Split up crtc_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:
@@
struct intel_crtc_state *T;
@@
-T->base
+T->uapi
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-5-maarten.lankhorst@linux.intel.com
This slightly simplifies the EHL DPLL4 handling and also gives us more
flexibility in the future in case we need to skip the use of specific
PLL's (e.g., due to hardware workarounds and such).
v2:
- Replace GENMASK() with or'd BIT()'s to make the specific DPLLs more
explicit. (Ville)
- s/unsigned/unsigned long/. (Lucas)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191008172920.11362-1-matthew.d.roper@intel.com
The Thunderbolt PLL divider values on TGL differ from the ICL ones,
update the PLL parameter calculation function accordingly.
Bspec: 49204
v2:
- Remove unused refclk config. (José)
Cc: Jose Souza <jose.souza@intel.com>
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Westerberg <mika.westerberg@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jose Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002204108.32242-1-imre.deak@intel.com
Link training is failling when running link at 2.7GHz and 1.62GHz and
following BSpec pll algorithm.
Comparing the values calculated and the ones from the reference table
it looks like MG_CLKTOP2_CORECLKCTL1_A_DIVRATIO should not always set
to 5. For DP ports ICL mg pll algorithm sets it to 10 or 5 based on
div2 value, that matches with dkl hardcoded table.
So implementing this way as it proved to work in HW and leaving a
comment so we know why it do not match BSpec.
v4:
Using the same is_dp check as ICL, need testing on HDMI over tc port
Issue reported on BSpec 49204.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-3-jose.souza@intel.com
Extending ICL mg calculations to also support dkl calculations.
v3:
Fixing iref_trim calculation for 38400 refclock
BSpec: 49204
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-5-jose.souza@intel.com
The final save operation into pll_state of the calculations done will
be different for DKL PHY. Prepare for that by reindenting code so it's
easier to check for correctness. This one has no change in behavior.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-4-jose.souza@intel.com
Add a new function to write to dkl phy pll registers. As per the
bspec all the registers are read modify write.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-2-jose.souza@intel.com
The disable function can be the same as for MG phy since the same
registers are used. The others are different as registers changed,
also adding a empty dkl_pll_write() to be implemented later.
v2:
Setting the right HIP_INDEX_REG bits (José)
v3:
Masking non-computed registers of mg_pll_tdc_coldst_bias
when getting hardware state
Sharing mg_pll_enable() with TGL
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-1-jose.souza@intel.com
Commit 24a7bfe0c2 ("drm/i915: Keep the TypeC port mode fixed when the
port is active") added this new hook while in parallel TGL upstream was
happening and this was missed.
Without this driver will crash when TC DDI is added and driver is
preparing to do a full modeset.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-4-jose.souza@intel.com
enum port is a mess now because it no longer matches the spec
at all. Let's start to dig ourselves out of this hole by
reducing our reliance on port_name(). This should at least make
a bunch of debug messages a bit more sensible while we think how
to fill the the hole properly.
Based on the following cocci script with a lot of manual cleanup
(all the format strings etc.):
@@
expression E;
@@
(
- port_name(E->port)
+ E->base.base.id, E->base.name
|
- port_name(E.port)
+ E.base.base.id, E.base.name
)
@@
enum port P;
expression E;
@@
P = E->port
<...
- port_name(P)
+ E->base.base.id, E->base.name
...>
@@
enum port P;
expression E;
@@
P = E.port
<...
- port_name(P)
+ E.base.base.id, E.base.name
...>
@@
expression E;
@@
{
- enum port P = E;
... when != P
}
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830182719.32608-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
To reduce the number of explicit dev_priv->uncore calls in the display
code ahead of the introduction of dev_priv->de_uncore, this patch
introduces a wrapper for one of the main usages of it, the register
waits. When we transition to the new uncore, we can just update the
wrapper to point to the appropriate structure.
Since the vast majority of waits are on a set or clear of a bit or mask,
add set & clear flavours of the wrapper to simplify the code.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816012343.36433-7-daniele.ceraolospurio@intel.com
Everything about the file is about display, and mostly about types
related to display. Move under display/ as intel_display_types.h to
reflect the facts.
There's still plenty to clean up, but start off with moving the file
where it logically belongs and naming according to contents.
v2: fix the include guard name in the renamed file
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806113933.11799-1-jani.nikula@intel.com
Although, DPLL4 enable and disable is associated with MGPLL1_ENABLE
register, we can use ICL_DPLL_CFGCR0/CR1 macros to access this dpll's
CR0 and CR1 registers by passing an id of 4 to these macros.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717021316.18610-1-vivek.kasireddy@intel.com
On TGL the port programming for combophy is very similar to ICL, so
adapt the callers to possibly use the different register values.
v2 (Lucas): Add TODO with about DPLL4 (requested by Ville)
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-21-lucas.demarchi@intel.com
Add a new pll array for Tiger Lake. The TC pll functions for type C will
be covered in later patches after its phy is implemented.
