Pre-allocate a skb at init time to be used for control messages to the HW
if skb allocation fails.
Tolerate failures to send messages initializing some memories at the cost of
parity error detection for these memories.
Retry sending connection id release messages if both alloc_skb(GFP_ATOMIC)
and alloc_skb(GFP_KERNEL) fail.
Do not bring the interface up if messages binding queue set to port fail to
be sent.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the AEL2020 phy.
Add PCI IDs of the boards using this phy.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not call t3_link_fault() under spinlock, as it calls msleep().
Besides, only the access to pi->link_fault needs to be serialized.
Also initialize local variables before checking the link status,
link state fields might otherwise end up containing garbage.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH attempts to recover up 6 times.
The last attempt leaves all the ports and adapter down.hen
The driver is then unloaded, bringing the adapter down again
unconditionally. The unload will hang.
Check if the adapter is already down before trying to bring it down again.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fatal error task can be scheduled while processing an offload packet
in NAPI context when the connection handle is bogus. this can race
with the ports being brought down and the cxgb3 workqueue being flushed.
Stop napi processing before flushing the work queue.
The ULP drivers (iSCSI, iWARP) might also schedule a task on keventd_wk
while releasing a connection handle (cxgb3_offload.c::cxgb3_queue_tid_release()).
The driver however does not flush any work on keventd_wq while being unloaded.
This patch also fixes this.
Also call cancel_delayed_work_sync in place of the the deprecated
cancel_rearming_delayed_workqueue.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the existing periodic task to handle link faults.
The link fault interrupt handler is also called in work queue context,
which is wrong and might cause potential deadlocks.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use resource_size_t to declare mmio start and len variables.
Print PEX error register after EEH resumed.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start queue set reclaim timers after the queue sets have been
allocated successfully.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently ignores the local or remote link faults
raised at the mac layer. This patch fixes it.
Our mac however only advertizes link events, so wait for the
phy to stabilize the link, then enable mac link events interrupts.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under RX pressure, The HW might generate a high load of interrupts
to signal mac fifo or free lists overflow.
Disable the interrupts, and poll the relevant status bits
to maintain stats.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for adapters with a PCI id equal to 0x35.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Move variable declaration as close to usage as possible.
Fix this sparse warning:
drivers/net/cxgb3/cxgb3_main.c:1586:21: warning: symbol 'cap' shadows an earlier one
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set up a notification mechanism to inform upper layer modules
(iWARP, iSCSI) of a chip reset due to an EEH event or a fatal error.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes cxgb3 invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
I've kept the ioctl controls for per-queue LRO switches. However,
we should not encourage anyone to use these.
Because of that, I've also kept the skb construction code in
cxgb3. Hopefully we can phase out those per-queue switches
and then kill this too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently drops to line interrupt mode
if it did not get all the msi-x vectors it requested.
Allow msi-x settings when a minimal amount of vectors
is provided.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a system with a Chelsio adapter (driven by cxgb3) whose ports are
part of a Linux bridge. Recently I updated the kernel and discovered
that things stopped working because cxgb3 was doing LRO on packets that
were passed into the bridge code for forwarding. (Incidentally, this
problem manifested itself in a strange way that made debugging a bit
interesting -- for some reason, the skb_warn_if_lro() check in bridge
didn't trigger and these LROed packets were forwarded out a forcedeth
interface, and caused the forcedeth transmit path to get stuck)
This is because cxgb3 has no way of keeping state for the LRO flag until
the interface is brought up, so if the bridging code disables LRO while
the interface is down, then cxgb3_up() will just reenable LRO, and on my
Debian system at least, the init scripts add interfaces to a bridge
before bringing the interfaces up.
Fix this by keeping track of each interface's LRO state in cxgb3 so that
when bridge disables LRO, it stays disabled in cxgb3_up() when the
interface is brought up. I did this by changing the rx_csum_offload
flag into a pair of bit flags; the effect of this on the rx_eth() fast
path is miniscule enough that it should be fine (eg on x86, a cmpb
instruction becomes a testb instruction).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NIC driver can work with mutliple versions of the FW.
Let the driver load when the embedded FW does not match,
and the FW update mechanism failed.
The iWARP module will make its own loading decision.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement NIC Tx multiqueue.
Bump up driver version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update FW loading path to accomodate in-kernel images location
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix t3_eth_xmit() missing into the netdev_ops structure.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to network device ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the iw_cxgb3 module's cxgb3_client "add" func gets called by the
cxgb3 module, the iwarp driver ends up calling the ethtool ops get_drvinfo
function in cxgb3 to get the fw version and other info. Currently the
iwarp driver grabs the rtnl lock around this down call to serialize.
As of 2.6.27 or so, things changed such that the rtnl lock is held around
the call to the netdev driver open function. Also the cxgb3_client "add"
function doesn't get called if the device is down.
So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the device,
the iw_cxgb3 add func gets called with the rtnl_lock held. If you
load cxgb3, ifconfig up the device, then load iw_cxgb3, the add func
gets called without the rtnl_lock held. The former causes the deadlock,
the latter does not.
In addition, there are iw_cxgb3 sysfs handlers that also can call
down into cxgb3 to gather the fw and hw versions. These can be called
concurrently on different processors and at any time. Thus we need to
push this serialization down in the cxgb3 driver get_drvinfo func.
The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement ethtool's get_flags and set_flags methods.
It enables ethtool to control the LRO settings.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for SR PHY.
Auto-detect phy module type, and report type changes.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic code to manage interrupt driven PHYs.
Do not reset the phy after link parameters update,
the new values might get lost.
Return early from link change notification
when the link parameters remain unchanged.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second step in overall phy layer reorganization.
Clean up the port_type_info structure.
Support coextistence of clause 22 and clause 45 MDIO devices.
Select the type of MDIO transaction on a per transaction basis.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a queue set per core, up to the maximum of available qsets.
Share the queue sets on multi port adapters.
Rename MSI-X interrupt vectors ethX-N, N being the queue set number.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when a fatal error occurs, bring ports down, reset the chip,
and bring ports back up.
Factorize code used for both EEH and fatal error recovery.
Fix timer usage when bringing up/resetting sge queue sets.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A SGE queue set timer might access registers while in EEH recovery,
triggering an EEH error loop. Stop all timers early in EEH process.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the chip when the PCI link goes down.
Preserve the napi structure when a sge qset's resources are freed.
Replay only HW initialization when the chip comes out of reset.
Signed-off-by: Divy Le ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix faiures path when ports are stopped and restarted
in EEH recovery.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Otherwise theoretically at least
CAP_NET_ADMIN
Reload new firmware
Wait..
Firmware patches kernel
So it should be CAY_SYS_RAWIO - not that I suspect this is in fact a
credible attack vector!
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the warning:
drivers/net/cxgb3/cxgb3_main.c: In function ‘offload_open’:
drivers/net/cxgb3/cxgb3_main.c:936: warning: ignoring return value of
‘sysfs_create_group’, declared with attribute warn_unused_result
Now the return value is checked; if sysfs_create_group() returns failure,
a warning is printed using dev_dbg, and the code continues as before. Use
of dev_dbg ensures printk is not needlessly included unless desired for
debugging.
Signed-off-by: Dan Noe <dpn@isomerica.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
set_pci_drvdata() stores a pointer to the adapter,
not the net device.
Add missing softirq blocking in t3_mgmt_tx.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>