The commit fbf68229ff ("net: stmmac: unify registers dumps methods")
in the Linux kernel modified the register dump to store the DMA registers
at the DMA register offset (0x1000) but ethtool (stmmac.c) looks for the
DMA registers after the MAC registers which is offset 55.
This patch copies the DMA registers from the higher offset to the offset
where ethtool expects them.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unconditional reset dwmac before HW init if reset controller is present.
In existing implementation we reset dwmac only after second module
probing:
(module load -> unload -> load again [reset happens])
Now we reset dwmac at every module load:
(module load [reset happens] -> unload -> load again [reset happens])
Also some reset controllers have only reset callback instead of
assert + deassert callbacks pair, so handle this case.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate array route_possibilities on the stack but make it
static const. Makes the object code a little smaller by 85 bytes:
Before:
text data bss dec hex filename
9901 2448 0 12349 303d dwmac4_core.o
After:
text data bss dec hex filename
9760 2504 0 12264 2fe8 dwmac4_core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since internal phy-mode is reserved for non-xMII protocol we cannot use
it with dwmac-sun8i.
Furthermore, all DT patchs which comes with this patch were cleaned, so
the current state is broken.
This reverts commit 1c2fa5f846 ("net: stmmac: support future possible different internal phy mode")
Fixes: 1c2fa5f846 ("net: stmmac: support future possible different internal phy mode")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'alloc_dma_[rt]x_desc_resources()' functions look very close.
Remove a useless initialization and use the same label name for error
handling path in order to get them even closer.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the first 'kmalloc_array' within the loop fails, we should free what
as already been allocated, as done in all other error handling path.
Fixes: ce736788e8 ("net: stmmac: adding multiple buffers for TX")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the first 'kmalloc_array' within the loop fails, we should free what
as already been allocated, as done in all other error handling path.
Fixes: 54139cf3bb ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version 3.70a of the Designware has additional DMA registers so
add those to the ethtool DMA Register dump.
Offset 9 - Receive Interrupt Watchdog Timer Register
Offset 10 - AXI Bus Mode Register
Offset 11 - AHB or AXI Status Register
Offset 22 - HW Feature Register
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current way to find if the phy is internal is to compare DT phy-mode
and emac_variant/internal_phy.
But it will negate a possible future SoC where an external PHY use the
same phy mode than the internal one.
By using phy-mode = "internal" we permit to have an external PHY with
the same mode than the internal one.
Reported-by: André Przywara <andre.przywara@arm.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions dwmac4_dma_init_rx_chan, dwmac4_dma_init_tx_chan and
dwmac4_dma_init_channel do not need to be in global scope, so them
static.
Cleans up sparse warnings:
"symbol 'dwmac4_dma_init_rx_chan' was not declared. Should it be static?"
"symbol 'dwmac4_dma_init_tx_chan' was not declared. Should it be static?"
"symbol 'dwmac4_dma_init_channel' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoids reimplementation of DMI matching in stmmac_pci_find_phy_addr.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to carry this reference in stmmac_pci_info - the Quark-specific
setup handler knows that it needs to use the Quark-specific DMI table.
This also allows to drop the stmmac_pci_info reference from the setup
handler parameter list.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the special case for the early Galileo firmware into
quark_default_setup. This allows to use stmmac_pci_find_phy_addr for
non-quark cases.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make stmmac_default_data compatible with stmmac_pci_info.setup and use
an info structure for all devices. This allows to make the probing more
regular.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By removing the PCI device reference from the structure and passing it
as parameters to the interested functions, we can make quark_pci_info
const.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When having the skb pointer in the first descriptor, stmmac_tx_clean
can get called at a moment where the IP has only cleared the own bit
of the first descriptor, thus freeing the skb, even though there can
be several descriptors whose buffers point into the same skb.
By simply moving the skb pointer from the first descriptor to the last
descriptor, a skb will get freed only when the IP has cleared the
own bit of all the descriptors that are using that skb.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing in the IP that prevents us from enabling TSO for IPv6.
Before patch:
ftp fe80::2aa:bbff:fecc:1336%eth0
ftp> get /dev/zero
882512708 bytes received in 00:14 (56.11 MiB/s)
After patch:
ftp fe80::2aa:bbff:fecc:1336%eth0
ftp> get /dev/zero
1203326784 bytes received in 00:12 (94.52 MiB/s)
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allwinner V3s SoC has an Ethernet MAC and an internal PHY like the ones
in H3 SoC, however the MAC has no external *MII interfaces available at
GPIOs, thus only MII connection to internal PHY is supported.
Add this variant of EMAC to dwmac-sun8i driver.
The default value of the syscon EMAC-related register seems to have
changed from H3, but it seems to be a harmless change.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EPHY control part of the EMAC syscon register has a bit called
CLK_SEL. On the datasheet it says that if it's 0 the EPHY clock is 25MHz
and if it's 1 the clock is 24MHz.
However, according to the datasheets, no Allwinner SoC with EPHY has any
extra xtal input pins for the EPHY, and the system xtal is 24MHz.
That means the EPHY is not possible to get a 25MHz xtal input, and thus
the frequency can only be 24MHz.
