-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVIws/AAoJEHm+PkMAQRiGwEcH/1GCBqrBzXaKwDdCPMRcYVUb
MYkXmGkCGRYWe5MXI8QNAaa/CdG6mAFMHWN6CaMMpLTxnM1m87uBg01fQMsh73BO
mRVLKE/soiJDnR1gYzBBDBYV/AUvytN5PhgeNaA95YIJvU3T1f3iTnV8vs30Dp0L
YpxSqwr3C0k7C9IE0VcgfzvWJPCnQ9IWHuX3jn5s1XjGKVNbBYHMt6FusHdyXMfT
dp8ksuGHwm30mTFI5xJpKOrRzfi+P5EsEUrsnFRPRM/iFTVrM5R7eaUhsRZb2+Wo
YApnbYhUYz7om1AuQ+UZ/+S6y7ZLlGWegI1lWI754GIsczG5vPHEYhhgkzMhTsc=
=kR1V
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc7' into next
Sync up with Linux 4.0-rc7 to bring in ALPS changes.
All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now GPIO syscon driver produces bunch of warnings during the
boot of Kesytone 2 SoCs:
gpio-syscon soc:keystone_dsp_gpio@02620240: can't read the dir register offset!
gpio-syscon soc:keystone_dsp_gpio@2620244: can't read the dir register offset!
This message unintentionally was added using dev_err(), but its
actual log level is debug, because third cell of "ti,syscon-dev" is
optional.
Hence change it to dev_dbg() as it should be.
This patch fixes commit:
5a3e3f8 ("gpio: syscon: retriave syscon node and regs offsets from dt")
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If GPIO driver use pin mapping, need to translate pin number
between ACPI table and GPIO driver.
This issue is found on one platform with Cherryview gpio
controller, kernel is hang when executed _PS0 method of
one ACPI device, since without this translation, it access
invalid gpiodesc array.
Verified it works again with this patch.
Signed-off-by: qipeng.zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 98686d9a52 ("gpio: mpc8xxx: Convert to platform device
interface"), we get the following section mismatch warning. Remove the
__initdata annotation to fix it.
WARNING: vmlinux.o(.data+0xbc28): Section mismatch in reference from the variable mpc8xxx_plat_driver to the variable .init.data:mpc8xxx_gpio_ids
The variable mpc8xxx_plat_driver references
the variable __initdata mpc8xxx_gpio_ids
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio_chip operations receive a pointer the gpio_chip struct which is
contained in the driver's private struct, yet the container_of call in those
functions point to the mfd struct defined in include/linux/mfd/tps65912.h.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change:
7b8792bbdf
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
assumed that only one gpio-chip is registred per of-node.
Some drivers register more than one chip per of-node, so
adjust the matching function of_gpiochip_find_and_xlate to
not stop looking for chips if a node-match is found and
the translation fails.
Cc: Stable <stable@vger.kernel.org>
Fixes: 7b8792bbdf ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags")
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Tyler Hall <tylerwhall@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull ARM updates from Russell King:
- clang assembly fixes from Ard
- optimisations and cleanups for Aurora L2 cache support
- efficient L2 cache support for secure monitor API on Exynos SoCs
- debug menu cleanup from Daniel Thompson to allow better behaviour for
multiplatform kernels
- StrongARM SA11x0 conversion to irq domains, and pxa_timer
- kprobes updates for older ARM CPUs
- move probes support out of arch/arm/kernel to arch/arm/probes
- add inline asm support for the rbit (reverse bits) instruction
- provide an ARM mode secondary CPU entry point (for Qualcomm CPUs)
- remove the unused ARMv3 user access code
- add driver_override support to AMBA Primecell bus
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (55 commits)
ARM: 8256/1: driver coamba: add device binding path 'driver_override'
ARM: 8301/1: qcom: Use secondary_startup_arm()
ARM: 8302/1: Add a secondary_startup that assumes ARM mode
ARM: 8300/1: teach __asmeq that r11 == fp and r12 == ip
ARM: kprobes: Fix compilation error caused by superfluous '*'
ARM: 8297/1: cache-l2x0: optimize aurora range operations
ARM: 8296/1: cache-l2x0: clean up aurora cache handling
ARM: 8284/1: sa1100: clear RCSR_SMR on resume
ARM: 8283/1: sa1100: collie: clear PWER register on machine init
ARM: 8282/1: sa1100: use handle_domain_irq
ARM: 8281/1: sa1100: move GPIO-related IRQ code to gpio driver
ARM: 8280/1: sa1100: switch to irq_domain_add_simple()
ARM: 8279/1: sa1100: merge both GPIO irqdomains
ARM: 8278/1: sa1100: split irq handling for low GPIOs
ARM: 8291/1: replace magic number with PAGE_SHIFT macro in fixup_pv code
ARM: 8290/1: decompressor: fix a wrong comment
ARM: 8286/1: mm: Fix dma_contiguous_reserve comment
ARM: 8248/1: pm: remove outdated comment
ARM: 8274/1: Fix DEBUG_LL for multi-platform kernels (without PL01X)
ARM: 8273/1: Seperate DEBUG_UART_PHYS from DEBUG_LL on EP93XX
...
