DWC3 can tell us which phase of a setup transfer
we're getting into. Let's decode it from the event
to make it easier to debug.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There was a typo when generating endpoint name which
would be very confusing when debugging. Fix it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for endpoint commands, let's have a
single trace output for the command and its
status. This will improve trace readability
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of printing command's status with a separate
trace printout, let's print it within a single call.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Debugfs init failure is not so important. We can continue our job on
this failure. Also no break need for debugfs_create_file call failure.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[felipe.balbi@linux.intel.com :
- remove out-of-memory message, we get that from OOM.
- switch dev_err() to dev_dbg() ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we're debugging hard-to-reproduce and time-sensitive
use cases, printk() poses too much overhead. That's when
the kernel's tracing infrastructure comes into play.
This patch implements a few initial tracepoints for the
dwc3 driver. More traces can be added as necessary in order
to ease the task of debugging dwc3.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Those functions are only using within debugging
messages, grouping them into debug.h makes sense.
While at that, also add missing multiple inclusion
guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a Linux-only driver which makes use
of GPL-only symbols. It makes no sense to
maintain Dual BSD/GPL licensing for this driver.
Considering that the amount of work to use this
driver in any different operating system would likely
be as large as developing the driver from scratch and
considering that we depend on GPL-only symbols, we
will switch over to a GPL v2-only license.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some people think that this line is not compatible with the GPL. The
statement was required due to the Buenos Aires Convention and is now
deprecated. I remove it because it is said that it is pointless nowdays.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.
Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.
The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.
More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.
While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.
[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Felipe Balbi