We in the pre_enable hook we should only rely on the pipe config and
not on some other state set through properties or detect functions.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also add state readout and cross-check support. The only invasive change
is wiring up the new flag to the ->set_infoframes callbacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For compliance we really should be sending NULL infoframes always
when we detect a hdmi capable monitor. Also remove the now redudant
setting for the has_audio case and enforce that audio is only
possible with a hdmi sink.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Everything should be in place so enable rc6/rps for bdw.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
by correctly displaying result and requested.
Suggested-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In BDW, Apart from unmasking up/down threshold interrupts. we need
to umask bit 32 of PM_INTRMASK to route interrupts to target via Display
Interface.
v2: Add (1<<31) mask (Ville)
v3: Add Gen check for the mask (ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Almost all of it is reusable from the existing code. The primary
difference is we need to do even less in the interrupt handler, since
interrupts are not shared in the same way.
The patch is mostly a copy-paste of the existing snb+ code, with updates
to the relevant parts requiring changes to the interrupt handling. As
such it /should/ be relatively trivial. It's highly likely that I missed
some places where I need a gen8 version of the PM interrupts, but it has
become invisible to me by now.
This patch could probably be split into adding the new functions,
followed by actually handling the interrupts. Since the code is
currently disabled (and broken) I think the patch stands better by
itself.
v2: Move the commit about not touching the ringbuffer interrupt to the
snb_* function where it belongs (Rodrigo)
v3: Rebased on Paulo's runtime PM changes
v4: Not well validated, but rebase on
commit 730488b2ed
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 7 20:12:32 2014 -0300
drm/i915: kill dev_priv->pm.regsave
v5: Rebased on latest code base. (Deepak)
v6: Remove conflict markers, Unnecessary empty line and use right
IIR interrupt (Ville)
v7: mask modified without rmw (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we dont have semaphores enabled, we allocate 4
dwords for signalling. But end up emitting more regardless.
Fix this by bailing out early if semaphores are not enabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78274
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78283
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added as generic parameters which will be initialized in the panel
driver and are specific to panels.
Backlight delays have also kept as placeholders and will be used used
once we have MIPI backlight enabling support
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In VBT fields operation mode is 0 for Video mode and 1 for command mode.
This field will be directly used as is in generic panel driver. So
adjust accordingly.
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are generated with intel-gpu-tools/tools/null_state_gen
v2: Don't use header file for states (Daniel Vetter)
v3: Proper URB state size for gen8/GT3 (Damien Lespiau)
Tested-by: Kristen Carlson Accardi <kristen@linux.intel.com> (v1)
Tested-by: Oscar Mateo <oscar.mateo@intel.com> (v2)
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HW guys say that it is not a cool idea to let device
go into rc6 without proper 3d pipeline state.
For each new uninitialized context, generate a
valid null render state to be run on context
creation.
This patch introduces a skeleton with empty states.
v2: - No need to vmap (Chris Wilson)
- use .c files for state (Daniel Vetter)
- no need to flush as i915_add_request does it
- remove parameter for batch alloc size
- don't wait for the init (Ben Widawsky)
v3: - move to cpu/gpu (Chris Wilson)
Tested-by: Kristen Carlson Accardi <kristen@linux.intel.com> (v1)
Tested-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we end up tearing down fences when e.g. the client quits
way too early. Might or might not fix a fence pin_count BUG Ville has
reported.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Userspace can currently provoke this when e.g. trying to use a pinned
scanout as a cursor or overlay target. Later on that might lead to
some fun fence pin count mayhem.
Spurred by Ville's report that something goes wrong here and
originally I've thought that this might slip through the pwrite gtt
fastpath. But that one checks of obj tiling, so should be ok.
But one thing that _does_ blow up is the vma unbinding with more than
one address space. The next patch will fix this.
v2: Use a WARN_ON - Chris pointed out that we already catch all cases
so userspace can't provoke this like I've originally feared.
While reviewing relevant code I've noticed a pile of DRM_ERROR in the
overlay&cursor code which are all triggerable by userspace. Tune them
down while at it.
v3: Split out the DRM_ERROR->DRM_DEBUG_KMS change into a separate patch,
as requested by Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During initial probing of the modes to assign to the fbdev console, we
use the CRTC and connector ids. These are much harder for us to
understand than if we used their actual names (or pipe in the CRTC
case). Similarly, we want to manually print the mode size rather than
rely on mode->name being set.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Patch done using the following semantic patch (thanks Daniel for the
help!)
@@
iterator name list_for_each_entry;
iterator name for_each_crtc;
struct drm_crtc * crtc;
struct drm_device * dev;
@@
-list_for_each_entry(crtc,&dev->mode_config.crtc_list, head) {
+for_each_crtc(dev,crtc) {
...
}
Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Generated using the semantic patch:
@@
iterator name list_for_each_entry;
iterator name for_each_intel_crtc;
struct intel_crtc * crtc;
struct drm_device * dev;
@@
-list_for_each_entry(crtc,&dev->mode_config.crtc_list,...) {
+for_each_intel_crtc(dev,crtc) {
...
}
Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fed up with having that long list_for_each_entry() invocation?
Use for_each_intel_crtc()!
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Squash in patch that exported ilk_wm_max_level.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That's not necessary and makes the code not as neat as it could be.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow UXA submits a completely bogus DR4 value since essentially
forever. It was originally introduced in
commit bade7d7d2505a10a8a7d24b084aff9742e2d6d64
Author: Eric Anholt <eric@anholt.net>
Date: Fri Jun 6 14:03:25 2008 -0700
Use the DRM for submitting batchbuffers when available.
and dutifully copied around ever since. Since we want to keep the
general dirt catching around just special case the UXA value.
This regression was introduced in
commit 9cb346648d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Apr 24 08:09:11 2014 +0200
drm/i915: Catch dirt in unused execbuffer fields
Comment from Chris' review:
"To be fair, it is a sensible value if one supposes a Region style API to
cliprects. Under that API, DR[14] define the extents of the clip region,
and ((0,0), (0,0)) [DR1==DR4==0] would mean all clipped, do not draw
anything."
v2: Pimp commit message a bit and remove the double space.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78494
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jörg Otte <jrg.otte@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The fence pin count should always be <= the bo pin count. If that's
not the case then we have a funny problem and are leaking references
somewhere.
Which means we can catch fence pin leaks by checking for the same
upper limit as we do for the bo pin count. Inspired by a discussion
with Ville about a fence leak igt testcase.
v2: Also check for fence->pin_count <= ggtt_vma->pin_count, since that
might catch a leak even quicker. Also de-inline them, they're getting
too big.
v3: Don't separately check for MAX_PIN_COUNT since the > vma->pin_count
check will catch that already (Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe might not start to actually run until the port has been enabled
(depends on the platform and port type). So don't try to wait for vblank
after we enabled the pipe but haven't yet enabled the port.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already moved the plane disable/enable to happen as the first/last
thing on every other platforms. Follow suit with gmch platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Frob drm_vblank_on conflict, as usual.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is missing in:
commit 78325f2d27
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Tue Apr 29 14:52:29 2014 -0700
drm/i915: Virtualize the ringbuffer signal func
Looks to me like a rebase side-effect...
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV uses the same bits as SNB/VLV to code the Graphics Mode Select field
(GFX stolen memory size) with the addition of finer granularity modes:
4MB increments from 0x11 (8MB) to 0x1d.
Values strictly above 0x1d are either reserved or not supported.
v2: 4MB increments, not 8MB. 32MB has been omitted from the list of new
values (Ville Syrjälä)
v3: Also correctly interpret GGMS (GTT Graphics Memory Size) (Ville
Syrjälä)
v4: Don't assign a value that needs 20bits or more to a u16 (Rafael
Barbalho)
[vsyrjala: v5: Split the early quirks to another patch]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Tested-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No CRT output on CHV, so don't call intel_crt_init().
v2: Don't disable CRT on HAS.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add chv_crtc_clock_get() to read out the DPLL settings.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Fix compile due to bikeshedded headers in an earlier patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming phy layer for CHV based on "Application note for 1273
CHV Display phy".
v2: Rebase the code and do some cleanup.
v3: Rework based on Ville review.
-Fix the macro where the ch info need to swap, and add parens to ?
operator.
-Fix wrong bit define for DPIO_PCS_SWING_CALC_0 and
DPIO_PCS_SWING_CALC_1 and rename for meaningful.
-Add some comments for CHV specific DPIO registers.
-Change the dp margin registery value to decimal to align with the
doc.
-Fix the not clearing some value in vlv_dpio_read before write again.
-Create new hdmi/dp encoder function for chv instead of share with
valleyview.
v4: Rebase the code after rename the DPIO registers define and upstream
change.
Based on Ville review.
-For unique transition scale selection, after Ville point out, look
like the doc might wrong for the bit 26. Use bit 27 for ch0 and
ch1.
-Break up some dpio write value into two/three steps for readability.
-Remove unrelated change.
-Add some shift define for some registers instead just give the hex
value.
-Fix a bug where write to wrong VLV_TX_DW3.
v5: Based on Ville review.
- Move tx lane latency optimal setting from chv_dp_pre_pll_enable to
chv_pre_enable_dp, and chv_hdmi_pre_pll_enable to
chv_hdmi_pre_enable respectively.
- Fix typo in one margin_reg_value for DP_TRAIN_VOLTAGE_SWING_400.
- Clear DPIO_TX_UNIQ_TRANS_SCALE_EN for DP and HDMI.
- Mask the old deemph and swing bits for hdmi.
v6: Remove stub for pre_pll_enable for dp and hdmi.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[vsyrjala: Don't touch panel power sequencing on DP]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming PLL for CHV based on "Application note for 1273 CHV
Display phy".
v2: -Break the common lane reset into another patch.
-Break the clock calculation into another patch.
-The changes are based on Ville review.
-Rework based on DPIO register define naming convention change.
-Break the dpio write into few lines to improve readability.
-Correct the udelay during chv_enable_pll.
-clean up some magic numbers with some new define.
-program the afc recal bit which was missed.
v3: Based on Ville review
- minor correction of the bit defination
- add deassert/propagate data lane reset
v4: Corrected the udelay between dclkp enable and pll enable.
Minor comment and better way to clear the TX lane reset.
v5: Squash in fixup from Rafael Barbalho.
[vsyrjala: v6: Polish the defines (Imre)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the chv clock limit, find the best divisor.
The divisor data has been verified with this spreadsheet.
P1273_DPLL_Programming Spreadsheet.
v2: Rebase the code and change the chv_find_best_dpll based on new
standard way to use intel_PLL_is_valid. Besides, clean up some extra
variables.
v3: Ville suggest better fixed point for m2 calculation.
v4: -Add comment for the limit is compute using fast clock. (Ville)
-Don't pass the request clock to chv_clock, as the same function will
be use clock readout, which doens't have request clock. (Ville)
-Add and use DIV_ROUND_CLOSEST_ULL to consistent with other clock
calculation. (Ville)
-Fix the dp m2 after m2 has stored fixed point. (Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Avoid div-by-zero in chv_clock()]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During cold boot, the display controller needs to deassert the common
lane reset. Only do it once during intel_init_dpio for both PHYx2 and
PHYx1.
Besides, assert the common lane reset when disable pll. This still
to be determined whether need to do it by driver.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Don't disable DPIO PLL when using DSI]
[vsyrjala: Don't call vlv_disable_pll() by accident on CHV]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Move part of a moved comment back as suggested by Imre since
it's valid for both byt and chv.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cherryview has 3 pipes. Some of the pll dpio offset calculation is
based on pipe number. Need to use vlv_pipe_to_channel to calculate the
correct phy channel to use for the pipe.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The additional DPLL registers added to support Port D. Besides, add
some new PHY control and status registers based on B-spec.
v2: Based on Ville review
- Corrected DPIO_PHY_STATUS offset and name.
- Rebase based on upstream change after introduce enum dpio_phy and
enum dpio_channel.
v3: Rebased on top of Antti's 3-pipe prep patch. Note that the new offsets for
the DPLL registers aren't in place yet, so this introduces a slight regression.
But since 3 pipe support isn't fully enabled yet anyaway in -internal this
shouldn't matter too much.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has 2 display phys. First phy (IOSF offset 0x1A) has two channels,
and second phy (IOSF offset 0x12) has single channel. The first phy is
used for port B and port C, while second phy is only for port D.
v2: Move the pipe to determine which phy to select for
vlv_dpio_read/vlv_dpio_write to another patch. (Daniel)
v3: Rebase the code based on rework on how to calculate DPIO offset.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fill in the sprite bits for DDL1/DDL2 registers, and add DDL3.
Still need to write the code to use these...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Update to also fill in the new num_pipes field.
v3: Rebase on top of the pciid extraction.
v4: Switch from info->has*ring to info->ring mask. Also add VEBOX support whiel
at it.
v5: s/CHV_PCI_IDS/CHV_IDS/, and drop the trailing '\'
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV clock gating isn't identical to VLV, so add a new function
for it. This is only a start, and further changes are needed as
the details become available.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make i915_gem_interrupt debugfs file functional on CHV.
FIXME: Extract helpers for gt/display blocks to shrink the function a
bit and avoid duplication between bdw/chv (and other similar cases for
upstream).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Inspired by a review bikeshed from Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has the Gen8 master interrupt register, as well as Gen8
GT/PCU interrupt registers.
The display block is based on VLV, with the main difference
of adding pipe C.
v2: Rewrite the order of operations to make more sense
Don't bail out if MASTER_CTL register doesn't show an interrupt,
as display interrupts aren't reported there.
v3: Rebase on top of Egbert Eich's hpd irq handling rework by using
the relevant port hotplug logic like for vlv.
v4: Rebase on top of Ben's gt irq #define refactoring.
v5: Squash in gen8_gt_irq_handler refactoring from Zhao Yakui
<yakui.zhao@intel.com>
v6: Adapt to upstream changes, dev_priv->irq_received is gone.
v7: Enable 3 the commented-out 3 pipe support.
v8: Rebase on top of Paulo's irq setup rework, use the renamed macros from
upstream.
v9: Grab irq_lock around i915_enable_pipestat()
FIXME: There's probably some potential for more shared code between bdw and chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the unnecessary cast Jani spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For clients that submit large batch buffers the command parser has
a substantial impact on performance. On my HSW ULT system performance
drops as much as ~20% on some tests. Most of the time is spent in the
command lookup code. Converting that from the current naive search to
a hash table lookup reduces the performance drop to ~10%.
The choice of value for I915_CMD_HASH_ORDER allows all commands
currently used in the parser tables to hash to their own bucket (except
for one collision on the render ring). The tradeoff is that it wastes
memory. Because the opcodes for the commands in the tables are not
particularly well distributed, reducing the order still leaves many
buckets empty. The increased collisions don't seem to have a huge
impact on the performance gain, but for now anyhow, the parser trades
memory for performance.
NB: Ville noticed that the error paths through the ring init code
will leak memory. I've not addressed that here. We can do a follow
up pass to handle all of the leaks.
v2: improved comment describing selection of hash key mask (Damien)
replace a BUG_ON() with an error return (Tvrtko, Ville)
commit message improvements
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the same code for enabling/disabling planes on all platforms. Rename
the functions to reflect that they're no longer specific to any
platform.
For now we leave the plane enable/disable to ccur at the same old
position in the modeset sequence.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Frob drm_vblank_on conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During the review of
commit 1f70999f90
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Jan 27 22:43:07 2014 +0000
drm/i915: Prevent recursion by retiring requests when the ring is full
Ville raised the point that our interaction with request->tail was
likely to foul up other uses elsewhere (such as hang check comparing
ACTHD against requests).
However, we also need to restore the implicit retire requests that certain
test cases depend upon (e.g. igt/gem_exec_lut_handle), this raises the
spectre that the ppgtt will randomly call i915_gpu_idle() and recurse
back into intel_ring_begin().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78023
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Remove now unused 'tail' variable as spotted by Brad.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few improvements to the fallback method for waiting upon ring space:
1. Fix the start/end wait tracepoints to always be paired.
2. Increase responsiveness of checking
3. Mark the process as waiting upon io
4. Check for signal interruptions
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Drop the s/msleep/io_schedule_timeout/ change again since the
latter isn't exported.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a good debate to be had about how best to fit the aliasing
PPGTT into the code. However, as it stands right now, getting aliasing
PPGTT bindings is a hack, and done through implicit arguments. To make
this absolutely clear, WARN and return an error if a driver writer tries
to do something they shouldn't.
I have no issue with an eventual revert of this patch. It makes sense
for what we have today.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It was always the intention to do the topdown allocation for context
objects (Chris' idea originally). Unfortunately, I never managed to land
the patch, but someone else did, so now we can use it.
As a reminder, hardware contexts never need to be in the precious GTT
aperture space - which is what is what happens with the normal bottom up
allocation we do today. Doing a top down allocation increases the odds
that the HW contexts can get out of the way, especially with per FD
contexts as is done in full PPGTT
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add runtime PM support for VLV, but leave it disabled. The next patch
enables it.
