The proper name is Exynos Auto V9, not V0. It was the typo slipped in
unnoticed, fix it.
Fixes: b603377e40 ("soc: samsung: Add USI driver")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220114144606.24358-1-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
USIv2 IP-core is found on modern ARM64 Exynos SoCs (like Exynos850) and
provides selectable serial protocol (one of: UART, SPI, I2C). USIv2
registers usually reside in the same register map as a particular
underlying protocol it implements, but have some particular offset. E.g.
on Exynos850 the USI_UART has 0x13820000 base address, where UART
registers have 0x00..0x40 offsets, and USI registers have 0xc0..0xdc
offsets. Desired protocol can be chosen via SW_CONF register from System
Register block of the same domain as USI.
Before starting to use a particular protocol, USIv2 must be configured
properly:
1. Select protocol to be used via System Register
2. Clear "reset" flag in USI_CON
3. Configure HWACG behavior (e.g. for UART Rx the HWACG must be
disabled, so that the IP clock is not gated automatically); this is
done using USI_OPTION register
4. Keep both USI clocks (PCLK and IPCLK) running during USI registers
modification
This driver implements the above behavior. Of course, USIv2 driver
should be probed before UART/I2C/SPI drivers. It can be achieved by
embedding UART/I2C/SPI nodes inside of the USI node (in Device Tree);
driver then walks underlying nodes and instantiates those. Driver also
handles USI configuration on PM resume, as register contents can be lost
during CPU suspend.
This driver is designed with different USI versions in mind. So it
should be relatively easy to add new USI revisions to it later.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211204195757.8600-3-semen.protsenko@linaro.org
Tested-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The Exynos ChipID driver, like most of the Exynos drivers, uses one
compatible for entire family of compatible devices using one devicetree
"compatible". The compatibility is here described by programming
interface (register layout), not by actual values, so the product ID
register on one family of devices has different values for different
SoCs.
Describe which SoC goes with which compatible for documentation
purposes, if the DTS is not available in mainline.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211031205212.59505-1-krzysztof.kozlowski@canonical.com
The product id of Exynos Auto v9 is "0xAAA8_0000". Add this id and its
name.
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20211021012017.158919-2-chanho61.park@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add chip-id support for Exynos850 SoC. Despite its "E3830" ID, the
actual SoC name is Exynos850 (Exynos3830 name is internal and outdated).
Format of Product_ID register in Exynos850 (offset 0x0):
[31:0] Product ID (identification)
Format of CHIPID_REV register in Exynos850 (offset 0x10):
[23:20] Main revision
[19:16] Sub revision
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211014133508.1210-3-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Old Exynos SoCs have both Product ID and Revision ID in one single
register, while new SoCs tend to have two separate registers for those
IDs. Implement handling of both cases by passing Revision ID register
offsets in driver data.
Previously existing macros for Exynos4210 (removed in this patch) were
incorrect:
#define EXYNOS_SUBREV_MASK (0xf << 4)
#define EXYNOS_MAINREV_MASK (0xf << 0)
Actual format of PRO_ID register in Exynos4210 (offset 0x0):
[31:12] Product ID
[9:8] Package information
[7:4] Main Revision Number
[3:0] Sub Revision Number
This patch doesn't change the behavior on existing platforms, so
'/sys/devices/soc0/revision' will show the same string as before.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Henrik Grimler <henrik@grimler.se>
Link: https://lore.kernel.org/r/20211014133508.1210-1-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
After converting the Exynos ChipID and ASV driver to a module, allow to
actually choose it to be a module, while being a default built-in. The
side effect is that driver could be now entirely disabled even for
kernel with ARCH_EXYNOS, but this is not a critical issue because driver
is not necessary for the proper platform boot.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Tested-by: Sylwester Nawrocki <snawrocki@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20210919093114.35987-4-krzysztof.kozlowski@canonical.com
Exynos ChipID and ASV (Adaptive Supply Voltage) driver is not essential
to system boot and it can successfully be built and loaded as module.
