The patch add basic support for the quad spi controller.
QSPI is a kind of spi module that allows single,
dual and quad read access to external spi devices. The module
has a memory mapped interface which provide direct interface
for accessing data form external spi devices.
The patch will configure controller clocks, device control
register and for defining low level transfer apis which
will be used by the spi framework to transfer data to
the slave spi device(flash in this case).
Test details:
-------------
Tested this on dra7 board.
Test1: Ran mtd_stesstest for 40000 iterations.
- All iterations went through without failure.
Test2: Use mtd utilities:
- flash_erase to erase the flash device
- mtd_debug read to read data back.
- mtd_debug write to write to the data flash.
diff between the write and read data shows zero.
Acked-by: Felipe Balbi<balbi@ti.com>
Reviewed-by: Felipe Balbi<balbi@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Expand the arm64 image header to allow for co-existance with
PE/COFF header required by the EFI stub. The PE/COFF format
requires the "MZ" header to be at offset 0, and the offset
to the PE/COFF header to be at offset 0x3c. The image
header is expanded to allow 2 instructions at the beginning
to accommodate a benign intruction at offset 0 that includes
the "MZ" header, a magic number, and the offset to the PE/COFF
header.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the document for DSPI driver under
Documentation/devicetree/bindings/spi/.
Signed-off-by: Chao Fu <b44548@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds ac97-slave support.
For ac97, the registers have to be setup earlier than for other ssi
modes because there is some communication with the external device
before streaming. So this patch introduces a fsl_ssi_setup function to
setup the registers for different ssi operation modes seperately.
This patch was tested with imx27-pca100.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch implements a device-tree-only CPU DAI driver for Freescale
S/PDIF controller that supports stereo playback and record feature.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These patches add machine support for the Allwinner A20 and A31 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MCmi
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.12-2' of https://github.com/mripard/linux into next/soc
Allwinner sunXi core additions for 3.12, take 2
These patches add machine support for the Allwinner A20 and A31 SoCs
* tag 'sunxi-core-for-3.12-2' of https://github.com/mripard/linux:
ARM: sunxi: Introduce Allwinner A20 support
ARM: sun6i: Add restart code for the A31
ARM: sunxi: Add the Allwinner A31 compatible to the machine definition
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ve9i
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
MAINTAINERS: Add myself as Tegra PCIe maintainer
PCI: tegra: set up PADS_REFCLK_CFG1
PCI: tegra: Add Tegra 30 PCIe support
PCI: tegra: Move PCIe driver to drivers/pci/host
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: tegra: add LP1 suspend support for Tegra114
ARM: tegra: add LP1 suspend support for Tegra20
ARM: tegra: add LP1 suspend support for Tegra30
ARM: tegra: add common LP1 suspend support
clk: tegra114: add LP1 suspend/resume support
ARM: tegra: config the polarity of the request of sys clock
ARM: tegra: add common resume handling code for LP1 resuming
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
ARM: tegra: unify Tegra's Kconfig a bit more
ARM: tegra: remove the limitation that Tegra114 can't support suspend
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
No functional changes. This patch fixes the post gcwq comments in
Documentation/workqueue.txt.
tj: Whitespace adjustments. Minor updates.
Signed-off-by: Libin <huawei.libin@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add irqchip driver for the ImgTec PowerDown Controller (PDC) as found in
the TZ1090. The PDC has a number of general system wakeup (SysWake)
interrupts (which would for example be connected to a power button or an
external peripheral), and a number of peripheral interrupts which can
also wake the system but are connected straight to specific low-power
peripherals (such as RTC or Infrared). It has a single interrupt output
for SysWakes, and individual interrupt outputs for each peripheral.
The driver demuxes the SysWake interrupt line, and passes the peripheral
interrupts straight through. It also handles the set_wake interrupt
operation to enable/disable the appropriate wake event bits.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: linux-metag@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
* Support for memory mapped arch_timers
* Trivial fixes to the moxart timer code
* Documentation updates
Trivial conflicts in drivers/clocksource/arm_arch_timer.c. Fixed up
the newly added __cpuinit annotations as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some boards require custom PHY configuration, for example due to trace
length differences. Add the ability to configure these registers in
order to get the PHY to function on boards that need it.
Because PHYs are auto-detected based on MDIO device IDs, allow PHY
configuration to be specified in the parent Ethernet device node if no
PHY device node is present.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This branch contains all *.dts (device tree) changes for Tegra.
New features enabled are:
* PMICs on Dalmore
* CPU power-gating on Dalmore
* HDMI output on Beaver
* LP1 system suspend mode on almost all boards
* PCIe support on numerous Tegra20/30 boards
* USB support on Tegra30/114 boards
* Audio capture on Beaver and Dalmore
* Temperature sensor on Cardhu.
... along with a few DT cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RGgU
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.12-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From: Stephen Warren:
ARM: tegra: device tree changes for 3.12
This branch contains all *.dts (device tree) changes for Tegra.
New features enabled are:
* PMICs on Dalmore
* CPU power-gating on Dalmore
* HDMI output on Beaver
* LP1 system suspend mode on almost all boards
* PCIe support on numerous Tegra20/30 boards
* USB support on Tegra30/114 boards
* Audio capture on Beaver and Dalmore
* Temperature sensor on Cardhu.
... along with a few DT cleanups.
* tag 'tegra-for-3.12-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (25 commits)
ARM: tegra: add Mic Jack to Dalmore device tree
ARM: tegra: add Mic Jack to Beaver device tree
ARM: tegra: add USB DT entries for Tegra114, Dalmore
ARM: tegra: add USB DT entries for Tegra30
ARM: dts: tegra: Increase prefetchable PCI memory space
ARM: tegra: Fix Beaver's PCIe lane configuration
ARM: tegra: Enable PCIe controller on Beaver
ARM: tegra: Enable PCIe controller on Cardhu
ARM: tegra: Add Tegra30 PCIe support
ARM: tegra: trimslice: Initialize PCIe from DT
ARM: tegra: harmony: Initialize PCIe from DT
ARM: tegra: tec: Add PCIe support
ARM: tegra: tamonten: Add PCIe support
ARM: tegra: Add Tegra20 PCIe support to DT
ARM: tegra: enable LP1 suspend mode
ARM: tegra: beaver: Enable HDMI output
ARM: tegra: use TEGRA_GPIO() in a couple more places
ARM: tegra: dalmore: fix the irq trigger type of Palmas MFD device
ARM: tegra: define valid function names in DT document
ARM: tegra: dalmore: add PM configurations for PMC
...
development cycle:
- Various cleanups like remove non-existant hardware from
the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Wm2y
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From: Linus Walleij:
Ux500 device tree enablement base for the v3.12
development cycle:
- Various cleanups like remove non-existant hardware from
the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT
* tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (22 commits)
ARM: ux500: fix devicetree builds
ARM: ux500: Remove u9540.dts as it's been replaced
ARM: ux500: Apply a ste-* prefix onto dbx5x0.dtsi
ARM: ux500: Apply a ste-* prefix onto stuib.dtsi
ARM: ux500: Apply a ste-* prefix onto hrefv60plus.dts
ARM: ux500: Apply a ste-* prefix onto hrefprev60.dts Signed-off-by: Lee Jones <lee.jones@linaro.org>
ARM: ux500: Apply a ste-* prefix onto href.dtsi
ARM: ux500: Apply a ste-* prefix onto ccu9540.dts
ARM: ux500: Apply a ste-* prefix onto ccu8540.dts
ARM: ux500: Apply a ste-* prefix onto snowball.dts
ARM: ux500: Remove Snowball DTS entry for ROHM BH1780GLI ambient light sensor
ARM: ux500: Remove Snowball DTS entry for TPS61052 chip
ARM: ux500: Remove Snowball DTS entry for National Semiconductor LP5521 LED chip
ARM: ux500: Remove Toshiba TC35892 I/O Expander's DT entry from Snowball's DTS
ARM: u8540: DT: Set pinctrl mapping to i2c0,1,2,4 & 5
ARM: u8540: Add Pinctrl Device Tree settings for uart0, uart2
ARM: ux500: Stop passing MMC's platform data for Device Tree boots
Documentation: Update binding for Nomadik and DBx5x based platforms
ARM: ux500: Supply external regulator names for Snowball's DT
ARM: ux500: Provide a supply name for the AB8500 AUX regulators to use
...
Conflicts:
net/netfilter/nf_conntrack_proto_tcp.c
The conflict had to do with overlapping changes dealing with
fixing the use of an "s32" to hold the value returned by
NAT_OFFSET().
Pablo Neira Ayuso says:
====================
The following batch contains Netfilter/IPVS updates for your net-next tree.
More specifically, they are:
* Trivial typo fix in xt_addrtype, from Phil Oester.
* Remove net_ratelimit in the conntrack logging for consistency with other
logging subsystem, from Patrick McHardy.
* Remove unneeded includes from the recently added xt_connlabel support, from
Florian Westphal.
* Allow to update conntracks via nfqueue, don't need NFQA_CFG_F_CONNTRACK for
this, from Florian Westphal.
* Remove tproxy core, now that we have socket early demux, from Florian
Westphal.
* A couple of patches to refactor conntrack event reporting to save a good
bunch of lines, from Florian Westphal.
* Fix missing locking in NAT sequence adjustment, it did not manifested in
any known bug so far, from Patrick McHardy.
* Change sequence number adjustment variable to 32 bits, to delay the
possible early overflow in long standing connections, also from Patrick.
* Comestic cleanups for IPVS, from Dragos Foianu.
* Fix possible null dereference in IPVS in the SH scheduler, from Daniel
Borkmann.
* Allow to attach conntrack expectations via nfqueue. Before this patch, you
had to use ctnetlink instead, thus, we save the conntrack lookup.
* Export xt_rpfilter and xt_HMARK header files, from Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, rcutorture has separate torture_types to test synchronous,
asynchronous, and expedited grace-period primitives. This has
two disadvantages: (1) Three times the number of runs to cover the
combinations and (2) Little testing of concurrent combinations of the
three options. This commit therefore adds a pair of module parameters
that control normal and expedited state, with the default being both
types, randomly selected, by the fakewriter processes, thus reducing
source-code size and increasing test coverage. In addtion, the writer
task switches between asynchronous-normal and expedited grace-period
primitives driven by the same pair of module parameters.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
[ this is a follow-up to this discussion:
http://archive.arm.linux.org.uk/lurker/message/20130730.230827.a1ceb12a.en.html ]
This patchset renames all uses of "bcm," name bindings to
"brcm," as they were done prior to knowing that brcm had
already been standardized as Broadcom vendor prefix
(in Documentation/devicetree/bindings/vendor-prefixes.txt).
This will not cause any churn on devices because none of
these bindings have made it into production yet.
Also rename the the following dt binding docs that had "bcm,"
in their name for consistency:
- bcm,kona-sdhci.txt -> kona-sdhci.txt
- bcm,kona-timer.txt -> kona-timer.txt
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
smp_affinity holds bitmask and smp_affinity_list holds list. So we
should write a list to smp_affinity_list, instead of smp_affinity.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Request inclusion of oneline summaries when referring to other commits
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add devm_iio_device_alloc() and devm_iio_device_free() functions
to list of supported calls.
Signed-off-by: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
> docproc: kernel/printk.c: No such file or directory
So rename the file.
Signed-off-by: Joe Perches <joe@perches.com>
Noticed-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section. Fix
the example code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section. Fix
the examples.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Fix the example.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix a typo, and the reference to a proposed v2.7 kernel, as
that in itself is dated.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected the word beteween to between in the file rs485.txt.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected the word MAITAINERS to MAINTAINERS.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected the word Configuraion to Configuration in the file dscr.txt.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected the word ponter to pointer.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected the word negtive to negative.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected the word avarage to average in the file compress_offload.txt.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected the word configation to configuration.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected the word adventerous to adventurous.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected the word osciallator to oscillator in the file st,nomadik.txt.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected the word compatbile to compatible in the file atmel-can.txt.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Until today all gamepad input drivers report their data differently. It is
nearly impossible to write applications for more than one device in a
generic way. Therefore, this patch introduces a uniform gamepad API which
will be used for all new drivers.
Instead of mapping buttons by their labels, we now map them by position.
This allows applications to work with any gamepad regardless of the labels
on the buttons. Furthermore, we standardize the ABS_* codes for analog
triggers and sticks.
For D-Pads the long overdue BTN_DPAD_* codes are introduced. They should
be fairly obvious how to use. To avoid confusion, the action buttons now
have BTN_EAST/SOUTH/WEST/NORTH aliases.
