This test verifies whether the encapsulated packets have the correct
configured TTL. It does so by sending ICMP packets through the test
topology and mirroring them to a gretap netdevice. On a busy host
however, more than just the test ICMP packets may end up flowing
through the topology, get mirrored, and counted. This leads to
potential spurious failures as the test observes much more mirrored
packets than the sent test packets, and assumes a bug.
Fix this by tightening up the mirror action match. Change it from
matchall to a flower classifier matching on ICMP packets specifically.
Fixes: 45315673e0 ("selftests: forwarding: Test changes in mirror-to-gretap")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uwe reports:
"Most PHYs signal WoL using an interrupt. So disabling interrupts [at
shutdown] breaks WoL at least on PHYs covered by the marvell driver."
Discussing with Ioana, the problem which was trying to be solved was:
"The board in question is a LS1021ATSN which has two AR8031 PHYs that
share an interrupt line. In case only one of the PHYs is probed and
there are pending interrupts on the PHY#2 an IRQ storm will happen
since there is no entity to clear the interrupt from PHY#2's registers.
PHY#1's driver will get stuck in .handle_interrupt() indefinitely."
Further confirmation that "the two AR8031 PHYs are on the same MDIO
bus."
With WoL using interrupts to wake the system, in such a case, the
system will begin booting with an asserted interrupt. Thus, we need to
cope with an interrupt asserted during boot.
Solve this instead by disabling interrupts during PHY probe. This will
ensure in Ioana's situation that both PHYs of the same type sharing an
interrupt line on a common MDIO bus will have their interrupt outputs
disabled when the driver probes the device, but before we hook in any
interrupt handlers - thus avoiding the interrupt storm.
A better fix would be for platform firmware to disable the interrupting
devices at source during boot, before control is handed to the kernel.
Fixes: e2f016cf77 ("net: phy: add a shutdown procedure")
Link: 20230804071757.383971-1-u.kleine-koenig@pengutronix.de
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reference of pdev->dev is taken by of_find_device_by_node, so
it should be released when not need anymore.
Fixes: 7dc54d3b8d ("net: pcs: add Renesas MII converter driver")
Signed-off-by: Xiang Yang <xiangyang3@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 25266128fe ("virtio-net: fix race between set queues and
probe") tries to fix the race between set queues and probe by calling
_virtnet_set_queues() before DRIVER_OK is set. This violates virtio
spec. Fixing this by setting queues after virtio_device_ready().
Note that rtnl needs to be held for userspace requests to change the
number of queues. So we are serialized in this way.
Fixes: 25266128fe ("virtio-net: fix race between set queues and probe")
Reported-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross merge x86 fixes to fix clang linking errors:
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:221: at least one side of the expression must be absolute
These will hopefully be downstream by the time we ship
the next batch of fixes.
* 'x86/bugs' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Move gds_ucode_mitigated() declaration to header
x86/speculation: Add cpu_show_gds() prototype
driver core: cpu: Make cpu_show_not_affected() static
x86/srso: Fix build breakage with the LLVM linker
Documentation/srso: Document IBPB aspect and fix formatting
driver core: cpu: Unify redundant silly stubs
Documentation/hw-vuln: Unify filename specification in index
Link: https://lore.kernel.org/all/CAHk-=wj_b+FGTnevQSBAtCWuhCk=0oQ_THvthBW2hzqpOTLFmg@mail.gmail.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Still trending up in size but the good news is that the "current"
regressions are resolved, AFAIK.
We're getting weirdly many fixes for Wake-on-LAN and suspend/resume
handling on embedded this week (most not merged yet), not sure why.
But those are all for older bugs.