The suspend/resume sequence used is based on [1] and [2]. In practice we
depend on the GT RC6 mechanism to save the HW context depending on the
render and media power wells. By the time we run the runtime suspend
callback the display side is also off and the HW context for that is
managed by the display power domain framework.
Besides the above there are Gunit registers that depend on a system-wide
power well. This power well goes off once the device enters any of the
S0i[R123] states. To handle this scenario, save/restore these Gunit
registers. Note that this is not the complete register set dictated by
[2], to remove some overhead, registers that are known not to be used are
ignored. Also some registers are fully setup by initialization functions
called during resume, these are not saved either. The list of registers
can be further reduced, see the TODO note in the code.
[1] VLV_gfx_clocking_PM_reset_y12w21d3 / "Driver D3 entry/exit"
[2] VLV2_S0IXRegs
v2:
- unchanged
v3:
- fix s/GEN6_PMIIR/GEN6_PMIMR/ typo when saving/restoring registers
(Ville)
v4:
- rebased on the previous patch fixing GEN register prefixes
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[ rebased (according to v4) ]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, none of the RPM callbacks can fail, but the next patch adding
RPM support for VLV changes this, so prepare for it.
In case one of these callbacks return error RPM will get permanently
disabled until the error is explicitly cleared. In the future we could
add support for re-enabling it, for example after resetting the HW, but
for now - hopefully - we can live with the simpler solution.
v2:
- propagate the error from the resume callbacks too (Paulo)
v3:
- fix rebase fail typo around IS_GEN6() check in intel_runtime_suspend()
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needed by the VLV S0ix context save/restore helpers.
v2:
- unchanged
v3:
- use proper GEN register prefixes (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to Pipe C DPINVGTT has more bits on CHV.
v2: Fix comment to say VLV/CHV (Rafael)
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebase on top of Ben's GT interrupt shuffling.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has pipe C and PSR which cause changes to DPFLIPSTAT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIXME: We probably want to sprinkle _CHV suffixes over these.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable aliasing PPGTT for CHV, but keep full PPGTT still disabled until
it gets enabled for BDW.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Page table updates were getting stuck in the CPU cache on chv causing
spurious page faults and strange behaviour.
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: Add !HAS_LLC checks]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ignore the cache bits in PPAT and just set the snoop bit where
appropriate. BDW WB is mapped to snooped access, while all other
modes are mapped to non-snooped access.
The hardware supposedly ignores everything except the snoop bit
in the PPAT entries.
Additionally the hardware actually enforces snooping for all
page table accesses, and thus the snoop bit is ignored for PDEs.
v2: Rebased on top of the bdw resume fix to reload the ppat entries.
v3: Rebase on top of the i915_gem_gtt.h header extraction.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We won't be calling intel_enable_primary_plane() or
intel_disable_primary_plane() with the primary plane in the
wrong state. So remove the useless DISPLAY_PLANE_ENABLE checks.
v2: Convert the checks to WARNs instead (Daniel,Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On ILK when we disable a particular watermark level, we must
maintain the actual watermark values for that level for some time
(until the next vblank possibly). Otherwise we risk underruns.
In order to achieve that result we must merge the LP1+ watermarks a
bit differently since we must also merge levels that are to be
disabled. We must also make sure we don't overflow the fields in the
watermark registers in case the calculated watermarks come out too
big to fit.
As early as possbile we mark all computed watermark levels as
disabled if they would exceed the register maximums. We make sure
to leave the actual watermarks for such levels zeroed out. Then during
merging, we take the maxium values for every level, regardless if
they're disabled or not. That may seem a bit pointless since at the
moment all the watermark levels we merge should have their values
zeroed if the level is already disabled. However soon we will be
dealing with intermediate watermarks that, in addition to the new
watermark values, also contain the previous watermark values, and so
levels that are disabled may no longer be zeroed out.
v2: Split the patch in two (Paulo)
Use if() instead of & when merging ->enable (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix commit message as noted by Paulo.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we calculate the watermarks for a pipe make sure we leave any
level fully zeroed out if it would exceed any of the maximum values
that fit in the registers.
This will be important later when we start to use also disabled
watermark levels during LP1+ merging.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add trace points for observing the atomic pipe update mechanism.
v2: Rebased due to earlier changes
v3: Pass intel_crtc instead of drm_crtc (Daniel)
v4: Pass frame counter from the caller to evaded/end since
the caller now always has that ready
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the primary plane enable/disable to occur atomically with the
sprite update that caused the primary plane visibility to change.
FBC and IPS enable/disable is left to happen well before or after
the primary plane change.
v2: Pass intel_crtc instead of drm_crtc (Daniel)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a mechanism by which we can evade the leading edge of vblank. This
guarantees that no two sprite register writes will straddle on either
side of the vblank start, and that means all the writes will be latched
together in one atomic operation.
We do the vblank evade by checking the scanline counter, and if it's too
close to the start of vblank (too close has been hardcoded to 100usec
for now), we will wait for the vblank start to pass. In order to
eliminate random delayes from the rest of the system, we operate with
interrupts disabled, except when waiting for the vblank obviously.
Note that we now go digging through pipe_to_crtc_mapping[] in the
vblank interrupt handler, which is a bit dangerous since we set up
interrupts before the crtcs. However in this case since it's the vblank
interrupt, we don't actually unmask it until some piece of code
requests it.
v2: preempt_check_resched() calls after local_irq_enable() (Jesse)
Hook up the vblank irq stuff on BDW as well
v3: Pass intel_crtc instead of drm_crtc (Daniel)
Warn if crtc.mutex isn't locked (Daniel)
Add an explicit compiler barrier and document the barriers (Daniel)
Note the irq vs. modeset setup madness in the commit message (Daniel)
v4: Use prepare_to_wait() & co. directly and eliminate vbl_received
v5: Refactor intel_pipe_handle_vblank() vs. drm_handle_vblank() (Chris)
Check for min/max scanline <= 0 (Chris)
Don't call intel_pipe_update_end() if start failed totally (Chris)
Check that the vblank counters match on both sides of the critical
section (Chris)
v6: Fix atomic update for interlaced modes
v7: Reorder code for better readability (Chris)
v8: Drop preempt_check_resched(). It's not available to modules
anymore and isn't even needed unless we ourselves cause
a wakeup needing reschedule while interrupts are off
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the rest of the code to enable this is in my branch. Without my
branch, hitting > 32b offsets is impossible. The code has always
"supported" 64b, but it's never actually been run of tested. This change
doesn't actually fix anything. [1] I am not sure why X won't work yet. I
do not get hangs or obvious errors.
There are 3 fixes grouped together here. First is to remove the
hardcoded 0 for the upper dword of the relocation. The next fix is to
use a 64b value for target_offset. The final fix is to not directly
apply target_offset to reloc->delta. reloc->delta is part of ABI, and so
we cannot change it. As it stands, 32b is enough to represent everything
we're interested in representing anyway. The main problem is, we cannot
add greater than 32b values to it directly.
[1] Almost all of intel-gpu-tools is not yet ready to test 64b
relocations. There are a few places that expect 32b values for offsets
and these all won't work.
Cc: Rafael Barbalho <rafael.barbalho@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously, our code only had a 32b offset value for where the
batchbuffer starts. With full PPGTT, and 64b canonical GPU address
space, that is an insufficient value. The code to expand is pretty
straight forward, and only one platform needs to do anything with the
extra bits.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SDVO is used by both crtcs using the i9xx_ and the ironlake_
functions. For both cases there is nothing between the
encoder->mode_set and the encoder->pre_enable calls that touches the
hardware.
The vlv_ functions are different since they enable the pll before the
->pre_enable hook. But SDVO isn't supported on vlv platforms, so this
doesn't matter.
We've also already clean up all the sdvo state computation logic, all
relevant parts are already in the ->compute_config hook. So we can
just get rid of the ->mode_set hook by converting it to a ->pre_enable
hook.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only set a few bits in the ADPA register, which we then read back
in the enable/disable hooks. So we can just move that bit of state
computation code to the place where we need it since setting these
bits without enabling the CRT encoder has no effects.
The only exceptions are the hotplug bits since they affect the hotplug
detection logic, but we already set those in the ->reset function and
then never touch them.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently for the i9xx crtc hooks there's nothing between the call to
encoder->mode_set and encoder->pre_enable which touches the hardware.
Therefore, since tv is only used on gen3/4, we can just move the hook.
Yay for easy cases!
The only other important thing to check is that the new
->pre_enable hook is idempotent wrt the sw state since now it can
be called multiple times (due to DPMS). After a the bit of refactoring
this is now easy to check: It only reads crtc->config and computes
derived state but otherwise leaves it as-is, so we're good.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe and plane _are_ disabled when we call this. So replace it
all with the corresponding assert (as self-documenting code) and
rip out all the lore.
Checking for a disabled plane would require us to export those macros
from intel_display.c, but if the pipe is off the plane isn't working
either. So this single check is good enough.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only support TV-out on gen3/4 mobile platforms, and i915gm is the
only one that matches.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently for the i9xx crtc hooks there's nothing between the call to
encoder->mode_set and encoder->pre_enable which touches the hardware.
Therefore, since dvo is only used on gen2, we can just move the hook.
Yay for easy cases!
The only other important thing to check is that the new
->pre_enable hook is idempotent wrt the sw state since now it can be
called multiple times (due to DPMS). It only reads crtc->config but
otherwise leaves it as-is, so we're good.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reasons we want to move away from the ->mode_set
callbacks: All hw state setup needs to move into ->enable hooks (so
that DOMS can do runtime pm) and all the configuration setup needs to
move into the compute_config functions.
To start with this make the enocer->mode_set callback optional.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BIOS can enable a pipe but leave the primary plane disabled. This
coflicts with out current idea of primary_enabled. Read the actual
hardware plane state and set primary_enabled appropriately.
We currently assume that primary_enabled is always true when we're about
to disable a crtc. That needs to change now as the plane may not be
enabled. So replace the relevant WARNs with early returns in
intel_{enable,disable}_primary_hw_plane().
Fixes the following warning
[ 3.831602] WARNING: CPU: 0 PID: 1112 at linux/drivers/gpu/drm/i915/intel_display.c:1918 intel_disable_primary_hw_plane+0xe4/0xf0 [i915]()
which got introduced here by me:
commit e9e39655c0c30cddc3f8c09a757678a24dd36737
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Apr 28 15:53:25 2014 +0300
drm/i915: Remove useless checks from primary enable/disable
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add_request has always contained both the semaphore mailbox updates as
well as the breadcrumb writes. Since the semaphore signal is the one
which actually knows about the number of dwords it needs to emit to the
ring, we move the ring_begin to that function. This allows us to remove
the hideously shared #define
On a related not, gen8 will use a different number of dwords for
semaphores, but not for add request.
v2: Make number of dwords an explicit part of signalling (via function
argument). (Chris)
v3: very slight comment change
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This abstraction again is in preparation for gen8. Gen8 will bring new
semantics for doing this operation.
While here, make the writes of MI_NOOPs explicit for non-existent rings.
This should have been implicit before.
NOTE: This is going to be removed in a few patches.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be helpful in abstracting some of the code in preparation for
gen8 semaphores.
v2: Move mbox stuff to a separate struct
v3: Rebased over VCS2 work
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During the initial power well enabling on the driver init/resume path
we can avoid initialzing part of the HW/SW state that will be
initialized anyway by the subsequent init/resume code. For some steps
like HPD initialization this redundancy is not only an overhead but an
actual problem, since they can't be run this early in the overall init
sequence.
Add a flag marking the init phase and skip reinitialzing state that is
not strictly necessary based on that.
This is also needed by the upcoming HPD init restructuring by Thierry
and Daniel.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit 691e6415c8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Apr 9 09:07:36 2014 +0100
drm/i915: Always use kref tracking for all contexts.
we populated fake contexts on all platforms. These were identical to the
full hardware context tracking structs, except for the ctx->obj used to
store the hardware state. However, there remained one place where we
assumed that if a context existed, it would have an object associated
with it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77717
Testcase: igt/drv_suspend/debugfs-reader
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new function intel_get_crtc_scanline() that returns the current
scanline counter for the crtc.
v2: Rebase after vblank timestamp changes.
Use intel_ prefix instead of i915_ as is more customary for
display related functions.
Include DRM_SCANOUTPOS_INVBL in the return value even w/o
adjustments, for a bit of extra consistency.
v3: Change the implementation to be based on DSL on all gens,
since that's enough for the needs of atomic updates, and
it will avoid complicating the scanout position calculations
for the vblank timestamps
v4: Don't break scanline wraparound for interlaced modes
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Seems I've been a bit dense with regards to the start of vblank
vs. the scanline counter / pixel counter.
After staring at the pixel counter on gen4 I came to the conclusion
that the start of vblank interrupt and scanline counter increment
happen at the same time. The scanline counter increment is documented
to occur at start of hsync, which means that the start of vblank
interrupt must also trigger there. Looking at the pixel counter value
when the scanline wraps from vtotal-1 to 0 confirms that, as the pixel
counter at that point reads hsync_start. This also clarifies why we see
need the +1 adjustment to the scaline counter. The counter actually
starts counting from vtotal-1 on the first active line.
I also confirmed that the frame start interrupt happens ~1 line after
the start of vblank, but the frame start occurs at hblank_start instead.
We only use the frame start interrupt on gen2 where the start of vblank
interrupt isn't available. The only important thing to note here is that
frame start occurs after vblank start, so we don't have to play any
additional tricks to fix up the scanline counter.
The other thing to note is the fact that the pixel counter on gen3-4
starts counting from the start of horizontal active on the first active
line. That means that when we get the start of vblank interrupt, the
pixel counter reads (htotal*(vblank_start-1)+hsync_start). Since we
consider vblank to start at (htotal*vblank_start) we need to add a
constant (htotal-hsync_start) offset to the pixel counter, or else we
risk misdetecting whether we're in vblank or not.
I talked a bit with Art Runyan about these topics, and he confirmed my
findings. And that the same rules should hold for platforms which don't
have the pixel counter. That's good since without the pixel counter it's
rather difficult to verify the timings to this accuracy.
So the conclusion is that we can throw away all the ISR tricks I added,
and just increment the scanline counter by one always.
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems we need this at least for the current platforms we have, but
probably not later. In any event, it should cause too much harm as we do
the same thing on several other platforms.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The same register exists for querying and programming eDRAM AKA eLLC. So
we can simply use it. For now, use all the same defaults as we had
for Haswell, since like Haswell, I have no further details.
I do not actually have a part with eDRAM, so I cannot test this.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I don't have any insight on what parts can do what. The docs do seem to
suggest WT caching works in at least the same manner as it does on
Haswell.
The addr = 0 is to shut up GCC:
drivers/gpu/drm/i915/i915_gem_gtt.c:80:7: warning: 'addr' may be used
uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On BDW we don't enable RC6 at the moment, but this isn't reflected in
the (sanitized) i915.enable_rc6 option. So make enable_rc6 report
correctly that RC6 is disabled, which will also effectively disable RPM
on BDW (since RPM depends on RC6).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77565
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
assert_plane_enabled() is now triggering during FDI link train because
we no longer enable planes that early.
This problem got introduced in:
commit a5c4d7bc18
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Mar 7 18:32:13 2014 +0200
drm/i915: Disable/enable planes as the first/last thing during modeset on ILK+
Just drop the assert since we shouldn't need planes for link training.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Squash in fixup for now unused plane local variable, reported
by 0-day tester.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 60f2b4af12.
The same warning has been fixed in e5081a538a and
these two commits got merged in 74e99a84de2d0980320612db8015ba606af42114 which
caused another warning. Simply, the reverted commit casted the pointer
difference to unsigned long and the other commit changed the output type from
long to ptrdiff_t.
The other commit fixes the original warning the better way so I'm reverting
this commit now.
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In recent dmesg logs reported for unrelated issues I noticed some power
domain WARNs caused by the following.
The workaround
commit ce35255032
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 20 10:14:23 2013 +0300
drm/i915: Fix unclaimed register access due to delayed VGA memory disable
and following fixup of it
commit a148532065
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Sep 16 17:38:34 2013 +0300
drm/i915: Move power well init earlier during driver load
was partially reverted by
commit 7f16e5c141
Merge: 9d1cb915e01dc7
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Nov 4 16:28:47 2013 +0100
Merge tag 'v3.12' into drm-intel-next
but kept the power domain put calls on the error path.
I think for now we can keep things as-is (not reintroduce the w/a) and just fix
the error path, since
- nobody complained seeing this issue
- according to Ville someone is reworking the VGA arbitration scheme at the
moment and when that's ready we have to rethink this part anyway
So fix this by just removing the put calls from the error path as well.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville noticed that we have this nice kerneldoc but it's not integrated
anywhere. Fix this asap!
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A common issue we have is that retiring requests causes recursion
through GTT manipulation or page table manipulation which we can only
handle at very specific points. However, to maintain internal
consistency (enforced through our sanity checks on write_domain at
various points in the GEM object lifecycle) we do need to retire the
object prior to marking it with a new write_domain, and also clear the
write_domain for the implicit flush following a batch.
Note that this then allows the unbound objects to still be on the active
lists, and so care must be taken when removing objects from unbound lists
(similar to the caveats we face processing the bound lists).
v2: Fix i915_gem_shrink_all() to handle updated object lifetime rules,
by refactoring it to call into __i915_gem_shrink().
v3: Missed an object-retire prior to changing cache domains in
i915_gem_object_set_cache_leve()
v4: Rebase
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've seen latencies up to 15msec, so increase the timeout to 20msec.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by the VLV runtime PM helpers too, so factor it out.
Also add a safety check for the case where the previous force-off is
still pending, since I'm not sure if Punit can handle a new setting
while the previous one hasn't settled yet.
v2:
- unchanged
v3:
- add a note to the commit message about the safety check (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When enabling runtime PM on VLV, GT power save enabling becomes relatively
frequent, so optimize it a bit.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During runtime suspend there can be a last pending rps.work, so make
sure it's canceled. Note that in the runtime suspend callback we can't
get any RPS interrupts since it's called only after the GPU goes idle
and we set the minimum RPS frequency. The next possibility for an RPS
interrupt is only after getting an RPM ref (for example because of a new
GPU command) and calling the RPM resume callback.
v2:
- patch introduced in v2 of the patchset
v3:
- Change the order of canceling the rps.work and disabling interrupts to
avoid the race between interrupt disabling and the the rps.work. Race
spotted by Ville.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init sizzling on all platforms so move it to the
platform independent runtime resume callback. The ring frequency reinit
is also needed everywhere except on VLV, but gen6_update_ring_freq()
will be a noop on VLV, so we can move this function too to platform
independent code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by the next patch moving the call out from platform
specific RPM callbacks to platform independent code.
No functional change.
v2:
- patch introduce in v2 of the patchset
v3:
- simplify platform check condition (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to disable the interrupts for all platforms, so make the helpers
for this platform independent and call them from them platform
independent runtime suspend/resume callbacks.
On HSW/BDW this will move interrupt disabling/re-enabling at the
beginning/end of runtime suspend/resume respectively, but I don't see
any reason why this would cause a problem there. In any case this seems
to be the correct thing to do even on those platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV we depend on RC6 to save the GT render and media HW context
before going to the D3 state via RPM, so as a preparation for the
VLV RPM support (added in an upcoming patch) disable RPM if RC6 is
disabled.
There is probably a similar dependency on other platforms too, so for
safety require RC6 for those too. For these platforms (SNB, HSW, BDW)
this is then a possible fix.
v2:
- require RC6 for all RPM platforms, not just for VLV (Paulo, Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, an invalid enable_rc6 module option will be silently ignored, so
emit an info message about it. Doing an early sanitization we can also
reuse intel_enable_rc6() in a follow-up patch to see if RC6 is actually
enabled. Currently the caller would have to filter a non-zero return
value based on the platform we are running on. For example on VLV with
i915.enable_rc6 set to 2, RC6 won't be enabled but atm
intel_enable_rc6() would still return 2 in this case.
v2:
- simplify the platform check condition (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, we call intel_gt_powersave_enable() for GEN6 and GEN7 but disable
it for everything starting from GEN6. This is a problem in case of BDW.
Since I don't have a BDW to test if RC6 works properly, just keep it
disabled for now and fix only the disable function.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some platforms need additional power domains to be on in addition to the
device D0 state to access the panel registers.
Suggested by Daniel.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76987
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While checking the error capture path I noticed that we lacked the
power domain-on check for PIPESTAT so fix this by moving that to where
the rest of pipe registers are captured.
The move also revealed that we actually don't include this register in
the error report, so fix that too.
v2:
- patch introduced in v2 of the patchset
v3:
- add back !HAS_PCH_SPLIT check (Ville)
[ Ignore my previous comment about the gen<=5 || vlv check, I realized
that it's the same as !HAS_PCH_SPLIT. ]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While checking the error capture path I noticed that this register is
read twice for GEN2, so fix this and also move the read where it's done
for other platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we can end up in the GPU reset deferred work in D3 state if the last
runtime PM reference is dropped between detecting a hang/scheduling the
work and executing the work. At least one such case I could trigger is
the simulated reset via the i915_wedged debugfs entry. Fix this by
getting an RPM reference around accessing the HW in the reset work.
v2:
- Instead of getting/putting the RPM reference in the reset work itself,
get it already before scheduling the work. By this we also prevent
going to D3 before the work gets to run, in addition to making sure
that we run the work itself in D0. (Ville, Daniel)
v3:
- fix inverted logic fail when putting the RPM ref on behalf of a
cancelled GPU reset work (Ville)
v4:
- Taking the RPM ref in the interrupt handler isn't really needed b/c
it's already guaranteed that we hold an RPM ref until the end of the
reset work in all cases we care about. So take the ref in the reset
work (for cases like i915_wedged_set). (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Be we read and chase pointers from the VBT, it is prudent to make sure
that those accesses are wholly contained within the MMIO region, or else
we may cause a kernel panic during boot.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure that the whole BDB section is within the MMIO region prior to
accessing it contents. That we don't read outside of the secion is left
up to the individual section parsers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on VLV but probably on other platforms too we depend on RC6
being enabled for RPM, so disable RPM until the delayed RC6 enabling
completes.
v2:
- explain the reason for the _noresume version of RPM get (Daniel)
- use the simpler 'if (schedule_work()) rpm_get();' instead of
'if (!cancel_work_sync()) rpm_get(); schedule_work();'
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Getting struct_mutex around the whole intel_enable_gt_powersave()
function is not necessary, since it's only needed for the ILK path
therein.
This will make intel_enable_gt_powersave() useable on the RPM resume
path for >=GEN6 (added in an upcoming patch to reset the RPS state
during RPM resume), where we can't (and need not) get this mutex.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These debugfs entries access registers that need the D0 power state so
get an RPM ref for them.
v2:
- for all these entries we only need D0 state, so get only an RPM ref,
not a power domain ref (Daniel, Paulo)
- the dpio entry is not an issue any more as it got removed (Ville)
- restore commit message from v1 (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are igt tools that can read/write the DPIO registers, so having a
debugfs entry for only some of those registers is somewhat arbitrary /
redundant. Remove it.
v2:
- instead of fixing the entry by taking a power domain reference around
the register accesses, remove the entry (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The parsing was incorrect for ILK and VLV.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not clearing this flag causes spurious interrupts at least in D3 state,
so before enabling RPM we need to fix this. We were already setting this
flag when enabling interrupts, only clearing it was missing.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These will be needed by the upcoming VLV RPM helpers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BDW GT3 has two independent BSD rings, which can be used to process the
video commands. To be simpler, it is transparent to user-space driver/middle.
Instead the kernel driver will decide which ring is to dispatch the BSD video
command.
As every BSD ring is powerful, it is enough to dispatch the BSD video command
based on the drm fd. In such case it can play back video stream while encoding
another video stream. The coarse ping-pong mechanism is used to determine
which BSD ring is used to dispatch the BSD video command.
V1->V2: Follow Daniel's comment and use the simple ping-pong mechanism.
This is only to add the support of dual BSD rings on BDW GT3 machine.
The further optimization will be considered in another patch set.
V2->V3: Follow Daniel's comment to use the struct_mutext instead of
atomic_t during determining which ring can be used to dispatch Video command.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Gen7 doesn't have the second BSD ring. But it will complain the switch check
warning message during compilation. So just add it to remove the
switch check warning.
V1->V2: Follow Daniel's comment to update the comment
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 machine has two independent
BSD ring that can be used to dispatch the video commands.
So just initialize it.
V3->V4: Follow Imre's comment to do some minor updates. For example:
more comments are added to describe the semaphore between ring.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[danvet: Fix up checkpatch error.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 has the different configuration
with the BDW GT1/GT2. So split the BDW device info definition.
This is to do the preparation for adding the Dual BSD rings on BDW GT3 machine.
V1->V2: Follow Daniel's comment to pay attention to the stolen check for BDW
in kernel/early-quirks.c
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to make sure that userspace keeps on following the contract,
otherwise we won't be able to use the reserved fields at all.
v2: Add DRM_DEBUG (Chris)
Testcase: igt/gem_exec_params/*-dirt
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bit tricky since 0 is also a valid constant ...
v2: Add DRM_DEBUG (Chris)
Testcase: igt/gem_exec_params/rel-constants-*
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we catch it, but silently succeed. Our userspace is
better than this.
v2: Add DRM_DEBUG (Chris)
Testcase: igt/gem_exec_params/sol-reset-*
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we include the expected values for the failing ring register checks,
it makes it marginally easier to see which is the culprit.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During module load, if we fail to initialise the rings, we abort the
load reporting EIO. However during resume, even though we report EIO as
we fail to reinitialize the ringbuffers, the resume continues and the
device is restored - albeit in a non-functional state. As we cannot
execute any commands on the GPU, it is effectively wedged, mark it so.
As we now preserve the ringbuffers across resume, this should prevent
UXA from falling into the trap of repeatedly sending invalid
batchbuffers and dropping all further rendering into /dev/null.
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: Drop unused error, spotted by Oscar.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even without enabling the ringbuffers to allow command execution, we can
still control the display engines to enable modesetting. So make the
ringbuffer initialization failure soft, and mark the GPU as wedged
instead.
v2: Only treat an EIO from ring initialisation as a soft failure, and
abort module load for any other failure, such as allocation failures.
v3: Add an *ERROR* prior to declaring the GPU wedged so that it stands
out like a sore thumb in the logs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tearing down the ring buffers across resume is overkill, risks
unnecessary failure and increases fragmentation.
After failure, since the device is still active we may end up trying to
write into the dangling iomapping and trigger an oops.
v2: stop_ringbuffers() was meant to call stop(ring) not
cleanup(ring) during resume!
Reported-by: Jae-hyeon Park <jhyeon@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72351
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: s/ring->obj == NULL/!intel_ring_initialized(ring)/ as
suggested by Oscar.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For readibility and guess at the meaning behind the constants.
v2: Claim only the meagerest connections with reality.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I don't think this is necessary; at least it doesn't appear to be on my
BYT. Dropping it speeds up our shutdown code a little, in some cases
resulting in faster init times.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Next pull request, this time more of the drm de-midlayering work. The big
thing is that his patch series here removes everything from drm_bus except
the set_busid callback. Thierry has a few more patches on top of this to
make that one optional to.
With that we can ditch all the non-pci drm_bus implementations, which
Thierry has already done for the fake tegra host1x drm_bus.
Reviewed by Thierry, Laurent and David and now also survived some testing
on my intel boxes to make sure the irq fumble is fixed correctly ;-) The
last minute rebase was just to add the r-b tags from Thierry for the 2
patches I've redone.
* 'drm-init-cleanup' of git://people.freedesktop.org/~danvet/drm:
drm/<drivers>: don't set driver->dev_priv_size to 0
drm: Remove dev->kdriver
drm: remove drm_bus->get_name
drm: rip out dev->devname
drm: inline drm_pci_set_unique
drm: remove bus->get_irq implementations
drm: pass the irq explicitly to drm_irq_install
drm/irq: Look up the pci irq directly in the drm_control ioctl
drm/irq: track the irq installed in drm_irq_install in dev->irq
drm: rename dev->count_lock to dev->buf_lock
drm: Rip out totally bogus vga_switcheroo->can_switch locking
drm: kill drm_bus->bus_type
drm: remove drm_dev_to_irq from drivers
drm/irq: remove cargo-culted locking from irq_install/uninstall
drm/irq: drm_control is a legacy ioctl, so pci devices only
drm/pci: fold in irq_by_busid support
drm/irq: simplify irq checks in drm_wait_vblank
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
In commit a51435a313
Author: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Date: Wed Mar 12 16:39:40 2014 +0530
drm/i915: disable rings before HW status page setup
we reordered stopping the rings to do so before we set the HWS register.
However, there is an extra workaround for g45 to reset the rings twice,
and for consistency we should apply that workaround before setting the
HWS to be sure that the rings are truly stopped.
Reference: http://lkml.kernel.org/r/20140423202248.GA3621@amd.pavel.ucw.cz
Tested-by: Pavel Machek <pavel@ucw.cz>
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The status bits are unconditionally set, the control bits only enable
the actual interrupt generation. Which means if we get some random
other interrupts we'll bogusly complain about them.
So restrict the WARN to platforms with a sane hotplug interrupt
handling scheme. And even more important also don't attempt to process
the hpd bit since we've detected a storm already. Instead just clear
the bit silently.
This WARN has been introduced in
commit b8f102e8bf
Author: Egbert Eich <eich@suse.de>
Date: Fri Jul 26 14:14:24 2013 +0200
drm/i915: Add messages useful for HPD storm detection debugging (v2)
before that we silently handled the hpd event and so partially
defeated the storm detection.
v2: Pimp commit message (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Egbert Eich <eich@suse.de>
Cc: bitlord <bitlord0xff@gmail.com>
Reported-by: bitlord <bitlord0xff@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When PPGTT was disabled by default, the patch also prevented the user
from overriding this behavior via module parameter. Being able to test
this on arbitrary kernels is extremely beneficial to track down the
remaining bugs. The patch that prevented this was:
commit 93a25a9e2d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 6 09:40:43 2014 +0100
drm/i915: Disable full ppgtt by default
By default PPGTT is set to -1. 0 means off, 1 means aliasing only, 2
means full, all other values are reserved.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If the inherited BIOS framebuffer is smaller than the mode selected for
fbdev, then if we continue to use it then we cause display corruption as
we do not setup the panel fitter to upscale.
Regression from commit d978ef1445
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Mar 7 08:57:51 2014 -0800
drm/i915: Wrap the preallocated BIOS framebuffer and preserve for KMS fbcon v12
v2: Add a debug message to track the discard of the BIOS fb.
v3: Ville pointed out the difference between ref/unref
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77767
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Unfortunately this requires a drm-wide change, and I didn't see a sane
way around that. Luckily it's fairly simple, we just need to inline
the respective get_irq implementation from either drm_pci.c or
drm_platform.c.
With that we can now also remove drm_dev_to_irq from drm_irq.c.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I just wanted to add a new field to struct drm_device and
accidentally stumbled over something. According to comments
dev->open_count is protected by dev->count_lock, but that's totally
not the case. It's protected by drm_global_mutex.
Unfortunately the vga switcheroo callbacks took this comment at face
value. The problem is that we can't just take the drm_global_mutex
because:
- It would lead to a locking inversion with the driver load/unload
paths.
- It wouldn't actually protect anything, for that we'd need to wrap
the entire vga switcheroo code in the drm_global_mutex. And I'm not
sure whether that would actually solve anything.
What we probably want is a try_to_grab_switcheroo reference kind of
thing which is used in the driver's ->open callback. Then we could
move all that ->can_switch madness into the vga switcheroo core where
it really belongs.
But since that would amount to real work take the easy way out and
just add a comment. It's definitely not going to make anything worse
since doing switcheroo state changes while restarting X just isn't
recommended. Even though the delayed switching code does exactly that.
v2:
- Simplify the ->can_switch implementations more (Thierry)
- Fix comment about the dev->open_count locking (Thierry)
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> (v1)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If I unplug the eDP monitor, the BIOS of my machine will enable the
VDD bit, then when the driver loads it will think VDD is enabled. It
will detect that the eDP is not enabled and return false from
intel_edp_init_connector. This will trigger a call to
edp_panel_vdd_off_sync(), which trigger a WARN saying that the
refcount of the power domain is less than zero.
The problem happens because the driver gets a refcount whenever it
enables the VDD bit, and puts the refcount whenever it disables the
VDD bit. But on this case, the BIOS enabled VDD, so all we do is to
call put() without calling get() first, so the code added is there to
make sure we always have the get() in case the BIOS enabled the bit.
This regression was introduced in
commit e9cb81a228
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Nov 21 13:47:23 2013 -0200
drm/i915: get a runtime PM reference when the panel VDD is on
v2: - Rebase
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
... our current modeset code isn't good enough yet to handle this. The
scenario is:
1. BIOS sets up a cloned config with lvds+external screen on the same
pipe, e.g. pipe B.
2. We read out that state for pipe B and assign the gmch_pfit state to
it.
3. The initial modeset switches the lvds to pipe A but due to lack of
atomic modeset we don't recompute the config of pipe B.
-> both pipes now claim (in the sw pipe config structure) to use the
gmch_pfit, which just won't work.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74081
Tested-by: max <manikulin@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In commit
commit 6375b768a9
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Mar 3 11:33:36 2014 +0200
drm/i915: Reject >165MHz modes w/ DVI monitors
the driver started to filter out display modes which exceed the
single-link DVI 165Mz dotclock limits when the monitor doesn't report
itself as being HDMI compliant. The intent was to filter out all
EDID derived modes that require dual-link DVI to operate since we
don't support dual-link.
However the patch went a bit too far and also causes the driver to reject
such modes even when specified by the user. Normally we don't check the
sink limitations when setting a mode from the user. This allows the user
to specify any mode whether the sink reports to support it or not. This
can be useful since often the sinks support more modes than they report
in the EDID.
So relax the checks a bit, and apply the single-link DVI dotclock limit
only when filtering the mode list, and ignore the limit when setting
a user specified mode.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72961
Tested-by: Nicholas Vinson <nvinson@comcast.net>
Cc: stable@vger.kernel.org [3.14]
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The dev->struct_mutex locking in drm_irq.c only protects
dev->irq_enabled. Which isn't really much at all and only prevents
especially nasty ums userspace from concurrently installing the
interrupt handling a few times. Or at least trying.
There are tons of unlocked readers of dev->irqs_enabled in the vblank
wait code (and by extension also in the pageflip code since that uses
the same vblank timestamp engine).
Real modesetting drivers should ensure that nothing can go haywire
with a sane setup teardown sequence. So we only really need this for
the drm_control ioctl, everywhere else this will just paper over
nastiness.
Note that drm/i915 is a bit specially due to the gem+ums combination.
So there we also need to properly protect the entervt and leavevt
ioctls. But it's definitely saner to do everything in one go than to
drop the lock in-between.
Finally there's the gpu reset code in drm/i915. That one's just race
(concurrent userspace calls to for vblank waits of pageflips could
spuriously fail). So wrap it up in with a nice comment since fixing
this is more involved.
v2: Rebase and fix commit message (Thierry)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some i2c fixes over DisplayPort.
* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: Improve vramlimit module param documentation
drm/radeon: fix audio pin counts for DCE6+ (v2)
drm/radeon/dp: switch to the common i2c over aux code
drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
drm/i915: support address only i2c-over-aux transactions
drm/tegra: dp: Support address-only I2C-over-AUX transactions
The pipe is off at that point in time, so a vblank wait is simply a
50ms wait. Caught by Jesse's verbose "make vblank wait timeouts WARN"
patch. We've probably had a few versions of this float around already.
To document assumptions put a pipe assert into the same place. And
also add a posting read.
If we ever decide to update the eld and infoframes while the pipe is
already on (e.g. for fastboot) then there's lots of work to do. So
better properly document all the hidden assumptions.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some fixes from Intel.
* tag 'drm-intel-fixes-2014-04-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Always use kref tracking for all contexts.
drm/i915: do not setup backlight if not available according to VBT
drm/i915: check VBT for supported backlight type
drm/i915: Disable self-refresh for untiled fbs on i915gm
drm/mm: Don't WARN if drm_mm_reserve_node
We already do this for HSW, but doing it makes sense for everything else
as well. Extend it for ILK/SNB/IVB since that's where the new watermark
code is used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
[danvet: Resolve conflict since I've plucked this out of the middle of
Ville's series.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like on hsw/bdw the pipe isn't actually running yet at this point.
This holds for both pch ports and the cpu edp port according to my
testing on ilk, snb and ivb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This cleans up the checkpatch errors for the merged commit -
commit d3b542fcfc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Mon Apr 14 11:00:34 2014 +0530
drm/i915: Add parsing support for new MIPI blocks in VBT
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When linking the i2c sysfs file into the connector's directory
pass directory and link target in the right order.
This code was introduced with:
commit 931c1c2698
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Feb 11 17:12:51 2014 +0200
drm/i915: sdvo: add i2c sysfs symlink to the connector's directory
This is the same what we do for DP connectors, so make things more
consistent.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The parser extracts the config block(#52) and sequence(#53) data
and store in private data structures.
v2: Address review comments by Jani
- adjust code for the structure changes for bdb_mipi_config
- add boundry and buffer overflow checks as suggested
- use kmemdup instead of kmalloc and memcpy
v3: More strict check while parsing VBT
- Ensure that at anytime we do not go beyond sequence block
while parsing
- On unknown element fail the whole parsing
v4: Style changes and spell check mostly as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we really only need this when the pfit is enabled, at least
I couldn't dicern any difference here. Furthermore the hacks we have
to reconstruct this bit is a bit glaring, and probably only works
because we can't move the lvds port to any other pipe than pipe B on
gen2/3.
So let's just rip this out.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77137 (the LVDS
WARNING log, not the main "VGA can't be turned on" issue).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we always initialize kref for the context, even if we are using fake
contexts for hangstats when there is no hw support, we can forgo the
dance to dereference the ctx->obj and inspect whether we are permitted
to use kref inside i915_gem_context_reference() and _unreference().
My ulterior motive here is to improve the debugging of a use-after-free
of ctx->obj. This patch avoids the dereference here and instead forces
the assertion checks associated with kref.
v2: Refactor the fake contexts to being even more like the real
contexts, so that there is much less duplicated and special case code.
v3: Tweaks.
v4: Tweaks, minor.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[Jani: tiny change to backport to drm-intel-fixes.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some machines use an external EC for controlling the backlight. Info
about this is present in the VBT. Do not setup native backlight control
if no PWM backlight is available or supported according to VBT. The
acpi_backlight interface appears to work for the EC control.
In most cases there has been no harm done, but it looks like there are
machines out there that have both an EC and our PWM line connected to
the same wire. This, obviously, does not end well.
This should fix the regression caused by
commit bc0bb9fd1c
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:14:29 2013 +0200
drm/i915: remove QUIRK_NO_PCH_PWM_ENABLE
AFAICT the quirk removed by the above commit effectively resulted in
i915 not driving the backlight PWM output, thus not messing things up.
Additionally this should fix the regression caused by
commit fbc9fe1b4f
Author: Aaron Lu <aaron.lu@intel.com>
Date: Fri Oct 11 21:27:45 2013 +0800
ACPI / video: Do not register backlight if win8 and native interface exists
which left some machines without a functioning backlight interface.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76276
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=62281
CC: Aaron Lu <aaron.lu@intel.com>
CC: Eric Griffith <EGriffith92@gmail.com>
CC: Kent Baxley <kent.baxley@canonical.com>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The only supported types are none and PWM. Other values are obsolete or
reserved, don't add them.
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a requirement added to the spec. This patch will prevent
persistent corruption on the display.
v2: Make the wait before the vblank wait. (Art)
Try to finish early by polling the register
s/present/prevent (Chris)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Upgrade debug output to ERROR.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch computes and stored 2nd M/N/TU for switching to different
refresh rate dynamically. PIPECONF_EDP_RR_MODE_SWITCH bit helps toggle
between alternate refresh rates programmed in 2nd M/N/TU registers.
v2: Daniel's review comments
Computing M2/N2 in compute_config and storing it in crtc_config
v3: Modified reference to edp_downclock and edp_downclock_avail based on the
changes made to move them from dev_private to intel_panel.
v4: Modified references to is_drrs_supported based on the changes made to
rename it to drrs_support.
v5: Jani's review comments
Removed superfluous return statements. Changed support for Gen 7 and above.
Corrected indentation. Re-structured the code which finds crtc and connector
from encoder. Changed some logs to be less verbose.
v6: Modifying i915_drrs to include only intel connector as intel_dp can be
derived from intel connector when required.
v7: As per internal review comments, acquiring mutex just before accessing
drrs RR. As per Chris's review comments, added documentation about the use
of locking in the function.
v8: Incorporated Jani's review comments.
Removed reference to edp_downclock.
v9: Jani's review comments. Modified comment in set_drrs. Changed index to
type edp_drrs_refresh_rate_type. Check if PSR is enabled before setting
registers fo DRRS.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch and finds out the lowest refresh rate supported for the resolution
same as the fixed_mode.
It also checks the VBT fields to see if panel supports seamless DRRS or not.
Based on above data it marks whether eDP panel supports seamless DRRS or not.
This information is needed for supporting seamless DRRS switch for certain
power saving usecases. This patch is tested by enabling the DRM logs and
user should see whether Seamless DRRS is supported or not.
v2: Daniel's review comments
Modified downclock deduction based on intel_find_panel_downclock
v3: Chris's review comments
Moved edp_downclock_avail and edp_downclock to intel_panel
v4: Jani's review comments.
Changed name of the enum edp_panel_type to drrs_support type.
Change is_drrs_supported to drrs_support of type enum drrs_support_type.
v5: Incorporated Jani's review comments
Modify intel_dp_drrs_initialize to return downclock mode. Support for Gen7
and above.
v6: Incorporated Chris's review comments.
Changed initialize to init in intel_drrs_initialize
v7: Incorporated Jani's review comments.
Removed edp_downclock and edp_downclock_avail. Return NULL explicitly.
Make drrs_state and unnamed struct. Move Gen based check inside drrs_init.
v8: Made changes to track PSR enable/disable throughout system use (instead
of just in the init sequence) for disabling/enabling DRRS. Jani's review
comments.
v9: PSR tracking will be done as part of idleness detection patch. Removed
PSR state tracker in i915_drrs. Jani's review comments.
v10: Added log for DRRS not supported in drrs_init
v11: Modification in drrs_init. suggested by Jani
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently it doesn't work. X-tiled self-refresh works flawlessly
otoh. Apparently X still works correctly with linear framebuffers, so
might just be an issue with the initial modeset. It's unclear whether
this just borked wm setup from our side or a hw restriction, but just
disabling gets things going.
Note that this regression was only brought to light with
commit 3f2dc5ac05
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Jan 10 14:06:47 2014 +0200
drm/i915: Fix 915GM self-refresh enable/disable
before that self-refresh for i915GM didn't work at all.
Kudos to Ville for spotting a little bug in the original patch I've
attached to the bug.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76103
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: rebase on top of drm-next with primary plane support.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 4b28a1f3ef.
This patch duct-tapes over some issue in the current bdw rps patches
which must wait with enabling rc6/rps until the very first batch has
been submitted by userspace.
But those patches aren't merged yet, and for upstream we need to have
an in-kernel emission of the very first batch. I shouldn't have
merged this patch so let's revert it again.
Also Imre noticed that even when rps is set up normally there's a
small window (due to the 1s delay of the async rps init work) where we
could runtime suspend already and blow up all over the place. Imre has
a proper fix to block runtime pm until the rps init work has
successfully completed.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We will treat Cherryview like Valleyview for most parts. Add a macro
for cases when we need to tell the two apart.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some MIPI panels might not have resolution which is a multiple of 64 like
1366x768. Enable this feature for such panels by default
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Though HS mode also should work.
v2: Change parameter as "bool hs" as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for Generic driver
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise, this can stall pipe. We also need DPLL REFA always
enabled
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per the hw team's recommendation we need to enable the MIPI port
before enabling the plane and pipe. So call MIPI port enable in
pre_enable phase itself
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are additional registers needed for performance monitoring and
ARB_draw_indirect extensions in mesa.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76719
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Squash in fixup from Brad requested by Ken.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
haswell_write_eld() is also used on broadwell, so let's not explicitely
mention Haswell. The rest of the function has plenty of debug output
which will print the function name, so we know where we are anyway.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is now clear that this interrupt is for the primary plane and not
something global to the pipe. It also matches what the spec calls it.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Piglit runner and QA are both looking at the dmesg for
DRM_ERRORs with test cases. Add a flag to control those
when we they are expected from related test cases.
Also add flag to control if contexts should be banned
that introduced the hang. Hangcheck is timer based and
preventing bans by adding sleeps to testcases makes
testing slower.
v2: intel_ring_stopped(), readable comment (Chris)
v3: keep compatibility (Daniel)
References: https://bugs.freedesktop.org/show_bug.cgi?id=75876
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since dma_buf_vunmap() procedes blithely on ignorant of whether the
driver failed to actually unmap the backing storage for the dma-buf, we
need to make a best-effort to do so. This involves not allowing
ourselves to be susceptible to signals causing us to leak the storage.
This should have been detectable with the current i-g-t as a misplaced
signal should have left the pages pinned upon freeing the object where
we have a warning in place.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Comment from Ben: It's a bit unclear whether we need this dance still
on bdw.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8 now has a qword to code for 48bit addresses.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems like it wouldn't be too unlikely to be wanting to use a an
expression in the macro argument and things could go very wrong.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needs to happen after clock is running or it doesn't behave correctly.
v2: fix subject (Ville)
make it clearer that this occurs in pre_enable (Paulo)
misc bikesheds (Paulo)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allows sending of the null packets for conformance.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We also do a disable later when we write a specific infoframe, but here
we do it to prevent sending a stale one before updating the infoframes.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we end up bouncing these around between ports.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We will have another use for the maximum watermark values that the
registers can hold. Pull those out into separate functions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even though the inactive pipes should have their watermarks set to all 0
with enable=true, we can possibly shave off a few cycles by completely
skipping the merge procedure for inactive pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_pipe_wm will be used to track the state in different stages
of the watermark update process. For that we need to keep a bit
more state in intel_pipe_wm.
We also need to separate the multi-pipe intel_wm_config computation
from ilk_compute_wm_parameters() as that one deals with the future
state, and we need the intel_wm_config to match the current hardware
state at the time we do the watermark merging for multiple pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Frob conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we've learned over time, the HW context is just a series of GPU
commands that we're able to decode without any changes in
intel_error_decode. Since many bugs recently have been implicated in
the HW context state, it makes sense to dump the whole context object
in a form which can be parsed.
Sample:
render ring --- HW Context = 0x042db000
ringbuffer (render ring) at 0x0160c000; HEAD points to: 0x0160c000
0x0160c000: 0x00000000: MI_NOOP
0x0160c004: 0x00000000: MI_NOOP
0x0160c008: 0x00000000: MI_NOOP
0x0160c00c: 0x00000000: MI_NOOP
0x0160c010: 0x00000000: MI_NOOP
0x0160c014: 0x00000000: MI_NOOP
0x0160c018: 0x00000000: MI_NOOP
0x0160c01c: 0x00000000: MI_NOOP
Unfortunately, our decoder isn't quite smart enough to deal with the
variable length LRIs - but that is a tools problem.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Clarify commit message a bit, seems to have lost a few
crucial words.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I opted to do this instead of grabbing the context reference after
eb_create since eb_create can potentially call the shrinker, and that
makes things very complicated. This simple patch balances the ref count
without requiring a great deal of review to make sure the shrinker path
is safe.
Theoretically (by design) the shrinker can end up destroying a context,
which enforces the reasoning for doing the fix this way instead of
moving the reference to later in the function.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sprite LP2+ registers don't exist on ILK/SNB so don't read them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't do CPU access to GPU contexts so making the GPU access snoop
the CPU caches seems silly, and potentially expensive.
v2: Use !IS_VALLEYVIEW instead of HAS_LLC as this is really
about what the PTEs can represent.
Add a comment clarifying the situation.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Gen4+ platforms (except BDW), Render Cache Operational flush
cannot be enabled.
This WA is apparently required for all Gen4+ platforms,except BDW.
In BDW, the bit has been repurposed otherwise.
This has been tested only on vlv.
v2: Corrected the code regarding the wrong usage of
MASKED_BIT_DISABLE (Chris)
v3: Enhancing the scope of WA to Gen4+ platforms except BDW (Ville)
v4: Adding WA for g4x, crestline, broadwater (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next after the big s/crtc->fb/crtc->primary->fb/
cocinelle patch to avoid endless amounts of conflict hilarity in my
-next queue for 3.16.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge window -fixes pull request as usual. Well, I did sneak in Jani's
drm_i915_private_t typedef removal, need to have fun with a big sed job
too ;-)
Otherwise:
- hdmi interlaced fixes (Jesse&Ville)
- pipe error/underrun/crc tracking fixes, regression in late 3.14-rc (but
not cc: stable since only really relevant for igt runs)
- large cursor wm fixes (Chris)
- fix gpu turbo boost/throttle again, was getting stuck due to vlv rps
patches (Chris+Imre)
- fix runtime pm fallout (Paulo)
- bios framebuffer inherit fix (Chris)
- a few smaller things
* tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel: (196 commits)
Skip intel_crt_init for Dell XPS 8700
drm/i915: vlv: fix RPS interrupt mask setting
Revert "drm/i915/vlv: fixup DDR freq detection per Punit spec"
drm/i915: move power domain init earlier during system resume
drm/i915: Fix the computation of required fb size for pipe
drm/i915: don't get/put runtime PM at the debugfs forcewake file
drm/i915: fix WARNs when reading DDI state while suspended
drm/i915: don't read cursor registers on powered down pipes
drm/i915: get runtime PM at i915_display_info
drm/i915: don't read pp_ctrl_reg if we're suspended
drm/i915: get runtime PM at i915_reg_read_ioctl
drm/i915: don't schedule force_wake_timer at gen6_read
drm/i915: vlv: reserve the GT power context only once during driver init
drm/i915: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/overlay: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/ringbuffer: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/display: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/irq: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/gem: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t
...
Daniel Vetter