Reported-by: Todd Showalter <todd@electronjump.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds generic ac97 reset functions using pincontrol and gpio
parsed from devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Each control-dependency example needs its barriers between the "if"
condition and the body of the "if" because a control dependency is
a dependency induced by a branch. This commit makes the needed
adjustment.
Reported-by: Yongming Shen <symingz@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Note that this commit also updates the formatting of serveral of the
bibtex entries to conform to that of my .bib files. I started
accumulating entries back in the 1980s, back when bibtex insisted
that comma (",") was a separator, not a terminator. This rule forced
commas to the fronts of lines. 25 years later, bibtex allows commas
to be terminators, but I am too lazy to rework all my .bib files.
Keeping the same format as my .bib files allows my to simply
incorporate my RCU.bib file into Documentation/RCU/RTFP.txt, which
is much easier than my earlier practice of keeping track of what
had changed and adding individual entries. (I sometimes find relevant
papers that were published some years back, for example.)
In addition, this change adds entries for papers published in the
last year or so.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
[ this is a follow-up to this discussion:
http://archive.arm.linux.org.uk/lurker/message/20130730.230827.a1ceb12a.en.html ]
This patchset renames all uses of "bcm," name bindings to
"brcm," as they were done prior to knowing that brcm had
already been standardized as Broadcom vendor prefix
(in Documentation/devicetree/bindings/vendor-prefixes.txt).
This will not cause any churn on devices because none of
these bindings have made it into production yet.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add core support to allow clock implementations to select the best
parent clock when rounding a rate, e.g. the one which can provide the
closest clock rate to that requested. This is by way of adding a new
clock op, determine_rate(), which is like round_rate() but has an extra
parameter to allow the clock implementation to optionally select a
different parent clock. The core then takes care of reparenting the
clock when setting the rate.
The parent change takes place with the help of some new private data
members. struct clk::new_parent specifies a clock's new parent (NULL
indicates no change), and struct clk::new_child specifies a clock's new
child (whose new_parent member points back to it). The purpose of these
are to allow correct walking of the future tree for notifications prior
to actually reparenting any clocks, specifically to skip child clocks
who are being reparented to another clock (they will be notified via the
new parent), and to include any new child clock. These pointers are set
by clk_calc_subtree(), and the new_child pointer gets cleared when a
child is actually reparented to avoid duplicate POST_RATE_CHANGE
notifications.
Each place where round_rate() is called, determine_rate() is checked
first and called in preference. This restructures a few of the call
sites to simplify the logic into if/else blocks.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BR17
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Minimal DRA7xx based SoC core support via Rajendra Nayak <rnayak@ti.com>
* tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (849 commits)
ARM: DRA7: Add the build support in omap2plus
ARM: DRA7: hwmod: Reuse the soc_ops used for OMAP4/5
ARM: DRA7: id: Add cpu detection support for DRA7xx based SoCs'
ARM: DRA7: Kconfig: Make ARCH_NR_GPIO default to 512
ARM: DRA7: board-generic: Add basic DT support
ARM: DRA7: Resue the clocksource, clockevent support
ARM: DRA7: Reuse io tables and add a new .init_early
ARM: DRA7: Reuse all of PRCM and MPUSS SMP infra
Linux 3.11-rc5
btrfs: don't loop on large offsets in readdir
Btrfs: check to see if root_list is empty before adding it to dead roots
Btrfs: release both paths before logging dir/changed extents
Btrfs: allow splitting of hole em's when dropping extent cache
Btrfs: make sure the backref walker catches all refs to our extent
Btrfs: fix backref walking when we hit a compressed extent
Btrfs: do not offset physical if we're compressed
Btrfs: fix extent buffer leak after backref walking
Btrfs: fix a bug of snapshot-aware defrag to make it work on partial extents
btrfs: fix file truncation if FALLOC_FL_KEEP_SIZE is specified
dlm: kill the unnecessary and wrong device_close()->recalc_sigpending()
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
It has way too much potential for driver writers to do stupid things
like delayed hw setup because the load sequence is somehow racy (e.g.
the imx driver in staging). So don't call it for modesetting drivers,
which reduces the complexity of the drm core -> driver interface a
notch.
v2: Don't forget to update DocBook.
v3: Go with Laurent's slightly more elaborate proposal for the DocBook
update. Add a few words on top of his diff to elaborate a bit on what
KMS drivers should and shouldn't do in lastclose. There was already a
paragraph present talking about restoring properties, I've simply
extended that one.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I've forgotten this and shuffling all the little pieces into the
respective patches is rather cumbersome ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit adds information about testing nohz_full, and also emphasizes
the fact that you need a multi-CPU system to get any benefit from nohz_full.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
A small helper to queue up work to do, from workqueue context, after a
flip. Typically useful to defer unreffing buffers that may be read by
the display controller until vblank.
v1: original
v2: wire up docbook + couple docbook fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There was a time when rcu_barrier() was guaranteed to wait for at least
a grace period, but that time ended due to energy-efficiency concerns.
So now rcu_barrier() is a no-op if there are no RCU callbacks queued in
the system. This commit updates the documentation to reflect this change.
Now, rcu_barrier() often does wait for a grace period, so, one could
imagine some modification to rcu_barrier() to more efficiently handle
cases where both rcu_barrier() and a grace period are needed. But this
must wait until someone shows a real-world need for a change.
Reported-by: Bob Copeland <bob@cozybit.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
So I've stumbled over drm_fasync and wondered what it does. Digging
that up is quite a story.
First I've had to read up on what this does and ended up being rather
bewildered why peopled loved signals so much back in the days that
they've created SIGIO just for that ...
Then I wondered how this ever works, and what that strange "No-op."
comment right above it should mean. After all calling the core fasync
helper is pretty obviously not a noop. After reading through the
kernels FASYNC implementation I've noticed that signals are only sent
out to the processes attached with FASYNC by calling kill_fasync.
No merged drm driver has ever done that.
After more digging I've found out that the only driver that ever used
this is the so called GAMMA driver. I've frankly never heard of such a
gpu brand ever before. Now FASYNC seems to not have been the only bad
thing with that driver, since Dave Airlie removed it from the drm
driver with prejudice:
commit 1430163b4bbf7b00367ea1066c1c5fe85dbeefed
Author: Dave Airlie <airlied@linux.ie>
Date: Sun Aug 29 12:04:35 2004 +0000
Drop GAMMA DRM from a great height ...
Long story short, the drm fasync support seems to be doing absolutely
nothing. And the only user of it was never merged into the upstream
kernel. And we don't need any fops->fasync callback since the fcntl
implementation in the kernel already implements the noop case
correctly.
So stop this particular cargo-cult and rip it all out.
v2: Kill drm_fasync assignments in rcar (newly added) and imx drivers
(somehow I've missed that one in staging). Also drop the reference in
the drm DocBook. ARM compile-fail reported by Rob Clark.
v3: Move the removal of dev->buf_asnyc assignment in drm_setup to this
patch here.
v4: Actually git add ... tsk.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge the rcar stable branch that is being shared with the arm-soc tree.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* pfdo/drm-rcar-for-v3.12: (220 commits)
drm/rcar-du: Add FBDEV emulation support
drm/rcar-du: Add internal LVDS encoder support
drm/rcar-du: Configure RGB output routing to DPAD0
drm/rcar-du: Rework output routing support
drm/rcar-du: Add support for DEFR8 register
drm/rcar-du: Add support for multiple groups
drm/rcar-du: Fix buffer pitch alignment for R8A7790 DU
drm/rcar-du: Add support for the R8A7790 DU
drm/rcar-du: Move output routing configuration to group
drm/rcar-du: Remove register definitions for the second channel
drm/rcar-du: Use dynamic number of CRTCs instead of CRTCs array size
drm/rcar-du: Introduce CRTCs groups
drm/rcar-du: Rename rcar_du_plane_(init|register) to rcar_du_planes_*
drm/rcar-du: Create rcar_du_planes structure
drm/rcar-du: Rename platform data fields to match what they describe
drm/rcar-du: Merge LVDS and VGA encoder code
drm/rcar-du: Split VGA encoder and connector
drm/rcar-du: Split LVDS encoder and connector
drm/rcar-du: Clarify comment regarding plane Y source coordinate
drm/rcar-du: Support per-CRTC clock and IRQ
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/qxl/qxl_release.c
MFC driver is updated to use only one clock instead of
two. Correcting this in the binding documentation.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sample code erroneously scales the y1, pb and pr variables from the
[0.0 .. 1.0] and [-0.5 .. 0.5] ranges to [0 .. 255] and [-128 .. 127].
Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Clarify that the il_vfrontporch, il_vsync and il_vbackporch fields must
always be 0 for progressive formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
NV16M and NV61M are planar YCbCr 4:2:2 and YCrCb 4:2:2 formats with a
luma plane followed by an interleaved chroma plane. The planes are not
required to be contiguous in memory, and the formats can only be used
with the multi-planar formats API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The V4L2_MBUS_FMT_YUV10_1X30 code is documented as being equal to
0x2014, while the v4l2-mediabus.h header defines it as 0x2016. Fix the
documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VIDIOC_CREATE_BUFS ioctl takes a format argument that must contain a
valid format supported by the driver. Clarify the documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The patch modifies the helper function v4l2_ctrl_new_std_menu
to accept integer menu controls with standard menu items.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds variant data and core support for the MFC v7 firmware
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a resource managed devm_iio_trigger_alloc()/devm_iio_triger_free()
to automatically clean up triggers allocated by IIO drivers, thus
leading to simplified IIO drivers code.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyunmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Allwinner A31 has a different watchdog, with a slightly different
register layout, that requires a different restart code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- MBus devicetree bindings
- devbus update for address decoding window, cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSC9AMAAoJEAi3KVZQDZAeEskH+gLbu4awN//ItLxqdOjCffs1
o3N7C21SjAuGrueSxLFcYxLXk6XhM1x3mAEjvvbd1ze1yyKIY21PQGkwtjrxQxr5
DbRtz8slgFte9jnOtUQ9gfSM8Q4PsOT4oPtj6tFc9DREIhX8uZtDxLn5YVNsD1MI
hLxKbL9OHUxtwQ6aM7IdyMmYXkmLVaBUZFJ7f86CH8oVRJXLcqYzVdLrOUmbRdBX
GpB6hAnSqx2spfAYxI928Od+3PIRVW4qm724t0iLI+8xQmjCxIbIDz8sS2NKVM9G
YowJ+im5dUI3Wv7l/huVi/r0mvQJJi6BL36c+O0YJUY7KeKT615zdeG3AekvB5g=
=6spO
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.12' of git://git.infradead.org/linux-mvebu into next/soc
From Jason Cooper:
mvebu drivers changes for v3.12
- MBus devicetree bindings
- devbus update for address decoding window, cleanup
* tag 'drivers-3.12' of git://git.infradead.org/linux-mvebu: (35 commits)
memory: mvebu-devbus: Remove unused variable
ARM: mvebu: Relocate PCIe node in Armada 370 RD board
ARM: mvebu: Fix AXP-WiFi-AP DT for MBUS DT binding
ARM: mvebu: add support for the AXP WiFi AP board
ARM: mvebu: use dts pre-processor for mv78230
PCI: mvebu: Adapt to the new device tree layout
bus: mvebu-mbus: Add devicetree binding
ARM: kirkwood: Relocate PCIe device tree nodes
ARM: kirkwood: Introduce MBUS_ID
ARM: kirkwood: Introduce MBus DT node
ARM: kirkwood: Use the preprocessor on device tree files
ARM: kirkwood: Split DT and legacy MBus initialization
ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes
ARM: mvebu: Relocate Armada 370/XP DeviceBus device tree nodes
ARM: mvebu: Add BootROM to Armada 370/XP device tree
ARM: mvebu: Add MBus to Armada 370/XP device tree
ARM: mvebu: Use the preprocessor on Armada 370/XP device tree files
ARM: mvebu: Initialize MBus using the DT binding
ARM: mvebu: Remove the harcoded BootROM window allocation
bus: mvebu-mbus: Factorize Armada 370/XP data structures
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds WEIM support for all i.MX CPUs supported by the kernel.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Hi Greg,
This pull request includes one new feature for the xhci-plat driver (device
tree support). Felipe was fine with the patch last I checked, but hadn't
provided an official Acked-by line.
This pull request also includes 13 patches from my FOSS Outreach Program for
Women (OPW) intern, Xenia. She fixed a bug in the xHCI driver so that the
driver can allocate 64-bit consistent DMA, converted the driver to use dynamic
debugging, and added a bunch of new trace events for the xHCI driver. The
python plugin for trace-cmd should be up on git hub shortly, although the trace
events are usable without it.
I'm very happy with the progress that Xenia has made, and I look forward to her
future contributions to the Linux kernel.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=n45I
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Platform updates, 64-bit DMA, and trace events for 3.12.
Hi Greg,
This pull request includes one new feature for the xhci-plat driver (device
tree support). Felipe was fine with the patch last I checked, but hadn't
provided an official Acked-by line.
This pull request also includes 13 patches from my FOSS Outreach Program for
Women (OPW) intern, Xenia. She fixed a bug in the xHCI driver so that the
driver can allocate 64-bit consistent DMA, converted the driver to use dynamic
debugging, and added a bunch of new trace events for the xHCI driver. The
python plugin for trace-cmd should be up on git hub shortly, although the trace
events are usable without it.
I'm very happy with the progress that Xenia has made, and I look forward to her
future contributions to the Linux kernel.
Sarah Sharp
This change makes documentation of the the gpio-ranges property shorter
and more succinct, more consistent with the style of the rest of the
document, and not mention Linux-specifics such as the API
pinctrl_request_gpio(); DT binding documents should be OS independant
where at all possible. As part of this, the gpio-ranges property's format
is described in BNF form, in order to match the rest of the document.
This change also deprecates the #gpio-range-cells property. Such
properties are useful when one node references a second node, and that
second node dictates the format of the reference. However, that is not
the case here; the definition of gpio-ranges itself always dictates its
format entirely, and hence the value #gpio-range-cells must always be 3,
and hence there is no point requiring any referenced node to include
this property. The only remaining need for this property is to ensure
compatibility of DTs with older SW that was written to support the
previous version of the binding.
v4:
* Mention #gpio-range-cells as being deprecated, rather than removing all
documentation of that property. This allows DTs to be written in a
backwards-compatible way if desired, and also allows older DTs to be
interpreted fully using the latest documentation.
v3:
* Mention BNF in commit description.
* Fixed typo.
* Dropped patch that removed the deprecated property from *.dts, since
it's required to boot older kernels.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the secondary SMBus controller on the AMD SB800 and AMD FCH
chipsets.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The bindings do not carry any resources, as the module only registers
the ASoC platform driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The pxa ssp DAI acts as a user of a pxa ssp port, and needs an
appropriate 'port' phandle in DT to reference the upstream.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a Mic Jack widget to the Tegra+RT5640 machine driver, and document
this in the DT binding. This enables the DT to include the Mic Jack in
the audio routing table, and hence enables capture of audio, in addition
to the previously-working playback.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
we defined some special properties for hardware flow control, document them
for DT-binding.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section. Fix
the examples.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SGPIO PICs don't follow the standard very well and expect a certain
number of clock cycles or port frames in each SGPIO pattern. Add two
optional parameters in the DTB that can provide the number of extra
clock cycles to be sent before and after SGPIO pattern. Read those
parameters from the DTB and send the extra clock cycles.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some board designs do not drive the SATA transmit lines within the
specification. The ECME can provide override settings, on a per board
basis, to bring the transmit lines within spec. Read those settings
from the DTB and program them in.
At the time of submission, no production hardware requires this patch.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Calxeda sata_highbank driver has been adding its descriptions to the
ahci driver. Separate them properly. This patch only affects
documentation and has no functional component.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
TI Palmas series Power Management IC have multiple pins which can be
configured for different functionality. This pins can be configured
for different function. Also their properties like pull up/down,
open drain enable/disable are configurable.
Add support for pincontrol driver Palmas series device like TPS65913,
TPS80036. The driver supports to be register from DT only.
Changes from V1:
- Add generic property for pins and functions in pinconf-generic.
- Add APIs to map the DT and subnode.
- Move common utils APIs to the pinctrl-utils from this file.
- Update the binding document accordingly.
Changes from V2:
- Add ack by Lee.
- Correct the binding docs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch contains an ugly hack for looking up the the DMA request
number. The problem here is that the implementation as it stands will
allocate the DMA channel from the user of the ssp port, and hence we
cannot allocate a real channel here.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Hook up "pm_power_off" to palmas power off routine if there is DT
property "ti,system-power-controller" defined, so platform which is
powered by this regulator can be powered off properly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds clock to list of mfd cells for s2mps11 and DT documentation
for clock part.
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit cab70040df ("net: igmp:
Reduce Unsolicited report interval to 1s when using IGMPv3") and
2690048c01 ("net: igmp: Allow user-space
configuration of igmp unsolicited report interval") by William Manley made
igmp unsolicited report intervals configurable per interface and corrected
the interval of unsolicited igmpv3 report messages resendings to 1s.
Same needs to be done for IPv6:
MLDv1 (RFC2710 7.10.): 10 seconds
MLDv2 (RFC3810 9.11.): 1 second
Both intervals are configurable via new procfs knobs
mldv1_unsolicited_report_interval and mldv2_unsolicited_report_interval.
(also added .force_mld_version to ipv6_devconf_dflt to bring structs in
line without semantic changes)
v2:
a) Joined documentation update for IPv4 and IPv6 MLD/IGMP
unsolicited_report_interval procfs knobs.
b) incorporate stylistic feedback from William Manley
v3:
a) add new DEVCONF_* values to the end of the enum (thanks to David
Miller)
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: William Manley <william.manley@youview.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Device Tree match table to xhci-plat.c. Add DT bindings document.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3NS9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.12 merge window
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/udc-core.c
drivers/usb/host/ehci-tegra.c
drivers/usb/musb/omap2430.c
drivers/usb/musb/tusb6010.c
Introduce a data structure to parameterize the driver according to SoC
generation, add Tegra30 specific code and update the device tree binding
document for Tegra30 support.
Signed-off-by: Jay Agarwal <jagarwal@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Move the PCIe driver from arch/arm/mach-tegra into the drivers/pci/host
directory. The motivation is to collect various host controller drivers
in the same location in order to facilitate refactoring.
The Tegra PCIe driver has been largely rewritten, both in order to turn
it into a proper platform driver and to add MSI (based on code by
Krishna Kishore <kthota@nvidia.com>) as well as device tree support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
[swarren, split DT changes into a separate patch in another branch]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch updates the documentation to explain the driver model
and file layout.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Proper description for Exynos4 bindings added to Documentation/devicetree/
bindings. It adds description to use multiple TMU instances, optional voltage
supply node and optional shared register across multiple TMU's.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This is based on the initial imx thermal work done by
Rob Lee <rob.lee@linaro.org> (Not sure if the email address is still
valid). Since he is no longer interested in the work and I have
rewritten a significant amount of the code, I just took the authorship
over from him.
It adds the imx thermal support using Temperature Monitor (TEMPMON)
block found on some Freescale i.MX SoCs. The driver uses syscon regmap
interface to access TEMPMON control registers and calibration data, and
supports cpufreq as the cooling device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Exynos5420 added support for I2S TDM mode. For this, there are some
register changes in the I2S controller. This patch adds the relevant
register changes to support I2S in normal mode. This patch adds a
quirk for TDM mode and if TDM mode is present all the relevent changes
will be applied.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Samsung has different versions of I2S introduced in different
platforms. Each version has some new support added for multichannel,
secondary fifo, s/w reset control and internal mux for rclk src clk.
Each newly added change has a quirk. So this patch adds all the
required quirks as driver data and based on compatible string from
dtsi fetches the quirks.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Palmas regulator SMPS10 is splitted into two regulators SMPS10-OUT1 and
SMPS10-OUT2 to match with hw behavior. With this regulator's name got
changed in driver.
Update the DT binding document to match with driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Adding a simple device tree binding for the specification of key
sequences. Definition of the keys found in the sequence are located in
'include/uapi/linux/input.h'.
For the sysrq driver, holding the sequence of keys down for a specific
amount of time will reset the system.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Describe minimal DT boot machine details for DRA7xx based SoC's. DRA7xx
family is based on dual core ARM CORTEX A15 using GIC as the interrupt controller.
The PRCM and timer infrastructure is reused from OMAP5 and so are the io
descriptor tables.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
This patch corrects unfaithful Korean translation in Documentation/ko_KR/HOWTO.
Signed-off-by: Lee, Jae-Hong <pyrasis@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes some minor typos in Documentation/ko_KR/stable_api_nonsense.txt
Signed-off-by: Lee, Jae-Hong <pyrasis@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes some minor typos in Documentation/ko_KR/HOWTO.
Signed-off-by: Lee, Jae-Hong <pyrasis@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct use of devnum in supports_autosuspend documentation, the sysfs path
contains busnum-port.port.port not busnum-devnum (which is the usb bus device
address).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The config descriptors as read from /proc/bus/usb/BBB/DDD are in *bus* endian
format. Correct proc_usb_info.txt to correctly reflect that.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor so that register writes for configuration are only performed if
the device has a regmap provided and also register as a platform driver.
This allows the driver to be used to manage GPIO based control of the
device.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The binding document says that all properties are required but in fact
almost all are optional (and should be) - update the document to reflect
this.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no software visible differences that I am aware of but in case
any are discovered allow the DTS to specify exactly which device is
present.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no good reason to run complete() in hard interrupt
disabled context.
After switch to run complete() in tasklet, we will enable local IRQs
when calling complete() since we can do it at that time.
Even though we still disable IRQs now when calling complete()
in tasklet, the URB documentation is updated to claim complete()
will be run in tasklet context and local IRQs will be enabled, so
that USB drivers can know the change and avoid one deadlock caused
by: assume IRQs disabled in complete() and call spin_lock() to
hold lock which might be acquired in interrupt context.
Current spin_lock() usages in drivers' complete() will be cleaned
up at the same time, and once the cleanup is finished, local IRQs
will be enabled when calling complete() in tasklet.
Also fix description about type of usb_complete_t, and remove the
advice of running completion handler in tasklet for decreasing
system latency.
Cc: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the new device tree parameters for Tegra30 USB PHY.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Exynos PCIe IP consists of Synopsys specific part and Exynos
specific part. Only core block is a Synopsys Designware part;
other parts are Exynos specific.
Also, the Synopsys Designware part can be shared with other
platforms; thus, it can be split two parts such as Synopsys
Designware part and Exynos specific part.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
The binding spec wasn't clear that the order of the phandles in the
usb-phy array has meaning. Clarify this point in the binding that
it should be <USB2-HS-PHY, USB3-SS-PHY>.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
an uncorrected error is reported. Ignore it when checking
error signatures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LbVP
-----END PGP SIGNATURE-----
Merge tag 'please-pull-mce-f-bit' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Pull MCE-uncorrected-error fix from Tony Luck:
"Bit 12 may or may not be set in MCi_STATUS.MCACOD when
an uncorrected error is reported. Ignore it when checking
error signatures."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A lot of drivers check the frame protocol for ETH_P_PAE,
for various reasons (like making those more reliable).
Add a new flags bitmap to the TX control info and a new
flag indicating the control port protocol is in use to
let all drivers also apply such logic to other control
port protocols, should they be configured.
Also use the new flag in the iwlwifi drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for ads1115 device to ads1015 driver.
Based on work of Emiliano Carnati <carnatiatebneuro.com>.
Tested on ARM CPU based board.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".
Since there is no public documentation, this driver is mostly the
one published by MOXA that has been heavily cleaned up / ported
from linux 2.6.9.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull i2c fixes from Wolfram Sang:
"Some driver bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mv64xxx: Document the newly introduced allwinner compatible
i2c: Fix Kontron PLD prescaler calculation
i2c: i2c-mxs: Use DMA mode even for small transfers
We don't need to set .owner = THIS_MODULE any more in cpufreq drivers
as this field isn't used any more by the cpufreq core.
This patch removes it and updates all dependent drivers accordingly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull media fixes from Mauro Carvalho Chehab:
"Some driver fixes (em28xx, coda, usbtv, s5p, hdpvr and ml86v7667) and
a fix for media DocBook"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: fix dependency
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
Add support for restart and poweroff functionality present on MSM chipsets
with the MPM2 ps-hold hardware.