Current release - regressions:
- tls: set MSG_SPLICE_PAGES consistently when handing encrypted
data over to TCP
Current release - new code bugs:
- eth: mlx5: correct IDs on VFs internal to the device (IPU)
Previous releases - regressions:
- phy: at803x: fix WoL support / reporting on AR8032
- bonding: fix incorrect deletion of ETH_P_8021AD protocol VID
from slaves, leading to BUG_ON()
- tun: prevent tun_build_skb() from exceeding the packet size limit
- wifi: rtw89: fix 8852AE disconnection caused by RX full flags
- eth/PCI: enetc: fix probing after 6fffbc7ae1 ("PCI: Honor
firmware's device disabled status"), keep PCI devices around
even if they are disabled / not going to be probed to be
able to apply quirks on them
- eth: prestera: fix handling IPv4 routes with nexthop IDs
Previous releases - always broken:
- netfilter: re-work garbage collection to avoid races between
user-facing API and timeouts
- tunnels: fix generating ipv4 PMTU error on non-linear skbs
- nexthop: fix infinite nexthop bucket dump when using maximum
nexthop ID
- wifi: nl80211: fix integer overflow in nl80211_parse_mbssid_elems()
Misc:
- unix: use consistent error code in SO_PEERPIDFD
- ipv6: adjust ndisc_is_useropt() to include PREFIX_INFO,
in prep for upcoming IETF RFC
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmTVMSsACgkQMUZtbf5S
Irul3g//RlSANV/MWkiDmHIS5IhqkVWbvjGhFXFfdqZPH4gfgcX9VrsMuxgNM1Xu
YXGx+rIu408qNNkVG2hpFMxPerRiqVB/XsH1TxRr0Mi6AMFoKGXS+cGwzSOaoMQj
FYlcC6j2SnQ9N4I0qQuKOSOffyvyxrx/l9ozpVXsbGsOic1k6j1Ipwtf3+WP7dEe
kkAPUlsQPdCIhMyQdK3X4xI1PGLtAXFgY3VV9bZ7u99l7QBwmconkl3GHq/xnPa8
Uyll005ThyYce0c4EPVcrY1YBXyY0LjOBIRtiTFAk6CMWc0Su8Ug/i4+K2KTq0eh
yjqqHkpR//ruLgtAXBLLE9mxma8448vmmex/cSLIBaMAttlnj9n2LvCqvbzNfTZA
ssnKO4D3HhoQvHqbeOOW6VzVX7XyhomOvQXihfdLUs9u2tKE3nQoU+QCnrnIUXZO
VF5/ubCERRdZDPQ1SSAktimlC0R1qVL7JPMRaQF0aW5xByabbEWwMaNiwkYQOh2o
w2KsbhM/vWyd+5JB412LrNsEgK1BV6WjgwzC+27YQ7QD/JxUZBUghL0ps2jgU2Lu
d4YdbBOgYz+xyUBPByeYzcac0SIeMkB/UEcaO54ySWU8GcWYLt4KXwydUq/cXlw0
rUDCO5bikMxmygLKtnTSwmwvGbGByEXbGvVKwUwNPqTnR+vPIbM=
=NZgp
-----END PGP SIGNATURE-----
Merge tag 'net-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, wireless and bpf.
Still trending up in size but the good news is that the "current"
regressions are resolved, AFAIK.
We're getting weirdly many fixes for Wake-on-LAN and suspend/resume
handling on embedded this week (most not merged yet), not sure why.
But those are all for older bugs.
Current release - regressions:
- tls: set MSG_SPLICE_PAGES consistently when handing encrypted data
over to TCP
Current release - new code bugs:
- eth: mlx5: correct IDs on VFs internal to the device (IPU)
Previous releases - regressions:
- phy: at803x: fix WoL support / reporting on AR8032
- bonding: fix incorrect deletion of ETH_P_8021AD protocol VID from
slaves, leading to BUG_ON()
- tun: prevent tun_build_skb() from exceeding the packet size limit
- wifi: rtw89: fix 8852AE disconnection caused by RX full flags
- eth/PCI: enetc: fix probing after 6fffbc7ae1 ("PCI: Honor
firmware's device disabled status"), keep PCI devices around even
if they are disabled / not going to be probed to be able to apply
quirks on them
- eth: prestera: fix handling IPv4 routes with nexthop IDs
Previous releases - always broken:
- netfilter: re-work garbage collection to avoid races between
user-facing API and timeouts
- tunnels: fix generating ipv4 PMTU error on non-linear skbs
- nexthop: fix infinite nexthop bucket dump when using maximum
nexthop ID
- wifi: nl80211: fix integer overflow in nl80211_parse_mbssid_elems()
Misc:
- unix: use consistent error code in SO_PEERPIDFD
- ipv6: adjust ndisc_is_useropt() to include PREFIX_INFO, in prep for
upcoming IETF RFC"
* tag 'net-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
net: hns3: fix strscpy causing content truncation issue
net: tls: set MSG_SPLICE_PAGES consistently
ibmvnic: Ensure login failure recovery is safe from other resets
ibmvnic: Do partial reset on login failure
ibmvnic: Handle DMA unmapping of login buffs in release functions
ibmvnic: Unmap DMA login rsp buffer on send login fail
ibmvnic: Enforce stronger sanity checks on login response
net: mana: Fix MANA VF unload when hardware is unresponsive
netfilter: nf_tables: remove busy mark and gc batch API
netfilter: nft_set_hash: mark set element as dead when deleting from packet path
netfilter: nf_tables: adapt set backend to use GC transaction API
netfilter: nf_tables: GC transaction API to avoid race with control plane
selftests/bpf: Add sockmap test for redirecting partial skb data
selftests/bpf: fix a CI failure caused by vsock sockmap test
bpf, sockmap: Fix bug that strp_done cannot be called
bpf, sockmap: Fix map type error in sock_map_del_link
xsk: fix refcount underflow in error path
ipv6: adjust ndisc_is_useropt() to also return true for PIO
selftests: forwarding: bridge_mdb: Make test more robust
selftests: forwarding: bridge_mdb_max: Fix failing test with old libnet
...
hns3_dbg_fill_content()/hclge_dbg_fill_content() is aim to integrate some
items to a string for content, and we add '\n' and '\0' in the last
two bytes of content.
strscpy() will add '\0' in the last byte of destination buffer(one of
items), it result in finishing content print ahead of schedule and some
dump content truncation.