It doesn't matter on H3 as the default value of H3 is 24MHz, however on
V3s the default value is wrongly set to 25MHz, which prevented the EPHY
from working properly.
Force the EPHY clock frequency to 24MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1.) Bugfix of function stmmac_get_tx_hwtstamp.
Corrected the tx timestamp available check (same as 4.8 and older)
Change printout from info syslevel to debug.
2.) Bugfix of function stmmac_get_rx_hwtstamp.
Corrected the rx timestamp available check (same as 4.8 and older)
Change printout from info syslevel to debug.
Fixes: ba1ffd74df ("stmmac: fix PTP support for GMAC4")
Signed-off-by: Mario Molitor <mario_molitor@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
According the CYCLON V documention only the bit 16 of snaptypesel should
set.
(more information see Table 17-20 (cv_5v4.pdf) :
Timestamp Snapshot Dependency on Register Bits)
Fixes: d2042052a0 ("stmmac: update the PTP header file")
Signed-off-by: Mario Molitor <mario_molitor@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check that queue is less or equal to zero is always true
because queue is a u32; queue is decremented and will wrap around
and never go -ve. Fix this by making queue an int.
Detected by CoverityScan, CID#1428988 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_tso_allocator can fail to set the Last Descriptor bit
on a descriptor that actually was the last descriptor.
This happens when the buffer of the last descriptor ends
up having a size of exactly TSO_MAX_BUFF_SIZE.
When the IP eventually reaches the next last descriptor,
which actually has the bit set, the DMA will hang.
When the DMA hangs, we get a tx timeout, however,
since stmmac does not do a complete reset of the IP
in stmmac_tx_timeout, we end up in a state with
completely hung TX.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current comparison of entry < 0 will never be true since entry is an
unsigned integer. Make entry an int to ensure -ve error return values
from the call to jumbo_frm are correctly being caught.
Detected by CoverityScan, CID#1238760 ("Macro compares unsigned to 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EPHY may be already enabled by bootloaders which have Ethernet
capability (e.g. current U-Boot). Thus it should be reseted properly
before doing the enabling sequence in the dwmac-sun8i driver, otherwise
the EMAC reset process may fail if no cable is plugged, and then fail
the dwmac-sun8i probing.
Tested on Orange Pi PC, One and Zero. All the boards fail to have
dwmac-sun8i probed with "EMAC reset timeout" without cable plugged
before, and with this fix they're now all able to successfully probe the
EMAC without cable plugged and then use the connection after a cable is
hot-plugged in.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: is not as formal as Signed-off-by:. It is a record that the acker
Reviewed-by: is similar.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NETDEV WATCHDOG timeout on startup by adding missing register
writes that properly setup SGMII.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-sun8i is a heavy hacked version of stmmac hardware by
allwinner.
In fact the only common part is the descriptor management and the first
register function.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of adding more ifthen logic for adding a new mac_device_info
setup function, it is easier to add a function pointer to the function
needed.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thoses symbol will be needed for the dwmac-sun8i ethernet driver.
For letting it to be build as module, they need to be exported.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current stmmac_adjust_link() part which handle speed have
some if (has_platform) code and my dwmac-sun8i will add more of them.
So we need to handle better speed selection.
Moreover the struct link member speed and port are hard to guess their
purpose. And their unique usage are to be combined for writing speed.
So this patch replace speed/port by simpler
speed10/speed100/speed1000/speed_mask variables.
In dwmac4_core_init and dwmac1000_core_init, port/speed value was used
directly without using the struct link. This patch convert also their
usage to speedxxx.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert old_link from int to bool since it store only 1 or 0
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert new_state from int to bool since it store only 1 or 0
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers were calling the skb_tx_timestamp() function only when
a hardware timestamp was not requested. Now that applications can use
the SOF_TIMESTAMPING_OPT_TX_SWHW option to request both software and
hardware timestamps, the drivers need to be modified to unconditionally
call skb_tx_timestamp().
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid
filter and update drivers which can timestamp all packets, or which
explicitly list unsupported filters instead of using a default case, to
handle the filter.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two pointers in sysfs_display_ring,
one that increments if using normal dma descriptors,
another if using extended dma descriptors.
When printing the normal dma descriptors, the wrong pointer is used,
thus the printed descriptor addresses are incorrect.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New helper is added in order to prevent misconfiguration happened
for one of the platforms when configuration data is expanded.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 26d6851fd2
("net: stmmac: set default number of rx and tx queues in stmmac_pci")
missed Intel Quark configuration. Append it here.
Fixes: 26d6851fd2 ("net: stmmac: set default number of rx and tx queues in stmmac_pci")
Cc: Joao Pinto <Joao.Pinto@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IOT2000 is industrial controller platform, derived from the Intel
Galileo Gen2 board. The variant IOT2020 comes with one LAN port, the
IOT2040 has two of them. They can be told apart based on the board asset
tag in the DMI table.
Based on patch by Sascha Weisenberger.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Field FL/TPL in register TDES3 is not correctly set on GMAC4.
TX appears to be functional on GMAC 4.10a even if this field is not set,
however, to avoid relying on undefined behavior, set the length in TDES3.
The field has a different meaning depending on if the TSE bit in TDES3
is set or not (TSO). However, regardless of the TSE bit, the field is
not optional. The field is already set correctly when the TSE bit is set.