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-12-lucas.demarchi@intel.com
Transition the remaining uses of intel_port_is_* over to the equivalent
intel_phy_is_* functions and drop the port functions.
v5: Fix a call in a debug function that's only called when
CONFIG_DRM_I915_DEBUG_RUNTIME_PM is on. (CI)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-5-matthew.d.roper@intel.com
For consistency clear the icl_port_dplls from the new crtc state, when
releasing the DPLLs from the old crtc state. Leaving them set could
result in releasing the same PLLs multiple times from the same CRTC
state incorrectly (if the same CRTC was first used for a TypeC port then
for a combo PHY port).
Leaving the stale pointers behind happens not to cause a problem atm
(since the incorrect releasing will be a NOP), but we need to fix that
for consistency.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708140735.20198-2-imre.deak@intel.com
For symmetry with the get_dplls() hook which sets the shared_dpll
pointer clear the same pointer from the put_dplls() hook.
While at it also constify the old crtc state.
v2:
- Constify the old crtc state. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708140735.20198-1-imre.deak@intel.com
This patch adds support for DPLL4 on EHL that include the
following restrictions:
- DPLL4 cannot be used with DDIA (combo port A internal eDP usage).
DPLL4 can be used with other DDIs, including DDID
(combo port A external usage).
- DPLL4 cannot be enabled when DC5 or DC6 are enabled.
- The DPLL4 enable, lock, power enabled, and power state are connected
to the MGPLL1_ENABLE register.
v2: (suggestions from Bob Paauwe)
- Rework ehl_get_dpll() function to call intel_find_shared_dpll() and
iterate twice: once for Combo plls and once for MG plls.
- Use MG pll funcs for DPLL4 instead of creating new ones and modify
mg_pll_enable to include the restrictions for EHL.
v3: Fix compilation error
v4: (suggestions from Lucas and Ville)
- Treat DPLL4 as a combo phy PLL and not as MG PLL
- Disable DC states when this DPLL is being enabled
- Reuse icl_get_dpll instead of creating a separate one for EHL
v5: (suggestion from Ville)
- Refcount the DC OFF power domains during the enabling and disabling
of this DPLL.
v6: rebase
v7: (suggestion from Imre)
- Add a new power domain instead of iterating over the domains
assoicated with DC OFF power well.
v8: (Ville and Imre)
- Rename POWER_DOMAIN_DPLL4 TO POWER_DOMAIN_DPLL_DC_OFF
- Grab a reference in intel_modeset_setup_hw_state() if this
DPLL was already enabled perhaps by BIOS.
- Check for the port type instead of the encoder
v9: (Ville)
- Move the block of code that grabs a reference to the power domain
POWER_DOMAIN_DPLL_DC_OFF to intel_modeset_readout_hw_state() to ensure
that there is a reference present before this DPLL might get disabled.
v10: rebase
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703230353.24059-1-vivek.kasireddy@intel.com
icl-dsi is dying on suspend/resume at
RIP: 0010:icl_update_active_dpll+0x2c/0xa0 [i915]
which appears due to the loss of the time primary_port across suspend.
Protect against the potential NULL dereference by assuming
ICL_PORT_DPLL_DEFAULT unless the port is actively specified otherwise.
Fixes: 24a7bfe0c2 ("drm/i915: Keep the TypeC port mode fixed when the port is active")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702140950.7069-1-chris@chris-wilson.co.uk
The TypeC port mode needs to stay fixed whenever the port is active. Do
that by introducing a tc_link_refcount to account for active ports,
avoiding changing the port mode if a reference is held.
During the modeset commit phase we also have to reset the port mode and
update the active PLL reflecting the new port mode. We can do this only
once the port and its old PLL has been already disabled. Add the new
encoder update_prepare/complete hooks that are called around the whole
enabling sequence. The TypeC specific hooks of these will reset the port
mode, update the active PLL if the port will be active and ensure that
the port mode will stay fixed for the duration of the whole enabling
sequence by holding a tc_link_refcount.
During the port enabling, the pre_pll_enable/post_pll_disable hooks will
take/release a tc_link_refcount to ensure the port mode stays fixed
while the port is active.
Changing the port mode should also be avoided during connector detection
and AUX transfers if the port is active, we'll do that by checking the
port's tc_link_refcount.