One Error log shows as below:
cat mac_list/uc
UC MAC_LIST:
Expected:
UC MAC_LIST:
FUNC_ID MAC_ADDR STATE
pf 00:2b:19:05:03:00 ACTIVE
The destination buffer is length-bounded and not required to be
NUL-terminated, so just change strscpy() to memcpy() to fix it.
Fixes: 1cf3d5567f ("net: hns3: fix strncpy() not using dest-buf length as length issue")
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20230809020902.1941471-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We used to change the flags for the last segment, because
non-last segments had the MSG_SENDPAGE_NOTLAST flag set.
That flag is no longer a thing so remove the setting.
Since flags most likely don't have MSG_SPLICE_PAGES set
this avoids passing parts of the sg as splice and parts
as non-splice. Before commit under Fixes we'd have called
tcp_sendpage() which would add the MSG_SPLICE_PAGES.
Why this leads to trouble remains unclear but Tariq
reports hitting the WARN_ON(!sendpage_ok()) due to
page refcount of 0.
Fixes: e117dcfd64 ("tls: Inline do_tcp_sendpages()")
Reported-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/all/4c49176f-147a-4283-f1b1-32aac7b4b996@gmail.com/
Tested-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20230808180917.1243540-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KNf7
-----END PGP SIGNATURE-----
Merge tag 'nf-23-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The existing attempt to resolve races between control plane and GC work
is error prone, as reported by Bien Pham <phamnnb@sea.com>, some places
forgot to call nft_set_elem_mark_busy(), leading to double-deactivation
of elements.
This series contains the following patches:
1) Do not skip expired elements during walk otherwise elements might
never decrement the reference counter on data, leading to memleak.
2) Add a GC transaction API to replace the former attempt to deal with
races between control plane and GC. GC worker sets on NFT_SET_ELEM_DEAD_BIT
on elements and it creates a GC transaction to remove the expired
elements, GC transaction could abort in case of interference with
control plane and retried later (GC async). Set backends such as
rbtree and pipapo also perform GC from control plane (GC sync), in
such case, element deactivation and removal is safe because mutex
is held then collected elements are released via call_rcu().
3) Adapt existing set backends to use the GC transaction API.
4) Update rhash set backend to set on _DEAD bit to report deleted
elements from datapath for GC.
5) Remove old GC batch API and the NFT_SET_ELEM_BUSY_BIT.
* tag 'nf-23-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: remove busy mark and gc batch API
netfilter: nft_set_hash: mark set element as dead when deleting from packet path
netfilter: nf_tables: adapt set backend to use GC transaction API
netfilter: nf_tables: GC transaction API to avoid race with control plane
netfilter: nf_tables: don't skip expired elements during walk
====================
Link: https://lore.kernel.org/r/20230810070830.24064-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRdM/uy1Ege0+EN1fNar9k/UBDW4wUCZNRuIQAKCRBar9k/UBDW
4++9AP9ymOcPOKTKdQwZ6cnq3vkmvN37H6teufTyM8vsCha9NAD+OQE+vg1304RM
aETtG6d5Nb+byIHZGJrdUyT7g9jRzgw=
=qr/C
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Martin KaFai Lau says:
====================
pull-request: bpf 2023-08-09
We've added 5 non-merge commits during the last 7 day(s) which contain
a total of 6 files changed, 102 insertions(+), 8 deletions(-).
The main changes are:
1) A bpf sockmap memleak fix and a fix in accessing the programs of
a sockmap under the incorrect map type from Xu Kuohai.
2) A refcount underflow fix in xsk from Magnus Karlsson.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Add sockmap test for redirecting partial skb data
selftests/bpf: fix a CI failure caused by vsock sockmap test
bpf, sockmap: Fix bug that strp_done cannot be called
bpf, sockmap: Fix map type error in sock_map_del_link
xsk: fix refcount underflow in error path
====================
Link: https://lore.kernel.org/r/20230810055303.120917-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a login request fails, the recovery process should be protected
against parallel resets. It is a known issue that freeing and
registering CRQ's in quick succession can result in a failover CRQ from
the VIOS. Processing a failover during login recovery is dangerous for
two reasons:
1. This will result in two parallel initialization processes, this can
cause serious issues during login.
2. It is possible that the failover CRQ is received but never executed.
We get notified of a pending failover through a transport event CRQ.
The reset is not performed until a INIT CRQ request is received.