Signed-off-by: Abhimanyu Kapur <abhimany@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Get rid of the last module parameter for SCTP and make this
configurable via sysctl for SCTP like all the rest of SCTP's
configuration knobs.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a complete rewrite of the Xen TPM frontend driver, taking
advantage of a simplified frontend/backend interface and adding support
for cancellation and timeouts. The backend for this driver is provided
by a vTPM stub domain using the interface in Xen 4.3.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Acked-by: Matthew Fioravante <matthew.fioravante@jhuapl.edu>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
A couple of fixes to bring the DT binding documentation for Palmas into
sync with the code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=faDW
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator DT binding fixes from Mark Brown:
"A couple of fixes to bring the DT binding documentation for Palmas
into sync with the code"
* tag 'regulator-v3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: palmas-pmic: doc: remove ti,tstep
regulator: palmas-pmic: doc: fix typo for sleep-mode
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section. Fix
the example code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The pin list is the same for any board using the CODEC.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Add compatible "fsl,mpic-msi-v4.3" for MPIC v4.3. MPIC v4.3 contains
MSIIR and MSIIR1. MSIIR supports 8 MSI registers and MSIIR1 supports
16 MSI registers, but uses different IBS and SRS shift. When using
MSIR1, the interrupt number is not consecutive. It is hard to use
'msi-available-ranges' to describe the ranges of the available
interrupt, so MPIC v4.3 does not support this property.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
[scottwood@freescale.com: minor grammar fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
pinctrl bindings can benefit from generic property names that define
which pins a "pin configuration node" affects, and which mux function
to select onto those pins. Document new properties for this purpose so
that other bindings may refer to them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reword the section of pinctrl-bindings.txt that describes generic
properties that pinctrl bindings may use. The aim is to make the text
clearer, and more explicitly call out the responsibility of individual
bindings that use the generic properties to define which of the
properties are used, and how.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SCC (Serial Configuration Controller) is used to set initial
conditions for the test chip (TC2). Its registers are also mapped
in normal address space and used to obtain runtime information
and for power management.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Neat that QA (and Ben) keeps on humming along while I'm on vacation, so
you already get the next feature pull request:
- proper eLLC support for HSW from Ben
- more interrupt refactoring
- add w/a tags where we implement them already (Damien)
- hangcheck fixes (Chris) + hangcheck stats (Mika)
- flesh out the new vm structs for ppgtt and ggtt (Ben)
- PSR for Haswell, still disabled by default (Rodrigo et al.)
- pc8+ refclock sequence code from Paulo
- more interrupt refactoring from Paulo, unifying ilk/snb with the ivb/hsw
interrupt code
- full solution for the Haswell concurrent reg access issues (Chris)
- fix racy object accounting, used by some new leak tests
- fix sync polarity settings on ch7xxx dvo encoder
- random bits&pieces, little fixes and better debug output all over
[airlied: fix conflict with drm_mm cleanups]
* tag 'drm-intel-next-2013-07-26-fixed' of git://people.freedesktop.org/~danvet/drm-intel: (289 commits)
drm/i915: Do not dereference NULL crtc or fb until after checking
drm/i915: fix pnv display core clock readout out
drm/i915: Replace open-coded offset_in_page()
drm/i915: Retry DP aux_ch communications with a different clock after failure
drm/i915: Add messages useful for HPD storm detection debugging (v2)
drm/i915: dvo_ch7xxx: fix vsync polarity setting
drm/i915: fix the racy object accounting
drm/i915: Convert the register access tracepoint to be conditional
drm/i915: Squash gen lookup through multiple indirections inside GT access
drm/i915: Use the common register access functions for NOTRACE variants
drm/i915: Use a private interface for register access within GT
drm/i915: Colocate all GT access routines in the same file
drm/i915: fix reference counting in i915_gem_create
drm/i915: Use Graphics Base of Stolen Memory on all gen3+
drm/i915: disable stolen mem for OVERLAY_NEEDS_PHYSICAL
drm/i915: add functions to disable and restore LCPLL
drm/i915: disable CLKOUT_DP when it's not needed
drm/i915: extend lpt_enable_clkout_dp
drm/i915: fix up error cleanup in i915_gem_object_bind_to_gtt
drm/i915: Add some debug breadcrumbs to connector detection
...
This patch adds the device tree bindings for the bcm281xx reboot code.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Acked-by: Christian Daudt <csd@broadcom.com>
Change compatible string to something more standard.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As atmel-ssc can be used with DMA, the documentation should be updated.
Also, a configuration DMA example is given.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Description of the Asoc machine driver for an at91sam9x5 based board
with a wm8731 audio DAC. Wm8731 is clocked by a crystal and used as a
master on the SSC/I2S interface. Its connections are a headphone jack
and an Line input jack.
[Richard: this is based on an old patch from Nicolas that I forward
ported and reworked to use only device tree]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There may be some platforms using fsl-ssi that do not have a DMA driver
with generic DMA bindings. So this patch adds support for the generic
DMA bindings, while still accepting the old "fsl,dma-events" property if
"dmas" is not found.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for non-dma pcm for imx platforms with imx-pcm-fiq support.
Instead of imx-pcm-audio, in this case imx-pcm-fiq-audio device is added
and the SIER flags are set differently.
We need imx-pcm-fiq for some boards that use an incompatible codec.
imx-pcm-fiq handles those codecs differently and allows to operate with
them. DMA is not possible because some data sent by the codecs, e.g.
wm9712, is not in the datastream. Also some data is mixed up in the
fifos, so that we need to sort them out manually.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Adds a function to parse a default port configuration from devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The new device tree layout encodes the window's target ID and attribute
in the PCIe controller node's ranges property. This allows to parse
such entries to obtain such information and use the recently introduced
MBus API to create the windows, instead of using the current name based
scheme.
Cc: devicetree@vger.kernel.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Introduce the devicetree binding for the mvebu MBus driver
avaiable in the mvebu SoCs (Armada 370/XP, Kirkwood, Dove, ...).
This binding provides an accurate model of the SoC address space,
and allows to declare the address and size of the decoding windows the MBus
needs to access the peripherals, together with the target ID and attribute
for those windows.
The binding is composed of two required nodes: one for the MBus bus
and one for the MBus controller.
Cc: devicetree@vger.kernel.org
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add sysfs entry gc_idle to control the gc policy. Where
gc_idle = 1 corresponds to selecting a cost benefit approach,
while gc_idle = 2 corresponds to selecting a greedy approach
to garbage collection. The selection is mutually exclusive one
approach will work at any point. If gc_idle = 0, then this
option is disabled.
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
[Jaegeuk Kim: change the select_gc_type() flow slightly]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add sysfs entries to control the timing parameters for
f2fs gc thread.
Various Sysfs options introduced are:
gc_min_sleep_time: Min Sleep time for GC in ms
gc_max_sleep_time: Max Sleep time for GC in ms
gc_no_gc_sleep_time: Default Sleep time for GC in ms
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
[Jaegeuk Kim: fix an umount bug and some minor changes]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In case that the nand device will support some features like Nand Flash
Controller, we want to make the sub feature as a sub node of nand device.
Use such organization it is easy to enable/disable feature, also it is back
compatible and more readable.
If the sub-node has a compatible property then it is a driver not partition.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[ added a missing newline -Brian ]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch enable writing nand flash via NFC SRAM. It will minimize the CPU
overhead. The SRAM write only support ECC_NONE and ECC_HW with PMECC.
To enable this NFC write by SRAM feature, you can add a string in dts under
NFC driver node.
This driver has been tested on SAMA5D3X-EK with JFFS2, YAFFS2, UBIFS and
mtd-utils.
Here is part of mtd_speedtest (writing test) result, compare with non-NFC
writing, it reduces %65 cpu load with loss %12 speed.
- commands use to test:
# insmod /mnt/mtd_speedtest.ko dev=2 &
# top -n 30 -d 1 | grep speedtest
- test result:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: MTD device size 41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64
mtd_speedtest: testing eraseblock write speed
509 495 root D 1164 0% 7% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 8% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root R 1164 0% 5% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: eraseblock write speed is 5194 KiB/s
mtd_speedtest: testing page write speed
509 495 root D 1164 0% 32% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 27% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 25% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 30% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: page write speed is 5024 KiB/s
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch will set the nand dma support in dts. Since we will not use
cpu_is_xxx() in nand driver. We needn't include the mach/cpu.h any more.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add nand bank selection and timings to the device tree bindings.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
[Added some documentation]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds new, Common Clock Framework-based clock driver for Samsung
S3C64xx SoCs. The driver is just added, without actually letting the
platforms use it yet, since this requires more intermediate steps.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add PCM1792A spi mode codec support. This version implements only
a subset of functionalities. Tested connect to a pandaboard ES
device and based on recently pcm1681 codec.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The virtual console has (undocumented) module parameters to set the
colors for italic and underlined text, but the default text color was
hardcoded for some reason. This made it impossible to change the color
for startup messages, or to set the default for new virtual consoles.
Add a module parameter for that, and document the entire bunch.
Any hacker who thinks that a command prompt on a "black screen with
white font" is not supicious enough can now use the kernel parameter
vt.color=10 to get a nice, evil green.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original DMA support works only when RTS/CTS is enabled.
(see the "e800163 serial: mxs-auart: add the DMA support for mx28")
But after several patches, DMA support has lost this limit.
(see the "bcc20f9 serial: mxs-auart: move to use generic DMA helper")
So an UART without the RTS/CTS lines may also enables the DMA support,
in which case the UART may gets unpredictable results.
This patch adds an optional property for the UART DT node
which indicates the UART has RTS and CTS lines, and it also means you
enable the DMA support for this UART.
This patch also adds a macro MXS_AUART_RTSCTS, and uses it to check
RTS/CTS before we enable the DMA for the UART.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on system design, platform needs to detect the VBUS or ID or
both. Provide option to select this through platform data to
disable part of cable detection through palmas-usb.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Extcon for palma driver does not need vbus supply and hence
removing this from devicetree document/bindings.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
The driver name is extcon/extcon-palmas.c and hence renaming the
device tree binding document to extcon-palmas.txt.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Modified dwc3-omap to receive connect and disconnect notification using
extcon framework. Also did the necessary cleanups required after
adapting to extcon framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Pull networking fixes from David Miller:
1) Don't ignore user initiated wireless regulatory settings on cards
with custom regulatory domains, from Arik Nemtsov.
2) Fix length check of bluetooth information responses, from Jaganath
Kanakkassery.
3) Fix misuse of PTR_ERR in btusb, from Adam Lee.
4) Handle rfkill properly while iwlwifi devices are offline, from
Emmanuel Grumbach.
5) Fix r815x devices DMA'ing to stack buffers, from Hayes Wang.
6) Kernel info leak in ATM packet scheduler, from Dan Carpenter.
7) 8139cp doesn't check for DMA mapping errors, from Neil Horman.
8) Fix bridge multicast code to not snoop when no querier exists,
otherwise mutlicast traffic is lost. From Linus Lüssing.
9) Avoid soft lockups in fib6_run_gc(), from Michal Kubecek.
10) Fix races in automatic address asignment on ipv6, which can result
in incorrect lifetime assignments. From Jiri Benc.
11) Cure build bustage when CONFIG_NET_LL_RX_POLL is not set and rename
it CONFIG_NET_RX_BUSY_POLL to eliminate the last reference to the
original naming of this feature. From Cong Wang.
12) Fix crash in TIPC when server socket creation fails, from Ying Xue.
13) macvlan_changelink() silently succeeds when it shouldn't, from
Michael S Tsirkin.
14) HTB packet scheduler can crash due to sign extension, fix from
Stephen Hemminger.
15) With the cable unplugged, r8169 prints out a message every 10
seconds, make it netif_dbg() instead of netif_warn(). From Peter
Wu.
16) Fix memory leak in rtm_to_ifaddr(), from Daniel Borkmann.
17) sis900 gets spurious TX queue timeouts due to mismanagement of link
carrier state, from Denis Kirjanov.
18) Validate somaxconn sysctl to make sure it fits inside of a u16.
From Roman Gushchin.
19) Fix MAC address filtering on qlcnic, from Shahed Shaikh.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits)
qlcnic: Fix for flash update failure on 83xx adapter
qlcnic: Fix link speed and duplex display for 83xx adapter
qlcnic: Fix link speed display for 82xx adapter
qlcnic: Fix external loopback test.
qlcnic: Removed adapter series name from warning messages.
qlcnic: Free up memory in error path.
qlcnic: Fix ingress MAC learning
qlcnic: Fix MAC address filter issue on 82xx adapter
net: ethernet: davinci_emac: drop IRQF_DISABLED
netlabel: use domain based selectors when address based selectors are not available
net: check net.core.somaxconn sysctl values
sis900: Fix the tx queue timeout issue
net: rtm_to_ifaddr: free ifa if ifa_cacheinfo processing fails
r8169: remove "PHY reset until link up" log spam
net: ethernet: cpsw: drop IRQF_DISABLED
htb: fix sign extension bug
macvlan: handle set_promiscuity failures
macvlan: better mode validation
tipc: fix oops when creating server socket fails
net: rename CONFIG_NET_LL_RX_POLL to CONFIG_NET_RX_BUSY_POLL
...
