The i.MX27 DMA support was introduced with the initial commit of this
driver and originally created by me. However, I never got this stable
due to the racy DMA engine and used the EMMA engine instead. As the DMA
support is most probably unused and broken in its current state, remove
it. EMMA becomes the only supported mode on i.MX27.
This also helps us get rid of another user of the legacy i.MX DMA
support and remove the dependency on ARCH_MX* macros as these are
scheduled for removal.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[g.liakhovetski@gmx.de: remove unused goto]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error handling in lgdt3303_read_status() and lgdt330x_read_ucblocks()
doesn't work, because i2c_read_demod_bytes() returns a u8 and (err < 0)
is always false.
err = i2c_read_demod_bytes(state, 0x58, buf, 1);
if (err < 0)
return err;
Change the return type of i2c_read_demod_bytes() to int. Also change
the return value on error to -EIO to make (err < 0) work.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On MIPS/ARM set-top-boxes, as well as old x86 PCs, memory allocation failures
in the em28xx driver are common, due to memory fragmentation over time, that
makes impossible to allocate large chunks of coherent memory.
A typical system with 256/512 MB of RAM fails after just 1 day of uptime (see
the old thread for detailed reports and crashlogs).
In fact, the em28xx driver allocates memory for USB isoc transfers at runtime,
as opposite to the dvb-usb drivers that allocates the USB buffers when the
device is initialized, and frees them when the device is disconnected.
Moreover, in digital mode the USB isoc transfer buffers are freed, allocated
and cleared every time the user selects a new channel, wasting time and
resources.
This patch solves both problems by allocating DVB isoc transfer buffers in
em28xx_usb_probe(), and freeing them in em28xx_usb_disconnect().
In fact, the buffers size and number depend only on the max USB packet size
that is parsed from the USB descriptors in em28xx_usb_probe(), so it can
never change for a given device.
This approach makes no sense in analog mode (as the buffer size depends on
the alternate mode selected at runtime), the patch creates two separate sets
of buffers for digital and analog modes.
For digital-only devices, USB buffers are created when the device is probed
and freed when the device is disconnected.
For analog-only devices, nothing changes: isoc buffers are created at runtime.
For hybrid devices, two sets of buffers are maintained: the digital-mode
buffers are created when the device is probed, and freed when the device is
disconnected; analog-mode buffers are created/destroyed at runtime as before.
So, in analog mode, digital and analog buffers coexists at the same time: this
can be justified by the fact that digital mode is by far more commonly used
nowadays, so it makes sense to optimize the driver for this use case scenario.
The patch has been tested in the last few days on a x86 PC and a MIPS
set-top-box, with the PCTV 290e (digital only) and the Terratec Hybrid XS
(hybrid device). With the latter, I switched several times between analog and
digital mode (Kaffeine/TvTime) with no issue at all.
I unplugged/plugged the devices several times with no problem.
Also, after over 3 days of normal usage in the MPIS set-top-box, the PCTV 290e
was still up and running.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The signal strength value returned is not quite correct, it decreases
when I increase the gain of my antenna, and vice versa. It also
doesn't span over the whole 0x0000-0xffff range. Compute a value which
at least increases when signal strength increases, and spans the whole
allowed range.
In practice I get 67% with my antenna fully amplified and 51% with
no amplification. This is close enough to what I get on my other
DVB-T adapter with the same antenna.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Read signal strength using VAR_P_INBAND and apply FEC preferred values.
Note this does not work on IT9137 devices even with dvb-usb-it9135-01.fw
firmware.
Config read_sl allows switch between read signal strength and signal
level.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow PID 8192 to turn PID filter off in USB high speed.
The PID number is still written to the PID index and will only
turn on again if that index is set to 0.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some virtual I2C commands are missed along some PID filtering
commands resulting complete stall of driver.
Since dvb-usb cannot handle the -EAGAIN error and commands
generally should not be missed mutex_lock is used instead.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the drivers in drivers/media/* to use the
module_i2_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Heungjun Kim <riverful.kim@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Andrew Chew <achew@nvidia.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Johannes Obermaier <johannes.obermaier@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The exposure was not set when autogain was set.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The setexposure added in commit 590f216806 works only for the sensor hv7131r,
but it is called for all sensors when changing the autogain.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bridge register 11 reports the current transfer status.
