This patch does not change any functionality.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: extracted this patch from a larger patch ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CONFIG_SCSI_UFS_QCOM selects CONFIG_PHY_QCOM_UFS, assuming that this was
the only possible PHY driver Qualcomm's UFS controller would use. But in
SDM845, the UFS driver is bundled into phy-qcom-qmp, and phy-qcom-ufs is
unused.
Remove the select, since for SDM845 it adds useless drivers to the build.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The tmscsim.txt doc file was removed in c121107d0f.
Fixes: c121107d0f ("scsi: documentation: Obsolete documentation references")
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the SMP PHY control execution result is checked, however the
function result for the command is not.
As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.
In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SGE buffer containing DIF information crosses 4G boundary, it results
in DMA error. This patch fixes this issue by calculating SGE buffer size
and if it crosses 4G boundary, driver will split it into multiple SGE
buffers to avoid DMA error.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow user to selectively enable/disable DIF/DIX protection
capabilities mask.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in some cases, I replaced "FALLTHROUGH" with a "fall through"
annotation and then placed it at the bottom of the corresponding switch
case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 114961 ("Missing break in switch")
Addresses-Coverity-ID: 114962 ("Missing break in switch")
Addresses-Coverity-ID: 114963 ("Missing break in switch")
Addresses-Coverity-ID: 114964 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "!!! fall through !!!"
comment with "fall through" annotations, which is what GCC is expecting to
find.
Addresses-Coverity-ID: 146155 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that I replaced "!! fall through !!" and "!!! fall through !!!"
comments with "fall through" annotations, which is what GCC is expecting to
find.
Addresses-Coverity-ID: 744899 ("Missing break in switch")
Addresses-Coverity-ID: 744900 ("Missing break in switch")
Addresses-Coverity-ID: 744901 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "!!! fall through !!!"
with a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Bradley Grove <bgrove@atto.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 114994 ("Missing break in switch")
Addresses-Coverity-ID: 114995 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "allow fall-through" with
a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return statement is indented incorrectly, fix this by removing a single
tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the protection lookup tables in sd_prot_flag_mask() and
sd_prot_op() are declared as non-static. As such, they will be rebuilt for
each respective function call.
Optimise by making them static.
This saves ~100B object code for sd.c:
Before:
text data bss dec hex filename
25403 1024 16 26443 674b drivers/scsi/sd.o
After:
text data bss dec hex filename
25299 1024 16 26339 66e3 drivers/scsi/sd.o
In addition, since those same functions are declared in sd.h, but each are
only referenced in sd.c, relocate them to that same c file.
The inline specifier is dropped also, since gcc should be able to make the
decision to inline.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for IOST and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for DQ and add file operations
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for CQ and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for port register and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for global register and add file
operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch takes snapshot for global regs, port regs, CQ, DQ, IOST, ITCT.
Add code for snapshot trig and generate dump directory.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allocates snapshot memory for global reg, port regs, CQ, DQ,
IOST, ITCT.
When we fail to allocate memory for some registers, we free the memory
and set hisi_sas_debugfs_enable as 0 to stop loading debugfs from running.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch creates root directory at hisi_sas_init() and generates device
directory when we probe device driver.
And we remove the root directory at hisi_sas_exit(), but recursively
delete device directory when we remove device driver.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Update driver version to v1.40.00.10-20181217
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Fix suspend/resume of ACB_ADAPTER_TYPE_B
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Separate 'set dma mask' as a function
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Add an option of set dma_mask_64 for ACB_ADAPTER_TYPE_A
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_D for >4gb ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_C for >4GB ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_B for >4GB ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_A for >4GB ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Merge arcmsr_alloc_io_queue to arcmsr_alloc_ccb_pool
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Rename arcmsr_free_mu to arcmsr_free_io_queue
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Rename acb structure member roundup_ccbsize to ioqueue_size
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API. Also switch
to dma_map_single from pci_map_page in one case where this makes the code
simpler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code has been under a never defined ifdef since the beginning
of time (or at least history), and has just bitrotted. Nuke it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This can't ever be compiled into the kernel, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code can't be built into the kernel without editing the source
file and is not generally useful.
[mkp: typo]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code has been under the never defined GDTH_RTC ifdef forever,
nuke it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove never compile in support for sending debug traces straight to
the serial port using direct port access.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The non-PCI code has bitrotted for quite a while and will just oops
on load because it passes a NULL pointer to the PCI DMA routines.
Lets kill it for good - if someone really wants to use one of these
cards I'll help mentoring them to write a proper driver glue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Out of the three callers once insists on the scratch buffer, and the
others are fine with a new allocation. Switch those two to just use
pci_alloc_consistent directly, and open code the scratch buffer
allocation in the remaining one. This avoids a case where we might
be doing a memory allocation under a spinlock with irqs disabled.
[mkp: typo]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gdth_show_info currently allocs and frees a dma buffer four times which
isn't very efficient. Reuse a single allocation instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This function is a huge mess with duplicated error handling. Split out
a few useful helpers and use goto labels to untangle the error handling
and no-data ioctl handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
Bart Van Assche