Resolve the sparse warning:
"sparse: Variable length array is used."
Use 2 arrays for 2 PRM register accesses.
Fixes: 96f17e0776 ("mlxsw: spectrum: Support RED qdisc offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After performing reset driver polls on HW indication until learning
that the reset is done, but immediately after reset the device becomes
unresponsive which might lead to completion timeout on the first read.
Wait for 100ms before starting the polling.
Fixes: 233fa44bd6 ("mlxsw: pci: Implement reset done check")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link state and exception interrupts may be masked when we probe.
The firmware should in theory prevent sending (and automasking) those
interrupts if the device is disabled, but if my reading of the FW code
is correct there are firmwares out there with race conditions in this
area. The interrupt may also be masked if previous driver which used
the device was malfunctioning and we didn't load the FW (there is no
other good way to comprehensively reset the PF).
Note that FW unmasks the data interrupts by itself when vNIC is
enabled, such helpful operation is not performed for LSC/EXN interrupts.
Always unmask the auxiliary interrupts after request_irq(). On the
remove path add missing PCI write flush before free_irq().
Fixes: 4c3523623d ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hopefully the last set of fixes for 4.15.
iwlwifi
* fix DMA mapping regression since v4.14
wcn36xx
* fix dynamic power save which has been broken since the driver was commited
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaVLeaAAoJEG4XJFUm622bYBUH/2NhQwUJbKIrbxYhYpo0d++8
GK3TjxpzTByCe0nXGUT5iuDaY72i9C2UoLhFQ5smVg04pE0IXQQjZus6vSGx4biz
GUave/SkzL0EruUXjXLBYWiYDND4iynk82gWX2/Lh7qGoT2SQfD5cKz0cMdE5NrW
E7Q1CMiaoB0i9jcksaU2uWA0XPwISxl61kU2dXuKHQOJ1CW1goI/YIHsBajshHmi
ZEfMqxZFE+jz2Kkp4tKhvG/Xva0ylJv8bwK8CMK6MqA8oa3xdgOhv67E9mm7IGpD
ETrRLJNnWGJlnod5u7QOZWcS01gAgT5whCqDl/lTEty0823kvjMQdwckQaIU+AE=
=me16
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
Hopefully the last set of fixes for 4.15.
iwlwifi
* fix DMA mapping regression since v4.14
wcn36xx
* fix dynamic power save which has been broken since the driver was commited
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
set_fipers() calling should be protected by spinlock in
case that any interrupt breaks related registers setting
and the function we expect. This patch is to move set_fipers()
to spinlock protecting area in ptp_gianfar_adjtime().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TXALCR1 offsets are incorrect in the register offset tables, most
probably due to copy&paste error. Luckily, the driver never uses this
register. :-)
Fixes: 4a55530f38 ("net: sh_eth: modify the definitions of register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.
Fixes: 4bdcb1dd9f ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1463447 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.
The guest would face errors like:
[root@guest ~]# ethtool -i eth0
Cannot get driver information: No such device
[root@guest ~]# ifconfig eth0
eth0: error fetching interface information: Device not found
This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_type in HWRM_FLOW_ALLOC is not being populated correctly due to
incorrect passing of pointer and size of l3_mask argument of is_wildcard().
Fixed this.
Fixes: db1d36a273 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds")
Signed-off-by: Sunil Challa <sunilkumar.challa@broadcom.com>
Reviewed-by: Sathya Perla <sathya.perla@broadcom.com>
Reviewed-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SH7757 has 2 Fast and 2 Gigabit Ether controllers, while the
'sh_eth' driver can only reset and initialize TSU of the first controller
pair. Shimoda-san tried to solve that adding the 'needs_init' member to the
'struct sh_eth_plat_data', however the platform code still never sets this
flag. I think that we can infer this information from the 'devno' variable
(set to 'platform_device::id') and reset/init the Ether controller pair
only for an even 'devno'; therefore 'sh_eth_plat_data::needs_init' can be
removed...
Fixes: 150647fb2c ("net: sh_eth: change the condition of initialization")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlpORQ0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9udAB/9dB0H3bar+wLarrX5bPHuIios9545C
0vgqDJ7pftwpU8WH10NiJfRwLXIEAqvM8ipJtJrRtQV+qdPUHI9ZFRZ63g8nGf3p
Eut697i8jkaHNpdJ+klfww+V1KK5NAy8TqM5TyQOzrSNT4xTMrxFu7igoqvRy0lm
6VxwPeq9GLnbrUIzHQG3ggGqI7lUmOglxPaf3qon00p41ZJhztFOuBEjgGEMyq3w
SOj+K+ciDbsC/k2AIk2XzgOXpfPztLwc4x5UJkmowMOPckV83uw54w2BNHX4Kwex
h2xz9ytu2bHpOvtIDDhLYdJYL43ajr7wQXvIZj6C3dGO7dxDjTbFpkRQ
=AHV0
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.15-20180104' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-01-04
this is a pull request for net/master consisting of 4 patches.
