Clean up the stale DBUG_ON checks and add a couple new ones.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the bte copy fails, the attempt to retrieve payloads merely returns a
null pointer deref and not NULL as was expected.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clearing of the msg->flags needs a barrier between it and the notify
of the channel threads that the messages are cleaned and ready for use.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
with current kernels, tulip 21142 ethernet controllers fail to connect
to a 10Mbps only (i.e. without negotiation-partner) network. It used
to work in 2.4 kernels. Fix that. Tested on a 21142 Rev 0x11.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 0f0ca340e5 ("phy: power
management support") caused a regression in the gianfar driver.
Now phylib turns off PHY power during suspend, and thus WOL
doesn't work anymore.
This patch workarounds the issue by enabling wakeup in the MDIO
device, i.e. just restores the old behaviour for the gianfar
driver. Note that this way all PHYs on a given MDIO bus won't
be turned off during suspend, which isn't good from the power
saving point of view.
A proper, per netdevice wakeup management support will need
a bit reworked phylib suspend/resume logic.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc9420 performs an interrupt signalling test when the interface is
brought up. The current code mistakenly sets its test flag to false
AFTER enabling the software interrupt source, making failure quite
likely.
This patch changes the code to set the test flag BEFORE enabling
interrupts. I've also removed an smp_wmb because the following spinlock
provides an implicit memory barrier.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx". For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Toralf Förster and Randy Dunlap.
- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html
- http://lkml.org/lkml/2009/1/29/279
The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.
These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak identified by Rusty Russell during LCA09 by
kfree'ing the lg object instead of just clearing it when the
launcher closes.
Signed-off-by: Mark Wallis <mwallis@serialmonkey.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.
This was reduced in commit 32ec803348
("netxen: reduce memory footprint").
Raising jumbo ring size from 512 to 1024, adds ~4MB per port, but
there's still big saving because of original patch (~20MB per port).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath5k_config updates the software context without taking sc->lock.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes memcpy to NULL address when the ucode DMA allocation failure.
This is a fix to bug
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1861
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After reports of poor performance, a review of the latest vendor driver
(rtl8187_linux_26.1025.0328.2007) for RTL8187L devices was undertaken.
A difference was found in the code used to index the OFDM power tables. When
the Linux driver was changed, my unit works at a much greater range than
before. I think this fixes Bugzilla #12380 and has been tested by at least
two other users.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Martín Ernesto Barreyro <barreyromartin@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
as per https://bugs.launchpad.net/bugs/294391. These got one sample of
each iPod generation going. However there still occurred I/O stalls
with the 3rd generation iPod which remain undiagnosed at the time of
this writing.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
According to https://bugs.launchpad.net/bugs/294391
- 3rd generation iPods need the "fix capacity" workaround after all
(apparently they crash after the last sector was accessed),
- 2nd generation iPods need the "128 kB maximum request size"
workaround.
Alas both iPod generations feature the same model ID in the config ROM,
hence we can only define a shared quirks list entry for them. Luckily
the fix capacity workaround did not show a negative effect in Jarod's
tests with 2nd gen. iPod.
A side note: Apple computers in target mode (or at least an x86 Mac
mini) don't have firmware_version and model_id, hence none of the iPod
quirks list entries is active for them.
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
1: make "target_kb" only accept and produce a memory size in kilobytes.
2: add a second "target" file which produces output in bytes, and will accept
memparse input (scaled bytes)
This fixes the rather irritating problem that writing the same value
read back into target_kb would end up shrinking the domain by a factor
of 1024, with generally bad results.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Cc: "dan.magenheimer@oracle.com" <dan.magenheimer@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Resetting the streaming flag on disconnection prevented the URBs to be freed
when streaming was active.
Also, USBs cannot be killed after disconnection (oops in [usbcore] unlink1).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trace: (Provided by Douglas)
BUG: sleeping function called from invalid context at drivers/usb/core/urb.c:558
in_atomic():0, irqs_disabled():1
Pid: 4918, comm: sox Not tainted 2.6.27.5 #1
[<c04246d8>] __might_sleep+0xc6/0xcb
[<c058c8b0>] usb_kill_urb+0x1a/0xd8
[<c0488e68>] ? __kmalloc+0x9b/0xfc
[<c0488e85>] ? __kmalloc+0xb8/0xfc
[<c058cd5a>] ? usb_alloc_urb+0xf/0x31
[<f8dd638c>] em28xx_isoc_audio_deinit+0x2f/0x6c [em28xx_alsa]
[<f8dd6573>] em28xx_cmd+0x1aa/0x1c5 [em28xx_alsa]
[<f8dd65e1>] snd_em28xx_capture_trigger+0x53/0x68 [em28xx_alsa]
[<f8aa8674>] snd_pcm_do_start+0x1c/0x23 [snd_pcm]
[<f8aa85d7>] snd_pcm_action_single+0x25/0x4b [snd_pcm]
[<f8aa9833>] snd_pcm_action+0x6a/0x76 [snd_pcm]
[<f8aa98f5>] snd_pcm_start+0x14/0x16 [snd_pcm]
[<f8aae10e>] snd_pcm_lib_read1+0x66/0x273 [snd_pcm]
[<f8aac5a3>] ? snd_pcm_kernel_ioctl+0x46/0x5f [snd_pcm]
[<f8aae4a7>] snd_pcm_lib_read+0xbf/0xcd [snd_pcm]
[<f8aad774>] ? snd_pcm_lib_read_transfer+0x0/0xaf [snd_pcm]
[<f89feeb6>] snd_pcm_oss_read3+0x99/0xdc [snd_pcm_oss]
[<f89fef9c>] snd_pcm_oss_read2+0xa3/0xbf [snd_pcm_oss]
[<c064169d>] ? _cond_resched+0x8/0x32
[<f89ff0be>] snd_pcm_oss_read+0x106/0x150 [snd_pcm_oss]
[<f89fefb8>] ? snd_pcm_oss_read+0x0/0x150 [snd_pcm_oss]
[<c048c6e2>] vfs_read+0x81/0xdc
[<c048c7d6>] sys_read+0x3b/0x60
[<c04039bf>] sysenter_do_call+0x12/0x34
=======================
The culprit in the trace is snd_pcm_action() which invokes a spin lock
which disables pre-emption which disables an IRQ which causes the
__might_sleep() function to fail the irqs_disabled() test. Since
pre-emption is enabled then it is safe to de-allocate the memory if
you first unlink each URB. In this instance you are safe since
pre-emption is disabled. If pre-emption and irqs are not disabled then
call usb_kill_urb(), else call usb_unlink_urb().
Thanks to Douglas for tracking down this bug originally!!!
[dougsland@redhat.com: Fixed codyingstyle]
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move radio->muted and radio->stereo in section where radio mutex is
locked to avoid possible race condition problems or access to memory.
Thanks to David Ellingsworth <david@identd.dyndns.org> for pointing to
this weak place in driver.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These days TUNER_SET_CONFIG is broadcast to the other i2c devices
and that triggers a fw load on the cx25840. Ignore this command
since cx25840 isn't a tuner and you really do not want to load
the firmware that early.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
First control messages to the stick timeouts very often due to probable
hw bug. Repeat first message few times if it fails as workaround.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bug causes 2nd FE MPEG TS buffer size to be zero and therefore no picture
when 2nd FE was enabled. Configure correct buffer size also for 2nd FE.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default case of the switch didn't unlock the mutex.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Revert a change made in change 9743 which resulted in a kernel panic in some
cases on shutdown of the audio stream.
First discovered when working on the Pinnacle 880e support, and later
reproduced by a user on the mailing list with the HVR-900 as well.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for KWorld 330U Board
Many thanks to Devin and Mauro!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for KWorld 330U AC97
Many thanks to Devin and Mauro again!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the conversion to v4l2_subdev one bit of code was accidentally dropped:
on receiving the first command the driver has to load the fw. A new init()
command was introduced to do that explicitly for bridge drivers that are
converted to use v4l2_subdev, but old drivers that are not yet converted
no longer worked.
This patch fixes this regression for these old drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VIDIOC_QUERYCTRL command needs to actually do a queryctrl, not a
querymenu. Similarly, the VIDIOC_QUERYMENU command needs to actually
do a querymenu not a queryctrl.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch adds support for a new version of the
Terratec Cinergy DT USB XS Diversity Dual DVB-T TV tuner stick.
The USB ID of the new stick is 0ccd:0081.
The hardware of the stick has changed, when compared to the first version of
this stick, but it still uses quite standard components, so that only minor
changes are needed to the sources.
