- Support to add/delete/store/restore 64 and 128 Ethernet addresses for Xframe I and Xframe II respectively.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring secondary unicast addresses. Unicast
addresses take precendece over multicast addresses when filling
the exact address filters to avoid going to promiscous mode.
When more unicast addresses are present than filter slots,
unicast filtering is disabled and all slots can be used for
multicast addresses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions for reg_pattern_test and reg_set_and check
Changed macros to use these functions
Compiled x86, untested
Size decreased ~2K
old:
$ size drivers/net/e1000e/ethtool.o
text data bss dec hex filename
14461 0 0 14461 387d drivers/net/e1000e/ethtool.o
new:
$ size drivers/net/e1000e/ethtool.o
text data bss dec hex filename
12498 0 0 12498 30d2 drivers/net/e1000e/ethtool.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minimal macro to function conversion in e1000_ethtool.c
Adds functions reg_pattern_test and reg_set_and_check
Changes REG_PATTERN_TEST and REG_SET_AND_CHECK macros
to call these functions.
Saves ~2.5KB
Compiled x86, untested (no hardware)
old:
$ size drivers/net/e1000/e1000_ethtool.o
text data bss dec hex filename
16778 0 0 16778 418a drivers/net/e1000/e1000_ethtool.o
new:
$ size drivers/net/e1000/e1000_ethtool.o
text data bss dec hex filename
14128 0 0 14128 3730 drivers/net/e1000/e1000_ethtool.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the RDC R6040 MAC we can find in the RDC
R-321x System-on-chips.
Signed-off-by: Sten Wang <sten.wang@rdc.com.tw>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
On the systems that have cache incoherent DMA, including ARM, there
is a race condition between software allocating a new receive buffer
and hardware writing into a buffer. The two race on touching the last
Receive Frame Descriptor (RFD). It has its el-bit set and its next
link equal to 0. When hardware encounters this buffer it attempts to
write data to it and then update Status Word bits and Actual Count in
the RFD. At the same time software may try to clear the el-bit and
set the link address to a new buffer.
Since the entire RFD is once cache-line, the two write operations can
collide. This can lead to the receive unit stalling or interpreting
random memory as its receive area.
The fix is to set the el-bit on and the size to 0 on the next to last
buffer in the chain. When the hardware encounters this buffer it stops
and does not write to it at all. The hardware issues an RNR interrupt
with the receive unit in the No Resources state. Software can write
to the tail of the list because it knows hardware will stop on the
previous descriptor that was marked as the end of list.
Once it has a new next to last buffer prepared, it can clear the el-bit
and set the size on the previous one. The race on this buffer is safe
since the link already points to a valid next buffer and the software
can handle the race setting the size (assuming aligned 16 bit writes
are atomic with respect to the DMA read). If the hardware sees the
el-bit cleared without the size set, it will move on to the next buffer
and skip this one. If it sees the size set but the el-bit still set,
it will complete that buffer and then RNR interrupt and wait.
Signed-off-by: David Acker <dacker@roinet.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To quote one of my favorite contemporary author:
[include/linux/sockios.h]
* THESE IOCTLS ARE _DEPRECATED_ AND WILL DISAPPEAR IN 2.5.X -DaveM
*/
#define SIOCDEVPRIVATE 0x89F0 /* to 89FF */
[...]
Gentoo's snmpd trips up over this code when trying to figure if the driver
supports the non-SIOCDEVPRIVATE API or not. One can argue over its choice
of heuristic but there no reason to make ioctl more ugly than needed.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Huang <jesse@icplus.com.tw>
Tested-by: Volker Sauer <vsauer@dvs.tu-darmstadt.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following cleanups:
- static functions in .c files shouldn't be marked inline
- make needlessly global code static
- #if 0 unused code
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While cleaning up the internal API focussing on Fiber and CX4 code
we found that I had broken the copper PHY initialization code. This
patch restores the PHY-specific code. This is mostly uninteresting
since no copper PHY boards are yet available. The changes have been
tested against Fiber only as I do not even have copper PHY versions
of 82598 macs.
This change actually cleans up the API code a bit more and we
lose some initialization code. A few PHY link detection helper
lines of code have been snuck into this patch, as well as a
read flush where it was suspected that this might cause issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
e1000e will from now on support the PCI-Express adapters that
previously were supported by e1000. This support means better
performance and easier debugging from now on for both the old
PCI-X/PCI hardware and PCI-Express adapters.
This patch also moves 3 recently merged device IDs over to e1000e
that are identical to quad-port versions of already existing
dual port versions. With this last bit every former e1000 pci-e
device should work now with e1000e.