Since there is no limit for the number of descriptors that can be
used for a single packet, the field should be set to the sum of
the buffers contained in:
[<desc with First Descriptor bit set> ... <desc n> ...
<desc with Last Descriptor bit set>], which should be equal to skb->len.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the submission of the lastest multiple buffer patch set, this fix was lost.
I am sending this patch to put it right again. The fix was originally proposed
by Arnd Bergmann.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the napi variable to the stmmac_rx_queue
structure and forces that operations like netif_queue_stopped,
netif_wake_queue, netif_stop_queue, netdev_reset_queue and
netdev_sent_queue be made by queue.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the structure stmmac_tx_queue which contains
tx queues specific data (previously in stmmac_priv).
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the structure stmmac_rx_queue which contains
rx queues specific data (previously in stmmac_priv).
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch breaks several functions into RX and TX scopes, which
will be useful when adding multiple buffers mechanism.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hardware configurations where multiple queues are active,
the rx queue needs to be mapped into a dma channel, even if
a single rx queue is used.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending again, because forgot to include net-dev.
The QoS IP does not accept AVB capabilities to default/queue 0, this way we
guarantee 75% bandwidth for AVB. This patch assures that only queues >= 1
gets CBS confgured. Additional info was also added to stmmac.txt.
Reported-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATM dwmac-rk will always set and enable it's internal delay lines.
Using PHY internal delays in combination with the phy-mode
rgmii-id/rxid/txid was not possible. Only rgmii was supported.
Now we can disable rockchip's gmac delay lines and also use
rgmii-id/rxid/txid.
Tested only with a RK3288 based board.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit aff3d9eff8 ("net: stmmac: enable multiple buffers") breaks
numerous boards. while some patch exists for fixing some of it,
dwmac-sunxi is still broken with it.
Since this patch is very huge, it will be better to split it in smaller
part.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver must not access the two fields directly but should instead use
the helper functions to set the values and keep a consistent internal
state:
ethernet/stmicro/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
ethernet/stmicro/stmmac/stmmac_main.c:4083:8: error: 'struct net_device' has no member named 'real_num_rx_queues'; did you mean 'real_num_tx_queues'?
Fixes: a8f5102af2 ("net: stmmac: TX and RX queue priority configuration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two different set_mac functions exists but stmmac_dwmac4_set_mac() is
only used for enabling and never for disabling.
So on dwmac4, the MAC RX/TX is never disabled.
This patch add a generic function pointer set_mac() to stmmac_ops and
replace all call to stmmac_set_mac/stmmac_dwmac4_set_mac by a call to
this pointer.
Since dwmac4_ops is const, set_mac cannot be modified after, and so dwmac4_ops
is duplioacted like dwmac4_dma_ops.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma operation mode configuration routine was wrongly moved to a
function (stmmac_mtl_configuration) that is only executed if the
core version is >= 4.00.
Fixes: 6deee2221e ("net: stmmac: prepare dma op mode config for multiple queues")
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to support multiple queues in the device tree bindings
resulted in the number of RX and TX queues to be initialized to zero for
device trees not adhering to the new bindings.
Restore backwards-compatibility with those device trees by falling back
to a single RX and TX queues each.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC RX queues always need to be enabled in order to receive network
packets. Remove the condition that this only needs to be done for multi-
queue configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of RX queues' routing.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of RX and TX queues' priority.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates 2 new structures (stmmac_tx_queue and stmmac_rx_queue)
in include/linux/stmmac.h, enabling that each RX and TX queue has its
own buffers and data.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the main ISR for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures TSO for all available tx queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the DMA initialization process for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares RX and TX set tail functions for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares tx and rx ring length configuration for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rx watchdog configuration for all queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares DMA interrupts treatment for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares stmmac_err for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the RX/TX DMA stop/start process for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the DMA IRQ enable/disable process for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares DMA Operation Mode configuration for multiple queues.
The work consisted on breaking the DMA operation Mode configuration function
into RX and TX scope and adapting its mechanism in stmmac_main.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the rx queue default size when dma interrupts are treated,
since dma op mode can be also set there.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures default number of RX and TX queues when
using the pci glue driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of the AVB Credit-Based Shaper.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares mac debug dump for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares mac irq status treatment for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adapts flow_ctrl function to prepare it for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functionality of RX queue to dma channel mapping
based on configuration.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the enabling of RX queues as DCB or as AVB based
on configuration.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the RX and TX scheduling algorithms programming.
It introduces the multiple queues configuration function
(stmmac_mtl_configuration) in stmmac_main.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the multiple queues configuration in the Device Tree.
It was also created a set of structures to keep the RX and TX queues
configurations to be used in the driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NVIDIA Tegra186 SoC contains an instance of the Synopsys DWC
ethernet QOS IP core. The binding that it uses is slightly different
from existing ones because of the integration (clocks, resets, ...).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the binding specific parts of ->probe() and ->remove() to
enable the driver to support variants of the binding. This is useful in
order to keep backwards-compatibility while making it easy for a sub-
driver to deal only with the updated bindings rather than having to add
compatibility quirks all over the place.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Program the receive queue size based on the RX FIFO size and enable
hardware flow control for large FIFOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New version of this core encode the FIFO sizes in one of the feature
registers. Use these sizes as default, but still allow device tree to
override them for backwards compatibility.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DMA mapping an SKB fragment, the mapping must be checked for
errors, otherwise the DMA debug code will complain upon unmap.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare_enable() and clk_disable_unprepare() for this clock aren't
properly balanced, which can trigger a WARN_ON() in the common clock
framework.