The patch has been successfully tested with hotplugging the device and then
2 x tzap and 2 x mplayer, to watch two different TV programs simultaneously.
The stick works with both, the old and new firmwares:
- dvb-usb-dib0700-1.10.fw and
- dvb-usb-dib0700-1.20.fw
Signed-off-by: Nicolas Fournier <nicolasfournier@yahoo.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some em28xx devices use the PCM IN AC 97 PIN for digital audio. However,
currently, the PCM IN selection is not set by the driver. This patch allows
specifying the PCM IN expected output, via board description table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zoran driver does a module_get/put of THIS_MODULE on device open/close.
This isn't necessary as the kernel does this automatically.
Clean up the failure path of zoran_open() somewhat.
Make the dprintk()s on open/close a higher debug level and make the user
count printed take the current open/close into account.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver should only use the kernel mapped io address, zr36057_mem, and
not the PCI bus address, zr36057_adr. Since the latter is only printed out
once, there is no need to save it in the driver data structure.
There was some old code that looked like it was for the Alpha architecture
which would use the PCI bus address. It probably no longer applies to
modern kernels.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using custom code, just let the device layer look it up for us
from the pci device table. This requires extending the pci device table to
list each known card, plus a catch-all entry for the cards that don't have
sub-system vendor/device data.
Improve some of the info and error messages too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver was keeping a global array with an entry for each zoran device
probed. It was a leftover from when the driver didn't dynamically allocate
the driver data for each device.
There was only one use left, in the video device's ->open() method, looking
up the struct zoran for the opened device from the minor number. This can
be done better with video_get_drvdata().
Since zoran_num is now only used in the pci driver's ->probe() method, it
doesn't need to be an atomic_t and be static. There is a race if multiple
zoran cards could be probed at the same time, but currently the probe
method for a given driver is single threaded.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When initializing a module parameter that is a per-card array, use
"{ [0 ... (BUZ_MAX-1)] = -1 }" instead of "{ -1, -1, -1, -1 }". This way
all of the entries will be correctly set to -1 if someone changes BUZ_MAX
to a value other than 4.
Adjust some of the parameter help text too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When enabling a shared IRQ line, then saa7134_irq handler could be invoked
before the driver had completely set up internal structures, due to a shared
interrupt line firing. Clear the saa7134 interrupt status reg, before
requesting the irq line, so that stale IRQ status isn't processed before the
internal structures are set up.
Marcin Slusarz recently brought this Oops to the attention of the v4l-dvb
lists and provided an initial analysis by investigating reports found here:
http://kerneloops.org/guilty.php?guilty=mute_input_7133&version=2.6.27-release&start=1802240&end=1835007&class=oops
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Analog support for HVR-1250 has not been completed, but does exist for
the HVR-1800.
Since both cards use the same driver, it tries to create the analog
dev for both devices, which is not possible.
This causes a NULL error to show up in video_open and mpeg_open.
-Mark
Iterations through the cx23885_devlist must check for NULL
pointers as some supported devices only have DVB support at the moment.
Mark Jenks encoutered an Oops in a system with both an HVR-1250 and HVR-1800
installed.
-Andy
Reported-by: Mark Jenks <mjenks1968@gmail.com>
Tested-by: Mark Jenks <mjenks1968@gmail.com>
Signed-off-by: Mark Jenks <mjenks1968@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register 0x2d has to be set differently in the saa7129 compared to the
saa7127. This was not done correctly, so S-Video was broken in certain
circumstances.
This fixes a regression introduced in 2.6.28.
Signed-off-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a really old and crufty driver that wasn't using the long
established pci driver framework.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
[mchehab@redhat.com: Cleaned up a few CodingStyle issues]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If Hauppauge eeprom is corrupted, the driver returns tuner = 0, instead
of TUNER_ABSENT.
This makes the drivers to initialize tuner, instead of handling the
manual parameter.
Since the tuner core rejects that a tuner to have their type changed,
this breaks the manual tuner override.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 60b4bde48b removed an unused
struct on zoran driver, when compiled with "Y".
However, as pointed by Jean Delvare <khali@linux-fr.org>, this is
neeeded when the driver is compiled as a module, since udev relies on it
to auto-load the module.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Concurrent access to a single DVB CA 50221 interface slot is generally
discouraged. The underlying drivers (budget-av, budget-ci) do not implement
proper locking and thus two transactions could (and do) interfere with on
another.
This fixes the following problems seen by others and myself:
- sudden i/o errors when writing to the ci device which usually would
result in an undefined state of the hw and require a software restart
- errors about the CAM trying to send a buffer larger than the agreed size
usually also resulting in an undefined state of the hw
Due the to design of the DVB CA 50221 driver, implementing the locks in the
underlying drivers would not be enough and still leave some race conditions,
even though they were harder to trigger.
Signed-off-by: Matthias Dahl <devel@mortal-soul.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
to avoid:
| tvp514x 0-005c: No platform data
| !!<3>tvp514x 0-005d: No platform data
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Randy Dunlap <randy.dunlap@oracle.com> wrote:
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c: In function 'cx88_call_i2c_clients':
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:122: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:123: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:127: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:128: error: 'struct cx88_core' has no member named 'gate_ctrl'
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC specification release number is a binary-coded decimal number, print
it as such.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces support for dvb-t for the following dibcom based card:
Terratec Cinergy T Express (USB-ID: 0ccd:0062)
Signed-off-by: Yusuf Altin <yusuf.altin@t-online.de>
Signed-off-by: Albert Comerma <albert.comerma@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx were trying to access the third input entry, even for boards that
don't support it.
This patch reviews the input mux selection fixing this bug and a few
other troubles, like not validating the input on one userspace ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many people get it wrong and add device IDs into hid_blacklist instead
of hid_ignore_list. Let's put a little comment in place.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_ignore_list additions for the Antec-branded SoundGraph iMon VFD and LCD
devices (0x15c2:0x0044 and 0x0045).
These devices are driven by lirc.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The logic for testing for disconnection is reversed in an ioctl leading
to false reports of disconnection.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Report descriptor fixup for MS 1028 receiver changes also values for
Keyboard and Consumer, which incorrectly trims the range, causing correct
events being thrown away before passing to userspace.
We need to keep the GenDesk usage fixup though, as it reports totally bogus
values about axis.
Reported-by: Lucas Gadani <lgadani@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is true that BM_RLD needs to be set to enable
bus master activity to wake an older chipset (eg PIIX4) from C3.
This is contrary to the erroneous wording the ACPI 2.0, 3.0
specifications that suggests that BM_RLD is an indicator
rather than a control bit.
ACPI 1.0's correct wording should be restored in ACPI 4.0:
http://www.acpica.org/bugzilla/show_bug.cgi?id=689
But the kernel should not have to clear BM_RLD
when entering a non C3-type state just to set
it again when entering a C3-type C-state.
We should be able to set BM_RLD at boot time
and leave it alone -- removing the overhead of
accessing this IO register from the idle entry path.
Signed-off-by: Len Brown <len.brown@intel.com>
Fix function parameter name in kernel-doc:
Warning(linux-next-20090120//drivers/base/core.c:1289): No description found for parameter 'dev'
Warning(linux-next-20090120//drivers/base/core.c:1289): Excess function parameter 'root' description in 'root_device_unregister'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On m68k:
drivers/staging/agnx/agnx.h: In function 'agnx_read32':
drivers/staging/agnx/agnx.h:10: error: implicit declaration of function 'ioread32'
drivers/staging/agnx/agnx.h: In function 'agnx_write32':
drivers/staging/agnx/agnx.h:15: error: implicit declaration of function 'iowrite32'
drivers/staging/agnx/sta.c: In function 'get_sta_power':
drivers/staging/agnx/sta.c:94: error: implicit declaration of function 'memcpy_fromio'
drivers/staging/agnx/sta.c: In function 'set_sta_power':
drivers/staging/agnx/sta.c:103: error: implicit declaration of function 'memcpy_toio'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Compile tested.
task_struct->signal is not protected by RCU, the code is bogus.
Change the code to take ->siglock to pin ->signal.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Brian Swetland <swetland@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ktime_t isn't ment to directly access on all arches, so use the proper
conversion functions instead to figure out what time is remaining.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Mike Lockwood <lockwood@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Meilhaus drivers do not like being built into the kernel right now,
so force them to be a module.
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
comedi doesn't like being built into the kernel right now, so force it
to be a module.