When resetting the port mode we also have to take into account the
maximum lanes provided by the FIA. It's guaranteed to be 4 in TBT-alt
and legacy modes, but there may be less lanes available in DP-alt mode,
in which case we have to fall back to TBT-alt mode.
While at it also update icl_tc_phy_connect()'s code comment, reflecting
the current way of switching the port mode.
v2:
- Add the update_prepare/complete hooks to the encoder instead of the
connector. (Ville)
- Simplify intel_connector_needs_modeset() by removing redundant if.
(Ville)
v3:
- Fix sparse warning, marking static functions as such.
v4:
- Rebase on drm-tip.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-21-imre.deak@intel.com
When enabling a TypeC port we need to reserve all the required PLLs for
it, the TBT PLL for TBT-alt and the MG PHY PLL for DP-alt/legacy sinks.
We can select the proper PLL for the current port mode from the reserved
PLLs only once we selected and locked down the port mode for the whole
duration of the port's active state. Resetting and locking down the port
mode can in turn happen only during the modeset commit phase once we
disabled the given port and the PLL it used.
To support the above reserve-and-select PLL semantic we store the
reserved PLLs along with their HW state in the CRTC state and provide a
way to select the active PLL from these. The selected PLL along with its
HW state will be pointed at by crtc_state->shared_dpll/dpll_hw_state as
in the case of other port types.
Besides reserving all required PLLs no functional changes.
v2:
- Fix releasing the ICL PLLs, not clearing the PLLs from the old
crtc_state.
- Init port_dpll to ICL_PORT_DPLL_DEFAULT closer to where port_dpll is
used for symmetry with the corresponding ICL_PORT_DPLL_MG_PHY init.
(Ville)
v3:
- Add FIXME: for clearing the ICL port PLLs from the new crtc state.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-20-imre.deak@intel.com
For clarity factor out the combo PHY and TypeC PHY specific code from
icl_get_dplls() into their own functions.
No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-19-imre.deak@intel.com
Pass the PLL HW state to the PLL find/reference functions making it
clearer what is their input. Also pass to these the atomic state and the
CRTC object instead of the CRTC state, since they don't require the
latter.
Move setting the PLL in the crtc_state to the get_dpll() hook, which
is the more logical place for this, where the related PLL HW state was also
set.
This refactoring is also a preparation for a follow-up patch that will
have to find/reference multiple PLLs.
No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-18-imre.deak@intel.com
For consistency s/intel_get_shared_dpll()/intel_reserve_shared_dplls()/
to better match intel_release_shared_dplls(). Also, pass to the
reserve/release and get_dplls/put_dplls hooks the intel_atomic_state and
CRTC object, that way these functions can look up the old or new state
as needed.
Also release the PLLs from the atomic state via a new
put_dplls->intel_unreference_shared_dpll() call chain for better
symmetry with the reservation via the
get_dplls->intel_reference_shared_dpll() call chain.
Since nothing uses the PLL returned by intel_reserve_shared_dplls(),
make it return only a bool.
While at it also clarify the reserve/release function docbook headers
making it clear that multiple DPLLs will be reserved/released and
whether the new or old atomic CRTC state is affected.
This refactoring is also a preparation for a follow-up change that needs
to reserve multiple DPLLs.
Kudos to Ville for the idea to pass intel_atomic_state around, to make
things clearer locally where an object's old/new atomic state is
required.
No functional changes.
v2:
- Fix checkpatch issue: typo in code comment.
v3:
- Rebase on drm-tip.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-17-imre.deak@intel.com
The TypeC port mode can switch dynamically, to reflect that better call
the port's mode as 'mode' rather than 'type'.
While at it:
- s/TC_PORT_TBT/TC_PORT_TBT_ALT/ and s/TC_PORT_TYPEC/TC_PORT_DP_ALT/.
'TYPEC' is ambiguous, TBT_ALT and DP_ALT better match the reality.
- Remove the 'unknown' TypeC port mode. The mode is always known, it's
the TBT-alt/safe mode after HW reset and after disconnecting the PHY.
Simplify the tc_port/tc_type checks accordingly.
- Don't WARN if the port mode changes, that can happen normally.
No functional changes.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-5-imre.deak@intel.com
Now that we have a new subdirectory for display code, continue by moving
modesetting core code.
display/intel_frontbuffer.h sticks out like a sore thumb, otherwise this
is, again, a surprisingly clean operation.
v2:
- don't move intel_sideband.[ch] (Ville)
- use tabs for Makefile file lists and sort them
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-3-jani.nikula@intel.com
Imre Deak