To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
The conversion wasn't quite straight forward because .config() and
.enable() were special to effectively swap their usual order. This resulted
in calculating the required values twice in some cases when
pwm_apply_state() was called. This is optimized en passant, and the order
of the callbacks is preserved without special jumping through hoops.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to drop the platform_driver's remove function. This is the
only user of driver data so this can go away, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
With the previous commit there is no need for the lowlevel driver any
more to specify it it uses two or three cells. So simplify accordingly.
The only non-trival change affects the pwm-rockchip driver: It used to only
support three cells if the hardware supports polarity. Now the default
number depends on the device tree which has to match hardware anyhow
(and if it doesn't the error is just a bit delayed as a PWM handle with
an inverted setting is catched when pwm_apply_state() is called).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing.) Also if disabling an enabled PWM was the right thing to do, this
should better be done in the framework instead of in each low level driver.
So drop the hardware modification from the .remove() callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The only side effect of this change is that pwm->state.polarity is
initialized to PWM_POLARITY_NORMAL instead of PWM_POLARITY_INVERSED.
However all other members of pwm->state are uninitialized and consumers
are expected to provide the right polarity (either by setting it explicitly
or by using a helper like pwm_init_state() that overwrites .polarity
anyhow with a value independent of the initial value).
The eventual goal is to remove pwmchip_add_with_polarity() and so simplify
the data flow in the PWM core.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since commit 5e5da1e9fb ("pwm: ab8500: Explicitly allocate pwm chip
base dynamically") all drivers use dynamic ID allocation explicitly. New
drivers are supposed to do the same, so remove support for driver
specified base IDs and drop all assignments in the low-level drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
'dc' here is an unsigned long, thus checking for <0 will always
evaluate to false.
Fixes the following W=1 warning:
drivers/pwm/pwm-bcm-kona.c:141:35: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-pwm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
All PWM devices have been marked as "might sleep" since v4.5, there is
no longer a need to differentiate on a per-chip basis.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Update the driver so that settings are applied in accordance with the
most recent version of the hardware spec. The revised sequence clears
the trigger bit, waits 400ns, writes settings, sets the trigger bit,
and waits another 400ns. This corrects an issue where occasionally a
requested change was not properly reflected in the PWM output.
Reviewed-by: Arun Ramamurthy <arunrama@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use the pwm_get_xxx() helpers instead of directly accessing the fields
in struct pwm_device. This will allow us to smoothly move to the atomic
update approach.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Some PWM drivers are testing the PWMF_ENABLED flag. Create a helper
function to hide the logic behind enabled test. This will allow us to
smoothly move from the current approach to an atomic PWM update
approach.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Omit setting the polarity to normal during probe and instead use the new
pwmchip_add_with_polarity() function to register a PWM chip with inverse
polarity by default for all channels to reflect the hardware default.
Signed-off-by: Arun Ramamurthy <arunrama@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
[thierry.reding@gmail.com: use pwmchip_add_with_polarity()]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for the six-channel Kona PWM controller found on Broadcom
mobile SoCs like bcm281xx.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Uwe Kleine-König