This value is used to know about a possible overflow and to adjust
the transfer parameters (registers 07 and 08).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the bridge register 08 defines the JPEG compression quality,
it must be changed on JPEG quality change and also, the decompression
tables must be adjusted when the register varies.
[mchehab@redhat.com: replace a // comment by a /* */ one]
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The auto gain uses the knee algorithm.
Adding the setexposure control function forced to:
- rename of the previous function setexposure
- add a specific auto setting function
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_jcomp control is rarely used and its main information,
the JPEG quality, may be found in the images.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG header is always the same, so, it does not need to be rebuild
each time a new frame is received.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initialize the subdev name properly so it doesn't have an I2C
bus and slave address appended to it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initialize the subdev name properly so it doesn't have an I2C
bus and slave address appended to it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initialize the subdev name properly so it doesn't have an I2C
bus and slave address appended to it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adapt to new controls (subsampling).
For encoding, the destination format now needs to be set to V4L2_PIX_FMT_JPEG
and the subsampling (4:2:2 or 4:2:0) needs to be set using the respective
control (V4L2_CID_JPEG_CHROMA_SUBSAMPLING). Required buffer size for
destination image during encoding is no longer deduced from the format (which
generally implied overestimation), but needs to be given from userspace in
sizeimage.
Not strictly related to the added controls, this patch also fixes setting the
subsampling of the destination image for decoding, depending on the destination
format.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some video devices need to use contiguous memory which is
not backed by pages as it happens with vmalloc. This patch
provides USERPTR handling for those devices.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The devm_* functions are used in the platform device probe() for data
that is freed on driver removal. The managed device layer takes care
of undoing actions taken in the probe callback() and freeing resources
on driver detach. This eliminates the need for manually releasing
resources and simplifies error handling.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for cropping and composition setup on the video capture
node through VIDIOC_S/G_SELECTION ioctls. S/G_CROP, CROPCAP ioctls
are still supported for applications since the core will translate
them to *_selection handler calls.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The devm_* functions are used in the platform device probe() for data
that is freed on driver removal. The managed device layer takes care
of undoing actions taken in the probe callback() and freeing resources
on driver detach. This eliminates the need for manually releasing
resources and simplifies error handling.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver used the regulator API so it should depend on REGULATOR.
[mchehab@redhat.com: break depends on on two lines, instead of using a \]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Il 29/02/2012 22:30, Geert Uytterhoeven ha scritto:
> http://kisskb.ellerman.id.au/kisskb/buildresult/5759200/ ERROR:
> "__udivdi3" [drivers/media/dvb/frontends/rtl2830.ko] undefined!
>
The following patch fixed the warning on my 32 bit system.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replaces VIDIOC_S/G_JPEGCOMP ioctl handlers with
V4L2_CID_JPEG_QUALITY control. Additionally it enables JPEG subsampling
and the restart interval configuration through V4L2_CID_JPEG_SUBSAMPLING
and V4L2_CID_JPEG_RESTART_INTERVAL controls. For the decoder video node
only V4L2_CID_JPEG_SUBSAMPLING is available as a read-only control.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is a prerequisite for per file handle control handlers.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two issues on the default delivery system setting for smsusb:
1) instead of filling the delivery system for the per-client
frontend.ops, it were changing the global structure;
2) The client->frontend.ops copy were keeping the previous value
of the template. So, the first time the device was inserted,
it was using the wrong value.
Reported-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 382d19f197, as the
changes in question are done in v4l tree differently.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The V4L2_CID_JPEG_CLASS control class is intended to expose various
adjustable parameters of JPEG encoders and decoders. Following controls
are defined:
- V4L2_CID_JPEG_CHROMA_SUBSAMPLING,
- V4L2_CID_JPEG_RESTART_INTERVAL,
- V4L2_CID_JPEG_COMPRESSION_QUALITY,
- V4L2_CID_JPEG_ACTIVE_MARKER.