Here is a brief list of which gigabit driver to use with which
adapter:
e1000:
82540 -> 82547
e1000e:
82571 -> 82573
ich8, ich9 (82562 or 82566)
es2lan (80003eslan)
igb: (not yet merged, only available from e1000.sf.net)
82575
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
L1 ASPM link (pci-e link power savings) has significant benefits
(~1W savings when link is active) but unfortunately does not work
correctly on any of the chipsets that have 82573 on mobile platforms
which causes various nuisances:
- eeprom reads return garbage information leading to bad eeprom
checksums
- long ping times (up to 2 seconds)
- complete system hangs (freeze/lockup)
A lot of T60 owners have been plagued by this, but other mobile
solutions also suffer from these symptoms.
Disabling L1 ASPM before we activate the PCI-E link fixes all of
these issues at the cost of some power consumption.
Remove a workaround RDTR adjustment that is no longer needed with
this new one.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Port alternate MAC address support from the sourceforge
e1000 driver to the upstream e1000e driver.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* use irq_handler_t where appropriate
* no need to use 'irq' function arg, its already stored in a data struct
* rename irq handler 'irq' argument to 'dummy', where the function
has been analyzed and proven not to use its first argument.
* remove always-false "dev_id == NULL" test from irq handlers
* remove pointless casts from void*
* declance: irq argument is not const
* add KERN_xxx printk prefix
* fix minor whitespace weirdness
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This converts uses of ARRAY_SIZE(), and while at it also kills
unreachable code as far as I can say. I can't tell what was the author
trying to do with the following check. First we have:
PNMI_STATIC const SK_PNMI_STATADDR
StatAddr[SK_PNMI_MAX_IDX][SK_PNMI_MAC_TYPES];
and then a check goes like this:
if (SK_PNMI_MAX_IDX !=
(sizeof(StatAddr) / (sizeof(SK_PNMI_STATADDR) * SK_PNMI_MAC_TYPES)))
with the second line being just ARRAY_SIZE(StatAddr), which will always
return SK_PNMI_MAX_IDX, rendering the check useless.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using ARRAY_SIZE() on arrays of the form array[][K] makes it unnecessary
to know the value of K when checking its size.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move wlan_postpone_association_work() and wlan_cancel_association_work()
from a assoc.h file to the sole user, into wext.c.
Renamed those two functions to to libertas_XXX as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable interrupts in the iwl4965 before calling request_irq() for
the case that the previous OS or the BIOS left a pending interrupt in
the chip. This behavior has been observed on some laptops such as T61
Thinkpads and Toshiba Portege R500
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there are 2 linked structures, using a temporary variable to hold a pointer
to the often used structure usually produces better code (smaller and faster)
since compiler does not have to constantly re-fetch data from the first structure.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bring scan result handling more in line with drivers like ipw. Scan
results are aggregated and a BSS dropped after 15 seconds if no beacon
is received. This allows the driver to interact better with userspace
where more than one process may request scans or results at any time.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a consistent naming scheme for the ops.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the limits provided by mac80211.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put all access to wl->current_dev under protection of the mutex.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need the set_key callback, as we don't do hw crypto.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement much easier and more lightweight locking for
the periodic work. This also removes the last big busywait
loop and replaces it by a sleeping loop.
This patch for b43legacy is patterned aftar the same patch
for b43 by Michael Buesch <mb@bu3sch.de>.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the direct call to rfkill on an rfkill event
and replaces it with an input device. This way userspace is also
notified about the event.
This patch is the port to b43legacy of a patch for b43 by Michael Buesch
<mb@bu3sch.de>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds full support for the RFKILL button and the RFKILL LED trigger.
This is a port to b43legacy of a patch by Michael Buesch <mb@bu3sch.de>
for b43.
Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drive the LEDs through the generic LED triggers.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to b43legacy.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the iwl3945 & iwl4965 drivers share some common Kconfig
symbols. This split it up into options for the individual drivers
and gets rid of all the CONFIG_IWLWIFI cruft.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwl3945 and iwl4965 devices share some common structure, but with a
lot of difference split all over. Currently the two drivers share a lot
of headers and use ugly preprocessor magic to manage the difference.
This patch keeps two entirely separate copies of the headers to get rid
of these hacks an ease future development.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mark more functions/variables static
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch do the following 2 things:
1. Make sure we don't add rate 60M part of supported rate in proble request,
some AP does not like that.