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
who also provided a first version of the fix.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
1394-2008 clause 16.3.4.1 (1394b-2002 clause 16.3.1.1) defines tighter
limits than 1394-2008 clause 6.2.2.3 (1394a-2000 clause 6.2.2.3).
Our previously too large limit doesn't matter though if the controller
reports its max_receive correctly.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This makes sbp2 behave more like firewire-sbp2 which reports 0xff000000
as immediate value if there are no unit directory entries for model_id
or firmware_revision.
It does not reduce matches with the currently existing quirks table; the
only zero entry there is for a device which actually does have a zero
model_id. It only changes how model_id and firmware_revision are logged
if they are missing.
Other functionally unrelated changes: The model_id member of quirks
list entries is renamed to model; the value (but not the effect) of
SBP2_ROM_VALUE_WILDCARD is changed. Now this part of the source is
identical with firewire-sbp2 for easier maintenance.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
1394-2008 clause 16.3.4.1 (1394b-2002 clause 16.3.1.1) defines tighter
limits than 1394-2008 clause 6.2.2.3 (1394a-2000 clause 6.2.2.3).
Our previously too large limit doesn't matter though if the controller
reports its max_receive correctly.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The hard-wired configuration of the top speed (until now S800) was
unnecessary, remove it.
If the local link layer controller supports S1600 or S3200, we now
assume this speed for all present 1394b PHYs (except if they are
behind 1394a repeaters) until nodemgr figured out the actual speed
while fetching the config ROM.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
PM1a_STS and PM1b_STS are twins that get OR'd together
on reads, and all writes are repeated to both.
The fields in PM1x_STS are single bits only,
there are no multi-bit fields.
So it is not necessary to lock PM1x_STS reads against
writes because it is impossible to read an intermediate
value of a single bit. It will either be 0 or 1,
even if a write is in progress during the read.
Reads are asynchronous to writes no matter if a lock
is used or not.
Signed-off-by: Len Brown <len.brown@intel.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
powerpc/pseries: Correct VIO bus accounting problem in CMO env.
powerpc: More printing warning fixes for the l64 to ll64 conversion
powerpc: Remove arch/ppc cruft from Kconfig
powerpc: Printing fix for l64 to ll64 conversion: phyp_dump.c
powerpc/embedded6xx: Update defconfigs
powerpc/8xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/mpc8313erdb: fix kernel panic because mdio device is not probed
powerpc/4xx: Update multi-board PowerPC 4xx defconfigs
powerpc/44x: Update PowerPC 44x defconfigs
powerpc/40x: Update PowerPC 40x defconfigs
powerpc/85xx: Fix typo in mpc8572ds dts
powerpc/44x: Warp patches for the new NDFC driver
powerpc/4xx: DTS: Add Add'l SDRAM0 Compatible and Interrupt Info
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 5329 ColdFire periphal addressing
uclinux: add process name to allocation error message
m68knommu: correct the mii calculations for 532x ColdFire FEC
m68knommu: add ColdFire M532x to the FEC configuration options
m68knommu: fix syscall restarting
m68knommu: remove the obsolete and long unused comempci chip support
m68knommu: remove the no longer used PCI support option
m68knommu: remove obsolete and unused eLIA board
m68knommu: set NO_DMA
m68knommu: fix cache flushing for the 527x ColdFire processors
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
m68knommu: use one exist from execption
Schedule a vblank signal, kill the process, and we'll go walking over freed
memory. Given that no open-source userland exists using this, nor have I
ever heard of a consumer, just let this code die.
Signed-off-by: Eric Anholt <eric@anholt.net>
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Further to 483a2b3a31, also fix:
drivers/net/arm/etherh.c:649: error: 'eth_set_mac_addr' undeclared here (not in a function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A nasty bug was found where an MTU change (or anything else that caused a
reset) could race with the interrupt code. The interrupt code was entered
by a shared interrupt during the MTU change.
This change prevents the interrupt code from running while the driver is in
the middle of its reset path.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
USB: Driver for Freescale QUICC Engine USB Host Controller
USB: option: add QUANTA HSDPA Data Card device ids
USB: storage: Add another unusual_dev for off-by-one bug
USB: unusual_dev: usb-storage needs to ignore a device
USB: GADGET: fix !x & y
USB: new id for ti_usb_3410_5052 driver
USB: cdc-acm: Add another conexant modem to the quirks
USB: 'option' driver - onda device MT503HS has wrong id
USB: Remove ZTE modem from unusual_devices
USB: storage: support of Dane-Elec MediaTouch USB device
USB: usbmon: Implement compat_ioctl
USB: add kernel-doc for wusb_dev in struct usb_device
USB: ftdi_sio driver support of bar code scanner from Diebold
USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
USB: cp2101 device
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
USB: remove vernier labpro from ldusb
USB: CDC-ACM quirk for MTK GPS
USB: cdc-acm: support some gps data loggers
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
...
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.
Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.
At this time usb_modeswitch does not work with this device.
Reported-by: The Solutor <thesolutor@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
! has a higher precedence than &
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another Conexant, another device with the same quirk
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).
This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: Marcel Sebek <sebek64@post.cz>
Acked-by: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.
Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.
Signed-off-by: Jean-Baptiste Onofre <jb@nanthrax.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0
It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.
This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: Mhayk Whandson <eu@mhayk.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: Robie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,
PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c
From: Tomasz K <eros81@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?
output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):
before patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)
after patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0
Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Labpro device is in both ldusb and vstusb device tables.
Should only be a vstusb device.
Signed-off-by: stephen ware <stephen.ware@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.
I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: Andrew Lunn, <andrew@lunn.ch>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.
From: James A. Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.
This patch fixes this issue.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies. This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initializes the actual_len field to 0 before every DMA transaction.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:
drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h:
No such file or directory
drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h:
No such file or directory
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes insert module failure as free_irq() was not
done in previous rmmod.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trying once more to get this merged. The original was submitted
for 2.6.27-rc2 or so, and never got correctly merged. Neither
were any of the numerous subsequent resends. Sigh.
CC drivers/usb/musb/davinci.o
drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory
drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory
drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory
drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode'
drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> > drivers/built-in.o: In function `ohci_omap_init':
> > hid-quirks.c:(.text+0x6c608): undefined reference to `otg_get_transceiver'
> > drivers/built-in.o: In function `omap_udc_probe':
> > hid-quirks.c:(.init.text+0x34c0): undefined reference to `otg_get_transceiver'
> > hid-quirks.c:(.init.text+0x3d40): undefined reference to `otg_put_transceiver'
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1198) fixes a conceptual bug: Somewhere along the line
we managed to confuse USB class devices with USB char devices. As a
result, the code to send a disconnect signal to userspace would not be
built if both CONFIG_USB_DEVICE_CLASS and CONFIG_USB_DEVICEFS were
disabled.
The usb_fs_classdev_common_remove() routine has been renamed to
usbdev_remove() and it is now called whenever any USB device is
removed, not just when a class device is unregistered. The notifier
registration and unregistration calls are no longer conditionally
compiled. And since the common removal code will always be called as
part of the char device interface, there's no need to call it again as
part of the usbfs interface; thus the invocation of
usb_fs_classdev_common_remove() has been taken out of
usbfs_remove_device().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Alon Bar-Lev <alon.barlev@gmail.com>
Tested-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: stable <stable@kernel.org>
Commit a0d4922da2
(USB: fix up suspend and resume for PCI host controllers) attempted
to fix the suspend-resume of PCI USB controllers, but unfortunately
it did that incorrectly and interrupts are left enabled by the USB
controllers' ->suspend_late() callback as a result. This leads to
serious problems during suspend which are very difficult to debug.
Fix the issue by removing the ->suspend_late() callback of PCI
USB controllers and moving the code from there to the ->suspend()
callback executed with interrupts enabled. Additionally, make
the ->resume() callback of PCI USB controllers execute
pci_enable_wake(dev, PCI_D0, false) to disable wake-up from the
full power state (PCI_D0).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: "Jeff Chua" <jeff.chua.linux@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Zdenek Kabelac" <zdenek.kabelac@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1199) changes the initial wakeup settings for PCI USB
host controllers. The controllers are marked as capable of waking the
system, but wakeup is not enabled by default.
It turns out that enabling wakeup for USB host controllers has a lot
of bad consequences. As the simplest example, if a USB mouse or
keyboard is unplugged immediately after the computer is put to sleep,
the unplug will cause the system to wake back up again! We are better
off marking them as wakeup-capable and leaving wakeup disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds an unusual devs entry for 2116:0320
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1200) finishes some fixes that were left incomplete by
an earlier patch.
Although nobody has addressed this issue in the past, it turns out
that we need to distinguish between two different modes of disabling
and enabling endpoints. In one mode only the data structures in
usbcore are affected, and in the other mode the host controller and
device hardware states are affected as well.
The earlier patch added an extra argument to the routines in the
enable_endpoint pathways to reflect this difference. This patch adds
corresponding arguments to the disable_endpoint pathways. Without
this change, the endpoint toggle state can get out of sync between
the host and the device. The exact mechanism depends on the details
of the host controller (whether or not it stores its own copy of the
toggle values).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dan Streetman <ddstreet@ieee.org>
Tested-by: Dan Streetman <ddstreet@ieee.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the vendor/product ID of the fasttrax GPS evaluation kit from:
http://www.fastraxgps.com/products/evaluationtools/evaluationkit/
to the cp2101 module since this device is actually equipped with a
CP210x USB to serial bridge.
The vendor/product ID is: 0x10c4/0x826b.
Signed-off-by: Wolfgang Glas <wolfgang.glas@ev-i.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] ibmvfc: Fix DMA mapping leak on memory allocation failure
[SCSI] qla2xxx: Update version number to 8.03.00-k2.
[SCSI] qla2xxx: Add checks for a valid fcport in dev-loss-tmo/terminate_rport_io callbacks.
[SCSI] qla2xxx: Correct regression in DMA-mask setting prior to allocations.
[SCSI] qla2xxx: Correct descriptions in flash manipulation routines.
[SCSI] qla2xxx: Correct regression in EH abort handling.
[SCSI] qla2xxx: Correct endianness issue during flash manipulation.
[SCSI] qla2xxx: Correct MSI-X vector allocation for single queue mode.
[SCSI] qla2xxx: Modify firmware-load order precedence for ISP81XX parts.
[SCSI] qla2xxx: Always serialize mailbox command execution.
[SCSI] qla2xxx: Ensure RISC-interrupt-enabled consistency for IS_NOPOLLING_TYPE() ISPs.
[SCSI] qla2xxx: Simplify sector-mask calculation in preparation for larger flash parts.
[SCSI] qla2xxx: Fix memory leak in error path
[SCSI] qla4xxx: do not reuse session when connecting to different target port
[SCSI] libiscsi: fix iscsi pool leak
Some hardware exposes PCIE slots in such a way that they can be claimed
by either the acpiphp or pciehp driver. pciehp is the preferred driver
if the firmware allows the OS to claim control via the _OSC method so
should be loaded first - if it fails to bind (either due to a missing
_OSC method or the firmware refusing to hand off control) then we can
fall back to acpiphp or a vendor-specific driver.
This patch simply changes the link order to ensure that pciehp will be
initialised before acpiphp if both are statically built into the kernel.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For PCI devices, pci_bus_assign_resources() must be called to set up the
pci_device->resource array before pci_bus_add_devices() can be called, else
attempts to load drivers results in BAR collision errors where there are none.
This is not done in fakephp, so devices can be "unplugged" but scanning the
parent bus won't bring the devices back due to resource unallocation. Move the
pci_bus_add_device-calling logic into pci_rescan_bus and preface it with a call
to pci_bus_assign_resources so that we only have to (re)allocate resources once
per bus where a new device is found.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add an msi_mask() function which returns the correct bitmask for the
number of MSI interrupts you have. This fixes an undefined bug in
msi_capability_init().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_restore_standard_config() adds extra delay for PCI buses in
low power states (B2 or B3), but this is only correct for buses in
B2, because the buses in B3 are reset when they are put back into
B0. Thus we should wait for such buses to settle after the reset,
but it's not a good idea to wait that long (1.1 s) with interrupts
off.
On the other hand, we have never waited for buses in B2 and B3
during resume and it seems reasonable to go back to this well
tested behaviour.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Devices that have MSI-X enabled before suspend to RAM or hibernation
and that are in a low power state during resume will not be handled
correctly by pci_restore_standard_config(). Namely, it first calls
pci_restore_state() which calls pci_restore_msi_state(), which in turn
executes __pci_restore_msix_state() that accesses the device's memory
space to restore the contents of the MSI-X table. However, if the
device is in a low power state at this point, it's memory space is
not accessible.
The easiest way to fix this potential problem is to make
pci_restore_standard_config() call pci_restore_state() after
it has put the device into the full power state, D0. Fortunately,
all of this is done with interrupts off, so the change of ordering
should not cause any trouble.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Hibernation breaks on EeePC 701 as a result of attempting to put one
of its (driverless) devices into a low power state. Avoid that by
not attepmting to power manage driverless devices during hibernation.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If one of device drivers refuses to suspend by returning error code
from its ->suspend() callback, the devices that have already been
suspended are resumed by executing their drivers' ->resume()
callbacks. Some of these callbacks expect the device's
configuration space to be restored if the device has been put into
D3 before they are called. Unfortunately, this mechanism has been
broken by recent changes moving the restoration of config spaces
of some devices (most importantly, USB controllers and HDA Intel)
into the resume callbacks executed with interrupts off. Obviously,
these callbacks are not invoked in the suspend error path and, as a
result, the system cannot be successfully brought back into the
working state in case of a suspend error. The same thing happens
in the hibernation error path right before putting the system into
S4.
Similarly, the suspend testing facility associated with the
/sys/power/pm_test file is broken, because it uses the very same
mechanism that is used in the suspend and hibernation error paths.
Fix the breakage by making the PCI core restore the configuration
spaces of PCI devices that haven't been restored already before
pci_pm_resume() is called for those devices by the PM core.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'hibern_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
SATA PIIX: Blacklist system that spins off disks during ACPI power off
SATA Sil: Blacklist system that spins off disks during ACPI power off
SATA AHCI: Blacklist system that spins off disks during ACPI power off
SATA: Blacklisting of systems that spin off disks during ACPI power off
DMI: Introduce dmi_first_match to make the interface more flexible
Hibernation: Introduce system_entering_hibernation
This Patch add the device information for the
MIC-3620 8-port RS-232 cPCI card from Advantech Co. Ltd.
Signed-off-by: Michael Bramer <grisu@deb-support.de>
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function jsm_remove_one is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__tty_open could return (to userspace) holding the tty_mutex thanks to a
regression introduced by 4a2b5fddd5 ("Move
tty lookup/reopen to caller").
This was found by bisecting an fsfuzzer problem. Admittedly I have no
idea how it managed to tickle this 100% reliably, but it is clearly a
regression and when hit leaves the box in a completely unusable state.
This patch lets the fsfuzzer test complete every time.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a new ioctl UBI_IOCSETPROP to set properties
on a volume. Also add the first property:
UBI_PROP_DIRECT_WRITE, this property is used to set the
ability to use direct writes in userspace
Signed-off-by: Sidney Amani <seed@uffs.org>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP 2510p that uses the ata_piix driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP nx6325 that uses the sata_sil driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP nx6310 that uses the AHCI driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information. However, only the on-board controlles should
be blacklisted and their PCI slot numbers can be used for this
purpose. Unfortunately the existing interface for checking DMI
information of the system is not very convenient for this purpose,
because to use it, we would have to define special callback functions
or create a separate struct dmi_system_id table for each blacklisted
system.
To overcome this difficulty introduce a new function
dmi_first_match() returning a pointer to the first entry in an array
of struct dmi_system_id elements that matches the system DMI
information. Then, we can use this pointer to access the entry's
.driver_data field containing the additional information, such as
the PCI slot number, allowing us to do the desired blacklisting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver has been tested without the call to set_irq_type at this
point and occurs to work fine, so it should be safe to remove it.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I noticed (the hard way) that the mcf.c driver doesn't support the fractional precision register on the MCF5272. This makes the console dicey at 115200 baud and a system clock of 66.0 MHz. On the other hand, if your hardware is running at 66.666 MHz, it probably isn't a problem.
Patch submitted by John Adamson <jadamson@allen-organ.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
drivers/net/r6040.c:441: warning: unused variable 'pdev'
Signed-off-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this fix, virtio_net makes incorrect usage of scatterlists. It sets
the end of the scatterlist chain after the first element, despite the fact
that more entries come after it.
If you try to run dma_map_sg() on one of the scatterlists given to you by
add_buf(), you will get a null pointer oops.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Warn on deprecated binding model use
eeprom: More consistent symbol names
eeprom: Move 93cx6 eeprom driver to /drivers/misc/eeprom
spi: Move at25 (for SPI eeproms) to /drivers/misc/eeprom
i2c: Move old eeprom driver to /drivers/misc/eeprom
i2c: Move at24 to drivers/misc/eeprom
i2c: Quilt tree has moved
i2c: Delete many unused adapter IDs
i2c: Delete 10 unused driver IDs
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (92 commits)
gianfar: Revive VLAN support
vlan: Export symbols as non GPL symbols.
bnx2x: tx_has_work should not wait for FW
netxen: reduce memory footprint
netxen: fix vlan tso/checksum offload
net: Fix linux/if_frad.h's suitability for userspace.
net: Move config NET_NS to from net/Kconfig to init/Kconfig
isdn: Fix missing ifdef in isdn_ppp
networking: document "nc" in addition to "netcat" in netconsole.txt
e1000e: workaround hw errata
af_key: initialize xfrm encap_oa
virtio_net: Fix MAX_PACKET_LEN to support 802.1Q VLANs
lcs: fix compilation for !CONFIG_IP_MULTICAST
rtl8187: Add termination packet to prevent stall
iwlwifi: fix rs_get_rate WARN_ON()
p54usb: fix packet loss with first generation devices
sctp: Fix another socket race during accept/peeloff
sctp: Properly timestamp outgoing data chunks for rtx purposes
sctp: Correctly start rtx timer on new packet transmissions.
sctp: Fix crc32c calculations on big-endian arhes.
...
commit 77ecaf2d5a ("gianfar: Fix VLAN
HW feature related frame/buffer size calculation") wrongly removed
priv->vlgrp assignment, and now priv->vlgrp is always NULL.
This patch fixes the issue, plus fixes following sparse warning
introduced by the same commit:
gianfar.c:1406:13: warning: context imbalance in 'gfar_vlan_rx_register' - wrong count at exit
gfar_vlan_rx_register() checks for "if (old_grp == grp)" and tries
to return w/o dropping the lock.
According to net/8021q/vlan.c VLAN core issues rx_register() callback:
1. In register_vlan_dev() only on a newly created group;
2. In unregister_vlan_dev() only if the group becomes empty.
Thus the check in the gianfar driver isn't needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tx_has_work waited until all packets sent by the driver
are marked as completed by the FW. This is too greedy and it causes
the bnx2x_poll to spin in vain. The driver should only check that all
packets FW already completed are freed - only in unload flow the
driver should make sure that transmit queue is empty
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o reduce rx ring size from 8192 to 4096.
o cut down old huge lro buffers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o set netdev->vlan_features appropriately.
o fix tso descriptor initialization for vlan case.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch fixes a warning caused by a missing ifdef in
isdn_ppp.c. A function was defined, but never used if CONFIG_IPPP_FILTER
was not defined.
The warning was: 'get_filter' defined but not used
Patch is against 2.6.28.1
Signed-off-by: Daniele Venzano <venza@brownhat.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.
Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Update Kconfig text to specify this driver as I2C.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As drivers/i2c/chips is going to go away, move the driver to
drivers/misc/eeprom. Other eeprom drivers may be moved here later, too.
Update Kconfig text to specify this driver as I2C.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a hardware errata in some revisions of the 82574 that needs
to be worked around in the driver by setting a register bit at init.
If this bit is not set A0 versions of the 82574 can generate
tx hangs.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
klist.c: bit 0 in pointer can't be used as flag
debugfs: introduce stub for debugfs_create_size_t() when DEBUG_FS=n
sysfs: fix problems with binary files
PNP: fix broken pnp lowercasing for acpi module aliases
driver core: Convert '/' to '!' in dev_set_name()
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix cursor physical address choice to match the 2D driver.
drm: stash AGP include under the do-we-have-AGP ifdef
drm: don't whine about not reading EDID data
drm/i915: hook up LVDS DPMS property
drm/i915: remove unnecessary debug output in KMS init
i915: fix freeing path for gem phys objects.
drm: create mode_config idr lock
drm: fix leak of device mappings since multi-master changes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: fix lock imbalance in pciehp
PCI PM: Restore standard config registers of all devices early
PCI/MSI: bugfix/utilize for msi_capability_init()
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
i.MX31: framebuffer driver
i.MX31: Image Processing Unit DMA and IRQ drivers
dmaengine: add async_tx_clear_ack() macro
dmaengine: dma_issue_pending_all == nop when CONFIG_DMA_ENGINE=n
dmaengine: kill some dubious WARN_ONCEs
fsldma: print correct IRQ on mpc83xx
fsldma: check for NO_IRQ in fsl_dma_chan_remove()
dmatest: Use custom map/unmap for destination buffer
fsldma: use a valid 'device' for dma_pool_create
dmaengine: fix dependency chaining
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (22 commits)
dma-coherent: Restore dma_alloc_from_coherent() large alloc fall back policy.
dma-coherent: per-device coherent area is in pages, not bytes.
sh: fix unaligned and nonexistent address handling
nommu: Stub in vm_map_ram()/vm_unmap_ram()/vm_unmap_aliases().
sh: fix sh-sci / early printk build on sh7723
sh: export the sh7343 JPU to user space
sh: update defconfigs.
serial: sh-sci: Fix up SH7720/SH7721 SCI build.
sh: Kill off obsolete busses from arch/sh/Kconfig.
sh: sh7785lcr/highlander/hp6xx need linux/irq.h.
sh: Migo-R MMC support using spi_gpio and mmc_spi.
sh: ap325rxa MMC support using spi_gpio and mmc_spi
sh: mach-x3proto: needs linux/irq.h.
sh: Drop the BKL from sys_execve() on SH-5.
sh: convert rsk7203 to use smsc911x.
sh: convert magicpanelr2 platform to use smsc911x.
sh: convert ap325rxa platform to use smsc911x.
sh: mach-migor: Add tw9910 support.
sh: mach-migor: Delete soc_camera_platform setup.
sh: mach-migor: Add ov772x support.
...
Use '%zu' to print out a size_t variable, not '%d'. Another case of the
"let's keep at least Linus' defconfig compile warningless" rule.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debugobjects: add and use INIT_WORK_ON_STACK
rcu: remove duplicate CONFIG_RCU_CPU_STALL_DETECTOR
relay: fix lock imbalance in relay_late_setup_files
oprofile: fix uninitialized use of struct op_entry
rcu: move Kconfig menu
softlock: fix false panic which can occur if softlockup_thresh is reduced
rcu: add __cpuinit to rcu_init_percpu_data()
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (29 commits)
xen: unitialised return value in xenbus_write_transaction
x86: fix section mismatch warning
x86: unmask CPUID levels on Intel CPUs, fix
x86: work around PAGE_KERNEL_WC not getting WC in iomap_atomic_prot_pfn.
x86: use standard PIT frequency
xen: handle highmem pages correctly when shrinking a domain
x86, mm: fix pte_free()
xen: actually release memory when shrinking domain
x86: unmask CPUID levels on Intel CPUs
x86: add MSR_IA32_MISC_ENABLE bits to <asm/msr-index.h>
x86: fix PTE corruption issue while mapping RAM using /dev/mem
x86: mtrr fix debug boot parameter
x86: fix page attribute corruption with cpa()
Revert "x86: signal: change type of paramter for sys_rt_sigreturn()"
x86: use early clobbers in usercopy*.c
x86: remove kernel_physical_mapping_init() from init section
fix: crash: IP: __bitmap_intersects+0x48/0x73
cpufreq: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write
work_on_cpu: Use our own workqueue.
work_on_cpu: don't try to get_online_cpus() in work_on_cpu.
...
The return value of xenbus_write_transaction can be uninitialised in
the success case leading to the userspace xenstore utilities failing.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It supports VX855 and future chips whose IDE controller uses PCI ID 0x0571.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update Kconfig for sata_mv with full list of chips supported,
and (finally!) remove the "EXPERIMENTAL" designations.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable reliable use of Message-Signaled Interrupts (MSI) in sata_mv
by masking further chip interrupts within the main interrupt handler.
Based upon a suggestion by Grant Grundler.
MSI is working reliably in all of my test systems here now.
Signed-off-by: Mark Lord <mlord@pobox.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I noticed that during initialization sata_mv.c assumes that the main
interrupt mask has its default value of 0. The function
mv_platform_probe(..) initializes a shadow irq mask with 0 assuming
that's the value of the controller's register. Now
mv_set_main_irq_mask(..) only writes the controller's register if the
new value differs from the "shadowed" value. This is fatal when trying
to disable all interrupts in mv_init_host(..), i.e. the following
function call does not write anything to the main irq mask register:
mv_set_main_irq_mask(host, ~0, 0);
The effect I see on my machine (QNAP TS-109 II) with booting via kexec
(with Linux as a 2nd-stage boot loader) is that if the sata_mv module
was still loaded when performing kexec, then the new kernel's sata_mv
module starts up with interrupts enabled. This results in an unhandled
IRQ and breaks the boot process.
The unhandled interrupt itself might also be fixed by Lennert's patch
proposed at http://markmail.org/message/kwvzxstnlsa3s26w which I did not
try yet.
However I still propose to additionally initialize the shadow variable
with the current contents of the main irq mask register to get both in
sync and allow proper disabling the main irq mask. This fixes the
unhandled irq on my machine.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unneeded nsect restriction from GenII NCQ path,
and improve comments to explain why this is not a problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove silly read-modify-write sequences when clearing interrupts
in hc_irq_cause. This gets rid of unneeded MMIO reads, resulting in
a slight performance boost when switching between EDMA and non-EDMA
modes (eg. for cache flushes).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a longstanding bug for the 8-port Marvell Sata controllers (508x/6081),
where accesses to the upper 4 ports would cause lost-interrupts / timeouts
for the lower 4-ports. With this patch, the 6081 boards should finally be
reliable enough for mainstream use with Linux.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP5x family of controllers seem to share much more with nf2's as far
as reset protocol is concerned. It requires heardreset to get the PHY
going and classfication code report after hardreset is unreliable.
Create a new board type MCP5x and use noclassify hardreset. SWNCQ is
modified to inherit from this new type.
This fixes hotplug regression reported in kernel bz#12351.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
nv_nf2_hardreset() will be used by other flavors too. Rename it to
nv_noclassify_hardreset().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Asus Pundit-R with atiixp controller has the second port missing and,
very unusually, its status is stuck at 0x7f and all others at 0. This
meanst that it fails TF access test but gets detected as a disk due to
classification code check and then evades polling IDENTIFY presence
detection thanks to the missing BSY in the status value causing
excessive delays during boot.
This patch makes libata-sff HSM set NODEV_HINT if the status is 0x7f
to make polling IDENTIFY presence detection work for these machines.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EH message for NODEV_HINT path was describing the opposite
condition. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
802.1Q expanded the maximum ethernet frame size by 4 bytes for the
VLAN tag. We're not taking this into account in virtio_net, which
means the buffers we provide to the backend in the virtqueue RX ring
aren't big enough to hold a full MTU VLAN packet. For QEMU/KVM,
this results in the backend exiting with a packet truncation error.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/s390/net/lcs.c: In function 'lcs_new_device':
drivers/s390/net/lcs.c:2179: error: implicit declaration of function 'lcs_set_multicast_list'
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQF_DISABLED is not guaranteed for shared IRQs. I think power_changed_isr
doesn't need it anyway, as it only fires a timer.
This patch enables IRQF_SAMPLE_RANDOM instead.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
There is currently a DMA mapping leak that can occur in the ibmvfc
driver if we fail to allocate a scatterlist. Fix this by unmapping
the scatterlist in the failure path. Additionally, only log an error
for a scatterlist allocation failure if the log level is greater
than the default, since this can occur when running Active Memory
Sharing and this is not considered an error.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit f78badb1ae ([SCSI] fc
transport: pre-emptively terminate i/o upon dev_loss_tmo timeout)
changed the callback semantics of dev_loss_tmo and
terminate_rport_io such that repeated calls could be made. This
could result in the the driver using stale (NULLed-out, in
dev_loss_tmo) data from the rport. Correct this by addint a
simple check to ensure a valid fcport is attached.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jeremy Higdon noted
(http://marc.info/?l=linux-scsi&m=123262143131788&w=2) that the
rework done in commit e315cd28b9
was not setting the proper consistent and streaming DMA masks
prior to memory allocations. Correct this and remove the
unnecessary prototype.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When clearing the flash device's SR, the comment is incorrect...
clearing the SR is 2 steps:
1. the SR protect bit is 1, so the first write zero clears only
that bit,
2. the SR protect bit is now 0, so the next write zero clears the
remaining bits.
The sector erase debug print more correctly identifies that the erase failed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 73208dfd7a (qla2xxx: add
support for multi-queue adapter) inadvertently backed-out the fix
in 5bff55db3d (qla2xxx: Return a
FAILED status when abort mailbox-command fails.).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The flash data was incorrectly being converted (cpu_to_le32())
when using the bulk-flash-write mailbox command (ISP25xx and
above).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pre-ISP81XX parts (including ISP24xx and ISP25xx) could contain a
firmware image within a segment of flash, driver would fallback
to loading this firmware if the request-firmware interface failed
(userspace .bin file). Moving forward, all ISP81XX parts will
ship with a suggested-to-be-used firmware image within flash
which all driver should first attempt to load. If the flash
firmware load fails, the driver will then fallback to loading
firmware via the request-firmware interface (ql8100_fw.bin).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would incorrectly bypass serialization if the DPC
thread were performing a big-hammer operation (ISP abort). This
short circuit, though rare, would subsequently stomp on a
secondary thread's mailbox command execution. Found during
ISP81XX testing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code should work as well given qla24xx_reset_adapter()
is only called in extreme cases where the HBA is taken offline.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Also removes unneeded 'findex' local variable within routine.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
qla4xxx does not check the I_T nexus values correctly
so it ends up creating one session to the target. If
a portal should disappear or they should be reported
in different order the driver will think it is already
logged in when it could now be speaking to a different
target portal or accessing it through a different
initiator port (iscsi initiator port is not tied to
hardware and is just the initiator name plus isid
so you could end up with multiple ports through one
host).
This patch has the driver check the iscsi scsi port
values when matching sessions (we do not check
the initiator name because that is static). It results
in a portal from each target portal group getting
logged into instead of just one per target. In the future
the firmware should hopefully send us notification of other
sessions that are created to other portals within the
same tpgt and the sessions should have different isids.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I am not sure what happened. It looks like we have always leaked
the q->queue that is allocated from the kfifo_init call. nab finally
noticed that we were leaking and this patch fixes it by adding a
kfree call to iscsi_pool_free. kfifo_free is not used per kfifo_init's
instructions to use kfree.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
spin_lock functions take a pointer to the lock, not the lock itself.
This error was noticed by compiling ebsa110_defconfig for linux-rt where
the locking functions obviously are more picky about their arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Roel Kluin <12o3l@tiscali.nl>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a regression by "firewire: keep highlevel drivers attached
during brief connection loss": There were 2 seconds unnecessary waiting
added to the shutdown procedure of each controller.
We use card->link as status flag to signal the device handler that there
is no use to wait for a come-back.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The driver was updated for OMAP34xx, but the Kconfig file was missed.
So this adds the missing parts from d99241c in Tony Lindgren's tree:
Add watchdog timer support for TI OMAP3430.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add omap hsmmc controller for 2430 and 34xx.
Note that this controller has different registers compared to
the earlier omap MMC controller, so sharing code currently is
not possible.
Various updates and fixes from linux-omap list have been
merged into this patch.
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since dma.h has been moved to arch/arm/mach-s3c2410/include/mach,
use the new include path.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Camcorders have a tendency to fail read requests to their config ROM and
write request to their FCP command register with ack_busy_X. This has
become a problem with newer kernels and especially Panasonic camcorders,
causing AV/C in dvgrab and kino to fail. Dvgrab for example frequently
logs "send oops"; kino reports loss of AV/C control. I suspect that
lower CPU scheduling latencies in newer kernels made this issue more
prominent now.
According to
https://sourceforge.net/tracker/?func=detail&atid=114103&aid=2492640&group_id=14103
this can be fixed by configuring the FireWire controller for more
hardware retries for request transmission; these retries are evidently
more successful than libavc1394's own retry loop (typically 3 tries on
top of hardware retries).
Presumably the same issue has been reported at
https://bugzilla.redhat.com/show_bug.cgi?id=449252 and
https://bugzilla.redhat.com/show_bug.cgi?id=477279 .
Tested-by: Mathias Beilstein
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Camcorders have a tendency to fail read requests to their config ROM and
write request to their FCP command register with ack_busy_X. This has
become a problem with newer kernels and especially Panasonic camcorders,
causing AV/C in dvgrab and kino to fail. Dvgrab for example frequently
logs "send oops"; kino reports loss of AV/C control. I suspect that
lower CPU scheduling latencies in newer kernels made this issue more
prominent now.
According to
https://sourceforge.net/tracker/?func=detail&atid=114103&aid=2492640&group_id=14103
this can be fixed by configuring the FireWire controller for more
hardware retries for request transmission; these retries are evidently
more successful than libavc1394's own retry loop (typically 3 tries on
top of hardware retries).
Presumably the same issue has been reported at
https://bugzilla.redhat.com/show_bug.cgi?id=449252 and
https://bugzilla.redhat.com/show_bug.cgi?id=477279 .
In a quick test with a JVC camcorder (which didn't malfunction like the
reported camcorders), this change decreased the number of ack_busy_X
from 16 in three runs of dvgrab to 4 in three runs of the same capture
duration.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The present message is mostly just noise. We only need to be notified
if the "active" flag does not go off before the retry loop terminates.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The RTL8187 and RTL8187B devices can stall unless an explicit termination
packet is sent.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ieee80211_sta structure there is u64 supp_rates[IEEE80211_NUM_BANDS]
this is filled with all support rate from assoc_resp. If we associate
with G-band AP only supp_rates of G-band will be set the other band
supp_rates will be set to 0. If the user type this command
this will cause mac80211 to set to new channel, mac80211
does not disassociate in setting new channel, so the active
band is now A-band. then in handling the new essid mac80211 will
kick in the assoc steps which involve sending disassociation frame.
in this mac80211 will WARN_ON sta->supp_rates[A_BAND] == 0.
This fixes:
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1822http://www.kerneloops.org/searchweek.php?search=rs_get_rate
Signed-off-by: mohamed abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Artur Skawina confirmed that the first generation devices needs the same
URB_ZERO_PACKET flag, in oder to finish the pending transfer properly.
The second generation has been successfully fixed by
"p54usb: fix random traffic stalls (LM87)" (43af18f06d5)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 1058a75f07 ("xen: actually release
memory when shrinking domain") causes a crash if the page being released
is a highmem page.
If a page is highmem then there is no need to unmap it.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this:
> It appears that in the upstream balloon driver,
> the call to HYPERVISOR_update_va_mapping is missing
> from decrease_reservation. I think as a result,
> the balloon driver is eating memory but not
> releasing it to Xen, thus rendering the balloon
> driver essentially useless. (Can be observed via xentop.)
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All supported SMSC PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic genphy_{suspend,resume}
functions.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suspend/resume routines check for phydrv != NULL, but that is
wrong because "phydrv" comes from container_of(drv). If drv is NULL,
then container_of(drv) will return non-NULL result, and the checks
won't work.
The Freescale TBI PHYs are driver-less, so "drv" is NULL, and that
leads to the following oops:
Unable to handle kernel paging request for data at address 0xffffffe4
Faulting instruction address: 0xc0215554
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c0215554] mdio_bus_suspend+0x34/0x70
LR [c01cc508] suspend_device+0x258/0x2bc
Call Trace:
[cfad3da0] [cfad3db8] 0xcfad3db8 (unreliable)
[cfad3db0] [c01cc508] suspend_device+0x258/0x2bc
[cfad3dd0] [c01cc62c] dpm_suspend+0xc0/0x140
[cfad3e20] [c01cc6f4] device_suspend+0x48/0x5c
[cfad3e40] [c0068dd8] suspend_devices_and_enter+0x8c/0x148
[cfad3e60] [c00690f8] enter_state+0x100/0x118
[cfad3e80] [c00691c0] state_store+0xb0/0xe4
[cfad3ea0] [c018c938] kobj_attr_store+0x24/0x3c
[cfad3eb0] [c00ea9a8] flush_write_buffer+0x58/0x7c
[cfad3ed0] [c00eadf0] sysfs_write_file+0x58/0xa0
[cfad3ef0] [c009e810] vfs_write+0xb4/0x16c
[cfad3f10] [c009ed40] sys_write+0x4c/0x90
[cfad3f40] [c0014954] ret_from_syscall+0x0/0x38
[...]
This patch fixes the issue, plus removes unneeded parentheses
and fixes indentation level in mdio_bus_suspend().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A link change interrupt might be queued and activated after the loopback was set
and it will cause the loopback to fail. The PHY lock should be kept until the
loopback test is over.
That implies that the bnx2x_test_link should used within the loopback function
and not bnx2x_wait_for_link since that function also takes the PHY link
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Waiting for the FW to response requires a memory barrier
Signed-off-by: Michal Kalderon <michals@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmmod might hang without this patch since the reference counter is not going
down
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call carrier off should not be called after register_netdev since after
register netdev open can be called at any time followed by an interrupt that
will set it to carrier_on and the probe will resume control and set it to off
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failures on load were not handled correctly - separate the flow to handle
different failures
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi disabled unconditionally at netif stop
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid complications, make sure that the HW is in reset (as it should be)
before trying to take it out of reset. In normal flows, the HW is indeed in rest
so this should have no effect
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be consistent with mac80211 drivers and return correct return code.
NETDEV_TX_OK is 0, but we need to be consistent wrt formatting amongst
implementations
re: http://marc.info/?l=linux-wireless&m=123119327419865&w=2
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Giuseppe Cala <jiveaxe@gmail.com> (The second "a" in "Cala" should be
a grave, U+00E0) reported success on zd1211-devs@lists.sourceforge.net.
The chip info is:
zd1211b chip 0df6:0036 v4810 high 00-0c-f6 AL2230_RF pa0 g--N-
The Sitecom WL-603 is detected as a zd1211b with a AL2230 RF transceiver chip.
Signed-off-by: Giuseppe Cala <jiveaxe@gmail.com>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In theory, the firmware acks the received a data frame, before signaling the driver to free it again.
However Artur Skawina <art.08.09@gmail.com> has shown that it can happen in reverse order as well.
This is very bad and could lead to memory corruptions, oopses and panics.
Thanks to Artur Skawina <art.08.09@gmail.com> for reporting and debugging this issue.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Artur Skawina <art.08.09@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we let the firmware do the data encryption, we have to remove the ICV and
(M)MIC at the end of the frame before we can give it back to mac80211.
Or, these data frames have a few trailing bytes on cooked monitor interfaces.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a obvious memory leak in the eeprom parser.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
KERN_INFO is too "loud" for messages that are generated by the ordinary
events, such as accociation. Use of KERN_DEBUG is consistent with
mac80211.
Suggested by Michael Gilbert <michael.s.gilbert@gmail.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 provides 2 structures to handle bitrates, namely
ieee80211_rate and ieee80211_tx_rate. To determine the short preamble
mode for an outgoing frame, the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE
must be checked on ieee80211_tx_rate and not ieee80211_rate (which rt2x00 did).
This fixes a regression which was triggered in 2.6.29-rcX as reported by Chris Clayton.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-By: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the MIPS with DRM build.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make this message a little quieter, since it's common and not necessarily
indicative of a problem.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The LVDS output supports DPMS calls, but we never hooked up the property code,
so set property calls didn't actually do anything. Implement a set_property
callback for the LVDS output so that the right thing happens.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Create a separate mode_config IDR lock for simplicity. The core DRM
config structures (connector, mode, etc. lists) are still protected by
the mode_config mutex, but the CRTC IDR (used for the various identifier
IDs) is now protected by the mode_config idr_mutex. Simplifies the
locking a bit and removes a warning.
All objects are protected by the config mutex, we may in the future,
split the object further to have reference counts.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
mcs7830_set_reg() and mcs7830_get_reg() are called with buffers
from stack which must not be used directly for USB transfers.
This causes corruption of the stack particulary on non x86
architectures because DMA may be used for these transfers.
Signed-off-by: Christian Eggers <christian.eggers@kathrein.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve usbnet's devdbg to always type-check diagnostic arguments,
like dev_dbg (device.h). This makes no change to the resulting size of
usbnet modules.
This patch also removes an #ifdef DEBUG directive from rndis_wlan so
it's devdbg statements are always type-checked at compile time.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a framebuffer driver for i.MX31 SoCs. It only supports synchronous
displays, vertical panning supported, no overlay support.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds the SCSPTR register to the sh-sci driver in
the case of sh7723 to make sure early printk builds properly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 3ada8b7e ("block: struct device - replace bus_id with dev_name(),
dev_set_name()") deleted the code in register_disk() that changed a '/'
to a '!' in the device name when registering a disk, but dev_set_name()
does not perform this conversion.
This leads to amusing problems with disks that have '/' in their names:
for example a failure to boot with the root partition on a cciss device,
even though the kernel says it knows about the root device:
VFS: Cannot open root device "cciss/c0d0p6" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
6800 71652960 cciss/c0d0 driver: cciss
6802 1 cciss/c0d0p2
6805 2931831 cciss/c0d0p5
6806 34354908 cciss/c0d0p6
6810 71652960 cciss/c0d1 driver: cciss
Fix this by adding code to change '/' to '!' in dev_set_name() to handle
this until dev_set_name() is converted to use kobject_set_name().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
while(--j >= 0) keeps spinning when j is unsigned:
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't forget to call pci_disable_device() in myri10ge_remove()
and when myri10ge_probe() fails.
By the way, update the copyright years.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be prepared for /proc/acpi/event removal we export events
also through generic netlink interface.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
The Eee implements rfkill by logically unplugging the wireless card from the
PCI bus. Despite sending ACPI notifications, this does not appear to be
implemented using standard ACPI hotplug - nor does the firmware provide the
_OSC method required to support native PCIe hotplug. The only sensible choice
appears to be to handle the hotplugging directly in the eeepc-laptop driver.
Tested successfully on a 700, 900 and 901.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Error out if rfkill registration fails, and also set the default system state
appropriately on boot
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Newer Eees have extra hotkeys above the function keys. This patch adds support
for sending them through the input layer.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Update Kconfig, now asus-laptop use the input layer.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is based on eeepc-laptop.c and the patchs
from Nicolas Trangez and Daniel Nascimento (mainly for the keymap).
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
To be prepared for /proc/acpi/event removal we export events
also through generic netlink interface.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
eeepc_backlight_exit() was doing rfkill and input stuff, which
is a nonsense. This patch add two specific exit functions, one
for input and one for rfkill.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
There are situations when nodes vanish from the bus and come back
quickly thereafter:
- When certain bus-powered hubs are plugged in,
- when certain devices are plugged into 6-port hubs,
- when certain disk enclosures are switched from self-power to bus
power or vice versa and break the daisy chain during the transition,
- when the user plugs a cable out and quickly plugs it back in, e.g.
to reorder a daisy chain (works on Mac OS X if done quickly enough),
- when certain hubs temporarily malfunction during high bus traffic.
Until now, firewire-core reported affected nodes as lost to the
highlevel drivers (firewire-sbp2 and userspace drivers). We now delay
the destruction of device representations until after at least two
seconds after the last bus reset. If a "new" device is detected in this
period whose bus information block and root directory header match that
of a device which is pending for deletion, we resurrect that device and
send update calls to highlevel drivers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Noticed by Jarod Wilson: The bus manager work was unnecessarily delayed
each time the bus generation counter rolled over.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
The whole topology code only works if the old and new topologies which
are compared come from immediately successive self ID complete events.
If there happened bus resets without self ID complete events in the
meantime, or self ID complete events with invalid selfIDs, the topology
comparison could identify nodes wrongly, or more likely just corrupt
kernel memory or panic right away.
We now discard all nodes of the old topology and treat all current nodes
as new ones if the current self ID generation is not the previous one
plus 1.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
GregKH asked to fix UBI which has fake device release method. Indeed,
we have to free UBI device description object from the release method,
because otherwise we'll oops is someone opens a UBI device sysfs file,
then the device is removed, and he reads the file. With this fix, he
will get -ENODEV instead of an oops.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Roel Kluin reported a bug in two error paths where skbs were wrongly
being freed using kfree(). He provided a fix where it was replaced to
kfree_skb(), as it should be.
However, in i2400mu_rx(), the error path was missing returning an
indication of the failure. Changed to reset rx_skb to NULL and return
it to the caller, i2400mu_rxd(). It will be treated as a transient
error and just ignore the packet.
Depending on the buffering conditions inside the device, the data
packet might be dropped or the device will signal the host again for
data-ready-to-read and the host will retry.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to what the docs say, the 'extended interrupt cause' bit in
the interrupt cause register (bit 1) appears to not be maskable on at
least some of the mv643xx_eth platforms, making writing zeroes to the
interrupt mask register but not the extended interrupt mask register
insufficient to stop interrupts from occuring. Therefore, also write
zeroes to the extended interrupt mask register when shutting down the
port.
This fixes the interrupt storm seen on the Pegasos board when shutting
down the interface.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 66e63ffbc0 ("mv643xx_eth:
implement ->set_rx_mode()") cleaned up mv643xx_eth's multicast filter
programming, but broke it as well.
The non-special multicast filter table (for multicast addresses that
are not of the form 01:00:5e:00:00:xx) consists of 256 hash table
buckets organised as 64 32-bit words, where the 'accept' bits are
in the LSB of each byte, so in bits 24 16 8 0 of each 32-bit word.
The old code got this right, but the referenced commit broke this by
using bits 3 2 1 0 instead. This commit fixes this up.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit cd4ccf76bf.
On the Pegasos board, we can't do DMA burst that are longer than
one cache line. For now, go back to using 32 byte DMA bursts for
all mv643xx_eth platforms -- we can switch the ARM-based platforms
back to doing long 128 byte bursts in the next development cycle.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reported-by: Alan Curry <pacman@kosh.dhis.org>
Reported-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies how the tg3 driver handles device firmware.
The patch starts by consolidating David Woodhouse's earlier patch under
the same name. Specifically, the patch moves the request_firmware call
into a separate tg3_request_firmware() function and calls that function
from tg3_open() rather than tg3_init_one().
The patch then goes on to limit the number of devices that will make
request_firmware calls. The original firmware patch unnecessarily
requested TSO firmware for devices that did not need it. This patch
reduces the set of devices making TSO firmware patches to approximately
the following device set : 5703, 5704, and 5705.
Finally, the patch reduces the effects of a request_firmware() failure.
For those devices that are requesting TSO firmware, the driver will turn
off the TSO capability. If TSO firmware becomes available at a later
time, the device can be closed and then opened again to reacquire the
TSO capability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx
queues is redundant and unnecessary. By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register VLAN ID 0 so that frames with VLAN ID 0 are received and get
their tag stripped when ixgbe is not in DCB mode. VLAN ID 0 means
that the frame is 'priority tagged' only - it is not a VLAN, but the
priority value is the tag in valid. The functions
ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a
couple functions to correct compiling issues with this change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The is an issue where setting Relaxed Ordering (RO) bit
(in a PCI-E write transaction) on 82598 causing the chipset
to drop DCA hints. This patch forces RO not to be set for
descriptors as well as payload. This will only be in effect
while DCA is enabled and no performance difference was
noticed in testing.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the assigned value is being overwritten shortly after, it can be
dropped and so the whole variable definition moved to the start of the
function.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is copy and paste from the original driver. As skb_reserve() is
also called within korina_alloc_ring() when initially allocating the
receive descriptors, the same should be done when allocating new space
after passing an skb to upper layers.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last loop iteration, i has the value RC32434_NUM_RDS and
therefore leads to an index overflow when used afterwards to address the
last element. This is yet another another bug introduced when rewriting
parts of the driver for upstream preparation, as the original driver
used 'RC32434_NUM_RDS - 1' instead.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lro manager's frag_align_pad setting was missing,
leading to misaligned access to the skb passed up
to the stack.
Tested-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases when an underrun occur, all macb buffers where consumed
and the netif_queue was stopped infinitely. This happens then the TGO
(transfer ongoing) bit in the TSR is set (and UND). It seems like
clening up after the underrun makes the driver and the macb hardware
end up in an inconsistent state. The result of this is that in the
following calls to macb_tx no TX buffers are released -> the
netif_queue was stopped, and never woken up again.
The solution is to disable the transmitter, if TGO is set, before
clening up after the underrun, and re-enable the transmitter when the
cleaning up is done.
Signed-off-by: Richard Röjfors <richard.rojfors@endian.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating the version and the year of updated files
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make sure no swapping are made by the compiler, changed HAS_WORK to inline
functions and added all the necessary barriers
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Driver supports the 57711 and 57711E as well but the description was out of
date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the default PHY version (0x4321) is read - the PHY FW load failed
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10M/100M autoneg was not establishing link.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting loopback requires time to take effect
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW should be configured so fast toggling between 1G and 10G will not be
missed. Make sure that the HW is re-configured in full
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the page size is > 8KB this violation happens
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't dump eeprom when bnx2x adapter is down. Running ethtool -e causes an eeh
without it when the device is down
Signed-off-by: Paul Larson <pl@linux.vnet.ibm.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Magnus Damm