Add devm_iio_device_alloc() and devm_iio_device_free() functions
to list of supported calls.
Signed-off-by: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds IIO driver for APDS9300 ambient light sensor (ALS).
http://www.avagotech.com/docs/AV02-1077EN
The driver allows to read raw data from ADC registers or calculate
lux value. It also can handle threshold interrupt.
Signed-off-by: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This commit adds a device tree vendor prefix for Avago Technologies.
Signed-off-by: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Nuvoton NAU7802 ADC is a 24-bit 2-channels I2C ADC, with adjustable
gain and sampling rates.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds devicetree bindings for max8660, along with some
documentation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit 85c9969074.
Alexander wishes to remove this patch as it is incorrect.
Reported-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCM1681 can be controlled via I2C, SPI or in bootstrap mode (no control mode). This code add
support only for I2C mode.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add DT support to the SCCNCP serial driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A collection of expectations and operational details about how
networking development takes place in the context of the netdev
mailing list.
The content is meant to capture specific items that are unique
to netdev workflow, and not re-document generic linux expectations
that are already captured elsewhere.
This was originally proposed[1] as a regular posting mailing list
FAQ, but it probably is more universally accessible here in tree.
[1] https://lwn.net/Articles/559211/
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a binding for the arm architected timer hardware's memory
mapped interface. The mmio timer hardware is made up of one base
frame and a collection of up to 8 timer frames, where each of the
8 timer frames can have either one or two views. A frame
typically maps to a privilege level (user/kernel, hypervisor,
secure). The first view has full access to the registers within a
frame, while the second view can be restricted to particular
registers within a frame. Each frame must support a physical
timer. It's optional for a frame to support a virtual timer.
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robherring2@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
1. describe compatible variable "Must be" instead of "Should be".
2. change description so it's from the point of view of the device
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Fix device tree bindings document with the correct clock name.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Make it easier to break up printk into bite-sized chunks.
Remove printk path/filename from comment.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's always been a hassle that if an external journal's
device number changes, the filesystem won't mount.
And since boot-time enumeration can change, device number
changes aren't unusual.
The current mechanism to update the journal location is by
passing in a mount option w/ a new devnum, but that's a hassle;
it's a manual approach, fixing things after the fact.
Adding a mount option, "-o journal_path=/dev/$DEVICE" would
help, since then we can do i.e.
# mount -o journal_path=/dev/disk/by-label/$JOURNAL_LABEL ...
and it'll mount even if the devnum has changed, as shown here:
# losetup /dev/loop0 journalfile
# mke2fs -L mylabel-journal -O journal_dev /dev/loop0
# mkfs.ext3 -L mylabel -J device=/dev/loop0 /dev/sdb1
Change the journal device number:
# losetup -d /dev/loop0
# losetup /dev/loop1 journalfile
And today it will fail:
# mount /dev/sdb1 /mnt/test
mount: wrong fs type, bad option, bad superblock on /dev/sdb1,
missing codepage or helper program, or other error
In some cases useful info is found in syslog - try
dmesg | tail or so
# dmesg | tail -n 1
[17343.240702] EXT3-fs (sdb1): error: couldn't read superblock of external journal
But with this new mount option, we can specify the new path:
# mount -o journal_path=/dev/loop1 /dev/sdb1 /mnt/test
#
(which does update the encoded device number, incidentally):
# umount /dev/sdb1
# dumpe2fs -h /dev/sdb1 | grep "Journal device"
dumpe2fs 1.41.12 (17-May-2010)
Journal device: 0x0701
But best of all we can just always mount by journal-path, and
it'll always work:
# mount -o journal_path=/dev/disk/by-label/mylabel-journal /dev/sdb1 /mnt/test
#
So the journal_path option can be specified in fstab, and as long as
the disk is available somewhere, and findable by label (or by UUID),
we can mount.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The module was "permanent", due to the special tproxy skb->destructor.
Nowadays we have tcp early demux and its sock_edemux destructor in
networking core which can be used instead.
Thanks to early demux changes the input path now also handles
"skb->sk is tw socket" correctly, so this no longer needs the special
handling introduced with commit d503b30bd6
(netfilter: tproxy: do not assign timewait sockets to skb->sk).
Thus:
- move assign_sock function to where its needed
- don't prevent timewait sockets from being assigned to the skb
- remove nf_tproxy_core.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add device tree based support for HID over I2C devices.
Tested on an Odroid-X board with a Synaptics touchpad.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID core provides the same functionality and can convert the input event
to a raw output report. We can thus drop UHID_OUTPUT_EV and rely on the
mandatory UHID_OUTPUT.
User-space wasn't able to do anything with UHID_OUTPUT_EV, anyway. They
don't have access to the report fields.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Exynos5250 G2D IP requires only the gate clock. Update the
binding documentation accordingly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Added clock entries for thermal management unit (TMU) for
Exynos4 SoCs.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds DT compatible string for s2mps11 and binding documentation.
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add TPS659038 Device Tree documentation.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| If you want to test which effects syncookies have to your
| network connections you can set this knob to 2 to enable
| unconditionally generation of syncookies.
Original idea and first implementation by Eric Dumazet.
Cc: Florian Westphal <fw@strlen.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
hdmi driver needs hdmiphy clock which is one of the parent
for hdmi mux clock. This is required while changing the parent
of mux clock.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
hdmi driver needs to change the parent of hdmi clock
frequently between pixel clock and hdmiphy clock. hdmiphy is
not stable after power on and for a short interval while changing
the phy configuration. For this duration pixel clock is used to
clock hdmi.
This patch is exposing the mux for changing parent.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
commit 79d743c177 ("clk: exynos5250: Add enum entries for divider
clock of i2s1 and i2s2") added two new clock entries. Add the clock
entry enum numbers to documentation.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
All lirc drivers that can transmit, return EINVAL when they are passed
more than IR data than they can send. That is, except for two drivers
which I touched.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the erroneous V4L2_CID_JPEG_IMAGE_QUALITY control name
with V4L2_CID_JPEG_COMPRESSION_QUALITY.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
dbf2576e37 ("workqueue: make all workqueues non-reentrant") made
WQ_NON_REENTRANT no-op but the following patches didn't remove the
flag or update the documentation. Let's mark the flag deprecated and
update the documentation accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
The device tree binding documentation for tegra20-usb-phy used to claim
that the vbus-supply property is required for host phys and optional
for otg phys. This should be the other way around.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds gate clock for G2D IP for Exynos5250 SoC.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds some description on fsck.f2fs and dump.f2fs which is
recently merged into f2fs-tools.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
VAIO-Z laptops need to use the specific DAC for the speaker output
by some unknown reason although the codec itself supports the flexible
connection. So we implemented a workaround by a new flag,
no_primary_hp, for assigning the speaker pin first.
This worked until 3.8 kernel, but it got broken because the driver
learned for a better multi-io pin mapping, and not it can assign two
mic pins for multi-io. Since the multi-io requires to be the primary
output, the hp and two mic pins are assigned in prior to the speaker
in the end.
Although the machine has two mic pins, one of them is used as a noise-
canceling headphone, thus it's no real retaskable mic jack. Thus, at
best, we can disable the multi-io assignment and make the parser
behavior back to the state before the multi-io.
This patch adds again a new flag, no_multi_io, to indicate that the
device has no multi-io capability, and set it in the fixup for
VAIO-Z. The no_multi_io flag itself can be used generically, added
via a helper line, too.
Reported-by: Tormen <my.nl.abos@gmail.com>
Reported-by: Adam Williamson <awilliam@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current fixup for dell-bios model with STAC9228 codec contains the
override of pin 0x0c for analog mic. But this is actually just adding
a bogus pin and confuses the parser. Better to remove it for the
auto-mic switching.
Meanwhile, for a possible regression, keep the old configuration as
model=dell-bios-amic, so that people can test it again quickly.
Tested on Dell 1420n laptop.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Document vbus-supply as an optional property for host mode phy-tegra-usb PHYs.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds OF match table to the driver to allow instantiating it
using device tree.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
all other drivers using Synopsys IPs with DT
have a compatible of snps,$driver, in order
to add consistency, we are switching over to
snps,dwc3 but keeping synopsys,dwc3 in the core
driver to maintain backwards compatibility.
New DTS bindings should NOT use synopsys,dwc3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this helper will be used for controllers which
want to work at a lower speed even though they
support higher USB transfer rates.
One such case is Texas Instruments' AM437x
SoC where it uses a USB3 controller without
a USB3 PHY, rendering the controller USB2-only.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP is common
across all the ST parts for settop box platforms.
ASC is embedded in ST COMMS IP block. It supports Rx & Tx functionality.
It support all industry standard baud rates.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJR8cSDAAoJEIwa5zzehBx3dgsQAIRYV0xKDWYUgzvLGx1Gn/eC
tUw5JeT13eSyEzPL8vAHyMFkI/N7yUzExMjzULPsDXiKHCkRDosLqwxNRFCSVBEv
vp6ipoa75t+l7sys4lOoTVZGY+Pt0SJDIs1jpkTzWPt+BtFanKpaOFJN0hCMZh1j
x0ls+TX4UUsl7MhxtTSEHSMIjt+8bz4rxE6shQOSRePGHkQKrsS1VrFAIC+u1x5b
bkAU3KdLCu5i4qNSU5Niqg2VgRWzxrkR1lQiY8e0BtGqmret9itYFsRWwdZ0qrLQ
Q6aYnR6O/uWH1i2g+Fcl+R4FJo96hy7KqbI0wJmgKlpG5nRQWhCXyYWo86xjw97G
JOA4EHyV+wcmQIo7ZwjYRae7fJYQeRBdUT6/rVnlW++Hi7ZeHI2DLyNLkwG7iXat
iD3OPgzsQ2beK5QTB6fL8iTv+q4o4hXHFDmFukjPYdR3NPHNaJ+uuaI78rUAblmc
RoQ38UzSL82kiseaFP8b7sU9P1JF2hopPDLA7rdSyKBCLczEhzXvgXG1XJVwOdmA
FTBf1g9taawLAxzaJOC82wYrTCLWX2dzv3DeCbaEpzYq1nblJrqYLerQ6Rb0c5xy
V7a+h4aQhLsZvA2Qu7NGBD0wv47d7r5UAPUS1i4Em1Yi+syrBNY4XCiJhBH0fZc5
k4PXz5wVMhpyVLrX6bVd
=XOG3
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge
window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
mfd: max8925: fix dt code for backlight
ARM: omap5: Only select errata 798181 if SMP
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: multi_v7_defconfig: Select USB chipidea driver
ARM: pxa: propagate errors from regulator_enable() to pxamci
ARM: zynq: fix compilation warning
ARM: keystone: fix compilation warning
ARM: highbank: Only touch common coherency control register fields
ARM: footbridge: fix overlapping PCI mappings
dmaengine: shdma: fix a build failure on platforms with no DMA support
ARM: STi: Set correct ARM ERRATAs.
ARM: dts: STi: Fix pinconf setup for STiH416 serial2
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
ARM: davinci: defconfig: enable EDMA driver
...
Here are some char/misc patches for 3.11-rc3. It's pretty much just:
- mei fixes
- hyperv fixes
- new ja_JP translation update
all tiny stuff, but fixes for issues people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHyqBcACgkQMUfUDdst+ylMswCgoppo0tfChc0KfyAcsgWwJr2o
iTsAoLEJ2sg8GIGYI765UMXWAkzJyCxR
=oHJj
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here are some char/misc patches for 3.11-rc3. It's pretty much just:
- mei fixes
- hyperv fixes
- new ja_JP translation update
all tiny stuff, but fixes for issues people have reported."
* tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
HOWTO ja_JP sync
mei: me: fix waiting for hw ready
mei: don't have to clean the state on power up
mei: me: fix reset state machine
mei: hbm: fix typo in error message
Tools: hv: KVP: Fix a bug in IPV6 subnet enumeration
Drivers: hv: balloon: Do not post pressure status if interrupted
Drivers: hv: balloon: Fix a bug in the hot-add code
Drivers: hv: vmbus: incorrect device name is printed when child device is unregistered
add OF support for the adv7343 driver.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
add OF support for the ths8200 driver.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Due to the variable availability of the clock API there is no code in the
driver to use these at present, for the time being the machine drivers
will need to handle requesting clocks.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Fixes the last three errors of media_api DocBook validatation:
(...)
media_api.xml:414: element imagedata: validity error : Value "SVG" for attribute format of imagedata is not among the enumerated set
media_api.xml:432: element imagedata: validity error : Value "SVG" for attribute format of imagedata is not among the enumerated set
media_api.xml:452: element imagedata: validity error : Value "SVG" for attribute format of imagedata is not among the enumerated set
(...)
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A framebuffer of this format is set up by SHIELD's bootloader.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clocks should be numbered sequentially as they are represented as
enum values in the clock driver.
Typo introduced by commit 17d4caccef ("clk: exynos5250: register
display block gate clocks to common clock framework")
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
If we want to map GPU memory into user-space, we need to linearize the
addresses to not confuse mm-core. Currently, GEM and TTM both implement
their own offset-managers to assign a pgoff to each object for user-space
CPU access. GEM uses a hash-table, TTM uses an rbtree.
This patch provides a unified implementation that can be used to replace
both. TTM allows partial mmaps with a given offset, so we cannot use
hashtables as the start address may not be known at mmap time. Hence, we
use the rbtree-implementation of TTM.
We could easily update drm_mm to use an rbtree instead of a linked list
for it's object list and thus drop the rbtree from the vma-manager.
However, this would slow down drm_mm object allocation for all other
use-cases (rbtree insertion) and add another 4-8 bytes to each mm node.
Hence, use the separate tree but allow for later migration.
This is a rewrite of the 2012-proposal by David Airlie <airlied@linux.ie>
v2:
- fix Docbook integration
- drop drm_mm_node_linked() and use drm_mm_node_allocated()
- remove unjustified likely/unlikely usage (but keep for rbtree paths)
- remove BUG_ON() as drm_mm already does that
- clarify page-based vs. byte-based addresses
- use drm_vma_node_reset() for initialization, too
v4:
- allow external locking via drm_vma_offset_un/lock_lookup()
- add locked lookup helper drm_vma_offset_lookup_locked()
v5:
- fix drm_vma_offset_lookup() to correctly validate range-mismatches
(fix (offset > start + pages))
- fix drm_vma_offset_exact_lookup() to actually do what it says
- remove redundant vm_pages member (add drm_vma_node_size() helper)
- remove unneeded goto
- fix documentation
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Both old URLs are broken, so update them.
Signed-off-by: Martin Nordholts <enselic@gmail.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add pfuze100 regulator driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Attached is Documentation/ja_JP/HOWTO sync patch for 3.10.
This patch was reviewed by Japanese translation community called JF.
Signed-off-by: Tsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Idea of this patch is to add optional limitation of number of
unsent bytes in TCP sockets, to reduce usage of kernel memory.
TCP receiver might announce a big window, and TCP sender autotuning
might allow a large amount of bytes in write queue, but this has little
performance impact if a large part of this buffering is wasted :
Write queue needs to be large only to deal with large BDP, not
necessarily to cope with scheduling delays (incoming ACKS make room
for the application to queue more bytes)
For most workloads, using a value of 128 KB or less is OK to give
applications enough time to react to POLLOUT events in time
(or being awaken in a blocking sendmsg())
This patch adds two ways to set the limit :
1) Per socket option TCP_NOTSENT_LOWAT
2) A sysctl (/proc/sys/net/ipv4/tcp_notsent_lowat) for sockets
not using TCP_NOTSENT_LOWAT socket option (or setting a zero value)
Default value being UINT_MAX (0xFFFFFFFF), meaning this has no effect.
This changes poll()/select()/epoll() to report POLLOUT
only if number of unsent bytes is below tp->nosent_lowat
Note this might increase number of sendmsg()/sendfile() calls
when using non blocking sockets,
and increase number of context switches for blocking sockets.
Note this is not related to SO_SNDLOWAT (as SO_SNDLOWAT is
defined as :
Specify the minimum number of bytes in the buffer until
the socket layer will pass the data to the protocol)
Tested:
netperf sessions, and watching /proc/net/protocols "memory" column for TCP
With 200 concurrent netperf -t TCP_STREAM sessions, amount of kernel memory
used by TCP buffers shrinks by ~55 % (20567 pages instead of 45458)
lpq83:~# echo -1 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# (super_netperf 200 -t TCP_STREAM -H remote -l 90 &); sleep 60 ; grep TCP /proc/net/protocols
TCPv6 1880 2 45458 no 208 yes ipv6 y y y y y y y y y y y y y n y y y y y
TCP 1696 508 45458 no 208 yes kernel y y y y y y y y y y y y y n y y y y y
lpq83:~# echo 131072 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# (super_netperf 200 -t TCP_STREAM -H remote -l 90 &); sleep 60 ; grep TCP /proc/net/protocols
TCPv6 1880 2 20567 no 208 yes ipv6 y y y y y y y y y y y y y n y y y y y
TCP 1696 508 20567 no 208 yes kernel y y y y y y y y y y y y y n y y y y y
Using 128KB has no bad effect on the throughput or cpu usage
of a single flow, although there is an increase of context switches.
A bonus is that we hold socket lock for a shorter amount
of time and should improve latencies of ACK processing.
lpq83:~# echo -1 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# perf stat -e context-switches ./netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3
OMNI Send TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.7.84 () port 0 AF_INET : +/-2.500% @ 99% conf.
Local Remote Local Elapsed Throughput Throughput Local Local Remote Remote Local Remote Service
Send Socket Recv Socket Send Time Units CPU CPU CPU CPU Service Service Demand
Size Size Size (sec) Util Util Util Util Demand Demand Units
Final Final % Method % Method
1651584 6291456 16384 20.00 17447.90 10^6bits/s 3.13 S -1.00 U 0.353 -1.000 usec/KB
Performance counter stats for './netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3':
412,514 context-switches
200.034645535 seconds time elapsed
lpq83:~# echo 131072 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# perf stat -e context-switches ./netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3
OMNI Send TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.7.84 () port 0 AF_INET : +/-2.500% @ 99% conf.
Local Remote Local Elapsed Throughput Throughput Local Local Remote Remote Local Remote Service
Send Socket Recv Socket Send Time Units CPU CPU CPU CPU Service Service Demand
Size Size Size (sec) Util Util Util Util Demand Demand Units
Final Final % Method % Method
1593240 6291456 16384 20.00 17321.16 10^6bits/s 3.35 S -1.00 U 0.381 -1.000 usec/KB
Performance counter stats for './netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3':
2,675,818 context-switches
200.029651391 seconds time elapsed
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-By: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP mailing list address to send patches or questions
to is linux-sctp@vger.kernel.org and not
lksctp-developers@lists.sourceforge.net anymore. Therefore,
update all occurences.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This branch contains a couple of minor bug fixes and documentation
additions, but the bulk of it are several changes to the MAINTAINERS
file regarding the subsystems I've been involved with.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PuWV
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree bug fixes and maintainership updates from Grant Likely:
"This branch contains a couple of minor bug fixes and documentation
additions, but the bulk of it are several changes to the MAINTAINERS
file regarding the subsystems I've been involved with"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/irq: init struct resource to 0 in of_irq_to_resource()
of/irq: Avoid calling list_first_entry() for empty list
of: add vendor prefixes for hisilicon
of: add vendor prefix for Qualcomm Atheros, Inc.
MAINTAINERS: Fix incorrect status tag
MAINTAINERS: Refactor device tree maintainership
MAINTAINERS: Change device tree mailing list
MAINTAINERS: Remove Grant Likely
* A few device tree source fixes regarding pinctrl, clock, and pwm
backlight.
* Fixes imx28 and imx51 audio driver failure caused by sgtl5000 codec
driver change by supplying the correct clock for codec.
* imx6q emi_sel clock muxing and imx6q-iomuxc-gpr macro fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJR5B55AAoJEFBXWFqHsHzOEGoH/2DesLDZkQbUCn+w7Z3H7HYi
QAPeG1F/Ke3cBSaT+v/Z+46MgmU2gyQkxk08GRtPuVAZwCuWxSUN1H6+yakeBdHb
XGXR25RbbASIpYdYnC37eKiU2itiBmD7CRbWJ5xPHEluAgr47vr3OKfls6laii3b
nSM4sKz45PxBJ55M0qcE+A6oVdf9c+G0vm0aX14xEiLEUghB/U0KNKWp+B63hwfh
tg11gNwr2dO8jv51xpwJXH17juoZ46srOzmxERJm3j08JSz/tJSvIQajSsg54aLT
pAxToPAeuGGga5+7AanGT+repzZdd74Lp3U/lGw6WpaxLOpFf5Am3841O8qqCLw=
=q0LM
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo, imx fixes for 3.11:
- A few device tree source fixes regarding pinctrl, clock, and pwm
backlight.
- Fixes imx28 and imx51 audio driver failure caused by sgtl5000 codec
driver change by supplying the correct clock for codec.
- imx6q emi_sel clock muxing and imx6q-iomuxc-gpr macro fixes
* tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: Pass a real clock to the codec
ARM i.MX53: mba53: Fix PWM backlight DT node
ARM: imx: fix vf610 enet module clock selection
ARM: mxs: saif0 is the clock provider to sgtl5000
ARM: i.MX6Q: correct emi_sel clock muxing
ARM i.MX6Q: Fix IOMUXC GPR1 defines for ENET_CLK_SEL and IPU1/2_MUX
ARM: i.MX27: Typo fix
ARM: imx27: Fix documentation for SPLL clock
ARM i.MX53: Fix UART pad configuration
This patch changes the "acpi_osi=" boot parameter implementation so
that:
1. "acpi_osi=!" can be used to disable all _OSI OS vendor strings by
default. It is meaningless to specify "acpi_osi=!" multiple
times as it can only affect the default state of the target _OSI
strings.
2. "acpi_osi=!*" can be used to remove all _OSI OS vendor strings
and all _OSI feature group strings. It is useful to specify
"acpi_osi=!*" multiple times through kernel command line to
override the current state of the target _OSI strings.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch introduces "acpi_osi=!" command line to force Linux replying
"UNSUPPORTED" to all of the _OSI strings. This patch is based on an
ACPICA enhancement - the new API acpi_update_interfaces().
The _OSI object provides the platform with the ability to query OSPM
to determine the set of ACPI related interfaces, behaviors, or
features that the operating system supports. The argument passed to
the _OSI is a string like the followings:
1. Feature Group String, examples include
Module Device
Processor Device
3.0 _SCP Extensions
Processor Aggregator Device
...
2. OS Vendor String, examples include
Linux
FreeBSD
Windows
...
There are AML codes provided in the ACPI namespace written in the
following style to determine OSPM interfaces / features:
Method(OSCK)
{
if (CondRefOf(_OSI, Local0))
{
if (\_OSI("Windows"))
{
Return (One)
}
if (\_OSI("Windows 2006"))
{
Return (Ones)
}
Return (Zero)
}
Return (Zero)
}
There is a debugging facility implemented in Linux. Users can pass
"acpi_osi=" boot parameters to the kernel to tune the _OSI evaluation
result so that certain AML codes can be executed. Current
implementation includes:
1. 'acpi_osi=' - this makes CondRefOf(_OSI, Local0) TRUE
2. 'acpi_osi="Windows"' - this makes \_OSI("Windows") TRUE
3. 'acpi_osi="!Windows"' - this makes \_OSI("Windows") FALSE
The function to implement this feature is also used as a quirk mechanism
in the Linux ACPI subystem.
When _OSI is evaluatated by the AML codes, ACPICA replies "SUPPORTED"
to all Windows operating system vendor strings. This is because
Windows operating systems return "SUPPORTED" if the argument to the
_OSI method specifies an earlier version of Windows. Please refer to
the following MSDN document:
How to Identify the Windows Version in ACPI by Using _OSI
http://msdn.microsoft.com/en-us/library/hardware/gg463275.aspx
This adds difficulties when developers want to feed specific Windows
operating system vendor string to the BIOS codes for debugging
purpose, multiple acpi_osi="!xxx" have to be specified in the command
line to force Linux replying "UNSUPPORTED" to the Windows OS vendor
strings listed in the AML codes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull block IO driver bits from Jens Axboe:
"As I mentioned in the core block pull request, due to real life
circumstances the driver pull request would be late. Now it looks
like -rc2 late... On the plus side, apart form the rsxx update, these
are all things that I could argue could go in later in the cycle as
they are fixes and not features. So even though things are late, it's
not ALL bad.
The pull request contains:
- Updates to bcache, all bug fixes, from Kent.
- A pile of drbd bug fixes (no big features this time!).
- xen blk front/back fixes.
- rsxx driver updates, some of them deferred form 3.10. So should be
well cooked by now"
* 'for-3.11/drivers' of git://git.kernel.dk/linux-block: (63 commits)
bcache: Allocation kthread fixes
bcache: Fix GC_SECTORS_USED() calculation
bcache: Journal replay fix
bcache: Shutdown fix
bcache: Fix a sysfs splat on shutdown
bcache: Advertise that flushes are supported
bcache: check for allocation failures
bcache: Fix a dumb race
bcache: Use standard utility code
bcache: Update email address
bcache: Delete fuzz tester
bcache: Document shrinker reserve better
bcache: FUA fixes
drbd: Allow online change of al-stripes and al-stripe-size
drbd: Constants should be UPPERCASE
drbd: Ignore the exit code of a fence-peer handler if it returns too late
drbd: Fix rcu_read_lock balance on error path
drbd: fix error return code in drbd_init()
drbd: Do not sleep inside rcu
bcache: Refresh usage docs
...
This elaborates a bit on the pin control and pin muxing
logic vs GPIO arangements in the hardware.
Inspired by some drawings in a mail from Christian Ruppert.
Both arrangements are confirmed to exist in practice.
Cc: Rob Landley <rob@landley.net>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This prefix will be used in various compatible properties
for the devices from Qualcomm Atheros, Inc.
Cc: Luis R. Rodriguez <rodrigue@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
CONFIG_ARCH_MEMORY_PROBE enables the
/sys/devices/system/memory/probe interface, which allows a given
memory address to be hot-added as follows:
# echo start_address_of_new_memory > /sys/devices/system/memory/probe
(See Documentation/memory-hotplug.txt for more details.)
This probe interface is required on powerpc. On x86, however,
ACPI notifies a memory hotplug event to the kernel, which
performs its hotplug operation as the result.
Therefore, regular users do not need this interface on x86. This probe
interface is also error-prone and misleading that the kernel blindly
adds a given memory address without checking if the memory is present
on the system; no probing is done despite of its name.
The kernel crashes when a user requests to online a memory block
that is not present on the system. This interface is currently
used for testing as it can fake a hotplug event.
This patch disables CONFIG_ARCH_MEMORY_PROBE by default on x86,
adds its Kconfig menu entry on x86, and clarifies its use in
Documentation/ memory-hotplug.txt.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: linux-mm@kvack.org
Cc: dave@sr71.net
Cc: isimatu.yasuaki@jp.fujitsu.com
Cc: tangchen@cn.fujitsu.com
Cc: vasilis.liaskovitis@profitbricks.com
Link: http://lkml.kernel.org/r/1374256068-26016-1-git-send-email-toshi.kani@hp.com
[ Edited it slightly. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The property name to pass names for interrupt resources is called
"interrupt-names", not "interrupt-name". Fix it to avoid further
confusion.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the DT bindings documentation with the interrupt-controller
and #interrupt-cells properties.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the low-power Powerdown Controller GPIOs in the
TZ1090 SoC.
The driver is instantiated by device tree and supports interrupts for
the SysWake GPIOs only.
Changes in v4:
- fix typos in DT bindings compatible properties
- reference Documentation/devicetree/bindings/gpio/gpio.txt in
gpio-ranges description in DT bindings
- fix gpio-ranges examples in DT bindings (it must now have 3 cells)
Changes in v3:
- separated from irq-imgpdc and removed arch/metag changes to allow
these patches to go upstream separately via the pinctrl[/gpio] trees
(particularly the pinctrl drivers depend on the new pinconf DT
bindings).
- some s/unsigned/unsigned int/.
- gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
<dt-bindings/interrupt-controller/irq.h> flags in bindings.
- gpio-tz1090*: move initcall from postcore to subsys.
Changes in v2:
- gpio-tz1090-pdc: remove references to Linux flags in dt bindings
- gpio-tz1090-pdc: make use of BIT() from linux/bitops.h
- gpio-tz1090-pdc: make register accessors inline to match pinctrl
- gpio-tz1090-pdc: update gpio-ranges to use 3 cells after recent ABI
breakage
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the main GPIOs found in the TZ1090 (Comet) SoC.
This doesn't include low-power GPIOs as they're controlled separately
via the Powerdown Controller (PDC) registers.
The driver is instantiated by device tree and supports interrupts for
all GPIOs.
Changes in v4:
- fix typos in DT bindings compatible properties
- reference Documentation/devicetree/bindings/gpio/gpio.txt in
gpio-ranges description in DT bindings
- fix gpio-ranges examples in DT bindings (it must now have 3 cells)
- gpio-tz1090: use of_property_read_u32 instead of of_get_property
Changes in v3:
- separated from irq-imgpdc and removed arch/metag changes to allow
these patches to go upstream separately via the pinctrl[/gpio] trees
(particularly the pinctrl drivers depend on the new pinconf DT
bindings).
- some s/unsigned/unsigned int/.
- some s/unsigned int/bool/ and use of BIT().
- gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
<dt-bindings/interrupt-controller/irq.h> flags in bindings.
- gpio-tz1090*: move initcall from postcore to subsys.
- gpio-tz1090: add REG_ prefix to some constants for consistency.
- gpio-tz1090: add comment to explain tz1090_gpio_irq_next_edge
cunningness.
Changes in v2:
- gpio-tz1090: remove references to Linux flags in dt bindings
- gpio-tz1090: make use of BIT() from linux/bitops.h
- gpio-tz1090: make register accessors inline to match pinctrl
- gpio-tz1090: update gpio-ranges to use 3 cells after recent ABI
breakage
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the regulator driver for PMIC 88pm800 including device tree
support.
88pm800 is an I2C-based power-management IC containing voltage
regulators, a real-time clock, and some general purpose ADC devices,
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add wm8904 based audio machine driver for Atmel EK board
The following ek board based on it
- at91sam9n12ek
- sama5d3xek (d31, d33, d34, d35)
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds an clocksource driver for the main timer(s)
found on MOXA ART SoCs.
The MOXA ART SoC provides three separate timers with individual
count/load/match registers, two are used here:
TIMER1: clockevents, used to support oneshot and periodic events
TIMER2: set up as a free running counter, used as clocksource
Timers are preconfigured by bootloader to count down and interrupt
on match or zero. Count increments every APB clock cycle and is
automatically reloaded when it reaches zero.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
commit 28d1e8cd67
(regulator: palma: add ramp delay support through regulator constraints)
Removed the regulator's ti,step option from driver without updating the
documentation.
So, remove from documentation and example as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
commit 3c870e3f9d
(regulator: palmas: Change the DT node property names to follow the convention)
Missed updating mode-sleep from sleep-mode. Fix the same.
Documentation example seems proper for this property.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Re-phrase the explanations on the sorting of search results, in a more
concise and complete way.
Drop reference to the user's locale when sorting alphabetically, since
this is implicit.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
The driver supports a range of devices but currently doesn't allow those
device names to be used for enumeration on DT. Add the currently listed
I2C IDs as compatible strings.
Signed-off-by: Mark Brown <broonie@linaro.org>
It is somewhat strange that the default value to support the
depracated interface is set (1).
Anyway this has existed for years. The previous patch already
removed the functionality to still export events through /proc.
Now this param is useless and should vanish too.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is quite some time that this one has been deprecated.
Get rid of it.
Should some really important user be overseen, it may be reverted and
the userspace program worked on first, but it is time to do something
to get rid of this old stuff...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some hardwares support disabling ramp delay, so adding ramp_disable flag to
constraints. It will be used to figure out whether ramp_delay in constraints
is explicitly set to zero or its unintialized (zero by default).
And we don't need to call set_voltage_time_sel() for regulators for whom ramp
delay is disabled in constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fsl-ssi was located in powerpc/fsl/ssi.txt. This is no powerpc specific
device, so it should be moved to sound/ as it connects to differen audio
codecs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support for loading the ak4554 codec module via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spll_gate was added with commit b7eed20761
"ARM: imx27: add a clock gate to activate SPLL clock".
spll_gate is missing in the devicetree clock documentation for imx27. This
patch adds it to the list of clocks in the documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the uses of the __cpuinit macros from C files in
the core kernel directories (kernel, init, lib, mm, and include)
that don't really have a specific maintainer.
[1] https://lkml.org/lkml/2013/5/20/589
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull x86 platform driver updates from Matthew Garrett:
"Nothing overly exciting here - a couple of new drivers that don't do a
great deal, along with some miscellaneous fixes and a couple of small
feature enablement patches"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
x86 platform drivers: fix gpio leak
toshiba_acpi: Add dependency on SERIO_I8042
asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. 1015E/U
Add trivial driver to disable Intel Smart Connect
Add support driver for Intel Rapid Start Technology
hp-wmi: add supports for POST code error
asus-wmi: control wlan-led only if wapf == 4
drivers/platform/x86/intel_ips: Convert to module_pci_driver
asus-nb-wmi: ignore ALS notification key code
asus-wmi: append newline to messages
x86: asus-laptop: fix invalid point access
x86: msi-laptop: fix memleak
amilo-rfkill: Add dependency on SERIO_I8042
dell-laptop: fix error return code in dell_init()
hp-wmi: Enable hotkeys on some systems
Pull second round of input updates from Dmitry Torokhov:
"An update to Elantech driver to support hardware v7, fix to the new
cyttsp4 driver to use proper addressing, ads7846 device tree support
and nspire-keypad got a small cleanup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: nspire-keypad - replace magic offset with define
Input: elantech - fix for newer hardware versions (v7)
Input: cyttsp4 - use 16bit address for I2C/SPI communication
Input: ads7846 - add device tree bindings
Input: ads7846 - make sure we do not change platform data
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
Pull timer updates from Thomas Gleixner:
- watchdog fixes for full dynticks
- improved debug output for full dynticks
- remove an obsolete full dynticks check
- two ARM SoC clocksource drivers for sharing across SoCs
- tick broadcast fix for CPU hotplug
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: broadcast: Check broadcast mode on CPU hotplug
clocksource: arm_global_timer: Add ARM global timer support
clocksource: Add Marvell Orion SoC timer
nohz: Remove obsolete check for full dynticks CPUs to be RCU nocbs
watchdog: Boot-disable by default on full dynticks
watchdog: Rename confusing state variable
watchdog: Register / unregister watchdog kthreads on sysctl control
nohz: Warn if the machine can not perform nohz_full
Pull perf fixes from Thomas Gleixner:
- fix for do_div() abuse on x86
- locking fix in perf core
- a pile of (build) fixes and cleanups in perf tools
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
perf/x86: Fix incorrect use of do_div() in NMI warning
perf: Fix perf_lock_task_context() vs RCU
perf: Remove WARN_ON_ONCE() check in __perf_event_enable() for valid scenario
perf: Clone child context from parent context pmu
perf script: Fix broken include in Context.xs
perf tools: Fix -ldw/-lelf link test when static linking
perf tools: Revert regression in configuration of Python support
perf tools: Fix perf version generation
perf stat: Fix per-socket output bug for uncore events
perf symbols: Fix vdso list searching
perf evsel: Fix missing increment in sample parsing
perf tools: Update symbol_conf.nr_events when processing attribute events
perf tools: Fix new_term() missing free on error path
perf tools: Fix parse_events_terms() segfault on error path
perf evsel: Fix count parameter to read call in event_format__new
perf tools: fix a typo of a Power7 event name
perf tools: Fix -x/--exclude-other option for report command
perf evlist: Enhance perf_evlist__start_workload()
perf record: Remove -f/--force option
perf record: Remove -A/--append option
...
- AF_IB (native IB addressing) for CMA from Sean Hefty
- New mlx5 driver for Mellanox Connect-IB adapters (including post merge request fixes)
- SRP fixes from Bart Van Assche (including fix to first merge request)
- qib HW driver updates
- Resurrection of ocrdma HW driver development
- uverbs conversion to create fds with O_CLOEXEC set
- Other small changes and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nZh8
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- AF_IB (native IB addressing) for CMA from Sean Hefty
- new mlx5 driver for Mellanox Connect-IB adapters (including post
merge request fixes)
- SRP fixes from Bart Van Assche (including fix to first merge request)
- qib HW driver updates
- resurrection of ocrdma HW driver development
- uverbs conversion to create fds with O_CLOEXEC set
- other small changes and fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
mlx5: Return -EFAULT instead of -EPERM
IB/qib: Log all SDMA errors unconditionally
IB/qib: Fix module-level leak
mlx5_core: Adjust hca_cap.uar_page_sz to conform to Connect-IB spec
IB/srp: Let srp_abort() return FAST_IO_FAIL if TL offline
IB/uverbs: Use get_unused_fd_flags(O_CLOEXEC) instead of get_unused_fd()
mlx5_core: Fixes for sparse warnings
IB/mlx5: Make profile[] static in main.c
mlx5: Fix parameter type of health_handler_t
mlx5: Add driver for Mellanox Connect-IB adapters
IB/core: Add reserved values to enums for low-level driver use
IB/srp: Bump driver version and release date
IB/srp: Make HCA completion vector configurable
IB/srp: Maintain a single connection per I_T nexus
IB/srp: Fail I/O fast if target offline
IB/srp: Skip host settle delay
IB/srp: Avoid skipping srp_reset_host() after a transport error
IB/srp: Fix remove_one crash due to resource exhaustion
IB/qib: New transmitter tunning settings for Dell 1.1 backplane
IB/core: Fix error return code in add_port()
...
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
- fix for xfs_fsr returning -EINVAL
- cleanup in xfs_bulkstat
- cleanup in xfs_open_by_handle
- update mount options documentation
- clean up local format handling in xfs_bmapi_write
- fix dquot log reservations which were too small
- fix sgid inheritance for subdirectories when default acls are in use
- add project quota fields to various structures
- fix teardown of quotainfo structures when quotas are turned off
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=QiZy
-----END PGP SIGNATURE-----
Merge tag 'for-linus-v3.11-rc1-2' of git://oss.sgi.com/xfs/xfs
Pull more xfs updates from Ben Myers:
"Here are a fix for xfs_fsr, a cleanup in bulkstat, a cleanup in
xfs_open_by_handle, updated mount options documentation, a cleanup in
xfs_bmapi_write, a fix for the size of dquot log reservations, a fix
for sgid inheritance when acls are in use, a fix for cleaning up
quotainfo structures, and some more of the work which allows group and
project quotas to be used together.
We had a few more in this last quota category that we might have liked
to get in, but it looks there are still a few items that need to be
addressed.
- fix for xfs_fsr returning -EINVAL
- cleanup in xfs_bulkstat
- cleanup in xfs_open_by_handle
- update mount options documentation
- clean up local format handling in xfs_bmapi_write
- fix dquot log reservations which were too small
- fix sgid inheritance for subdirectories when default acls are in use
- add project quota fields to various structures
- fix teardown of quotainfo structures when quotas are turned off"
* tag 'for-linus-v3.11-rc1-2' of git://oss.sgi.com/xfs/xfs:
xfs: Fix the logic check for all quotas being turned off
xfs: Add pquota fields where gquota is used.
xfs: fix sgid inheritance for subdirectories inheriting default acls [V3]
xfs: dquot log reservations are too small
xfs: remove local fork format handling from xfs_bmapi_write()
xfs: update mount options documentation
xfs: use get_unused_fd_flags(0) instead of get_unused_fd()
xfs: clean up unused codes at xfs_bulkstat()
xfs: use XFS_BMAP_BMDR_SPACE vs. XFS_BROOT_SIZE_ADJ
This patch adds the driver for the watchdog devices found on MEN Mikro
Elektronik A21 VMEbus CPU Carrier Boards. It has DT-support and uses the
watchdog framework.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a driver for watchdog timer hardware present on Broadcom BCM2835 SoC,
used in Raspberry Pi and Roku 2 devices.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
framework for storage arrays that dynamically reconfigure their
preferred paths for different device regions.
Fix a bug in the verity target that prevented its use with some
specific sizes of devices.
Improve some locking mechanisms in the device-mapper core and bufio.
Add Mike Snitzer as a device-mapper maintainer.
A few more clean-ups and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s5m4
-----END PGP SIGNATURE-----
Merge tag 'dm-3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper changes from Alasdair G Kergon:
"Add a device-mapper target called dm-switch to provide a multipath
framework for storage arrays that dynamically reconfigure their
preferred paths for different device regions.
Fix a bug in the verity target that prevented its use with some
specific sizes of devices.
Improve some locking mechanisms in the device-mapper core and bufio.
Add Mike Snitzer as a device-mapper maintainer.
A few more clean-ups and fixes"
* tag 'dm-3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: add switch target
dm: update maintainers
dm: optimize reorder structure
dm: optimize use SRCU and RCU
dm bufio: submit writes outside lock
dm cache: fix arm link errors with inline
dm verity: use __ffs and __fls
dm flakey: correct ctr alloc failure mesg
dm verity: remove pointless comparison
dm: use __GFP_HIGHMEM in __vmalloc
dm verity: fix inability to use a few specific devices sizes
dm ioctl: set noio flag to avoid __vmalloc deadlock
dm mpath: fix ioctl deadlock when no paths
Pull core block IO updates from Jens Axboe:
"Here are the core IO block bits for 3.11. It contains:
- A tweak to the reserved tag logic from Jan, for weirdo devices with
just 3 free tags. But for those it improves things substantially
for random writes.
- Periodic writeback fix from Jan. Marked for stable as well.
- Fix for a race condition in IO scheduler switching from Jianpeng.
- The hierarchical blk-cgroup support from Tejun. This is the grunt
of the series.
- blk-throttle fix from Vivek.
Just a note that I'm in the middle of a relocation, whole family is
flying out tomorrow. Hence I will be awal the remainder of this week,
but back at work again on Monday the 15th. CC'ing Tejun, since any
potential "surprises" will most likely be from the blk-cgroup work.
But it's been brewing for a while and sitting in my tree and
linux-next for a long time, so should be solid."
* 'for-3.11/core' of git://git.kernel.dk/linux-block: (36 commits)
elevator: Fix a race in elevator switching
block: Reserve only one queue tag for sync IO if only 3 tags are available
writeback: Fix periodic writeback after fs mount
blk-throttle: implement proper hierarchy support
blk-throttle: implement throtl_grp->has_rules[]
blk-throttle: Account for child group's start time in parent while bio climbs up
blk-throttle: add throtl_qnode for dispatch fairness
blk-throttle: make throtl_pending_timer_fn() ready for hierarchy
blk-throttle: make tg_dispatch_one_bio() ready for hierarchy
blk-throttle: make blk_throtl_bio() ready for hierarchy
blk-throttle: make blk_throtl_drain() ready for hierarchy
blk-throttle: dispatch from throtl_pending_timer_fn()
blk-throttle: implement dispatch looping
blk-throttle: separate out throtl_service_queue->pending_timer from throtl_data->dispatch_work
blk-throttle: set REQ_THROTTLED from throtl_charge_bio() and gate stats update with it
blk-throttle: implement sq_to_tg(), sq_to_td() and throtl_log()
blk-throttle: add throtl_service_queue->parent_sq
blk-throttle: generalize update_disptime optimization in blk_throtl_bio()
blk-throttle: dispatch to throtl_data->service_queue.bio_lists[]
blk-throttle: move bio_lists[] and friends to throtl_service_queue
...
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull thermal management updates from Zhang Rui:
"There are not too many changes this time, except two new platform
thermal drivers, ti-soc-thermal driver and x86_pkg_temp_thermal
driver, and a couple of small fixes.
Highlights:
- move the ti-soc-thermal driver out of the staging tree to the
thermal tree.
- introduce the x86_pkg_temp_thermal driver. This driver registers
CPU digital temperature package level sensor as a thermal zone.
- small fixes/cleanups including removing redundant use of
platform_set_drvdata() and of_match_ptr for all platform thermal
drivers"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: cpu_cooling: fix stub function
thermal: ti-soc-thermal: use standard GPIO DT bindings
thermal: MAINTAINERS: Add git tree path for SoC specific updates
thermal: fix x86_pkg_temp_thermal.c build and Kconfig
Thermal: Documentation for x86 package temperature thermal driver
Thermal: CPU Package temperature thermal
thermal: consider emul_temperature while computing trend
thermal: ti-soc-thermal: add DT example for DRA752 chip
thermal: ti-soc-thermal: add dra752 chip to device table
thermal: ti-soc-thermal: add thermal data for DRA752 chips
thermal: ti-soc-thermal: remove usage of IS_ERR_OR_NULL
thermal: ti-soc-thermal: freeze FSM while computing trend
thermal: ti-soc-thermal: remove external heat while extrapolating hotspot
thermal: ti-soc-thermal: update DT reference for OMAP5430
x86, mcheck, therm_throt: Process package thresholds
thermal: cpu_cooling: fix 'descend' check in get_property()
Thermal: spear: Remove redundant use of of_match_ptr
Thermal: kirkwood: Remove redundant use of of_match_ptr
Thermal: dove: Remove redundant use of of_match_ptr
Thermal: armada: Remove redundant use of of_match_ptr
...
were added to 3.10, which includes several bug fixes that have been
marked for stable.
As for new features, there were a few, but nothing to write to LWN about.
These include:
New function trigger called "dump" and "cpudump" that will cause
ftrace to dump its buffer to the console when the function is called.
The difference between "dump" and "cpudump" is that "dump" will dump
the entire contents of the ftrace buffer, where as "cpudump" will only
dump the contents of the ftrace buffer for the CPU that called the function.
Another small enhancement is a new sysctl switch called "traceoff_on_warning"
which, when enabled, will disable tracing if any WARN_ON() is triggered.
This is useful if you want to debug what caused a warning and do not
want to risk losing your trace data by the ring buffer overwriting the
data before you can disable it. There's also a kernel command line
option that will make this enabled at boot up called the same thing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJR1uF2AAoJEOdOSU1xswtMJ1IH/2LSiZAKTA2QaRgGQC/5Bb9c
XSOI1HfD/78lmUvTyb0AX8sLpkzZlvIONEQ/WaZUFo1Zjbrl45zJUwMkTE9uImEg
ZqI5x8OiiN6j4XrRbfYn3Ti060H/Jq41pZXa+shh961Vv51ilv/1yyLkoRmnjzuO
JTloPdXDV7icOqqiSdgxSdtUSv59Ef1ZdHgvvsb3aqzMC5btVQPi4kIys0ST1Tr1
pMWBY+UgvH0xYm3gvTR+W6jjDlkVZEH2alkmcinfr+uC1tm9DDqK2HA17Pd5yZ5z
HNdT76lCzf9iqRF5F8HUvUt+PIp76dNNxAt2qpB6APqAuJTojyguxXHDbY/0kzs=
=UvLi
-----END PGP SIGNATURE-----
Merge tag 'trace-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing changes from Steven Rostedt:
"The majority of the changes here are cleanups for the large changes
that were added to 3.10, which includes several bug fixes that have
been marked for stable.
As for new features, there were a few, but nothing to write to LWN
about. These include:
New function trigger called "dump" and "cpudump" that will cause
ftrace to dump its buffer to the console when the function is called.
The difference between "dump" and "cpudump" is that "dump" will dump
the entire contents of the ftrace buffer, where as "cpudump" will only
dump the contents of the ftrace buffer for the CPU that called the
function.
Another small enhancement is a new sysctl switch called
"traceoff_on_warning" which, when enabled, will disable tracing if any
WARN_ON() is triggered. This is useful if you want to debug what
caused a warning and do not want to risk losing your trace data by the
ring buffer overwriting the data before you can disable it. There's
also a kernel command line option that will make this enabled at boot
up called the same thing"
* tag 'trace-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (34 commits)
tracing: Make tracing_open_generic_{tr,tc}() static
tracing: Remove ftrace() function
tracing: Remove TRACE_EVENT_TYPE enum definition
tracing: Make tracer_tracing_{off,on,is_on}() static
tracing: Fix irqs-off tag display in syscall tracing
uprobes: Fix return value in error handling path
tracing: Fix race between deleting buffer and setting events
tracing: Add trace_array_get/put() to event handling
tracing: Get trace_array ref counts when accessing trace files
tracing: Add trace_array_get/put() to handle instance refs better
tracing: Protect ftrace_trace_arrays list in trace_events.c
tracing: Make trace_marker use the correct per-instance buffer
ftrace: Do not run selftest if command line parameter is set
tracing/kprobes: Don't pass addr=ip to perf_trace_buf_submit()
tracing: Use flag buffer_disabled for irqsoff tracer
tracing/kprobes: Turn trace_probe->files into list_head
tracing: Fix disabling of soft disable
tracing: Add missing syscall_metadata comment
tracing: Simplify code for showing of soft disabled flag
tracing/kprobes: Kill probe_enable_lock
...
Merge more patches from Andrew Morton:
"The rest of MM"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: remove free_area_cache
zswap: add documentation
zswap: add to mm/
zbud: add to mm/
Mark Brown