2. It is wrong to set priv->active_rate in this function, this will set
it to all avialable rates which might overwrite the mode supported rate.
priv->active_rate should be set by only from iwl_set_rate.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patche shortens the name of struct fw_image_desc to be struct
fw_desc.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds SCD registers for 5965
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves 3945 SCD registers to iwl-prph.h. These registers
are assigned from the periphery bus
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves 4965 SCD registers to iwl-prph.h. These registers
are assigned from the periphery bus
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces wording 'restricted' with more appropriate 'nic access'
NIC access is grabbed to prevent NIC entering power save mode
General cleanup of iwl-io.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames restricted_mem suffix with more proper
name targ_mem for function accessing memory on the nic in target mode
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames restricted_reg suffix with more proper
name prhp for function accessing registers on the periphery bus.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver drops any Rx frame larger than 2332 bytes, but with A-MSDU
frame, it could be up to 4K. This patch makes sure we can process larger
A-MSDU frame.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI_DEVICE macro is more concise when using defualt values
in device definitions
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cck_power_index_compensation variable was never used
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These pieces of code appear to be useless. The BUG_ON is also performed in
iwl_send_cmd_async.
Serious karma would be needed to enter iwl_ativate_qos with a null priv.
I had a deja vu when patching this, but for the life of me I couldn't track
down a similar patch.
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving code around, lindent, and whatnot created several places where
there appeared to be an 75 column "rule" instead of 80. This patch removes
those that I can spot, hopefully increasing readability.
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch shorten two comments lines in iwl-3945.c
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch remove cck_flag from iwl_driver_hw_info, this flag
is unused after spliting the iwl-base.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds TGN flag to QoS parameters. This flag governs enablement of
NAV shortening with CF-End and filters in 4 or 8K RX AMSDU packets
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up style of 'return' of rate scale 4965 functions.
It renames return name variables rc to ret, change functions to void if no
meaningful value was returned it add return of -EINVAL for checks of wrong
arguments.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames queue pointers to write_ptr and read_ptr
instead of first_empty and last_used. This is closer to technical
terminology we everyday use
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct the spelling of aqcuire.
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing various spelling errors and typos. Mostly in comments. In total
27 words were corrected, some of which occurred more than ones.
Signed-Of-By: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds erp_ie_changed handler to iwl4956
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Version bump.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag to struct txdata_entry_desc that specifies whether an ack for the
frame is to be expected. Use this flag to set the ACK bit in the tx descriptor.
Previously, the ACK bit could be set incorrectly on CTS-to-self frames, so they
caused retries and were reported to be failed in the txdone handlers.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a buffer, csr_cache which is used to hold copies of data being passed
to the USB stack which can get corrupted if multiple threads attempt to access
CSR registers simultaneously. There is also the possibility if multiple
threads try to access BBP or RF registers for the multiple USB operations
needed to get interleaved leading to incorrect results. This patch introduces
a mutex to prevent such simultaneous access. The interleaved access problem
may also affect the PCI devices but if so that will be handled in a follow-up
patch.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverty indicated that data_desc with a single
element array is bad coding style. This removes
the structure and forces everybody to use __le32.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes rt73 antenna selection to what I believe is the correct way.
It also fixes a small selection bug that switched the antennas by accident.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the updated antenna setup the following
variables are no longer used.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes rt61 antenna selection again. It helps at least with the
rt61 pci card in my box, I hope I haven't broken behaviour on other RF chips.
RF 2529 antenna setup is incomplete, we need to at code for diversity when we
figure out how it is done properly.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some register accesses need rt2x00dev to be non-const
they all need modifying so the prototype is consistent.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering rfkill, make sure a initial
poll event is directly executed to detect the initial
rfkill state and send the event to the rfkill layer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
input-polldev requires a correctly allocated
and initialized input device to be set for the
input_polled_dev->input field.
Failure to do that will prevent correct polling
of the device.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on investigation of the legacy drivers, I have made the
following assumptions of the antenna setup:
- R77 is the TX antenna configuration
- RF2529 fetches default antenna selection from NIC eeprom word
With these assumptions we can change the antenna configuration
to correctly read both antenna setup values and correctly
configure the antenna. And we can now also configure the antenna
for RF2529 without a double antenna.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antenna switching will be ignored when RX is enabled
during the switch. Make sure we disable the RX during
the switch and don't forget to reenable it later.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version bump.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the config() handler, make sure that we do configure an antenna if the
current active antenna is uninitialized. Furthermore, don't overwrite the
active antenna with bogus values if we didn't touch the antenna setup.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup if-statements for simple 1/0 register field values.