The first patch is by Oliver Hartkopp, it improves the error checking
during the creation of a vxcan link. Wolfgang Grandegger's patch for the
gs_usb driver fixes the return value of the "set_bittiming" callback.
Luu An Phu provides a patch for the flexcan driver to fix the frame
length check in the flexcan_start_xmit() function. The last patch is by
Martin Lederhilger for the ems_usb driver and improves the error
reporting for error warning and passive frames.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes in probe error path:
- Restore dev_id before failed_ioremap path.
Fixes: ("net: fec: restore dev_id in the cases of probe error")
- Call of_node_put(phy_node) before failed_phy path.
Fixes: ("net: fec: Support phys probed from devicetree and fixed-link")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
22000 devices (previously referenced as A000) can support
short transmit queues. This means that we have less DMA
descriptors (TFD) for those shorter queues.
Previous devices must still have 256 TFDs for each queue
even if those 256 TFDs point to fewer buffers.
When I introduced support for the short queues for 22000
I broke older devices by assuming that they can also have
less TFDs in their queues. This led to several problems:
1) the payload of the commands weren't unmapped properly
which caused the SWIOTLB to complain at some point.
2) the hardware could get confused and we get hardware
crashes.
The corresponding bugzilla entries are:
https://bugzilla.kernel.org/show_bug.cgi?id=198201https://bugzilla.kernel.org/show_bug.cgi?id=198265
Cc: stable@vger.kernel.org # 4.14+
Fixes: 4ecab56160 ("iwlwifi: pcie: support short Tx queues for A000 device family")
Reviewed-by: Sharon, Sara <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When switching the driver to the managed device API, I managed to break
the case of a dual Ether devices sharing a single TSU: the 2nd Ether port
wouldn't probe. Iwamatsu-san has tried to fix this but his patch was buggy
and he then dropped the ball...
The solution is to limit calling devm_request_mem_region() to the first
of the two ports sharing the same TSU, so devm_ioremap_resource() can't
be used anymore for the TSU resource...
Fixes: d5e07e6921 ("sh_eth: use managed device API")
Reported-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note in the databook - Section 4.4 - EEE :
" The EEE feature is not supported when the MAC is configured to use the
TBI, RTBI, SMII, RMII or SGMII single PHY interface. Even if the MAC
supports multiple PHY interfaces, you should activate the EEE mode only
when the MAC is operating with GMII, MII, or RGMII interface."
Applying this restriction solves a stability issue observed on Amlogic
gxl platforms operating with RMII interface and the internal PHY.
Fixes: 83bf79b6bb ("stmmac: disable at run-time the EEE if not supported")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since driver does not report hardware dynamic power saving cap,
this is up to the mac80211 to manage power saving timeout and
state machine, using the ieee80211 config callback to report
PS changes. This patch enables/disables PS mode according to
the new configuration.
Remove old behaviour enabling PS mode in a static way, this make
the device unusable when power save is enabled since device is
forced to PS regardless RX/TX traffic.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds the missing CAN_ERR_CRTL to cf->can_id in case of
CAN_STATE_ERROR_WARNING or CAN_STATE_ERROR_PASSIVE
Signed-off-by: Martin Lederhilger <m.lederhilger@ds-automotion.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan_start_xmit() function compares the frame length with data
register length to write frame content into data[0] and data[1]
register. Data register length is 4 bytes and frame maximum length is 8
bytes.
Fix the check that compares frame length with 3. Because the register
length is 4.
Signed-off-by: Luu An Phu <phu.luuan@nxp.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The "set_bittiming" callback treats a positive return value as error!
For that reason "can_changelink()" will quit silently after setting
the bittiming values without processing ctrlmode, restart-ms, etc.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Picking up the patch from Serhey Popovych (commit 191cdb3822,
"veth: Be more robust on network device creation when no attributes").
When the peer name attribute is not provided the former implementation tries
to register the given device name twice ... which leads to -EEXIST.
If only one device name is given apply an automatic generated and valid name
for the peer.
Cc: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Models such as BCM5395/97/98 and BCM53125/24/53115 and compatible require that
we turn on managed mode to actually act on Broadcom tags, otherwise they just
pass them through on ingress (host -> switch) and don't insert them in egress
(switch -> host). Turning on managed mode is simple, but requires us to
properly support ARL misses on multicast addresses which is a much more
involved set of changes not suitable for a bug fix for this release.
Reported-by: Jochen Friedrich <jochen@scram.de>
Fixes: 7edc58d614 ("net: dsa: b53: Turn on Broadcom tags")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-01-03
This series contains fixes for i40e and i40evf.
Amritha removes the UDP support for big buffer cloud filters since it is
not supported and having UDP enabled is a bug.
Alex fixes a bug in the __i40e_chk_linearize() which did not take into
account large (16K or larger) fragments that are split over 2 descriptors,
which could result in a transmit hang.
Jake fixes an issue where a devices own MAC address could be removed from
the unicast address list, so force a check on every address sync to ensure
removal does not happen.
Jiri Pirko fixes the return value when a filter configuration is not
supported, do not return "invalid" but return "not supported" so that
the core can react correctly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A few spots in 3c59x missed calls to dma_mapping_error checks, casuing
WARN_ONS to trigger. Clean those up. While we're at it, refactor the
refill code a bit so that if skb allocation or dma mapping fails, we
recycle the existing buffer. This prevents holes in the rx ring, and
makes for much simpler logic
Note: This is compile only tested. Ted, if you could run this and
confirm that it continues to work properly, I would appreciate it, as I
currently don't have access to this hardware
Signed-off-by: Neil Horman <nhorman@redhat.com>
CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: tedheadster@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
ENA admin command queue errors are not handled as part of ena_down().
As a result, in case of error admin queue transitions to non-running
state and aborts all subsequent commands including those coming from
ena_up(). Reset scheduled by the driver from the timer service
context would not proceed due to sharing rtnl with ena_up()/ena_down()
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain conditions MSI-X interrupt might arrive right after it
was unmasked in ena_up(). There is a chance it would be processed by
the driver before device ENA_FLAG_DEV_UP flag is set. In such a case
the interrupt is ignored.
ENA device operates in auto-masked mode, therefore ignoring
interrupt leaves it masked for good.
Moving unmask of interrupt to be the last step in ena_up().
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 96ac18f14a ("cxgb4: Add support for new flash parts")
removed initialization of adapter->params.sf_fw_start causing issues
while flashing firmware to card. We no longer need sf_fw_start
in adapter->params as we already have macros defined for FW flash
addresses.
Fixes: 96ac18f14a ("cxgb4: Add support for new flash parts")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filter configuration is not supported, drivers should return
-EOPNOTSUPP so the core can react correctly.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, such as with bridging, it is possible that the
stack will add a devices own MAC address to its unicast address list.
If, later, the stack deletes this address, then the i40e driver will
receive a request to remove this address.
The driver stores its current MAC address as part of the MAC/VLAN hash
array, since it is convenient and matches exactly how the hardware
expects to be told which traffic to receive.
This causes a problem, since for more devices, the MAC address is stored
separately, and requests to delete a unicast address should not have the
ability to remove the filter for the MAC address.
Fix this by forcing a check on every address sync to ensure we do not
remove the device address.
There is a very narrow possibility of a race between .set_mac and
.set_rx_mode, if we don't change netdev->dev_addr before updating our
internal MAC list in .set_mac. This might be possible if .set_rx_mode is
going to remove MAC "XYZ" from the list, at the same time as .set_mac
changes our dev_addr to MAC "XYZ", we might possibly queue a delete,
then an add in .set_mac, then queue a delete in .set_rx_mode's
dev_uc_sync and then update netdev->dev_addr. We can avoid this by
moving the copy into dev_addr prior to the changes to the MAC filter
list.
A similar race on the other side does not cause problems, as if we're
changing our MAC form A to B, and we race with .set_rx_mode, it could
queue a delete from A, we'd update our address, and allow the delete.
This seems like a race, but in reality we're about to queue a delete of
A anyways, so it would not cause any issues.
A race in the initialization code is unlikely because the netdevice has
not yet been fully initialized and the stack should not be adding or
removing addresses yet.
Note that we don't (yet) need similar code for the VF driver because it
does not make use of __dev_uc_sync and __dev_mc_sync, but instead roles
its own method for handling updates to the MAC/VLAN list, which already
has code to protect against removal of the hardware address.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original code for __i40e_chk_linearize didn't take into account the
fact that if a fragment is 16K in size or larger it has to be split over 2
descriptors and the smaller of those 2 descriptors will be on the trailing
edge of the transmit. As a result we can get into situations where we didn't
catch requests that could result in a Tx hang.
This patch takes care of that by subtracting the length of all but the
trailing edge of the stale fragment before we test for sum. By doing this
we can guarantee that we have all cases covered, including the case of a
fragment that spans multiple descriptors. We don't need to worry about
checking the inner portions of this since 12K is the maximum aligned DMA
size and that is larger than any MSS will ever be since the MTU limit for
jumbos is something on the order of 9K.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Defer probe if regulator is not ready. E.g. some regulator is fixed
regulator controlled by i2c expander gpio, the i2c device may be probed
after the driver, then it should handle the case of defer probe error.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The static variable dev_id always plus one before netdev registerred.
It should restore the dev_id value in the cases of probe error.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since UDP based filters are not supported via big buffer cloud
filters, remove UDP support. Also change a few return types to
indicate unsupported vs invalid configuration.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-01-02
This series contains fixes for e1000 and e1000e.
Tushar Dave adds a check to the driver so that it won't attempt to disable a
device that is already disabled for e1000.
Benjamin Poirier provides a fix to e1000e, where a previous commit that
Benjamin submitted changed the meaning of the return value for
"check_for_link" for copper media and not all the instances were properly
updated. Benjamin fixes the remaining instances that needed the change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PID 0x9625 of YUGA CLM920-NC5.
YUGA CLM920-NC5 needs to enable QMI_WWAN_QUIRK_DTR before QMI operation.
qmicli -d /dev/cdc-wdm0 -p --dms-get-revision
[/dev/cdc-wdm0] Device revision retrieved:
Revision: 'CLM920_NC5-V1 1 [Oct 23 2016 19:00:00]'
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e_check_for_copper_link() and e1000_check_for_copper_link_ich8lan()
are the two functions that may be assigned to mac.ops.check_for_link when
phy.media_type == e1000_media_type_copper. Commit 19110cfbb3 ("e1000e:
Separate signaling for link check/link up") changed the meaning of the
return value of check_for_link for copper media but only adjusted the first
function. This patch adjusts the second function likewise.
Reported-by: Christian Hesse <list@eworm.de>
Reported-by: Gabriel C <nix.or.die@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198047
Fixes: 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Christian Hesse <list@eworm.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we remove a socket or upstream, and the other side isn't
registered, we dereference a NULL pointer, causing a kernel oops.
Fix this.
Fixes: ce0aa27ff3 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we disable the netdev carrier, we fail to report in the kernel
log that the link went down. Fix this.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the macvlan_uninit would free the macvlan port, so there is one
double free case in macvlan_common_newlink. When the macvlan port is just
created, then register_netdevice or netdev_upper_dev_link failed and they
would invoke macvlan_uninit. Then it would reach the macvlan_port_destroy
which triggers the double free.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 25cc72a338 ("mlxsw: spectrum: Forbid linking to devices that
have uppers") the driver forbids enslavement to netdevs that already
have uppers of their own, as this can result in various ordering
problems.
This requirement proved to be too strict for some users who need to be
able to enslave ports to a bridge that already has uppers. In this case,
we can allow the enslavement if the bridge is already known to us, as
any configuration performed on top of the bridge was already reflected
to the device.
Fixes: 25cc72a338 ("mlxsw: spectrum: Forbid linking to devices that have uppers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we remove the neighbour associated with a nexthop we should always
refuse to write the nexthop to the adjacency table. Regardless if it is
already present in the table or not.
Otherwise, we risk dereferencing the NULL pointer that was set instead
of the neighbour.
Fixes: a7ff87acd9 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a93bf0ff44 ("vxlan: update skb dst pmtu on tx path") has fixed
a performance issue caused by the change of lower dev's mtu for vxlan.
The same thing needs to be done for geneve as well.
Note that geneve cannot adjust it's mtu according to lower dev's mtu
when creating it. The performance is very low later when netperfing
over it without fixing the mtu manually. This patch could also avoid
this issue.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) IPv6 gre tunnels end up with different default features enabled
depending upon whether netlink or ioctls are used to bring them up.
Fix from Alexey Kodanev.
2) Fix read past end of user control message in RDS< from Avinash
Repaka.
3) Missing RCU barrier in mini qdisc code, from Cong Wang.
4) Missing policy put when reusing per-cpu route entries, from Florian
Westphal.
5) Handle nested PCI errors properly in bnx2x driver, from Guilherme G.
Piccoli.
6) Run nested transport mode IPSEC packets via tasklet, from Herbert
Xu.
7) Fix handling poll() for stream sockets in tipc, from Parthasarathy
Bhuvaragan.
8) Fix two stack-out-of-bounds issues in IPSEC, from Steffen Klassert.
