06781a5026 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 06781a5026 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 06781a5026 ("mtd: rawnand: gpmi: Fix setting busy timeout setting")
Fixes: b120612206 ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
According to the Arasan NAND controller spec, the flash clock rate for SDR
must be <= 100 MHz, while for NV-DDR it must be the same as the rate of the
CLK line for the mode. The driver previously always set 100 MHz for NV-DDR,
which would result in incorrect behavior for NV-DDR modes 0-4.
The appropriate clock rate can be calculated from the NV-DDR timing
parameters as 1/tCK, or for rates measured in picoseconds,
10^12 / nand_nvddr_timings->tCK_min.
Fixes: 197b88fecc ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Olga Kitaina <okitain@gmail.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-3-amit.kumar-mahapatra@xilinx.com
In current implementation the Arasan NAND driver is updating the
system clock(i.e., anand->clk) in accordance to the timing modes
(i.e., SDR or NVDDR). But as per the Arasan NAND controller spec the
flash clock or the NAND bus clock(i.e., nfc->bus_clk), need to be
updated instead. This patch keeps the system clock unchanged and updates
the NAND bus clock as per the timing modes.
Fixes: 197b88fecc ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-2-amit.kumar-mahapatra@xilinx.com
We have many parser that register mtd partitions at runtime. One example
is the cmdlinepart or the smem-part parser where the compatible is defined
in the dts and the partitions gets detected and registered by the
parser. This is problematic for the NVMEM subsystem that requires an OF
node to detect NVMEM cells.
To fix this problem, introduce an additional logic that will try to
assign an OF node to the MTD if declared.
On MTD addition, it will be checked if the MTD has an OF node and if
not declared will check if a partition with the same label / node name is
declared in DTS. If an exact match is found, the partition dynamically
allocated by the parser will have a connected OF node.
The NVMEM subsystem will detect the OF node and register any NVMEM cells
declared statically in the DTS.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220622010628.30414-4-ansuelsmth@gmail.com
blk_cleanup_disk is nothing but a trivial wrapper for put_disk now,
so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20220619060552.1850436-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The SECT_4K_PMC flag will set a device specific opcode for the 4k sector
erase. Instead of handling it in the core, we can move it to a
late_init(). In that late init, loop over all erase types, look for the
4k size and replace the opcode.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220418112650.2791459-1-michael@walle.cc
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220620152313.708768-1-broonie@kernel.org
there is an unexpected word 'is' in the comments that need to be dropped
file: drivers/mtd/nand/raw/sm_common.c
line: 55
/* NOTE: This layout is is not compatabable with SmartMedia, */
changed to:
/* NOTE: This layout is not compatabable with SmartMedia, */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220622160511.11679-1-jiangjian@cdjrlc.com
IPQ8064 nand have special pages where a different layout scheme is used.
These special page are used by boot partition and on reading them
lots of warning are reported about wrong ECC data and if written to
results in broken data and not bootable device.
The layout scheme used by these special page consist in using 512 bytes
as the codeword size (even for the last codeword) while writing to CFG0
register. This forces the NAND controller to unprotect the 4 bytes of
spare data.
Since the kernel is unaware of this different layout for these special
page, it does try to protect the spare data too during read/write and
warn about CRC errors.
Add support for this by permitting the user to declare these special
pages in dts by declaring offset and size of the partition. The driver
internally will convert these value to nand pages.
On user read/write the page is checked and if it's a boot page the
correct layout is used.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220616001835.24393-3-ansuelsmth@gmail.com
of_get_child_by_name() will increase the refcount of 'ofpart_node',
so add of_node_put() after using it to avoid refcount leak.
Fixes: 9b78ef0c79 ("mtd: parsers: add support for Sercomm partitions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220617014008.851583-1-yangyingliang@huawei.com
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY
| mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to
divide it by that value. Use DIV_ROUND_UP to make sure we are on the
safe side, especially when the calculated value in cycles is smaller
than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will
do. In my case the busy timeout in cycles was originally calculated as
2408, which multiplied with 4096 is 0x968000. The lower 16 bits were
taken for the 16 bit wide register field, so the register value was
0x8000. With 2970bf5a32 ("mtd: rawnand: gpmi: fix controller timings
setting") however the value in cycles became 2384, which multiplied
with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an
intermediate timeout when reading from NAND.
Fixes: b120612206 ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
This reverts commit 3380557fc7.
It turned out this "4-byte" ID might have been an honest mistake.
Regrettably, the chip Andreas has might be a counterfeit or is
damaged in some other way and shouldn't have ended up in a router.
Andreas reported his chip is returning just four bytes:
"98 f1 80 15 00 00 00 00".
However, according to Kioxia/Toshiba's datasheet, there should
have been at least another byte that would have contained the
correct OOB size that Andreas needed.
Miquel and Andreas are both favoring reverting the patch over
further, possibly hacky modifications:
"[Reverting] is the safest option here. Apart from this device, we
do not know how many devices have these damaged/counterfeit chips.
If it is just a couple and only on Fritzboxes, as suggested in the
Github issue the patch could be carried through OpenWrt[...]"
Thanks to several users on the openwrt forum and github issue,
who stayed along for the ride:
- Peter-vdL for reporting the issue and testing patches.
- neg2led and Hannu Nyman who did all the
datasheet digging and debugging.
Cc: Andreas Boehler <dev@aboehler.at>
Suggested-by: Andreas Boehler <dev@aboehler.at>
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://github.com/openwrt/openwrt/issues/9962
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607185918.1048204-1-chunkeey@gmail.com
Until mtd_device_unregister() returns the device is expected to be
operational. So only disable the clock after the mtd is unregistered.
Fixes: 1fefc8ecb8 ("mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607152458.232847-4-u.kleine-koenig@pengutronix.de
mtd_device_unregister() shouldn't fail. Wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
By returning 0 in the platform remove callback a generic error message
by the device core is suppressed, nothing else changes.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607152458.232847-3-u.kleine-koenig@pengutronix.de
For all but one error path clk_disable_unprepare() is already there. Add
it to the one location where it's missing.
Fixes: 481815a619 ("mtd: st_spi_fsm: Handle clk_prepare_enable/clk_disable_unprepare.")
Fixes: 69d5af8d01 ("mtd: st_spi_fsm: Obtain and use EMI clock")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607152458.232847-2-u.kleine-koenig@pengutronix.de
The Linux device core doesn't intend remove callbacks to fail. If an
error code is returned the device is removed anyhow. So wail loudly if
the atmel specific remove callback fails and return 0 anyhow to suppress
the generic (and little helpful) error message by the device core.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607062503.211345-1-u.kleine-koenig@pengutronix.de
The remove callback is only called after probe completed successfully.
In this case platform_set_drvdata() was called with a non-NULL argument
and so info is never NULL.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-15-u.kleine-koenig@pengutronix.de
If mtd_device_unregister() fails (which it doesn't when used correctly),
the resources bound by the nand chip should be freed anyhow as returning
an error value doesn't prevent the device getting unbound.
Instead use WARN_ON on the return value similar to how other drivers do
it.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-14-u.kleine-koenig@pengutronix.de
If mtd_device_unregister() fails (which it doesn't when used correctly),
the resources bound by the nand chip should be freed anyhow as returning
an error value doesn't prevent the device getting unbound.
Instead use WARN_ON on the return value similar to how other drivers do
it. Then meson_nfc_nand_chip_cleanup() returns 0 unconditionally and can
be changed to return void which allows further simplification in the
remove callback.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-12-u.kleine-koenig@pengutronix.de
If mtd_device_unregister() fails (which it doesn't when used correctly),
the resources bound by the nand chip should be freed anyhow as returning
an error value doesn't prevent the device getting unbound.
Instead use WARN_ON on the return value similar to how other drivers do
it.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-11-u.kleine-koenig@pengutronix.de
Returning an error value in a platform remove callback results in an error
message being emitted by the platform core, but otherwise it doesn't make
a difference. After the WARN splat this generic error message doesn't add
any value, so return 0 unconditionally
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-10-u.kleine-koenig@pengutronix.de
The remove callback is only called after probe completed successfully.
In this case platform_set_drvdata() was called with a non-NULL argument
and so dev is never NULL.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-8-u.kleine-koenig@pengutronix.de
If mtd_device_unregister() fails (which it doesn't when used correctly),
the resources bound by the nand chip should be freed anyhow as returning
an error value doesn't prevent the device getting unbound.
Instead use WARN_ON on the return value similar to how other drivers do
it.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-7-u.kleine-koenig@pengutronix.de
mtd_device_unregister() shouldn't fail. Wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
By returning 0 in the platform remove callback a generic error message
by the device core is suppressed, nothing else changes.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-6-u.kleine-koenig@pengutronix.de
mtd_device_unregister() shouldn't fail. Wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
By returning 0 in the platform remove callback a generic error message
by the device core is suppressed, nothing else changes.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-4-u.kleine-koenig@pengutronix.de
The only thing that could theoretically fail in that function is
mtd_device_unregister(). However it's not supposed to fail and when
used correctly it doesn't. So wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-2-u.kleine-koenig@pengutronix.de
mtdchar_write_ioctl() calls kmalloc() with the 'size' argument set to
the smaller of two values: the write request's data/OOB length provided
by user space and the erase block size of the MTD device. If the latter
is large, kmalloc() may not be able to serve such allocation requests.
Use kvmalloc() instead. Correspondingly, replace kfree() calls with
kvfree() calls.
Suggested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220516070601.11428-3-kernel@kempniu.pl
Commit 6420ac0af9 ("mtdchar: prevent unbounded allocation in MEMWRITE
ioctl") added a safety check to mtdchar_write_ioctl() which attempts to
ensure that the write request sent by user space does not extend beyond
the MTD device's size. However, that check contains an addition of two
struct mtd_write_req fields, 'start' and 'len', both of which are u64
variables. The result of that addition can overflow, allowing the
safety check to be bypassed.
The arguably simplest fix - changing the data types of the relevant
struct mtd_write_req fields - is not feasible as it would break user
space.
Fix by making mtdchar_write_ioctl() truncate the value provided by user
space in the 'len' field of struct mtd_write_req, so that only the lower
32 bits of that field are used, preventing the overflow.
While the 'ooblen' field of struct mtd_write_req is not currently used
in any similarly flawed safety check, also truncate it to 32 bits, for
consistency with the 'len' field and with other MTD routines handling
OOB data.
Update include/uapi/mtd/mtd-abi.h accordingly.
Suggested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220516070601.11428-2-kernel@kempniu.pl
of_find_node_by_path() returns a node pointer with refcount incremented,
we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: bb17230c61 ("mtd: parsers: ofpart: support BCM4908 fixed partitions")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220605070726.5979-1-linmq006@gmail.com
This adds an MTD partition parser for the Sercomm partition table that
is used in some Beeline, Netgear and Sercomm routers.
The Sercomm partition map table contains real partition offsets, which
may differ from device to device depending on the number and location of
bad blocks on NAND.
Original patch (proposed by NOGUCHI Hiroshi):
Link: https://github.com/openwrt/openwrt/pull/1318#issuecomment-420607394
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220529110714.189732-1-csharper2005@gmail.com
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 2379608809 ("mtd: partitions: redboot: seek fis-index-block in the right node")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220526110652.64849-1-linmq006@gmail.com
There is a deadlock between sm_release and sm_cache_flush_work
which is a work item. The cancel_work_sync in sm_release will
not return until sm_cache_flush_work is finished. If we hold
mutex_lock and use cancel_work_sync to wait the work item to
finish, the work item also requires mutex_lock. As a result,
the sm_release will be blocked forever. The race condition is
shown below:
(Thread 1) | (Thread 2)
sm_release |
mutex_lock(&ftl->mutex) | sm_cache_flush_work
| mutex_lock(&ftl->mutex)
cancel_work_sync | ...
This patch moves del_timer_sync and cancel_work_sync out of
mutex_lock in order to mitigate deadlock.
Fixes: 7d17c02a01 ("mtd: Add new SmartMedia/xD FTL")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220524044841.10517-1-duoming@zju.edu.cn
When meson_nfc_nand_chip_cleanup() is called, it will call:
meson_nfc_free_buffer(&meson_chip->nand);
nand_cleanup(&meson_chip->nand);
nand_cleanup() in turn will call nand_detach() which calls the
.detach_chip() which is here meson_nand_detach_chip().
meson_nand_detach_chip() already calls meson_nfc_free_buffer(), so we
could double free some memory.
Fix it by removing the unneeded explicit call to meson_nfc_free_buffer().
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/ec15c358b8063f7c50ff4cd628cf0d2e14e43f49.1653064877.git.christophe.jaillet@wanadoo.fr
Driver should call pci_disable_device() if it returns from
cafe_nand_probe() with error.
Meanwhile, the driver calls pci_enable_device() in
cafe_nand_probe(), but never calls pci_disable_device()
during removal.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220520084425.116686-1-wupeng58@huawei.com
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b0afd44bc1 ("mtd: physmap_of: add a hook for Versatile write protection")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220523143255.4376-1-linmq006@gmail.com
of_find_matching_node_and_match() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b0afd44bc1 ("mtd: physmap_of: add a hook for Versatile write protection")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220523140205.48625-1-linmq006@gmail.com
JFFS2:
- Fixes for a memory leak
UBI:
- Fixes for fastmap (UAF, high CPU usage)
UBIFS:
- Minor cleanups
-----BEGIN PGP SIGNATURE-----
iQJKBAABCAA0FiEEdgfidid8lnn52cLTZvlZhesYu8EFAmKZ0F0WHHJpY2hhcmRA
c2lnbWEtc3Rhci5hdAAKCRBm+VmF6xi7wVOsD/wMI9/RR3NQukIdj1besXnYWCGr
44PLTZsX+fwn/ndj/IDqtyZiStILQOX3gNK9bZ540bVQGkMxgYerQUjZH2A1CaBd
BwisUhU9duv6t6ObB8IudnqYB3nYTM7mRGQQOnkw0ddGdCoN7S8WB7ed7ce6bLF2
X4cbzpIfBhuXghKzZ0d9k/uNEj4ZcTsTov+yiX2F9M0xBgfFIoIrP51mk+5l7PAj
BmEqDFRfuTPm5u1WMUpThPX/RhSEu5PkZDLztSmD8WfiaF20KPFrWIMtKQmn/3vT
IkRzJoHZSX8KmjoD1eBHssblJwcF6l5OGZNrS2NGqJMpVtRJ2uFWq3lx/WjgN88W
/eqIoryYod8NTogTzl//y/mtDhSkaGK6LdDKjk5Z1gP1ferJNBw8k1+icR/YP4sj
/dBXJTI7nIrb79EegQHIGNVAfE+Oi+rjEB/r8cqG9z5sJQvCK9p30+cVJSuK0/Na
N6wX107HtgDh5kLaUKwTQjZBi/1TpV0dQCdAOkqgyn5YlzxXKFKISBrRIPuFtGXM
a6fBwd+RSd9ccWGPE4R+6JQELFOYDpOj6cunwheb0B1YLaDGoV+mjAcO6uGdExXy
+iErtxV1v+lXqslQKR09uO+N2gApQYF7B01TjDjyxWsKWABe55Tl3z8lGpPxGIcb
FvkFMzuuIE4FlyUY6g==
=QSbc
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Fixes for a memory leak
UBI:
- Fixes for fastmap (UAF, high CPU usage)
UBIFS:
- Minor cleanups"
* tag 'for-linus-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: ubi_create_volume: Fix use-after-free when volume creation failed
ubi: fastmap: Check wl_pool for free peb before wear leveling
ubi: fastmap: Fix high cpu usage of ubi_bgt by making sure wl_pool not empty
ubifs: Use NULL instead of using plain integer as pointer
ubifs: Simplify the return expression of run_gc()
jffs2: fix memory leak in jffs2_do_fill_super
jffs2: Use kzalloc instead of kmalloc/memset
The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went through
several rebases before the merge window as bugs were found, so they
remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files.
-----BEGIN PGP SIGNATURE-----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=cnSb
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
There is an use-after-free problem for 'eba_tbl' in ubi_create_volume()'s
error handling path:
ubi_eba_replace_table(vol, eba_tbl)
vol->eba_tbl = tbl
out_mapping:
ubi_eba_destroy_table(eba_tbl) // Free 'eba_tbl'
out_unlock:
put_device(&vol->dev)
vol_release
kfree(tbl->entries) // UAF
Fix it by removing redundant 'eba_tbl' releasing.
Fetch a reproducer in [Link].
Fixes: 493cfaeaa0 ("mtd: utilize new cdev_device_add helper function")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215965
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
UBI fetches free peb from wl_pool during wear leveling, so UBI should
check wl_pool's empty status before wear leveling. Otherwise, UBI will
miss wear leveling chances when free pebs are run out.
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
There at least 6 PEBs reserved on UBI device:
1. EBA_RESERVED_PEBS[1]
2. WL_RESERVED_PEBS[1]
3. UBI_LAYOUT_VOLUME_EBS[2]
4. MIN_FASTMAP_RESERVED_PEBS[2]
When all ubi volumes take all their PEBs, there are 3 (EBA_RESERVED_PEBS +
WL_RESERVED_PEBS + MIN_FASTMAP_RESERVED_PEBS - MIN_FASTMAP_TAKEN_PEBS[1])
free PEBs. Since commit f9c34bb529 ("ubi: Fix producing anchor PEBs")
and commit 4b68bf9a69 ("ubi: Select fastmap anchor PEBs considering
wear level rules") applied, there is only 1 (3 - FASTMAP_ANCHOR_PEBS[1] -
FASTMAP_NEXT_ANCHOR_PEBS[1]) free PEB to fill pool and wl_pool, after
filling pool, wl_pool is always empty. So, UBI could be stuck in an
infinite loop:
ubi_thread system_wq
wear_leveling_worker <--------------------------------------------------
get_peb_for_wl |
// fm_wl_pool, used = size = 0 |
schedule_work(&ubi->fm_work) |
|
update_fastmap_work_fn |
ubi_update_fastmap |
ubi_refill_pools |
// ubi->free_count - ubi->beb_rsvd_pebs < 5 |
// wl_pool is not filled with any PEBs |
schedule_erase(old_fm_anchor) |
ubi_ensure_anchor_pebs |
__schedule_ubi_work(wear_leveling_worker) |
|
__erase_worker |
ensure_wear_leveling |
__schedule_ubi_work(wear_leveling_worker) --------------------------
, which cause high cpu usage of ubi_bgt:
top - 12:10:42 up 5 min, 2 users, load average: 1.76, 0.68, 0.27
Tasks: 123 total, 3 running, 54 sleeping, 0 stopped, 0 zombie
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
1589 root 20 0 0 0 0 R 45.0 0.0 0:38.86 ubi_bgt0d
319 root 20 0 0 0 0 I 15.2 0.0 0:15.29 kworker/0:3-eve
371 root 20 0 0 0 0 I 14.9 0.0 0:12.85 kworker/3:3-eve
20 root 20 0 0 0 0 I 11.3 0.0 0:05.33 kworker/1:0-eve
202 root 20 0 0 0 0 I 11.3 0.0 0:04.93 kworker/2:3-eve
In commit 4b68bf9a69 ("ubi: Select fastmap anchor PEBs considering
wear level rules"), there are three key changes:
1) Choose the fastmap anchor when the most free PEBs are available.
2) Enable anchor move within the anchor area again as it is useful
for distributing wear.
3) Import a candidate fm anchor and check this PEB's erase count during
wear leveling. If the wear leveling limit is exceeded, use the used
anchor area PEB with the lowest erase count to replace it.
The anchor candidate can be removed, we can check fm_anchor PEB's erase
count during wear leveling. Fix it by:
1) Removing 'fm_next_anchor' and check 'fm_anchor' during wear leveling.
2) Preferentially filling one free peb into fm_wl_pool in condition of
ubi->free_count > ubi->beb_rsvd_pebs, then try to reserve enough
free count for fastmap non anchor pebs after the above prerequisites
are met.
Then, there are at least 1 PEB in pool and 1 PEB in wl_pool after calling
ubi_refill_pools() with all erase works done.
Fetch a reproducer in [Link].
Fixes: 4b68bf9a69 ("ubi: Select fastmap anchor PEBs ... rules")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215407
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This is quite a quiet release but some new drivers mean that the
diffstat is fairly large, the new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKLh9wACgkQJNaLcl1U
h9ApgAf/SvcHRyM06hw+00D2PAco7mxSiAs7rebxj4f0zPRNvUrYbUDWjakeKjoB
ocmpY6AW/vRBUM9xZsiQiLp/9NPltnVghZIBgp5gcS8zaXdxiZjZ68Z+uYp9SP9v
zj8F6bBQzk3lvuY+Cr1f68iXICA62Aa1yX28UFVLZkV0d+0AazpECZkb3hjOiL6P
0qSV6IfoFlJXYsyvAS4/MqYrHklSCD/0Ek09V9jPpZJPHn1ldbFs5zkstfs0PMc/
YeDlpStkjJE4OQ6+z6Ou/wGbcw11nWvKCSqF4bGRXLrgR/uIjOKomwOzaBUf/A6Q
AxQcKMtsBTx0VzYmwJwopj0qDvOq/A==
=6yj3
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This is quite a quiet release but some new drivers mean that the
diffstat is fairly large. The new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI"
* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
spi: spi-au1550: replace ternary operator with min()
mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
spi: aspeed: Calibrate read timings
spi: aspeed: Add support for the AST2400 SPI controller
spi: aspeed: Workaround AST2500 limitations
spi: aspeed: Adjust direct mapping to device size
spi: aspeed: Add support for direct mapping
spi: spi-mem: Convert Aspeed SMC driver to spi-mem
spi: Convert the Aspeed SMC controllers device tree binding
spi: spi-cadence: Update ISR status variable type to irqreturn_t
spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
spi: cadence-quadspi: Handle spi_unregister_master() in remove()
spi: stm32-qspi: Remove SR_BUSY bit check before sending command
spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
spi: stm32-qspi: Fix wait_cmd timeout in APM mode
spi: cadence-quadspi: remove unnecessary (void *) casts
spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
spi: spi-imx: add PIO polling support
spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
...
* Call of_platform_populate() for MTD partitions
* Check devicetree alias for index
* mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
* mtdblock: Warn if opened on NAND
* Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
* st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
* phram:
- Allow cached mappings
- Allow probing via reserved-memory
* maps: ixp4xx: Drop driver
* bcm47xxpart: Print correct offset on read error
CFI driver changes:
* Rename chip_ready variables
* Add S29GL064N ID definition
* Use chip_ready() for write on S29GL064N
* Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
SPI NOR core changes:
* Read back written SR value to make sure the write was done correctly.
* Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
* Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
* Clarify rdsr dummy cycles documentation.
* Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
* Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
* Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
* Rework Micron and Cypress Octal DTR enable methods to improve
readability.
* Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
* Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmKHhXEACgkQJWrqGEe9
VoQ4FQgAwTWnv7Eps8ngxlOE1WW1Kx+XUFCYN7mUKmDycgRKWWqF0OUu3pU6T3Si
XoOixajzsPC7AJtXbbGKUkH3UtqapCZ/OVxMJzY1S1zKVgS72ChvPth+rNOA5H6f
wkwCRYBCm51hYAlOQeRoFtwLEpOP17KTZw9Jn/u5RVwbQedQnzPj5sb6PddejjF4
9nlk2auJHzENBEEBG3WLRNgvGep8mNNFarzWB4iWrMcG0w1EgBksbIdshoBmu7vj
nKcDJbyA81DqX+8d56BfAFih8H2yCXZmhUzMK+zqnNkd1NuPnDDnrQYFKmKm2hAg
3bIMIzi+8dl/m0TY6BHPHj8oIYpjYA==
=P95J
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Call of_platform_populate() for MTD partitions
- Check devicetree alias for index
- mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
- mtdblock: Warn if opened on NAND
- Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
- st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
- phram:
- Allow cached mappings
- Allow probing via reserved-memory
- maps: ixp4xx: Drop driver
- bcm47xxpart: Print correct offset on read error
CFI driver changes:
- Rename chip_ready variables
- Add S29GL064N ID definition
- Use chip_ready() for write on S29GL064N
- Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
- Print offset instead of page number for bad blocks
Raw NAND controller drivers:
- Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
- CS553X: simplify the return expression of cs553x_write_ctrl_byte()
- Davinci: Remove redundant unsigned comparison to zero
- Denali: Use managed device resources
- GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
- Intel: Fix possible null-ptr-deref in ebu_nand_probe()
- MPC5121: Check before clk_disable_unprepare() not needed
- Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
- OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
- Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
- Rockchip: Check before clk_disable_unprepare() not needed
- TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
- Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
- Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
- XTX: Add support for XT26G0xA
SPI NOR core changes:
- Read back written SR value to make sure the write was done
correctly.
- Introduce a common function for Read ID that manufacturer drivers
can use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond
flashes use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode
for Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and
Cypress flashes since the operation is instant"
* tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits)
mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
dt-bindings: mtd: partitions: Extend fixed-partitions binding
dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix
mtd: phram: Allow cached mappings
mtd: call of_platform_populate() for MTD partitions
mtd: rawnand: renesas: Use runtime PM instead of the raw clock API
dt-bindings: mtd: renesas: Fix the NAND controller description
mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed
mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed
mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()
mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4
mtd: spi-nor: debugfs: fix format specifier
mtd: spi-nor: support eon en25qh256a variant
mtd: spi-nor: winbond: add support for W25Q512NW-IM
mtd: spi-nor: expose internal parameters via debugfs
mtd: spi-nor: export spi_nor_hwcaps_pp2cmd()
mtd: spi-nor: move spi_nor_write_ear() to winbond module
mtd: spi-nor: amend the rdsr dummy cycles documentation
mtd: cfi_cmdset_0002: Rename chip_ready variables
...
-----BEGIN PGP SIGNATURE-----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=0Rw1
-----END PGP SIGNATURE-----
Merge tag 'for-5.19/block-2022-05-22' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"Here are the core block changes for 5.19. This contains:
- blk-throttle accounting fix (Laibin)
- Series removing redundant assignments (Michal)
- Expose bio cache via the bio_set, so that DM can use it (Mike)
- Finish off the bio allocation interface cleanups by dealing with
the weirdest member of the family. bio_kmalloc combines a kmalloc
for the bio and bio_vecs with a hidden bio_init call and magic
cleanup semantics (Christoph)
- Clean up the block layer API so that APIs consumed by file systems
are (almost) only struct block_device based, so that file systems
don't have to poke into block layer internals like the
request_queue (Christoph)
- Clean up the blk_execute_rq* API (Christoph)
- Clean up various lose end in the blk-cgroup code to make it easier
to follow in preparation of reworking the blkcg assignment for bios
(Christoph)
- Fix use-after-free issues in BFQ when processes with merged queues
get moved to different cgroups (Jan)
- BFQ fixes (Jan)
- Various fixes and cleanups (Bart, Chengming, Fanjun, Julia, Ming,
Wolfgang, me)"
* tag 'for-5.19/block-2022-05-22' of git://git.kernel.dk/linux-block: (83 commits)
blk-mq: fix typo in comment
bfq: Remove bfq_requeue_request_body()
bfq: Remove superfluous conversion from RQ_BIC()
bfq: Allow current waker to defend against a tentative one
bfq: Relax waker detection for shared queues
blk-cgroup: delete rcu_read_lock_held() WARN_ON_ONCE()
blk-throttle: Set BIO_THROTTLED when bio has been throttled
blk-cgroup: Remove unnecessary rcu_read_lock/unlock()
blk-cgroup: always terminate io.stat lines
block, bfq: make bfq_has_work() more accurate
block, bfq: protect 'bfqd->queued' by 'bfqd->lock'
block: cleanup the VM accounting in submit_bio
block: Fix the bio.bi_opf comment
block: reorder the REQ_ flags
blk-iocost: combine local_stat and desc_stat to stat
block: improve the error message from bio_check_eod
block: allow passing a NULL bdev to bio_alloc_clone/bio_init_clone
block: remove superfluous calls to blkcg_bio_issue_init
kthread: unexport kthread_blkcg
blk-cgroup: cleanup blkcg_maybe_throttle_current
...
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmKD51AACgkQJWrqGEe9
VoQJ8AgAo8qjO5QQmd76v1q1Regxxl7RsH7hr7r9gJfgTwzhQC/xIyTiorcVPG7B
UDNu4Dwe3OAPbmU54TQNS/AMQkgHGMcIRTVut8+oL+ZnjYl+gv261GxmsfxaK/Hu
Vvvq9X0iyaKpZfyq3uksbsxiXbwMn4fHT7Reaimc9Thw+XKD7AcYWCuFb9GAWfaf
XQUVLg6y4Qk4BR9ZpYAx2v5FH4amJV9RKKTIqiymwcjnBZjYOI29wgKwY1hX+3bm
2Wu4wcccWhDzlV0Casf/hIGBydKx3omV+cJHLtmx7s+dqPvYSUGuvR2nbq5wuMqp
ZcAYeRhGEAYMYcMB/QuKmh4g/Js26w==
=QyqB
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.19' into mtd/next
NAND core:
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Read back written SR value to make sure the write was done correctly.
- Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQTlUWNzXGEo3bFmyIR4drqP028CQUCYoH1/QAKCRAR4drqP028
CXQeAP9hAfNGV55cOsd+z+3+xOxKeAYN/PC7UmXSvFgJZKYEqgEA/UF+SwsrOTyd
x+5UwNSOvrUX404j6ROP0kH4/kzARAY=
=Krne
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.19' into mtd/next
SPI NOR core changes:
- Read back written SR value to make sure the write was done correctly.
- Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Clock source is prepared and enabled by clk_prepare_enable()
in probe function, but not disabled or unprepared in remove
function.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220516092911.953066-1-yangyingliang@huawei.com
Currently phram always uses ioremap(), but this is unnecessary when
normal memory is used. If the reserved-memory node does not specify the
no-map property, indicating it should be mapped as system RAM and
ioremap() cannot be used on it, use a cached mapping using
memremap(MEMREMAP_WB) instead.
On one of my systems this improves read performance by ~70%.
(Note that this driver has always used normal memcpy/memset functions on
memory obtained from ioremap(), which sparse doesn't like. There is no
memremap() variant which maps exactly to ioremap() on all architectures,
so that behaviour of the driver is not changed to avoid affecting
existing users, but the sparse warnings are suppressed in the moved code
with __force.)
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220510151822.1809278-1-vincent.whitchurch@axis.com
Until this change MTD subsystem supported handling partitions only with
MTD partitions parsers. That's a specific / limited API designed around
partitions.
Some MTD partitions may however require different handling. They may
contain specific data that needs to be parsed and somehow extracted. For
that purpose MTD subsystem should allow binding of standard platform
drivers.
An example can be U-Boot (sub)partition with environment variables.
There exist a "u-boot,env" DT binding for MTD (sub)partition that
requires an NVMEM driver.
Ref: 5db1c2dbc0 ("dt-bindings: nvmem: add U-Boot environment variables binding")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220510131259.555-1-zajec5@gmail.com
This NAND controller is part of a well defined power domain handled by
the runtime PM core. Let's keep the harmony with the other RZ/N1 drivers
and exclusively use the runtime PM API to enable/disable the clocks.
We still need to retrieve the external clock rate in order to derive the
NAND timings, but that is not a big deal, we can still do that in the
probe and just save this value to reuse it later.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/linux-mtd/20220513104957.257721-3-miquel.raynal@bootlin.com
All code in clk_disable_unprepare() already checks the clk ptr using
IS_ERR_OR_NULL so there is no need to check it again before calling it.
A lot of other drivers already rely on this behaviour, so it's safe
to do so here.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220512185033.46901-1-phil.edworthy@renesas.com
All code in clk_disable_unprepare() already checks the clk ptr using
IS_ERR_OR_NULL so there is no need to check it again before calling it.
A lot of other drivers already rely on this behaviour, so it's safe
to do so here.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220512184558.45966-1-phil.edworthy@renesas.com
This SPI driver adds support for the Aspeed static memory controllers
of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.
* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.
* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver
. single, dual mode.
* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.
* AST2400 New Static Memory Controller (also referred as FMC)
. BMC firmware
. New register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
. single, dual and quad mode.
Each controller has a memory range on which flash devices contents are
mapped. Each device is assigned a window that can be changed at bootime
with the Segment Address Registers.
Each SPI flash device can then be accessed in two modes: Command and
User. When in User mode, SPI transfers are initiated with accesses to
the memory segment of a device. When in Command mode, memory
operations on the memory segment of a device generate SPI commands
automatically using a Control Register for the settings.
This initial patch adds support for User mode. Command mode needs a little
more work to check that the memory window on the AHB bus fits the device
size. It will come later when support for direct mapping is added.
Single and dual mode RX transfers are supported. Other types than SPI
are not supported.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The MediaTek Hardware ECC Engine is only present on MediaTek MT27xx and
MT76xx SoCs. The driver for this engine is a dependency for the
MediaTek NAND controller (MTD_NAND_MTK) and the MediaTek SPI NAND Flash
Interface (SPI_MTK_SNFI) drivers, both of which already depend on
ARCH_MEDIATEK.
Hence add a dependency on ARCH_MEDIATEK to the Hardware ECC Engine
driver, too, to prevent asking the user about this driver when
configuring a kernel without MediaTek SoC support.
Fixes: 4fd62f15af ("mtd: nand: make mtk_ecc.c a separated module")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/bb9568e825d4bc7506870b03836baa91bcc4b725.1652104136.git.geert+renesas@glider.be
Add timings for Kioxia/Toshiba TH58NVG3S0HBAI4. Timings
for this memory matches the timings selected for
TH58NVG2S3HBAI4.
This patch increases eraseblock write speed from 5248 KiB/s
to 6864 KiB/s and erase block read speed from 8542 KiB/s
to 18360 KiB/s
Tested on i.MX6SX.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220429083931.26795-1-rickaran@axis.com
The intention was to print the JEDEC ID in the following format:
nn nn nn
In this case format specifier has to be "%*ph". Fix it.
Fixes: 0257be79fc ("mtd: spi-nor: expose internal parameters via debugfs")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220512112027.3771734-1-michael@walle.cc
This patch allows accessing the upper 16m on the A variant (EN25QH256A) of
the EN25QH256 that shares same JEDEC ID.
Without this patch, addr_with is detected to be '4' but the read_opcode is
a plain READ (supporting only 3 byte addresses).
Setting PARSE_SFDP is enough to detect the read_opcode READ_4B on the A
variant. READ_4B is not available on the no-A variant.
Both variants support 4-byte address mode (spi_nor_set_4byte_addr_mode)
but that is prone to breaking on unexpected reboots if the reset pin isn't
connected (broken-flash-reset).
The no-A variant supports a 'high bank latch mode' that affects read,
program, and erase commands - similar to the extended address register
(EAR).
The HBL bit is manipulated using the ENHBL (0x67) and EXHBL (0x98)
opcodes.
Should it become necessary to distinguish the two variants in the future,
the A variant sets the SNOR_HWCAPS_READ_1_1_4 SFDP param - the no-A
variant doesn't.
Tested with and without fast read on the A variant only.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220502233310.791565-2-leon@georgemail.eu
There is no way to gather all information to verify support for a new
flash chip. Also if you want to convert an existing flash chip to the
new SFDP parsing, there is not enough information to determine if the
flash will work like before. To ease this development, expose internal
parameters via the debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-2-michael@walle.cc
The "Extended Address Register" is winbond specific. If the flash is
larger than 16MiB and is used in 3 byte address mode, it is used to set
the remaining address bits. Move the write_ear() function, the opcode
macros and the spimem op template into the winbond module and rename
them accordingly.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429100153.2338501-1-michael@walle.cc
The rdsr dummy cycles are only used by the 8d-8d-8d mode. Mention that
in the documentation.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220418112837.2792242-1-michael@walle.cc
Since commit dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to
check correct value") buffered writes fail on S29GL064N. This is
because, on S29GL064N, reads return 0xFF at the end of DQ polling for
write completion, where as, chip_good() check expects actual data
written to the last location to be returned post DQ polling completion.
Fix is to revert to using chip_good() for S29GL064N which only checks
for DQ lines to settle down to determine write completion.
Link: https://lore.kernel.org/r/b687c259-6413-26c9-d4c9-b3afa69ea124@pengutronix.de/
Fixes: dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
Cc: stable@vger.kernel.org
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220323170458.5608-3-ikegami.t@gmail.com
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmJpa+MACgkQJWrqGEe9
VoTVPwf+PjOPS9MH+3wQkEsqwHtJyC9dvfTRWNSkzJEos0710jl6peeWjo1ift1A
4JLMI3TGHWbNqBykpSLxZPVc6X/toGoMz6/2OussnYQBYgXjLNOgWQqS4kZZmK7D
BARpke8TTqglJyat7NpGNo1EGWA4EtYqwvoPT+H0LMLQbe/NQD0k4RaRNpw+BwPq
gaBHZf/CmN4oG0QrPPvS7jrm0dgWrQgTqRf9zzOnml3m22q3PGMnmY1A1CunBsFn
HK+GxYUOeemPc40mET+U1x6O0+VNlxW2KQ+fZoNHnljd55zq1Cp4mXfr7KuFgfDK
4xMAAoI5cMp8kpLLVUBlD4uzOj3fow==
=FBXD
-----END PGP SIGNATURE-----
Merge tag 'mtd/mtk-spi-nand-for-5.19' into nand/next
Mediatek ECC changes:
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The recently added ECC engine support introduced a generic property
named nand-ecc-engine for ecc engine phandle. This patch adds support
for this new property.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220424032527.673605-4-gch981213@gmail.com
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-2-yangyingliang@huawei.com
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-1-yangyingliang@huawei.com
Writing volatile registers are instant according to Micron and do not
need any status polling. Remove status polling on volatile registers write.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-12-tudor.ambarus@microchip.com
Writing volatile registers are instant according to Cypress and do not
need any status polling. Remove status polling on volatile registers write.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-11-tudor.ambarus@microchip.com
Clean the op declaration and hide the details of each op. With this it
results a cleanner, easier to read code. No functional change expected.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220420103427.47867-10-tudor.ambarus@microchip.com
Introduce template operation to remove code duplication.
Split spi_nor_cypress_octal_dtr_enable() in
spi_nor_cypress_octal_dtr_ena() spi_nor_cypress_octal_dtr_dis() as it no
longer made sense to try to keep everything alltogether: too many
"if (enable)" throughout the code, which made the code difficult to read.
Add debug messages in case spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-9-tudor.ambarus@microchip.com
Introduce template operation to remove code duplication.
Split spi_nor_micron_octal_dtr_enable() in spi_nor_micron_octal_dtr_en()
and spi_nor_micron_octal_dtr_dis() as it no longer made sense to try to
keep everything alltogether: too many "if (enable)" throughout the code,
which made the code difficult to follow. Add dev_dbg messages in case
spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-8-tudor.ambarus@microchip.com
There are manufacturers that use registers indexed by address. Some of
them support "read/write any register" opcodes. Provide core methods that
can be used by all manufacturers. SPI NOR controller ops are intentionally
not supported as we intend to move all the SPI NOR controller drivers
under the SPI subsystem.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-7-tudor.ambarus@microchip.com
Use spi_nor_read_id() core method to avoid duplication of code. Now the ID
is read on the full SPI_NOR_MAX_ID_LEN instead of
round_up(nor->info->id_len, 2), but it doesn't harm to read more ID bytes,
so the change comes with no secondary effects. dev_dbg messages in case
spi_nor_read_id() fails, will be added in a further patch after we split
the octal DTR enable/disable methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-6-tudor.ambarus@microchip.com
RDID is used in the core to auto detect the flash, but also by some
manufacturer drivers that contain flashes that support Octal DTR mode,
so that they can read the flash ID after the switch to Octal DTR was made
to test if the switch was successful. Introduce a core method for RDID op
to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-5-tudor.ambarus@microchip.com
In case spi_nor_match_name() returned NULL, the auto detection was
issued twice. There's no reason to try to detect the same chip twice,
do the auto detection only once.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-4-tudor.ambarus@microchip.com
Similar to spi_nor_match_name() extend the search of flash_info through
all the manufacturers, this time doing the match by ID. There's no reason
to limit the search per manufacturer yet, do it globally, search the flash
in all the parts of all manufacturers in a single method.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-3-tudor.ambarus@microchip.com
The method is matching a flash_info entry by searching by name. Rename
the method for better clarity.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-2-tudor.ambarus@microchip.com
Read back Status Register 1 to ensure that the written byte match the
received value and return -EIO if read back test failed.
Without this patch, spi_nor_write_16bit_sr_and_check() only check the
second half of the 16bit. It causes errors like spi_nor_sr_unlock()
return success incorrectly when spi_nor_write_16bit_sr_and_check()
doesn't write SR successfully.
Fixes: 39d1e3340c ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220126073227.3401275-1-chentsung@chromium.org
Create a dump header to enable the addition of fields without having
to modify the rest of the code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jean-Marc Eurin <jmeurin@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220421234244.2172003-3-jmeurin@google.com
The read buffer size depends on the MTDOOPS_HEADER_SIZE.
Tested: Changed the header size, it doesn't panic, header is still
read/written correctly.
Signed-off-by: Jean-Marc Eurin <jmeurin@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220421234244.2172003-2-jmeurin@google.com
Warning on every translated mtd partition results in excessive log noise
if this driver is loaded:
nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
nand: Macronix MX30LF1G18AC
nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
read_bbt: found bbt at block 1023
10 fixed-partitions partitions found on MTD device mt7621-nand
Creating 10 MTD partitions on "mt7621-nand":
0x000000000000-0x000000080000 : "Bootloader"
mtdblock: MTD device 'Bootloader' is NAND, please consider using UBI block devices instead.
0x000000080000-0x000000100000 : "Config"
mtdblock: MTD device 'Config' is NAND, please consider using UBI block devices instead.
0x000000100000-0x000000140000 : "Factory"
mtdblock: MTD device 'Factory' is NAND, please consider using UBI block devices instead.
0x000000140000-0x000002000000 : "Kernel"
mtdblock: MTD device 'Kernel' is NAND, please consider using UBI block devices instead.
0x000000540000-0x000002000000 : "ubi"
mtdblock: MTD device 'ubi' is NAND, please consider using UBI block devices instead.
0x000002140000-0x000004000000 : "Kernel2"
mtdblock: MTD device 'Kernel2' is NAND, please consider using UBI block devices instead.
0x000004000000-0x000004100000 : "wwan"
mtdblock: MTD device 'wwan' is NAND, please consider using UBI block devices instead.
0x000004100000-0x000005100000 : "data"
mtdblock: MTD device 'data' is NAND, please consider using UBI block devices instead.
0x000005100000-0x000005200000 : "rom-d"
mtdblock: MTD device 'rom-d' is NAND, please consider using UBI block devices instead.
0x000005200000-0x000005280000 : "reserve"
mtdblock: MTD device 'reserve' is NAND, please consider using UBI block devices instead.
mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
This is more likely to annoy than to help users of embedded distros where
this driver is enabled by default. Making the blockdevs available does
not imply that they are in use, and warning about bootloader partitions
or other devices which obviously never will be mounted is more confusing
than helpful.
Move the warning to open(), where it will be of more use - actually warning
anyone who mounts a file system on NAND using mtdblock.
Fixes: e07403a8c6 ("mtdblock: Warn if added for a NAND device")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220328161108.87757-1-bjorn@mork.no
Allow phram to be probed from the devicetree. It expects to be in a
reserved-memory node as documented by the bindings. This allows things
like partitioning to be specified via the devicetree.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412135302.1682890-4-vincent.whitchurch@axis.com
Allow the MTD index to be specified via a devicetree alias, so that the
number does not just depend on probe order. This is useful to allow
pseudo-devices like phram to be optionally used on systems, without
having this affect the numbering of the real hardware MTD devices.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412135302.1682890-2-vincent.whitchurch@axis.com
This custom maps driver was never used with the device tree
enabled IXP4xx systems, which use the physmap add-on from
commit 2aba2f2a70
("mtd: physmap_of: add a hook for Intel IXP4xx flash probing")
Since kernel v5.18-rc1 IXP4xx is only booting from the device
tree so drop this old driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220407210844.2489682-1-linus.walleij@linaro.org
The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 bytes OOB. This adds a static NAND ID entry to correct this.
Tested on FRITZ!Box 7530 flashed with OpenWrt.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220420104034.6333-1-dev@aboehler.at
The code change proposes a new way to set bch geometry for large oob
NAND (oobsize > 1KB). In this case, previous implementation can NOT
guarantee the bad block mark always locates in data chunk, so we need a
new way to do it. The general idea is,
1.Try all ECC strength from the maximum ecc that controller can support
to minimum value required by NAND chip, any ECC strength makes the
BBM locate in data chunk can be eligible.
2.If none of them works, using separate ECC for meta, which will add
one extra ecc with the same ECC strength as other data chunks. This
extra ECC can guarantee BBM located in data chunk, also we need to
check if oob can afford it.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-6-han.xu@nxp.com
There is only one variable ecc_chunk_size in bch_geometry data
structure but two different field in BCH registers. The data0_size in
BCH_FLASH0LAYOUT0 and datan_size in BCH_FLASH0LAYOUT1 should have
dedicate variable since they might set to different values in some
cases. For instance, if need dedicate ecc for meta area, the data0_size
should be 0 rather than datan_size, but for all other cases, data0_size
still equals to datan_size and it won't bring any function change.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-5-han.xu@nxp.com
Add nand_ecc_is_strong_enough() check in gpmi_check_ecc() function to
make sure ecc strength can meet chip requirement.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-3-han.xu@nxp.com
The code change refactor the bch geometry setting function, which
doesn't change the default behavior, while user may choose to use chips
required minimum ecc strength by DT flag "fsl,use-minimum-ecc".
The default way to set bch geometry need to set the data chunk
size(step_size) larger than oob size to make sure BBM locates in data
chunk, then set the maximum ecc strength oob can hold. It always use
unbalanced ECC layout, which ecc0 will cover both meta and data0 chunk.
But the default bch setting is deprecated for large oobsize NAND
(oobsize >1KB), so in the patch set, there is a split commit that
introduces a new way to set bch geometry for large oob size NAND.
For all other cases,set the bch geometry by chip required strength and
step size, which uses the minimum ecc strength chip required. It can be
explicitly enabled by DT flag "fsl,use-minimum-ecc", but need to be
en/disabled in both u-boot and kernel at the same time.
Signed-off-by: Han Xu <han.xu@nxp.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-2-han.xu@nxp.com
All of the resources used by this driver has managed interfaces, so use
them. Otherwise we will get the following splat:
[ 4.472703] denali-nand-pci 0000:00:05.0: timeout while waiting for irq 0x1000
[ 4.474071] denali-nand-pci: probe of 0000:00:05.0 failed with error -5
[ 4.473538] nand: No NAND device found
[ 4.474068] BUG: unable to handle page fault for address: ffffc90005000410
[ 4.475169] #PF: supervisor write access in kernel mode
[ 4.475579] #PF: error_code(0x0002) - not-present page
[ 4.478362] RIP: 0010:iowrite32+0x9/0x50
[ 4.486068] Call Trace:
[ 4.486269] <IRQ>
[ 4.486443] denali_isr+0x15b/0x300 [denali]
[ 4.486788] ? denali_direct_write+0x50/0x50 [denali]
[ 4.487189] __handle_irq_event_percpu+0x161/0x3b0
[ 4.487571] handle_irq_event+0x7d/0x1b0
[ 4.487884] handle_fasteoi_irq+0x2b0/0x770
[ 4.488219] __common_interrupt+0xc8/0x1b0
[ 4.488549] common_interrupt+0x9a/0xc0
Fixes: 93db446a42 ("mtd: nand: move raw NAND related code to the raw/ subdir")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220411125808.958276-1-zheyuma97@gmail.com
This patch fixes a memory corruption that occurred in the
nand_scan() path for Hynix nand device.
On boot, for Hynix nand device will panic at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual
address 00000070
| [00000070] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0
#38
| Hardware name: Generic DT based system
| PC is at nandc_set_reg+0x8/0x1c
| LR is at qcom_nandc_command+0x20c/0x5d0
| pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113
| sp : c14adc50 ip : c14ee208 fp : c0cc970c
| r10: 000000a3 r9 : 00000000 r8 : 00000040
| r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040
| r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040
| Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Register r0 information: slab kmalloc-2k start c14ee000 pointer offset
64 size 2048
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| nandc_set_reg from qcom_nandc_command+0x20c/0x5d0
| qcom_nandc_command from nand_readid_op+0x198/0x1e8
| nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78
| hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454
| hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8
| nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0
| qcom_nandc_probe from platform_probe+0x58/0xac
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size.
This causes the sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_command() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page
size in qcom_nand_attach_chip call back after freeing the previously
allocated memory for bam txn as per nandc->max_cwperpage = 1 and then
again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on
page size in qcom_nand_attach_chip call back itself.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f1 ("mtd: rawnand: qcom: convert driver to nand_scan()")
Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 83738d87e3 ("mtd: sh_flctl: Add DMA capabilty")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com
The mach/hardware.h is included in lots of places, and it provides
three different things on pxa:
- the cpu_is_pxa* macros
- an indirect inclusion of mach/addr-map.h
- the __REG() and io_pv2() helper macros
Split it up into separate <linux/soc/pxa/cpu.h> and mach/pxa-regs.h
headers, then change all the files that use mach/hardware.h to
include the exact set of those three headers that they actually
need, allowing for further more targeted cleanup.
linux/soc/pxa/cpu.h can remain permanently exported and is now in
a global location along with similar headers. pxa-regs.h and
addr-map.h are only used in a very small number of drivers now
and can be moved to arch/arm/mach-pxa/ directly when those drivers
are to pass the necessary data as resources.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-leds@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Just use a non-zero max_discard_sectors as an indicator for discard
support, similar to what is done for write zeroes.
The only places where needs special attention is the RAID5 driver,
which must clear discard support for security reasons by default,
even if the default stacking rules would allow for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> [drbd]
Acked-by: Jan Höppner <hoeppner@linux.ibm.com> [s390]
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220415045258.199825-25-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
According to the datasheet, mt7622 only has 5 ECC capabilities instead
of 7, and the decoding error register is arranged as follows:
+------+---------+---------+---------+---------+
| Bits | 19:15 | 14:10 | 9:5 | 4:0 |
+------+---------+---------+---------+---------+
| Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 |
+------+---------+---------+---------+---------+
This means err_mask should be 0x1f instead of 0x3f and the number of
bits shifted in mtk_ecc_get_stats should be 5 instead of 8.
This commit introduces err_shift for the difference in this register
and fix other existing parameters.
Public MT7622 reference manual can be found on [0] and the info this
commit is based on is from page 656 and page 660.
[0]: https://wiki.banana-pi.org/Banana_Pi_BPI-R64#Documents
Fixes: 98dea8d719 ("mtd: nand: mtk: Support MT7622 NAND flash controller.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220402160315.919094-1-gch981213@gmail.com
This makes printed info consistent with other kernel messages. After
scanning NAND BBT create_bbt() prints offset of each bad block. This
change makes is easy to verify nand_erase_nand() failure reason.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220326163304.30806-1-zajec5@gmail.com
Add support for:
GD5F{1,2}GM7{U,R}ExxG
GD5F4GM8{U,R}ExxG
These are new 27nm counterparts for the GD5FxGQ4 chips from GigaDevice
with 8b/512b on-die ECC capability.
These chips (and currently supported GD5FxGQ5 chips) have QIO DTR
instruction for reading page cache. It isn't added in this patch because
I don't have a DTR spi controller for testing.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220320100001.247905-6-gch981213@gmail.com
Add support for:
GD5F2GQ5{U,R}ExxG
GD5F4GQ6{U,R}ExxG
These chips uses 4 dummy bytes for quad io and 2 dummy bytes for dual io.
Besides that and memory layout, they are identical to their 1G variant.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220320100001.247905-5-gch981213@gmail.com
Add support for:
GD5F1GQ4RExxG
GD5F2GQ4{U,R}ExxG
These chips differ from GD5F1GQ4UExxG only in chip ID, voltage
and capacity.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220320100001.247905-3-gch981213@gmail.com
JFFS2:
- Fixes for various memory issues
UBI:
- Fix for a race condition in cdev ioctl handler
UBIFS:
- Fixes for O_TMPFILE and whiteout handling
- Fixes for various memory issues
-----BEGIN PGP SIGNATURE-----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=ZU5j
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Fixes for various memory issues
UBI:
- Fix for a race condition in cdev ioctl handler
UBIFS:
- Fixes for O_TMPFILE and whiteout handling
- Fixes for various memory issues"
* tag 'for-linus-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: rename_whiteout: correct old_dir size computing
jffs2: fix memory leak in jffs2_scan_medium
jffs2: fix memory leak in jffs2_do_mount_fs
jffs2: fix use-after-free in jffs2_clear_xattr_subsystem
fs/jffs2: fix comments mentioning i_mutex
ubi: fastmap: Return error code if memory allocation fails in add_aeb()
ubifs: Fix to add refcount once page is set private
ubifs: Fix read out-of-bounds in ubifs_wbuf_write_nolock()
ubifs: setflags: Make dirtied_ino_d 8 bytes aligned
ubifs: Rectify space amount budget for mkdir/tmpfile operations
ubifs: Fix 'ui->dirty' race between do_tmpfile() and writeback work
ubifs: Rename whiteout atomically
ubifs: Add missing iput if do_tmpfile() failed in rename whiteout
ubifs: Fix wrong number of inodes locked by ui_mutex in ubifs_inode comment
ubifs: Fix deadlock in concurrent rename whiteout and inode writeback
ubifs: rename_whiteout: Fix double free for whiteout_ui->data
ubi: Fix race condition between ctrl_cdev_ioctl and ubi_cdev_ioctl
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
* Replace the expert mode symbols with a single helper
* Fix misuses of of_match_ptr()
* Remove partid and partname debugfs files
* tests: Fix eraseblock read speed miscalculation for lower partition sizes
* TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
* spear_smi: use GFP_KERNEL
* mchp48l640: Add SPI ID table
* mchp23k256: Add SPI ID table
* blkdevs: Avoid soft lockups with some mtd/spi devices
* aspeed-smc: Improve probe resilience
Hyperbus changes:
* HBMC_AM654 should depend on ARCH_K3
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
* Fix misuses of of_match_node()
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI NOR core changes:
* Move vendor specific code out of the core into vendor drivers.
* Unify all function and object names in the vendor modules.
* Make setup() callback optional to improve readability.
* Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
* Dropped mtd/cortina,gemini-flash.txt
* Convert BCM47xx partitions to json-schema
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI7WJcACgkQJWrqGEe9
VoSzpAgAutzRv9TRUiXdBGGlJ851QaZ6ZUvT1bHKTQA+xZi+MZyNmc0cWNg3B70I
PnwyxNAmRkUQKwV5Vgy/sQrt42qZnPmr+8XMq+UiziPmgFdjiTdLqGcN619Hi12t
JqtoKL828R064LSEq5nWsJ2waoGT1nNtZK8kA2qe8ctvmH0YTThriVZUQR4/Befb
OGFheceLFycE/vkktPPr3As4603fMiyDOT7EA3Mtzgjohry0a0TqoakHCaHC/fYo
0/h+x+jJATPtgbWm1ZiV3cZ/Su00+rKuQOsiAWvM/pqDaijsVntBmtK0PRtums2Q
m8LCspuQYNnCINeQXqba9RxACpibDg==
=+6Zk
-----END PGP SIGNATURE-----
Merge tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI021sACgkQJWrqGEe9
VoTEcggAiFXD+oR0VXTsykiNDiopsAUZwLPGuqk8gvD4ozOYCoAEoYrtnBM6Uybz
W6Hu6Eow/ri1H+uVygUw3RYa4TpxrZrmZnJ1YimXxZjbLYjgE3FS9vzh2l4Bu3yo
fkkQH+nFvk9qVIK8qolAny+LWl37gkSnCd6mPPksYaG5Ds1n1ZgyTZVUz5TOWAjG
QAWUQQfO1iu7+u4CXa9JRTkCf55bT6v6c9Ryq6MA+ok6jVRN6Cj9WhxHtCB5vmOH
Ndmu4V8BqaNKg39ltolqSPuwt3GEh707LRr+YakfnaOM7Sf8E/evn/THSkHwY/yn
bAjpU1gvS13nJ++s8nHwIhHKhoYjTg==
=4Uke
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.18' into mtd/next
Raw NAND core changes:
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus types,
causing updates to most SPI device drivers. The branch with that on has
been cross merged with a couple of other trees which added new SPI
drivers this cycle, I'm not expecting any build issues resulting from
the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmI4b+8ACgkQJNaLcl1U
h9AB+Qf/WhPzDSCdhK1repnSmEpRNs/J6hItmY2H6pTQaWALpfTB0+p1Nb5tAotg
fHbu6a2AsiiwWt+tDal44GFYhS0CDSOT4hqgLV8msyDDPPJqqr7A2dbu7YrCjTVI
TgNZNwxW7c2LgqBXR9GV7NPWYoxYxveoYh+L+05MSuSQxSOvPl6LUZiZPnPufQM6
dCpEh19atrtasFg3rFnslWBd2C3h8hb6YT7vUZs9gxhg3FvSgpYQwzz5SfFgHXK6
Rg07m8fDTSjf2qo1C4pc/d1Ni1xBe7aHKMtjtR3jJ4q8QqiawfCcvvOep/Iaec1+
s3qnDthohWMJoF1W6ERf3HiAgNIfhg==
=4tlR
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmInffUACgkQS1VPR6WN
FOn9fwf/SCIvgoScBNeQjW4cGTmh11oO+O8i2umibq0pQDLrNF6Ul7ykY6Fdm4Dc
+Ce7c4Vp0O+DRphIkaK5MtNgRmXMOQbqUKcNAQftFS0wCtJ+QVQzOvkVGS3jQA74
KVEY3Jiup3Q5qknBg0r890ENwRLmcGJaPi5DAO+uHcf6ItTpwjv3z6C2ZUeiH6UK
PMSwZgd86dwwH2eU4G5EoAjA+nqOcVvH0V1F49DFsGZ3kkmUS6nMNnSpb5SykszT
4uq+7+c3E2UOC0TlUkyX/xTv4DoZZDi6qqVEaV14bELL1a0FdltjKyIuWTds1Tei
rwPhEOkqOpSnBVjlUWb7icwef21NWg==
=QFe+
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.18' into mtd/next
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Avoid random build errors with architectures which do not select
HAS_IOMEM by depending on it in Kconfig.
This fixes the following warning:
/home/mraynal/0day/gcc-11.2.0-nolibc/s390-linux/bin/s390-linux-ld:
drivers/mtd/nand/ecc-mxic.o: in function `mxic_ecc_probe':
ecc-mxic.c:(.text+0x2244): undefined reference to `devm_platform_ioremap_resource'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220314152336.75447-1-miquel.raynal@bootlin.com
Don't populate the read-only arrays possible_strength and
spare_size on the stack but instead make them static
const. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220307230940.169235-1-colin.i.king@gmail.com
The AM65x HyperBus controller is only present on Texas Instruments AM65x
SoCs. Hence add a dependency on ARCH_K3, to prevent asking the user
about this driver when configuring a kernel without support for the
Texas Instruments Inc. K3 multicore SoC architecture.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/9fd6b975adba710158f28aa603cf87a6d189a418.1646655894.git.geert+renesas@glider.be
partid and partname debugfs files were used just by SPI NOR, but they were
replaced by sysfs entries. Since these debugfs files are no longer used in
mtd, remove dead code. The directory is kept as it is used by nandsim,
mtdswap and docg3.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220225144656.634682-1-tudor.ambarus@microchip.com
While calculating speed during mtd_speedtest, the time interval
(i.e., start - finish) is rounded off to the nearest milliseconds by
ignoring the fractional part. This leads to miscalculation of speed.
The miscalculation is more visible while running speed test on small
partition sizes(i.e., when partition size is equal to eraseblock size or
twice the eraseblock size) at higher spi frequencies.
For e.g., while calculating eraseblock read speed for a mtd partition with
size equal to the eraseblock size(i.e., 64KiB) the eraseblock read time
interval comes out to be 966490 nanosecond. This is then converted to
millisecond(i.e., 0.966 msec.). The integer part (i.e., 0 msec) of the
value is considered and the fractional part (i.e., 0.966) is ignored,for
calculating the eraseblock read speed. So the reported eraseblock read
speed is 0 KiB/s, which is incorrect.
There are two approaches to fix this issue.
First approach will be to keep the time interval in millisecond. and round
up the integer value, with this approach the 0.966msec time interval in the
above example will be rounded up to 1msec and this value is used for
calculating the speed. Downside of this approach is that the reported speed
is still not accurate.
Second approach will be to convert the time interval to microseconds
instead of milliseconds, with this approach the 966490 nanosecond time
interval in the above example will be converted t0 966.490usec and this
value is used for calculating the speed. As compared to the current
implementation and the suggested First approach, this approach will report
a more accurate speed. Downside of this approach is that, in future if the
mtd size is too large then the u64 variable, that holds the number of
bytes, might overflow.
In this patch we have gone with the second approach as this reports a more
accurate speed. With this approach the eraseblock read speed in the above
example comes out to be 132505 KiB/s when the spi clock is configured at
150Mhz.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220208103905.13354-1-amit.kumar-mahapatra@xilinx.com
The reference counting issue happens in several error handling paths
on a refcounted object "nc->dmac". In these paths, the function simply
returns the error code, forgetting to balance the reference count of
"nc->dmac", increased earlier by dma_request_channel(), which may
cause refcount leaks.
Fix it by decrementing the refcount of specific object in those error
paths.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Co-developed-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Co-developed-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220304085330.3610-1-xiongx18@fudan.edu.cn
Even if SPI_NOR_NO_ERASE was set, one could still send erase opcodes
to the flash. It is not recommended to send unsupported opcodes to
flashes. Fix the logic and do not set mtd->_erase when SPI_NOR_NO_ERASE
is specified. With this users will not be able to issue erase opcodes to
flashes and instead they will recive an -ENOTSUPP error.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220228163334.277730-1-tudor.ambarus@microchip.com
The root of the problem is that we are selecting symbols that have
dependencies. This can cause random configurations that can fail.
The cleanest solution is to avoid using select.
This driver uses interfaces from the OMAP_GPMC driver so we have to
depend on it instead.
Fixes: 4cd335dae3 ("mtd: rawnand: omap2: Prevent invalid configuration and build error")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/linux-mtd/20220219193600.24892-1-rogerq@kernel.org
Here are a few small driver fixes for 5.17-rc6 for reported issues. The
majority of these are IIO fixes for small things, and the other two are
a mvmem and mtd core conflict fix.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYhjVGA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymtYQCgwSOl1N4iPmv2lpaHmofd+BF4frgAn1DJ0q/A
OCG5siwdf3wMxPjL9HIC
=AUOQ
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few small driver fixes for 5.17-rc6 for reported issues.
The majority of these are IIO fixes for small things, and the other
two are a mvmem and mtd core conflict fix.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mtd: core: Fix a conflict between MTD and NVMEM on wp-gpios property
nvmem: core: Fix a conflict between MTD and NVMEM on wp-gpios property
iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot
iio: Fix error handling for PM
iio: addac: ad74413r: correct comparator gpio getters mask usage
iio: addac: ad74413r: use ngpio size when iterating over mask
iio: addac: ad74413r: Do not reference negative array offsets
iio: adc: men_z188_adc: Fix a resource leak in an error handling path
iio: frequency: admv1013: remove the always true condition
iio: accel: fxls8962af: add padding to regmap for SPI
iio:imu:adis16480: fix buffering for devices with no burst mode
iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits
iio: adc: tsc2046: fix memory corruption by preventing array overflow
As we have deleted some flag, lets renumber them so there are no holes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-33-michael@walle.cc
Now that there is almost no special case code left in
spi_nor_sr_ready(), the return check looks odd. Move the function call
closer to the return code checking.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-32-michael@walle.cc
Drop the generic spi_nor prefix for all the spansion functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-31-michael@walle.cc
Now that all functions using that flag are local to the spansion module,
we can convert the flag to a manufacturer one.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-30-michael@walle.cc
The clear status register flags is only available on spansion flashes.
Move all the functions around that into the spanion module.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-29-michael@walle.cc
Don't return early when the flash is smaller than or equal to 16MiB. We
need to be able to register hooks for all sizes of flashes. This also has
the benefit that it increases the readability of the code because the
action, i.e. registering the fixups, is connected to the condition, i.e.
flashes larger than 16MiB.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-28-michael@walle.cc
Drop the generic spi_nor prefix for all the micron-st functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-27-michael@walle.cc
Now that all functions using that flag are local to the micron module,
we can convert the flag to a manufacturer one.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-26-michael@walle.cc
The flag status register is only available on micron flashes. Move all
the functions around that into the micron module.
This is almost a mechanical move except for the spi_nor_fsr_ready()
which now also checks the normal status register. Previously, this was
done in spi_nor_ready().
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-25-michael@walle.cc
XRDSR is a combination of xilinx and the RDSR opcode, but the register
is just the status register. Correct the debug message.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-24-michael@walle.cc
Drop the generic spi_nor prefix for all the xilinx functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-23-michael@walle.cc
Mechanically move all the xilinx functions to its own module.
Then register the new flash specific ready() function.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-22-michael@walle.cc
The _page_size marco parameter was missing parentheses around it. Add
them.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-21-michael@walle.cc
We will move vendor specific code into the vendor modules and thus we
will have to export these functions so they can be called.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-20-michael@walle.cc
Xilinx and Micron flashes have their own implementation of the
spi_nor_ready() function. At the moment, the core will figure out
which one to call according to some flags. Lay the foundation to
make it possible that a flash can register its own ready()
function.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-19-michael@walle.cc
Instead of always using a function pointer (and initializing it to our
default), just call the default function if the flash didn't set its own
one. That will make the call flow easier to follow.
Also mark the parameter as optional now.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-18-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-17-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-16-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-15-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-14-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-13-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-12-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-11-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-10-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-9-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-8-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-7-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-6-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-5-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-4-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-3-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-2-michael@walle.cc
Since nvmem_unregister() checks for NULL, no need to repeat in
the caller. Drop duplicate NULL checks.
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220220151527.17216-13-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wp-gpios property can be used on NVMEM nodes and the same property can
be also used on MTD NAND nodes. In case of the wp-gpios property is
defined at NAND level node, the GPIO management is done at NAND driver
level. Write protect is disabled when the driver is probed or resumed
and is enabled when the driver is released or suspended.
When no partitions are defined in the NAND DT node, then the NAND DT node
will be passed to NVMEM framework. If wp-gpios property is defined in
this node, the GPIO resource is taken twice and the NAND controller
driver fails to probe.
A new Boolean flag named ignore_wp has been added in nvmem_config.
In case ignore_wp is set, it means that the GPIO is handled by the
provider. Lets set this flag in MTD layer to avoid the conflict on
wp_gpios property.
Fixes: 2a127da461 ("nvmem: add support for the write-protect pin")
Cc: stable@vger.kernel.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220220151432.16605-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the support of the WP# signal. WP will be disabled in
probe/resume callbacks and will be enabled in remove/suspend callbacks.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220217144755.270679-3-christophe.kerello@foss.st.com
In devicetree the flash information is embedded within nand chip node,
so during nand chip initialization the nand chip node should be passed
to nand_set_flash_node() api, instead of nand controller node.
Fixes: 08d8c62164 ("mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220209053427.27676-1-amit.kumar-mahapatra@xilinx.com
Buffalo sells some router devices which have trx-formatted firmware,
based on MediaTek MIPS SoCs. To use parser_trx on those devices, add
"RALINK" to dependency and allow to compile for MediaTek MIPS SoCs.
examples:
- WCR-1166DS (MT7628)
- WSR-1166DHP (MT7621)
- WSR-2533DHP (MT7621)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220213064045.1781-1-musashino.open@gmail.com
Platform_driver probe functions aren't called with locks held
and thus don't need GFP_ATOMIC. Use GFP_KERNEL instead.
Problem found with Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220210204223.104181-8-Julia.Lawall@inria.fr
that can be used by SPI controllers to manage SPI NANDs as well as
possibly by parallel NAND controllers. In particular, it brings support
for Macronix ECC engine that can be used with Macronix SPI controller.
The changes touch the NAND core, the NAND ECC core, the spi-mem layer, a
SPI controller driver and add a new NAND ECC driver, as well as a number
of binding updates.
Binding changes:
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmIPpwcACgkQJWrqGEe9
VoRbnwgAgW9tSKGp1B6eA3Xf7Or0SZfmC6H0scV8kfQ2i9OnMOuYMAGs+7whNrcx
Dvb9IfFOMra7umid98EI58YhLsu4IMDtc79Lp04HGY/emjZh47FpAEXZ/vr/45e9
lclUEmjHwUVJ5+XvFwnPLpIWiM0xeL3CN2rAi76uI5sII+Hxt6KkV7L9+N9IjhcA
GsG/8/A16ihbNjVrHoN+ofwmmZkySXvhK7IIg93Tv+VoJCBnn0eEDgtRXvsGoDuq
2xD87MEAhnXw+q9LtSSUwmA/uUCR2RscidGQ+LML0PwKDVUZhzBV8sNrNoPQy374
51XXDCkSF8NRK+FVXIUFTEctdVrE1A==
=UuhB
-----END PGP SIGNATURE-----
Merge tag 'mtd/spi-mem-ecc-for-5.18' into mtd/next
Topic branch bringing-in changes related to the support of ECC engines
that can be used by SPI controllers to manage SPI NANDs as well as
possibly by parallel NAND controllers. In particular, it brings support
for Macronix ECC engine that can be used with Macronix SPI controller.
The changes touch the NAND core, the NAND ECC core, the spi-mem layer, a
SPI controller driver and add a new NAND ECC driver, as well as a number
of binding updates.
Binding changes:
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Merge series from Mika Westerberg <mika.westerberg@linux.intel.com>:
Based on discussion on the patch I sent some time ago here:
http://lists.infradead.org/pipermail/linux-mtd/2021-June/086867.html
it turns out that the preferred way to deal with the SPI flash controller
drivers is through SPI MEM which is part of Linux SPI subsystem.
This series does that for the intel-spi driver. This also renames the
driver to follow the convention used in the SPI subsystem. The first patch
improves the write protection handling to be slightly more safer. The
following two patches do the conversion itself. Note the Intel SPI flash
controller only allows commands such as read, write and so on and it
internally uses whatever addressing etc. it figured from the SFDP on the
flash device.
base-commit: e783362eb5
The preferred way to implement SPI-NOR controller drivers is through SPI
subsubsystem utilizing the SPI MEM core functions. This converts the
Intel SPI flash controller driver over the SPI MEM by moving the driver
from SPI-NOR subsystem to SPI subsystem and in one go make it use the
SPI MEM functions. The driver name will be changed from intel-spi to
spi-intel to match the convention used in the SPI subsystem.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220209122706.42439-3-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver tries to disable the BIOS write protection
automatically even if this is not what the user wants. For this reason
modify the driver so that by default it does not touch the write
protection. Only if specifically asked by the user (setting writeable=1
command line parameter) the driver tries to disable the BIOS write
protection.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220209122706.42439-2-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order for pipelined ECC engines to be able to enable/disable the ECC
engine only when needed and avoid races when future parallel-operations
will be supported, we need to provide the information about the use of
the ECC engine in the direct mapping hooks. As direct mapping
configurations are meant to be static, it is best to create two new
mappings: one for regular 'raw' accesses and one for accesses involving
correction. It is up to the driver to use or not the new ECC enable
boolean contained in the spi-mem operation.
As dirmaps are not free (they consume a few pages of MMIO address space)
and because these extra entries are only meant to be used by pipelined
engines, let's limit their use to this specific type of engine and save
a bit of memory with all the other setups.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-9-miquel.raynal@bootlin.com
As we will soon tweak the dirmap creation to act a little bit
differently depending on the picked ECC engine, we need to initialize
dirmaps after ECC engines. This should not have any effect as dirmaps
are not yet used at this point.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-8-miquel.raynal@bootlin.com
Introduce the support for another possible configuration: the ECC
engine may work as DMA master (pipelined) and move itself the data
to/from the NAND chip into the buffer, applying the necessary
corrections/computations on the fly.
This driver offers an ECC engine implementation that must be
instatiated from a SPI controller driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-17-miquel.raynal@bootlin.com
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In a pipelined engine situation, we might either have the host which
internally has support for error correction, or have it using an
external hardware block for this purpose. In the former case, the host
is also the ECC engine. In the latter case, it is not. In order to get
the right pointers on the right devices (for example: in order to devm_*
allocate variables), let's introduce this helper which can safely be
called by pipelined ECC engines in order to retrieve the right device
structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-16-miquel.raynal@bootlin.com
Some SPI-NAND chips do not support on-die ECC. For these chips,
correction must apply on the SPI controller end. In order to avoid
doing all the calculations by software, Macronix provides a specific
engine that can offload the intensive work.
Add Macronix ECC engine support, this engine can work in conjunction
with a SPI controller and a raw NAND controller, it can be pipelined
or external and supports linear and syndrome layouts.
Right now the simplest configuration is supported: SPI controller
external and linear ECC engine.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-15-miquel.raynal@bootlin.com
Prevent rawnand access while in a suspended state.
Commit 013e6292aa ("mtd: rawnand: Simplify the locking") allows the
rawnand layer to return errors rather than waiting in a blocking wait.
Tested on a iMX6ULL.
Fixes: 013e6292aa ("mtd: rawnand: Simplify the locking")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220208085213.1838273-1-sean@geanix.com
Reduce the number of exported symbols by replacing:
- mtd_expert_analysis_warning (the error string)
- mtd_expert_analysis_mode (the boolean)
with a single helper:
- mtd_check_expert_analysis_mode
Calling this helper will both check/return the content of the internal
boolean -which is not exported anymore- and as well conditionally
WARN_ONCE() the user, like it was done before.
While on this function, make the error string local to the helper and
set it const. Only export this helper when CONFIG_DEBUG_FS is defined to
limit the growth of the Linux kernel size only for a debug feature on
production kernels.
Mechanically update all the consumers.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220128113414.1121924-1-miquel.raynal@bootlin.com
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220202143404.16070-4-broonie@kernel.org
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220202143404.16070-3-broonie@kernel.org
There is no good reason to keep genhd.h separate from the main blkdev.h
header that includes it. So fold the contents of genhd.h into blkdev.h
and remove genhd.h entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220124093913.742411-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On non-OF enabled platforms (CONFIG_OF is not set), of_match_node() will
expand to NULL. The of_device_id array pointed by the macro will then be
left unused. Let's mark the array __maybe_unused in this case to prevent
compiler warnings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20220127110802.1064963-1-miquel.raynal@bootlin.com
of_match_ptr() either expands to NULL if !CONFIG_OF, or is transparent
otherwise. There are several drivers using this macro which keep their
of_device_id array enclosed within an #ifdef CONFIG_OF check, these are
considered fine. However, When misused, the of_device_id array pointed
by this macro will produce a warning because it is finally unused when
compiled without OF support.
A number of fixes are possible:
- Always depend on CONFIG_OF, but this will not always work and may
break boards.
- Enclose the compatible array by #ifdef's, this may save a bit of
memory but will reduce build coverage.
- Tell the compiler the array may be unused, if this can be avoided,
let's not do this.
- Just drop the macro, setting the of_device_id array for a non OF
enabled platform is not an issue, it will just be unused.
The latter solution seems the more appropriate, so let's use it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/linux-mtd/20220127110631.1064705-1-miquel.raynal@bootlin.com
The brcmnand driver contains a bug in which if a page (example 2k byte)
is read from the parallel/ONFI NAND and within that page a subpage (512
byte) has correctable errors which is followed by a subpage with
uncorrectable errors, the page read will return the wrong status of
correctable (as opposed to the actual status of uncorrectable.)
The bug is in function brcmnand_read_by_pio where there is a check for
uncorrectable bits which will be preempted if a previous status for
correctable bits is detected.
The fix is to stop checking for bad bits only if we already have a bad
bits status.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: david regan <dregan@mail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/trinity-478e0c09-9134-40e8-8f8c-31c371225eda-1643237024774@3c-app-mailcom-lxa02
With some spi devices, the heavy cpu usage due to polling the spi
registers may lead to netdev timeouts, RCU complaints, etc. This can
be acute in the absence of CONFIG_PREEMPT. This patch allows to give
enough breathing room to avoid those incorrectly detected netdev
timeouts for example.
Example splat on 5.10.92:
[ 828.399306] rcu: INFO: rcu_sched self-detected stall on CPU
...
[ 828.419245] Task dump for CPU 1:
[ 828.422465] task:kworker/1:1H state:R running task on cpu 1 stack: 0 pid: 76 ppid: 2 flags:0x0000002a
[ 828.433132] Workqueue: kblockd blk_mq_run_work_fn
[ 828.437820] Call trace:
...
[ 828.512267] spi_mem_exec_op+0x4d0/0xde0
[ 828.516184] spi_mem_dirmap_read+0x180/0x39c
[ 828.520443] spi_nor_read_data+0x428/0x7e8
[ 828.524523] spi_nor_read+0x154/0x214
[ 828.528172] mtd_read_oob+0x440/0x714
[ 828.531815] mtd_read+0xac/0x120
[ 828.535030] mtdblock_readsect+0x178/0x230
[ 828.539102] mtd_blktrans_work+0x9fc/0xf28
[ 828.543177] mtd_queue_rq+0x1ac/0x2e4
[ 828.546827] blk_mq_dispatch_rq_list+0x2cc/0xa44
[ 828.551419] blk_mq_do_dispatch_sched+0xb0/0x7cc
[ 828.556010] __blk_mq_sched_dispatch_requests+0x350/0x494
[ 828.561372] blk_mq_sched_dispatch_requests+0xac/0xe4
[ 828.566387] __blk_mq_run_hw_queue+0x130/0x254
[ 828.570806] blk_mq_run_work_fn+0x50/0x60
[ 828.574814] process_one_work+0x578/0xf1c
[ 828.578814] worker_thread+0x5dc/0xea0
[ 828.582547] kthread+0x270/0x2d4
[ 828.585765] ret_from_fork+0x10/0x30
Signed-off-by: David Decotigny <ddecotig@google.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220126101120.676021-1-decot+git@google.com
The problem is that "erasesize" is a uint64_t type so it might be
non-zero but the lower 32 bits are zero so when it's truncated,
"(uint32_t)erasesize", then that value is zero. This leads to a
divide by zero bug.
Avoid the bug by delaying the divide until after we have validated
that "erasesize" is non-zero and within the uint32_t range.
Fixes: dc2b3e5cbc ("mtd: phram: use div_u64_rem to stop overwrite len in phram_setup")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220121115505.GI1978@kadam
We need to select MEMORY as well otherwise OMAP_GPMC will not be built.
For simplicity let's select MEMORY and OMAP_GPMC unconditionally as
this driver depends on OMAP_GPMC driver and uses symbols from there.
Fixes: dbcb124ace ("mtd: rawnand: omap2: Select GPMC device driver for ARCH_K3")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118123525.8020-1-rogerq@kernel.org
Mtdpart doesn't free pparts when a cleanup function is declared.
Add missing free for pparts in cleanup function for smem to fix the
leak.
Fixes: 10f3b4d799 ("mtd: parsers: qcom: Fix leaking of partition name")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220116032211.9728-2-ansuelsmth@gmail.com
In the event of a skipped partition (case when the entry name is empty)
the kernel panics in the cleanup function as the name entry is NULL.
Rework the parser logic by first checking the real partition number and
then allocate the space and set the data for the valid partitions.
The logic was also fundamentally wrong as with a skipped partition, the
parts number returned was incorrect by not decreasing it for the skipped
partitions.
Fixes: 803eb124e1 ("mtd: parsers: Add Qcom SMEM parser")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220116032211.9728-1-ansuelsmth@gmail.com
Its possible for the main smem driver to not be loaded by the time we come
along to parse the smem partition description but, this is a perfectly
normal thing.
No need to print out an error message in this case.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220103030316.58301-3-bryan.odonoghue@linaro.org
Interacting with a NAND chip on an IPQ6018 I found that the qcomsmem NAND
partition parser was returning -EPROBE_DEFER waiting for the main smem
driver to load.
This caused the board to reset. Playing about with the probe() function
shows that the problem lies in the core clock being switched off before the
nandc_unalloc() routine has completed.
If we look at how qcom_nandc_remove() tears down allocated resources we see
the expected order is
qcom_nandc_unalloc(nandc);
clk_disable_unprepare(nandc->aon_clk);
clk_disable_unprepare(nandc->core_clk);
dma_unmap_resource(&pdev->dev, nandc->base_dma, resource_size(res),
DMA_BIDIRECTIONAL, 0);
Tweaking probe() to both bring up and tear-down in that order removes the
reset if we end up deferring elsewhere.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220103030316.58301-2-bryan.odonoghue@linaro.org
If of_find_device_by_node() succeeds, ingenic_ecc_get() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling.
Fixes: 15de8c6efd ("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211230072751.21622-1-linmq006@gmail.com
The variable 'errors' is being used to sum the number of errors
but it is never used afterwards. This can be considered a
redundant set of operations and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211221181340.524639-1-colin.i.king@gmail.com
In the i.MX28 manual (MCIMX28RM, Rev. 1, 2010) you can find an example
(15.2.4 High-Speed NAND Timing) of how to configure the GPMI controller
to manage High-Speed NAND devices, so it was wrong to assume that only
i.MX6 can achieve EDO timings.
This patch has been tested on a 2048/64 byte NAND (Micron MT29F2G08ABAEAH4).
Kernel mtd tests:
- mtd_nandbiterrs
- mtd_nandecctest
- mtd_oobtest
- mtd_pagetest
- mtd_readtest
- mtd_speedtest
- mtd_stresstest
- mtd_subpagetest
- mtd_torturetest [cycles_count = 10000000]
run without errors.
Before this patch (mode 0):
---------------------------
eraseblock write speed is 2098 KiB/s
eraseblock read speed is 2680 KiB/s
page write speed is 1689 KiB/s
page read speed is 2522 KiB/s
2 page write speed is 1899 KiB/s
2 page read speed is 2579 KiB/s
erase speed is 128000 KiB/s
2x multi-block erase speed is 73142 KiB/s
4x multi-block erase speed is 204800 KiB/s
8x multi-block erase speed is 256000 KiB/s
16x multi-block erase speed is 256000 KiB/s
32x multi-block erase speed is 256000 KiB/s
64x multi-block erase speed is 256000 KiB/s
After this patch (mode 5):
-------------------------
eraseblock write speed is 3390 KiB/s
eraseblock read speed is 5688 KiB/s
page write speed is 2680 KiB/s
page read speed is 4876 KiB/s
2 page write speed is 2909 KiB/s
2 page read speed is 5224 KiB/s
erase speed is 170666 KiB/s
2x multi-block erase speed is 204800 KiB/s
4x multi-block erase speed is 256000 KiB/s
8x multi-block erase speed is 256000 KiB/s
16x multi-block erase speed is 256000 KiB/s
32x multi-block erase speed is 256000 KiB/s
64x multi-block erase speed is 256000 KiB/s
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-5-dario.binacchi@amarulasolutions.com
What to do when the real rate of the gpmi clock is not equal to the
required one? The solutions proposed in [1] did not lead to a conclusion
on how to validate the clock rate, so, inspired by the document [2], I
consider the rate correct only if not lower or equal to the rate of the
previous edo mode. In fact, in chapter 4.16.2 (NV-DDR) of the document [2],
it is written that "If the host selects timing mode n, then its clock
period shall be faster than the clock period of timing mode n-1 and
slower than or equal to the clock period of timing mode n.". I thought
that it could therefore also be used in this case, without therefore
having to define the valid rate ranges empirically.
For example, suppose that gpmi_nfc_compute_timings() is called to set
edo mode 5 (100MHz) but the rate returned by clk_round_rate() is 80MHz
(edo mode 4). In this case gpmi_nfc_compute_timings() will return error,
and will be called again to set edo mode 4, which this time will be
successful.
[1] https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org
[2] http://www.onfi.org/-/media/client/onfi/specs/onfi_3_0_gold.pdf?la=en
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-4-dario.binacchi@amarulasolutions.com
Set the controller registers according to the real clock rate. The
controller registers configuration (setup, hold, timeout, ... cycles)
depends on the clock rate of the GPMI. Using the real rate instead of
the ideal one, avoids that this inaccuracy (required_rate - real_rate)
affects the registers setting.
This patch has been tested on two custom boards with i.MX28 and i.MX6
SOCs:
- i.MX28:
required rate 100MHz, real rate 99.3MHz
- i.MX6
required rate 100MHz, real rate 99MHz
Fixes: b120612206 ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-3-dario.binacchi@amarulasolutions.com
The aspeed-smc can have multiple SPI devices attached to it in the
device tree. If one of the devices is missing or failing the entire
probe will fail and all MTD devices under the controller will be
removed. On OpenBMC this results in a kernel panic due to missing
rootfs:
[ 0.538774] aspeed-smc 1e620000.spi: Using 50 MHz SPI frequency
[ 0.540471] aspeed-smc 1e620000.spi: w25q01jv-iq (131072 Kbytes)
[ 0.540750] aspeed-smc 1e620000.spi: CE0 window [ 0x20000000 - 0x28000000 ] 128MB
[ 0.540943] aspeed-smc 1e620000.spi: CE1 window [ 0x28000000 - 0x2c000000 ] 64MB
[ 0.541143] aspeed-smc 1e620000.spi: read control register: 203b0041
[ 0.581442] 5 fixed-partitions partitions found on MTD device bmc
[ 0.581625] Creating 5 MTD partitions on "bmc":
[ 0.581854] 0x000000000000-0x0000000e0000 : "u-boot"
[ 0.584472] 0x0000000e0000-0x000000100000 : "u-boot-env"
[ 0.586468] 0x000000100000-0x000000a00000 : "kernel"
[ 0.588465] 0x000000a00000-0x000006000000 : "rofs"
[ 0.590552] 0x000006000000-0x000008000000 : "rwfs"
[ 0.592605] aspeed-smc 1e620000.spi: Using 50 MHz SPI frequency
[ 0.592801] aspeed-smc 1e620000.spi: unrecognized JEDEC id bytes: 00 00 00 00 00 00
[ 0.593039] Deleting MTD partitions on "bmc":
[ 0.593175] Deleting u-boot MTD partition
[ 0.637929] Deleting u-boot-env MTD partition
[ 0.829527] Deleting kernel MTD partition
[ 0.856902] Freeing initrd memory: 1032K
[ 0.866428] Deleting rofs MTD partition
[ 0.906264] Deleting rwfs MTD partition
[ 0.986628] aspeed-smc 1e620000.spi: Aspeed SMC probe failed -2
[ 0.986929] aspeed-smc: probe of 1e620000.spi failed with error -2
...
[ 2.936719] /dev/mtdblock: Can't open blockdev
mount: mounting /dev/mtdblock on run/initramfs/ro failed: No such file or directory
[ 2.963030] MTD: Couldn't look up '/dev/mtdblock': -2
mount: mounting /dev/mtdblock on run/initramfs/rw failed: No such file or directory
Mounting read-write /dev/mtdblock filesystem failed. Please fix and run
mount /dev/mtdblock run/initramfs/rw -t jffs2 -o rw
or perform a factory reset with the clean-rwfs-filesystem option.
Fatal error, triggering kernel panic!
[ 3.013047] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100
Many BMC designs have two flash chips so that they can handle a hardware
failure of one of them. If one chip failed, it doesn't do any good to
have redundancy if they all get removed anyhow.
Improve the resilience of the probe function to handle one of the
children being missing or failed. Only in the case where all children
fail to probe should the controller be failed out.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211229143334.297305-1-patrick@stwcx.xyz
Add a BCMA shim to allow us to register the brcmnand driver using the
BCMA bus which provides indirect memory mapped access to SoC registers.
There are a number of registers that need to be byte swapped because
they are natively big endian, coming directly from the NAND chip, and
there is no bus interface unlike the iProc or STB platforms that
performs the byte swapping for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-10-f.fainelli@gmail.com
For some odd and unexplained reason the BCMA NAND controller, albeit
revision 3.4 uses a command shift of 0 instead of 24 as it should be,
quirk that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-9-f.fainelli@gmail.com
Make use of the recently refactored code in brcmnand_init_cs() and
derive the chip-select from the platform data that is supplied. Update
the various code paths to avoid relying on possibly non-existent
resources, too.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-8-f.fainelli@gmail.com
The BCMA devices include the brcmnand controller but they do not wire up
any interrupt line, allow the main interrupt to be optional and update
the completion path to also check for the lack of an interrupt line.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-6-f.fainelli@gmail.com
In order to initialize a given chip select object for use by the
brcmnand driver, move all of the Device Tree specific routines outside
of brcmnand_init_cs() in order to make it usable in a platform data
configuration which will be necessary for supporting BCMA chips.
No functional changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-5-f.fainelli@gmail.com
In preparation for encapsulating more of what the loop calling
brcmnand_init_cs() does, avoid using platform_device when it is the
device behind platform_device that we are using for printing errors.
No functional changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-4-f.fainelli@gmail.com
Allow a brcmnand_soc instance to provide a custom set of I/O operations
which we will require when using this driver on a BCMA bus which is not
directly memory mapped I/O. Update the nand_{read,write}_reg accordingly
to use the SoC operations if provided.
To minimize the penalty on other SoCs which do support standard MMIO
accesses, we use a static key which is disabled by default and gets
enabled if a soc implementation does provide I/O operations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-3-f.fainelli@gmail.com
In order to key off the brcmnand_probe() code in subsequent changes
depending upon ctrl->soc, assign that variable as early as possible,
instead of much later when we have checked that it is non-NULL.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-2-f.fainelli@gmail.com
of_get_nand_bus_width() had a wrong behavior because:
1/ it ignored the -ENODATA and -EOVERFLOW return values of
of_property_read_u32(). "nand-bus-width" without value was tolerated
while it shouldn't have been according to the devicetree bindings.
2/ returned -EIO when the nand-bus-width was neither 8 nor 16, when it
should have returned -EINVAL instead.
3/ returned the 8 or 16 bus-width integer, but it was never used it its
caller. A simply return 0 on success is enough.
Rework of_get_nand_bus_width() and address all the above. The execution
is now stopped in case of errors.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220106131610.225661-2-tudor.ambarus@microchip.com
Remove the wrapper as it hides for no reason what we really want: find an
of_property. Removing the wrapper makes the code easier to read.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220106131610.225661-1-tudor.ambarus@microchip.com
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq() effectively
convert that into -EINVAL, even at probe time rather than later on.
So it might be better to check just now.
Fixes: 2c22120fbd ("MTD: OneNAND: interrupt based wait support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220104162658.1988142-1-jiasheng@iscas.ac.cn
The (ns->regs.column + ns->regs.off) pattern repeats a lot which
represents the byte shift in next page to access. We can replace it
with a macro to improve the readability.
Signed-off-by: RinHizakura <s921975628@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211225100713.119089-1-s921975628@gmail.com
The moving block of codes is shared between both 'if' and 'else' condition,
we can move it out to reduce the duplication.
Signed-off-by: RinHizakura <s921975628@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211225100648.119011-1-s921975628@gmail.com
Instead of self-checking overflow and allocating an array of specific size
by counting the total required space handy, we already have existed kernel
API which responses for all these works.
Signed-off-by: RinHizakura <s921975628@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211225100607.118932-1-s921975628@gmail.com
Add the necessary helpers to register/unregister hardware ECC engines
that will be called from ECC engine drivers.
Also add helpers to get the right engine from the user
perspective. Keep a reference of the in use ECC engine in order to
prevent modules to be unloaded. Put the reference when the engine gets
retired.
A static list of hardware (only) ECC engines is setup to keep track of
the registered engines.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-13-miquel.raynal@bootlin.com
Macronix SPI-NAND chips might benefit from an external ECC
engine. Such an engine might need to access random columns, thus needing
to use random commands (0x84 instead of 0x02).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-12-miquel.raynal@bootlin.com
- added MIPS support for brcmstb PCIe controller
- added Loongson 2K1000 reset driver
- removed board support for rbtx4938/rbtx4939
- removed support for TX4939 SoCs
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=wsIG
-----END PGP SIGNATURE-----
Merge tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- add support for more BCM47XX based devices
- add MIPS support for brcmstb PCIe controller
- add Loongson 2K1000 reset driver
- remove board support for rbtx4938/rbtx4939
- remove support for TX4939 SoCs
- fixes and cleanups
* tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (59 commits)
MIPS: ath79: drop _machine_restart again
PCI: brcmstb: Augment driver for MIPs SOCs
MIPS: bmips: Remove obsolete DMA mapping support
MIPS: bmips: Add support PCIe controller device nodes
dt-bindings: PCI: Add compatible string for Brcmstb 74[23]5 MIPs SOCs
MIPS: compressed: Fix build with ZSTD compression
MIPS: BCM47XX: Add support for Netgear WN2500RP v1 & v2
MIPS: BCM47XX: Add support for Netgear R6300 v1
MIPS: BCM47XX: Add LEDs and buttons for Asus RTN-10U
MIPS: BCM47XX: Add board entry for Linksys WRT320N v1
MIPS: BCM47XX: Define Linksys WRT310N V2 buttons
MIPS: Remove duplicated include in local.h
MIPS: retire "asm/llsc.h"
MIPS: rework local_t operation on MIPS64
MIPS: fix local_{add,sub}_return on MIPS64
mips/pci: remove redundant ret variable
MIPS: Loongson64: Add missing of_node_put() in ls2k_reset_init()
MIPS: new Kconfig option ZBOOT_LOAD_ADDRESS
MIPS: enable both vmlinux.gz.itb and vmlinuz for generic
MIPS: signal: Return immediately if call fails
...
It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
* ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
* ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
* HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
* Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1.
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmHgHvgOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE9/JBAAk1qY+2GE7a2j/dRW31rv2JxS3iMnCIdnp/Hn
c0mArt8iEDPXbgmQ2b+tnuqh5GSz073UPCorxkEdAkYisbGSzk22VnfWsNwbSEgC
p8Tqt8ma1blQWUYGzszQEN9u9BCLaMr1cO/ORZmD/f7hSq5W42Q8IYLTb1/9gdax
+pJyBg8Y52PAKURnKWzmDoasJeDoQauxZ9R0g3BgQHj8Hb3QHQonyqKxJlyFac/e
RyV7YycM2ES3Dj4u7TReRd9hdKeuzc2Wg8qYVC3x/9dzhKpvDM3Tg5ONw/58jW4x
G6tuEj5SeEKH2LRQYTOLYScz9lVUalv97PCsq5LkQrDLqrO3hT+vxQpRdBZefRIQ
+cKBd9GReRlQW9XCDrUs9ZuWtl1cyta8T3mk3WhTvjUcTlr1vd+TcyRoQvNhFNVH
LaTjD1526Yra8BxyzSe7tyHhvOIvRWwjzSfwCyYV9097wV82+rOReqHyMDhN7Djc
NbBQvoIh7v1Yo+hOYE3RUUhS5h+CJH8l43J1pWNODjXVYivYTzCOizDdJ8ktRaHE
gpQ1vAM4pW1R5mQsyIwj6G9B1bclYboVBjlE9SXCpT3vmDneIWuLUmNV89gyNW+p
96B3dL4BoCTyBtGYBtow2Es+/rX2dEWtM6pvOSHhRDoWL586Snr2lXDEbAQ9uZF9
zpq1uqs=
=csTR
-----END PGP SIGNATURE-----
Merge tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1"
* tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: hda: intel-dsp-config: reorder the config table
ALSA: hda: intel-dsp-config: add JasperLake support
ALSA: hda: cs35l41: fix double free on error in probe()
ALSA: hda: Fix dependencies of CS35L41 on SPI/I2C buses
ALSA: hda: Fix dependency on ASoC cs35l41 codec
ASoC: cs35l41: Add support for hibernate memory retention mode
ASoC: cs35l41: Update handling of test key registers
ALSA: intel_hdmi: Check for error num after setting mask
ASoC: wcd9335: Keep a RX port value for each SLIM RX mux
ASoC: amd: acp: acp-mach: Change default RT1019 amp dev id
ALSA: virmidi: Remove duplicated code
ALSA: seq: virmidi: Add a drain operation
ASoC: topology: Fix typo
ASoC: fsl_asrc: refine the check of available clock divider
ASoC: Intel: bytcr_rt5640: Add support for external GPIO jack-detect
ASoC: Intel: bytcr_rt5640: Support retrieving the codec IRQ from the AMCR0F28 ACPI dev
ASoC: rt5640: Add support for boards with an external jack-detect GPIO
ASoC: rt5640: Allow snd_soc_component_set_jack() to override the codec IRQ
ASoC: rt5640: Change jack_work to a delayed_work
ASoC: rt5640: Fix possible NULL pointer deref on resume
...
JFFS2:
- Fix for a deadlock in jffs2_write_begin()
UBI:
- Fixes in comments
UBIFS:
- Expose error counters in sysfs
- Many bugfixes found by Hulk Robot and others
-----BEGIN PGP SIGNATURE-----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=rpfR
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Fix for a deadlock in jffs2_write_begin()
UBI:
- Fixes in comments
UBIFS:
- Expose error counters in sysfs
- Many bugfixes found by Hulk Robot and others"
* tag 'for-linus-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: GC deadlock reading a page that is used in jffs2_write_begin()
ubifs: read-only if LEB may always be taken in ubifs_garbage_collect
ubifs: fix double return leb in ubifs_garbage_collect
ubifs: fix slab-out-of-bounds in ubifs_change_lp
ubifs: fix snprintf() length check
ubifs: Document sysfs nodes
ubifs: Export filesystem error counters
ubifs: Error path in ubifs_remount_rw() seems to wrongly free write buffers
ubifs: Make use of the helper macro kthread_run()
ubi: Fix a mistake in comment
ubifs: Fix spelling mistakes
* mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
* gen_probe: Use bitmap_zalloc() when applicable
* Introduce an expert mode for forensics and debugging purposes
* Clear out unregistered devices a bit more
* Provide unique name for nvmem device
* Remove unused header file <linux/mtd/latch-addr-flash.h>
* Fixed breaking list in __mtd_del_partition.
MTD device changes:
* sst25l, mchp48l640, mchp23k256, dataflash:
- Warn about failure to unregister mtd device
Raw NAND core changes:
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
* Add Pratyush as SPI NOR co-maintainer.
* Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
* Rework the flash_info flags and clarify where one should be used.
* Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
* Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
* Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
* Fix mtd size for s3an flashes.
* Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
Hyperbus changes:
* Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmHO+g8ACgkQJWrqGEe9
VoRW1AgAjFC58ARNBw7asYerGyiUWv7b8RjPIRWZqmcSQ6D5m20cGNBTa15c2NrC
v0dNMf2+3FrCECso6wKPbkEbLt9lHjlMmt+AdlraV0QvHBXrJq/Tc2p2ATI5kTqq
WaP4oCx1mccgO+IrEIiGikOcFx/TLBBJEk+U0Anbm16eia9Cjw+uD/q7X2HbF5xQ
MOFZyQ+rAVqkM8tCh6VHhCpX85pn9pj2ZdouOhPWsqjULaGqDbUopC70YPZLVJyx
9u4xHFaVLVae6AS5Gitser2ie8klypTN/H+1weSao43GGmwIrT0wK0mCOVIm90Zd
4frlpnt4QE/IIAKgAm+HxkWg+KV9qg==
=E8lV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core changes:
- mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
- gen_probe: Use bitmap_zalloc() when applicable
- Introduce an expert mode for forensics and debugging purposes
- Clear out unregistered devices a bit more
- Provide unique name for nvmem device
- Remove unused header file <linux/mtd/latch-addr-flash.h>
- Fixed breaking list in __mtd_del_partition.
MTD device changes:
- Warn about failure to unregister mtd device in sst25l, mchp48l640,
mchp23k256, and dataflash drivers.
Raw NAND core changes:
- Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
- OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
- Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
- Onenand:
- Remove redundant variable ooblen
- MPC5121:
- Remove unused variable in ads5121_select_chip()
- GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
- Ingenic:
- JZ4740 needs 'oob_first' read page function
- Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where
possible. Flash parameters and settings that are SFDP discoverable
should not be duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP
standard, or the SFDP tables which define those flash parameters
are not defined by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long
transactions are not allowed in 8D-8D-8D mode.
Hyperbus changes:
- Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe"
* tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (71 commits)
mtd: spi-nor: Remove debugfs entries that duplicate sysfs entries
mtd: spi-nor: micron-st: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: spansion: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: core: use 2 data bytes for template ops
mtd: spi-nor: Constify part specific fixup hooks
mtd: spi-nor: core: Remove reference to spi-nor.c
mtd: rawnand: gpmi: Use platform_get_irq_byname() to get the interrupt
mtd: rawnand: omap_elm: Use platform_get_irq() to get the interrupt
mtd: rawnand: omap2: Select GPMC device driver for ARCH_K3
memory: omap-gpmc: Use a compatible match table when checking for NAND controller
memory: omap-gpmc: Add support for GPMC on AM64 SoC
dt-bindings: memory-controllers: ti,gpmc: Add compatible for AM64
memory: omap-gpmc: Use platform_get_irq() to get the interrupt
MAINTAINERS: Add an entry for Renesas NAND controller
mtd: rawnand: renesas: Add new NAND controller driver
dt-bindings: mtd: renesas: Describe Renesas R-Car Gen3 & RZ/N1 NAND controller
mtd: rawnand: gpmi: remove unneeded variable
mtd: rawnand: omap2: drop unused variable
mtd: rawnand: omap2: fix force_8bit flag behaviour for DMA mode
mtd: rawnand: omap2: Add compatible for AM64 SoC
...
Abort fastmap scanning and return error code if memory allocation fails
in add_aeb(). Otherwise ubi will get wrong peb statistics information
after scanning.
Fixes: dbb7d2a88d ("UBI: Add fastmap core")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU,
as well as a new USIv2 driver that handles various types of
serial communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple
drivers, as well as memory controller support for RZ/G2L
(R9A07G044).
- Apple M1 gains support for the PMGR power management driver
-----BEGIN PGP SIGNATURE-----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=tlZT
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU, as
well as a new USIv2 driver that handles various types of serial
communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple drivers,
as well as memory controller support for RZ/G2L (R9A07G044).
- Apple M1 gains support for the PMGR power management driver"
* tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
Hulk Robot reported a KASAN report about use-after-free:
==================================================================
BUG: KASAN: use-after-free in __list_del_entry_valid+0x13d/0x160
Read of size 8 at addr ffff888035e37d98 by task ubiattach/1385
[...]
Call Trace:
klist_dec_and_del+0xa7/0x4a0
klist_put+0xc7/0x1a0
device_del+0x4d4/0xed0
cdev_device_del+0x1a/0x80
ubi_attach_mtd_dev+0x2951/0x34b0 [ubi]
ctrl_cdev_ioctl+0x286/0x2f0 [ubi]
Allocated by task 1414:
device_add+0x60a/0x18b0
cdev_device_add+0x103/0x170
ubi_create_volume+0x1118/0x1a10 [ubi]
ubi_cdev_ioctl+0xb7f/0x1ba0 [ubi]
Freed by task 1385:
cdev_device_del+0x1a/0x80
ubi_remove_volume+0x438/0x6c0 [ubi]
ubi_cdev_ioctl+0xbf4/0x1ba0 [ubi]
[...]
==================================================================
The lock held by ctrl_cdev_ioctl is ubi_devices_mutex, but the lock held
by ubi_cdev_ioctl is ubi->device_mutex. Therefore, the two locks can be
concurrent.
ctrl_cdev_ioctl contains two operations: ubi_attach and ubi_detach.
ubi_detach is bug-free because it uses reference counting to prevent
concurrency. However, uif_init and uif_close in ubi_attach may race with
ubi_cdev_ioctl.
uif_init will race with ubi_cdev_ioctl as in the following stack.
cpu1 cpu2 cpu3
_______________________|________________________|______________________
ctrl_cdev_ioctl
ubi_attach_mtd_dev
uif_init
ubi_cdev_ioctl
ubi_create_volume
cdev_device_add
ubi_add_volume
// sysfs exist
kill_volumes
ubi_cdev_ioctl
ubi_remove_volume
cdev_device_del
// first free
ubi_free_volume
cdev_del
// double free
cdev_device_del
And uif_close will race with ubi_cdev_ioctl as in the following stack.
cpu1 cpu2 cpu3
_______________________|________________________|______________________
ctrl_cdev_ioctl
ubi_attach_mtd_dev
uif_init
ubi_cdev_ioctl
ubi_create_volume
cdev_device_add
ubi_debugfs_init_dev
//error goto out_uif;
uif_close
kill_volumes
ubi_cdev_ioctl
ubi_remove_volume
cdev_device_del
// first free
ubi_free_volume
// double free
The cause of this problem is that commit 714fb87e8b make device
"available" before it becomes accessible via sysfs. Therefore, we
roll back the modification. We will fix the race condition between
ubi device creation and udev by removing ubi_get_device in
vol_attribute_show and dev_attribute_show.This avoids accessing
uninitialized ubi_devices[ubi_num].
ubi_get_device is used to prevent devices from being deleted during
sysfs execution. However, now kernfs ensures that devices will not
be deleted before all reference counting are released.
The key process is shown in the following stack.
device_del
device_remove_attrs
device_remove_groups
sysfs_remove_groups
sysfs_remove_group
remove_files
kernfs_remove_by_name
kernfs_remove_by_name_ns
__kernfs_remove
kernfs_drain
Fixes: 714fb87e8b ("ubi: Fix race condition between ubi device creation and udev")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
After removal of RBTX4939 board support remove code for the TX4939 SoC.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
No active MIPS user own this board, so let's remove it.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller drivers:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmHO9D0ACgkQJWrqGEe9
VoRglwf/SsGcY+7vlBM1VSbUMIF/j5/xuigHIW6AxiN/hu672GMVi7nP7aHg4t3m
DpO5X6ngYFHyW79uksRfwSun/JF1mOqF4De9zhs+cy8hlV12tgEmUNB3cbv4kuFQ
e/N8/mlNrNJ2oQ1C3G3HWe3sngh2vrkhuG49t7M2TJaGAo7V4RW3z9+glNpWMb7m
YIj6gXPjPx7vuEWv80GBUcWNKBzNdRVkrQnj3C2I/ZCslnwYWBLBQxX/U9/KDkPH
7i7MgeknAlV0G/W4TfnNSAKiWOcmWdbmuJ/lOWv4+skdXoMb0/rlC6kvJqOLvbF6
2nUrc9yFTwkNfVTGJm5eWJ0yDUHMgA==
=DQck
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.17' into mtd/next
Raw NAND core:
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller drivers:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer drivers changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmHMJxcACgkQS1VPR6WN
FOk1Ywf9GrDTrGx8Brg08qC7m2ExIiyRBFnUL4yeD9/d8p0vqqGryXeyjbaVutHR
fKf/SFrrP+gmcJS7wx4EttafgV8MPMiV1ICu/vyq2JsOlKekSEk38BXpfNOXzsgQ
UPE92AW8+BTgoL5XohnHqHrFqs+FEHAa3jCEpntWoShznZMhZ6IDwZbVlrHJC5Ts
C0S0S45X5aFgOXdNC4B0UrxAu0OryxL+vjjzG3Jl1g8GbrC/vkbR5vkMXaVgZiie
RpZtsbkcYm9vhUxOgMY+rRi4mwiTxy5Z2/Vg4Jr8nQOurO/aIvC9IZVIS4zbFOTk
08WtqtexR5S/+GCGIijJ+0BlS58hgg==
=tiIB
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.17' into mtd/next
SPI NOR core changes:
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer drivers changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Hyperbus changes:
Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAmHFzxgQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW462AB/93JmhhKIPM6F0gwlm5fCUT6Q0HRUeXeGRS
42z21CbxG7dlf8/VUbNpNJjrMv1wYBVUlyIDZejIdLmXQVK3cdrbHv5lls96uDq6
0tmCemctHfUjbMfINy7cwTMmOkLkimtV59pilP2eXDq63O2AIUc1guGiSwbiCQ9u
yl0/tOVu2BTpahiMk+Us6ljFMhAdS7vSGpW8QbmNt9Z0Dh8B9qr3iahQswHP/cEa
Y1NxZz84QZRWb1TZ6x9LHEsqNf3SFM6NIaA+qUnS8fguQaEMBzrkabsgSZ7eHKY5
8ffqEQ8XVpNxqNBiBx3tjVIZmYJLOPsW95QV4VjzU/jjSd++f24M
=tzl8
-----END PGP SIGNATURE-----
Merge tag 'cfi/for-5.17' into mtd/next
Hyperbus changes for v5.17-rc1
Hyperbus changes:
Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
1. Add support for AM64 SoC.
2. Minor improvement: use platform_get_irq().
-----BEGIN PGP SIGNATURE-----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=eb46
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-omap-5.17' into nand/next
Memory controller drivers for v5.17 - OMAP GPMC
1. Add support for AM64 SoC.
2. Minor improvement: use platform_get_irq().
[miquel.raynal@bootlin.com: A first commit introduced a new omap
compatible and another moved the IDs to a header which created a
conflict: moving the new ID as well in the header fixed it.]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI NOR sysfs defines partname and jedec_id device attributes, which
duplicate the information from debugfs. Since the sysfs directory
structure and the attributes in each directory define an ABI between the
kernel and user space, thus it can never be removed, remove the debugfs
entries so that we don't duplicate the information.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211217122636.474976-2-tudor.ambarus@microchip.com
Fixes: 2a734bb8d5 ("UBI: use debugfs for the extra checks knobs")
There is a mistake in docstrings, it should be ubi_debugfs_exit_dev
instead of dbg_debug_exit_dev.
Signed-off-by: Kai Song <songkai01@inspur.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The Octal DTR configuration is stored in the CFR0V register. This
register is 1 byte wide. But 1 byte long transactions are not allowed in
8D-8D-8D mode. The next byte address contains the CFR1V register, which
contains the number of dummy cycles. This is very fortunate since the
enable path changes the value of this register. Reset the value to its
default when disabling Octal DTR mode. This way, both changes to the
flash state made when enabling can be reverted in one single
transaction.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210531181757.19458-4-p.yadav@ti.com
The Octal DTR configuration is stored in the CFR5V register. This
register is 1 byte wide. But 1 byte long transactions are not allowed in
8D-8D-8D mode. Since the next byte address does not contain any
register, it is safe to write any value to it. Write a 0 to it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210531181757.19458-3-p.yadav@ti.com
The template ops used in spi_nor_spimem_check_pp() and
spi_nor_spimem_check_readop() currently set the data phase to 1 byte
long. This is problematic for 8D-8D-8D protocol where odd length data
phase is invalid since one cycle transfers 2 bytes and odd number of
bytes would mean half a cycle is left over. This could result in a
controller rejecting the op as "not supported" even though it actually
supports the protocol.
Change the data length to 2 bytes in these templates. One might argue
that this should only be done for 8D-8D-8D operations but when talking
about these templates, there is no functional difference between one and
two bytes, even in STR modes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210531181757.19458-2-p.yadav@ti.com
Remove the references to the old spi-nor.c file.
The old drivers/mtd/spi-nor/spi-nor.c file
is not more present and now some of its code is contained in:
drivers/mtd/spi-nor/core.c
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
[tudor.ambarus@microchip.com:
- remove change in Documentation/driver-api/mtd/spi-nor.rst.
The documentation has to be rewritten entirely.
- update commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20210126092516.1431913-1-f.suligoi@asem.it
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211221212609.31290-3-prabhakar.mahadev-lad.rj@bp.renesas.com
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211221212609.31290-2-prabhakar.mahadev-lad.rj@bp.renesas.com
The GPMC device driver is required for NAND controller
to work on K3 Architecture. Select it if required.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211221131757.2030-5-rogerq@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As more compatibles can be added to the GPMC NAND controller driver
use a compatible match table.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211221131757.2030-4-rogerq@kernel.org
[krzysztof: remove "is_nand" variable]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Introduce Renesas NAND controller driver which currently supports the
following features on R-Car Gen3 and RZ/N1 SoCs:
- All ONFI timing modes
- Different configurations of its internal ECC controller
- On-die (not tested) and software ECC support
- Several chips (not tested)
- Subpage accesses
- DMA and PIO
This controller was originally provided by Evatronix before being bought
by Cadence.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/linux-mtd/20211217142033.353599-3-miquel.raynal@bootlin.com
Sascha Hauer