This also fixes a endian bug in rt2500usb when working
with the PHY_CSR2 initialization. As well as a bug
in the enabling of the LED in rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mac80211 indicates that the default antenna setup
should be used _and_ that this default setup is SW_DIVERSITY.
This requires sampling and storing the RSSI per antenna
and check once every 2 seconds to determine if the RSSI
has changed significantly. Once this is the case we should sample
the other antenna for a short period and evaluate if
we need to swap antenna or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt2x00_clear_link() was becoming too large for statically inline,
also it was used on a single location and shouldn't really be
used anywhere else. So move the entire code into the function
rt2x00lib_start_link_tuner()
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although ANTENNA_SW_DIVERSITY should never be send
to the driver, we should still handle it to prevent bugs.
But instead of defaulting to ANTENNA_HW_DIVERSITY we
should default to ANTENNA_B instead.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 has 3 values for the antenna setup:
0 - default
1 - use antenna 1
2 - use antenna 2
This means that rt2x00 should store the default value
from the EEPROM somwhere and use that when mac80211 indicates
that the antenna setup is 0.
This also implies that rt2x00 should no longer write the
hw->config.antenna_sel_* values based on the EEPROM input.
This also adds the basis in rt2x00lib for correct software
diversity handling. By default rt2x00lib will now configure
antenna B instead of hardware diversity.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the default EEPROM values use
the values from the enums instead of "magic" values.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all link quality statistics variables into
the link_qual structure. This cleans up the link
structure and allows us to use it for more then
just statistics.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch extends the inet_addr_type and inet_dev_addr_type with the
network namespace pointer. That allows to access the different tables
relatively to the network namespace.
The modification of the signature function is reported in all the
callers of the inet_addr_type using the pointer to the well known
init_net.
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- 'cb' is a fake struct member. In a previous patch struct cn_callback
was renamed to cn_callback_id, so 'cb' should have been deleted at that
time.
- 'nls' isn't used and is redundant, we can retrieve this data through
cn_callback_entry.pdev->nls.
- 'seq' and 'group' should be u32, as they are declared to be u32 in
other places.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct member netlink_groups is never used, and I don't see how it can
be useful.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- __cn_rx_skb() does nothing but calls cn_call_callback(), it doesn't
check skb and msg sizes as the comment suggests, but cn_rx_skb() checks
those sizes.
- In cn_rx_skb() Local variable 'len' is not used. 'len' is probably
intended to be passed to skb_pull(), but here skb_pull() is not needed,
instead skb_free() is called.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each entry in the list has a unique id, so just break out of the
loop if the matched id is found.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the scheduled removal of the shaper driver.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jorge Boncompte <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
print_mac() used many most net drivers and format_addr() used by
net-sysfs.c are very similar and they can be intergrated.
format_addr() is also identically redefined in the qla4xxx iscsi
driver.
Export a new function sysfs_format_mac() to be used by net-sysfs,
qla4xxx and others in the future. Both print_mac() and
sysfs_format_mac() call _format_mac_addr() to do the formatting.
Changed print_mac() to use unsigned char * to be consistent with
net_device struct's dev_addr. Added buffer length overrun checking
as suggested by Joe Perches.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version number to 3.87.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does three things. It modifies tg3_setup_flow_control() to
use the administrator requested flow control settings if
autonegotiation is turned off. It slightly modifies the
tg3_setup_fiber_mii_phy() function to account for this new use case.
And finally, it does the same for tg3_setup_copper_phy().
The copper modifications are more than a small multi-line change. The
new code makes an attempt to avoid a link renegotiation if the link is
active at half duplex and the only difference between the current
advertised settings and requested advertised settings is the
flow control advertisements.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the software autoneg code to use the administrator
specified flow control parameters. Since the autonegotiation code uses
alternative flow control enumerations, the 1000-BaseX utility functions
are used and code was added to convert the definitions to and from the
alternate enumerations.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the 5704S hardware autoneg code to use the
administrator specified flow control parameters. Since the 5704S uses
device specific flow control enumerations, the 1000-BaseX utility
functions are used and code was added to convert the definitions to and
from the proprietary enumerations.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces magic values with preprocessor definitions for
the sg_dig_ctrl and sg_dig_status registers. This is preparatory work
for the next patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two functions designed to convert abstract TX & RX
flow control parameters to 1000-BaseT and 1000-BaseX autonegotiation
advertisements. Code that uses standard definitions which statically
advertises TX & RX flow control has been replaced with code that
configures the advertisements based on administrator dictated
preferences.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two new utility functions to resolve flow control. One
function resolves flow control based on 1000-BaseT register definitions.
