Expose hop count to destination information in mpath info
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds TX airtime statistics to the cfg80211 station dump (to go along
with the RX info already present), and adds a new parameter to set the
airtime weight of each station. The latter allows userspace to implement
policies for different stations by varying their weights.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[rmanohar@codeaurora.org: fixed checkpatch warnings]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[move airtime weight != 0 check into policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently radar detection and corresponding channel switch is handled
at the AP device. STA ignores these detected radar events since the
radar signal can be seen mostly by the AP as well. But in scenarios where
a radar signal is seen only at STA, notifying this event to the AP which
can trigger a channel switch can be useful.
Stations can report such radar events autonomously through Spectrum
management (Measurement Report) action frame to its AP. The userspace on
processing the report can notify the kernel with the use of the added
NL80211_CMD_NOTIFY_RADAR to indicate the detected event and inturn adding
the reported channel to NOL.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The older code and current userspace assumed that this data
is the content of the Measurement Report element, starting
with the Measurement Token. Clarify this in the documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Spelling errors found by codespell
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When userspace is controlling mesh routing, it may have better
knowledge about whether a mesh STA is connected to a mesh
gate than the kernel mpath table. Add dot11MeshConnectedToMeshGate
to the mesh config so that such applications can explicitly
signal that a mesh STA is connected to a gate, which will then
be advertised in the beacon.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Capture the current state of gate connectivity from the mesh
formation field in mesh config whenever we receive a beacon,
and report that via GET_STATION. This allows applications
doing mesh peering in userspace to make peering decisions
based on peers' current upstream connectivity.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new "peer measurement" API, that can be used to measure
certain things related to a peer. Right now, only implement
FTM (flight time measurement) over it, but the idea is that
it'll be extensible to also support measuring the necessary
things to calculate e.g. angle-of-arrival for WiGig.
The API is structured to have a generic list of peers and
channels to measure with/on, and then for each of those a
set of measurements (again, only FTM right now) to perform.
Results are sent to the requesting socket, including a final
complete message.
Closing the controlling netlink socket will abort a running
measurement.
v3:
- add a bit to report "final" for partial results
- remove list keeping etc. and just unicast out the results
to the requester (big code reduction ...)
- also send complete message unicast, and as a result
remove the multicast group
- separate out struct cfg80211_pmsr_ftm_request_peer
from struct cfg80211_pmsr_request_peer
- document timeout == 0 if no timeout
- disallow setting timeout nl80211 attribute to 0,
must not include attribute for no timeout
- make MAC address randomization optional
- change num bursts exponent default to 0 (1 burst, rather
rather than the old default of 15==don't care)
v4:
- clarify NL80211_ATTR_TIMEOUT documentation
v5:
- remove unnecessary nl80211 multicast/family changes
- remove partial results bit/flag, final is sufficient
- add max_bursts_exponent, max_ftms_per_burst to capability
- rename "frames per burst" -> "FTMs per burst"
v6:
- rename cfg80211_pmsr_free_wdev() to cfg80211_pmsr_wdev_down()
and call it in leave, so the device can't go down with any
pending measurements
v7:
- wording fixes (Lior)
- fix ftm.max_bursts_exponent to allow having the limit of 0 (Lior)
v8:
- copyright statements
- minor coding style fixes
- fix error path leak
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for drivers to report the total number of MPDUs received
and the number of MPDUs received with an FCS error from a specific
peer. These counters will be incremented only when the TA of the
frame matches the MAC address of the peer irrespective of FCS
error.
It should be noted that the TA field in the frame might be corrupted
when there is an FCS error and TA matching logic would fail in such
cases. Hence, FCS error counter might not be fully accurate, but it can
provide help in detecting bad RX links in significant number of cases.
This FCS error counter without full accuracy can be used, e.g., to
trigger a kick-out of a connected client with a bad link in AP mode to
force such a client to roam to another AP.
Signed-off-by: Ankita Bajaj <bankita@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow userspace to enable fine timing measurement responder
functionality with configurable lci/civic parameters in AP mode.
This can be done at AP start or changing beacon parameters.
A new EXT_FEATURE flag is introduced for drivers to advertise
the capability.
Also nl80211 API support for retrieving statistics is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
[remove unused cfg80211_ftm_responder_params, clarify docs,
move validation into policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers able to correctly replace a in-use key should set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to allow the user space (e.g.
hostapd or wpa_supplicant) to rekey PTK keys.
The user space must detect a PTK rekey attempt and only go ahead with it
when the driver has set this flag. If the driver is not supporting the
feature the user space either must not replace the PTK key or perform a
full re-association instead.
Ignoring this flag and continuing to rekey the connection can still work
but has to be considered insecure and broken. Depending on the driver it
can leak clear text packets or freeze the connection and is only
supported to allow the user space to be updated.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Reviewed-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Modify the API to include all ACK frames in average ACK
signal strength reporting, not just ACKs for data frames.
Make exposing the data conditional on implementing the
extended feature flag.
This is how it was really implemented in mac80211, update
the code there to use the new defines and clean up some of
the setting code.
Keep nl80211.h source compatibility by keeping the old names.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[rewrite commit log, change compatibility to be old=new
instead of the other way around, update kernel-doc,
roll in mac80211 changes, make mac80211 depend on valid
bit instead of HW flag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current support in the 60GHz band is for channels 1-4.
Add support for channels 5 and 6.
This requires enlarging ieee80211_channel.center_freq from u16 to u32.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
-----BEGIN PGP SIGNATURE-----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=sNaA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Small merge conflict in net/mac80211/scan.c, I preserved
the kcalloc() conversion. -DaveM
Johannes Berg says:
====================
This round's updates:
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the HE in cfg80211 and also add userspace API to
nl80211 to send rate information out, conforming with P802.11ax_D2.0.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Add the scan flags for randomized SN and minimized probe request
content for improved scan privacy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
There is a bunch of tags marking constants with &, which means struct
or enum name. Replace them with %, which is the correct tag for
constants.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Use NL80211_CMD_UPDATE_CONNECT_PARAMS to update new ERP information,
Association IEs and the Authentication type to driver / firmware which
will be used in subsequent roamings.
Signed-off-by: Vidyullatha Kanchanapally <vidyullatha@codeaurora.org>
[arend: extended fils-sk kernel doc and added check in wiphy_register()]
Reviewed-by: Jithu Jance <jithu.jance@broadcom.com>
Reviewed-by: Eylon Pedinovsky <eylon.pedinovsky@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of FILS shared key offload the parameters can change
upon roaming of which user-space needs to be notified.
Reviewed-by: Jithu Jance <jithu.jance@broadcom.com>
Reviewed-by: Eylon Pedinovsky <eylon.pedinovsky@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bring in net-next which had pulled in net, so I have the changes
from mac80211 and can apply a patch that would otherwise conflict.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wiphy names were recently limited to 128 bytes by commit a7cfebcb75
("cfg80211: limit wiphy names to 128 bytes"). As it turns out though,
this isn't sufficient because dev_vprintk_emit() needs the syslog header
string "SUBSYSTEM=ieee80211\0DEVICE=+ieee80211:$devname" to fit into 128
bytes. This triggered the "device/subsystem name too long" WARN when
the device name was >= 90 bytes. As before, this was reproduced by
syzbot by sending an HWSIM_CMD_NEW_RADIO command to the MAC80211_HWSIM
generic netlink family.
Fix it by further limiting wiphy names to 64 bytes.
Reported-by: syzbot+e64565577af34b3768dc@syzkaller.appspotmail.com
Fixes: a7cfebcb75 ("cfg80211: limit wiphy names to 128 bytes")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support for exporting the mac80211 TXQ stats via nl80211 by
way of a nested TXQ stats attribute, as well as for configuring the
quantum and limits that were previously only changeable through debugfs.
This commit adds just the nl80211 API, a subsequent commit adds support to
mac80211 itself.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Average ack rssi will be given to userspace via NL80211 interface
if firmware is capable. Userspace tool ‘iw’ can process this
information and give the output as one of the fields in
‘iw dev wlanX station dump’.
Example output :
localhost ~ #iw dev wlan-5000mhz station dump Station
34:f3:9a:aa:3b:29 (on wlan-5000mhz)
inactive time: 5370 ms
rx bytes: 85321
rx packets: 576
tx bytes: 14225
tx packets: 71
tx retries: 0
tx failed: 2
beacon loss: 0
rx drop misc: 0
signal: -54 dBm
signal avg: -53 dBm
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
avg ack signal: -56 dBm
authorized: yes
authenticated: yes
associated: yes
preamble: short
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 203 seconds
Main use case is to measure the signal strength of a connected station
to AP. Data packet transmit rates and bandwidth used by station can vary
a lot even if the station is at fixed location, especially if the rates
used are multi stream(2stream, 3stream) rates with different bandwidth(20/40/80 Mhz).
These multi stream rates are sensitive and station can use different transmit power
for each of the rate and bandwidth combinations. RSSI measured from these RX packets
on AP will be not stable and can vary a lot with in a short time.
Whereas 802.11 ack frames from station are sent relatively at a constant
rate (6/12/24 Mbps) with constant bandwidth(20 Mhz).
So average rssi of the ack packets is good and more accurate.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will serve userspace entity to maintain its regulatory limitation.
More specifcally APs can use this data to calculate the WMM IE when
building: beacons, probe responses, assoc responses etc...
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's currently no limit on wiphy names, other than netlink
message size and memory limitations, but that causes issues when,
for example, the wiphy name is used in a uevent, e.g. in rfkill
where we use the same name for the rfkill instance, and then the
buffer there is "only" 2k for the environment variables.
This was reported by syzkaller, which used a 4k name.
Limit the name to something reasonable, I randomly picked 128.
Reported-by: syzbot+230d9e642a85d3fec29c@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit implements the TX side of NL80211_CMD_CONTROL_PORT_FRAME.
Userspace provides the raw EAPoL frame using NL80211_ATTR_FRAME.
Userspace should also provide the destination address and the protocol
type to use when sending the frame. This is used to implement TX of
Pre-authentication frames. If CONTROL_PORT_ETHERTYPE_NO_ENCRYPT is
specified, then the driver will be asked not to encrypt the outgoing
frame.
A new EXT_FEATURE flag is introduced so that nl80211 code can check
whether a given wiphy has capability to pass EAPoL frames over nl80211.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit also adds cfg80211_rx_control_port function. This is used
to generate a CMD_CONTROL_PORT_FRAME event out to userspace. The
conn_owner_nlportid is used as the unicast destination. This means that
userspace must specify NL80211_ATTR_SOCKET_OWNER flag if control port
over nl80211 routing is requested in NL80211_CMD_CONNECT,
NL80211_CMD_ASSOCIATE, NL80211_CMD_START_AP or IBSS/mesh join.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix return value of cfg80211_rx_control_port()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add wiphy EXT_FEATURE flag to indicate that HW or driver does
all DFS actions by itself.
User-space functionality already implemented in hostapd using
vendor-specific (QCA) OUI to advertise DFS offload support.
Need to introduce generic flag to inform about DFS offload support.
For devices with DFS_OFFLOAD flag set user-space will no longer
need to issue CAC or do any actions in response to
"radar detected" events. HW will do everything by itself and send
events to user-space to indicate that CAC was started/finished, etc.
Signed-off-by: Dmitrii Lebed <dlebed@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CAC_STARTED event is needed for DFS offload feature and
should be generated by driver/HW if DFS_OFFLOAD is enabled.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch provides support to get ack signal in probe client response
and in station info from user.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
[squash in compilation fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ht/vht action frames will be sent to AP from station to notify
change of its ht/vht opmode(max bandwidth, smps mode or nss) modified
values. Currently these valuse used by driver/firmware for rate control
algorithm. This patch introduces NL80211_CMD_STA_OPMODE_CHANGED
command to notify those modified/current supported values(max bandwidth,
smps mode, max nss) to userspace application. This will be useful for the
application like steering, which closely monitoring station's capability
changes. Since the application has taken these values during station
association.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This interface allows the host driver to offload the authentication to
user space. This is exclusively defined for host drivers that do not
define separate commands for authentication and association, but rely on
userspace SME (e.g., in wpa_supplicant for the ~WPA_DRIVER_FLAGS_SME
case) for the authentication to happen. This can be used to implement
SAE without full implementation in the kernel/firmware while still being
able to use NL80211_CMD_CONNECT with driver-based BSS selection.
Host driver sends NL80211_CMD_EXTERNAL_AUTH event to start/abort
authentication to the port on which connect is triggered and status
of authentication is further indicated by user space to host
driver through the same command response interface.
User space entities advertise this capability through the
NL80211_ATTR_EXTERNAL_AUTH_SUPP flag in the NL80211_CMD_CONNECT request.
Host drivers shall look at this capability to offload the authentication.
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[add socket connection ownership check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit defines new scan flags (LOW_SPAN, LOW_POWER, HIGH_LATENCY)
to emphasize the requested scan behavior for the driver. These flags
are optional and are mutually exclusive. The implementation of the
respective functionality can be driver/hardware specific.
These flags can be used to control the compromise between how long
a scan takes, how much power it uses, and high accurate/complete
the scan is in finding the BSSs.
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit enhances the scan results to report the per chain signal
strength based on the latest BSS update. This provides similar
information to what is already available through STA information.
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the regulatory database is loaded, and then updated, it may
be necessary to reload it. Add an nl80211 command to do this.
Note that this just reloads the database, it doesn't re-apply
the rules from it immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an event that indicates that a connection is authorized
(i.e. the 4 way handshake was performed by the driver). This event
should be sent by the driver after sending a connect/roamed event.
This is useful for networks that require 802.1X authentication.
In cases that the driver supports 4 way handshake offload, but the
802.1X authentication is managed by user space, the driver needs to
inform user space right after the 802.11 association was completed
so user space can initialize its 802.1X state machine etc.
However, it is also possible that the AP will choose to skip the
802.1X authentication (e.g. when PMKSA caching is used) and proceed
with the 4 way handshake immediately. In this case the driver needs
to inform user space that 802.1X authentication is no longer required
(e.g. to prevent user space from disconnecting since it did not get
any EAPOLs from the AP).
This is also useful for roaming, in which case it is possible that
the driver used the Fast Transition protocol so 802.1X is not
required.
Since there will now be a dedicated notification indicating that the
connection is authorized, the authorized flag can be removed from the
roamed event. Drivers can send the new port authorized event right
after sending the roamed event to indicate the new AP is already
authorized. This therefore reserves the old PORT_AUTHORIZED attribute.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The user space can now allow the kernel to associate to an AP that
requires MFP or that doesn't have MFP enabled in the same
NL80211_CMD_CONNECT command, by using a new NL80211_MFP_OPTIONAL flag.
The driver / firmware will decide whether to use it or not.
Include a feature bit to advertise support for NL80211_MFP_OPTIONAL.
This allows new user space to run on old kernels and know that it
cannot use the new attribute if it isn't supported.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add Optimized Connectivity Experience (OCE) scan and capability flags.
Some of them unique to OCE and some are stand alone.
And add scan flags to enable/disable them.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If NAN interface is created with NL80211_ATTR_SOCKET_OWNER, the socket
that is used to create the interface is used for all NAN operations and
reporting NAN events.
However, it turns out that sending commands and receiving events on
the same socket is not possible in a completely race-free way:
If the socket buffer is overflowed by the events, the command response
will not be sent. In that case the caller will block forever on recv.
Using non-blocking socket for commands is more complicated and still
the command response or ack may not be received.
So, keep unicasting NAN events to the interface creator, but allow
using a different socket for commands.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The description of NL80211_CMD_ROAM indicated possibility for a
request to roam issued by user-space. However, it also states that
as not being implemented right now. This has been so since commit
b23aa676ab ("cfg80211: connect/disconnect API") added in 2009.
So it seems safe to assume it will not be added any time soon and
thus remove it.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that initiate roaming while being connected to a network that
uses 802.1X authentication need to inform user space if 802.1X
authentication is further required after roaming.
For example, when using the Fast transition protocol, roaming within
the mobility domain does not require new 802.1X authentication, but
roaming to another mobility domain does.
In addition, some drivers may not support 802.1X authentication
(so it has to be done in user space), while other drivers do.
Add a flag to the roaming notification to indicate if user space is
required to do 802.1X authentication after the roaming or not.
This flag will only be used for networks that use 802.1X
authentication. For networks that do not use 802.1X authentication it
is assumed that no further action is required from user space after
the roaming notification.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[arend.vanspriel@broadcom.com reuse NL80211_ATTR_PORT_AUTHORIZED]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[rebase to apply w/o the flag in CONNECT]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add API for setting the PMK to the driver. For FT support, allow
setting also the PMK-R0 Name.
This can be used by drivers that support 4-Way handshake offload
while IEEE802.1X authentication is managed by upper layers.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[arend.vanspriel@broadcom.com: add WANT_1X_4WAY_HS attribute]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X docs a bit to
say that the device may require it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let drivers advertise support for station-mode 4-way handshake
offloading with a new NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK flag.
Extend use of NL80211_ATTR_PMK attribute indicating it might be passed
as part of NL80211_CMD_CONNECT command, and contain the PSK (which is
the PMK, hence the name.)
The driver/device is assumed to handle the 4-way handshake by
itself in this case (including key derivations, etc.), instead
of relying on the supplicant.
This patch is somewhat based on this one (by Vladimir Kondratiev):
https://patchwork.kernel.org/patch/1309561/.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[arend.vanspriel@broadcom.com rebase dealing with existing ATTR_PMK]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK docs to indicate
that this offload might be required]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch allows for the scheduled scan request to specify matchsets
for specific BSSIDs.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[docs, netlink policy fix]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enhance nl80211 and cfg80211 connect request and response APIs to
support FILS shared key authentication offload. The new nl80211
attributes can be used to provide additional information to the driver
to establish a FILS connection. Also enhance the set/del PMKSA to allow
support for adding and deleting PMKSA based on FILS cache identifier.
Add a new feature flag that drivers can use to advertize support for
FILS shared key authentication and association in station mode when
using their own SME.
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
DFS requirement for ETSI domain (section 4.7.1.4 in
ETSI EN 301 893 V1.8.1) is the only one which explicitly
states that once DFS channel is marked as available afer
the CAC, this channel will remain in available state even
moving to a different operating channel. But the same is
not explicitly stated in FCC DFS requirement. Also, Pre-CAC
requriements are not explicitly mentioned in FCC requirement.
Current implementation in keeping DFS channel in available
state is same as described in ETSI domain.
For non-ETSI DFS domain, this patch gives a grace period of 2 seconds
since the completion of successful CAC before moving the channel's
DFS state to 'usable' from 'available' state. The same grace period
is checked against the channel's dfs_state_entered timestamp while
deciding if a DFS channel is available for operation. There is a new
radar event, NL80211_RADAR_PRE_CAC_EXPIRED, reported when DFS channel
is moved from available to usable state after the grace period. Also
make sure the DFS channel state is reset to usable once the beaconing
operation on that channel is brought down (like stop_ap, leave_ibss
and leave_mesh) in non-ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the SET CQM command's RSSI threshold attribute to accept any
number of thresholds as a sorted array. The API should be backwards
compatible so that if one s32 threshold value is passed, the old
mechanism is enabled. The netlink event generated is the same in both
cases.
cfg80211 handles an arbitrary number of RSSI thresholds but drivers have
to provide a method (set_cqm_rssi_range_config) that configures a range
set by a high and a low value. Drivers have to call back when the RSSI
goes out of that range and there's no additional event for each time the
range is reconfigured as there was with the current one-threshold API.
This method doesn't have a hysteresis parameter because there's no
benefit to the cfg80211 code from having the hysteresis be handled by
hardware/driver in terms of the number of wakeups. At the same time
it would likely be less consistent between drivers if offloaded or
done in the drivers.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The nl80211_nan_dual_band_conf enumeration doesn't make much sense.
The default value is assigned to a bit, which makes it weird if the
default bit and other bits are set at the same time.
To improve this, get rid of NL80211_NAN_BAND_DEFAULT and add a wiphy
configuration to let the drivers define which bands are supported.
This is exposed to the userspace, which then can make a decision on
which band(s) to use. Additionally, rename all "dual_band" elements
to "bands", to make things clearer.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enhances the connect timeout API to also carry the reason for the
timeout. These reason codes for the connect time out are represented by
enum nl80211_timeout_reason and are passed to user space through a new
attribute NL80211_ATTR_TIMEOUT_REASON (u32).
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[keep gfp_t argument last]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enhance sched scan to support option of finding a better BSS while in
connected state. Firmware scans the medium and reports when it finds a
known BSS which has better RSSI than the current connected BSS. New
attributes to specify the relative RSSI (compared to the current BSS)
are added to the sched scan to implement this.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to use a random local address (Address 2 = TA in transmit
and the same address in receive functionality) for Public Action frames
in order to improve privacy of WLAN clients. Applications fill the
random transmit address in the frame buffer in the NL80211_CMD_FRAME
command. This can be used only with the drivers that indicate support
for random local address by setting the new
NL80211_EXT_FEATURE_MGMT_TX_RANDOM_TA and/or
NL80211_EXT_FEATURE_MGMT_TX_RANDOM_TA_CONNECTED in ext_features.
The driver needs to configure receive behavior to accept frames to the
specified random address during the time the frame exchange is pending
and such frames need to be acknowledged similarly to frames sent to the
local permanent address when this random address functionality is not
used.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, this attribute is only fetched on station addition, but
not on station change. Since this info is only present in the assoc
request, with full station state support in the driver it cannot be
present when the station is added.
Thus, add support for changing the VHT opmode on station update if
done before (or while) the station is marked as associated. After
this, ignore it, since it used to be ignored.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disconnect or deauthenticate when the owning socket is closed if this
flag is supplied to CMD_CONNECT or CMD_ASSOCIATE. This may be used
to ensure userspace daemon doesn't leave an unmanaged connection behind.
In some situations it would be possible to account for that, to some
degree, in the deamon restart code or in the up/down scripts without
the use of this attribute. But there will be systems where the daemon
can go away for varying periods without a warning due to local resource
management.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The two fields in struct nl80211_bss_select_rssi_adjust did not state
their type or unit. Adding documentation.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NL80211_ATTR_MAC was used to set both the specific BSSID to be scanned
and the random MAC address to be used when privacy is enabled. When both
the features are enabled, both the BSSID and the local MAC address were
getting same value causing Probe Request frames to go with unintended
DA. Hence, this has been fixed by using a different NL80211_ATTR_BSSID
attribute to set the specific BSSID (which was the more recent addition
in cfg80211) for a scan.
Backwards compatibility with old userspace software is maintained to
some extent by allowing NL80211_ATTR_MAC to be used to set the specific
BSSID when scanning without enabling random MAC address use.
Scanning with random source MAC address was introduced by commit
ad2b26abc1 ("cfg80211: allow drivers to support random MAC addresses
for scan") and the issue was introduced with the addition of the second
user for the same attribute in commit 818965d391 ("cfg80211: Allow a
scan request for a specific BSSID").
Fixes: 818965d391 ("cfg80211: Allow a scan request for a specific BSSID")
Signed-off-by: Vamsi Krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add functionality to update the connection parameters when in connected
state, so that driver/firmware uses the updated parameters for
subsequent roaming. This is for drivers that support internal BSS
selection and roaming. The new command does not change the current
association state, i.e., it can be used to update IE contents for future
(re)associations without causing an immediate disassociation or
reassociation with the current BSS.
This commit implements the required functionality for updating IEs for
(Re)Association Request frame only. Other parameters can be added in
future when required.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability to configure if an AP (and associated VLANs) will
do multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own MAC
address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[fix disabling, add better documentation & commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new nl80211 attributes can be used to provide KEK and nonces to
allow the driver to encrypt and decrypt FILS (Re)Association
Request/Response frames in station mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This defines authentication algorithms for FILS (IEEE 802.11ai).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This defines a feature flag that drivers can use to indicate that they
support FILS authentication/association (IEEE 802.11ai) when using user
space SME (NL80211_CMD_AUTHENTICATE) in station mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds defines and nl80211 extensions to allow FILS Authentication to
be implemented similarly to SAE. FILS does not need the special rules
for the Authentication transaction number and Status code fields, but it
does need to add non-IE fields. The previously used
NL80211_ATTR_SAE_DATA can be reused for this to avoid having to
duplicate that implementation. Rename that attribute to more generic
NL80211_ATTR_AUTH_DATA (with backwards compatibility define for
NL80211_SAE_DATA).
Also document the special rules related to the Authentication
transaction number and Status code fiels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit provides a mechanism for the host drivers to advertise the
support for different beacon intervals among the respective interface
combinations in a group, through NL80211_IFACE_COMB_BI_MIN_GCD (u32).
This value will be compared against GCD of all beaconing interfaces of
matching combinations.
If the driver doesn't advertise this value, the old behaviour where
all beacon intervals must be identical is retained.
If it is specified, then any beacon interval for an interface in the
interface combination as well as the GCD of all active beacon intervals
in the combination must be greater or equal to this value.
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
[change commit message, some variable names, small other things]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide a function that reports NAN DE function termination. The function
may be terminated due to one of the following reasons: user request,
ttl expiration or failure.
If the NAN instance is tied to the owner, the notification will be
sent to the socket that started the NAN interface only
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide a function the driver can call to report a match.
This will send the event to the user space.
If the NAN instance is tied to the owner, the notifications will be
sent to the socket that started the NAN interface only.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some NAN configuration paramaters may change during the operation of
the NAN device. For example, a user may want to update master preference
value when the device gets plugged/unplugged to the power.
Add API that allows to do so.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A NAN function can be either publish, subscribe or follow
up. Make all the necessary verifications and just pass the
request to the driver.
Allow the user space application that starts NAN to
forbid any other socket to add or remove functions.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows user space to start/stop NAN interface.
A NAN interface is like P2P device in a few aspects: it
doesn't have a netdev associated to it.
Add the new interface type and prevent operations that
can't be executed on NAN interface like scan.
Define several attributes that may be configured by user space
when starting NAN functionality (master preference and dual
band operation)
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous commit added support for specifying the beacon rate
for AP mode. Add features checks to this, and extend it to also
support the rate configuration for mesh networks. For IBSS it's
not as simple due to joining etc., so that's not yet supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
adds mesh peer AID setting API.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add API to support VHT MU-MIMO air sniffer.
in MU-MIMO there are parallel frames on the air while the HW
has only one RX.
add the capability to sniff one of the MU-MIMO parallel frames by
giving the sniffer additional information so it'll know which
of the parallel frames it shall follow.
Add attribute - NL80211_ATTR_MU_MIMO_GROUP_DATA - for getting
a MU-MIMO groupID in order to monitor packets from that group
using VHT MU-MIMO.
And add attribute -NL80211_ATTR_MU_MIMO_FOLLOW_ADDR - for passing
MAC address to monitor mode.
that option will be used by VHT MU-MIMO air sniffer to follow a
station according to it's MAC address using VHT MU-MIMO.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver extended capabilities may differ for different
interface types which the userspace needs to know (for
example the fine timing measurement initiator and responder
bits might differ for a station and AP). Add a new nl80211
attribute to provide extended capabilities per interface type
to userspace.
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the status parameter to cfg80211_connect_result() was
documented as using WLAN_STATUS_UNSPECIFIED_FAILURE (1) when the real
status code for the failure is not known. This value can be used by an
AP (and often is) and as such, user space cannot distinguish between
explicitly rejected authentication/association and not being able to
even try to associate or not receiving a response from the AP.
Add a new inline function, cfg80211_connect_timeout(), to be used when
the driver knows that the connection attempt failed due to a reason
where connection could not be attempt or no response was received from
the AP. The internal functions now allow a negative status value (-1) to
be used as an indication of this special case. This results in the
NL80211_ATTR_TIMED_OUT to be added to the NL80211_CMD_CONNECT event to
allow user space to determine this case was hit. For backwards
compatibility, NL80211_STATUS_CODE with the value
WLAN_STATUS_UNSPECIFIED_FAILURE is still indicated in the event in such
a case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[johannes: fix cfg80211_connect_bss() prototype to use int for status,
add cfg80211_connect_timeout() to docbook, fix docbook]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Nicolas converted most users, but didn't realize some were generated
by macros. Convert those over as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Nicolas's patch missed this, now generating docbook warnings.
Add the missing descriptions to address that.
Fixes: 2dad624e6d ("wireless: use nla_put_u64_64bit()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the a station statistics netlink attribute:
NL80211_STA_INFO_RX_DURATION.
If present, this attribute contains the aggregate PPDU duration (in
microseconds) for all the frames from the peer. This is useful to
help understand the total time spent transmitting to us by all of
the connected peers.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The roaming cases for the Connect command were not fully covered and
neither Connect nor Associate command uses of the prev_bssid parameter
were very clear. Add details to describe how the prev_bssid argument is
supposed to be used and when the driver should use association or
reassociation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy clients don't support P2P power save mechanisms, and thus
if a P2P GO has a legacy client connected to it, it has to make
some changes in the PS behavior.
To handle this, add an attribute to specify whether a station supports
P2P PS or not. If the attribute was not specified cfg80211 will assume
that station supports it for P2P GO interface, and does NOT support it
for AP interface, matching the current assumptions in the code.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introducing a new feature that the driver can use to
indicate the driver/firmware supports configuration of BSS
selection criteria upon CONNECT command. This can be useful
when multiple BSS-es are found belonging to the same ESS,
ie. Infra-BSS with same SSID. The criteria can then be used to
offload selection of a preferred BSS.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Lei Zhang <leizh@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[move wiphy support check into parse_bss_select()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows scans for a specific BSSID to be optimized by the user space
application by requesting the driver to set the Probe Request frame
BSSID field (Address 3) to the specified BSSID instead of the wildcard
BSSID. This prevents other APs from replying which reduces airtime need
and latency in getting the response from the target AP through.
This is an optimization and as such, it is acceptable for some of the
drivers not to support the mechanism. If not supported, the wildcard
BSSID will be used and more responses may be received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today, the supplicant will add the RRM capabilities
Information Element in the association request only if
Quiet period is supported (NL80211_FEATURE_QUIET).
Quiet is one of many RRM features, and there are other RRM
features that are not related to Quiet (e.g. neighbor
report). Therefore, requiring Quiet to enable RRM is too
restrictive.
Some of the features, like neighbor report, can be
supported by user space without any help from the kernel.
Hence adding the RRM capabilities IE to association request
should be the sole user space's decision.
Removing the RRM dependency on Quiet in the driver solves
this problem, but using an old driver with a user space
tool that would not require Quiet feature would be
problematic: the user space would add NL80211_ATTR_USE_RRM
in the association request even if the kernel doesn't
advertize NL80211_FEATURE_QUIET and the association would
be denied by the kernel.
This solution adds a global RRM capability, that tells user
space that it can request RRM capabilities IE publishment
without any specific feature support in the kernel.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for 11ad devices.
Add support for PBSS by introducing a new PBSS flag attribute.
The PBSS flag is used in the START_AP command to request starting
a PCP instead of an AP, and in the CONNECT command to request
connecting to a PCP instead of an AP.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement new functionality for aborting an ongoing scan.
Add NL80211_CMD_ABORT_SCAN to the nl80211 interface. After
aborting the scan, driver shall provide the scan status by
calling cfg80211_scan_done().
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[change command to take wdev instead of netdev so that it
can be used on p2p-device scans]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In this attribute's documentation, it was not clear whether the delay
started counting when WoWLAN net-detect was enabled or when the system
was suspended. The correct answer is that it starts when the system
suspends (which is when, in practice, the scan is scheduled). Clarify
that in the nl80211.h documentation.
Suggested-by: Samuel Tan <samueltan@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the option to configure multiple 'scan plans' for scheduled scan.
Each 'scan plan' defines the number of scan cycles and the interval
between scans. The scan plans are executed in the order they were
configured. The last scan plan will always run infinitely and thus
defines only the interval between scans.
The maximum number of scan plans supported by the device and the
maximum number of iterations in a single scan plan are advertised
to userspace so it can configure the scan plans appropriately.
When scheduled scan results are received there is no way to know which
scan plan is being currently executed, so there is no way to know when
the next scan iteration will start. This is not a problem, however.
The scan start timestamp is only used for flushing old scan results,
and there is no difference between flushing all results received until
the end of the previous iteration or the start of the current one,
since no results will be received in between.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For location and connectivity services, userspace would often like
to know the time when the BSS was last seen. The current "last seen"
value is calculated in a way that makes it less useful, especially
if the system suspended in the meantime.
Add the ability for the driver to report a real CLOCK_BOOTTIME stamp
that can then be reported to userspace (if present).
Drivers wishing to use this must be converted to the new API to call
cfg80211_inform_bss_data() or cfg80211_inform_bss_frame_data(). They
need to ensure the reported value is accurate enough even when the
frame might have been buffered in the device (e.g. firmware.)
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
[modified to use struct, inlines]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The GO_CONCURRENT regulatory definition can be extended to station
interfaces requesting to IR as part of TDLS off-channel operations.
Rename the GO_CONCURRENT flag to IR_CONCURRENT and allow the added
use-case.
Change internal users of GO_CONCURRENT to use the new definition.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Just clarify that the delay is only before the first cycle.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the indoor setting configuration assumed that as
long as a station interface is connected, the indoor environment
setting does not change. However, this assumption is problematic
as:
- It is possible that a station interface is connected to a mobile
AP, e.g., softAP or a P2P GO, where it is possible that both the
station and the mobile AP move out of the indoor environment making
the indoor setting invalid. In such a case, user space has no way to
invalidate the setting.
- A station interface disconnection does not necessarily imply that
the device is no longer operating in an indoor environment, e.g.,
it is possible that the station interface is roaming but is still
stays indoor.
To handle the above, extend the indoor configuration API to allow
user space to indicate a change of indoor settings, and allow it to
indicate weather it controls the indoor setting, such that:
1. If the user space process explicitly indicates that it is going
to control the indoor setting, do not clear the indoor setting
internally, unless the socket is released. The user space process
should use the NL80211_ATTR_SOCKET_OWNER attribute in the command
to state that it is going to control the indoor setting.
2. Reset the indoor setting when restoring the regulatory settings in
case it is not owned by a user space process.
Based on the above, a user space tool that continuously monitors the
indoor settings, i.e., tracking power setting, location etc., can
indicate environment changes to the regulatory core.
It should be noted that currently user space is the only provided mechanism
used to hint to the regulatory core over the indoor/outdoor environment --
while the country IEs do have an environment setting this has been completely
ignored by the regulatory core by design for a while now since country IEs
typically can contain bogus data.
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: ArikX Nemtsov <arik@wizery.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device supports waking up on 'any' signal - i.e. it continues
operating as usual and wakes up the host on pretty much anything that
happens, then it makes no sense to also configure the more restricted
WoWLAN mode where the device operates more autonomously but also in a
more restricted fashion.
Currently only cw2100 supports both 'any' and other triggers, but it
seems to be broken as it doesn't configure anything to the device, so
we can't currently get into a situation where both even can correctly
be configured. This is about to change (Intel devices are going to
support both and have different behaviour depending on configuration)
so make sure the conflicting modes cannot be configured.
(It seems that cw2100 advertises 'any' and 'disconnect' as a means of
saying that's what it will always do, but that isn't really the way
this API was meant to be used nor does it actually mean anything as
'any' always implies 'disconnect' already, and the driver doesn't
change device configuration in any way depending on the settings.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add notes about userspace ABI/API modifications, including the
fact that we decided that API submissions should come with a
driver implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_EXT_FEATURE_VHT_IBSS flag and VHT
support for IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both wpa_supplicant and mac80211 have and inactivity timer. By default
wpa_supplicant will be timed out in 5 minutes and mac80211's it is 30
minutes. If wpa_supplicant uses a longer timer than mac80211, it will
get unexpected disconnection by mac80211.
Using 0xffffffff instead as the configured value could solve this w/o
changing the code, but due to integer overflow in the expression used
this doesn't work. The expression is:
(current jiffies) > (frame Rx jiffies + NL80211_MESHCONF_PLINK_TIMEOUT * 250)
On 32bit system, the right side would overflow and be a very small
value if NL80211_MESHCONF_PLINK_TIMEOUT is sufficiently large,
causing unexpectedly early disconnections.
Instead allow disabling the inactivity timer to avoid this situation,
by passing the (previously invalid and useless) value 0.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[reword/rewrap commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Such a feature doesn't exist and isn't really needed since you
probably won't have enough interfaces to make it worthwhile, so
just remove that from the documentation.
Reported-by: booto [on IRC]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The userspace may want to delay the the first scheduled scan or
net-detect cycle. Add an optional attribute to the scheduled scan
configuration to pass the delay to be (optionally) used by the driver.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[add the attribute to the policy to validate it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Added new NL80211_ATTR_NETNS_FD which allows to
set namespace via nl80211 by fd.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For some reason, we made the bandwidth separate flags, which
is rather confusing - a single rate cannot have different
bandwidths at the same time.
Change this to no longer be flags but use a separate field
for the bandwidth ('bw') instead.
While at it, add support for 5 and 10 MHz rates - these are
reported as regular legacy rates with their real bitrate,
but tagged as 5/10 now to make it easier to distinguish them.
In the nl80211 API, the flags are preserved, but the code
now can also clearly only set a single one of the flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These rates are treated the same as 160 MHz in the spec, so
it makes no sense to distinguish them. As no driver uses them
yet, this is also not a problem, just remove them.
In the userspace API the field remains reserved to preserve
API and ABI.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send the netdetect configuration information in the response to
NL8021_CMD_GET_WOWLAN commands. This includes the scan interval,
SSIDs to match and frequencies to scan.
Additionally, add the NL80211_WOWLAN_TRIG_NET_DETECT with
NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The base for the current statistics is pretty mixed up, support
exporting RX/TX statistics for MSDUs per TID. This (currently)
covers received MSDUs, transmitted MSDUs and retries/failures
thereof.
Doing it per TID for MSDUs makes more sense than say only per AC
because it's symmetric - we could export per-AC statistics for all
frames (which AC we used for transmission can be determined also
for management frames) but per TID is better and usually data
frames are really the ones we care about. Also, on RX we can't
determine the AC - but we do know the TID for any QoS MPDU we
received.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current statistics we keep aren't very clear, some are on
MPDUs and some on MSDUs/MMPDUs. Clarify the descriptions based
on the counters mac80211 keeps.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add these two values:
* BEACON_RX: number of beacons received from this peer
* BEACON_SIGNAL_AVG: signal strength average for beacons only
These can then be used for Android Lollipop's statistics request.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is really just duplicating the list of information that's
already available in the nl80211 attribute, so remove the list.
Two small changes are needed:
* remove STATION_INFO_ASSOC_REQ_IES complete, but the length
(assoc_req_ies_len) can be used instead
* add NL80211_STA_INFO_RX_DROP_MISC which exists internally
but not in nl80211 yet
This gets rid of the duplicate maintenance of the two lists.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the time spent scanning to the survey data so it can be
reported by drivers that collect such information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not all devices are able to report survey data (particularly
time spent for various operations) per channel. As all these
statistics already exist in survey data, allow such devices
to report them (if userspace requested it)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All of the survey data is (currently) per channel anyway,
so having the word "channel" in the name does nothing. In
the next patch I'll introduce global data to the survey,
where the word "channel" is actually confusing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put the group names into the userspace API header file so that
userspace clients can use symbolic names from there instead of
hardcoding the actual names. This doesn't really change much,
but seems somewhat cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the wiphy::features flag being used up this patch adds a
new field wiphy::ext_features. Considering extensibility this
new field is declared as a byte array. This extensible flag is
exposed to user-space by NL80211_ATTR_EXT_FEATURES.
Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Gautam (Gautam Kumar) Shukla <gautams@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flag is no longer used (and hasn't been for a long time)
since trying to track authentication (and make decisions based
on state) was just causing issues all over - see commit
95de817b90.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some network cards (Intel) produce per-channel regdomains and rely on
cfg80211 to merge rules as needed. This hits the max rules limit and
fails.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An attribute NL80211_ATTR_SOCKET_OWNER can be set by the scan initiator.
If present, the attribute will cause the scan to be stopped if the client
dies.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a device has self-managed regulatory, insist on returning the wiphy
specific regdomain if a wiphy-idx is specified. The global regdomain is
meaningless for such devices.
Also add an attribute for self-managed devices, so usermode can
distinguish them as such.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new regulatory flag that allows a driver to manage regdomain
changes/updates for its own wiphy.
A self-managed wiphys only employs regulatory information obtained from
the FW and driver and does not use other cfg80211 sources like
beacon-hints, country-code IEs and hints from other devices on the same
system. Conversely, a self-managed wiphy does not share its regulatory
hints with other devices in the system. If a system contains several
devices, one or more of which are self-managed, there might be
contradictory regulatory settings between them. Usage of flag is
generally discouraged. Only use it if the FW/driver is incompatible
with non-locally originated hints.
A new API lets the driver send a complete regdomain, to be applied on
its wiphy only.
After a wiphy-specific regdomain change takes place, usermode will get
a new type of change notification. The regulatory core also takes care
enforce regulatory restrictions, in case some interfaces are on
forbidden channels.
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a wiphy-idx is specified, the kernel will return the wiphy specific
regdomain, if such exists. Otherwise return the global regdom.
When no wiphy-idx is specified, return the global regdomain as well as
all wiphy-specific regulatory domains in the system, via a new nested
list of attributes.
Add a new attribute for each wiphy-specific regdomain, for usermode to
identify it as such.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.
Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace NL80211_ATTR_IFACE_SOCKET_OWNER attribute with more generic
NL80211_ATTR_SOCKET_OWNER that can be used with other commands
that interface creation.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary feature flags and a scan flag to support using
random MAC addresses for scan while unassociated.
The configuration for this supports an arbitrary MAC address
value and mask, so that any kind of configuration (e.g. fixed
OUI or full 46-bit random) can be requested. Full 46-bit random
is the default when no other configuration is passed.
Also add a small helper function to use the addr/mask correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new WoWLAN API to enable net-detect as a wake up trigger.
Net-detect allows the device to scan in the background while the
host is asleep to wake up the host system when a matching network
is found.
Reuse the scheduled scan attributes to specify how the scan is
performed while suspended and the matches that will trigger a
wake event.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce commands to initiate and cancel TDLS channel-switching. Once
TDLS channel-switching is started, the lower level driver is responsible
for continually initiating channel-switch operations and returning to
the base (AP) channel to listen for beacons from time to time.
Upon cancellation of the channel-switch all communication between the
relevant TDLS peers will continue on the base channel.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define some related TDLS protocol constants and advertise channel switch
support in the extended-capabilities IE when the feature bit is defined.
Actually supporting TDLS channel-switching also requires support for
some new nl80211 commands, to be introduced by future patches.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow setting bandwidth related regulatory flags. These flags are mapped
to the corresponding channel flags in the specified range.
Make sure the new flags are consulted when calculating the maximum
bandwidth allowed by a regulatory-rule.
Also allow propagating the GO_CONCURRENT modifier from a reg-rule to a
channel.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multi-vif channel switches, we want to send
NL80211_CMD_CH_SWITCH_NOTIFY to the userspace to let it decide whether
other interfaces need to be moved as well. This is needed when we
want a P2P GO interface to follow the channel of a station, for
example.
Modify the code so that all interfaces can send CSA notifications.
Additionally, send notifications for STA CSA as well.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new NL80211_CH_SWITCH_STARTED_NOTIFY message that can be sent to
the userspace when a channel switch process has started. This allows
userspace to take action, for instance, by requesting other interfaces
to switch channel as necessary.
This patch introduces a function that allows the drivers to send this
notification. It should be used when the driver starts processing a
channel switch initiated by a remote device (eg. when a STA receives a
CSA from the AP) and when it successfully starts a userspace-triggered
channel switch (eg. when hostapd triggers a channel swith in the AP).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful when creating virtual interfaces.
Keeps udev from mucking with things it shouldn't, since
the default MAC is never seen by udev when specified on
the cmd-line during creation.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[check for feature flag in nl80211 to force drivers to set it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During the review of the corresponding wpa_supplicant patches we
noticed that the only way for it to detect that this functionality
is supported currently is to check for the command support. This
can be misleading though, as the command was also designed to, in
the future, support pure 802.11 TSPECs.
Expose the WMM-TSPEC feature flag to nl80211 so later we can also
expose an 802.11-TSPEC feature flag (if needed) to differentiate
the two cases.
Note: this change isn't needed in 3.18 as there's no driver there
yet that supports the functionality at all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The optional NL80211_ATTR_MGMT_SUBTYPE and NL80211_ATTR_REASON_CODE
attributes can now be included in NL80211_CMD_DEL_STATION to indicate to
the driver which frame (Deauthentication/Disassociation) and reason code
in that frame should be used to indicate removal to the specific
station. This is used by drivers that implement AP SME and generate
those frames internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add two new cfg80211 operations for querying a table with proxied mesh
paths.
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add feature bits to indicate device support for
static-smps and dynamic-smps modes.
Add a new NL80211_ATTR_SMPS_MODE attribue to allow
configuring the smps mode to be used by the ap
(e.g. configuring to ap to dynamic smps mode will
reduce power consumption while having minor effect
on throughput)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add nl80211 and driver API to validate, add and delete traffic
streams with appropriate settings.
The API calls for userspace doing the action frame handshake
with the peer, and then allows only to set up the parameters
in the driver. To avoid setting up a session only to tear it
down again, the validate API is provided, but the real usage
later can still fail so userspace must be prepared for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable ACK timeout estimation algorithm (dynack) using mac80211
set_coverage_class API. Dynack is activated passing coverage class equals to -1
to lower drivers and it is automatically disabled setting valid value for
coverage class.
Define NL80211_ATTR_WIPHY_DYN_ACK flag attribute to enable dynack from
userspace. In order to activate dynack NL80211_FEATURE_ACKTO_ESTIMATION feature
flag must be set by lower drivers to indicate dynack capability.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a flag attribute to use in associations, for tagging the target
connection as supporting RRM. It is the responsibility of upper
layers to set this flag only if both the underlying device, and the
target network indeed support RRM.
To be used in ASSOCIATE and CONNECT commands.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Radio Resource Measurement (RRM) is a bundle of features which will
require the entire stack to participate.
In this patch, the driver is given the opportunity to advertise the
device's support for these RRM-related features, using feature flags:
1. Support for Quiet IEs.
2. Support for adding DS Parameter Set IE to probe requests.
3. Support for adding WFA TPC Report IE to probe requests.
4. Support for inserting tx power value to tx-ed packets at a fixed
offset. This is used in action frames, such as RRM's Link
Measurement Report, where the actual tx power should be reported
in the frame.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few possible cases of where BSS data came from:
1) only a beacon has been received
2) only a probe response has been received
3) the driver didn't report what it received (this happens when
using cfg80211_inform_bss[_width]())
4) both probe response and beacon data has been received
Unfortunately, in the userspace API, a few things weren't there:
a) there was no way to differentiate cases 1) and 4) above
without comparing the data of the IEs
b) the TSF was always from the last frame, instead of being
exposed for beacon/probe response separately like IEs
Fix this by
i) exporting a new flag attribute that indicates whether or
not probe response data has been received - this addresses (a)
ii) exporting a BEACON_TSF attribute that holds the beacon's TSF
if a beacon has been received
iii) not exporting the beacon attributes in case (3) above as that
would just lead userspace into thinking the data actually came
from a beacon when that isn't clear
To implement this, track inside the IEs struct whether or not it
(definitely) came from a beacon.
Reported-by: William Seto
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may need information about the expected throughput
towards a given peer.
This value is supposed to consider the size overhead
generated by the 802.11 header.
This value is exported in kbps through the get_station() API
by including it into the station_info object.
Moreover, it is sent to user space when replying to the
nl80211 GET_STATION command.
This information will be useful to the batman-adv module
which will use it for its new metric computation.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the type of NL80211_ATTR_CSA_C_OFF_BEACON and
NL80211_ATTR_CSA_C_OFF_PRESP to be NLA_BINARY which allows
userspace to use beacons and probe responses with
multiple CSA counters.
This isn't breaking the API since userspace can
continue to use nla_put_u16 for this attributes, which
is equivalent to a single element u16 array.
In addition advertise max number of supported CSA counters.
This is needed when using CSA and eCSA IEs together.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_ATTR_CSA_C_OFFSETS_TX which holds an array
of offsets to the CSA counters which should be updated
when sending a management frames with NL80211_CMD_FRAME.
This API should be used by the drivers that wish to keep the
CSA counter updated in probe responses, but do not implement
probe response offloading and so, do not use
ieee80211_proberesp_get function.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the moment, the ath9k/ath10k DFS module only supports detecting ETSI
radar patterns.
Add a bitmap in the interface combinations, indicating which DFS regions
are supported by the detector. If unset, support for all regions is
assumed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Julan Hsu