9) Another zerocopy ubuf handling fix, from Willem de Bruijn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
strparser: Call sock_owned_by_user_nocheck
sock: Add sock_owned_by_user_nocheck
skbuff: in skb_copy_ubufs unclone before releasing zerocopy
tipc: fix hanging poll() for stream sockets
sctp: Replace use of sockets_allocated with specified macro.
bnx2x: Improve reliability in case of nested PCI errors
tg3: Enable PHY reset in MTU change path for 5720
tg3: Add workaround to restrict 5762 MRRS to 2048
tg3: Update copyright
net: fec: unmap the xmit buffer that are not transferred by DMA
tipc: fix tipc_mon_delete() oops in tipc_enable_bearer() error path
tipc: error path leak fixes in tipc_enable_bearer()
RDS: Check cmsg_len before dereferencing CMSG_DATA
tcp: Avoid preprocessor directives in tracepoint macro args
tipc: fix memory leak of group member when peer node is lost
net: sched: fix possible null pointer deref in tcf_block_put
tipc: base group replicast ack counter on number of actual receivers
net_sched: fix a missing rcu barrier in mini_qdisc_pair_swap()
net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaround
ip6_gre: fix device features for ioctl setup
...
- cxgb4 fix for an iser testing failure as debugged by Steve and Sagi.
The problem was a driver bug in the handling of shutting down a QP.
- Various vmw_pvrdma fixes for bogus WARN_ON, missed resource free on error
unwind and a use after free bug
- Improper congestion counter values on mlx5 when link aggregation is enabled
- ipoib lockdep regression introduced in this merge window
- hfi1 regression supporting the device in a VM introduced in a recent patch
- Typo that breaks future uAPI compatibility in the verbs core
- More SELinux related oops fixing
- Fix an oops during error unwind in mlx5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IkGi
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"This is the next batch of for-rc patches from RDMA. It includes the
fix for the ipoib regression I mentioned last time, and the result of
a fairly major debugging effort to get iser working reliably on cxgb4
hardware - it turns out the cxgb4 driver was not handling QP error
flushing properly causing iser to fail.
- cxgb4 fix for an iser testing failure as debugged by Steve and
Sagi. The problem was a driver bug in the handling of shutting down
a QP.
- Various vmw_pvrdma fixes for bogus WARN_ON, missed resource free on
error unwind and a use after free bug
- Improper congestion counter values on mlx5 when link aggregation is
enabled
- ipoib lockdep regression introduced in this merge window
- hfi1 regression supporting the device in a VM introduced in a
recent patch
- Typo that breaks future uAPI compatibility in the verbs core
- More SELinux related oops fixing
- Fix an oops during error unwind in mlx5"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix mlx5_ib_alloc_mr error flow
IB/core: Verify that QP is security enabled in create and destroy
IB/uverbs: Fix command checking as part of ib_uverbs_ex_modify_qp()
IB/mlx5: Serialize access to the VMA list
IB/hfi: Only read capability registers if the capability exists
IB/ipoib: Fix lockdep issue found on ipoib_ib_dev_heavy_flush
IB/mlx5: Fix congestion counters in LAG mode
RDMA/vmw_pvrdma: Avoid use after free due to QP/CQ/SRQ destroy
RDMA/vmw_pvrdma: Use refcount_dec_and_test to avoid warning
RDMA/vmw_pvrdma: Call ib_umem_release on destroy QP path
iw_cxgb4: when flushing, complete all wrs in a chain
iw_cxgb4: reflect the original WR opcode in drain cqes
iw_cxgb4: Only validate the MSN for successful completions
While in recovery process of PCI error (called EEH on PowerPC arch),
another PCI transaction could be corrupted causing a situation of
nested PCI errors. Also, this scenario could be reproduced with
error injection mechanisms (for debug purposes).
We observe that in case of nested PCI errors, bnx2x might attempt to
initialize its shmem and cause a kernel crash due to bad addresses
read from MCP. Multiple different stack traces were observed depending
on the point the second PCI error happens.
This patch avoids the crashes by:
* failing PCI recovery in case of nested errors (since multiple
PCI errors in a row are not expected to lead to a functional
adapter anyway), and by,
* preventing access to adapter FW when MCP is failed (we mark it as
failed when shmem cannot get initialized properly).
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Shahed Shaikh <Shahed.Shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A customer noticed RX path hang when MTU is changed on the fly while
running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720
belongs to same ASIC family, we observed same issue and same fix
could solve this problem for 5720.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of AMD based server with 5762 hangs with jumbo frame traffic.
This AMD platform has southbridge limitation which is restricting MRRS
to 4000. As a work around, driver to restricts the MRRS to 2048 for
this particular 5762 NX1 card.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko