Here is the large set of char, misc, and other driver subsystem updates
for 5.19-rc1. The merge request for this has been delayed as I wanted
to get lots of linux-next testing due to some late arrivals of changes
for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers
and cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that
below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no reported
problems.
Note, there are 3 merge conflicts when merging this with your tree:
- MAINTAINERS, should be easy to resolve
- drivers/slimbus/qcom-ctrl.c, should be straightforward
resolution
- drivers/misc/lkdtm/stackleak.c, not an easy resolution. This
has been noted in the linux-next tree for a while, and
resolved there, here's a link to the resolution that Stephen
came up with and that Kees says is correct:
https://lore.kernel.org/r/20220509185344.3fe1a354@canb.auug.org.au
I will be glad to provide a merge point that contains these resolutions
if that makes things any easier for you.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnkbA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylOrgCggbbAFwESBY9o2YfpG+2VOLpc0GAAoJgY1XN8
P/gumbLEpFvoBZ5xLIW8
=KCgk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
Add reverse scaling function for PMIC5 Gen2 ADC_TM, to convert
temperature to raw ADC code, for setting thresholds for
thermistor channels.
Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/1648991869-20899-3-git-send-email-quic_jprakash@quicinc.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Some sigma-delta chips support sampling of multiple
channels in continuous mode.
When the operating with more than one channel enabled,
the channel sequencer cycles through the enabled channels
in sequential order, from first channel to the last one.
If a channel is disabled, it is skipped by the sequencer.
If more than one channel is used in continuous mode,
instruct the device to append the status to the SPI transfer
(1 extra byte) every time we receive a sample.
All sigma-delta chips possessing a sampling sequencer have
this ability. Inside the status register there will be
the number of the converted channel. In this way, even
if the CPU won't keep up with the sampling rate, it won't
send to userspace wrong channel samples.
When multiple channels are enabled in continuous mode,
the device needs to perform a measurement on all slots
before we can push to userspace the sample.
If, during sequencing and data reading, a channel measurement
is lost, a desync occurred. In this case, ad_sigma_delta drops
the incomplete sample and waits for the device to send the
measurement on the first active slot.
Co-developed-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220322105029.86389-5-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since all AD Sigma-Delta drivers now use the
devm_ad_sd_setup_buffer_and_trigger() function, we can remove the old
ad_sd_{setup,cleanup}_buffer_and_trigger() functions.
This way we can discourage new drivers that use the ad_sigma_delta
lib-driver to use these (older functions).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-13-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a version of ad_sd_setup_buffer_and_trigger() with all underlying
functions (that are used) being replaced with their device-managed
variants.
One thing to take care here is with {devm_}iio_trigger_alloc(), where both
functions take a parent-device object as the first parameter.
To make sure nothing quirky is happening, the devm_ad_sd_probe_trigger()
function is checking that the provided 'dev' reference is the same as the
one stored on the 'struct ad_sigma_delta' driver data.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-6-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The channels are of type iio_chan_spec, not axi_adc_chan_spec. They were in
some earlier version, but forgot to rename in the doc-string.
Fixes: ef04070692 ("iio: adc: adi-axi-adc: add support for AXI ADC IP core")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210219090134.48057-1-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Thermal Monitoring part of PMIC5. This part is closely
coupled with ADC, using it's channels directly. ADC-TM support
generating interrupts on ADC value crossing low or high voltage bounds,
which is used to support thermal trip points.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205000118.493610-3-dmitry.baryshkov@linaro.org
qcom_vadc7_scale_hw_calib_die_temp() uses a table format different from
the rest of volt/temp conversion functions in this file. Also the
conversion functions results in non-monothonic values conversion, which
seems wrong.
Rewrite qcom_vadc7_scale_hw_calib_die_temp() to use
qcom_vadc_map_voltage_temp() directly, like the rest of conversion
functions do.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-10-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
struct vadc_map_pt is not used outside of qcom-vadc-common.c, so move it
there from the global header file.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-9-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
qcom-vadc-common module will be used by ADC thermal monitoring driver,
so move it to global include dir.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-6-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use a heap allocated memory for the SPI transfer buffer. Using stack memory
can corrupt stack memory when using DMA on some systems.
This change moves the buffer from the stack of the trigger handler call to
the heap of the buffer of the state struct. The size increases takes into
account the alignment for the timestamp, which is 8 bytes.
The 'data' buffer is split into 'tx_buf' and 'rx_buf', to make a clearer
separation of which part of the buffer should be used for TX & RX.
Fixes: af3008485e ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201124123807.19717-1-alexandru.ardelean@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change adds support for the Analog Devices Generic AXI ADC IP core.
The IP core is used for interfacing with analog-to-digital (ADC) converters
that require either a high-speed serial interface (JESD204B/C) or a source
synchronous parallel interface (LVDS/CMOS).
Usually, some other interface type (i.e SPI) is used as a control interface
for the actual ADC, while the IP core (controlled via this driver), will
interface to the data-lines of the ADC and handle the streaming of data
into memory via DMA.
Because of this, the AXI ADC driver needs the other SPI-ADC driver to
register with it. The SPI-ADC needs to be register via the SPI framework,
while the AXI ADC registers as a platform driver. The two cannot be ordered
in a hierarchy as both drivers have their own registers, and trying to
organize this [in a hierarchy becomes] problematic when trying to map
memory/registers.
There are some modes where the AXI ADC can operate as standalone ADC, but
those will be implemented at a later point in time.
DocLink: https://wiki.analog.com/resources/fpga/docs/axi_adc_ip
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that all channel SigmaDelta IIO channel macros have been localized,
remove the generic ones.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this patch the ad_sigma_delta implementation hardcoded
the irq trigger type to low, assuming that all Sigma-Delta ADCs
have the same interrupt-type.
This patch allows all drivers using the ad_sigma_delta layer to set the
irq trigger type to the one specified in the datasheet.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch exports the ad_sd_calibrate function in order to be able to
call it from outside ad_sigma_delta.
There are cases where the option to calibrate one channel at a time is
necessary (ex. system calibration for zero scale and full scale).
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For devices from the SigmaDelta family we need to keep CS low when doing a
conversion, since the device will use the MISO line as a interrupt to
indicate that the conversion is complete.
This is why the driver locks the SPI bus and when the SPI bus is locked
keeps as long as a conversion is going on. The current implementation gets
one small detail wrong though. CS is only de-asserted after the SPI bus is
unlocked. This means it is possible for a different SPI device on the same
bus to send a message which would be wrongfully be addressed to the
SigmaDelta device as well. Make sure that the last SPI transfer that is
done while holding the SPI bus lock de-asserts the CS signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <Alexandru.Ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some newer devices from the Sigma-Delta ADC family do have their data
register at a different address than the current default address. Add a
parameter to the ad_sigma_delta_info struct which allows to override the
default address.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix the following sparse warnings:
CHECK drivers/iio/adc/stm32-dfsdm-adc.c
symbol 'stm32_dfsdm_get_buff_cb' was not declared. Should it be static?
symbol 'stm32_dfsdm_release_buff_cb' was not declared. Should it be static?
BTW, move interrupt.h to sort headers alphabetically.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The `ad7780` driver does not implement setting/getting the sampling
frequency.
For the ad7780/ad7781 devices, the control is done via an external pin,
and the ad7170/ad7171 devices have a fixed sampling rate (so, no control).
For these devices, and similar other that may be added later on,
a AD_SD_CHANNEL_NO_SAMPLE_FREQ() macro has been added, which doesn't set
the IIO_CHAN_INFO_SAMP_FREQ flag.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This code offers a way to handle PDM audio microphones in
ASOC framework. Audio driver should use consumer API.
A specific management is implemented for DMA, with a
callback, to allows to handle audio buffers efficiently.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since most of the SD ADCs have the option of reseting the serial
interface by sending a number of SCLKs with CS = 0 and DIN = 1,
a dedicated function that can do this is usefull.
Needed for the patch: iio: ad7793: Fix the serial interface reset
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver predates the availability of IIO_CHAN_INFO_SAMP_FREQ
attribute wherein usage has some advantages like it can be accessed by
in-kernel consumers as well as reduces the code size.
Therefore, use IIO_CHAN_INFO_SAMP_FREQ to implement the
sampling_frequency attribute instead of using IIO_DEV_ATTR_SAMP_FREQ()
macro.
Move code from the functions associated with IIO_DEV_ATTR_SAMP_FREQ()
into respective read and write hooks with the mask set to
IIO_CHAN_INFO_SAMP_FREQ.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Most devices from the Analog Devices Sigma Delta family use a similar scheme for
communication with the device. This includes register access, as well as trigger
handling. But each device sub-family has different features and different
register layouts (some even have no registers at all) and thus it is impractical
to try to support all of the devices by the same driver. This patch adds a
common base library for Sigma Delta converter devices. It will be used by
individual drivers.
This code is mostly based on the three existing Sigma Delta drivers the AD7192,
AD7780 and AD7793, but has been improved for more robustness and flexibility.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Linus Torvalds