The other resolves flow control based on 1000-Base X register
definitions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the TX and RX flow control flags from tg3_flags and
adds two new flow control variables, flowctrl and active_flowctrl.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move some code out of rc80211_simple since it's probably needed for all rate
selection algorithms, and fix iwlwifi accordingly. While at it, clean up the
rate_control_get_rate() interface.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These drivers pass full mactime information to the stack, make them
indicate this via the new RX_FLAG_TSFT to get mac80211 to show this
information in monitor mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce scan capabilities to WEXT so that userspace can do intelligent
things with scan behavior such as handling hidden SSIDs more gracefully.
If the driver reports a specific scan capability, the driver must
respect the options specified in the iw_scan_req structure when handling
the SIOCSIWSCAN call, unless it's mode or state does not allow it to do
so, in which case it must return an error.
This version switches to Dave Kilroy's suggestion of claiming unused
padding space for the scan_capa field.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP synchronous tty channel driver: convert the semaphore dead_sem to a
completion
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_init_napi() to void.
Warning was noted by DaveM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable new tx ring and add new MSIX handler and NAPI poll function
for the new tx ring. Enable MSIX when the hardware supports it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To separate TX IRQs into a different MSIX vector, we need to
support a new tx ring. The original tx ring will still be used
when not using MSIX.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_napi struct into an array and add code to manage multiple
IRQs. MSIX hardware structures and new registers are also added.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a bnx2_napi structure that will hold a napi_struct and
other fields to handle NAPI polling for the napi_struct. Various tx
and rx indexes and status block pointers will be moved from the main
bnx2 structure to this bnx2_napi structure.
Most NAPI path functions are modified to be passed this bnx2_napi
struct pointer.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a table to keep track of multiple IRQs and restructure the IRQ
request and free functions so that they can be easily expanded to
handle multiple IRQs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the code cleaner and easier to support different tx rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MTU requires more than 1 page for the SKB, enable the page ring
and calculate the size of the page ring. This will guarantee order-0
allocation regardless of the MTU size.
Fixup loopback test packet size so that we don't deal with the pages
during loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to reuse a page in case of allocation or other errors.
Add code to construct the completed SKB with the additional data in
the pages.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields to keep track of the pages and the page rings.
Add functions to allocate and free pages.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the common functions that will be used to initialize the
normal RX rings and the page rings.
Change the copybreak constant RX_COPY_THRESH to 128. This same
constant will be used for the max. size of the linear SKB when pages
are used. Copybreak will be turned off when pages are used.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function to handle new SKB allocation and to prepare the
completed SKB. This makes it easier to add support for non-linear
SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the various ring constants to make the code cleaner.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LOOPBACK_OVERHEAD is not used in this file at all.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
X86_32 was the last user of the FASTCALL macro, now that it
uses regparm(3) by default, this macro expands to nothing.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule bcm43xx for for removal in the 2.6.26 development window.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use iov_length() instead of tun's homemade iov_total().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only devices that are UP are in the hash, so macvlan_broadcast() doesn't
need to check for IFF_UP.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local_mac is managed by the network device, no need to keep a
spare copy and all the management problems that could cause.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the virtual CAN bus (vcan) network driver.
The vcan device is just a loopback device for CAN frames, no
real CAN hardware is involved.
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (197 commits)
sh: add spi header and r2d platform data V3
sh: update r7780rp interrupt code
sh: remove consistent alloc stuff from the machine vector
sh: use declared coherent memory for dreamcast pci ethernet adapter
sh: declared coherent memory support V2
sh: Add support for SDK7780 board.
sh: constify function pointer tables
sh: Kill off -traditional for linker script.
cdrom: Add support for Sega Dreamcast GD-ROM.
sh: Kill off hs7751rvoip reference from arch/sh/Kconfig.
sh: Drop r7780rp_defconfig, use r7780mp_defconfig as kbuild default.
sh: Kill off dead HS771RVoIP board support.
sh: r7785rp: Fix up DECLARE_INTC_DESC() arg mismatch.
sh: r7785rp: Hook up the rest of the HL7785 FPGA IRQ vectors.
sh: r2d - enable sm501 usb host function
sh: remove voyagergx
sh: r2d - add lcd planel timings to sm501 platform data
sh: Add OHCI and UDC platform devices for SH7720.
sh: intc - remove default interrupt priority tables
sh: Correct pte size mismatch for X2 TLB.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (24 commits)
HID: ADS/Tech Radio si470x needs blacklist entry
HID: Logitech Extreme 3D needs NOGET quirk
HID: Refactor MS Presenter 8K key mapping
HID: MS Presenter mapping for PID 0x0701
HID: Support Samsung IR remote
HID: fix compilation of hidbp drivers without usbhid
HID: Blacklist the Gretag-Macbeth Huey display colorimeter
HID: the `bit' in hidinput_mapping_quirks() is an out parameter
HID: remove redundant WARN_ON()s in order not to scare users
HID: force hiddev creation for SONY PS3 controller
HID: Use hid blacklist in usbmouse/usbkbd
HID: proper handling of MS 4k and 6k devices
HID: remove unused variable in quirk event handler
HID: hid-input quirk for BTC 8193
HID: separate hid-input event quirks from generic code
HID: refactor mapping to input subsystem for quirky devices
HID: Microsoft Wireless Optical Desktop 3.0 quirk
HID: Add support for Logitech Elite keyboards
HID: add full support for Genius KB-29E
HID: fix a potential bug in pointer casting
...
* 'sg' of git://git.kernel.dk/linux-2.6-block:
SG: work with the SCSI fixed maximum allocations.
SG: Convert SCSI to use scatterlist helpers for sg chaining
SG: Move functions to lib/scatterlist.c and add sg chaining allocator helpers
The documentation for ata_data_xfer and ata_data_xfer_noirq had the 'rw'
parameter named 'write_data'.
Signed-off-by: Linus Nilsson <lajnold@acc.umu.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds blacklist entries in hid-quirks.c to let the usbhid driver
ignore the si470x radio devices. They are now handled by the new radio-si470x
driver.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Logitech Extreme 3D needs NOGET quirk, otherwise it times out at
the time of connect.
Reported-by: Mike Sharov <msharov@softhome.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Following the suggestion of Jonas, this patch maps the special keys of
the MS Presenter 8000 to targets that should allow for better re-mapping
according to individual use cases (i.e. I avoided hard-wiring to
standard keys). This time I also included the last missing key event
(switching back from presentation mode).
The optimal Xmodmap customization for using the Presenter with
OpenOffice now looks like this for me:
keycode 175 = Escape
keycode 179 = F5
keysym XF86Forward = Right
keysym XF86Back = Left
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
0x045e/0x0701 also needs the hid-input mapping quirk established by
quirk_microsoft_presenter_8k().
Reported-by: Jonas Delrue <jonas_delrue@hotmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Samsung USB remotes (0419:0001) are rejected by kernel 2.6.23, because the
report descriptor from the remote contains a 48 bit HID report field. HID 1.11
states: Fields may span at most 4 bytes.
This patch, based on 2.6.23, fixes this by modifying the internal report
descriptor in hid-quirks.c. Additional user space support (e.g. LIRC) is
required to fetch the information from the hiddev interface.
The burden to reconstruct the data is moved into userspace (lirc through hiddev).
There is no need to set HID_QUIRK_HIDDEV quirk, as the device has also output
applications, which trigger the creation of hiddev device automatically.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We can use the blacklist only if usbhid code is compiled.
Reported-by: jurriaan <thunder7@xs4all.nl>
Cc: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Gretag-Macbeth Huey display colorimeter claims to be an HID device but
isn't. As a result the linux HID device will claim it, preventing FLOSS
software like Argyll CMS from talking to it.
Tested-by: Frederic Crozat <fcrozat@mandriva.com>
Signed-off-by: Nicolas Mailhot <nicolas.mailhot@laposte.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix a panic, by changing
hidinput_mapping_quirks(,, unsigned long *bit,)
to
hidinput_mapping_quirks(,, unsigned long **bit,)
The `bit' in this function is an out parameter.
Signed-off-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The WARN_ON() in implement() and extract() spit out stacktraces and
a lot of other information that might make users think that there is
something seriously wrong with the system. WARN_ON() should not be
deliberately triggerable by userspace application, which these can be.
Usually this WARN_ON() triggers when hid2hci utility is sending the
data that don't correspond to the device's report descriptor.
Convert these messages to more friendly printk().
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device is not discoverable, and needs to be poked to set its master, the
Bluetooth device it will try to connect to when the "Home" button is pressed
without a cable plugged in.
Using libusb means disconnecting the device from its driver to get the report
descriptor. Using hiddev, we can poke it without relinquishing control over it,
so when you plug it in, it would still work as a pad.
This could be then used by sixpair program, after it is rewritten to use
hiddev instead of libusb.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This fixes wacom tablets not working if usbmouse is loaded.
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This removes ugly macros IS_* to distinguish devices that
need special handling in hid-input, and establish proper
quirks for them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
BTC 8193 keyboard handles its scrollwheel in very non-standard way.
It produces two non-standard usages for scrolling up and down, in
both cases with postive value equaling to 1. We handle this by temporary
mapping, which we then catch in quirk event handler, and remap to
negative HWHEEL even in order to introduce correct behavior.
Also the button requires special mapping, as it triggers standard-violating
usage code.
Reported in kernel.org bugzilla #9385
Reported-by: Kir Kolyshkin <kir@sacred.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch separates also the hid-input quirks that have to be
applied at the time the event occurs, so that the generic code
handling HUT-compliant devices is not messed up by them too much.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, the handling of mapping between hid and input for devices
that don't conform to HUT 1.12 specification is very messy -- no per-device
handling, no blacklists, conditions on idVendor and idProduct placed
all over the code.
This patch moves all the device-specific input mapping to a separate
file, and introduces a blacklist-style handling for non-standard
device-specific mappings.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make the Microsoft Wireless Optical Desktop 3.0 work as a mouse.
Microsoft Wireless Optical Desktop 3.0 doesn't properly describe its interface
class. Specifically, since it doesn't mark the second interface as a mouse
(bInterfaceSubclass = 0), it doesn't get HID_QUIRK_NOGET applied to the
interface, and then acts broken when polled.
Signed-off-by: Drew Fisher <drew.m.fisher@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reuse the quirks from the Cordless Desktop LX500 - stops some of the extra
keys being reported as mouse buttons.
Signed-off-by: Carlos Corbacho <cathectic@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Genius KB-29E has broken report descriptor, which causes some of the
Consumer usages to appear incorrectly as Button usages. We fix it by
fixing the report descriptor before it is being parsed.
Also a few of the keys violate the HUT standard, so they need a special
handling. They currently fall into "Reserved" range as per HUT 1.12.
Reported-by: Szekeres Istvan <szekeres@iii.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't directly cast list_head * to foo *, this works only when list
is the first member of struct foo, and we should not make the assumption
how members are ordered in the structure.
i.e. struct *f = (struct *f)pos will work if:
struct foo {
struct list_head list;
int i;
};
but will fail if:
struct foo {
int i;
struct list_head list;
}
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse distinguishes horizontal wheel from vertical by a special "pseudo
event" GenericDesktop.00b8, with values of 0 for vertical and 8 for horizontal
wheel. Because this event is supplied by the parser too late, we need to delay
a wheel event, wait for this one and send either REL_WHEEL or REL_HWHEEL to
input depending on the event value.
Signed-off-by: Pavel Troller <patrol@sinus.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reuse the existing quirks for Apple laptop USB keyboards.
Signed-off-by: Michel Daenzer <michel@tungstengraphics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Preserve identifiers exposed in build and run time configuration though in
order not to break existing configurations.
This is in preparation for adding support for Apple aluminum USB keyboards.
Signed-off-by: Michel Daenzer <michel@tungstengraphics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The MS Presenter 8000 bluetooth mouse is a "dual-use" device: If you
press a button on the top, you can turn it around and find special keys
on the other side, useful for presentations. This patch maps those three
bottom-keys that are not already detected to the intended functions. The
magic bottom on the top is mapped to F5 when we switch from mouse to
presenter mode in order to activate the presentation mode in the related
software (e.g. OpenOffice).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for Toradex' PXA27x based Colibri module.
It's kept as simple as possible to only provide basic functionality.
A default config is also included.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch refactors the code in corgi_lcd.c moving it to the board
specific corgi and spitz files where appropriate instead of the
existing ifdef mess which hinders readability.
Fix spitz_get_hsync_len() to call get_hsync_invperiod so pxafb can be
compiled as a module.
The confusing variables which represent the inverse horizintal sync
period are renamed to "invperiod" consistently.
An incorrect comment in corgi_ts.c is also corrected.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds SMC91x support for the phyCORE-PXA270 CPU module (aka PCM-027).
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
smc91x is shared between many different platforms. Each platform needs
to specify the interrupt type, and in some cases the irq type depends
on more than just the build configuration - it depends on runtime
checks.
Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide
a way for these flags to be passed via the IRQ resource itself.
Note that IRQF_TRIGGER_* constants are intentionally defined to correspond
with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that
the low bits of PCI iomem resources correspond with the BAR flag bits.
Also provide a way to configure smc91x to read the IRQ flags from the
resource. Once all platforms have been converted over (signified
by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should
be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
SCSI sg table allocation has a maximum size (of SCSI_MAX_SG_SEGMENTS,
currently 128) and this will cause a BUG_ON() in SCSI if something
tries an allocation over it. This patch adds a size limit to the
chaining allocator to allow the specification of the maximum
allocation size for chaining, so we always chain in units of the
maximum SCSI allocation size.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts xsysace to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
xsysace is a little bit different from "normal" drivers.
xsysace driver has a state machine in it.
It calls end_that_request_first() and end_that_request_last()
from different states. (ACE_FSM_STATE_REQ_TRANSFER and
ACE_FSM_STATE_REQ_COMPLETE, respectively.)
However, those states are consecutive and without any interruption
inbetween.
So we can just follow the standard conversion rule (b) mentioned in
the patch subject "[PATCH 01/30] blk_end_request: add new request
completion interface".
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts ub to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts scsi mid-layer to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interface of internal function, scsi_end_request(),
is changed.
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts ide-cd (cdrom_newpc_intr()) to use blk_end_request
interfaces. Related 'uptodate' arguments are converted to 'error'.
In PIO mode, ide-cd (cdrom_newpc_intr()) needs to defer
end_that_request_last() until the device clears DRQ_STAT and raises
an interrupt after end_that_request_first().
So blk_end_request() has to return without completing request
even if no leftover in the request.
ide-cd uses blk_end_request_callback() and a dummy callback function,
which just returns value '1', to tell blk_end_request_callback()
about that.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts "normal" parts of ide to use blk_end_request
interfaces. Related 'uptodate' arguments are converted to 'error'.
The conversion of 'uptodate' to 'error' is done only for the internal
function, __ide_end_request().
ide_end_request() was not changed since it's exported and used
by many ide drivers.
With this patch, blkdev_dequeue_request() in __ide_end_request() is
moved to blk_end_request, since blk_end_request takes care of
dequeueing request like below:
if (!list_empty(&rq->queuelist))
blkdev_dequeue_request(rq);
In the case of ide,
o 'dequeue' variable of __ide_end_request() is 1 only when the request
is still linked to the queue (i.e. rq->queuelist is not empty)
o 'dequeue' variable of __ide_end_request() is 0 only when the request
has already been removed from the queue (i.e. rq->queuelist is empty)
So blk_end_request can handle it correctly although ide always run
thought the code above.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts cpqarray to use blk_end_request interfaces.
Related 'ok' arguments are converted to 'error'.
cpqarray is a little bit different from "normal" drivers.
cpqarray directly calls bio_endio() and disk_stat_add()
when completing request. But those can be replaced with
__end_that_request_first().
After the replacement, request completion procedures of
those drivers become like the following:
o end_that_request_first()
o add_disk_randomness()
o end_that_request_last()
This can be converted to __blk_end_request() by following
the rule (b) mentioned in the patch subject
"[PATCH 01/30] blk_end_request: add new request completion interface".
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts cciss to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
cciss is a little bit different from "normal" drivers.
cciss directly calls bio_endio() and disk_stat_add()
when completing request. But those can be replaced with
__end_that_request_first().
After the replacement, request completion procedures of
those drivers become like the following:
o end_that_request_first()
o add_disk_randomness()
o end_that_request_last()
This can be converted to blk_end_request() by following
the rule (a) mentioned in the patch subject
"[PATCH 01/30] blk_end_request: add new request completion interface".
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts s390 to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interfaces of internal functions below are changed:
o dasd_end_request
o tapeblock_end_request
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts mmc to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts i2o_block to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interface of internal function, i2o_block_end_request(),
is changed.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts viocd to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interface of internal function, viocd_end_request(),
is changed.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts xen-blkfront to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts viodasd to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interface of internal function, viodasd_end_request(),
is changed.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts sx8 to use blk_end_request interfaces.
Related 'uptodate' and 'is_ok' arguments are converted to 'error'.
As a result, the interfaces of internal functions below are changed.
o carm_end_request_queued
o carm_end_rq
o carm_handle_array_info
o carm_handle_scan_chan
o carm_handle_generic
o carm_handle_rw
The 'is_ok' is set at only one place in carm_handle_resp() below:
int is_ok = (status == RMSG_OK);
And the value is propagated to all functions above, and no modification
in other places.
So the actual conversion of the 'is_ok' is done at only one place above.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts sunvdc to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interface of internal function, vdc_end_request(),
is changed.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts nbd to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts floppy to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interface of internal function, floppy_end_request(),
is changed.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts DAC960 to use blk_end_request interfaces.
Related 'UpToDate' arguments are converted to 'Error'.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Also change scsi_alloc_sgtable() to just return 0/failure, since it
maps to the command passed in. ->request_buffer is now no longer needed,
once drivers are adapted to use scsi_sglist() it can be killed.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Eliezer Tamir