The PCIe driver has been fully clock aware for quite a while. Remove
the kexec code to enable the PCIe clock, since the PCIe driver will do
the right thing.
jac adds:
[arnd]: fixes a build error when KEXEC is enabled and KIRKWOOD_LEGACY is not
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instantiate the L2 cache from DT. Indicate in DT where the cache
control register is so that it is possible to enable/disable write
through on the CPU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the gradual move to DT, kirkwood has become a lot less dependent
on plat-orion. cache-feroceon-l2.h is the last dependency. Move it out
so we can drop plat-orion when building DT only kirkwood boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the move to mach-mvebu and MULTI_V5, the global iomap for all
registers will be going away. So explicitly map the CPU configuration
register before using it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to be able to move DT support into mach-mvebu, the DT code
needs to be cleanly separated from common and pcie code. Import the
needed bits of these files into board-dt.c. The "common" code then
becomes purely legacy, supporting non-DT boards, so reflect this in
the Makefile targets.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This will be added back using the mach-mvebu equivalent once the move
has been made.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The mv88f6281gtw_ge has a ethernet switch connected to the ethernet
port of the SoC. Convert the platform device instantiation to a DT
instantiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: florian@openwrt.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The pm code needs to be separated from common.h in order to split DT
and non-DT systems apart. Move the declarations into a header file of
its own and include it where needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> (on kirkwood)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit 2326f04321 (ARM: kirkwood: convert to DT irqchip and clocksource)
dropped the call to kirkwood_timer_init() when booting with DT.
This results in kirkwood_tclk not being set and the boot message is now:
Kirkwood: MV88F6281-A0, TCLK=0
This patch modifies the message for printing only the kirkwood id,
as it allows to detect if we're running A0/A1/... variants with a simple
dmesg.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With legacy devices converted to DT and a proper ethernet MAC
workaround, we can now remove the clk workarounds for legacy
devices. While at it, also cleanup the list of includes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
Merging in dt clock cleanup as a pre-req with some of the later SoC branches.
There are a handful of conflicts here -- some of the already merged SoC
branches should have been based on the cleanup but weren't.
In particular, a remove/add of include on highbank and two remove/remove
conflicts on kirkwood were fixed up.
* cleanup/dt-clock: (28 commits)
ARM: vt8500: remove custom .init_time hook
ARM: vexpress: remove custom .init_time hook
ARM: tegra: remove custom .init_time hook
ARM: sunxi: remove custom .init_time hook
ARM: sti: remove custom .init_time hook
ARM: socfpga: remove custom .init_time hook
ARM: rockchip: remove custom .init_time hook
ARM: prima2: remove custom .init_time hook
ARM: nspire: remove custom .init_time hook
ARM: nomadik: remove custom .init_time hook
ARM: mxs: remove custom .init_time hook
ARM: kirkwood: remove custom .init_time hook
ARM: imx: remove custom .init_time hook
ARM: highbank: remove custom .init_time hook
ARM: exynos: remove custom .init_time hook
ARM: dove: remove custom .init_time hook
ARM: bcm2835: remove custom .init_time hook
ARM: bcm: provide common arch init for DT clocks
ARM: call of_clk_init from default time_init handler
ARM: vt8500: prepare for arch-wide .init_time callback
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Ethernet IP on Kirkwood SoCs loose their MAC address register content
if clock gated. To allow modular ethernet driver setups and gated clocks
also on non-DT capable bootloaders, we fixup port device nodes with no
valid MAC address property. This patch copies MAC address register
contents set up by bootloaders early, notably before ethernet clocks
are gated. While at it, also reorder call sequence in _dt_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since the PCIe devices is properly initialized from the DT, the clocks
are now referenced in the device tree nodes, and it's not needed
to have this hack to add them explicitly.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since the MBus is initialized from the DT, it's not necessary to
call the legacy initialization.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Implements standby support for Kirkwood SoC. When the SoC enters
standby state the memory PM units are disabled, the DDR is set
in self-refresh mode, and the CPU is set in WFI.