This makes core kernel image smaller and reduces the memory footprint
when multi-platform kernel is booted on non-Exynos board. Usually it is
also distro-friendly.
Add multiple authors of the driver since its conversion from
mach-exynos, ordered alphabetically by first name.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Tested-by: Sylwester Nawrocki <snawrocki@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20210919093114.35987-3-krzysztof.kozlowski@canonical.com
soc_device_to_device() seems to be discouraged [1] so remove it in favor
of printing info message with platform device. This will only change
the prefix in the info message from "soc soc0: " to "exynos-chipid
10000000.chipid:".
[1] https://lore.kernel.org/lkml/20191111052741.GB3176397@kroah.com/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Tested-by: Sylwester Nawrocki <snawrocki@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20210919093114.35987-2-krzysztof.kozlowski@canonical.com
Commit 93618e344a ("soc: samsung: exynos-pmu: instantiate clkout
driver as MFD") adds a "devm_mfd_add_devices" call in the exynos-pmu
driver which depends on CONFIG_MFD_CORE. If no driver selects that
config, the build will fail if CONFIG_EXYNOS_PMU is enabled with the
following error:
drivers/soc/samsung/exynos-pmu.c:137: undefined reference to `devm_mfd_add_devices'
Fix this by making CONFIG_EXYNOS_PMU select CONFIG_MFD_CORE.
Fixes: 93618e344a ("soc: samsung: exynos-pmu: instantiate clkout driver as MFD")
Cc: <stable@vger.kernel.org>
Signed-off-by: David Virag <virag.david003@gmail.com>
Link: https://lore.kernel.org/r/20210909222812.108614-1-virag.david003@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
When Exynos power domain driver was introduced, the only way to ensure
that power domains will be instantiated before the devices which belongs
to them was to initialize them early enough, before the devices are
instantiated in the system. This in turn required not to use any platform
device infrastructure at all, as there have been no way to ensure proper
probe order between devices.
This has been finally changed and upcomming patch "driver core: Set
fw_devlink=on by default" ensures that each device will be probbed only
when its resource providers are ready. This allows to convert Exynos
power domain driver to regular platform driver.
This is also required by the mentioned commit to enable probing any
device which belongs to the Exynos power domains, as otherwise the core
won't notice that the power domains are in fact available.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20210113110320.13149-1-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
After converting to builtin driver, the probe function should not call
__init functions anymore:
>> WARNING: modpost: vmlinux.o(.text+0x8884d4):
Section mismatch in reference from the function exynos_chipid_probe() to the function .init.text:product_id_to_soc_id()
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 352bfbb3e0 ("soc: samsung: exynos-chipid: convert to driver and merge exynos-asv")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210105174440.120041-1-krzk@kernel.org
The Exynos Chip ID driver on Exynos SoCs has so far only informational
purpose - to expose the SoC device in sysfs. No other drivers depend on
it so there is really no benefit of initializing it early.
The code would be the most flexible if converted to a regular driver.
However there is already another driver - Exynos ASV (Adaptive Supply
Voltage) - which binds to the device node of Chip ID.
The solution is to convert the Exynos Chip ID to a built in driver and
merge the Exynos ASV into it.
This has several benefits:
1. Although the Exynos ASV driver binds to a device node present in all
Exynos DTS (generic compatible), it fails to probe except on the
supported ones (only Exynos5422). This means that the regular boot
process has a planned/normal device probe failure.
Merging the ASV into Chip ID will remove this probe failure because
the final driver will always bind, just with disabled ASV features.
2. Allows to use dev_info() as the SoC bus is present (since
core_initcall).
3. Could speed things up because of execution of Chip ID code in a SMP
environment (after bringing up secondary CPUs, unlike early_initcall),
This reduces the amount of work to be done early, when the kernel has
to bring up critical devices.
5. Makes the Chip ID code defer-probe friendly,
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201207190517.262051-5-krzk@kernel.org
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
If regmap_read() fails, the product_id local variable will contain
random value from the stack. Do not try to parse such value and fail
the ASV driver probe.
Fixes: 5ea428595c ("soc: samsung: Add Exynos Adaptive Supply Voltage driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Link: https://lore.kernel.org/r/20201207190517.262051-3-krzk@kernel.org
Check if the SoC is really supported before gathering the needed
resources. This fixes endless deferred probe on some SoCs other than
Exynos5422 (like Exynos5410).
Fixes: 5ea428595c ("soc: samsung: Add Exynos Adaptive Supply Voltage driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Link: https://lore.kernel.org/r/20201207190517.262051-2-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Exynos ChipID driver on Exynos SoCs has only informational
purpose - to expose the SoC device in sysfs. No other drivers
depend on it so there is really no benefit of initializing it early.
Instead, initialize everything with arch_initcall which:
1. Allows to use dev_info() as the SoC bus is present (since
core_initcall),
2. Could speed things up because of execution in a SMP environment
(after bringing up secondary CPUs, unlike early_initcall),
3. Reduces the amount of work to be done early, when the kernel has to
bring up critical devices.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201202195955.128633-2-krzk@kernel.org
Fixes the following W=1 kernel build warning(s):
drivers/soc/samsung/s3c-pm-check.c:162: warning: Function parameter or member 'val' not described in 's3c_pm_runcheck'
drivers/soc/samsung/s3c-pm-check.c:162: warning: Excess function parameter 'vak' description in 's3c_pm_runcheck'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Ben Dooks <ben@simtec.co.uk>
Link: https://lore.kernel.org/r/20201103152838.1290217-15-lee.jones@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Exynos clock output (clkout) driver uses same register address space
(Power Management Unit address space) as Exynos PMU driver and same set
of compatibles. It was modeled as clock provider instantiated with
CLK_OF_DECLARE_DRIVER().
This however brings ordering problems and lack of probe deferral,
therefore clkout driver should be converted to a regular module and
instantiated as a child of PMU driver to be able to use existing
compatibles and address space.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201001165646.32279-2-krzk@kernel.org
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
1. Clear unneeded L2C-310 flag which presenc was triggering warning
message.
2. Fix build of SAMSUNG_PM_DEBUG without MMU.
3. Minor cleanups and update of linux-samsung-soc mailing list in
Maintainers.
-----BEGIN PGP SIGNATURE-----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=Bkfy
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung mach/soc changes for v5.10
1. Clear unneeded L2C-310 flag which presenc was triggering warning
message.
2. Fix build of SAMSUNG_PM_DEBUG without MMU.
3. Minor cleanups and update of linux-samsung-soc mailing list in
Maintainers.
* tag 'samsung-soc-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: exynos: clear L310_AUX_CTRL_NS_LOCKDOWN in default l2c_aux_val
Signed-off-by: Olof Johansson <olof@lixom.net>
The OPP core manages various resources, e.g. clocks or interconnect paths.
These resources are looked up when the OPP table is allocated once
dev_pm_opp_get_opp_table() is called the first time (either directly
or indirectly through one of the many helper functions).
At this point, the resources may not be available yet, i.e. looking them
up will result in -EPROBE_DEFER. Unfortunately, dev_pm_opp_get_opp_table()
is currently unable to propagate this error code since it only returns
the allocated OPP table or NULL.
This means that all consumers of the OPP core are required to make sure
that all necessary resources are available. Usually this happens by
requesting them, checking the result and releasing them immediately after.
For example, we have added "dev_pm_opp_of_find_icc_paths(dev, NULL)" to
several drivers now just to make sure the interconnect providers are
ready before the OPP table is allocated. If this call is missing,
the OPP core will only warn about this and then attempt to continue
without interconnect. This will eventually fail horribly, e.g.:
cpu cpu0: _allocate_opp_table: Error finding interconnect paths: -517
... later ...
of: _read_bw: Mismatch between opp-peak-kBps and paths (1 0)
cpu cpu0: _opp_add_static_v2: opp key field not found
cpu cpu0: _of_add_opp_table_v2: Failed to add OPP, -22
This example happens when trying to use interconnects for a CPU OPP
table together with qcom-cpufreq-nvmem.c. qcom-cpufreq-nvmem calls
dev_pm_opp_set_supported_hw(), which ends up allocating the OPP table
early. To fix the problem with the current approach we would need to add
yet another call to dev_pm_opp_of_find_icc_paths(dev, NULL).
But actually qcom-cpufreq-nvmem.c has nothing to do with interconnects...
This commit attempts to make this more robust by allowing
dev_pm_opp_get_opp_table() to return an error pointer. Fixing all
the usages is trivial because the function is usually used indirectly
through another helper (e.g. dev_pm_opp_set_supported_hw() above).
These other helpers already return an error pointer.
The example above then works correctly because set_supported_hw() will
return -EPROBE_DEFER, and qcom-cpufreq-nvmem.c already propagates that
error. It should also be possible to remove the remaining usages of
"dev_pm_opp_of_find_icc_paths(dev, NULL)" from other drivers as well.
Note that this commit currently only handles -EPROBE_DEFER for the
clock/interconnects within _allocate_opp_table(). Other errors are just
ignored as before. Eventually those should be propagated as well.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ Viresh: skip checking return value of dev_pm_opp_get_opp_table() for
EPROBE_DEFER in domain.c, fix NULL return value and reorder
code a bit in core.c, and update exynos-asv.c ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This is the only part of plat-samsung that is really
shared between the s3c and s5p ports. Moving it to
drivers/soc/ lets us make them completely independent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200806182059.2431-16-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a simple custom voltage regulator coupler for Exynos5800 SoCs, which
require coupling between "vdd_arm" and "vdd_int" regulators. This coupler
ensures that the voltage values don't go below the bootloader-selected
operation point during the boot process until the clients set their
constraints. It is achieved by assuming minimal voltage value equal to
the current value if no constraints are set. This also ensures proper
voltage balancing if any of the client driver is missing.
The balancing code comes from the regulator/core.c with the additional
logic for handling regulators without client constraints applied added.
Link: https://lore.kernel.org/r/20200721180900.13844-5-krzk@kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Correct the probe return value to -ENODEV on non-Exynos platforms.
Link: https://lore.kernel.org/r/20200316175652.5604-4-krzk@kernel.org
Fixes: 02fb29882d ("soc: samsung: chipid: Drop "syscon" compatible requirement")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The dev_pm_opp_get_opp_table() returns error pointers if it's disabled
in the config and it returns NULL if there is an error. This code only
checks for error pointers so it could lead to an Oops inside the
dev_pm_opp_put_opp_table() function.
Fixes: 5ea428595c ("soc: samsung: Add Exynos Adaptive Supply Voltage driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As we dropped the requirement of "syscon" compatible in the chipid
nodes rework code acquiring the regmap to use device_node_to_regmap()
rather than syscon_node_to_regmap().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Adaptive Supply Voltage (ASV) driver adjusts CPU cluster operating
points depending on exact revision of an SoC retrieved from the CHIPID
block or the OTP memory. This allows for some power saving as for some
CPU clock frequencies we can lower CPU cluster's supply voltage comparing
to safe values common to all the SoC revisions.
This patch adds support for Exynos5422/5800 SoC, it is partially based
on code from https://github.com/hardkernel/linux repository,
branch odroidxu4-4.14.y, files: arch/arm/mach-exynos/exynos5422-asv.[ch].
Tested on Odroid XU3, XU4, XU3 Lite.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The chipid driver uses the MFD syscon API but it was not covered
properly in Kconfig.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In commit 40d8aff614 ("soc: samsung: chipid: Convert exynos-chipid
driver to use the regmap API") of_find_compatible_node() call was
substituted with syscon_regmap_lookup_by_compatible() but also an error
log was added for case where lookup fails. On multiplatform the lookup
will always fail on any non-samsung device so the log is incorrect.
Remove the error log and just return an error code from
syscon_regmap_lookup_by_compatible() which internally calls
of_find_compatible_node().
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently when the call to product_id_to_soc_id fails there
is a memory leak of soc_dev_attr->revision and soc_dev_attr
on the error return path. Fix this by adding a common error
return path that frees there obects and use this for two
error return paths.
Addresses-Coverity: ("Resource leak")
Fixes: 3253b7b7cd ("soc: samsung: Add exynos chipid driver support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Convert the driver to use regmap API in order to allow other
drivers, like ASV, to access the CHIPID registers.
Add definition of selected CHIPID register offsets and register bit
fields for Exynos5422 SoC.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos SoCs have Chipid, for identification of product IDs and SoC
revisions. This patch intends to provide initialization code for all
these functionalities, at the same time it provides some sysfs entries
for accessing these information to user-space.
This driver uses existing binding for exynos-chipid.
Changes by Bartlomiej:
- fixed return values on errors
- removed bogus kfree_const()
- added missing Exynos4210 EVT0 id
- converted code to use EXYNOS_MASK define
- fixed np use after of_node_put()
- fixed too early use of dev_info()
- made driver fail for unknown SoC-s
- added SPDX tag
- updated Copyrights
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
[m.szyprowski: for suggestion and code snippet of product_id_to_soc_id]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[s.nawrocki: updated copyright date, removed uneeded headers inclusion]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Handling of special clock operations on power domain on/off sequences has
been moved to respective Exynos clock controller drivers, so there is no
need to keep the duplicated (and conflicting) code in Exynos power domain
driver. Mark clock related properties in Exynos power domain bindings as
deprecated. This change has no inpact on backwards-compatibility, as the
new drivers properly work with old DTBs (deprecated properties are
ignored).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
for the TI Davinci family of SoCs. So far those clks have been supported
with a custom implementation of the clk API in the arch port instead of in
the CCF. With this driver merged we're one step closer to having a single
clk API implementation.
The other large diff is from the Amlogic clk driver that underwent some
major surgery to use regmap. Beyond that, the biggest hitter is Samsung
which needed some reworks to properly handle clk provider power domains
and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some cleanups
and small fixes for some of the more esoteric features. And the usual
set of driver non-critical fixes, cleanups, and minor additions are here as
well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC
-----BEGIN PGP SIGNATURE-----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=ys4O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
Clocks related to DISP1 block require special handling for power domain
turn on/off sequences. Till now this was handled by Exynos power domain
driver, but that approach was limited only to some special cases. This
patch moves handling of those operations to clock controller driver.
This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5250 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Clocks related to DISP, GSC and MFC blocks require special handling for
power domain turn on/off sequences. Till now this was handled by Exynos
power domain driver, but that approach was limited only to some special
cases. This patch moves handling of those operations to clock controller
driver. This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5420 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Handling of clock reparenting will be move to clock controller driver,
so add possibility to blacklist clock handling on systems, where the
clock controller already does all needed operations. This is needed
to avoid potential deadlock on clock reparenting during power domain
on/off procedure.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The syscon poweroff and restart nodes logically belong to the Power
Management Unit so populate possible children.
This also requires providing compatibles for Exynos5410 and Exynos7 so
the PMU device and its children will be instantiated for them as well.
Just like Exynos5433, these chipsets are not yet supported by the PMU
driver.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Support for Exynos4212 SoCs has been removed by commit bca9085e0a ("ARM:
dts: exynos: remove Exynos4212 support (dead code)"), so there is no need
to keep remaining dead code related to this SoC version.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Conversion to kbasename from Rob Herring.
-----BEGIN PGP SIGNATURE-----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=gwbs
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Pull "Samsung soc drivers changes for v4.14" from Krzysztof Kozłowski:
Conversion to kbasename from Rob Herring.
* tag 'samsung-drivers-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: Use kbasename instead of open coding
Krzysztof Kozlowski