Reviewed-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs while opening the device, make sure to disable the
PTP reference clock.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs while opening the device, make sure that both the TX
timer and the PHY are properly cleaned up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There aren't currently any users of the "clk_ptp_ref", but there are
other references to "ptp_ref", so I'm leaning towards considering that a
typo. Fix it.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The axi variable was not being freed upon device removal.
With devm_kzalloc it ensures that it is properly freed.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver have two methods for registers dumps: via ethtool and
at init (if NETIF_MSG_HW is enabled).
It is better to keep only one method, ethtool, since the other was ugly.
This patch convert all dump_regs() function from "printing regs" to
"fill the reg_space used by ethtool".
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on rk3328 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: david.wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is easier to follow the logic by removing the not operator
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Joe Perches, replacing the "if phydev" logic permit to
reduce indentation in the for loop.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 10/100 case have too many ifcase.
This patch split it for removing an if.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch mutualise a bit by running stmmac_hw_fix_mac_speed() after
the switch in case of valid speed.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of invalid speed given, stmmac_adjust_link() still record it as
current speed.
This patch modify the default case to set speed as SPEED_UNKNOWN if not
10/100/1000.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is better to use DUPLEX_UNKNOWN instead of just "-1".
Using 0 for an invalid speed is bad since 0 is a valid value for speed.
So this patch replace 0 by SPEED_UNKNOWN.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_adjust_link() function is called too rarely for having
likely() macros being useful.
Just remove likely annotation in it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove some useless parenthesis.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch complains about two unsigned without type after.
Since the value return is u32, it is simpler to replace it by u32 instead
of "unsigned int"
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u64 x variable in sysfs_display_ring is unused.
This patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cf32deec16 ("stmmac: add tx_skbuff_dma to save descriptors used by PTP"),
the struct dma_desc *p in stmmac_tx_clean was not used at all.
This patch remove this dead code.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY is found, printing which one was found (and which type/model) is
a good information to know.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool stat counter rx_crc from stmmac is mis-named, the name
seems to speak about the number of RX CRC done, but in fact it is about
errors.
This patch rename it to rx_crc_errors, just like the same ifconfig
counter.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rewrite two test against NULL value with correct style.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message about invalid speed does not state 1000 as a valid speed.
It is much simpler to said that the speed is invalid.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said by checkpatch ENOSYS means 'invalid syscall nr' and nothing
else.
This patch replace ENOSYS by the more appropriate value EINVAL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac_dma_reset function use an open coded of readl_poll_timeout().
Replace the open coded handling with the proper function.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_mdio_busy_wait() function do the same job than
readl_poll_timeout().
So is is better to replace it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch complains about some code style problem on stmmac_mdio.c.
This patch fix them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the checkpatch warning about asm/io.h.
Sorting all includes in the process.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the checkpatch warning about free software address.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix some typos in comments.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bus_setup function pointer is not used at all, this patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the define MAC_RNABLE_RX have a typo, rename it to MAC_ENABLE_RX
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most likely a copy & paste error in referenced commit.
Restore the debug message to what it was before.
Fixes: f573c0b9c4 ("stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chips like Amlogic S905GXBB are supported by this driver but don't
have support for PTP. Add a separate warning for missing HW support
to differentiate it from other actual failures.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As documented in Documentation/devicetree/bindings/net/ethernet.txt,
in RGMII_ID and RGMII_TXID mode the MAC should not add a tx delay.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DW GMAC databook says the following about bits in "Register 15 (Interrupt
Mask Register)":
--------------------------->8-------------------------
When set, this bit __disables_the_assertion_of_the_interrupt_signal__
because of the setting of XXX bit in Register 14 (Interrupt
Status Register).
--------------------------->8-------------------------
In fact even if we mask one bit in the mask register it doesn't prevent
corresponding bit to appear in the status register, it only disables
interrupt generation for corresponding event.
But currently we expect a bit different behavior: status bits to be in
sync with their masks, i.e. if mask for bit A is set in the mask
register then bit A won't appear in the interrupt status register.
This was proven to be incorrect assumption, see discussion here [1].
That misunderstanding causes unexpected behaviour of the GMAC, for
example we were happy enough to just see bogus messages about link
state changes.
So from now on we'll be only checking bits that really may trigger an
interrupt.
[1] https://lkml.org/lkml/2016/11/3/413
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Phil Reid <preid@electromag.com.au>
Cc: David Miller <davem@davemloft.net>
Cc: Alexandre Torgue <alexandre.torgue@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch we were using a hardcoded RGMII TX clock delay of
2ns (= 1/4 cycle of the 125MHz RGMII TX clock). This value works for
many boards, but unfortunately not for all (due to the way the actual
circuit is designed, sometimes because the TX delay is enabled in the
PHY, etc.). Making the TX delay on the MAC side configurable allows us
to support all possible hardware combinations.
