Add support for PHY_INTERFACE_MODE_5GBASER mode within the Marvell CP110
common PHY driver.
This is currently only supported via SMC calls to TF-A. Legacy support
may be added later, if needed.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the format and add description for ops to fix the below warnings:
drivers/phy/marvell/phy-mvebu-cp110-utmi.c:94: warning: Function parameter or member 'syscon' not described in 'mvebu_cp110_utmi'
drivers/phy/marvell/phy-mvebu-cp110-utmi.c:94: warning: Function parameter or member 'ops' not described in 'mvebu_cp110_utmi'
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211116103951.34482-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Armada 3700 does not support RXAUI, XFI and neither SFI. Remove unused
macros for these unsupported modes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 9695375a3f ("phy: add A3700 COMPHY support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Comphy phy mode 0x3 is incorrectly named. It is not SGMII but rather
2500Base-X mode which runs at 3.125 Gbps speed.
Rename macro names and comments to 2500Base-X.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 9695375a3f ("phy: add A3700 COMPHY support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Comphy phy mode 0x3 is incorrectly named. It is not SGMII but rather
2500Base-X mode which runs at 3.125 Gbps speed.
Rename macro names and comments to 2500Base-X.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: eb6a1fcb53 ("phy: mvebu-cp110-comphy: Add SMC call support")
Fixes: c2afb2fef5 ("phy: mvebu-cp110-comphy: Rename the macro handling only Ethernet modes")
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: He Ying <heying24@huawei.com>
Link: https://lore.kernel.org/r/20210408090806.247325-1-heying24@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When USB and USB_COMMON are not enabled, phy-mvebu-cp110-utmi
suffers a build error due to a missing interface that is provided
by CONFIG_USB_COMMON, so make the driver depend on USB_COMMON.
ld: drivers/phy/marvell/phy-mvebu-cp110-utmi.o: in function `mvebu_cp110_utmi_phy_probe':
phy-mvebu-cp110-utmi.c:(.text+0x152): undefined reference to `of_usb_get_dr_mode_by_phy'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Link: https://lore.kernel.org/r/20210401210045.23525-1-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of ARMADA375_USBCLUSTER_PHY
to MACH_ARMADA_375, and ask the user in case of compile-testing.
Fixes: eee47538ec ("phy: add support for USB cluster on the Armada 375 SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210208150252.424706-1-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for Marvell CP110 UTMI PHY driver allowing the USB2
port configuration independently from the boot loader setup.
The CP110/CP115 dies have 2 UTMI PHYs that could be connected
to two USB host controllers or to single USB device controller.
Since there is only one USB device controller on die, only one
of the UTMI PHYs could work in USB device mode.
The CONFIG_PHY_MVEBU_CP110_UTMI should be enabled for usage of
this driver.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20210307163343.25684-2-kostap@marvell.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add PHY driver for the HSICs found on Marvell MMP3 SoC. The driver is
rather straightforward -- the PHY essentially just needs to be enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20200925235828.228626-4-lkundrak@v3.sk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver ->power_on and ->power_off callbacks leaks internal SMCC firmware
return codes to phy caller. This patch converts SMCC error codes to
standard linux errno codes. Include file linux/arm-smccc.h already provides
defines for SMCC error codes, so use them instead of custom driver defines.
Note that return value is signed 32bit, but stored in unsigned long type
with zero padding.
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://lore.kernel.org/r/20200902144344.16684-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The mvneta hardware appears to lock up in various random ways when
repeatedly switching speeds between 1G and 2.5G, which involves
reprogramming the COMPHY. It is not entirely clear why this happens,
but best guess is that reprogramming the COMPHY glitches mvneta clocks
causing the hardware to fail. It seems that rebooting resolves the
failure, but not down/up cycling the interface alone.
Various other approaches have been tried, such as trying to cleanly
power down the COMPHY and then take it back through the power up
initialisation, but this does not seem to help.
It was finally noticed that u-boot's last step when configuring a
COMPHY for "SGMII" mode was to poke at a register described as
"GBE_CONFIGURATION_REG", which is undocumented in any external
documentation. All that we have is the fact that u-boot sets a bit
corresponding to the "SGMII" lane at the end of COMPHY initialisation.
Experimentation shows that if we clear this bit prior to changing the
speed, and then set it afterwards, mvneta does not suffer this problem
on the SolidRun Clearfog when switching speeds between 1G and 2.5G.
This problem was found while script-testing phylink.
This fix also requires the corresponding change to DT to be effective.
See "ARM: dts: armada-38x: fix NETA lockup when repeatedly switching
speeds".
Fixes: 14dc100b44 ("phy: armada38x: add common phy support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1jxtRj-0003Tz-CG@rmk-PC.armlinux.org.uk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We get warning with W=1 build:
drivers/phy/marvell/phy-mvebu-a3700-utmi.c:84: warning: Function
parameter or member 'usb_misc' not described in 'mvebu_a3700_utmi'
Fix that by correcting the typo usb_mis
Link: https://lore.kernel.org/r/20200708132809.265967-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
Some of the phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200103164710.4829-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch network drivers, phy drivers, and SFP/phylink over to use the
more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane
ethernet, which is 10GBASE-R with autonegotiation on top, which our
current usage on the affected platforms does not have.
The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia
PHY, which has a separate mode for 10GBASE-KR.
For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R
for compatibility with existing DT - this is the only network driver
at present that makes use of PHY_INTERFACE_MODE_10GKR.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl3pORkPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3FK0P/0EG4lK+il7nE3pd9yIGUjlcYuumIjoxvyC9
9ef202POJLIO3yMlsNyGFR+aOknFO/GtGvDkDFhTtlsGCL40tVzVsyo7ZQo+8mXD
abr+H74NmRXImc+SISYR8X1CD6vEi3oi/no1y5dRzknlBikfsdSLKXJSMYBJ2A6t
DNLwu0h1IZhPk7XQQsxaElG/a9HN8eueMdP20J1IlhOh0GiOwm+rbsLSZNbA/W9m
53XhFs3Ag39SDE0BfXsS+XOWTE7FheZsZk2XQrOwYm9PnxjpIWH7FE2sYsk6uUIc
Pa1b6wB5zlRnxvVHP0m3GXhbTUJDYDK3oybHffI4Mzd0cyZQHC92LhUXFrlTxkaf
6kyhJOTdd5KMlZ2LS7jkwLqb30ieXBPKAREjdbRt6hpvu5P6G+bZQphTEeNAZC61
XnX8mQ/XeoHdoGY5MvS8ht6a1qDF29ebA0/02seicThGK6tS9Qsju6Zo0sg9H1NH
weK6jDuzLq5jpv/LB1apigrDSx+zddRzrwkwy85hR5aWOQhG0xjOoFBProbTS0to
wR46zCEkbGZv4uc0gRuIdp0NR/lguqgDWPeoLluoTqmcpKS6N3RyxD0bWzlvgDFA
fpYxVNKavHneWjfZ7U5RbYXD6jycJcuLaCOs16nrtUbMgJ9pqclLIaZXn7ZTRIuT
RW6NgfZV
=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add PHY driver for the USB2 PHY found on Marvell MMP3 SoC.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The documentation for Marvell's cp110 phy refers to these
registers/register regions as DTL control, DTL frequency loop enable,
etc. This patch aligns the relevant code for these accordingly.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Marvell's cp110 phy supports RXAUI on lanes 2, 3, 4, and 5 when
connected to port zero. When used in this mode, lanes operate in pairs
of two (2 and 3, 4 and 5).
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now that all COMPHY modes are supported by the driver, update the
comment stating that mvebu_comphy_power_off() should be called for
each lane. This is still wrong because for compatibility reasons, it
might break users running an old firmware (the driver only uses SMC
calls for SATA, USB and PCIe configuration, there is no code in Linux
to fallback on in these cases.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add PCIe support by filling the COMPHY modes table.
Also add a new macro to generate the right value for the firmware
depending on the width (PCI x1, x2, x4, etc). The width will be passed
by the core as the "submode" argument of the ->set_mode() callback. If
this argument is zero, default to x1 mode.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Before adding more logic, simplify a bit the writing of the
mvebu_comphy_get_mode() helper by using a pointer instead of
referencing a configuration with the entire table name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the corresponding entries in the COMPHY modes table.
SATA support does not need any additional care.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add USB3 host/device support by adding the right entries in the COMPHY
modes table. A new macro is created to instantiate a "generic" mode
ie. not an Ethernet one. This macro will be re-used when adding SATA
support.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The COMPHY can configure the SERDES lanes in several non-Ethernet
modes: SATA, USB3, PCIe. Drop the condition limiting the driver to
Ethernet modes only before adding support for more.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Before adding support for other PHY modes (not Ethernet ones), let's
rename the MVEBU_COMPHY_CONF macro to a more specific (and shorter)
appellation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for RXAUI mode by adding an entry in the COMPHY modes list.
There is no user for this mode yet so we can enforce an up-to-date
firmware and return an error otherwise without breaking anywone.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently, the driver supports setting lanes to 1000BASEX, 2500BASEX,
10GKR. Complete the COMPHY modes list by adding two (already
supported) cases for lane 4.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Keep the exact same list of supported configurations but first try to
use the firmware's implementation. If it fails, try the legacy method:
Linux implementation.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Explicitly set the lane submode (enum) to a known invalid value.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There is no public clock tree that implies such dependencies between
the MG/MG-core/AXI clocks and the COMPHY IP but accessing the COMPHY
registers while one of the three clocks are disabled stalls the CPU.
This happens if, for instance, the COMPHY driver probe is deferred
(eg. the USB Vbus regulator driver is not yet visible). The MVPP2
driver which also needs these clocks (among others) will
prepare/enable the clocks, then be deferred, and disable/unprepare
them. Next COMPHY lane to be configured would produce an infinite
stall.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PHY configuration has been implemented in the firmware and accessed
through SMC calls. In the past, it worked magically if the bootloader
was correctly doing the initializations.
With up-to-date bindings, the kernel will need a recent firmware in
order to do the initializations himself (we assume people must update
their firmware along with their kernel).
People might not understand why IPs that were working correctly before
stopped to be probed suddendly. In this case, let's advise the users
to update their firmware with a visual warning.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return in two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return in two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates (you will
have a merge issue with Kconfig and Makefile), xhci updates, and typec
additions. Also included in here are a lot of small cleanups and fixes
and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+hsw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynfNwCgqKKg+MxJ9pFjrwfWYOrbk+BBe2UAn2Elp4ia
8FTdneQfN2J8Hhc6KGXE
=Kx9I
-----END PGP SIGNATURE-----
Merge tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates, xhci
updates, and typec additions. Also included in here are a lot of small
cleanups and fixes and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
wusb: Remove unnecessary static function ckhdid_printf
usb: core: make default autosuspend delay configurable
usb: core: Fix typo in description of "authorized_default"
usb: chipidea: Refactor USB PHY selection and keep a single PHY
usb: chipidea: Grab the (legacy) USB PHY by phandle first
usb: chipidea: imx: set power polarity
dt-bindings: usb: ci-hdrc-usb2: add property power-active-high
usb: chipidea: imx: remove unused header files
usb: chipidea: tegra: Fix missed ci_hdrc_remove_device()
usb: core: add option of only authorizing internal devices
usb: typec: tps6598x: handle block writes separately with plain-I2C adapters
usb: xhci: Fix for Enabling USB ROLE SWITCH QUIRK on INTEL_SUNRISEPOINT_LP_XHCI
usb: xhci: fix build warning - missing prototype
usb: xhci: dbc: Fixing typo error.
usb: xhci: remove unused member 'parent' in xhci_regset struct
xhci: tegra: Prevent error pointer dereference
USB: serial: option: add Telit ME910 ECM composition
usb: core: Replace hardcoded check with inline function from usb.h
usb: core: skip interfaces disabled in devicetree
usb: typec: mux: remove redundant check on variable match
...
Add support for the Armada 38x common phy to allow us to change the
speed of the Ethernet serdes lane. This driver only supports
manipulation of the speed, it does not support configuration of the
common phy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell Armada 3700 SoC has two USB controllers, each of them being
wired to an internal UTMI PHY. Add a driver to control them.
Igal Liberman worked on supporting the PHY, I took the while 'register
configuration' from his work and rewrote almost entirely the
driver/bindings around it.
Co-developed-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a driver to support COMPHY, a hardware block providing shared
serdes PHYs on Marvell Armada 3700. This driver uses SMC calls and
rely on having an up-to-date firmware.
SATA, PCie and USB3 host mode have been tested successfully with an
ESPRESSObin. (HS)SGMII mode cannot be tested with this platform.
Evan worked on the original driver structure and Grzegorz on the SMC
calls rework. The structure of this driver has been copied from
Antoine Tenart work on CP110 COMPHY driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Co-developed-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Evan Wang <xswang@marvell.com>
Co-developed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Jakub Kicinski