This covers only a part of relevant standard specifications. More
controls should be added in future if required.
The purpose of V4L2_CID_JPEG_CLASS class is also to replace some
functionality covered by VIDIOC_S/G_JPEGCOMP ioctls, i.e. the JPEG
markers presence and compression quality control. The applications
and drivers should switch from the ioctl to control based API, as
described in the subsequent patches for the Media API DocBook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware is not accessible when device is sleeping.
Preventing such IOCTLs when sleep should be job of DVB CORE...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* some style issues
* remove rtl2832u device IDs
* move USB IDs to correct place
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement I2C functionality according to real RTL2830 demod.
Do not send register page in first byte of each I2C write, instead
use logic to set page using own write when needed. Page register is
physical register 0 as generally used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not return error for demod attach in case of mxl5005s tuner.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For now it supports only Realtek RTL2831U chip.
RTL2831U is integrated DVB USB interface and DVB-T demod.
DVB-T demod integrated to RTL2831U is Realtek RTL2830.
Supported tuners are QT1010, MT2060 and MXL5005S.
Signed-off-by: Antti Palosaari <crope@iki.fi>
[mchehab@redhat.com: fix a small typo]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding support for using MHL (SiI9234 or other) chip if its configuration was
passed to HDMI by platfrom data.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Moving configuration of s5p-hdmi peripherals from driver data to
platfrom data.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SiI9234 is a converter of HDMI signal into MHL. The chip is present on some
boards from Samsung S5P family. The chip's configuration procedure is based on
MHD_SiI9234 driver created by doonsoo45.kim.
The driver is using:
- i2c framework
- v4l2 framework
- runtime PM
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 99ac541254 removed
the function mt2063_setTune() from mt2063.c. Remove it
also from the header file.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Included module.h explicitly to resolve the macros THIS_MODULE and
MODULE_LICENSE. This avoids compilations errors as those defines were not
declared.
Signed-off-by: Henrique Camargo <henrique@henriquecamargo.com>
Signed-off-by: Diogo Luvizon <diogoluvizon@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i.MX2x SoCs have a PrP which is capable of resizing and format
conversion of video frames. This driver provides support for
resizing and format conversion from YUYV to YUV420.
This operation is of the utmost importance since some of these
SoCs like i.MX27 include an H.264 video codec which only
accepts YUV420 as input.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use system timestamps if the timestamp can't be computed from the data
sent by the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] hdpvr: update picture controls to support firmware versions > 0.15
[media] wl128x: fix build errors when GPIOLIB is not enabled
[media] hdpvr: fix race conditon during start of streaming
[media] omap3isp: Fix crash caused by subdevs now having a pointer to devnodes
[media] imon: don't wedge hardware after early callbacks
Correctly sets the max/min/default values for the hdpvr picture
controls. The reason the current values didn't cause a problem until now
is because any firmware <= 0.15 didn't support them. The latest firmware
releases properly support picture controls and the values in the patch
are derived from the windows driver using SniffUSB2.0.
Thanks to Devin Heitmueller for helping me.
Signed-off-by: Taylor Ralph <tralph@mythtv.org>
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix wl128x Kconfig to depend on GPIOLIB since TI_ST also
depends on GPIOLIB.
(.text+0xe6d60): undefined reference to `st_register'
(.text+0xe7016): undefined reference to `st_unregister'
(.text+0xe70ce): undefined reference to `st_unregister'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Manjunatha Halli <manjunatha_halli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correctly sets the max/min/default values for the hdpvr picture
controls. The reason the current values didn't cause a problem until now
is because any firmware <= 0.15 didn't support them. The latest firmware
releases properly support picture controls and the values in the patch
are derived from the windows driver using SniffUSB2.0.
Thanks to Devin Heitmueller for helping me.
Signed-off-by: Taylor Ralph <tralph@mythtv.org>
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix wl128x Kconfig to depend on GPIOLIB since TI_ST also
depends on GPIOLIB.
(.text+0xe6d60): undefined reference to `st_register'
(.text+0xe7016): undefined reference to `st_unregister'
(.text+0xe70ce): undefined reference to `st_unregister'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Manjunatha Halli <manjunatha_halli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Specify chip revision at attach time rather than a firmware image.
This is a better way to ensure that the correct firmware is loaded
for the correct revision of the chip.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
convert the firmware configuration attach-time parameter from
a pointer to an integer so as to remove the static dependency
created by the previous changesets.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
newer versions of the xc5000 silicon require newer firmware
while remaining 100% driver compatible. original versions
of the xc5000a continue to use the same firmware.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Problems with the PID setting stalling demux on applications like VDR and MythTV.
The PID filter is now defaulted to OFF.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 7e07222 breaks DVBFE_ALGO_HW tuning after a retune is requested,
which causes bad tuning on my TBS 6920.
[ 0.769091] pci 0000:06:00.0: [14f1:8852] type 0 class 0x000400
[ 19.733530] CORE cx23885[0]: subsystem: 6920:8888, board: TurboSight TBS 6920 [card=14,autodetected]
[ 762.824912] cx24116_load_firmware: FW version 1.23.86.1
7e0722215a [media] dvb-core: Don't pass DVBv3 parameters on tune() fops
Although re_tune is set to true when FESTATE_RETUNE occurs, it is never
set back to false which the old code used to do when !FESTATE_RETUNE.
This patch sets re_tune to false if !(state & FESTATE_RETUNE).
$ szap-s2 -a 2 "Channel 5"
reading channels from file '/home/simon/.szap/channels.conf'
zapping to 247 'Channel 5':
delivery DVB-S, modulation QPSK
sat 0, frequency 10964 MHz H, symbolrate 22000000, coderate 5/6, rolloff 0.35
vpid 0x092a, apid 0x092b, sid 0x092d
using '/dev/dvb/adapter2/frontend0' and '/dev/dvb/adapter2/demux0'
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eb33 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cec0 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cec0 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with actual hardware (up to two cards) and the Keene USB FM Transmitter.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with actual hardware and the Keene USB FM Transmitter.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with actual hardware and the Keene USB FM Transmitter.
Improved the volume handling delays through trial and error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have quite a few ISA radio drivers, which are all very similar.
This framework makes it possible to reduce the code size of those drivers
and makes it much easier to keep them up to date with the latest V4L2 API
developments.
Drivers rewritten to use this framework fully pass the v4l2-compliance tests
and are properly using the ISA bus (so they can be found under /sys/bus/isa).
It is now also possible to support multiple cards using the same driver
(tested with two radio-gemtek cards).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for different types of remote.
ITE remotes share common device IDs with differently assigned keys.
Two versions of remote maps have been created there are likely to be more.
v1 for all other IDs
v2 for USB_PID_ITETECH_IT9135_9005.
This patch also separates the configuration parts from it913x_identify_state function.
TODO
remotes for HID interfaces.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
status has to be set to STREAMING before the streaming worker is
queued. hdpvr_transmit_buffers() will exit immediately otherwise.
Reported-by: Joerg Desch <vvd.joede@googlemail.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many drivers just support control events, and most radio drivers just need
to poll for control events. Add some functions to simplify those jobs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the start and end messages for log_status when called from a
subdev device node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For drivers that properly use the v4l2 framework (i.e. set v4l2_dev in the
video_device struct), the start and end messages of VIDIOC_LOG_STATUS are
now generated automatically. People tended to forget these, but the v4l2-ctl
tool scans for these messages, and it also makes it easier to read the status
output in the kernel log.
The cx18, ivtv and bttv drivers were changed since they no longer need to
log these start/end messages.
In saa7164 two empty log_status functions were removed.
Also added a helper function to v4l2-ctrl.c that can be used as the
vidioc_log_status callback if all you need to do is to log the current control
values. This is now used by pwc and vivi.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Steven Toth <stoth@kernellabs.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With this private ioctl it is possible to use the ivtv decoder without
requiring the dvb/video.h and dvb/audio.h headers.
Eventually support for those DVB APIs will be dropped from ivtv.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx18 and ddbridge drivers include linux/dvb/audio.h and video.h
without using them.
Remove those includes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As discussed during the 2011 V4L-DVB workshop we want to create a proper V4L2
decoder API that replaces the DVBv5 API that has been used until now.
This adds the four controls necessary to be able to switch ivtv over to this
new API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As discussed during the 2011 V4L-DVB workshop, the API in dvb/video.h should
be replaced by a proper V4L2 API. This patch turns the VIDEO_(TRY_)DECODER_CMD
ioctls into proper V4L2 ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for some -Wuninitialized compiler warnings.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In tm6000_ir_fini() there seems to be a problem.
rc_unregister_device(ir->rc); calls rc_free_device() on the pointer it is
given, which frees it.
Subsequently the function does:
if (!ir->polling)
__tm6000_ir_int_stop(ir->rc);
and __tm6000_ir_int_stop() dereferences the pointer it is given, which
has already been freed.
and it also does:
tm6000_ir_stop(ir->rc);
which also dereferences the (already freed) pointer.
So, it seems that the call to rc_unregister_device() should be move
below the calls to __tm6000_ir_int_stop() and tm6000_ir_stop(), so
those don't operate on a already freed pointer.
But, I must admit that I don't know this code *at all*, so someone who
knows the code should take a careful look before applying this
patch. It is based purely on inspection of facts of what is beeing
freed where and not at all on understanding what the code does or why.
I don't even have a means to test it, so beyond testing that the
change compiles it has seen no testing what-so-ever.
Anyway, here's a proposed patch.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some version 2 devices have different tuner IDs. ID 0x38
appears to have weak signal strength.
Apply default 0x60 to unknown IDs.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase mt2063 frequency_max to tune to channel 69(858Mhz).
Jose Alberto
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
remove unnecessary inclusion of machine specific header files mach/dm646x.h,
mach/hardware.h from vpif.h and aslo mach/dm646x.h from vpif_display.c
driver which comes in the way of platform code consolidation.
Add linux/i2c.h header file in vpif_types.h which is required for
building.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: LMML <linux-media@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was done to resolve a merge and build problem with the
drivers/acpi/processor_driver.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is just a minor update to one titled "imon: Input from ffdc
device type ignored" from Corinna Vinschen. An earlier patch to prevent
an oops when we got early callbacks also has the nasty side-effect of
wedging imon hardware, as we don't acknowledge the urb. Rework the check
slightly here to bypass processing the packet, as the driver isn't yet
fully initialized, but still acknowlege the urb and submit a new rx_urb.
Do this for both interfaces -- irrelevant for ffdc hardware, but
relevant for newer hardware, though newer hardware doesn't spew the
constant stream of data as soon as the hardware is initialized like the
older ffdc devices, so they'd be less likely to trigger this anyway...
Tested with both an ffdc device and an 0042 device.
Reported-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2_CAP_DEVICE_CAPS is valid for the capabilities field only as per
the spec.
Found with v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Control message load increased heavily after CI/CAM support due
to dvb_ca_en50221. It looks like CI/CAM drops to non-working
state easily after error is returned to its callbacks. Due to
that, add some logic to avoid errors repeating failed messages.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As part of the removal of get_driver()/put_driver(), this patch
(as1510) changes driver_find(); it now drops the reference it acquires
before returning. The patch also adjusts all the callers of
driver_find() to remove the now unnecessary calls to put_driver().
In addition, the patch adds a warning to driver_find(): Callers must
make sure the driver they are searching for does not get unloaded
while they are using it. This has always been the case; driver_find()
has never prevented a driver from being unregistered or unloaded.
Hence the patch will not introduce any new bugs. The existing callers
all seem to be okay in this respect, however I don't understand the
video drivers well enough to be certain about them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Kyungmin Park <kyungmin.park@samsung.com>
CC: Andy Walls <awalls@md.metrocast.net>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix bug introduced by multi-frontend to single-frontend change.
It is safer to put DVB-T parts sleeping when auto-switching to DVB-T2
and vice versa. That was original behaviour.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No more error that error seen when device is plugged:
dvb_ca adapter 0: Invalid PC card inserted :(
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bug introduced by multi-frontend to single-frontend change.
This parameter is no longer used after multi-frontend to single-frontend change.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bug introduced by multi-frontend to single-frontend change.
* Add missing DVB-C caps
* Change frontend name as single frontend does all the standards
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As recommended by Jason at ITE, the chip version should select firmware.
However, to continue to support IT9137 firmware with different configuration
the driver will use udev->descriptor.idVendor to select the difference
between IT9135 and IT9137.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If V4L2_CAP_DEVICE_CAPS is set, then the new device_caps field is filled with
the capabilities of the opened device node.
The capabilities field traditionally contains the capabilities of the physical
device, being a superset of all capabilities available at the several device
nodes. E.g., if you open /dev/video0, then if it contains VBI caps then that means
that there is a corresponding vbi node as well. And the capabilities field of
both the video and vbi nodes should contain identical caps.
However, it would be very useful to also have a capabilities field that contains
just the caps for the currently open device, hence the new CAP bit and field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following warning by using platform_driver_probe() instead of
platform_driver_register():
WARNING: drivers/media/video/omap/omap-vout.o(.data+0x24): Section
mismatch in reference from the variable omap_vout_driver to the function
.init.text:omap_vout_probe()
The variable omap_vout_driver references
the function __init omap_vout_probe()
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.3-rc1': (8187 commits)
Linux 3.3-rc1
x86, syscall: Need __ARCH_WANT_SYS_IPC for 32 bits
qnx4: don't leak ->BitMap on late failure exits
qnx4: reduce the insane nesting in qnx4_checkroot()
qnx4: di_fname is an array, for crying out loud...
KEYS: Permit key_serial() to be called with a const key pointer
keys: fix user_defined key sparse messages
ima: fix cred sparse warning
uml: fix compile for x86-64
MPILIB: Add a missing ENOMEM check
tpm: fix (ACPI S3) suspend regression
nvme: fix merge error due to change of 'make_request_fn' fn type
xen: using EXPORT_SYMBOL requires including export.h
gpio: tps65910: Use correct offset for gpio initialization
acpi/apei/einj: Add extensions to EINJ from rev 5.0 of acpi spec
intel_idle: Split up and provide per CPU initialization func
ACPI processor: Remove unneeded variable passed by acpi_processor_hotadd_init V2
tg3: Fix single-vector MSI-X code
openvswitch: Fix multipart datapath dumps.
ipv6: fix per device IP snmp counters
...
USB data transfers may not work if the buffer is allocated at
the stack. Be sure to use kmalloc on all places where a buffer
is needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several changes were needed to make az6007 to work, producing
the same commands as the original driver. This patch does
that.
While here, be less verbose when debug is not enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver were written to use a previous solution for MFE at dvb-usb.
Due to the internal API changes, change the binding to work with the
new way.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code still needs to be commented, as there's a mutex
missing at the az6007_read() call. A mutex there is needed,
in order to prevent RC (or CI) calls while other operations
are in progress.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces no functional changes. It basically defines
a macro for each different req found at the driver, and cleans the
code to use them, making easier to understand the code.
With regards to the IR handling code, although the original code
doesn't define what's the request, it is clear, from the USB logs,
that 0xc5 is for IR polling.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use usb_device for those routines, as it allows using them on
all places. While there, rename to better express the meaning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the ngene/ddbridge firmware into their drivers.
There are two reasons for that:
1) The firmware used there didn't work for a few devices
I tested here (Terratec H5, H6 and H7);
2) At least Terratec H7 doesn't seem to require a firmware
for it to work.
After this change, if firmware is not specified, the driver will
use a rom-based firmware (this seems to be the case for Terratec
H7, although I need to better check the USB dumps to be sure about
that).
In any case, the firmware seems to be optional, as the DRX-K driver
don't return the firmware load error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mutex is there to protect the I2C gate. However, for some reason,
it is being called twice:
[ 2103.542796] usbcore: registered new interface driver dvb_usb_az6007
[ 2103.772392] az6007: drxk_gate_ctrl: enable
[ 2103.793900] az6007: drxk_gate_ctrl: enable
For now, let's just comment, to allow the driver to run.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mt2063 uses a one-byte transfer. This requires a special handling
inside the i2c code. Fix it to properly accept i2c reads. This
is needed to make the mt2063 to be detected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some fixes to allow frontend attachment. The patch is not
complete yet, as just the frontend 0 is initialized. So, more
changes will be needed, including some changes at dvb-usb core.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some changes are needed, in order to make az6007 compile with the
upstream tree. Most of the changes are due to the upstream drxk
module.
Even allowing its compilation, the driver is not working yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Import the az6007 driver from Terratec H7 source, as-is.
It won't compile or run, so latter patches are needed in order
to fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (57 commits)
[media] as3645a: Fix compilation by including slab.h
[media] s5p-fimc: Remove linux/version.h include from fimc-mdevice.c
[media] s5p-mfc: Remove linux/version.h include from s5p_mfc.c
[media] ds3000: using logical && instead of bitwise &
[media] v4l2-ctrls: make control names consistent
[media] DVB: dib0700, add support for Nova-TD LEDs
[media] DVB: dib0700, add corrected Nova-TD frontend_attach
[media] DVB: dib0700, separate stk7070pd initialization
[media] DVB: dib0700, move Nova-TD Stick to a separate set
[media] : add MODULE_FIRMWARE to dib0700
[media] DVB-CORE: remove superfluous DTV_CMDs
[media] s5p-jpeg: adapt to recent videobuf2 changes
[media] s5p-g2d: fixed a bug in controls setting function
[media] s5p-mfc: Fix volatile controls setup
[media] drivers/media/video/s5p-mfc/s5p_mfc.c: adjust double test
[media] drivers/media/video/s5p-fimc/fimc-capture.c: adjust double test
[media] s5p-fimc: Fix incorrect control ID assignment
[media] dvb_frontend: Don't call get_frontend() if idle
[media] DocBook/dvbproperty.xml: Remove DTV_MODULATION from ISDB-T
[media] DocBook/dvbproperty.xml: Fix ISDB-T delivery system parameters
...
The intent here was to test if the FE_HAS_LOCK was set. The current
test is equivalent to "if (status) { ..."
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several control names used inconsistent capitalization or were inconsistent
in other ways. I also corrected a spelling mistake and fixed four strings
that were too long (>31 characters). Harmless, but the string is cut off when
it is returned with QUERYCTRL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an override of read_status to intercept lock status. This allows
us to switch LEDs appropriately on and off with signal un/locked.
The second phase is to override sleep to properly turn off both.
This is a hackish way to achieve that.
Thanks to Mike Krufky for his help.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This means cut & paste from the former f. attach. But while at it write
to the right GPIO to turn on the right LED. Also turn the other two
off jsut for sure.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The start is common for both stk7070pd and novatd specific routine.
This is just a preparation for the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To properly support the three LEDs which are on the stick, we need
a special handling in the ->frontend_attach function. Thus let's have
a separate ->frontend_attach instead of ifs in the common one.
The hadnling itself will be added in further patches.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dib0700 needs a binary firmware file. This patch added the MODULE_FIRMWARE-macro.
Signed-off-by: Christoph Anton Mitterer <calestyo@scientia.net>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This small patch removes superfluous DTV_CMDs from dvb_frontend.c which were added in the initially when ISBD-T support was added.
They were there unnoticed even though compilers should have warning about those duplicates. Finally they did and now we can remove them.
Thanks to Dan Carpenter <dan.carpenter@oracle.com> for pointing that out.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
queue_setup callback has been extended with struct v4l2_format *fmt
parameter in 2d86401c2c commit. This patch adds this parameter to
s5p-jpeg driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite a duplicated test to test the correct value
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite a duplicated test to test the correct value
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the mismatch between control IDs (CID) and controls
for hflip, vflip and rotate.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sascha Hauer