This allows fixing a compatibility issue on some boards, where the
RTL8211F PHY is configured to generate the TX delay. We can now turn
off the TX delay in the MAC, because otherwise we would be applying the
delay twice (which results in non-working TX traffic).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the LS mask when setting EEE timer.
LS field is 10 bits long and not 11 as currently.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reported-By: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds more info to stmicro' Kconfig files in order to be clearer
that the driver can be used by ethernet cards based on 10/100/1000/EQOS
Synopsys IP Cores.
EQOS was also added stmmac/Kconfig Kconfig, since dwmac4 is in fact EQoS,
one of Synopsys Ethernet IPs. More info at:
https://www.synopsys.com/dw/ipdir.php?ds=dwc_ether_qos
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function stmmac_dt_phy provides several possibilities for initializing
plat->mdio_node, all of which have the effect of increasing the reference
count of the assigned value. This field is not updated elsewhere, so the
value is live until the end of the lifetime of plat (devm_allocated), just
after the end of stmmac_remove_config_dt. Thus, add an of_node_put on
plat->mdio_node in stmmac_remove_config_dt. It is possible that the field
mdio_node is never initialized, but of_node_put is NULL-safe, so it is also
safe to call of_node_put in that case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use netdev_info and friends before the net_device is registered.
This avoids ugly messages like
"meson8b-dwmac c9410000.ethernet (unnamed net_device) (uninitialized):
Enable RX Mitigation via HW Watchdog Timer"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The break statement should be indented one more tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new glue driver called dwmac-dwc-qos-eth which
was based in the dwc_eth_qos as is. To assure retro-compatibility a slight
tweak was also added to stmmac_platform.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to the
plat_stmmacenet_data structure. It also moves these platform variables
initialization to stmmac_platform. This was done for two reasons:
a) If PCI is used, platform related code is being executed in stmmac_main
resulting in warnings that have no sense and conceptually was not right
b) stmmac as a synopsys reference ethernet driver stack will be hosting
more and more drivers to its structure like synopsys/dwc_eth_qos.c.
These drivers have their own DT bindings that are not compatible with
stmmac's. One of the most important are the clock names, and so they need
to be parsed in the glue logic and initialized there, and that is the main
reason why the clocks were passed to the platform structure.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new parameter to the stmmac DT: snps,en-tx-lpi-clockgating.
It was ported from synopsys/dwc_eth_qos.c and it is useful if lpi tx clock
gating is needed by stmmac users also.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no checking valid value of maxmtu when getting it from
device tree. This resolution added the checking condition to
ensure the assignment is made within a valid range.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have an exit callback in place, add init as well and get rid
of the custom PM callbacks in favour of the generic ones.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link phy registered during
probe on probe errors and on driver unbind by calling the new glue
helper function.
For driver unbind, use the generic stmmac-platform remove implementation
and add an exit callback to disable the clock.
Fixes: 5ed7414062 ("net: stmmac: Add OXNAS Glue Driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the syscon lookup-by-phandle helper so that the reference taken by
of_parse_phandle() is released when done with the node.
Fixes: 5ed7414062 ("net: stmmac: Add OXNAS Glue Driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For core revision 3.x Address-Aligned Beats is available in two registers.
The DT property snps,aal was created for AAL in the DMA bus register,
which is a read/write bit.
The DT property snps,axi_all was created for AXI_AAL in the AXI bus mode
register, which is a read only bit that reflects the value of AAL in the
DMA bus register.
Since the value of snps,axi_all is never used in the driver,
and since the property was created for a bit that is read only,
it should be safe to remove the property.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds Energy Efficiency Ethernet to GMAC4.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5701659004 ("net: stmmac: Fix race between stmmac_drv_probe and
stmmac_open") re-ordered how the MDIO bus registration and the network
device are registered, but missed to unwind the MDIO bus registration in
case we fail to register the network device.
Fixes: 5701659004 ("net: stmmac: Fix race between stmmac_drv_probe and stmmac_open")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the hardware is synthesized with multiple queues, all queues are
disabled for default. This patch adds the rx queues configuration.
This patch was successfully tested in a Synopsys QoS Reference design.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently a small window during which the network device registered by
stmmac can be made visible, yet all resources, including and clock and MDIO bus
have not had a chance to be set up, this can lead to the following error to
occur:
[ 473.919358] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
stmmac_dvr_probe: warning: cannot get CSR clock
[ 473.919382] stmmaceth 0000:01:00.0: no reset control found
[ 473.919412] stmmac - user ID: 0x10, Synopsys ID: 0x42
[ 473.919429] stmmaceth 0000:01:00.0: DMA HW capability register supported
[ 473.919436] stmmaceth 0000:01:00.0: RX Checksum Offload Engine supported
[ 473.919443] stmmaceth 0000:01:00.0: TX Checksum insertion supported
[ 473.919451] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
Enable RX Mitigation via HW Watchdog Timer
[ 473.921395] libphy: PHY stmmac-1:00 not found
[ 473.921417] stmmaceth 0000:01:00.0 eth0: Could not attach to PHY
[ 473.921427] stmmaceth 0000:01:00.0 eth0: stmmac_open: Cannot attach to
PHY (error: -19)
[ 473.959710] libphy: stmmac: probed
[ 473.959724] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 0 IRQ POLL
(stmmac-1:00) active
[ 473.959728] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 1 IRQ POLL
(stmmac-1:01)
[ 473.959731] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 2 IRQ POLL
(stmmac-1:02)
[ 473.959734] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 3 IRQ POLL
(stmmac-1:03)
Fix this by making sure that register_netdev() is the last thing being done,
which guarantees that the clock and the MDIO bus are available.