- GPIOLIB core changes:
- Create and use of_mm_gpiochip_remove() for removing
memory-mapped OF GPIO chips
- GPIO MMIO library suppports bgpio_set_multiple for
switching several lines at once, a feature merged in
the last cycle.
- New drivers:
- New driver for the APM X-gene standby GPIO controller
- New driver for the Fujitsu MB86S7x GPIO controller
- Cleanups:
- Moved rcar driver to use gpiolib irqchip
- Moxart converted to the GPIO MMIO library
- GE driver converted to GPIO MMIO library
- Move sx150x to irqdomain
- Move max732x to irqdomain
- Move vx855 to use managed resources
- Move dwapb to use managed resources
- Clean tc3589x from platform data
- Clean stmpe driver to use device tree only probe
- New subtypes:
- sx1506 support in the sx150x driver
- Quark 1000 SoC support in the SCH driver
- Support X86 in the Xilinx driver
- Support PXA1928 in the PXA driver
- Extended drivers:
- max732x supports device tree probe
- sx150x supports device tree probe
- Various minor cleanups and bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJU2W1HAAoJEEEQszewGV1zuRkQAKBukQwx46zQuFH8oalSuxmy
H2/ESMnDmRlBI0zX+dAGDg4HlkO9VwIrdcyzMMe7uO8EFUu9d4/mu2E1f8cY2mxu
kwUSntVaYGVPVj/Vok3kzq1wW/pUQ9E2iMbNeDVZJH/cqEvylPPa2LZ3hZVri57J
orJzaYtZWf640y3McGTUDwIQokgxxdMMyWfm26P1iZkByjofUaYRHS1NIxhKVSVC
Y6uA/Ivvh56ezlPQykc7m6YEjoUS91AMllJca1A3KF3+qvQ3Hnc+i9mB7hAQbJ8L
6Iv2qCD4TgtWT5YXgP0eZsfSV/19kvlVlGX7QQT6o7uIFOLVNOmX9FJAc4n3SGNI
HbxsDdlF9XHVFh0XyKcBQfg0uUmRWUDQ/LsXn9KL6Yrpyx3QZGH/PTYl/XoCj1IO
IL6Bw51FCBXvCvLP5alXMouosAxrc19YpljcAuAMmjVTXe6RoULOZJs+lhTHMhvj
S6FWr6l0XDr4yKb0SXTOGI4hvRJvL8SWnIt5ezZrNrTKLsklL3Bi/o3BoKzzxmqS
6l/rxvcVUov455IrfqJ0ZEM6ZxC9/cvGec0RFyglopNSlKeTQsgWRNa6Pw2xZVk8
orT+G3L4jZ1+0hcjcSwfvHng5Nv6DuhIfUNPbLF/ZzmJcBPqGc/DuhGkFqOrBaXg
ey7Lua6+l+8zcDtugRRG
=yWrB
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the GPIO bulk changes for the v3.20 series:
GPIOLIB core changes:
- Create and use of_mm_gpiochip_remove() for removing memory-mapped
OF GPIO chips
- GPIO MMIO library suppports bgpio_set_multiple for switching
several lines at once, a feature merged in the last cycle.
New drivers:
- New driver for the APM X-gene standby GPIO controller
- New driver for the Fujitsu MB86S7x GPIO controller
Cleanups:
- Moved rcar driver to use gpiolib irqchip
- Moxart converted to the GPIO MMIO library
- GE driver converted to GPIO MMIO library
- Move sx150x to irqdomain
- Move max732x to irqdomain
- Move vx855 to use managed resources
- Move dwapb to use managed resources
- Clean tc3589x from platform data
- Clean stmpe driver to use device tree only probe
New subtypes:
- sx1506 support in the sx150x driver
- Quark 1000 SoC support in the SCH driver
- Support X86 in the Xilinx driver
- Support PXA1928 in the PXA driver
Extended drivers:
- max732x supports device tree probe
- sx150x supports device tree probe
Various minor cleanups and bug fixes"
* tag 'gpio-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: kconfig: replace PPC_OF with PPC
gpio: pxa: add PXA1928 gpio type support
dt/bindings: gpio: add compatible string for marvell,pxa1928-gpio
gpio: pxa: remove mach IRQ includes
gpio: max732x: use an inline function for container cast
gpio: use sizeof() instead of hardcoded values
gpio: max732x: add set_multiple function
gpio: sch: Consolidate similar algorithms
gpio: tz1090-pdc: Use resource_size to fix off-by-one resource size calculation
gpio: ge: Convert to use devm_kstrdup
gpio: correctly use const char * const
gpio: sx150x: fixup OF support
gpio: mpc8xxx: Use of_mm_gpiochip_remove
gpio: Add Fujitsu MB86S7x GPIO driver
gpio: mpc8xxx: Convert to platform device interface.
gpio: zevio: Use of_mm_gpiochip_remove
gpio: gpio-mm-lantiq: Use of_mm_gpiochip_remove
gpio: gpio-mm-lantiq: Use of_property_read_u32
gpio: gpio-mm-lantiq: Do not replicate code
gpio :gpio-mm-lantiq: Use devm_kzalloc
...
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for PXA1928 GPIOs. The PXA1928 adds a 6th bank from previous
generations.
Signed-off-by: Jing Xiang <jxiang@marvell.com>
Signed-off-by: Xiangzhan Meng <mengxzh@marvell.com>
[robh: ported to 3.19 from vendor kernel]
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to enable ARCH_MMP on ARM64, the include of mach/irqs.h
must be eliminated. mach/irqs.h was being included for IRQ_GPIO{0,1},
but these IRQs are always passed in as resources now. We can use irq0
and irq1 and get rid of IRQ_GPIOx. Get rid of the ifdef in the process
as it is no longer needed.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cast the struct gpio_chip into a max732x_chip using an inline
macro and move the assignment to the variable declaration
to save lines and simplify things.
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiolib uses a fixed string for the suffixes and defines it at 32 bytes.
Later in the code snprintf is used with this fixed value of 32. Using
sizeof() is safer in case the size for the suffixes is ever changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a set_multiple function to the MAX732x GPIO driver,
allowing for performance gains when using gpiod_set_array().
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak in the gpio sysfs interface due to failure to drop
reference to device returned by class_find_device when setting the
gpio-line polarity.
Fixes: 0769746183 ("gpiolib: add support for changing value polarity
in sysfs")
Cc: stable <stable@vger.kernel.org> # v2.6.33
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak in the gpio sysfs interface due to failure to drop
reference to device returned by class_find_device when creating a link.
Fixes: a4177ee7f1 ("gpiolib: allow exported GPIO nodes to be named
using sysfs links")
Cc: stable <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As a part of driver consolidation, move GPIO-related IRQ code to
drivers/gpio/gpio-sa1100.c. The code does not use GPIOLIB_IRQCHIP (yet),
because sa1100 does not have a device for gpios, which is a requirement
for GPIOLIB_IRQCHIP. This will be the next step.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Low GPIO pins use an interrupt in SC interrupts space. However it's
possible to handle them as if all the GPIO interrupts are instead tied
to single GPIO handler, which later decodes GEDR register and
chain-calls next IRQ handler. So split first 11 interrupts into system
part (IRQ_GPIO0_SC - IRQ_GPIO10_SC) which work exactly like the rest of
system controller interrupts and real GPIO interrupts
(IRQ_GPIO0..IRQ_GPIO10). A single handler sa1100_gpio_handler then
decodes and calls next handler.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidating similar algorithms into common functions to make
GPIO SCH simpler and manageable.
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_kstrdup to simplify the error handling path.
Also return -ENOMEM instead of 0 if devm_kstrdup fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On my previous patch I was overly hasty and made the suffixes string
array
const char const *suffixes, instaed of const char * const suffixes. This
patch corrects that
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create default gpio base if neither device node nor
platform data is defined.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Antonio Fiol <antonio@fiol.es>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Similar to omap_gpio_irq_type() let's make sure that the GPIO
is usable as an interrupt if the platform init code did not
call gpio_request(). Otherwise we can get invalid device access
after setup_irq():
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x214/0x340()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Idle): Data Access in Supervisor mode during Functional access
...
[<c05f21e4>] (__irq_svc) from [<c05f1974>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[<c05f1974>] (_raw_spin_unlock_irqrestore) from [<c00914a8>] (__setup_irq+0x244/0x530)
[<c00914a8>] (__setup_irq) from [<c00917d4>] (setup_irq+0x40/0x8c)
[<c00917d4>] (setup_irq) from [<c0039c8c>] (omap_system_dma_probe+0x1d4/0x2b4)
[<c0039c8c>] (omap_system_dma_probe) from [<c03b2200>] (platform_drv_probe+0x44/0xa4)
...
We can fix this the same way omap_gpio_irq_type() is handling it.
Note that the long term solution is to change the gpio-omap driver
to handle the banks as separate driver instances. This will allow
us to rely on just runtime PM for tracking the bank specific state.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make OF conditional on CONFIG_OF_GPIO, rename and register
the match table.
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for Fujitsu MB86S7x SoCs that have a memory mapped GPIO controller.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Tetsuya Nuriya <nuriya.tetsuya@jp.fujitsu.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This way we do not need to transverse the device tree manually.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of parsing manually the shadow content, use the much simpler
helper of_property_read_u32.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Require that device tree be used with STMPE (all platforms use this)
and enforce OF_GPIO, then delete the platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for standby GPIO controller of APM X-Gene SoCs on arm64.
Signed-off-by: Y Vo <yvo@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current sx150x gpio expander driver doesn't support
DTS. Now we added dts support for this driver.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add set_multiple functions to the generic driver for memory-mapped GPIO
controllers to improve performance when setting multiple outputs
simultaneously.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit ffe4770b9b ("gpio-amd8111: check ioport_map return value")
adds the error check on ioport_map(). It doesnt release the requested region.
On failure this patch release the region that has requested before.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Reported-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Include linux/slab.h to fix following compilation error.
drivers/gpio/gpio-ge.c: In function ‘gef_gpio_probe’:
drivers/gpio/gpio-ge.c:95:2: error: implicit declaration of function ‘kfree’ [-Werror=implicit-function-declaration]
kfree(bgc->gc.label);
Signed-off-by: Kamlakant Patel <kamlakant.patel@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
that have been around forever in the GPIO subsystem, most of them
also tagged for stable:
- A large slew of fixes from Johan Hovold who is finally testing and
reviewing the removal path of the GPIO drivers.
- Fix of_get_named_gpiod_flags() so it works as expected.
- Fix an IRQ handling bug in the crystalcove driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ekXq
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a set of fixes that mainly appeared when Johan Hovold started
exercising the removal path of the GPIO library, dealing with
hotplugging of GPIO controllers. Details from tag:
A slew of fixes dealing with some irritating bugs (non-regressions)
that have been around forever in the GPIO subsystem, most of them also
tagged for stable:
- A large slew of fixes from Johan Hovold who is finally testing and
reviewing the removal path of the GPIO drivers.
- Fix of_get_named_gpiod_flags() so it works as expected.
- Fix an IRQ handling bug in the crystalcove driver"
* tag 'gpio-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
gpio: sysfs: fix gpio attribute-creation race
gpio: sysfs: fix gpio device-attribute leak
gpio: sysfs: fix gpio-chip device-attribute leak
gpio: unregister gpiochip device before removing it
gpio: fix sleep-while-atomic in gpiochip_remove
gpio: fix memory leak and sleep-while-atomic
gpio: clean up gpiochip_add error handling
gpio: fix gpio-chip list corruption
gpio: fix memory and reference leaks in gpiochip_add error path
gpio: crystalcove: use handle_nested_irq
of_get_named_gpiod_flags fails with -EPROBE_DEFER in cases
where the gpio chip is available and the GPIO translation fails.
This causes drivers to be re-probed erroneusly, and hides the
real problem(i.e. the GPIO number being out of range).
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the coding style issue by adding a blank line after declaration
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
X86 Kconfig symbol is X86, not ARCH_X86.
Fixes: c586b3075d5b47d8 (gpio/xilinx: Add support for X86 Arch)
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dmitry Torokhov