Previously, if CRQ init fails during login recovery, then the ibmvnic
irq is freed and the login process returned error. If failover_pending
is true (a transport event was received), then the ibmvnic device
would never be able to process the reset since it cannot receive the
CRQ_INIT request due to the irq being freed. This leaved the device
in a inoperable state.
Therefore, the login failure recovery process must be hardened against
these possible issues. Possible failovers (due to quick CRQ free and
init) must be avoided and any issues during re-initialization should be
dealt with instead of being propagated up the stack. This logic is
similar to that of ibmvnic_probe().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-5-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Perform a partial reset before sending a login request if any of the
following are true:
1. If a previous request times out. This can be dangerous because the
VIOS could still receive the old login request at any point after
the timeout. Therefore, it is best to re-register the CRQ's and
sub-CRQ's before retrying.
2. If the previous request returns an error that is not described in
PAPR. PAPR provides procedures if the login returns with partial
success or aborted return codes (section L.5.1) but other values
do not have a defined procedure. Previously, these conditions
just returned error from the login function rather than trying
to resolve the issue.
This can cause further issues since most callers of the login
function are not prepared to handle an error when logging in. This
improper cleanup can lead to the device being permanently DOWN'd.
For example, if the VIOS believes that the device is already logged
in then it will return INVALID_STATE (-7). If we never re-register
CRQ's then it will always think that the device is already logged
in. This leaves the device inoperable.
The partial reset involves freeing the sub-CRQs, freeing the CRQ then
registering and initializing a new CRQ and sub-CRQs. This essentially
restarts all communication with VIOS to allow for a fresh login attempt
that will be unhindered by any previous failed attempts.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-4-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rather than leaving the DMA unmapping of the login buffers to the
login response handler, move this work into the login release functions.
Previously, these functions were only used for freeing the allocated
buffers. This could lead to issues if there are more than one
outstanding login buffer requests, which is possible if a login request
times out.
If a login request times out, then there is another call to send login.
The send login function makes a call to the login buffer release
function. In the past, this freed the buffers but did not DMA unmap.
Therefore, the VIOS could still write to the old login (now freed)
buffer. It is for this reason that it is a good idea to leave the DMA
unmap call to the login buffers release function.
Since the login buffer release functions now handle DMA unmapping,
remove the duplicate DMA unmapping in handle_login_rsp().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-3-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the LOGIN CRQ fails to send then we must DMA unmap the response
buffer. Previously, if the CRQ failed then the memory was freed without
DMA unmapping.
Fixes: c98d9cc417 ("ibmvnic: send_login should check for crq errors")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure that all offsets in a login response buffer are within the size
of the allocated response buffer. Any offsets or lengths that surpass
the allocation are likely the result of an incomplete response buffer.
In these cases, a full reset is necessary.
When attempting to login, the ibmvnic device will allocate a response
buffer and pass a reference to the VIOS. The VIOS will then send the
ibmvnic device a LOGIN_RSP CRQ to signal that the buffer has been filled
with data. If the ibmvnic device does not get a response in 20 seconds,
the old buffer is freed and a new login request is sent. With 2
outstanding requests, any LOGIN_RSP CRQ's could be for the older
login request. If this is the case then the login response buffer (which
is for the newer login request) could be incomplete and contain invalid
data. Therefore, we must enforce strict sanity checks on the response
buffer values.
Testing has shown that the `off_rxadd_buff_size` value is filled in last
by the VIOS and will be the smoking gun for these circumstances.
Until VIOS can implement a mechanism for tracking outstanding response
buffers and a method for mapping a LOGIN_RSP CRQ to a particular login
response buffer, the best ibmvnic can do in this situation is perform a
full reset.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When unloading the MANA driver, mana_dealloc_queues() waits for the MANA
hardware to complete any inflight packets and set the pending send count
to zero. But if the hardware has failed, mana_dealloc_queues()
could wait forever.
Fix this by adding a timeout to the wait. Set the timeout to 120 seconds,
which is a somewhat arbitrary value that is more than long enough for
functional hardware to complete any sends.
Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Link: https://lore.kernel.org/r/1691576525-24271-1-git-send-email-schakrabarti@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The declaration got placed in the .c file of the caller, but that
causes a warning for the definition:
arch/x86/kernel/cpu/bugs.c:682:6: error: no previous prototype for 'gds_ucode_mitigated' [-Werror=missing-prototypes]
Move it to a header where both sides can observe it instead.
Fixes: 81ac7e5d74 ("KVM: Add GDS_NO support to KVM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/all/20230809130530.1913368-2-arnd%40kernel.org
The newly added function has two definitions but no prototypes:
drivers/base/cpu.c:605:16: error: no previous prototype for 'cpu_show_gds' [-Werror=missing-prototypes]
Add a declaration next to the other ones for this file to avoid the
warning.
Fixes: 8974eb5882 ("x86/speculation: Add Gather Data Sampling mitigation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/all/20230809130530.1913368-1-arnd%40kernel.org
The assertion added to verify the difference in bits set of the
addresses of srso_untrain_ret_alias() and srso_safe_ret_alias() would fail
to link in LLVM's ld.lld linker with the following error:
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:210: at least one side of
the expression must be absolute
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:211: at least one side of
the expression must be absolute
Use ABSOLUTE to evaluate the expression referring to at least one of the
symbols so that LLD can evaluate the linker script.
Also, add linker version info to the comment about XOR being unsupported
in either ld.bfd or ld.lld until somewhat recently.
Fixes: fb3bd914b3 ("x86/srso: Add a Speculative RAS Overflow mitigation")
Closes: https://lore.kernel.org/llvm/CA+G9fYsdUeNu-gwbs0+T6XHi4hYYk=Y9725-wFhZ7gJMspLDRA@mail.gmail.com/
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Daniel Kolesa <daniel@octaforge.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Suggested-by: Sven Volkinsfeld <thyrc@gmx.net>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://github.com/ClangBuiltLinux/linux/issues/1907
Link: https://lore.kernel.org/r/20230809-gds-v1-1-eaac90b0cbcc@google.com
Add a note about the dependency of the User->User mitigation on the
previous Spectre v2 IBPB selection.
Make the layout moar pretty.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230809102700.29449-4-bp@alien8.de
Make them all a weak function, aliasing to a single function which
issues the "Not affected" string.
No functional changes.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Nikolay Borisov <nik.borisov@suse.com>
Link: https://lore.kernel.org/r/20230809102700.29449-3-bp@alien8.de
Most of the index.rst files in Documentation/ refer to other rst files
without their file extension in the name. Do that here too.
No functional changes.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230809102700.29449-2-bp@alien8.de
Set on the NFT_SET_ELEM_DEAD_BIT flag on this element, instead of
performing element removal which might race with an ongoing transaction.
Enable gc when dynamic flag is set on since dynset deletion requires
garbage collection after this patch.
Fixes: d0a8d877da ("netfilter: nft_dynset: support for element deletion")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use the GC transaction API to replace the old and buggy gc API and the
busy mark approach.
No set elements are removed from async garbage collection anymore,
instead the _DEAD bit is set on so the set element is not visible from
lookup path anymore. Async GC enqueues transaction work that might be
aborted and retried later.
rbtree and pipapo set backends does not set on the _DEAD bit from the
sync GC path since this runs in control plane path where mutex is held.
In this case, set elements are deactivated, removed and then released
via RCU callback, sync GC never fails.
Fixes: 3c4287f620 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Fixes: 8d8540c4f5 ("netfilter: nft_set_rbtree: add timeout support")
Fixes: 9d0982927e ("netfilter: nft_hash: add support for timeouts")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The set types rhashtable and rbtree use a GC worker to reclaim memory.
From system work queue, in periodic intervals, a scan of the table is
done.
The major caveat here is that the nft transaction mutex is not held.
This causes a race between control plane and GC when they attempt to
delete the same element.
We cannot grab the netlink mutex from the work queue, because the
control plane has to wait for the GC work queue in case the set is to be
removed, so we get following deadlock:
cpu 1 cpu2
GC work transaction comes in , lock nft mutex
`acquire nft mutex // BLOCKS
transaction asks to remove the set
set destruction calls cancel_work_sync()
cancel_work_sync will now block forever, because it is waiting for the
mutex the caller already owns.
This patch adds a new API that deals with garbage collection in two
steps:
1) Lockless GC of expired elements sets on the NFT_SET_ELEM_DEAD_BIT
so they are not visible via lookup. Annotate current GC sequence in
the GC transaction. Enqueue GC transaction work as soon as it is
full. If ruleset is updated, then GC transaction is aborted and
retried later.
2) GC work grabs the mutex. If GC sequence has changed then this GC
transaction lost race with control plane, abort it as it contains
stale references to objects and let GC try again later. If the
ruleset is intact, then this GC transaction deactivates and removes
the elements and it uses call_rcu() to destroy elements.
Note that no elements are removed from GC lockless path, the _DEAD bit
is set and pointers are collected. GC catchall does not remove the
elements anymore too. There is a new set->dead flag that is set on to
abort the GC transaction to deal with set->ops->destroy() path which
removes the remaining elements in the set from commit_release, where no
mutex is held.
To deal with GC when mutex is held, which allows safe deactivate and
removal, add sync GC API which releases the set element object via
call_rcu(). This is used by rbtree and pipapo backends which also
perform garbage collection from control plane path.
Since element removal from sets can happen from control plane and
element garbage collection/timeout, it is necessary to keep the set
structure alive until all elements have been deactivated and destroyed.
We cannot do a cancel_work_sync or flush_work in nft_set_destroy because
its called with the transaction mutex held, but the aforementioned async
work queue might be blocked on the very mutex that nft_set_destroy()
callchain is sitting on.
This gives us the choice of ABBA deadlock or UaF.
To avoid both, add set->refs refcount_t member. The GC API can then
increment the set refcount and release it once the elements have been
free'd.
Set backends are adapted to use the GC transaction API in a follow up
patch entitled:
("netfilter: nf_tables: use gc transaction API in set backends")
This is joint work with Florian Westphal.
Fixes: cfed7e1b1f ("netfilter: nf_tables: add set garbage collection helpers")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
-----BEGIN PGP SIGNATURE-----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=gGNY
-----END PGP SIGNATURE-----
Merge tag '6.5-rc5-ksmbd-server' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
"Two ksmbd server fixes, both also for stable:
- improve buffer validation when multiple EAs returned
- missing check for command payload size"
* tag '6.5-rc5-ksmbd-server' of git://git.samba.org/ksmbd:
ksmbd: fix wrong next length validation of ea buffer in smb2_set_ea()
ksmbd: validate command request size
- Revert a patch that unconditionally resolved addresses to inlines in
callchains, something that was done before when DWARF mode was asked
for, but could as well be done when just frame pointers (the default)
was selected. This enriches the callchains with inlines but the way to
resolve it is gross right now, relying on addr2line, and even if we come
up with an efficient way of processing all the associated DWARF info for
a big file as vmlinux is, this has to be something people opt-in, as it
will still result in overheads, so revert it until we get this done in a
saner way.
- Update the x86 msr-index.h header with the kernel original, no change
in tooling output, just addresses a tools/perf build warning.
- Resolve a regression where special "tool events", such as
"duration_time" were being presented for all CPUs, when it only makes
sense to show it for the workload, that is, just once.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCZNP/OAAKCRCyPKLppCJ+
J7cGAQDgNpsAqGk+/Xkk7lPcp8aJ7q+5oaxv8iaGhdblq7V52gD+L2t8sNPQYWE3
sy2QQ+9tsZiONfpdxknsduxoyfE+Vgs=
=CRYB
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v6.5-3-2023-08-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Revert a patch that unconditionally resolved addresses to inlines in
callchains, something that was done before when DWARF mode was asked
for, but could as well be done when just frame pointers (the default)
was selected.
This enriches the callchains with inlines but the way to resolve it
is gross right now, relying on addr2line, and even if we come up with
an efficient way of processing all the associated DWARF info for a
big file as vmlinux is, this has to be something people opt-in, as it
will still result in overheads, so revert it until we get this done
in a saner way.
- Update the x86 msr-index.h header with the kernel original, no change
in tooling output, just addresses a tools/perf build warning.
- Resolve a regression where special "tool events", such as
"duration_time" were being presented for all CPUs, when it only
makes sense to show it for the workload, that is, just once.
* tag 'perf-tools-fixes-for-v6.5-3-2023-08-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf stat: Don't display zero tool counts
tools arch x86: Sync the msr-index.h copy with the kernel sources
Revert "perf report: Append inlines to non-DWARF callchains"
Add a test case to check whether sockmap redirection works correctly
when data length returned by stream_parser is less than skb->len.
In addition, this test checks whether strp_done is called correctly.
The reason is that we returns skb->len - 1 from the stream_parser, so
the last byte in the skb will be held by strp->skb_head. Therefore,
if strp_done is not called to free strp->skb_head, we'll get a memleak
warning.
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20230804073740.194770-5-xukuohai@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
BPF CI has reported the following failure:
Error: #200/79 sockmap_listen/sockmap VSOCK test_vsock_redir
Error: #200/79 sockmap_listen/sockmap VSOCK test_vsock_redir
./test_progs:vsock_unix_redir_connectible:1506: egress: write: Transport endpoint is not connected
vsock_unix_redir_connectible:FAIL:1506
./test_progs:vsock_unix_redir_connectible:1506: ingress: write: Transport endpoint is not connected
vsock_unix_redir_connectible:FAIL:1506
./test_progs:vsock_unix_redir_connectible:1506: egress: write: Transport endpoint is not connected
vsock_unix_redir_connectible:FAIL:1506
./test_progs:vsock_unix_redir_connectible:1514: ingress: recv() err, errno=11
vsock_unix_redir_connectible:FAIL:1514
./test_progs:vsock_unix_redir_connectible:1518: ingress: vsock socket map failed, a != b
vsock_unix_redir_connectible:FAIL:1518
./test_progs:vsock_unix_redir_connectible:1525: ingress: want pass count 1, have 0
It’s because the recv(... MSG_DONTWAIT) syscall in the test case is
called before the queued work sk_psock_backlog() in the kernel finishes
executing. So the data to be read is still queued in psock->ingress_skb
and cannot be read by the user program. Therefore, the non-blocking
recv() reads nothing and reports an EAGAIN error.
So replace recv(... MSG_DONTWAIT) with xrecv_nonblock(), which calls
select() to wait for data to be readable or timeout before calls recv().
Fixes: d61bd8c1fd ("selftests/bpf: add a test case for vsock sockmap")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20230804073740.194770-4-xukuohai@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
strp_done is only called when psock->progs.stream_parser is not NULL,
but stream_parser was set to NULL by sk_psock_stop_strp(), called
by sk_psock_drop() earlier. So, strp_done can never be called.
Introduce SK_PSOCK_RX_ENABLED to mark whether there is strp on psock.
Change the condition for calling strp_done from judging whether
stream_parser is set to judging whether this flag is set. This flag is
only set once when strp_init() succeeds, and will never be cleared later.
Fixes: c0d95d3380 ("bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20230804073740.194770-3-xukuohai@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
sock_map_del_link() operates on both SOCKMAP and SOCKHASH, although
both types have member named "progs", the offset of "progs" member in
these two types is different, so "progs" should be accessed with the
real map type.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20230804073740.194770-2-xukuohai@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Fix a refcount underflow problem reported by syzbot that can happen
when a system is running out of memory. If xp_alloc_tx_descs() fails,
and it can only fail due to not having enough memory, then the error
path is triggered. In this error path, the refcount of the pool is
decremented as it has incremented before. However, the reference to
the pool in the socket was not nulled. This means that when the socket
is closed later, the socket teardown logic will think that there is a
pool attached to the socket and try to decrease the refcount again,
leading to a refcount underflow.
I chose this fix as it involved adding just a single line. Another
option would have been to move xp_get_pool() and the assignment of
xs->pool to after the if-statement and using xs_umem->pool instead of
xs->pool in the whole if-statement resulting in somewhat simpler code,
but this would have led to much more churn in the code base perhaps
making it harder to backport.
Fixes: ba3beec2ec ("xsk: Fix possible crash when multiple sockets are created")
Reported-by: syzbot+8ada0057e69293a05fd4@syzkaller.appspotmail.com
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/r/20230809142843.13944-1-magnus.karlsson@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
The upcoming (and nearly finalized):
https://datatracker.ietf.org/doc/draft-collink-6man-pio-pflag/
will update the IPv6 RA to include a new flag in the PIO field,
which will serve as a hint to perform DHCPv6-PD.
As we don't want DHCPv6 related logic inside the kernel, this piece of
information needs to be exposed to userspace. The simplest option is to
simply expose the entire PIO through the already existing mechanism.
Even without this new flag, the already existing PIO R (router address)
flag (from RFC6275) cannot AFAICT be handled entirely in kernel,
and provides useful information that should be exposed to userspace
(the router's global address, for use by Mobile IPv6).
Also cc'ing stable@ for inclusion in LTS, as while technically this is
not quite a bugfix, and instead more of a feature, it is absolutely
trivial and the alternative is manually cherrypicking into all Android
Common Kernel trees - and I know Greg will ask for it to be sent in via
LTS instead...
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: YOSHIFUJI Hideaki / 吉藤英明 <yoshfuji@linux-ipv6.org>
Cc: stable@vger.kernel.org
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20230807102533.1147559-1-maze@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel says:
====================
selftests: forwarding: Various fixes
Fix various problems with forwarding selftests. See individual patches
for problem description and solution.
====================
Link: https://lore.kernel.org/r/20230808141503.4060661-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some test cases check that the group timer is (or isn't) 0. Instead of
grepping for "0.00" grep for " 0.00" as the former can also match
"260.00" which is the default group membership interval.
Fixes: b6d00da086 ("selftests: forwarding: Add bridge MDB test")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-18-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 8bcfb4ae4d ("selftests: forwarding: Fix failing
tests with old libnet"), old versions of libnet (used by mausezahn) do
not use the "SO_BINDTODEVICE" socket option. For IP unicast packets,
this can be solved by prefixing mausezahn invocations with "ip vrf
exec". However, IP multicast packets do not perform routing and simply
egress the bound device, which does not exist in this case.
Fix by specifying the source and destination MAC of the packet which
will cause mausezahn to use a packet socket instead of an IP socket.
Fixes: 3446dcd7df ("selftests: forwarding: bridge_mdb_max: Add a new selftest")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-17-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 8bcfb4ae4d ("selftests: forwarding: Fix failing
tests with old libnet"), old versions of libnet (used by mausezahn) do
not use the "SO_BINDTODEVICE" socket option. For IP unicast packets,
this can be solved by prefixing mausezahn invocations with "ip vrf
exec". However, IP multicast packets do not perform routing and simply
egress the bound device, which does not exist in this case.
Fix by specifying the source and destination MAC of the packet which
will cause mausezahn to use a packet socket instead of an IP socket.
Fixes: b6d00da086 ("selftests: forwarding: Add bridge MDB test")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-16-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 8bcfb4ae4d ("selftests: forwarding: Fix failing
tests with old libnet"), old versions of libnet (used by mausezahn) do
not use the "SO_BINDTODEVICE" socket option. For IP unicast packets,
this can be solved by prefixing mausezahn invocations with "ip vrf
exec". However, IP multicast packets do not perform routing and simply
egress the bound device, which does not exist in this case.
Fix by specifying the source and destination MAC of the packet which
will cause mausezahn to use a packet socket instead of an IP socket.
Fixes: 8c33266ae2 ("selftests: forwarding: Add layer 2 miss test cases")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-15-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test installs filters that match on various IP fragments (e.g., no
fragment, first fragment) and expects a certain amount of packets to hit
each filter. This is problematic as the filters are not specific enough
and can match IP packets (e.g., IGMP) generated by the stack, resulting
in failures [1].
Fix by making the filters more specific and match on more fields in the
IP header: Source IP, destination IP and protocol.
[1]
# timeout set to 0
# selftests: net/forwarding: tc_tunnel_key.sh
# TEST: tunnel_key nofrag (skip_hw) [FAIL]
# packet smaller than MTU was not tunneled
# INFO: Could not test offloaded functionality
not ok 89 selftests: net/forwarding: tc_tunnel_key.sh # exit=1
Fixes: 533a89b194 ("selftests: forwarding: add tunnel_key "nofrag" test case")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-14-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks that filters that match on source or destination MAC
were only hit once. A host can send more than one packet with a given
source or destination MAC, resulting in failures.
Fix by relaxing the success criterion and instead check that the filters
were not hit zero times. Using tc_check_at_least_x_packets() is also an
option, but it is not available in older kernels.
Fixes: 07e5c75184 ("selftests: forwarding: Introduce tc flower matching tests")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-13-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test relies on 'nc' being the netcat version from the nmap project.
While this seems to be the case on Fedora, it is not the case on Ubuntu,
resulting in failures such as [1].
Fix by explicitly using the 'ncat' utility from the nmap project and the
skip the test in case it is not installed.
[1]
# timeout set to 0
# selftests: net/forwarding: tc_actions.sh
# TEST: gact drop and ok (skip_hw) [ OK ]
# TEST: mirred egress flower redirect (skip_hw) [ OK ]
# TEST: mirred egress flower mirror (skip_hw) [ OK ]
# TEST: mirred egress matchall mirror (skip_hw) [ OK ]
# TEST: mirred_egress_to_ingress (skip_hw) [ OK ]
# nc: invalid option -- '-'
# usage: nc [-46CDdFhklNnrStUuvZz] [-I length] [-i interval] [-M ttl]
# [-m minttl] [-O length] [-P proxy_username] [-p source_port]
# [-q seconds] [-s sourceaddr] [-T keyword] [-V rtable] [-W recvlimit]
# [-w timeout] [-X proxy_protocol] [-x proxy_address[:port]]
# [destination] [port]
# nc: invalid option -- '-'
# usage: nc [-46CDdFhklNnrStUuvZz] [-I length] [-i interval] [-M ttl]
# [-m minttl] [-O length] [-P proxy_username] [-p source_port]
# [-q seconds] [-s sourceaddr] [-T keyword] [-V rtable] [-W recvlimit]
# [-w timeout] [-X proxy_protocol] [-x proxy_address[:port]]
# [destination] [port]
# TEST: mirred_egress_to_ingress_tcp (skip_hw) [FAIL]
# server output check failed
# INFO: Could not test offloaded functionality
not ok 80 selftests: net/forwarding: tc_actions.sh # exit=1
Fixes: ca22da2fbd ("act_mirred: use the backlog for nested calls to mirred ingress")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-12-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MAC Merge cannot be tested with veth pairs, resulting in failures:
# ./ethtool_mm.sh
[...]
TEST: Manual configuration with verification: swp1 to swp2 [FAIL]
Verification did not succeed
Fix by skipping the test when the interfaces do not support MAC Merge.
Fixes: e6991384ac ("selftests: forwarding: add a test for MAC Merge layer")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-11-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Layer 3 hardware stats cannot be used when the underlying interfaces are
veth pairs, resulting in failures:
# ./hw_stats_l3_gre.sh
TEST: ping gre flat [ OK ]
TEST: Test rx packets: [FAIL]
Traffic not reflected in the counter: 0 -> 0
TEST: Test tx packets: [FAIL]
Traffic not reflected in the counter: 0 -> 0
Fix by skipping the test when used with veth pairs.
Fixes: 813f97a268 ("selftests: forwarding: Add a tunnel-based test for L3 HW stats")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-10-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ethtool extended state cannot be tested with veth pairs, resulting in
failures:
# ./ethtool_extended_state.sh
TEST: Autoneg, No partner detected [FAIL]
Expected "Autoneg", got "Link detected: no"
[...]
Fix by skipping the test when used with veth pairs.
Fixes: 7d10bcce98 ("selftests: forwarding: Add tests for ethtool extended state")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-9-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata