Allow setting a probe response template for an interface operating in
AP mode. Low level drivers are notified about changes in the probe
response template and are able to retrieve a copy of the current probe
response. This data can, for example, be uploaded to hardware as a
template.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Attempting to micro-optimise the scan by going
fully live again when scanning the operating
channel just made the code extremely complex
and has little gain in most use cases. Remove
all that code and simplify the state machine
again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the socket wifi TX status error
queue reflection in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there's an interface in AP mode, OBSS beacons
are needed by hostapd/wpa_s to implement logic to
enable/disable protection etc. Report the frames
and set the capability flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver is never informed about monitor or
AP_VLAN interfaces, so whenever we pass those
to it later this is a bug. Verify we don't as
there are some cases where this could happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some refactoring for IBSS HT.
Move HT info and capability IEs building code into separate functions.
Add function to get the channel type from an HT info IE.
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only AID values 1-2007 are valid, but some APs have been
found to send random bogus values, in the reported case an
AP that was sending the AID field value 0xffff, an AID of
0x3fff (16383).
There isn't much we can do but disable powersave since
there's no way it can work properly in this case.
Cc: stable@vger.kernel.org
Reported-by: Bill C Riemers <briemers@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of the ieee80211_tx_status_rtap_hdr struct and instead build the
rtap header dynamically. This makes it easier to extend the rtap header
generation in the future.
Add ieee80211_tx_radiotap_len to calculate the expected size of the
rtap header before generating it. Since we can't check if the rtap
header fits into the requested headroom during compile time anymore
add a WARN_ON_ONCE.
Also move the actual rtap header generation into its own function.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The purpose of this is two-fold:
1) by moving it out of tx_data.flags, we can in
another patch move the radiotap parsing so it
no longer is in the hotpath
2) if a device implements fragmentation but can
optionally skip it, the radiotap request for
not doing fragmentation may be honoured
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I introduced in-kernel off-channel TX I
introduced a bug -- the work can't be canceled
again because the code clear the skb pointer.
Fix this by keeping track separately of whether
TX status has already been reported.
Cc: stable@kernel.org [2.6.38+]
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi has a separate EOSP notification from
the device, and to make use of that properly
it needs to be passed to mac80211. To be able
to mix with tx_status_irqsafe and rx_irqsafe
it also needs to be an "_irqsafe" version in
the sense that it goes through the tasklet,
the actual flag clearing would be IRQ-safe
but doing it directly would cause reordering
issues.
This is needed in the case of a P2P GO going
into an absence period without transmitting
any frames that should be driver-released as
in this case there's no other way to inform
mac80211 that the service period ended. Note
that for drivers that don't use the _irqsafe
functions another version of this function
will be required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PS-poll, there's a possible race between
us expiring a frame and the station polling
for it -- send it a null frame in that case.
For uAPSD, the standard says that we have to
send a frame in each SP, so send null if we
don't have any other frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we no longer use the return value, we no
longer need to maintain it either, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
save and configure tx param per sdata, rather than
per hardware.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assumption is that during the hw config, transmission was
already stopped by mac80211. Sometimes the AP can be switching
b/w the ht modes due to intolerant or etc where STA is in
the middle of transmission. In such scenario, buffer overflow
was observed at driver side. And also before updating the rate
control, the frames are continued to xmited with older rates.
This patch ensures that the frames are always xmitted with
updated rates and avoid buffer overflow.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tx flow control for non-mesh modes of operation only needs to act on the
net device queues: when the hardware queues are full we stop accepting
traffic from the net device. In mesh, however, we also need to stop
forwarding traffic. This patch checks the hardware queues before
attempting to forward a mesh frame.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To properly maintain the peer's block ack window, the driver needs to be
able to control the new starting sequence number that is sent along with
the BlockAckReq frame.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In this implementation, a mesh gate is a root node with a certain bit
set in its RANN flags. The mpath to this root node is marked as a path
to a gate, and added to our list of known gates for this if_mesh. Once a
path discovery process fails, we forward the unresolved frames to a
known gate. Thanks to Luis Rodriguez for refactoring and bug fix help.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving the parsing logic for retrieving the information elements
stored in management frames, e.g. beacons or probe responses,
and making it available to other cfg80211 drivers.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For iwlwifi, I decided not to use this API since
it just increased the complexity for little gain.
Since nobody else intends to use it, let's kill
it again. If anybody later needs to have it, we
can always revive it then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In P2P client mode, the GO (AP) to connect to might
have periods of time where it is not available due
to powersave. To allow the driver to sync with it
and send frames to the GO only when it is available
add a new callback tx_sync (and the corresponding
finish_tx_sync). These callbacks can sleep unlike
the actual TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scanning currently uses the TX rate mask to
restrict the rate set, which is bogus. Make
it use the new set of rates from userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add tx_conf array to save the current tx queues
configuration, and reconfig it on resume (ieee80211_reconfig).
On resume, the driver is being reconfigured. Without
reconfiguring the tx queues as well, the driver might
configure the device to use wrong ac params (e.g. ps-poll
instead of uapsd).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In WoWLAN, devices may use crypto keys for TX/RX
and could also implement GTK rekeying. If the
driver isn't able to retrieve replay counters and
similar information from the device upon resume,
or if the device isn't responsive due to platform
issues, it isn't safe to keep the connection up
as GTK rekey messages from during the sleep time
could be replayed against it.
The only protection against that is disconnecting
from the AP. Modifying mac80211 to do that while
it is resuming would be very complex and invasive
in the case that the driver requires a reconfig,
so do it after it has resumed completely. In that
case, however, packets might be replayed since it
can then only happen after TX/RX are up again, so
mark keys for interfaces that need to disconnect
as "tainted" and drop all packets that are sent
or received with those keys.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 maintains a running average of the RSSI when a STA
is associated to an AP. Report threshold events to any driver
that has registered callbacks for getting RSSI measurements.
Implement callbacks in mac80211 so that driver can set thresholds.
Add callbacks in mac80211 which is invoked when an RSSI threshold
event occurs.
mac80211: add tracing to rssi_reports api and remove extraneous fn argument
mac80211: scale up rssi thresholds from driver by 16 before storing
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current rx->queue value is slightly confusing.
It is set to 16 on non-QoS frames, including data,
and then used for sequence number and PN/IV checks.
Until recently, we had a TKIP IV checking bug that
had been introduced in 2008 to fix a seqno issue.
Before that, we always used TID 0 for checking the
PN or IV on non-QoS packets.
Go back to the old status for PN/IV checks using
the TID 0 counter for non-QoS by splitting up the
rx->queue value into "seqno_idx" and "security_idx"
in order to avoid confusion in the future. They
each have special rules on the value used for non-
QoS data frames.
Since the handling is now unified, also revert the
special TKIP handling from my patch
"mac80211: fix TKIP replay vulnerability".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on inputs from Johannes Berg <johannes@sipsolutions.net>
from http://article.gmane.org/gmane.linux.kernel.wireless.general/68193
and http://article.gmane.org/gmane.linux.kernel.wireless.general/71702
In xmit path, devices that do full hardware crypto (including
MMIC and ICV) need no tailroom. For such devices, tailroom
reservation can be skipped if all the keys are programmed into
the hardware (i.e software crypto is not used for any of the
keys) and none of the keys wants software to generate Michael
MIC and IV.
v2: Added check for IV along with MMIC.
Reported-by: Fabio Rossi <rossi.f@inwind.it>
Tested-by: Fabio Rossi <rossi.f@inwind.it>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Cc: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
v3: Fixing races to avoid WARNING: at net/mac80211/wpa.c:397
ccmp_encrypt_skb+0xc4/0x1f0
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
v4: Added links with message ID
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not send DS Channel parameter for directed probe requests
in order to maximize the chance that we get a response. Some
badly-behaved APs don't respond when this parameter is included.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds sparse RCU annotations to most of
mac80211, only the mesh code remains to be
done.
Due the the previous patches, the annotations
are pretty simple. The only thing that this
actually changes is removing the RCU usage of
key->sta in debugfs since this pointer isn't
actually an RCU-managed pointer (it only has
a single assignment done before the key even
goes live). As that is otherwise harmless, I
decided to make it part of this patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sched_scan_stopped was called by the driver, mac80211 calls
cfg80211, which in turn was calling mac80211 back with a flag
"driver_initiated". This flag was used so that mac80211 would do the
necessary cleanup but would not call the driver. This was enough to
prevent the bounce back between the driver and mac80211, but not
between mac80211 and cfg80211.
To fix this, we now do the cleanup in mac80211 before calling
cfg80211. To help with locking issues, the workqueue was moved from
cfg80211 to mac80211.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement support for HW scheduled scan. The mac80211 code doesn't perform
scheduled scans itself, but calls the driver to start and stop scheduled
scans.
This patch also creates a trace event class to be used by drv_hw_scan
and the new drv_sched_scan_start and drv_sched_stop functions, in
order to avoid duplicate code.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new configuration option to support AMPE from userspace.
Prior to this series we only supported authentication in userspace: an
authentication daemon would authenticate peer candidates in userspace
and hand them over to the kernel. From that point the mesh stack would
take over and establish a peer link (Mesh Peering Management).
These patches introduce support for Authenticated Mesh Peering Exchange
in userspace. The userspace daemon implements the AMPE protocol and on
successfull completion create mesh peers and install encryption keys.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds basic support for the new WoWLAN
configuration in mac80211. The behaviour is
completely offloaded to the driver though,
with two new callbacks (suspend/resume).
Options for the driver include a complete
reconfiguration after wakeup, and exposing
all the triggers it wants to support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In xmit path, devices that do full hardware crypto (including
TKIP MMIC) need no tailroom. For such devices, tailroom
reservation can be skipped if all the keys are programmed into
the hardware (i.e software crypto is not used for any of the
keys) and none of the keys wants software to generate Michael
MIC.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To NL80211_MESH_SETUP_IE. This reflects our ability to insert any ie
into a mesh beacon, not simply path selection ies.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only thing that using crypto_blkcipher with ecb does over just using
arc4 directly is wrapping the encrypt/decrypt function into a for loop,
looping over each individual character.
To be able to do this, it pulls in around 40 kb worth of unnecessary
kernel modules (at least on a MIPS embedded device).
Using arc4 directly not only eliminates those dependencies, it also makes
the code smaller.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For devices supported by iwlwifi sometimes
off-channel transmissions need to be handled
by the device completely. To support this
mac80211 needs to pass the frame directly
to the driver and not through the TX path
as the driver needs the frame and channel
information at the same time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module parameter ieee80211_disable_40mhz_24ghz
was meant to allow disabling 40 MHz operation in
the 2.4 GHz band by default. However, it is buggy
as implemented because while it advertises to the
AP that the device doesn't support 40 MHz, it will
itself still use 40 MHz configurations.
To fix this, clear the 40 MHz bits from the sband
completely instead of overriding where used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should decrease un-necessary flushes, on/off channel work,
and channel changes in cases where the only scanned channel is
the current operating channel.
* Removes SCAN_OFF_CHANNEL flag, uses SDATA_STATE_OFFCHANNEL
and is-scanning flags instead.
* Add helper method to determine if we are currently configured
for the operating channel.
* Do no blindly go off/on channel in work.c Instead, only call
appropriate on/off code when we really need to change channels.
Always enable offchannel-ps mode when starting work,
and disable it when we are done.
* Consolidate ieee80211_offchannel_stop_station and
ieee80211_offchannel_stop_beaconing, call it
ieee80211_offchannel_stop_vifs instead.
* Accept non-beacon frames when scanning on operating channel.
* Scan state machine optimized to minimize on/off channel
transitions. Also, when going on-channel, go ahead and
re-enable beaconing. We're going to be there for 200ms,
so seems like some useful beaconing could happen.
Always enable offchannel-ps mode when starting software
scan, and disable it when we are done.
* Grab local->mtx earlier in __ieee80211_scan_completed_finish
so that we are protected when calling hw_config(), etc.
* Pass probe-responses up the stack if scanning on local
channel, so that mlme can take a look.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arik Nemtsov