Fixes: 4bfcbd7abc ("stmmac: Move the mdio_register/_unregister in probe/remove")
Reported-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing stmmac with my QoS reference design I checked a problem in the
CSR clock configuration that was impossibilitating the phy discovery, since
every read operation returned 0x0000ffff. This patch fixes the issue.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the dwmac-rk tries to set up the GRF-specific speed and link
options before enabling clocks, phys etc and on previous socs this works
because the GRF is supplied on the whole by one clock.
On the rk3399 however the GRF (General Register Files) clock-supply
has been split into multiple clocks and while there is no specific
grf-gmac clock like for other sub-blocks, it seems the mac-specific
portions are actually supplied by the general mac clock.
This results in hangs on rk3399 boards if the driver is build as module.
When built in te problem of course doesn't surface, as the clocks
are of course still on at the stage before clock_disable_unused.
To solve this, simply move the clock enablement to the first position
in the powerup callback. This is also a good idea in general to
enable clocks before everything else.
Tested on rk3288, rk3368 and rk3399 the dwmac still works on all of them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up memory barriers in stmmac driver. They are meant to protect
against DMA engine, so smp_ variants are certainly wrong, and dma_
variants are preferable.
Signed-off-by: Pavel Machek <pavel@denx.de>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.
On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.
Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA_BUS_MODE_RPBL_MASK is really 6 bits,
just like DMA_BUS_MODE_PBL_MASK.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 64c3b252e9 ("net: stmmac: fixed the pbl setting with DT")
changed the parsing of the DT binding.
Before 64c3b252e9, snps,fixed-burst and snps,mixed-burst were parsed
regardless if the property snps,pbl existed or not.
After the commit, fixed burst and mixed burst are only parsed if
snps,pbl exists. Now when snps,aal has been added, it too is only
parsed if snps,pbl exists.
Since the DT binding does not specify that fixed burst, mixed burst
or aal depend on snps,pbl being specified, undo changes introduced
by 64c3b252e9.
The issue commit 64c3b252e9 ("net: stmmac: fixed the pbl setting with
DT") tries to address is solved in another way:
The databook specifies that all values other than
1, 2, 4, 8, 16, or 32 results in undefined behavior,
so snps,pbl = <0> is invalid.
If pbl is 0 after parsing, set pbl to DEFAULT_DMA_PBL.
This handles the case where the property is omitted, and also handles
the case where the property is specified without any data.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct stmmac_dma_cfg *dma_cfg as an argument rather
than using all the struct members as individual arguments.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers except pci glue layer calls stmmac_probe_config_dt.
stmmac_probe_config_dt does a kzalloc dma_cfg.
pci glue layer does kzalloc dma_cfg explicitly, so all current
drivers does a kzalloc dma_cfg.
Return an error if no DMA configuration is found, that way
we can assume that the DMA configuration always exists.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Previously, when specifying "snps,dwmac-4.10a", "snps,dwmac" as your
compatible string, plat_stmmacenet_data would have both has_gmac and
has_gmac4 set.
This would lead to stmmac_hw_init calling dwmac1000_setup rather than
dwmac4_setup, resulting in a non-functional driver.
This happened since the check for has_gmac is done before the check for
has_gmac4. However, the order should not matter, so it does not make sense
to have both set.
If something is valid for both, you should do as the stmmac_interrupt does:
if (priv->plat->has_gmac || priv->plat->has_gmac4) ...
The places where it was obvious that the author actually meant
if (has_gmac || has_gmac4) rather than if (has_gmac) has been updated.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Since dwmac-generic.c calls stmmac_probe_config_dt explicitly,
another alternative would have been to remove all compatible strings
other than "snps,dwmac" and "st,spear600-gmac" from dwmac-generic.c.
However, that would probably do more good than harm, since when trying
to figure out what hardware a certain driver supports, you usually look
at the compatible strings in the struct of_device_id, and not in some
function defined in a completely different file.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From what I can tell, spin_lock(&priv->lock) is not needed, since the
phy_ethtool_ksettings_set call is not given the priv struct.
phy_start_aneg takes the phydev->lock. Calls to phy_adjust_link
from phy_state_machine also takes the phydev->lock.
[ 13.718319] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97
[ 13.726717] in_atomic(): 1, irqs_disabled(): 0, pid: 1307, name: ethtool
[ 13.742115] Hardware name: Axis ARTPEC-6 Platform
[ 13.746829] [<80110568>] (unwind_backtrace) from [<8010c2bc>] (show_stack+0x18/0x1c)
[ 13.754575] [<8010c2bc>] (show_stack) from [<80433484>] (dump_stack+0x80/0xa0)
[ 13.761801] [<80433484>] (dump_stack) from [<80145428>] (___might_sleep+0x108/0x170)
[ 13.769554] [<80145428>] (___might_sleep) from [<806c9b50>] (mutex_lock+0x24/0x44)
[ 13.777128] [<806c9b50>] (mutex_lock) from [<8050cbc0>] (phy_start_aneg+0x1c/0x13c)
[ 13.784783] [<8050cbc0>] (phy_start_aneg) from [<8050d338>] (phy_ethtool_ksettings_set+0x98/0xd0)
[ 13.793656] [<8050d338>] (phy_ethtool_ksettings_set) from [<80517adc>] (stmmac_ethtool_set_link_ksettings+0xa0/0xb4)
[ 13.804184] [<80517adc>] (stmmac_ethtool_set_link_ksettings) from [<805c5138>] (ethtool_set_settings+0xd4/0x13c)
[ 13.814358] [<805c5138>] (ethtool_set_settings) from [<805c9718>] (dev_ethtool+0x13c4/0x211c)
[ 13.822882] [<805c9718>] (dev_ethtool) from [<805dc7c0>] (dev_ioctl+0x480/0x8e0)
[ 13.830291] [<805dc7c0>] (dev_ioctl) from [<80260e34>] (do_vfs_ioctl+0x94/0xa00)
[ 13.837699] [<80260e34>] (do_vfs_ioctl) from [<802617dc>] (SyS_ioctl+0x3c/0x60)
[ 13.845011] [<802617dc>] (SyS_ioctl) from [<801088bc>] (__sys_trace_return+0x0/0x10)
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WR_OSR_LMT and RD_OSR_LMT have a reset value of 1.
Since the reset value wasn't cleared before writing, the value in the
register would be incorrect if specifying an uneven value for
snps,wr_osr_lmt/snps,rd_osr_lmt.
Zero is a valid value for the properties, since the databook specifies:
maximum outstanding requests = WR_OSR_LMT + 1.
We do not want to change the behavior for existing users when the
property is missing. Therefore, default to 1 if the property is missing,
since that is the same as the reset value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_mdio_{read|write} and stmmac_mdio_{read|write}_gmac4 are not
enought different for being split.
The only differences between thoses two functions are shift/mask for
addr/reg/clk_csr.
This patch introduce a per platform set of variable for setting thoses
shift/mask and unify mdio read and write functions.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simply rename regValue to value, like it was named in other
mdio functions.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link phy registered during
probe on probe errors and on driver unbind by adding a new glue helper
function.
Drop the of-node reference taken in the same path also on late probe
errors (and not just on driver unbind) by moving the put from
stmmac_dvr_remove() to the new helper.
Fixes: 277323814e ("stmmac: add fixed-link device-tree support")
Fixes: 4613b279be ("ethernet: stmicro: stmmac: add missing of_node_put
after calling of_parse_phandle")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the OF-helper function header to reflect that the function no longer
has a platform-data parameter.
Fixes: b0003ead75 ("stmmac: make stmmac_probe_config_dt return the
platform data struct")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to disable clocks before returning on late probe errors.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic
Meson 8b / GXBB DWMAC")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to call any exit() callback to undo the effect of init()
before returning on late probe errors.
Fixes: cf3f047b9a ("stmmac: move hw init in the probe (v2)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to disable runtime PM, power down the PHY, and disable clocks
before returning on late probe errors.
Fixes: 27ffefd2d1 ("stmmac: dwmac-rk: create a new probe function")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to disable clocks before returning on late probe errors.
Fixes: 8387ee21f9 ("stmmac: dwmac-sti: turn setup callback into a
probe function")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to call stmmac_dvr_remove() before returning on late probe
errors so that memory is freed, clocks are disabled, and the netdev is
deregistered before its resources go away.
Fixes: 3c201b5a84 ("net: stmmac: socfpga: Remove re-registration of
reset controller")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix comments, add some new, and make debugfs output consistent.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac4 IP can synthesized with 1-8 number of tx queues.
On an IP synthesized with DWC_EQOS_NUM_TXQ > 1, all txqueues are disabled
by default. For these IPs, the bitfield TXQEN is R/W.
Always enable tx queue 0. The write will have no effect on IPs synthesized
with DWC_EQOS_NUM_TXQ == 1.
The driver does still not utilize more than one tx queue in the IP.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's not much point, except compile test, enabling the stmmac
platform drivers unless the STM32 SoC is enabled. It's not
useful without it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As sugested by Joe Perches, we could replace all
if (netif_msg_type(priv)) dev_xxx(priv->devices, ...)
by the simpler macro netif_xxx(priv, hw, priv->dev, ...)
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some printing have the function name hardcoded.
It is better to use __func__ instead.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver use lots of pr_xxx functions to print information.
This is bad since we cannot know which device logs the information.
(moreover if two stmmac device are present)
Furthermore, it seems that it assumes wrongly that all logs will always
be subsequent by using a dev_xxx then some indented pr_xxx like this:
kernel: sun7i-dwmac 1c50000.ethernet: no reset control found
kernel: Ring mode enabled
kernel: No HW DMA feature register supported
kernel: Normal descriptors
kernel: TX Checksum insertion supported
So this patch replace all pr_xxx by their netdev_xxx counterpart.
Excepts for some printing where netdev "cause" unpretty output like:
sun7i-dwmac 1c50000.ethernet (unnamed net_device) (uninitialized): no reset control found
In those case, I keep dev_xxx.
In the same time I remove some "stmmac:" print since
this will be a duplicate with that dev_xxx displays.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the generic phy_ethtool_nway_reset() helper function to
implement an autonegotiation restart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to break the hard dependency between the PTP clock subsystem and
ethernet drivers capable of being clock providers, this patch provides
simple PTP stub functions to allow linkage of those drivers into the
kernel even when the PTP subsystem is configured out. Drivers must be
ready to accept NULL from ptp_clock_register() in that case.
And to make it possible for PTP to be configured out, the select statement
in those driver's Kconfig menu entries is converted to the new "imply"
statement. This way the PTP subsystem may have Kconfig dependencies of
its own, such as POSIX_TIMERS, without having to make those ethernet
drivers unavailable if POSIX timers are cconfigured out. And when support
for POSIX timers is selected again then the default config option for PTP
clock support will automatically be adjusted accordingly.
The pch_gbe driver is a bit special as it relies on extra code in
drivers/ptp/ptp_pch.c. Therefore we let the make process descend into
drivers/ptp/ even if PTP_1588_CLOCK is unselected.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-kbuild@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Michal Marek <mmarek@suse.com>
Link: http://lkml.kernel.org/r/1478841010-28605-4-git-send-email-nicolas.pitre@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The stmmac driver does not take into account the processor may be big
endian when writing the DMA descriptors. This causes the ethernet
interface not to be initialised correctly when running a big-endian
kernel. Change the descriptors for DMA to use __le32 and ensure they are
suitably swapped before writing. Tested successfully on the
Cubieboard2.
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the ethtool stats for PTP frames; previous
version does not take care about some message types: i.e.
announce, management and signaling. It also provided a
broken statistic in case of "No PTP message received".
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to bad management of the descriptors, when use ptp4l,
kernel panics as shown below:
-----------------------------------------------------------
Unable to handle kernel NULL pointer dereference at virtual
address 000001ac
...
Internal error: Oops: 17 [#1] SMP ARM
...
Hardware name: STi SoC with Flattened Device Tree
task: c0c05e80 task.stack: c0c00000
PC is at dwmac4_wrback_get_tx_timestamp_status+0x0/0xc
LR is at stmmac_tx_clean+0x2f8/0x4d4
-----------------------------------------------------------
In case of GMAC4 the extended descriptor pointers were
used for getting the timestamp. These are NULL for this HW,
and the normal ones must be used.
The PTP also had problems on this chip due to the bad
register management and issues on the algo adopted to
setup the PTP and getting the timestamp values from the
descriptors.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to update this file by using BIT macros, removing
not used defines and fixes some typos.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSE PCS SGMII ethernet has an issue where switching speed doesn't work
caused by a faulty register macro offset. This fixes the issue.
Signed-off-by: Jia Jie Ho <ho.jia.jie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 52f95bbfcf ("stmmac: fix adjust link call in case of a switch
is attached") added some logic to avoid polling the fixed PHY and
therefore invoking the adjust_link callback more than once, since this
is a fixed PHY and link events won't be generated.
This works fine the first time, because we start with phydev->irq =
PHY_POLL, so we call adjust_link, then we set phydev->irq =
PHY_IGNORE_INTERRUPT and we stop polling the PHY.
Now, if we called ndo_close(), which calls both phy_stop() and does an
explicit netif_carrier_off(), we end up with a link down. Upon calling
ndo_open() again, despite starting the PHY state machine, we have
PHY_IGNORE_INTERRUPT set, and we generate no link event at all, so the
link is permanently down.
Fixes: 52f95bbfcf ("stmmac: fix adjust link call in case of a switch is attached")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of adding hooks inside stmmac_platform it is better to just use
the standard PM callbacks within the specific dwmac-driver. This only
used by the dwmac-rk driver.
This reverts commit cecbc5563a ("stmmac: allow to split suspend/resume
from init/exit callbacks").
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the rk_gmac_init() only calls another function move this
function call into probe so rk_gmac_init() can be removed.
Since commit cecbc5563a ("stmmac: allow to split suspend/resume
from init/exit callbacks") the init hook is no longer used in
dwmac-rk so this can be removed.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the exit hook into a standard driver remove function as
the hook doesn't really buy us anything extra.
Eventually the exit hook will be deprecated in favor of the driver
remove function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard PM resume/suspend callbacks instead of the hooks in
stmmac_platform. This gives the driver more control and flexibility
when implementing PM functionality. The hooks in stmmac_platform
also doesn't buy us anything extra.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev member of struct sti_dwmac is not used anywhere in the driver
so lets just remove it.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename sti_dwmac_init to sti_dwmac_set_mode which is a better
description for what it really does.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add clock error handling to probe and in the process move clock enabling
out of sti_dwmac_init() to make this easier.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sti_dwmac_init() function is called both from probe and resume.
Since DT properties doesn't change between suspend/resume cycles move
parsing of this parameter into sti_dwmac_parse_data() where it belongs.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thor Thayer