeout sequence fix (Marcelo)
- Missing finish_wait() for one exit case"
* tag 'io_uring-5.11-2021-01-16' of git://git.kernel.dk/linux-block:
io_uring: ensure finish_wait() is always called in __io_uring_task_cancel()
io_uring: flush timeouts that should already have expired
io_uring: do sqo disable on install_fd error
io_uring: fix null-deref in io_disable_sqo_submit
io_uring: don't take files/mm for a dead task
io_uring: drop mm and files after task_work_run
There are a few more fixes than a normal rc4, largely due to the bubble
introduced by the holiday break:
* A fix to return -ENOSYS for syscall number -1, which previously
returned an uninitialized value.
* A fix to time_init() to ensure of_clk_init() has been called, without
which clock drivers may not be initialized.
* A fix to the sifive,uart0 driver to properly display the baud rate. A
fix to initialize MPIE that allows interrupts to be processed during
system calls.
* A fix to avoid erronously begin tracing IRQs when interrupts are
disabled, which at least triggers suprious lockdep failures.
* A workaround for a warning related to calling smp_processor_id() while
preemptible. The warning itself is suprious on currently availiable
systems.
* A fix to properly include the generic time VDSO calls. A fix to our
kasan address mapping. A fix to the HiFive Unleashed device tree,
which allows the Ethernet PHY to be properly initialized by Linux (as
opposed to relying on the bootloader).
* A defconfig update to include SiFive's GPIO driver, which is present
on the HiFive Unleashed and necessary to initialize the PHY.
* A fix to avoid allocating memory while initializing reserved memory.
* A fix to avoid allocating the last 4K of memory, as pointers there
alias with syscall errors.
There are also two cleanups that should have no functional effect but do
fix build warnings:
* A cleanup to drop a duplicated definition of PAGE_KERNEL_EXEC.
* A cleanup to properly declare the asm register SP shim.
* A cleanup to the rv32 memory size Kconfig entry, to reflect the actual
size of memory availiable.
-----BEGIN PGP SIGNATURE-----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=guLu
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"There are a few more fixes than a normal rc4, largely due to the
bubble introduced by the holiday break:
- return -ENOSYS for syscall number -1, which previously returned an
uninitialized value.
- ensure of_clk_init() has been called in time_init(), without which
clock drivers may not be initialized.
- fix sifive,uart0 driver to properly display the baud rate. A fix to
initialize MPIE that allows interrupts to be processed during
system calls.
- avoid erronously begin tracing IRQs when interrupts are disabled,
which at least triggers suprious lockdep failures.
- workaround for a warning related to calling smp_processor_id()
while preemptible. The warning itself is suprious on currently
availiable systems.
- properly include the generic time VDSO calls. A fix to our kasan
address mapping. A fix to the HiFive Unleashed device tree, which
allows the Ethernet PHY to be properly initialized by Linux (as
opposed to relying on the bootloader).
- defconfig update to include SiFive's GPIO driver, which is present
on the HiFive Unleashed and necessary to initialize the PHY.
- avoid allocating memory while initializing reserved memory.
- avoid allocating the last 4K of memory, as pointers there alias
with syscall errors.
There are also two cleanups that should have no functional effect but
do fix build warnings:
- drop a duplicated definition of PAGE_KERNEL_EXEC.
- properly declare the asm register SP shim.
- cleanup the rv32 memory size Kconfig entry, to reflect the actual
size of memory availiable"
* tag 'riscv-for-linus-5.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Fix maximum allowed phsyical memory for RV32
RISC-V: Set current memblock limit
RISC-V: Do not allocate memblock while iterating reserved memblocks
riscv: stacktrace: Move register keyword to beginning of declaration
riscv: defconfig: enable gpio support for HiFive Unleashed
dts: phy: add GPIO number and active state used for phy reset
dts: phy: fix missing mdio device and probe failure of vsc8541-01 device
riscv: Fix KASAN memory mapping.
riscv: Fixup CONFIG_GENERIC_TIME_VSYSCALL
riscv: cacheinfo: Fix using smp_processor_id() in preemptible
riscv: Trace irq on only interrupt is enabled
riscv: Drop a duplicated PAGE_KERNEL_EXEC
riscv: Enable interrupts during syscalls with M-Mode
riscv: Fix sifive serial driver
riscv: Fix kernel time_init()
riscv: return -ENOSYS for syscall -1
Turning a pinned page read-only breaks the pinning after COW. Don't do it.
The whole "track page soft dirty" state doesn't work with pinned pages
anyway, since the page might be dirtied by the pinning entity without
ever being noticed in the page tables.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Turning page table entries read-only requires the mmap_sem held for
writing.
So stop doing the odd games with turning things from read locks to write
locks and back. Just get the write lock.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux kernel can only map 1GB of address space for RV32 as the page offset
is set to 0xC0000000. The current description in the Kconfig is confusing
as it indicates that RV32 can support 2GB of physical memory. That is
simply not true for current kernel. In future, a 2GB split support can be
added to allow 2GB physical address space.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Currently, linux kernel can not use last 4k bytes of addressable space
because IS_ERR_VALUE macro treats those as an error. This will be an issue
for RV32 as any memblock allocator potentially allocate chunk of memory
from the end of DRAM (2GB) leading bad address error even though the
address was technically valid.
Fix this issue by limiting the memblock if available memory spans the
entire address space.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
sizeof needs to be called on the compat pointer, not the native one.
Fixes: 89cd35c58b ("iov_iter: transparently handle compat iovecs in import_iovec")
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- Select missing Kconfig dependencies for DM integrity and zoned
targets.
- 4 fixes for DM crypt target's support to optionally bypass
kcryptd workqueues.
- Fix DM snapshot merge supports missing data flushes before
committing metadata.
- Fix DM integrity data device flushing when external metadata is
used.
- Fix DM integrity's maximum number of supported constructor arguments
that user can request when creating an integrity device.
- Eliminate DM core ioctl logging noise when an ioctl is issued
without required CAP_SYS_RAWIO permission.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEJfWUX4UqZ4x1O2wixSPxCi2dA1oFAmACJwsTHHNuaXR6ZXJA
cmVkaGF0LmNvbQAKCRDFI/EKLZ0DWr93B/sFpKbCjRxZhGdOz8u2UIV9jGoSzAaZ
3qdSTruCp1HMTsz0J/+bFBTMQKKap+8u8kzhCOLAqtZgEz13P0D3NyDUGiCxj07O
vPZJQ3COrClknq5byKws/aOKcnbr25odk6Zq+gFmk47pdNFBMkzNMf0IbdVJsj19
d0tnTRkIiycC8hnXOr/tHufnmERrw9nZpq3cLEHT6vaXc4FxcYXbo4UEMIwKjgcB
AnsRrqpqKyayG+G/SEs01JM9eYznWRPqf3L03wTWfieAsFjDoIp/ek8iXWjEwLtZ
BnhxFwodWvycFb9ITaxlFgfyiBSgU1f3tsIYjU4MHCSFI6u5b83y57Dl
=FnV7
-----END PGP SIGNATURE-----
Merge tag 'for-5.11/dm-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM-raid's raid1 discard limits so discards work.
- Select missing Kconfig dependencies for DM integrity and zoned
targets.
- Four fixes for DM crypt target's support to optionally bypass kcryptd
workqueues.
- Fix DM snapshot merge supports missing data flushes before committing
metadata.
- Fix DM integrity data device flushing when external metadata is used.
- Fix DM integrity's maximum number of supported constructor arguments
that user can request when creating an integrity device.
- Eliminate DM core ioctl logging noise when an ioctl is issued without
required CAP_SYS_RAWIO permission.
* tag 'for-5.11/dm-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm crypt: defer decryption to a tasklet if interrupts disabled
dm integrity: fix the maximum number of arguments
dm crypt: do not call bio_endio() from the dm-crypt tasklet
dm integrity: fix flush with external metadata device
dm: eliminate potential source of excessive kernel log noise
dm snapshot: flush merged data before committing metadata
dm crypt: use GFP_ATOMIC when allocating crypto requests from softirq
dm crypt: do not wait for backlogged crypto request completion in softirq
dm zoned: select CONFIG_CRC32
dm integrity: select CRYPTO_SKCIPHER
dm raid: fix discard limits for raid1
LinuxSourceTree will unceremoniously crash if the user doesn't call
read_kunitconfig() first in a number of functions.
And currently every place we create an instance, the caller also calls
create_kunitconfig() and read_kunitconfig().
Move these instead into __init__() so they can't be forgotten and to
reduce copy-paste.
The https://github.com/google/pytype type-checker complained that
_config wasn't initialized. With this, kunit_tool now type checks
under both pytype and mypy.
Add an optional boolean that can be used to disable this for use cases
in the future where we might not need/want to load the config.
Signed-off-by: Daniel Latypov <dlatypov@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The code to handle aggregating statuses didn't check that the status
actually got set to some non-None value.
Default the value to SUCCESS instead of adding a bunch of `is None`
checks.
This sorta follows the precedent in commit 3fc48259d5 ("kunit: Don't
fail test suites if one of them is empty").
Also slightly simplify the code and add type annotations.
Signed-off-by: Daniel Latypov <dlatypov@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The authors of this tool were more familiar with a different
type-checker, https://github.com/google/pytype.
That's open source, but mypy seems more prevalent (and runs faster).
And unlike pytype, mypy doesn't try to infer types so it doesn't check
unanotated functions.
So annotate ~all functions in kunit tool to increase type-checking
coverage.
Note: per https://www.python.org/dev/peps/pep-0484/, `__init__()` should
be annotated as `-> None`.
Doing so makes mypy discover a number of new violations.
Exclude main() since we reuse `request` for the different types of
requests, which mypy isn't happy about.
This commit fixes all but one error, where `TestSuite.status` might be
None.
Signed-off-by: Daniel Latypov <dlatypov@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit fadb08e7c7 ("kunit: Support for Parameterized Testing")
introduced support but lacks documentation for how to use it.
This patch builds on commit 1f0e943df6 ("Documentation: kunit: provide
guidance for testing many inputs") to show a minimal example of the new
feature.
Signed-off-by: Daniel Latypov <dlatypov@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Various helper functions were misspelling "diagnostic" in their names.
It finally got annoying, so fix it.
Signed-off-by: David Gow <davidgow@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Daniel Borkmann says:
====================
pull-request: bpf 2021-01-16
1) Fix a double bpf_prog_put() for BPF_PROG_{TYPE_EXT,TYPE_TRACING} types in
link creation's error path causing a refcount underflow, from Jiri Olsa.
2) Fix BTF validation errors for the case where kernel modules don't declare
any new types and end up with an empty BTF, from Andrii Nakryiko.
3) Fix BPF local storage helpers to first check their {task,inode} owners for
being NULL before access, from KP Singh.
4) Fix a memory leak in BPF setsockopt handling for the case where optlen is
zero and thus temporary optval buffer should be freed, from Stanislav Fomichev.
5) Fix a syzbot memory allocation splat in BPF_PROG_TEST_RUN infra for
raw_tracepoint caused by too big ctx_size_in, from Song Liu.
6) Fix LLVM code generation issues with verifier where PTR_TO_MEM{,_OR_NULL}
registers were spilled to stack but not recognized, from Gilad Reti.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
MAINTAINERS: Update my email address
selftests/bpf: Add verifier test for PTR_TO_MEM spill
bpf: Support PTR_TO_MEM{,_OR_NULL} register spilling
bpf: Reject too big ctx_size_in for raw_tp test run
libbpf: Allow loading empty BTFs
bpf: Allow empty module BTFs
bpf: Don't leak memory in bpf getsockopt when optlen == 0
bpf: Update local storage test to check handling of null ptrs
bpf: Fix typo in bpf_inode_storage.c
bpf: Local storage helpers should check nullness of owner ptr passed
bpf: Prevent double bpf_prog_put call from bpf_tracing_prog_attach
====================
Link: https://lore.kernel.org/r/20210116002025.15706-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fl_set_enc_opt() simply checks if there are still bytes left to parse,
but this is not sufficent as syzbot seems to be able to generate
malformatted netlink messages. nla_ok() is more strict so should be
used to validate the next nlattr here.
And nla_validate_nested_deprecated() has less strict check too, it is
probably too late to switch to the strict version, but we can just
call nla_ok() too after it.
Reported-and-tested-by: syzbot+2624e3778b18fc497c92@syzkaller.appspotmail.com
Fixes: 0a6e77784f ("net/sched: allow flower to match tunnel options")
Fixes: 79b1011cb3 ("net: sched: allow flower to match erspan options")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20210115185024.72298-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge misc fixes from Andrew Morton:
"10 patches.
Subsystems affected by this patch series: MAINTAINERS and mm (slub,
pagealloc, memcg, kasan, vmalloc, migration, hugetlb, memory-failure,
and process_vm_access)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/process_vm_access.c: include compat.h
mm,hwpoison: fix printing of page flags
MAINTAINERS: add Vlastimil as slab allocators maintainer
mm/hugetlb: fix potential missing huge page size info
mm: migrate: initialize err in do_migrate_pages
mm/vmalloc.c: fix potential memory leak
arm/kasan: fix the array size of kasan_early_shadow_pte[]
mm/memcontrol: fix warning in mem_cgroup_page_lruvec()
mm/page_alloc: add a missing mm_page_alloc_zone_locked() tracepoint
mm, slub: consider rest of partial list if acquire_slab() fails
Several bug fixes.
- Fix a ucma memory leak introduced in v5.9 while fixing the Syzkaller
bugs
- Don't fail when the xarray wraps for user verbs objects
- User triggerable oops regression from the umem page size rework
- Error unwind bugs in usnic, ocrdma, mlx5 and cma
-----BEGIN PGP SIGNATURE-----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=8eDD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A fairly modest set of bug fixes, nothing abnormal from the merge
window
The ucma patch is a bit on the larger side, but given the regression
was recently added I've opted to forward it to the rc stream.
- Fix a ucma memory leak introduced in v5.9 while fixing the
Syzkaller bugs
- Don't fail when the xarray wraps for user verbs objects
- User triggerable oops regression from the umem page size rework
- Error unwind bugs in usnic, ocrdma, mlx5 and cma"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/cma: Fix error flow in default_roce_mode_store
RDMA/mlx5: Fix wrong free of blue flame register on error
IB/mlx5: Fix error unwinding when set_has_smi_cap fails
RDMA/umem: Avoid undefined behavior of rounddown_pow_of_two()
RDMA/ocrdma: Fix use after free in ocrdma_dealloc_ucontext_pd()
RDMA/usnic: Fix memleak in find_free_vf_and_create_qp_grp
RDMA/restrack: Don't treat as an error allocation ID wrapping
RDMA/ucma: Do not miss ctx destruction steps in some cases
If we enter with requests pending and performm cancelations, we'll have
a different inflight count before and after calling prepare_to_wait().
This causes the loop to restart. If we actually ended up canceling
everything, or everything completed in-between, then we'll break out
of the loop without calling finish_wait() on the waitqueue. This can
trigger a warning on exit_signals(), as we leave the task state in
TASK_UNINTERRUPTIBLE.
Put a finish_wait() after the loop to catch that case.
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Kent Gibson