At this point there's no clock gating, as that is considered each
driver's task.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
kirkwood_setup_wins is the last manual caller of mbus in kirkwood, don't
call it for DT boards and rely on the DT having a mbus node with
a proper ranges property to setup these windows.
Move all the mbus ranges properties for all boards into kirkwood.dtsi,
since they are currently all the same.
This makes the DT self consistent, since the physical address of the
NAND and CRYPTO are both referenced internally. The arbitary Linux
constants KIRKWOOD_NAND_MEM_PHYS_BASE and KIRKWOOD_SRAM_PHYS_BASE
no longer have to match the DT values.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With arch/arm calling of_clk_init(NULL) from time_init(), we can now
remove custom .init_time hooks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Board updates for 3.12. Again, a bit of domain overlap with SoC and DT branches,
but most of this is around legacy code and board support. We've found that
platform maintainers have a hard time separating all of these out and might
move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and clocksource
setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas Lager.
- New backlight drivers for backlights used on Renesas shmobile platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for others in
the same mach directory. More in 2.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSKhrfAAoJEIwa5zzehBx3OOAQAJCWhoYaHvWmyAf+xCOQNpX2
YgAngENW04VpHFOyn6BtoGv6+5JypdB2TmK3GHHlVJd1Im5mD1wgm8hAfgyV8lQ4
UeJULdA2HZAstKeTirO65BIyUb5QIrWakF24ccfIfg2xeScM8FV0m8cmzeo3fYAf
DmmeoSCmvTdu/cDWBNlsQZ/as8qCQwyF+5kZg+SMl1btA1Publu2I5lDE02TH46d
sc5mN+ihw0JG62EJV7pov6uVyeFLExoTbrNfQZ4rixmKkMDS/jq5ZbBS5c0i8ULF
s1UMSZtYTcUO9rAPv3+MOIc7fq7nKo9lLuwMrA1HHUEDJ2BEi8DIp99F+ZYm/MSL
WpVxYNwOobPcMJBYGR2fy4GgpIyWB285GgrBUxcq7t0Xi4uBbptwjLhDE4d7LREV
8guW251R+OEVPYcwFctsubnox0MViyC3CQ1FaAAdtTjpSKomlhk/yaxaQ9nGrxls
QCZgXHWm4Ir3QYv8XfOn0X9vdP81EnX11SiwtrRSJ71QMs814nB8NdPDqU4VHsw8
exKmqjq/Lt+F9Kpxn/FevNNuYOdefZNQi00yl3ERchdIGdvRwE/0yA0D69mpwIVr
E41UwvH3g43vazCo2PMdWPWuFlpGMR3iZ4pXnDLH/w33ppfJWfokYwKSRQ/mu/MN
LMjkwoZn1X+fZzNSh9/G
=EGua
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
No platform code left now, so remove all references to it.
The reset gpio code didn't work to begin with, it will be replaced with
a DT node at a future date. -jc
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit converts the mv88f6281gtw_ge Kirkwood board to use a
Device Tree representation, except for the Ethernet devices and the
DSA switch. Even though the mv643xx_eth driver has a DT binding,
converting this board to use it is for now left on the side because it
doesn't use a simple PHY, but a DSA switch instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit replaces the legacy MBus initialization with the new
DT-based in Kirkwood. For boards that are not yet converted to DT,
we keep the legacy initialization.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Kirkwood DT boards have been converted to DT SDIO already, we can now
remove the legacy clock gate workaround for SDIO clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With recent support for true irqchip and clocksource drivers for Orion
SoCs, now make use of it on DT enabled Kirkwood boards.
This also introduces a new Kconfig option for legacy (non-DT) Kirkwood
where old code is moved out to and polishes DT board file a little bit.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With all boards converted to DT enabled mv643xx_eth we can now
remove the clock alias for gbe clocks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With DT support for mv643xx_eth board specific init for some boards now
is unneccessary. Remove those board files, Kconfig entries, and
corresponding entries in kirkwood_defconfig.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
These are 18 branches on 9 platforms with board specific changes, mostly
for defconfig files, but nothing really exciting in here.
Since the shmobile platform still uses board files for some of the newer
machines, we get a few changes there as the result of drivers getting
enabled for those boards. This causes some conflicts with contents getting
added from multiple branches in sh-mobile specific files. Renesas is
putting a lot of work into migrating to device-tree based setup, which
will make all those files obsolete in the future and avoid both the
conflicts and the need to have these files in the first place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7bgc
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board specific changes from Arnd Bergmann:
"These are 18 branches on 9 platforms with board specific changes,
mostly for defconfig files, but nothing really exciting in here.
Since the shmobile platform still uses board files for some of the
newer machines, we get a few changes there as the result of drivers
getting enabled for those boards. This causes some conflicts with
contents getting added from multiple branches in sh-mobile specific
files. Renesas is putting a lot of work into migrating to device-tree
based setup, which will make all those files obsolete in the future
and avoid both the conflicts and the need to have these files in the
first place."
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
arm: multi_v7_defconfig: Enable initrd/initramfs support
arm: multi_v7_defconfig: Enable Zynq UART driver
ARM: omap2plus_defconfig: enable USB_PHY and NOP_USB_XCEIV
ARM: OMAP1: nokia770: enable Tahvo
ARM: OMAP3EVM: Marking omap3_evm_display_init() with CONFIG_BROKEN
arm: omap: board-overo: reset GPIO for SMSC911x
ARM: shmobile: BOCK-W: change Ether device name
ARM: ux500: board-mop500: remove unused pin modes
ARM: shmobile: bockw: add MMCIF support
ARM: shmobile: bockw: add SPI FLASH support
ARM: shmobile: bockw: add I2C device support
ARM: shmobile: BOCK-W: add Ether support
ARM: tegra: defconfig updates
ARM: shmobile: bockw defconfig: add MMCIF support
ARM: shmobile: bockw defconfig: add M25P80 support
ARM: shmobile: bockw defconfig: add RTC RX8581 support
ARM: shmobile: marzen: keep local function as static
ARM: shmobile: bockw: add SDHI0 support
ARM: shmobile: marzen: Use INTC External IRQ pin driver for SMSC
ARM: shmobile: lager: support GPIO switches
...
- clk: mvebu
- reorganize by SoC to remove built up #ifdefs
- add clk flags per clock gate
Note: this branch only depends on mvebu/pcie in order to prevent managing a
tricky modify/remove file merge conflict. By rebasing on mvebu/pcie, we are
able to build the resolution into the patch series. The change is small, and
has been tested by the respective authors.
depends:
- mvebu/pcie
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRplb0AAoJEAi3KVZQDZAefTAH/1PMcXV+N/9HUgmx9XNpWg7Z
3ODWrA7Ewdvq9hfv9t+EH0FIdrZRA400p+AJuWSUuLzS7NzmCMTk/Pzad/W36ZY2
+8yJXVThSHqEQN/Vi1FtZGTKqRXZX/udVH5oNFV9jrUEFvLwuI/6/hCdkzlFKEol
9YJHNUyiul9P0jpcDXSSTFCpNXUPgQPuGTtIip0TKFmZOdA2QglgQAVkIwACZ+uX
PA7ewiFj1yfOhv8eh+nnb5kAsJEj1ynfMJywn7P/OC6ugAJtE9D0ZpzlYuj3lFEo
Z2snnzU7wVARfp1i6x3kNUyBiGHnJfxJC1KMePj87XP80BVzX1rmCoFY6x9nutg=
=jIi7
-----END PGP SIGNATURE-----
Merge tag 'seb_clk-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu clock restructuring for v3.11
- clk: mvebu
- reorganize by SoC to remove built up #ifdefs
- add clk flags per clock gate
* tag 'seb_clk-3.11' of git://git.infradead.org/users/jcooper/linux:
clk: mvebu: disintegrate obsolete file
ARM: mvebu: move DT boards to SoC-centric clock init
ARM: kirkwood: move DT boards to SoC-centric clock init
ARM: dove: move DT boards to SoC-centric clock init
clk: mvebu: add Armada XP SoC-centric clock init
clk: mvebu: add Armada 370 SoC-centric clock init
clk: mvebu: add Kirkwood SoC-centric clock init
clk: mvebu: add Dove SoC-centric clock init
clk: mvebu: add common clock functions for core clk and clk gating
clk: mvebu: introduce per-clock-gate flags
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpP1WAAoJEAi3KVZQDZAeItIH/1QVHhqYSpOnXGu4zQHswvIM
SRQoy4hiCJm+yywTnIDJPMQdBKD1vURRRdGWQouNsFoBaHki4v2BBxfBNFoDN+rx
VtECH7F1SbJ/Pb7XLVnswqRXVNqrY5fOY5mW42ALFBT9VxcKoD1FyqCaXfaU9JA4
VQCzR7DjFhr8bppZknQ5ZT/qI66Wj1oNiJtBdItmxT0pVfElvAOV6FHzfMGrrDrM
+v8T8KdFIdmH1Ny5J5KLQSE9qBLqae0vlDNgsfwfh1DY/Lye3rDHqPDKrh7YZjHR
xNc6JU+zEdP3tK1f1jgmjn/giY7HqpAFm46p9k/pF9gsE5SE0L/e0Dh9apOcq24=
=qUyf
-----END PGP SIGNATURE-----
Merge tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu pcie driver (kirkwood) for v3.11
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: convert db-88f6281/db-88f6282 to the Device Tree
arm: kirkwood: convert QNAP TS219 to use DT for the PCIe interface
arm: kirkwood: convert ZyXEL NSA310 to use DT for the PCIe interface
arm: kirkwood: convert MPL CEC4 to use DT for the PCIe interface
arm: kirkwood: convert Iomega Iconnect to use DT for the PCIe interface
arm: kirkwood: add SoC-level Device Tree data for PCIe interfaces
arm: kirkwood: move PCIe window init to legacy driver
pci: mvebu: enable driver usage on Kirkwood
Register a platform driver structure for the cpufreq driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SoC centric clock init for Kirkwood can be used by calling of_clk_init.
Use it and get rid of mvebu_clocks_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit converts the Marvell DB-88F6281/DB-88F6282 board to the
Device Tree. In fact, the code was supporting two different boards:
one with the 6281 SoC variant, and one with the 6282 SoC variant. The
difference between the two being that the 6281 has one PCIe interface,
and the 6282 has two PCIe interfaces.
In order to handle that with the Device Tree, we create a
'kirkwood-db.dtsi' file that contains the definitions common to both
boards, and 'kirkwood-db-88f6281.dts' and 'kirkwood-db-88f6282.dts'
for the definitions specific to each board. This is similar to what is
done for the QNAP TS219 Kirkwood platform.
We have kept one single Kconfig option, just like it was before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
mach-kirkwood/board-dt.c defines its own OF matching table, but in
fact, it is the same to the default of_default_bus_match_table[] which
is already used by mach-mvebu, mach-dove and mach-orion5x.
This patch therefore makes mach-kirkwood use the same default OF
matching table.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is the third and smallest of the SoC specific updates.
Changes include:
* SMP support for the Xilinx zynq platform
* Smaller imx changes
* LPAE support for mvebu
* Moving the orion5x, kirkwood, dove and mvebu platforms
to a common "mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus"
driver. Since this is used on multiple platforms may potentially
get shared with other architectures (powerpc and arm64), it
was moved to drivers/bus/. We expect other similar drivers to
get moved to the same place in order to avoid creating more
top-level directories under drivers/ or cluttering up the
messy drivers/misc/ even more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rQsu
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
"This is the third and smallest of the SoC specific updates. Changes
include:
- SMP support for the Xilinx zynq platform
- Smaller imx changes
- LPAE support for mvebu
- Moving the orion5x, kirkwood, dove and mvebu platforms to a common
"mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus" driver.
Since this is used on multiple platforms may potentially get shared
with other architectures (powerpc and arm64), it was moved to
drivers/bus/. We expect other similar drivers to get moved to the
same place in order to avoid creating more top-level directories under
drivers/ or cluttering up the messy drivers/misc/ even more."
* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: imx: reset_controller may be disabled
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
...
This commit migrates the mach-kirkwood platforms to use the mvebu-mbus
driver and therefore removes the Kirkwood-specific addr-map code.
The kirkwood_init_early() function is now responsible for initializing
the mvebu-mbus driver by calling mvebu_mbus_init().
The address decoding windows are now registered in the
kirkwood_setup_wins() function. It is worth noting that the four PCIe
address decoding windows will ultimately no longer have to be
registered here: it will be done automatically by the PCIe driver once
Kirkwood has been migrated to use the upcoming mvebu PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for the LaCie NAS CloudBox. The CloudBox
is a low cost NAS based on the Network Space v2.
Chipset list:
- CPU MARVELL 88F6702 1Ghz
- SDRAM memory: 256MB DDR2-800 (2x128MB x8) 400Mhz
- 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
- SPI flash, NOR 512KB
- 1 push button
- 2 LEDs (red and blue)
There is no EEPROM and no USB ports embedded.
Note that this board must not be confused with the Network Space Mini v2
which is embedded in a previous LaCie product also named CloudBox.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for NETGEAR ReadyNAS Duo v2 (Hardware specs available
here: http://natisbad.org/NAS/). Almost everything is supported via
provided .dts. A board-readynas.c file is nonetheless required for
device not only converted to DT (Gbit controller).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Tested-By: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ethernet controller used on kirkwood looses its MAC address
register contents when the corresponding clock is gated. As soon as
mv643xx_eth is built as module, the clock gets gated and when loading
the module, the MAC address is gone.
Proper DT support for the mv643xx_eth driver is expected soon, so we add
a workaround to always enable ge0/ge1 clocks on kirkwood. This workaround
is also already used on non-DT kirkwood kernels.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add a device tree entry for the Guruplug Server Plus board. This port
was based both on the work done on the dreamplug and the dockstar.
It builds, boots and works on my Guruplug Server Plus.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that SDIO is instantiated via DT, and the SDIO DT node has a clocks
property, we no longer need a C coded clock alias. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that USB is instantiated via DT, and the USB DT node has a clocks
property, we no longer need a C coded clock alias. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Move the Kirkwood cpuidle driver out of arch/arm/mach-kirkwood and
into drivers/cpuidle. Convert the driver into a platform driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We moved to declaring clk gates in DT. However, device which do not
yet have a DT binding need to have a clkdev alias. This was missing
for SDIO.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mplch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is a branch with updates for Marvell's mvebu/kirkwood platforms. They
came in late-ish, and were heavily interdependent such that it didn't
make sense to split them up across the cross-platform topic branches. So
here they are (for the second release in a row) in a branch on their own.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7luC
-----END PGP SIGNATURE-----
Merge tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=sgYz
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals,
etc."
Fix up conflicts mostly as per Olof.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
ARM: S3C64XX: Add dummy supplies for Glenfarclas LDOs
ARM: S3C64XX: Add registration of WM2200 Bells device on Cragganmore
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
ARM: mmp: select pinctrl driver
...
Add support for Plat'Home OpenBlocks A6 using the device tree
where possible.
This commit supports SATA, USB, ether and serial console.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn