Expose a new system call allowing each thread to register one userspace
memory area to be used as an ABI between kernel and user-space for two
purposes: user-space restartable sequences and quick access to read the
current CPU number value from user-space.
* Restartable sequences (per-cpu atomics)
Restartables sequences allow user-space to perform update operations on
per-cpu data without requiring heavy-weight atomic operations.
The restartable critical sections (percpu atomics) work has been started
by Paul Turner and Andrew Hunter. It lets the kernel handle restart of
critical sections. [1] [2] The re-implementation proposed here brings a
few simplifications to the ABI which facilitates porting to other
architectures and speeds up the user-space fast path.
Here are benchmarks of various rseq use-cases.
Test hardware:
arm32: ARMv7 Processor rev 4 (v7l) "Cubietruck", 2-core
x86-64: Intel E5-2630 v3@2.40GHz, 16-core, hyperthreading
The following benchmarks were all performed on a single thread.
* Per-CPU statistic counter increment
getcpu+atomic (ns/op) rseq (ns/op) speedup
arm32: 344.0 31.4 11.0
x86-64: 15.3 2.0 7.7
* LTTng-UST: write event 32-bit header, 32-bit payload into tracer
per-cpu buffer
getcpu+atomic (ns/op) rseq (ns/op) speedup
arm32: 2502.0 2250.0 1.1
x86-64: 117.4 98.0 1.2
* liburcu percpu: lock-unlock pair, dereference, read/compare word
getcpu+atomic (ns/op) rseq (ns/op) speedup
arm32: 751.0 128.5 5.8
x86-64: 53.4 28.6 1.9
* jemalloc memory allocator adapted to use rseq
Using rseq with per-cpu memory pools in jemalloc at Facebook (based on
rseq 2016 implementation):
The production workload response-time has 1-2% gain avg. latency, and
the P99 overall latency drops by 2-3%.
* Reading the current CPU number
Speeding up reading the current CPU number on which the caller thread is
running is done by keeping the current CPU number up do date within the
cpu_id field of the memory area registered by the thread. This is done
by making scheduler preemption set the TIF_NOTIFY_RESUME flag on the
current thread. Upon return to user-space, a notify-resume handler
updates the current CPU value within the registered user-space memory
area. User-space can then read the current CPU number directly from
memory.
Keeping the current cpu id in a memory area shared between kernel and
user-space is an improvement over current mechanisms available to read
the current CPU number, which has the following benefits over
alternative approaches:
- 35x speedup on ARM vs system call through glibc
- 20x speedup on x86 compared to calling glibc, which calls vdso
executing a "lsl" instruction,
- 14x speedup on x86 compared to inlined "lsl" instruction,
- Unlike vdso approaches, this cpu_id value can be read from an inline
assembly, which makes it a useful building block for restartable
sequences.
- The approach of reading the cpu id through memory mapping shared
between kernel and user-space is portable (e.g. ARM), which is not the
case for the lsl-based x86 vdso.
On x86, yet another possible approach would be to use the gs segment
selector to point to user-space per-cpu data. This approach performs
similarly to the cpu id cache, but it has two disadvantages: it is
not portable, and it is incompatible with existing applications already
using the gs segment selector for other purposes.
Benchmarking various approaches for reading the current CPU number:
ARMv7 Processor rev 4 (v7l)
Machine model: Cubietruck
- Baseline (empty loop): 8.4 ns
- Read CPU from rseq cpu_id: 16.7 ns
- Read CPU from rseq cpu_id (lazy register): 19.8 ns
- glibc 2.19-0ubuntu6.6 getcpu: 301.8 ns
- getcpu system call: 234.9 ns
x86-64 Intel(R) Xeon(R) CPU E5-2630 v3 @ 2.40GHz:
- Baseline (empty loop): 0.8 ns
- Read CPU from rseq cpu_id: 0.8 ns
- Read CPU from rseq cpu_id (lazy register): 0.8 ns
- Read using gs segment selector: 0.8 ns
- "lsl" inline assembly: 13.0 ns
- glibc 2.19-0ubuntu6 getcpu: 16.6 ns
- getcpu system call: 53.9 ns
- Speed (benchmark taken on v8 of patchset)
Running 10 runs of hackbench -l 100000 seems to indicate, contrary to
expectations, that enabling CONFIG_RSEQ slightly accelerates the
scheduler:
Configuration: 2 sockets * 8-core Intel(R) Xeon(R) CPU E5-2630 v3 @
2.40GHz (directly on hardware, hyperthreading disabled in BIOS, energy
saving disabled in BIOS, turboboost disabled in BIOS, cpuidle.off=1
kernel parameter), with a Linux v4.6 defconfig+localyesconfig,
restartable sequences series applied.
* CONFIG_RSEQ=n
avg.: 41.37 s
std.dev.: 0.36 s
* CONFIG_RSEQ=y
avg.: 40.46 s
std.dev.: 0.33 s
- Size
On x86-64, between CONFIG_RSEQ=n/y, the text size increase of vmlinux is
567 bytes, and the data size increase of vmlinux is 5696 bytes.
[1] https://lwn.net/Articles/650333/
[2] http://www.linuxplumbersconf.org/2013/ocw/system/presentations/1695/original/LPC%20-%20PerCpu%20Atomics.pdf
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Chris Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Hunter <ahh@google.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Maurer <bmaurer@fb.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-api@vger.kernel.org
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20151027235635.16059.11630.stgit@pjt-glaptop.roam.corp.google.com
Link: http://lkml.kernel.org/r/20150624222609.6116.86035.stgit@kitami.mtv.corp.google.com
Link: https://lkml.kernel.org/r/20180602124408.8430-3-mathieu.desnoyers@efficios.com
Pull workqueue updates from Tejun Heo:
- make kworkers report the workqueue it is executing or has executed
most recently in /proc/PID/comm (so they show up in ps/top)
- CONFIG_SMP shuffle to move stuff which isn't necessary for UP builds
inside CONFIG_SMP.
* 'for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: move function definitions within CONFIG_SMP block
workqueue: Make sure struct worker is accessible for wq_worker_comm()
workqueue: Show the latest workqueue name in /proc/PID/{comm,stat,status}
proc: Consolidate task->comm formatting into proc_task_name()
workqueue: Set worker->desc to workqueue name by default
workqueue: Make worker_attach/detach_pool() update worker->pool
workqueue: Replace pool->attach_mutex with global wq_pool_attach_mutex
Pull cgroup updates from Tejun Heo:
- For cpustat, cgroup has a percpu hierarchical stat mechanism which
propagates up the hierarchy lazily.
This contains commits to factor out and generalize the mechanism so
that it can be used for other cgroup stats too.
The original intention was to update memcg stats to use it but memcg
went for a different approach, so still the only user is cpustat. The
factoring out and generalization still make sense and it's likely
that this can be used for other purposes in the future.
- cgroup uses kernfs_notify() (which uses fsnotify()) to inform user
space of certain events. A rate limiting mechanism is added.
- Other misc changes.
* 'for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: css_set_lock should nest inside tasklist_lock
rdmacg: Convert to use match_string() helper
cgroup: Make cgroup_rstat_updated() ready for root cgroup usage
cgroup: Add memory barriers to plug cgroup_rstat_updated() race window
cgroup: Add cgroup_subsys->css_rstat_flush()
cgroup: Replace cgroup_rstat_mutex with a spinlock
cgroup: Factor out and expose cgroup_rstat_*() interface functions
cgroup: Reorganize kernel/cgroup/rstat.c
cgroup: Distinguish base resource stat implementation from rstat
cgroup: Rename stat to rstat
cgroup: Rename kernel/cgroup/stat.c to kernel/cgroup/rstat.c
cgroup: Limit event generation frequency
cgroup: Explicitly remove core interface files
The interrupts are enabled/disabled so the interrupt handler can run
with enabled interrupts while serving the interrupt and not lose other
interrupts especially the timer tick.
If the system runs with force-threaded interrupts then there is no need
to enable the interrupts.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
match_string() returns the index of an array for a matching string,
which can be used to simplify the code.
Link: http://lkml.kernel.org/r/1526546163-4609-1-git-send-email-xieyisheng1@huawei.com
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-06-05
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a new BPF hook for sendmsg similar to existing hooks for bind and
connect: "This allows to override source IP (including the case when it's
set via cmsg(3)) and destination IP:port for unconnected UDP (slow path).
TCP and connected UDP (fast path) are not affected. This makes UDP support
complete, that is, connected UDP is handled by connect hooks, unconnected
by sendmsg ones.", from Andrey.
2) Rework of the AF_XDP API to allow extending it in future for type writer
model if necessary. In this mode a memory window is passed to hardware
and multiple frames might be filled into that window instead of just one
that is the case in the current fixed frame-size model. With the new
changes made this can be supported without having to add a new descriptor
format. Also, core bits for the zero-copy support for AF_XDP have been
merged as agreed upon, where i40e bits will be routed via Jeff later on.
Various improvements to documentation and sample programs included as
well, all from Björn and Magnus.
3) Given BPF's flexibility, a new program type has been added to implement
infrared decoders. Quote: "The kernel IR decoders support the most
widely used IR protocols, but there are many protocols which are not
supported. [...] There is a 'long tail' of unsupported IR protocols,
for which lircd is need to decode the IR. IR encoding is done in such
a way that some simple circuit can decode it; therefore, BPF is ideal.
[...] user-space can define a decoder in BPF, attach it to the rc
device through the lirc chardev.", from Sean.
4) Several improvements and fixes to BPF core, among others, dumping map
and prog IDs into fdinfo which is a straight forward way to correlate
BPF objects used by applications, removing an indirect call and therefore
retpoline in all map lookup/update/delete calls by invoking the callback
directly for 64 bit archs, adding a new bpf_skb_cgroup_id() BPF helper
for tc BPF programs to have an efficient way of looking up cgroup v2 id
for policy or other use cases. Fixes to make sure we zero tunnel/xfrm
state that hasn't been filled, to allow context access wrt pt_regs in
32 bit archs for tracing, and last but not least various test cases
for fixes that landed in bpf earlier, from Daniel.
5) Get rid of the ndo_xdp_flush API and extend the ndo_xdp_xmit with
a XDP_XMIT_FLUSH flag instead which allows to avoid one indirect
call as flushing is now merged directly into ndo_xdp_xmit(), from Jesper.
6) Add a new bpf_get_current_cgroup_id() helper that can be used in
tracing to retrieve the cgroup id from the current process in order
to allow for e.g. aggregation of container-level events, from Yonghong.
7) Two follow-up fixes for BTF to reject invalid input values and
related to that also two test cases for BPF kselftests, from Martin.
8) Various API improvements to the bpf_fib_lookup() helper, that is,
dropping MPLS bits which are not fully hashed out yet, rejecting
invalid helper flags, returning error for unsupported address
families as well as renaming flowlabel to flowinfo, from David.
9) Various fixes and improvements to sockmap BPF kselftests in particular
in proper error detection and data verification, from Prashant.
10) Two arm32 BPF JIT improvements. One is to fix imm range check with
regards to whether immediate fits into 24 bits, and a naming cleanup
to get functions related to rsh handling consistent to those handling
lsh, from Wang.
11) Two compile warning fixes in BPF, one for BTF and a false positive
to silent gcc in stack_map_get_build_id_offset(), from Arnd.
12) Add missing seg6.h header into tools include infrastructure in order
to fix compilation of BPF kselftests, from Mathieu.
13) Several formatting cleanups in the BPF UAPI helper description that
also fix an error during rst2man compilation, from Quentin.
14) Hide an unused variable in sk_msg_convert_ctx_access() when IPv6 is
not built into the kernel, from Yue.
15) Remove a useless double assignment in dev_map_enqueue(), from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These include a significant update of the generic power domains (genpd)
and Operating Performance Points (OPP) frameworks, mostly related to
the introduction of power domain performance levels, cpufreq updates
(new driver for Qualcomm Kryo processors, updates of the existing
drivers, some core fixes, schedutil governor improvements), PCI power
management fixes, ACPI workaround for EC-based wakeup events handling
on resume from suspend-to-idle, and major updates of the turbostat
and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks
in the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the
schedutil cpufreq governor (Joel Fernandes, Dietmar Eggemann,
Rafael Wysocki, Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman,
Viresh Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag
set and update stale comments in the PCI core PM code (Rafael
Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver
(David Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wqBV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
Drop the in_nmi() check from printk_safe_flush_on_panic()
and attempt to re-init (IOW unlock) locked logbuf spinlock
from panic CPU regardless of its context.
Otherwise, theoretically, we can deadlock on logbuf trying to flush
per-CPU buffers:
a) Panic CPU is running in non-NMI context
b) Panic CPU sends out shutdown IPI via reboot vector
c) Panic CPU fails to stop all remote CPUs
d) Panic CPU sends out shutdown IPI via NMI vector
One of the CPUs that we bring down via NMI vector can hold
logbuf spin lock (theoretically).
Link: http://lkml.kernel.org/r/20180530070350.10131-1-sergey.senozhatsky@gmail.com
To: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Pull timers and timekeeping updates from Thomas Gleixner:
- Core infrastucture work for Y2038 to address the COMPAT interfaces:
+ Add a new Y2038 safe __kernel_timespec and use it in the core
code
+ Introduce config switches which allow to control the various
compat mechanisms
+ Use the new config switch in the posix timer code to control the
32bit compat syscall implementation.
- Prevent bogus selection of CPU local clocksources which causes an
endless reselection loop
- Remove the extra kthread in the clocksource code which has no value
and just adds another level of indirection
- The usual bunch of trivial updates, cleanups and fixlets all over the
place
- More SPDX conversions
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
clocksource/drivers/mxs_timer: Switch to SPDX identifier
clocksource/drivers/timer-imx-tpm: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Remove outdated file path
clocksource/drivers/arc_timer: Add comments about locking while read GFRC
clocksource/drivers/mips-gic-timer: Add pr_fmt and reword pr_* messages
clocksource/drivers/sprd: Fix Kconfig dependency
clocksource: Move inline keyword to the beginning of function declarations
timer_list: Remove unused function pointer typedef
timers: Adjust a kernel-doc comment
tick: Prefer a lower rating device only if it's CPU local device
clocksource: Remove kthread
time: Change nanosleep to safe __kernel_* types
time: Change types to new y2038 safe __kernel_* types
time: Fix get_timespec64() for y2038 safe compat interfaces
time: Add new y2038 safe __kernel_timespec
posix-timers: Make compat syscalls depend on CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_64BIT_TIME in architectures
compat: Enable compat_get/put_timespec64 always
...
Pull irq updates from Thomas Gleixner:
- Consolidation of softirq pending:
The softirq mask and its accessors/mutators have many implementations
scattered around many architectures. Most do the same things
consisting in a field in a per-cpu struct (often irq_cpustat_t)
accessed through per-cpu ops. We can provide instead a generic
efficient version that most of them can use. In fact s390 is the only
exception because the field is stored in lowcore.
- Support for level!?! triggered MSI (ARM)
Over the past couple of years, we've seen some SoCs coming up with
ways of signalling level interrupts using a new flavor of MSIs, where
the MSI controller uses two distinct messages: one that raises a
virtual line, and one that lowers it. The target MSI controller is in
charge of maintaining the state of the line.
This allows for a much simplified HW signal routing (no need to have
hundreds of discrete lines to signal level interrupts if you already
have a memory bus), but results in a departure from the current idea
the kernel has of MSIs.
- Support for Meson-AXG GPIO irqchip
- Large stm32 irqchip rework (suspend/resume, hierarchical domains)
- More SPDX conversions
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
ARM: dts: stm32: Add exti support to stm32mp157 pinctrl
ARM: dts: stm32: Add exti support for stm32mp157c
pinctrl/stm32: Add irq_eoi for stm32gpio irqchip
irqchip/stm32: Add suspend/resume support for hierarchy domain
irqchip/stm32: Add stm32mp1 support with hierarchy domain
irqchip/stm32: Prepare common functions
irqchip/stm32: Add host and driver data structures
irqchip/stm32: Add suspend support
irqchip/stm32: Add falling pending register support
irqchip/stm32: Checkpatch fix
irqchip/stm32: Optimizes and cleans up stm32-exti irq_domain
irqchip/meson-gpio: Add support for Meson-AXG SoCs
dt-bindings: interrupt-controller: New binding for Meson-AXG SoC
dt-bindings: interrupt-controller: Fix the double quotes
softirq/s390: Move default mutators of overwritten softirq mask to s390
softirq/x86: Switch to generic local_softirq_pending() implementation
softirq/sparc: Switch to generic local_softirq_pending() implementation
softirq/powerpc: Switch to generic local_softirq_pending() implementation
softirq/parisc: Switch to generic local_softirq_pending() implementation
softirq/ia64: Switch to generic local_softirq_pending() implementation
...
Pull scheduler updates from Ingo Molnar:
- power-aware scheduling improvements (Patrick Bellasi)
- NUMA balancing improvements (Mel Gorman)
- vCPU scheduling fixes (Rohit Jain)
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Update util_est before updating schedutil
sched/cpufreq: Modify aggregate utilization to always include blocked FAIR utilization
sched/deadline/Documentation: Add overrun signal and GRUB-PA documentation
sched/core: Distinguish between idle_cpu() calls based on desired effect, introduce available_idle_cpu()
sched/wait: Include <linux/wait.h> in <linux/swait.h>
sched/numa: Stagger NUMA balancing scan periods for new threads
sched/core: Don't schedule threads on pre-empted vCPUs
sched/fair: Avoid calling sync_entity_load_avg() unnecessarily
sched/fair: Rearrange select_task_rq_fair() to optimize it
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- x86 Intel uncore driver cleanups and enhancements (Kan Liang)
- group scheduling and other fixes (Song Liu
- store frame pointer in the sample traces for better profiling
(Alexey Budankov)
- compat fixes/enhancements (Eugene Syromiatnikov)
Tooling side changes, which you can build and install in a single step
via:
make -C tools/perf clean install
perf annotate:
- Support 'perf annotate --group' for non-explicit recorded event
"groups", showing multiple columns, one for each event, just like
when dealing with explicit event groups (those enclosed with {})
(Jin Yao)
- Record min/max LBR cycles (>= Skylake) and add 'perf annotate' TUI
hotkey to show it (c) (Jin Yao)
perf bpf:
- Add infrastructure to help in writing eBPF C programs to be used
with '-e name.c' type events in tools such as 'record' and 'trace',
with headers for common constructs and an examples directory that
will get populated as we add more such helpers and the 'perf bpf'
(Arnaldo Carvalho de Melo)
perf stat:
- Display time in precision based on std deviation (Jiri Olsa)
- Add --table option to display time of each run (Jiri Olsa)
- Display length strings of each run for --table option (Jiri Olsa)
perf buildid-cache:
- Add --list and --purge-all options (Ravi Bangoria)
perf test:
- Let 'perf test list' display subtests (Hendrik Brueckner)
perf pti:
- Create extra kernel maps to help in decoding samples in x86 PTI
entry trampolines (Adrian Hunter)
- Copy x86 PTI entry trampoline sections in the kcore copy used for
annotation and intel_pt CPU traces decoding (Adrian Hunter)
... and a lot of other fixes, enhancements and cleanups I did not
list, see the shortlog and git log for details"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
perf/x86/intel/uncore: Clean up client IMC uncore
perf/x86/intel/uncore: Expose uncore_pmu_event*() functions
perf/x86/intel/uncore: Support IIO free-running counters on SKX
perf/x86/intel/uncore: Add infrastructure for free running counters
perf/x86/intel/uncore: Add new data structures for free running counters
perf/x86/intel/uncore: Correct fixed counter index check in generic code
perf/x86/intel/uncore: Correct fixed counter index check for NHM
perf/x86/intel/uncore: Introduce customized event_read() for client IMC uncore
perf/x86: Store user space frame-pointer value on a sample
perf/core: Wire up compat PERF_EVENT_IOC_QUERY_BPF, PERF_EVENT_IOC_MODIFY_ATTRIBUTES
perf/core: Fix bad use of igrab()
perf/core: Fix group scheduling with mixed hw and sw events
perf kcore_copy: Amend the offset of sections that remap kernel text
perf kcore_copy: Copy x86 PTI entry trampoline sections
perf kcore_copy: Get rid of kernel_map
perf kcore_copy: Iterate phdrs
perf kcore_copy: Layout sections
perf kcore_copy: Calculate offset from phnum
perf kcore_copy: Keep a count of phdrs
perf kcore_copy: Keep phdr data in a list
...
Pull locking updates from Ingo Molnar:
- Lots of tidying up changes all across the map for Linux's formal
memory/locking-model tooling, by Alan Stern, Akira Yokosawa, Andrea
Parri, Paul E. McKenney and SeongJae Park.
Notable changes beyond an overall update in the tooling itself is the
tidying up of spin_is_locked() semantics, which spills over into the
kernel proper as well.
- qspinlock improvements: the locking algorithm now guarantees forward
progress whereas the previous implementation in mainline could starve
threads indefinitely in cmpxchg() loops. Also other related cleanups
to the qspinlock code (Will Deacon)
- misc smaller improvements, cleanups and fixes all across the locking
subsystem
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
locking/rwsem: Simplify the is-owner-spinnable checks
tools/memory-model: Add reference for 'Simplifying ARM concurrency'
tools/memory-model: Update ASPLOS information
MAINTAINERS, tools/memory-model: Update e-mail address for Andrea Parri
tools/memory-model: Fix coding style in 'lock.cat'
tools/memory-model: Remove out-of-date comments and code from lock.cat
tools/memory-model: Improve mixed-access checking in lock.cat
tools/memory-model: Improve comments in lock.cat
tools/memory-model: Remove duplicated code from lock.cat
tools/memory-model: Flag "cumulativity" and "propagation" tests
tools/memory-model: Add model support for spin_is_locked()
tools/memory-model: Add scripts to test memory model
tools/memory-model: Fix coding style in 'linux-kernel.def'
tools/memory-model: Model 'smp_store_mb()'
tools/memory-order: Update the cheat-sheet to show that smp_mb__after_atomic() orders later RMW operations
tools/memory-order: Improve key for SELF and SV
tools/memory-model: Fix cheat sheet typo
tools/memory-model: Update required version of herdtools7
tools/memory-model: Redefine rb in terms of rcu-fence
tools/memory-model: Rename link and rcu-path to rcu-link and rb
...
Pull RCU updates from Ingo Molnar:
- updates to the handling of expedited grace periods
- updates to reduce lock contention in the rcu_node combining tree
[ These are in preparation for the consolidation of RCU-bh,
RCU-preempt, and RCU-sched into a single flavor, which was
requested by Linus in response to a security flaw whose root cause
included confusion between the multiple flavors of RCU ]
- torture-test updates that save their users some time and effort
- miscellaneous fixes
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
rcu/x86: Provide early rcu_cpu_starting() callback
torture: Make kvm-find-errors.sh find build warnings
rcutorture: Abbreviate kvm.sh summary lines
rcutorture: Print end-of-test state in kvm.sh summary
rcutorture: Print end-of-test state
torture: Fold parse-torture.sh into parse-console.sh
torture: Add a script to edit output from failed runs
rcu: Update list of rcu_future_grace_period() trace events
rcu: Drop early GP request check from rcu_gp_kthread()
rcu: Simplify and inline cpu_needs_another_gp()
rcu: The rcu_gp_cleanup() function does not need cpu_needs_another_gp()
rcu: Make rcu_start_this_gp() check for out-of-range requests
rcu: Add funnel locking to rcu_start_this_gp()
rcu: Make rcu_start_future_gp() caller select grace period
rcu: Inline rcu_start_gp_advanced() into rcu_start_future_gp()
rcu: Clear request other than RCU_GP_FLAG_INIT at GP end
rcu: Cleanup, don't put ->completed into an int
rcu: Switch __rcu_process_callbacks() to rcu_accelerate_cbs()
rcu: Avoid __call_rcu_core() root rcu_node ->lock acquisition
rcu: Make rcu_migrate_callbacks wake GP kthread when needed
...
Pull siginfo updates from Eric Biederman:
"This set of changes close the known issues with setting si_code to an
invalid value, and with not fully initializing struct siginfo. There
remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64
and x86 to get the code that generates siginfo into a simpler and more
maintainable state. Most of that work involves refactoring the signal
handling code and thus careful code review.
Also not included is the work to shrink the in kernel version of
struct siginfo. That depends on getting the number of places that
directly manipulate struct siginfo under control, as it requires the
introduction of struct kernel_siginfo for the in kernel things.
Overall this set of changes looks like it is making good progress, and
with a little luck I will be wrapping up the siginfo work next
development cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
signal/sh: Stop gcc warning about an impossible case in do_divide_error
signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions
signal/um: More carefully relay signals in relay_signal.
signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR}
signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code
signal/signalfd: Add support for SIGSYS
signal/signalfd: Remove __put_user from signalfd_copyinfo
signal/xtensa: Use force_sig_fault where appropriate
signal/xtensa: Consistenly use SIGBUS in do_unaligned_user
signal/um: Use force_sig_fault where appropriate
signal/sparc: Use force_sig_fault where appropriate
signal/sparc: Use send_sig_fault where appropriate
signal/sh: Use force_sig_fault where appropriate
signal/s390: Use force_sig_fault where appropriate
signal/riscv: Replace do_trap_siginfo with force_sig_fault
signal/riscv: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_mceerr where appropriate
signal/openrisc: Use force_sig_fault where appropriate
signal/nios2: Use force_sig_fault where appropriate
...
An anonymous source sent me a bunch of typo fixes in the comments of
ring_buffer.c file. That source did not want to be associated to this patch
because they don't want to be known as "one of those" commiters (you know who
you are!). They gave me permission to sign this off in my own name.
Suggested-by: One-of-those-commiters@YouKnowWhoYouAre.org
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pull aio updates from Al Viro:
"Majority of AIO stuff this cycle. aio-fsync and aio-poll, mostly.
The only thing I'm holding back for a day or so is Adam's aio ioprio -
his last-minute fixup is trivial (missing stub in !CONFIG_BLOCK case),
but let it sit in -next for decency sake..."
* 'work.aio-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
aio: sanitize the limit checking in io_submit(2)
aio: fold do_io_submit() into callers
aio: shift copyin of iocb into io_submit_one()
aio_read_events_ring(): make a bit more readable
aio: all callers of aio_{read,write,fsync,poll} treat 0 and -EIOCBQUEUED the same way
aio: take list removal to (some) callers of aio_complete()
aio: add missing break for the IOCB_CMD_FDSYNC case
random: convert to ->poll_mask
timerfd: convert to ->poll_mask
eventfd: switch to ->poll_mask
pipe: convert to ->poll_mask
crypto: af_alg: convert to ->poll_mask
net/rxrpc: convert to ->poll_mask
net/iucv: convert to ->poll_mask
net/phonet: convert to ->poll_mask
net/nfc: convert to ->poll_mask
net/caif: convert to ->poll_mask
net/bluetooth: convert to ->poll_mask
net/sctp: convert to ->poll_mask
net/tipc: convert to ->poll_mask
...
Commit bf6fa2c893 ("bpf: implement bpf_get_current_cgroup_id()
helper") introduced a new helper bpf_get_current_cgroup_id().
The helper has a dependency on CONFIG_CGROUPS.
When CONFIG_CGROUPS is not defined, using the helper will result
the following verifier error:
kernel subsystem misconfigured func bpf_get_current_cgroup_id#80
which is hard for users to interpret.
Guarding the reference to bpf_get_current_cgroup_id_proto with
CONFIG_CGROUPS will result in below better message:
unknown func bpf_get_current_cgroup_id#80
Fixes: bf6fa2c893 ("bpf: implement bpf_get_current_cgroup_id() helper")
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
* pm-pci:
PCI / PM: Clean up outdated comments in pci_target_state()
PCI / PM: Do not clear state_saved for devices that remain suspended
* acpi-pm:
ACPI: EC: Dispatch the EC GPE directly on s2idle wake
ACPICA: Introduce acpi_dispatch_gpe()
* pm-sleep:
PM / hibernate: Fix oops at snapshot_write()
PM / wakeup: Make s2idle_lock a RAW_SPINLOCK
PM / s2idle: Make s2idle_wait_head swait based
PM / wakeup: Make events_lock a RAW_SPINLOCK
PM / suspend: Prevent might sleep splats
* pm-avs:
PM / AVS: rockchip-io: add io selectors and supplies for PX30
* pm-qos:
PM / QoS: Drop redundant declaration of pm_qos_get_value()
* pm-core:
PM / runtime: Drop usage count for suppliers at device link removal
PM / runtime: Fixup reference counting of device link suppliers at probe
PM: wakeup: Use pr_debug() for the "aborting suspend" message
PM / core: Drop unused internal inline functions for sysfs
PM / core: Drop unused internal functions for pm_qos sysfs
PM / core: Drop unused internal inline functions for wakeirqs
PM / core: Drop internal unused inline functions for wakeups
PM / wakeup: Only update last time for active wakeup sources
PM / wakeup: Use seq_open() to show wakeup stats
PM / core: Use dev_printk() and symbols in suspend/resume diagnostics
PM / core: Simplify initcall_debug_report() timing
PM / core: Remove unused initcall_debug_report() arguments
PM / core: fix deferred probe breaking suspend resume order
bpf has been used extensively for tracing. For example, bcc
contains an almost full set of bpf-based tools to trace kernel
and user functions/events. Most tracing tools are currently
either filtered based on pid or system-wide.
Containers have been used quite extensively in industry and
cgroup is often used together to provide resource isolation
and protection. Several processes may run inside the same
container. It is often desirable to get container-level tracing
results as well, e.g. syscall count, function count, I/O
activity, etc.
This patch implements a new helper, bpf_get_current_cgroup_id(),
which will return cgroup id based on the cgroup within which
the current task is running.
The later patch will provide an example to show that
userspace can get the same cgroup id so it could
configure a filter or policy in the bpf program based on
task cgroup id.
The helper is currently implemented for tracing. It can
be added to other program types as well when needed.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull scheduler fixes from Thomas Gleixner:
- two patches addressing the problem that the scheduler allows under
certain conditions user space tasks to be scheduled on CPUs which are
not yet fully booted which causes a few subtle and hard to debug
issue
- add a missing runqueue clock update in the deadline scheduler which
triggers a warning under certain circumstances
- fix a silly typo in the scheduler header file
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/headers: Fix typo
sched/deadline: Fix missing clock update
sched/core: Require cpu_active() in select_task_rq(), for user tasks
sched/core: Fix rules for running on online && !active CPUs
The XDP_REDIRECT map devmap can avoid using ndo_xdp_flush, by instead
instructing ndo_xdp_xmit to flush via XDP_XMIT_FLUSH flag in
appropriate places.
Notice after this patch it is possible to remove ndo_xdp_flush
completely, as this is the last user of ndo_xdp_flush. This is left
for later patches, to keep driver changes separate.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch only change the API and reject any use of flags. This is an
intermediate step that allows us to implement the flush flag operation
later, for each individual driver in a separate patch.
The plan is to implement flush operation via XDP_XMIT_FLUSH flag
and then remove XDP_XMIT_FLAGS_NONE when done.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Wang reported that all the testcases for BPF_PROG_TYPE_PERF_EVENT
program type in test_verifier report the following errors on x86_32:
172/p unpriv: spill/fill of different pointers ldx FAIL
Unexpected error message!
0: (bf) r6 = r10
1: (07) r6 += -8
2: (15) if r1 == 0x0 goto pc+3
R1=ctx(id=0,off=0,imm=0) R6=fp-8,call_-1 R10=fp0,call_-1
3: (bf) r2 = r10
4: (07) r2 += -76
5: (7b) *(u64 *)(r6 +0) = r2
6: (55) if r1 != 0x0 goto pc+1
R1=ctx(id=0,off=0,imm=0) R2=fp-76,call_-1 R6=fp-8,call_-1 R10=fp0,call_-1 fp-8=fp
7: (7b) *(u64 *)(r6 +0) = r1
8: (79) r1 = *(u64 *)(r6 +0)
9: (79) r1 = *(u64 *)(r1 +68)
invalid bpf_context access off=68 size=8
378/p check bpf_perf_event_data->sample_period byte load permitted FAIL
Failed to load prog 'Permission denied'!
0: (b7) r0 = 0
1: (71) r0 = *(u8 *)(r1 +68)
invalid bpf_context access off=68 size=1
379/p check bpf_perf_event_data->sample_period half load permitted FAIL
Failed to load prog 'Permission denied'!
0: (b7) r0 = 0
1: (69) r0 = *(u16 *)(r1 +68)
invalid bpf_context access off=68 size=2
380/p check bpf_perf_event_data->sample_period word load permitted FAIL
Failed to load prog 'Permission denied'!
0: (b7) r0 = 0
1: (61) r0 = *(u32 *)(r1 +68)
invalid bpf_context access off=68 size=4
381/p check bpf_perf_event_data->sample_period dword load permitted FAIL
Failed to load prog 'Permission denied'!
0: (b7) r0 = 0
1: (79) r0 = *(u64 *)(r1 +68)
invalid bpf_context access off=68 size=8
Reason is that struct pt_regs on x86_32 doesn't fully align to 8 byte
boundary due to its size of 68 bytes. Therefore, bpf_ctx_narrow_access_ok()
will then bail out saying that off & (size_default - 1) which is 68 & 7
doesn't cleanly align in the case of sample_period access from struct
bpf_perf_event_data, hence verifier wrongly thinks we might be doing an
unaligned access here though underlying arch can handle it just fine.
Therefore adjust this down to machine size and check and rewrite the
offset for narrow access on that basis. We also need to fix corresponding
pe_prog_is_valid_access(), since we hit the check for off % size != 0
(e.g. 68 % 8 -> 4) in the first and last test. With that in place, progs
for tracing work on x86_32.
Reported-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
While some of the BPF map lookup helpers provide a ->map_gen_lookup()
callback for inlining the map lookup altogether it is not available
for every map, so the remaining ones have to call bpf_map_lookup_elem()
helper which does a dispatch to map->ops->map_lookup_elem(). In
times of retpolines, this will control and trap speculative execution
rather than letting it do its work for the indirect call and will
therefore cause a slowdown. Likewise, bpf_map_update_elem() and
bpf_map_delete_elem() do not have an inlined version and need to call
into their map->ops->map_update_elem() resp. map->ops->map_delete_elem()
handlers.
Before:
# bpftool prog dump xlated id 1
0: (bf) r2 = r10
1: (07) r2 += -8
2: (7a) *(u64 *)(r2 +0) = 0
3: (18) r1 = map[id:1]
5: (85) call __htab_map_lookup_elem#232656
6: (15) if r0 == 0x0 goto pc+4
7: (71) r1 = *(u8 *)(r0 +35)
8: (55) if r1 != 0x0 goto pc+1
9: (72) *(u8 *)(r0 +35) = 1
10: (07) r0 += 56
11: (15) if r0 == 0x0 goto pc+4
12: (bf) r2 = r0
13: (18) r1 = map[id:1]
15: (85) call bpf_map_delete_elem#215008 <-- indirect call via
16: (95) exit helper
After:
# bpftool prog dump xlated id 1
0: (bf) r2 = r10
1: (07) r2 += -8
2: (7a) *(u64 *)(r2 +0) = 0
3: (18) r1 = map[id:1]
5: (85) call __htab_map_lookup_elem#233328
6: (15) if r0 == 0x0 goto pc+4
7: (71) r1 = *(u8 *)(r0 +35)
8: (55) if r1 != 0x0 goto pc+1
9: (72) *(u8 *)(r0 +35) = 1
10: (07) r0 += 56
11: (15) if r0 == 0x0 goto pc+4
12: (bf) r2 = r0
13: (18) r1 = map[id:1]
15: (85) call htab_lru_map_delete_elem#238240 <-- direct call
16: (95) exit
In all three lookup/update/delete cases however we can use the actual
address of the map callback directly if we find that there's only a
single path with a map pointer leading to the helper call, meaning
when the map pointer has not been poisoned from verifier side.
Example code can be seen above for the delete case.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Its trivial and straight forward to expose it for scripts that can
then use it along with bpftool in order to inspect an individual
application's used maps and progs. Right now we dump some basic
information in the fdinfo file but with the help of the map/prog
id full introspection becomes possible now.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stating 'proprietary program' in the error is just silly since it
can also be a different open source license than that which is just
not compatible.
Reference: https://twitter.com/majek04/status/998531268039102465
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently a mismatch between the resources that will trigger
the e820_pmem driver to register/load and the resources that will
actually be surfaced as pmem ranges. register_e820_pmem() uses
walk_iomem_res_desc() which includes children and siblings. In contrast,
e820_pmem_probe() only considers top level resources. For example the
following resource tree results in the driver being loaded, but no
resources being registered:
398000000000-39bfffffffff : PCI Bus 0000:ae
39be00000000-39bf07ffffff : PCI Bus 0000:af
39be00000000-39beffffffff : 0000:af:00.0
39be10000000-39beffffffff : Persistent Memory (legacy)
Fix this up to allow definitions of "legacy" pmem ranges anywhere in
system-physical address space. Not that it is a recommended or safe to
define a pmem range in PCI space, but it is useful for debug /
experimentation, and the restriction on being a top-level resource was
arbitrary.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The t->type in BTF_KIND_FWD is not used. It must be 0.
This patch ensures that and also adds a test case in test_btf.c
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch ensures array's t->size is 0.
The array size is decided by its individual elem's size and the
number of elements. Hence, t->size is not used and
it must be 0.
A test case is added to test_btf.c
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A missing clock update is causing the following warning:
rq->clock_update_flags < RQCF_ACT_SKIP
WARNING: CPU: 10 PID: 0 at kernel/sched/sched.h:963 inactive_task_timer+0x5d6/0x720
Call Trace:
<IRQ>
__hrtimer_run_queues+0x10f/0x530
hrtimer_interrupt+0xe5/0x240
smp_apic_timer_interrupt+0x79/0x2b0
apic_timer_interrupt+0xf/0x20
</IRQ>
do_idle+0x203/0x280
cpu_startup_entry+0x6f/0x80
start_secondary+0x1b0/0x200
secondary_startup_64+0xa5/0xb0
hardirqs last enabled at (793919): [<ffffffffa27c5f6e>] cpuidle_enter_state+0x9e/0x360
hardirqs last disabled at (793920): [<ffffffffa2a0096e>] interrupt_entry+0xce/0xe0
softirqs last enabled at (793922): [<ffffffffa20bef78>] irq_enter+0x68/0x70
softirqs last disabled at (793921): [<ffffffffa20bef5d>] irq_enter+0x4d/0x70
This happens because inactive_task_timer() calls sub_running_bw() (if
TASK_DEAD and non_contending) that might trigger a schedutil update,
which might access the clock. Clock is however currently updated only
later in inactive_task_timer() function.
Fix the problem by updating the clock right after task_rq_lock().
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Claudio Scordino <claudio@evidence.eu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luca Abeni <luca.abeni@santannapisa.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180530160809.9074-1-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
select_task_rq() is used in a few paths to select the CPU upon which a
thread should be run - for example it is used by try_to_wake_up() & by
fork or exec balancing. As-is it allows use of any online CPU that is
present in the task's cpus_allowed mask.
This presents a problem because there is a period whilst CPUs are
brought online where a CPU is marked online, but is not yet fully
initialized - ie. the period where CPUHP_AP_ONLINE_IDLE <= state <
CPUHP_ONLINE. Usually we don't run any user tasks during this window,
but there are corner cases where this can happen. An example observed
is:
- Some user task A, running on CPU X, forks to create task B.
- sched_fork() calls __set_task_cpu() with cpu=X, setting task B's
task_struct::cpu field to X.
- CPU X is offlined.
- Task A, currently somewhere between the __set_task_cpu() in
copy_process() and the call to wake_up_new_task(), is migrated to
CPU Y by migrate_tasks() when CPU X is offlined.
- CPU X is onlined, but still in the CPUHP_AP_ONLINE_IDLE state. The
scheduler is now active on CPU X, but there are no user tasks on
the runqueue.
- Task A runs on CPU Y & reaches wake_up_new_task(). This calls
select_task_rq() with cpu=X, taken from task B's task_struct,
and select_task_rq() allows CPU X to be returned.
- Task A enqueues task B on CPU X's runqueue, via activate_task() &
enqueue_task().
- CPU X now has a user task on its runqueue before it has reached the
CPUHP_ONLINE state.
In most cases, the user tasks that schedule on the newly onlined CPU
have no idea that anything went wrong, but one case observed to be
problematic is if the task goes on to invoke the sched_setaffinity
syscall. The newly onlined CPU reaches the CPUHP_AP_ONLINE_IDLE state
before the CPU that brought it online calls stop_machine_unpark(). This
means that for a portion of the window of time between
CPUHP_AP_ONLINE_IDLE & CPUHP_ONLINE the newly onlined CPU's struct
cpu_stopper has its enabled field set to false. If a user thread is
executed on the CPU during this window and it invokes sched_setaffinity
with a CPU mask that does not include the CPU it's running on, then when
__set_cpus_allowed_ptr() calls stop_one_cpu() intending to invoke
migration_cpu_stop() and perform the actual migration away from the CPU
it will simply return -ENOENT rather than calling migration_cpu_stop().
We then return from the sched_setaffinity syscall back to the user task
that is now running on a CPU which it just asked not to run on, and
which is not present in its cpus_allowed mask.
This patch resolves the problem by having select_task_rq() enforce that
user tasks run on CPUs that are active - the same requirement that
select_fallback_rq() already enforces. This should ensure that newly
onlined CPUs reach the CPUHP_AP_ACTIVE state before being able to
schedule user tasks, and also implies that bringup_wait_for_ap() will
have called stop_machine_unpark() which resolves the sched_setaffinity
issue above.
I haven't yet investigated them, but it may be of interest to review
whether any of the actions performed by hotplug states between
CPUHP_AP_ONLINE_IDLE & CPUHP_AP_ACTIVE could have similar unintended
effects on user tasks that might schedule before they are reached, which
might widen the scope of the problem from just affecting the behaviour
of sched_setaffinity.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180526154648.11635-2-paul.burton@mips.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As already enforced by the WARN() in __set_cpus_allowed_ptr(), the rules
for running on an online && !active CPU are stricter than just being a
kthread, you need to be a per-cpu kthread.
If you're not strictly per-CPU, you have better CPUs to run on and
don't need the partially booted one to get your work done.
The exception is to allow smpboot threads to bootstrap the CPU itself
and get kernel 'services' initialized before we allow userspace on it.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 955dbdf4ce ("sched: Allow migrating kthreads into online but inactive CPUs")
Link: http://lkml.kernel.org/r/20170725165821.cejhb7v2s3kecems@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The assignment dev = dev is redundant and should be removed.
Detected by CoverityScan, CID#1469486 ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add support for BPF_PROG_LIRC_MODE2. This type of BPF program can call
rc_keydown() to reported decoded IR scancodes, or rc_repeat() to report
that the last key should be repeated.
The bpf program can be attached to using the bpf(BPF_PROG_ATTACH) syscall;
the target_fd must be the /dev/lircN device.
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This makes is it possible for bpf prog detach to return -ENOENT.
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull RCU fix from Paul E. McKenney:
"This additional v4.18 pull request contains a single commit that fell
through the cracks:
Provide early rcu_cpu_starting() callback for the benefit of the
x86/mtrr code, which needs RCU to be available on incoming CPUs
earlier than has been the case in the past."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that trace_marker can have triggers, including a histogram triggers, the
onmatch() and onmax() access the trace event. To do so, the search routine
to find the event file needs to use the raw __find_event_file() that does
not filter out ftrace events.
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
As strings in trace events may not have a nul terminating character, the
filter string compares use the defined string length for the field for the
compares.
The trace_marker records data slightly different than do normal events. It's
size is zero, meaning that the string is the rest of the array, and that the
string also ends with '\0'.
If the size is zero, assume that the string is nul terminated and read the
string in question as is.
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Allow writing to the trace_markers file initiate triggers defined in
tracefs/ftrace/print/trigger file. This will allow of user space to trigger
the same type of triggers (including histograms) that the trace events use.
Had to create a ftrace_event_register() function that will become the
trace_marker print event's reg() function. This is required because of how
triggers are enabled:
event_trigger_write() {
event_trigger_regex_write() {
trigger_process_regex() {
for p in trigger_commands {
p->func(); /* trigger_snapshot_cmd->func */
event_trigger_callback() {
cmd_ops->reg() /* register_trigger() */ {
trace_event_trigger_enable_disable() {
trace_event_enable_disable() {
call->class->reg();
Without the reg() function, the trigger code will call a NULL pointer and
crash the system.
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Clark Williams <williams@redhat.com>
Cc: Karim Yaghmour <karim.yaghmour@opersys.com>
Cc: Brendan Gregg <bgregg@netflix.com>
Suggested-by: Joel Fernandes <joelaf@google.com>
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
bugs that deal with triggers and instances.
The first is a generic trigger bug where the triggers are not removed
from a link list properly when deleting an instance.
The second is specific to snapshots, where the snapshot is does the
snapshot to the top level buffer, when it is suppose to snapshot the
buffer associated to the instance the snapshot trigger exists in.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCWw0+4hQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qpwyAQC56/yYzfpJnpjwcI2E7j8FihLg0Nlr
bq85CcQGRm07dwD+L90disWyPxpxH/fGO4OCET1LeoaO1I/fBfECR2XXjQY=
=w4al
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.17-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"While writing selftests for a new feature, I triggered two existing
bugs that deal with triggers and instances.
- a generic trigger bug where the triggers are not removed from a
linked list properly when deleting an instance.
- a bug specific to snapshots, where the snapshot is done in the top
level buffer, when it is supposed to snapshot the buffer associated
to the instance the snapshot trigger exists in"
* tag 'trace-v4.17-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Make the snapshot trigger work with instances
tracing: Fix crash when freeing instances with event triggers
The filter file in the ftrace internal events, like in
/sys/kernel/tracing/events/ftrace/function/filter is not attached to any
functionality. Do not create them as they are meaningless.
In the future, if an ftrace internal event gets filter functionality, then
it will need to create it directly.
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The dynamic arrays defined for ftrace internal events, such as the buf field
for trace_marker (ftrace/print) did not have brackets which makes the filter
code not accept it as a string. This is not currently an issues because the
filter code doesn't do anything for these events, but they will in the
future, and this needs to be fixed for when it does.
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Instead of having both trace_init_tracefs() and event_trace_init() be called
by fs_initcall() routines, have event_trace_init() called directly by
trace_init_tracefs(). This will guarantee order of how the events are
created with respect to the rest of the ftrace infrastructure. This is
needed to be able to assoctiate event files with ftrace internal events,
such as the trace_marker.
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
By adding the function __find_event_file() that can search for files without
restrictions, such as if the event associated with the file has a reg
function, or if it has the "ignore" flag set, the files that are associated
to ftrace internal events (like trace_marker and function events) can be
found and used.
find_event_file() still returns a "filtered" file, as most callers need a
valid trace event file. One created by the trace_events.h macros and not one
created for parsing ftrace specific events.
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Trace event triggers can be called before or after the event has been
committed. If it has been called after the commit, there's a possibility
that the event no longer exists. Currently, the two post callers is the
trigger to disable tracing (traceoff) and the one that will record a stack
dump (stacktrace). Neither of them reference the trace event entry record,
as that would lead to a race condition that could pass in corrupted data.
To prevent any other users of the post data triggers from using the trace
event record, pass in NULL to the post call trigger functions for the event
record, as they should never need to use them in the first place.
This does not fix any bug, but prevents bugs from happening by new post call
trigger users.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The description of tracepoint_probe_register duplicates
with tracepoint_probe_register_prio. This patch cleans up
the descriptions.
Link: http://lkml.kernel.org/r/20170616082643.7311-1-jlee@suse.com
Signed-off-by: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The snapshot trigger currently only affects the main ring buffer, even when
it is used by the instances. This can be confusing as the snapshot trigger
is listed in the instance.
> # cd /sys/kernel/tracing
> # mkdir instances/foo
> # echo snapshot > instances/foo/events/syscalls/sys_enter_fchownat/trigger
> # echo top buffer > trace_marker
> # echo foo buffer > instances/foo/trace_marker
> # touch /tmp/bar
> # chown rostedt /tmp/bar
> # cat instances/foo/snapshot
# tracer: nop
#
#
# * Snapshot is freed *
#
# Snapshot commands:
# echo 0 > snapshot : Clears and frees snapshot buffer
# echo 1 > snapshot : Allocates snapshot buffer, if not already allocated.
# Takes a snapshot of the main buffer.
# echo 2 > snapshot : Clears snapshot buffer (but does not allocate or free)
# (Doesn't have to be '2' works with any number that
# is not a '0' or '1')
> # cat snapshot
# tracer: nop
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / delay
# TASK-PID CPU# |||| TIMESTAMP FUNCTION
# | | | |||| | |
bash-1189 [000] .... 111.488323: tracing_mark_write: top buffer
Not only did the snapshot occur in the top level buffer, but the instance
snapshot buffer should have been allocated, and it is still free.
Cc: stable@vger.kernel.org
Fixes: 85f2b08268 ("tracing: Add basic event trigger framework")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
In addition to already existing BPF hooks for sys_bind and sys_connect,
the patch provides new hooks for sys_sendmsg.
It leverages existing BPF program type `BPF_PROG_TYPE_CGROUP_SOCK_ADDR`
that provides access to socket itlself (properties like family, type,
protocol) and user-passed `struct sockaddr *` so that BPF program can
override destination IP and port for system calls such as sendto(2) or
sendmsg(2) and/or assign source IP to the socket.
The hooks are implemented as two new attach types:
`BPF_CGROUP_UDP4_SENDMSG` and `BPF_CGROUP_UDP6_SENDMSG` for UDPv4 and
UDPv6 correspondingly.
UDPv4 and UDPv6 separate attach types for same reason as sys_bind and
sys_connect hooks, i.e. to prevent reading from / writing to e.g.
user_ip6 fields when user passes sockaddr_in since it'd be out-of-bound.
The difference with already existing hooks is sys_sendmsg are
implemented only for unconnected UDP.
For TCP it doesn't make sense to change user-provided `struct sockaddr *`
at sendto(2)/sendmsg(2) time since socket either was already connected
and has source/destination set or wasn't connected and call to
sendto(2)/sendmsg(2) would lead to ENOTCONN anyway.
Connected UDP is already handled by sys_connect hooks that can override
source/destination at connect time and use fast-path later, i.e. these
hooks don't affect UDP fast-path.
Rewriting source IP is implemented differently than that in sys_connect
hooks. When sys_sendmsg is used with unconnected UDP it doesn't work to
just bind socket to desired local IP address since source IP can be set
on per-packet basis by using ancillary data (cmsg(3)). So no matter if
socket is bound or not, source IP has to be rewritten on every call to
sys_sendmsg.
To do so two new fields are added to UAPI `struct bpf_sock_addr`;
* `msg_src_ip4` to set source IPv4 for UDPv4;
* `msg_src_ip6` to set source IPv6 for UDPv6.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The stack_map_get_build_id_offset() function is too long for gcc to track
whether 'work' may or may not be initialized at the end of it, leading
to a false-positive warning:
kernel/bpf/stackmap.c: In function 'stack_map_get_build_id_offset':
kernel/bpf/stackmap.c:334:13: error: 'work' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This removes the 'in_nmi_ctx' flag and uses the state of that variable
itself to see if it got initialized.
Fixes: bae77c5eb5 ("bpf: enable stackmap with build_id in nmi context")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
gcc warns about a noreturn function possibly returning in
some configurations:
kernel/bpf/btf.c: In function 'env_type_is_resolve_sink':
kernel/bpf/btf.c:729:1: error: control reaches end of non-void function [-Werror=return-type]
Using BUG() instead of BUG_ON() avoids that warning and otherwise
does the exact same thing.
Fixes: eb3f595dab ("bpf: btf: Validate type reference")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If a instance has an event trigger enabled when it is freed, it could cause
an access of free memory. Here's the case that crashes:
# cd /sys/kernel/tracing
# mkdir instances/foo
# echo snapshot > instances/foo/events/initcall/initcall_start/trigger
# rmdir instances/foo
Would produce:
general protection fault: 0000 [#1] PREEMPT SMP PTI
Modules linked in: tun bridge ...
CPU: 5 PID: 6203 Comm: rmdir Tainted: G W 4.17.0-rc4-test+ #933
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03 07/14/2016
RIP: 0010:clear_event_triggers+0x3b/0x70
RSP: 0018:ffffc90003783de0 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 6b6b6b6b6b6b6b2b RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8800c7130ba0
RBP: ffffc90003783e00 R08: ffff8801131993f8 R09: 0000000100230016
R10: ffffc90003783d80 R11: 0000000000000000 R12: ffff8800c7130ba0
R13: ffff8800c7130bd8 R14: ffff8800cc093768 R15: 00000000ffffff9c
FS: 00007f6f4aa86700(0000) GS:ffff88011eb40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f6f4a5aed60 CR3: 00000000cd552001 CR4: 00000000001606e0
Call Trace:
event_trace_del_tracer+0x2a/0xc5
instance_rmdir+0x15c/0x200
tracefs_syscall_rmdir+0x52/0x90
vfs_rmdir+0xdb/0x160
do_rmdir+0x16d/0x1c0
__x64_sys_rmdir+0x17/0x20
do_syscall_64+0x55/0x1a0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
This was due to the call the clears out the triggers when an instance is
being deleted not removing the trigger from the link list.
Cc: stable@vger.kernel.org
Fixes: 85f2b08268 ("tracing: Add basic event trigger framework")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
syzbot is reporting NULL pointer dereference at snapshot_write() [1].
This is because data->handle is zero-cleared by ioctl(SNAPSHOT_FREE).
Fix this by checking data_of(data->handle) != NULL before using it.
[1] https://syzkaller.appspot.com/bug?id=828a3c71bd344a6de8b6a31233d51a72099f27fd
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+ae590932da6e45d6564d@syzkaller.appspotmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The `s2idle_lock' is acquired during suspend while interrupts are
disabled even on RT. The lock is acquired for short sections only.
Make it a RAW lock which avoids "sleeping while atomic" warnings on RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
s2idle_wait_head is used during s2idle with interrupts disabled even on
RT. There is no "custom" wake up function so swait could be used instead
which is also lower weight compared to the wait_queue.
Make s2idle_wait_head a swait_queue_head.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
timekeeping suspend/resume calls read_persistent_clock() which takes
rtc_lock. That results in might sleep warnings because at that point
we run with interrupts disabled.
We cannot convert rtc_lock to a raw spinlock as that would trigger
other might sleep warnings.
As a workaround we disable the might sleep warnings by setting
system_state to SYSTEM_SUSPEND before calling sysdev_suspend() and
restoring it to SYSTEM_RUNNING afer sysdev_resume(). There is no lock
contention because hibernate / suspend to RAM is single-CPU at this
point.
In s2idle's case the system_state is set to SYSTEM_SUSPEND before
timekeeping_suspend() which is invoked by the last CPU. In the resume
case it set back to SYSTEM_RUNNING after timekeeping_resume() which is
invoked by the first CPU in the resume case. The other CPUs will block
on tick_freeze_lock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: cover s2idle in tick_freeze() / tick_unfreeze()]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull scheduler fixes from Thomas Gleixner:
"Three fixes for scheduler and kthread code:
- allow calling kthread_park() on an already parked thread
- restore the sched_pi_setprio() tracepoint behaviour
- clarify the unclear string for the scheduling domain debug output"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched, tracing: Fix trace_sched_pi_setprio() for deboosting
kthread: Allow kthread_park() on a parked kthread
sched/topology: Clarify root domain(s) debug string
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
kasan: fix memory hotplug during boot
kasan: free allocated shadow memory on MEM_CANCEL_ONLINE
checkpatch: fix macro argument precedence test
init/main.c: include <linux/mem_encrypt.h>
kernel/sys.c: fix potential Spectre v1 issue
mm/memory_hotplug: fix leftover use of struct page during hotplug
proc: fix smaps and meminfo alignment
mm: do not warn on offline nodes unless the specific node is explicitly requested
mm, memory_hotplug: make has_unmovable_pages more robust
mm/kasan: don't vfree() nonexistent vm_area
MAINTAINERS: change hugetlbfs maintainer and update files
ipc/shm: fix shmat() nil address after round-down when remapping
Revert "ipc/shm: Fix shmat mmap nil-page protection"
idr: fix invalid ptr dereference on item delete
ocfs2: revert "ocfs2/o2hb: check len for bio_add_page() to avoid getting incorrect bio"
mm: fix nr_rotate_swap leak in swapon() error case
Pull networking fixes from David Miller:
"Let's begin the holiday weekend with some networking fixes:
1) Whoops need to restrict cfg80211 wiphy names even more to 64
bytes. From Eric Biggers.
2) Fix flags being ignored when using kernel_connect() with SCTP,
from Xin Long.
3) Use after free in DCCP, from Alexey Kodanev.
4) Need to check rhltable_init() return value in ipmr code, from Eric
Dumazet.
5) XDP handling fixes in virtio_net from Jason Wang.
6) Missing RTA_TABLE in rtm_ipv4_policy[], from Roopa Prabhu.
7) Need to use IRQ disabling spinlocks in mlx4_qp_lookup(), from Jack
Morgenstein.
8) Prevent out-of-bounds speculation using indexes in BPF, from
Daniel Borkmann.
9) Fix regression added by AF_PACKET link layer cure, from Willem de
Bruijn.
10) Correct ENIC dma mask, from Govindarajulu Varadarajan.
11) Missing config options for PMTU tests, from Stefano Brivio"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (48 commits)
ibmvnic: Fix partial success login retries
selftests/net: Add missing config options for PMTU tests
mlx4_core: allocate ICM memory in page size chunks
enic: set DMA mask to 47 bit
ppp: remove the PPPIOCDETACH ioctl
ipv4: remove warning in ip_recv_error
net : sched: cls_api: deal with egdev path only if needed
vhost: synchronize IOTLB message with dev cleanup
packet: fix reserve calculation
net/mlx5: IPSec, Fix a race between concurrent sandbox QP commands
net/mlx5e: When RXFCS is set, add FCS data into checksum calculation
bpf: properly enforce index mask to prevent out-of-bounds speculation
net/mlx4: Fix irq-unsafe spinlock usage
net: phy: broadcom: Fix bcm_write_exp()
net: phy: broadcom: Fix auxiliary control register reads
net: ipv4: add missing RTA_TABLE to rtm_ipv4_policy
net/mlx4: fix spelling mistake: "Inrerface" -> "Interface" and rephrase message
ibmvnic: Only do H_EOI for mobility events
tuntap: correctly set SOCKWQ_ASYNC_NOSPACE
virtio-net: fix leaking page for gso packet during mergeable XDP
...
`resource' can be controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
kernel/sys.c:1474 __do_compat_sys_old_getrlimit() warn: potential spectre issue 'get_current()->signal->rlim' (local cap)
kernel/sys.c:1455 __do_sys_old_getrlimit() warn: potential spectre issue 'get_current()->signal->rlim' (local cap)
Fix this by sanitizing *resource* before using it to index
current->signal->rlim
Notice that given that speculation windows are large, the policy is to
kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Link: http://lkml.kernel.org/r/20180515030038.GA11822@embeddedor.com
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Borkmann says:
====================
pull-request: bpf 2018-05-24
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in the original fix to prevent out of bounds speculation when
multiple tail call maps from different branches or calls end up at the
same tail call helper invocation, from Daniel.
2) Two selftest fixes, one in reuseport_bpf_numa where test is skipped in
case of missing numa support and another one to update kernel config to
properly support xdp_meta.sh test, from Anders.
...
Would be great if you have a chance to merge net into net-next after that.
The verifier fix would be needed later as a dependency in bpf-next for
upcomig work there. When you do the merge there's a trivial conflict on
BPF side with 849fa50662 ("bpf/verifier: refine retval R0 state for
bpf_get_stack helper"): Resolution is to keep both functions, the
do_refine_retval_range() and record_func_map().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trivial owner_on_cpu() helper for rwsem_can_spin_on_owner() and
rwsem_spin_on_owner(), it also allows to make rwsem_can_spin_on_owner()
a bit more clear.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Waiman Long <longman@redhat.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jan Kara <jack@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Theodore Y. Ts'o <tytso@mit.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180518165534.GA22348@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since pointer size is different in compat, and switching in _perf_ioctl
is done using exact ioctl numbers, all new ioctl numbers that use pointer
should be added to perf_compat_ioctl for _IOC_SIZE fixup before passing
to perf_ioctl routine (this shouldn't be needed if semantics of the size
argument of _IO* macros was honored).
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20180521123420.GA24291@asgard.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As Miklos reported and suggested:
"This pattern repeats two times in trace_uprobe.c and in
kernel/events/core.c as well:
ret = kern_path(filename, LOOKUP_FOLLOW, &path);
if (ret)
goto fail_address_parse;
inode = igrab(d_inode(path.dentry));
path_put(&path);
And it's wrong. You can only hold a reference to the inode if you
have an active ref to the superblock as well (which is normally
through path.mnt) or holding s_umount.
This way unmounting the containing filesystem while the tracepoint is
active will give you the "VFS: Busy inodes after unmount..." message
and a crash when the inode is finally put.
Solution: store path instead of inode."
This patch fixes the issue in kernel/event/core.c.
Reviewed-and-tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reported-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <kernel-team@fb.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 375637bc52 ("perf/core: Introduce address range filtering")
Link: http://lkml.kernel.org/r/20180418062907.3210386-2-songliubraving@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When hw and sw events are mixed in the same group, they are all attached
to the hw perf_event_context. This sometimes requires moving group of
perf_event to a different context.
We found a bug in how the kernel handles this, for example if we do:
perf stat -e '{faults,ref-cycles,faults}' -I 1000
1.005591180 1,297 faults
1.005591180 457,476,576 ref-cycles
1.005591180 <not supported> faults
First, sw event "faults" is attached to the sw context, and becomes the
group leader. Then, hw event "ref-cycles" is attached, so both events
are moved to the hw context. Last, another sw "faults" tries to attach,
but it fails because of mismatch between the new target ctx (from sw
pmu) and the group_leader's ctx (hw context, same as ref-cycles).
The broken condition is:
group_leader is sw event;
group_leader is on hw context;
add a sw event to the group.
Fix this scenario by checking group_leader's context (instead of just
event type). If group_leader is on hw context, use the ->pmu of this
context to look up context for the new event.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <kernel-team@fb.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: b04243ef70 ("perf: Complete software pmu grouping")
Link: http://lkml.kernel.org/r/20180503194716.162815-1-songliubraving@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When a task is enqueued the estimated utilization of a CPU is updated
to better support the selection of the required frequency.
However, schedutil is (implicitly) updated by update_load_avg() which
always happens before util_est_{en,de}queue(), thus potentially
introducing a latency between estimated utilization updates and
frequency selections.
Let's update util_est at the beginning of enqueue_task_fair(),
which will ensure that all schedutil updates will see the most
updated estimated utilization value for a CPU.
Reported-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Fixes: 7f65ea42eb ("sched/fair: Add util_est on top of PELT")
Link: http://lkml.kernel.org/r/20180524141023.13765-3-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since the refactoring introduced by:
commit 8f111bc357 ("cpufreq/schedutil: Rewrite CPUFREQ_RT support")
we aggregate FAIR utilization only if this class has runnable tasks.
This was mainly due to avoid the risk to stay on an high frequency just
because of the blocked utilization of a CPU not being properly decayed
while the CPU was idle.
However, since:
commit 31e77c93e4 ("sched/fair: Update blocked load when newly idle")
the FAIR blocked utilization is properly decayed also for IDLE CPUs.
This allows us to use the FAIR blocked utilization as a safe mechanism
to gracefully reduce the frequency only if no FAIR tasks show up on a
CPU for a reasonable period of time.
Moreover, we also reduce the frequency drops of CPUs running periodic
tasks which, depending on the task periodicity and the time required
for a frequency switch, was increasing the chances to introduce some
undesirable performance variations.
Reported-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Link: http://lkml.kernel.org/r/20180524141023.13765-2-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following commit:
85f1abe001 ("kthread, sched/wait: Fix kthread_parkme() completion issue")
added a WARN() in the case where we call kthread_park() on an already
parked thread, because the old code wasn't doing the right thing there
and it wasn't at all clear that would happen.
It turns out, this does in fact happen, so we have to deal with it.
Instead of potentially returning early, also wait for the completion.
This does however mean we have to use complete_all() and re-initialize
the completion on re-use.
Reported-by: LKP <lkp@01.org>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel test robot <lkp@intel.com>
Cc: wfg@linux.intel.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 85f1abe001 ("kthread, sched/wait: Fix kthread_parkme() completion issue")
Link: http://lkml.kernel.org/r/20180504091142.GI12235@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-05-24
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Björn Töpel cleans up AF_XDP (removes rebind, explicit cache alignment from uapi, etc).
2) David Ahern adds mtu checks to bpf_ipv{4,6}_fib_lookup() helpers.
3) Jesper Dangaard Brouer adds bulking support to ndo_xdp_xmit.
4) Jiong Wang adds support for indirect and arithmetic shifts to NFP
5) Martin KaFai Lau cleans up BTF uapi and makes the btf_header extensible.
6) Mathieu Xhonneux adds an End.BPF action to seg6local with BPF helpers allowing
to edit/grow/shrink a SRH and apply on a packet generic SRv6 actions.
7) Sandipan Das adds support for bpf2bpf function calls in ppc64 JIT.
8) Yonghong Song adds BPF_TASK_FD_QUERY command for introspection of tracing events.
9) other misc fixes from Gustavo A. R. Silva, Sirio Balmelli, John Fastabend, and Magnus Karlsson
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extending tracepoint xdp:xdp_devmap_xmit in devmap with an err code
allow people to easier identify the reason behind the ndo_xdp_xmit
call to a given driver is failing.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch change the API for ndo_xdp_xmit to support bulking
xdp_frames.
When kernel is compiled with CONFIG_RETPOLINE, XDP sees a huge slowdown.
Most of the slowdown is caused by DMA API indirect function calls, but
also the net_device->ndo_xdp_xmit() call.
Benchmarked patch with CONFIG_RETPOLINE, using xdp_redirect_map with
single flow/core test (CPU E5-1650 v4 @ 3.60GHz), showed
performance improved:
for driver ixgbe: 6,042,682 pps -> 6,853,768 pps = +811,086 pps
for driver i40e : 6,187,169 pps -> 6,724,519 pps = +537,350 pps
With frames avail as a bulk inside the driver ndo_xdp_xmit call,
further optimizations are possible, like bulk DMA-mapping for TX.
Testing without CONFIG_RETPOLINE show the same performance for
physical NIC drivers.
The virtual NIC driver tun sees a huge performance boost, as it can
avoid doing per frame producer locking, but instead amortize the
locking cost over the bulk.
V2: Fix compile errors reported by kbuild test robot <lkp@intel.com>
V4: Isolated ndo, driver changes and callers.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When sending an xdp_frame through xdp_do_redirect call, then error
cases can happen where the xdp_frame needs to be dropped, and
returning an -errno code isn't sufficient/possible any-longer
(e.g. for cpumap case). This is already fully supported, by simply
calling xdp_return_frame.
This patch is an optimization, which provides xdp_return_frame_rx_napi,
which is a faster variant for these error cases. It take advantage of
the protection provided by XDP RX running under NAPI protection.
This change is mostly relevant for drivers using the page_pool
allocator as it can take advantage of this. (Tested with mlx5).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Notice how this allow us get XDP statistic without affecting the XDP
performance, as tracepoint is no-longer activated on a per packet basis.
V5: Spotted by John Fastabend.
Fix 'sent' also counted 'drops' in this patch, a later patch corrected
this, but it was a mistake in this intermediate step.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Like cpumap create queue for xdp frames that will be bulked. For now,
this patch simply invoke ndo_xdp_xmit foreach frame. This happens,
either when the map flush operation is envoked, or when the limit
DEV_MAP_BULK_SIZE is reached.
V5: Avoid memleak on error path in dev_map_update_elem()
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Functionality is the same, but the ndo_xdp_xmit call is now
simply invoked from inside the devmap.c code.
V2: Fix compile issue reported by kbuild test robot <lkp@intel.com>
V5: Cleanups requested by Daniel
- Newlines before func definition
- Use BUILD_BUG_ON checks
- Remove unnecessary use return value store in dev_map_enqueue
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, suppose a userspace application has loaded a bpf program
and attached it to a tracepoint/kprobe/uprobe, and a bpf
introspection tool, e.g., bpftool, wants to show which bpf program
is attached to which tracepoint/kprobe/uprobe. Such attachment
information will be really useful to understand the overall bpf
deployment in the system.
There is a name field (16 bytes) for each program, which could
be used to encode the attachment point. There are some drawbacks
for this approaches. First, bpftool user (e.g., an admin) may not
really understand the association between the name and the
attachment point. Second, if one program is attached to multiple
places, encoding a proper name which can imply all these
attachments becomes difficult.
This patch introduces a new bpf subcommand BPF_TASK_FD_QUERY.
Given a pid and fd, if the <pid, fd> is associated with a
tracepoint/kprobe/uprobe perf event, BPF_TASK_FD_QUERY will return
. prog_id
. tracepoint name, or
. k[ret]probe funcname + offset or kernel addr, or
. u[ret]probe filename + offset
to the userspace.
The user can use "bpftool prog" to find more information about
bpf program itself with prog_id.
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A new extern function, perf_get_event(), is added to return a perf event
given a struct file. This function will be used in later patches.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
While reviewing the verifier code, I recently noticed that the
following two program variants in relation to tail calls can be
loaded.
Variant 1:
# bpftool p d x i 15
0: (15) if r1 == 0x0 goto pc+3
1: (18) r2 = map[id:5]
3: (05) goto pc+2
4: (18) r2 = map[id:6]
6: (b7) r3 = 7
7: (35) if r3 >= 0xa0 goto pc+2
8: (54) (u32) r3 &= (u32) 255
9: (85) call bpf_tail_call#12
10: (b7) r0 = 1
11: (95) exit
# bpftool m s i 5
5: prog_array flags 0x0
key 4B value 4B max_entries 4 memlock 4096B
# bpftool m s i 6
6: prog_array flags 0x0
key 4B value 4B max_entries 160 memlock 4096B
Variant 2:
# bpftool p d x i 20
0: (15) if r1 == 0x0 goto pc+3
1: (18) r2 = map[id:8]
3: (05) goto pc+2
4: (18) r2 = map[id:7]
6: (b7) r3 = 7
7: (35) if r3 >= 0x4 goto pc+2
8: (54) (u32) r3 &= (u32) 3
9: (85) call bpf_tail_call#12
10: (b7) r0 = 1
11: (95) exit
# bpftool m s i 8
8: prog_array flags 0x0
key 4B value 4B max_entries 160 memlock 4096B
# bpftool m s i 7
7: prog_array flags 0x0
key 4B value 4B max_entries 4 memlock 4096B
In both cases the index masking inserted by the verifier in order
to control out of bounds speculation from a CPU via b2157399cc
("bpf: prevent out-of-bounds speculation") seems to be incorrect
in what it is enforcing. In the 1st variant, the mask is applied
from the map with the significantly larger number of entries where
we would allow to a certain degree out of bounds speculation for
the smaller map, and in the 2nd variant where the mask is applied
from the map with the smaller number of entries, we get buggy
behavior since we truncate the index of the larger map.
The original intent from commit b2157399cc is to reject such
occasions where two or more different tail call maps are used
in the same tail call helper invocation. However, the check on
the BPF_MAP_PTR_POISON is never hit since we never poisoned the
saved pointer in the first place! We do this explicitly for map
lookups but in case of tail calls we basically used the tail
call map in insn_aux_data that was processed in the most recent
path which the verifier walked. Thus any prior path that stored
a pointer in insn_aux_data at the helper location was always
overridden.
Fix it by moving the map pointer poison logic into a small helper
that covers both BPF helpers with the same logic. After that in
fixup_bpf_calls() the poison check is then hit for tail calls
and the program rejected. Latter only happens in unprivileged
case since this is the *only* occasion where a rewrite needs to
happen, and where such rewrite is specific to the map (max_entries,
index_mask). In the privileged case the rewrite is generic for
the insn->imm / insn->code update so multiple maps from different
paths can be handled just fine since all the remaining logic
happens in the instruction processing itself. This is similar
to the case of map lookups: in case there is a collision of
maps in fixup_bpf_calls() we must skip the inlined rewrite since
this will turn the generic instruction sequence into a non-
generic one. Thus the patch_call_imm will simply update the
insn->imm location where the bpf_map_lookup_elem() will later
take care of the dispatch. Given we need this 'poison' state
as a check, the information of whether a map is an unpriv_array
gets lost, so enforcing it prior to that needs an additional
state. In general this check is needed since there are some
complex and tail call intensive BPF programs out there where
LLVM tends to generate such code occasionally. We therefore
convert the map_ptr rather into map_state to store all this
w/o extra memory overhead, and the bit whether one of the maps
involved in the collision was from an unpriv_array thus needs
to be retained as well there.
Fixes: b2157399cc ("bpf: prevent out-of-bounds speculation")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds the End.BPF action to the LWT seg6local infrastructure.
This action works like any other seg6local End action, meaning that an IPv6
header with SRH is needed, whose DA has to be equal to the SID of the
action. It will also advance the SRH to the next segment, the BPF program
does not have to take care of this.
Since the BPF program may not be a source of instability in the kernel, it
is important to ensure that the integrity of the packet is maintained
before yielding it back to the IPv6 layer. The hook hence keeps track if
the SRH has been altered through the helpers, and re-validates its
content if needed with seg6_validate_srh. The state kept for validation is
stored in a per-CPU buffer. The BPF program is not allowed to directly
write into the packet, and only some fields of the SRH can be altered
through the helper bpf_lwt_seg6_store_bytes.
Performances profiling has shown that the SRH re-validation does not induce
a significant overhead. If the altered SRH is deemed as invalid, the packet
is dropped.
This validation is also done before executing any action through
bpf_lwt_seg6_action, and will not be performed again if the SRH is not
modified after calling the action.
The BPF program may return 3 types of return codes:
- BPF_OK: the End.BPF action will look up the next destination through
seg6_lookup_nexthop.
- BPF_REDIRECT: if an action has been executed through the
bpf_lwt_seg6_action helper, the BPF program should return this
value, as the skb's destination is already set and the default
lookup should not be performed.
- BPF_DROP : the packet will be dropped.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 152db033d7 (schedutil: Allow cpufreq requests to be made
even when kthread kicked) made changes to prevent utilization updates
from being discarded during processing a previous request, but it
left a small window in which that still can happen in the one-CPU
policy case. Namely, updates coming in after setting work_in_progress
in sugov_update_commit() and clearing it in sugov_work() will still
be dropped due to the work_in_progress check in sugov_update_single().
To close that window, rearrange the code so as to acquire the update
lock around the deferred update branch in sugov_update_single()
and drop the work_in_progress check from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Juri Lelli <juri.lelli@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
This adds new two new fields to struct bpf_prog_info. For
multi-function programs, these fields can be used to pass
a list of the JITed image lengths of each function for a
given program to userspace using the bpf system call with
the BPF_OBJ_GET_INFO_BY_FD command.
This can be used by userspace applications like bpftool
to split up the contiguous JITed dump, also obtained via
the system call, into more relatable chunks corresponding
to each function.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, for multi-function programs, we cannot get the JITed
instructions using the bpf system call's BPF_OBJ_GET_INFO_BY_FD
command. Because of this, userspace tools such as bpftool fail
to identify a multi-function program as being JITed or not.
With the JIT enabled and the test program running, this can be
verified as follows:
# cat /proc/sys/net/core/bpf_jit_enable
1
Before applying this patch:
# bpftool prog list
1: kprobe name foo tag b811aab41a39ad3d gpl
loaded_at 2018-05-16T11:43:38+0530 uid 0
xlated 216B not jited memlock 65536B
...
# bpftool prog dump jited id 1
no instructions returned
After applying this patch:
# bpftool prog list
1: kprobe name foo tag b811aab41a39ad3d gpl
loaded_at 2018-05-16T12:13:01+0530 uid 0
xlated 216B jited 308B memlock 65536B
...
# bpftool prog dump jited id 1
0: nop
4: nop
8: mflr r0
c: std r0,16(r1)
10: stdu r1,-112(r1)
14: std r31,104(r1)
18: addi r31,r1,48
1c: li r3,10
...
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This adds new two new fields to struct bpf_prog_info. For
multi-function programs, these fields can be used to pass
a list of kernel symbol addresses for all functions in a
given program to userspace using the bpf system call with
the BPF_OBJ_GET_INFO_BY_FD command.
When bpf_jit_kallsyms is enabled, we can get the address
of the corresponding kernel symbol for a callee function
and resolve the symbol's name. The address is determined
by adding the value of the call instruction's imm field
to __bpf_call_base. This offset gets assigned to the imm
field by the verifier.
For some architectures, such as powerpc64, the imm field
is not large enough to hold this offset.
We resolve this by:
[1] Assigning the subprog id to the imm field of a call
instruction in the verifier instead of the offset of
the callee's symbol's address from __bpf_call_base.
[2] Determining the address of a callee's corresponding
symbol by using the imm field as an index for the
list of kernel symbol addresses now available from
the program info.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The imm field of a bpf instruction is a signed 32-bit integer.
For JITed bpf-to-bpf function calls, it holds the offset of the
start address of the callee's JITed image from __bpf_call_base.
For some architectures, such as powerpc64, this offset may be
as large as 64 bits and cannot be accomodated in the imm field
without truncation.
We resolve this by:
[1] Additionally using the auxiliary data of each function to
keep a list of start addresses of the JITed images for all
functions determined by the verifier.
[2] Retaining the subprog id inside the off field of the call
instructions and using it to index into the list mentioned
above and lookup the callee's address.
To make sure that the existing JIT compilers continue to work
without requiring changes, we keep the imm field as it is.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Sparse warning:
kernel/bpf/btf.c:1985:34: warning: Variable length array is used.
This patch directly uses ARRAY_SIZE().
Fixes: f80442a4cd ("bpf: btf: Change how section is supported in btf_header")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In commit 7ee681b252 ("workqueue: Convert to state machine callbacks"),
three new function definitions were added: ‘workqueue_prepare_cpu’,
‘workqueue_online_cpu’ and ‘workqueue_offline_cpu’.
Move these function definitions within a CONFIG_SMP block since they are
not used outside of it. This will match function declarations in header
<include/linux/workqueue.h>, and silence the following gcc warning (W=1):
kernel/workqueue.c:4743:5: warning: no previous prototype for ‘workqueue_prepare_cpu’ [-Wmissing-prototypes]
kernel/workqueue.c:4756:5: warning: no previous prototype for ‘workqueue_online_cpu’ [-Wmissing-prototypes]
kernel/workqueue.c:4783:5: warning: no previous prototype for ‘workqueue_offline_cpu’ [-Wmissing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
cgroup_enable_task_cg_lists() incorrectly nests non-irq-safe
tasklist_lock inside irq-safe css_set_lock triggering the following
lockdep warning.
WARNING: possible irq lock inversion dependency detected
4.17.0-rc1-00027-gb37d049 #6 Not tainted
--------------------------------------------------------
systemd/1 just changed the state of lock:
00000000fe57773b (css_set_lock){..-.}, at: cgroup_free+0xf2/0x12a
but this lock took another, SOFTIRQ-unsafe lock in the past:
(tasklist_lock){.+.+}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(tasklist_lock);
local_irq_disable();
lock(css_set_lock);
lock(tasklist_lock);
<Interrupt>
lock(css_set_lock);
*** DEADLOCK ***
The condition is highly unlikely to actually happen especially given
that the path is executed only once per boot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Boqun Feng <boqun.feng@gmail.com>
Introduce helper:
int fork_usermode_blob(void *data, size_t len, struct umh_info *info);
struct umh_info {
struct file *pipe_to_umh;
struct file *pipe_from_umh;
pid_t pid;
};
that GPLed kernel modules (signed or unsigned) can use it to execute part
of its own data as swappable user mode process.
The kernel will do:
- allocate a unique file in tmpfs
- populate that file with [data, data + len] bytes
- user-mode-helper code will do_execve that file and, before the process
starts, the kernel will create two unix pipes for bidirectional
communication between kernel module and umh
- close tmpfs file, effectively deleting it
- the fork_usermode_blob will return zero on success and populate
'struct umh_info' with two unix pipes and the pid of the user process
As the first step in the development of the bpfilter project
the fork_usermode_blob() helper is introduced to allow user mode code
to be invoked from a kernel module. The idea is that user mode code plus
normal kernel module code are built as part of the kernel build
and installed as traditional kernel module into distro specified location,
such that from a distribution point of view, there is
no difference between regular kernel modules and kernel modules + umh code.
Such modules can be signed, modprobed, rmmod, etc. The use of this new helper
by a kernel module doesn't make it any special from kernel and user space
tooling point of view.
Such approach enables kernel to delegate functionality traditionally done
by the kernel modules into the user space processes (either root or !root) and
reduces security attack surface of the new code. The buggy umh code would crash
the user process, but not the kernel. Another advantage is that umh code
of the kernel module can be debugged and tested out of user space
(e.g. opening the possibility to run clang sanitizers, fuzzers or
user space test suites on the umh code).
In case of the bpfilter project such architecture allows complex control plane
to be done in the user space while bpf based data plane stays in the kernel.
Since umh can crash, can be oom-ed by the kernel, killed by the admin,
the kernel module that uses them (like bpfilter) needs to manage life
time of umh on its own via two unix pipes and the pid of umh.
The exit code of such kernel module should kill the umh it started,
so that rmmod of the kernel module will cleanup the corresponding umh.
Just like if the kernel module does kmalloc() it should kfree() it
in the exit code.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In "struct bpf_map_info", the name "btf_id", "btf_key_id" and "btf_value_id"
could cause confusion because the "id" of "btf_id" means the BPF obj id
given to the BTF object while
"btf_key_id" and "btf_value_id" means the BTF type id within
that BTF object.
To make it clear, btf_key_id and btf_value_id are
renamed to btf_key_type_id and btf_value_type_id.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch does the followings:
1. Limit BTF_MAX_TYPES and BTF_MAX_NAME_OFFSET to 64k. We can
raise it later.
2. Remove the BTF_TYPE_PARENT and BTF_STR_TBL_ELF_ID. They are
currently encoded at the highest bit of a u32.
It is because the current use case does not require supporting
parent type (i.e type_id referring to a type in another BTF file).
It also does not support referring to a string in ELF.
The BTF_TYPE_PARENT and BTF_STR_TBL_ELF_ID checks are replaced
by BTF_TYPE_ID_CHECK and BTF_STR_OFFSET_CHECK which are
defined in btf.c instead of uapi/linux/btf.h.
3. Limit the BTF_INFO_KIND from 5 bits to 4 bits which is enough.
There is unused bits headroom if we ever needed it later.
4. The root bit in BTF_INFO is also removed because it is not
used in the current use case.
5. Remove BTF_INT_VARARGS since func type is not supported now.
The BTF_INT_ENCODING is limited to 4 bits instead of 8 bits.
The above can be added back later because the verifier
ensures the unused bits are zeros.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Instead of ingoring the array->index_type field. Enforce that
it must be a BTF_KIND_INT in size 1/2/4/8 bytes.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
There are currently unused section descriptions in the btf_header. Those
sections are here to support future BTF use cases. For example, the
func section (func_off) is to support function signature (e.g. the BPF
prog function signature).
Instead of spelling out all potential sections up-front in the btf_header.
This patch makes changes to btf_header such that extending it (e.g. adding
a section) is possible later. The unused ones can be removed for now and
they can be added back later.
This patch:
1. adds a hdr_len to the btf_header. It will allow adding
sections (and other info like parent_label and parent_name)
later. The check is similar to the existing bpf_attr.
If a user passes in a longer hdr_len, the kernel
ensures the extra tailing bytes are 0.
2. allows the section order in the BTF object to be
different from its sec_off order in btf_header.
3. each sec_off is followed by a sec_len. It must not have gap or
overlapping among sections.
The string section is ensured to be at the end due to the 4 bytes
alignment requirement of the type section.
The above changes will allow enough flexibility to
add new sections (and other info) to the btf_header later.
This patch also removes an unnecessary !err check
at the end of btf_parse().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch exposes check_uarg_tail_zero() which will
be reused by a later BTF patch. Its name is changed to
bpf_check_uarg_tail_zero().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently there is a chance of a schedutil cpufreq update request to be
dropped if there is a pending update request. This pending request can
be delayed if there is a scheduling delay of the irq_work and the wake
up of the schedutil governor kthread.
A very bad scenario is when a schedutil request was already just made,
such as to reduce the CPU frequency, then a newer request to increase
CPU frequency (even sched deadline urgent frequency increase requests)
can be dropped, even though the rate limits suggest that its Ok to
process a request. This is because of the way the work_in_progress flag
is used.
This patch improves the situation by allowing new requests to happen
even though the old one is still being processed. Note that in this
approach, if an irq_work was already issued, we just update next_freq
and don't bother to queue another request so there's no extra work being
done to make this happen.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This routine checks if the CPU running this code belongs to the policy
of the target CPU or if not, can it do remote DVFS for it remotely. But
the current name of it implies as if it is only about doing remote
updates.
Rename it to make it more relevant.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The x86/mtrr code does horrific things because hardware. It uses
stop_machine_from_inactive_cpu(), which does a wakeup (of the stopper
thread on another CPU), which uses RCU, all before the CPU is onlined.
RCU complains about this, because wakeups use RCU and RCU does
(rightfully) not consider offline CPUs for grace-periods.
Fix this by initializing RCU way early in the MTRR case.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: Add !SMP support, per 0day Test Robot report. ]
In preparation for fixing dax-dma-vs-unmap issues, filesystems need to
be able to rely on the fact that they will get wakeups on dev_pagemap
page-idle events. Introduce MEMORY_DEVICE_FS_DAX and
generic_dax_page_free() as common indicator / infrastructure for dax
filesytems to require. With this change there are no users of the
MEMORY_DEVICE_HOST designation, so remove it.
The HMM sub-system extended dev_pagemap to arrange a callback when a
dev_pagemap managed page is freed. Since a dev_pagemap page is free /
idle when its reference count is 1 it requires an additional branch to
check the page-type at put_page() time. Given put_page() is a hot-path
we do not want to incur that check if HMM is not in use, so a static
branch is used to avoid that overhead when not necessary.
Now, the FS_DAX implementation wants to reuse this mechanism for
receiving dev_pagemap ->page_free() callbacks. Rework the HMM-specific
static-key into a generic mechanism that either HMM or FS_DAX code paths
can enable.
For ARCH=um builds, and any other arch that lacks ZONE_DEVICE support,
care must be taken to compile out the DEV_PAGEMAP_OPS infrastructure.
However, we still need to support FS_DAX in the FS_DAX_LIMITED case
implemented by the s390/dcssblk driver.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The iowait boosting code has been recently updated to add a progressive
boosting behavior which allows to be less aggressive in boosting tasks
doing only sporadic IO operations, thus being more energy efficient for
example on mobile platforms.
The current code is now however a bit convoluted. Some functionalities
(e.g. iowait boost reset) are replicated in different paths and their
documentation is slightly misaligned.
Let's cleanup the code by consolidating all the IO wait boosting related
functionality within within few dedicated functions and better define
their role:
- sugov_iowait_boost: set/increase the IO wait boost of a CPU
- sugov_iowait_apply: apply/reduce the IO wait boost of a CPU
Both these two function are used at every sugov update and they make
use of a unified IO wait boost reset policy provided by:
- sugov_iowait_reset: reset/disable the IO wait boost of a CPU
if a CPU is not updated for more then one tick
This makes possible a cleaner and more self-contained design for the IO
wait boosting code since the rest of the sugov update routines, both for
single and shared frequency domains, follow the same template:
/* Configure IO boost, if required */
sugov_iowait_boost()
/* Return here if freq change is in progress or throttled */
/* Collect and aggregate utilization information */
sugov_get_util()
sugov_aggregate_util()
/*
* Add IO boost, if currently enabled, on top of the aggregated
* utilization value
*/
sugov_iowait_apply()
As a extra bonus, let's also add the documentation for the new
functions and better align the in-code documentation.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A more energy efficient update of the IO wait boosting mechanism has
been introduced in:
commit a5a0809bc5 ("cpufreq: schedutil: Make iowait boost more energy efficient")
where the boost value is expected to be:
- doubled at each successive wakeup from IO
staring from the minimum frequency supported by a CPU
- reset when a CPU is not updated for more then one tick
by either disabling the IO wait boost or resetting its value to the
minimum frequency if this new update requires an IO boost.
This approach is supposed to "ignore" boosting for sporadic wakeups from
IO, while still getting the frequency boosted to the maximum to benefit
long sequence of wakeup from IO operations.
However, these assumptions are not always satisfied.
For example, when an IO boosted CPU enters idle for more the one tick
and then wakes up after an IO wait, since in sugov_set_iowait_boost() we
first check the IOWAIT flag, we keep doubling the iowait boost instead
of restarting from the minimum frequency value.
This misbehavior could happen mainly on non-shared frequency domains,
thus defeating the energy efficiency optimization, but it can also
happen on shared frequency domain systems.
Let fix this issue in sugov_set_iowait_boost() by:
- first check the IO wait boost reset conditions
to eventually reset the boost value
- then applying the correct IO boost value
if required by the caller
Fixes: a5a0809bc5 (cpufreq: schedutil: Make iowait boost more energy efficient)
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
The audit_filter_rules() function in auditsc.c compared the session ID
with the credentials of the current task, while it should use the
credentials of the task given to audit_filter_rules() as a parameter
(tsk).
GitHub issue:
https://github.com/linux-audit/audit-kernel/issues/82
Fixes: 8fae477056 ("audit: add support for session ID user filter")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
[PM: not user visible, dropped stable]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Merge speculative store buffer bypass fixes from Thomas Gleixner:
- rework of the SPEC_CTRL MSR management to accomodate the new fancy
SSBD (Speculative Store Bypass Disable) bit handling.
- the CPU bug and sysfs infrastructure for the exciting new Speculative
Store Bypass 'feature'.
- support for disabling SSB via LS_CFG MSR on AMD CPUs including
Hyperthread synchronization on ZEN.
- PRCTL support for dynamic runtime control of SSB
- SECCOMP integration to automatically disable SSB for sandboxed
processes with a filter flag for opt-out.
- KVM integration to allow guests fiddling with SSBD including the new
software MSR VIRT_SPEC_CTRL to handle the LS_CFG based oddities on
AMD.
- BPF protection against SSB
.. this is just the core and x86 side, other architecture support will
come separately.
* 'speck-v20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (49 commits)
bpf: Prevent memory disambiguation attack
x86/bugs: Rename SSBD_NO to SSB_NO
KVM: SVM: Implement VIRT_SPEC_CTRL support for SSBD
x86/speculation, KVM: Implement support for VIRT_SPEC_CTRL/LS_CFG
x86/bugs: Rework spec_ctrl base and mask logic
x86/bugs: Remove x86_spec_ctrl_set()
x86/bugs: Expose x86_spec_ctrl_base directly
x86/bugs: Unify x86_spec_ctrl_{set_guest,restore_host}
x86/speculation: Rework speculative_store_bypass_update()
x86/speculation: Add virtualized speculative store bypass disable support
x86/bugs, KVM: Extend speculation control for VIRT_SPEC_CTRL
x86/speculation: Handle HT correctly on AMD
x86/cpufeatures: Add FEATURE_ZEN
x86/cpufeatures: Disentangle SSBD enumeration
x86/cpufeatures: Disentangle MSR_SPEC_CTRL enumeration from IBRS
x86/speculation: Use synthetic bits for IBRS/IBPB/STIBP
KVM: SVM: Move spec control call after restore of GS
x86/cpu: Make alternative_msr_write work for 32-bit code
x86/bugs: Fix the parameters alignment and missing void
x86/bugs: Make cpu_show_common() static
...
Pull networking fixes from David Miller:
1) Fix refcounting bug for connections in on-packet scheduling mode of
IPVS, from Julian Anastasov.
2) Set network header properly in AF_PACKET's packet_snd, from Willem
de Bruijn.
3) Fix regressions in 3c59x by converting to generic DMA API. It was
relying upon the hack that the PCI DMA interfaces would accept NULL
for EISA devices. From Christoph Hellwig.
4) Remove RDMA devices before unregistering netdev in QEDE driver, from
Michal Kalderon.
5) Use after free in TUN driver ptr_ring usage, from Jason Wang.
6) Properly check for missing netlink attributes in SMC_PNETID
requests, from Eric Biggers.
7) Set DMA mask before performaing any DMA operations in vmxnet3
driver, from Regis Duchesne.
8) Fix mlx5 build with SMP=n, from Saeed Mahameed.
9) Classifier fixes in bcm_sf2 driver from Florian Fainelli.
10) Tuntap use after free during release, from Jason Wang.
11) Don't use stack memory in scatterlists in tls code, from Matt
Mullins.
12) Not fully initialized flow key object in ipv4 routing code, from
David Ahern.
13) Various packet headroom bug fixes in ip6_gre driver, from Petr
Machata.
14) Remove queues from XPS maps using correct index, from Amritha
Nambiar.
15) Fix use after free in sock_diag, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (64 commits)
net: ip6_gre: fix tunnel metadata device sharing.
cxgb4: fix offset in collecting TX rate limit info
net: sched: red: avoid hashing NULL child
sock_diag: fix use-after-free read in __sk_free
sh_eth: Change platform check to CONFIG_ARCH_RENESAS
net: dsa: Do not register devlink for unused ports
net: Fix a bug in removing queues from XPS map
bpf: fix truncated jump targets on heavy expansions
bpf: parse and verdict prog attach may race with bpf map update
bpf: sockmap update rollback on error can incorrectly dec prog refcnt
net: test tailroom before appending to linear skb
net: ip6_gre: Fix ip6erspan hlen calculation
net: ip6_gre: Split up ip6gre_changelink()
net: ip6_gre: Split up ip6gre_newlink()
net: ip6_gre: Split up ip6gre_tnl_change()
net: ip6_gre: Split up ip6gre_tnl_link_config()
net: ip6_gre: Fix headroom request in ip6erspan_tunnel_xmit()
net: ip6_gre: Request headroom in __gre6_xmit()
selftests/bpf: check return value of fopen in test_verifier.c
erspan: fix invalid erspan version.
...
The worker struct could already be freed when wq_worker_comm() tries
to access it for reporting. This patch protects PF_WQ_WORKER
modifications with wq_pool_attach_mutex and makes wq_worker_comm()
test the flag before dereferencing worker from kthread_data(), which
ensures that it only dereferences when the worker struct is valid.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Lai Jiangshan <jiangshanlai@gmail.com>
Fixes: 6b59808bfe ("workqueue: Show the latest workqueue name in /proc/PID/{comm,stat,status}")
Pull UP timer fix from Thomas Gleixner:
"Work around the for_each_cpu() oddity on UP kernels in the tick
broadcast code which causes boot failures because the CPU0 bit is
always reported as set independent of the cpumask content"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Use for_each_cpu() specially on UP kernels
Pull scheduler fixlets from Thomas Gleixner:
"Three trivial fixlets for the scheduler:
- move print_rt_rq() and print_dl_rq() declarations to the right
place
- make grub_reclaim() static
- fix the bogus documentation reference in Kconfig"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix documentation file path
sched/deadline: Make the grub_reclaim() function static
sched/debug: Move the print_rt_rq() and print_dl_rq() declarations to kernel/sched/sched.h
I have run into a couple of drivers using current_kernel_time()
suffering from the y2038 problem, and they could be converted
to using ktime_t, but don't have interfaces that skip the nanosecond
calculation at the moment.
This introduces ktime_get_coarse_with_offset() as a simpler
variant of ktime_get_with_offset(), and adds wrappers for the
three time domains we support with the existing function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: y2038@lists.linaro.org
Cc: John Stultz <john.stultz@linaro.org>
Link: https://lkml.kernel.org/r/20180427134016.2525989-5-arnd@arndb.de
The current_kernel_time64, get_monotonic_coarse64, getrawmonotonic64,
get_monotonic_boottime64 and timekeeping_clocktai64 interfaces have
rather inconsistent naming, and they differ in the calling conventions
by passing the output either by reference or as a return value.
Rename them to ktime_get_coarse_real_ts64, ktime_get_coarse_ts64,
ktime_get_raw_ts64, ktime_get_boottime_ts64 and ktime_get_clocktai_ts64
respectively, and provide the interfaces with macros or inline
functions as needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: y2038@lists.linaro.org
Cc: John Stultz <john.stultz@linaro.org>
Link: https://lkml.kernel.org/r/20180427134016.2525989-4-arnd@arndb.de
In a move to make ktime_get_*() the preferred driver interface into the
timekeeping code, sanitizes ktime_get_real_ts64() to be a proper exported
symbol rather than an alias for getnstimeofday64().
The internal __getnstimeofday64() is no longer used, so remove that
and merge it into ktime_get_real_ts64().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: y2038@lists.linaro.org
Cc: John Stultz <john.stultz@linaro.org>
Link: https://lkml.kernel.org/r/20180427134016.2525989-3-arnd@arndb.de
At this point, we have converted most of the kernel to use timespec64
consistently in place of timespec, so it seems it's time to make
timespec64 the native structure and define timespec in terms of that
one on 64-bit architectures.
Starting with gcc-5, the compiler can completely optimize away the
timespec_to_timespec64 and timespec64_to_timespec functions on 64-bit
architectures. With older compilers, we introduce a couple of extra
copies of local variables, but those are easily avoided by using
the timespec64 based interfaces consistently, as we do in most of the
important code paths already.
The main upside of removing the hack is that printing the tv_sec
field of a timespec64 structure can now use the %lld format
string on all architectures without a cast to time64_t. Without
this patch, the field is a 'long' type and would have to be printed
using %ld on 64-bit architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: y2038@lists.linaro.org
Cc: John Stultz <john.stultz@linaro.org>
Link: https://lkml.kernel.org/r/20180427134016.2525989-2-arnd@arndb.de
Currently sk_msg programs only have access to the raw data. However,
it is often useful when building policies to have the policies specific
to the socket endpoint. This allows using the socket tuple as input
into filters, etc.
This patch adds ctx access to the sock fields.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Use the existing audit_log_session_info() function rather than
hardcoding its functionality.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
There can be a lot of workqueue workers and they all show up with the
cryptic kworker/* names making it difficult to understand which is
doing what and how they came to be.
# ps -ef | grep kworker
root 4 2 0 Feb25 ? 00:00:00 [kworker/0:0H]
root 6 2 0 Feb25 ? 00:00:00 [kworker/u112:0]
root 19 2 0 Feb25 ? 00:00:00 [kworker/1:0H]
root 25 2 0 Feb25 ? 00:00:00 [kworker/2:0H]
root 31 2 0 Feb25 ? 00:00:00 [kworker/3:0H]
...
This patch makes workqueue workers report the latest workqueue it was
executing for through /proc/PID/{comm,stat,status}. The extra
information is appended to the kthread name with intervening '+' if
currently executing, otherwise '-'.
# cat /proc/25/comm
kworker/2:0-events_power_efficient
# cat /proc/25/stat
25 (kworker/2:0-events_power_efficient) I 2 0 0 0 -1 69238880 0 0...
# grep Name /proc/25/status
Name: kworker/2:0-events_power_efficient
Unfortunately, ps(1) truncates comm to 15 characters,
# ps 25
PID TTY STAT TIME COMMAND
25 ? I 0:00 [kworker/2:0-eve]
making it a lot less useful; however, this should be an easy fix from
ps(1) side.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Craig Small <csmall@enc.com.au>
Work functions can use set_worker_desc() to improve the visibility of
what the worker task is doing. Currently, the desc field is unset at
the beginning of each execution and there is a separate field to track
the field is set during the current execution.
Instead of leaving empty till desc is set, worker->desc can be used to
remember the last workqueue the worker worked on by default and users
that use set_worker_desc() can override it to something more
informative as necessary.
This simplifies desc handling and helps tracking the last workqueue
that the worker exected on to improve visibility.
Signed-off-by: Tejun Heo <tj@kernel.org>
For historical reasons, the worker attach/detach functions don't
currently manage worker->pool and the callers are manually and
inconsistently updating it.
This patch moves worker->pool updates into the worker attach/detach
functions. This makes worker->pool consistent and clearly defines how
worker->pool updates are synchronized.
This will help later workqueue visibility improvements by allowing
safe access to workqueue information from worker->task.
Signed-off-by: Tejun Heo <tj@kernel.org>
To improve workqueue visibility, we want to be able to access
workqueue information from worker tasks. The per-pool attach mutex
makes that difficult because there's no way of stabilizing task ->
worker pool association without knowing the pool first.
Worker attach/detach is a slow path and there's no need for different
pools to be able to perform them concurrently. This patch replaces
the per-pool attach_mutex with global wq_pool_attach_mutex to prepare
for visibility improvement changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
As a prerequisite, complement commit 3d1cb2059d ("workqueue: include
workqueue info when printing debug dump of a worker task") to be usable with
kernel modules by exporting the symbol set_worker_desc(). Current built-in
user was introduced with commit ef3b101925 ("writeback: set worker desc to
identify writeback workers in task dumps").
Can help distinguishing work items which do not have adapter scope.
Description is printed out with task dump for debugging on WARN, BUG, panic,
or magic-sysrq [show-task-states(t)].
Example:
$ echo 0 >| /sys/bus/ccw/drivers/zfcp/0.0.1880/0x50050763031bd327/failed &
$ echo 't' >| /proc/sysrq-trigger
$ dmesg
sysrq: SysRq : Show State
task PC stack pid father
...
zfcp_q_0.0.1880 S14640 2165 2 0x02000000
Call Trace:
([<00000000009df464>] __schedule+0xbf4/0xc78)
[<00000000009df57c>] schedule+0x94/0xc0
[<0000000000168654>] rescuer_thread+0x33c/0x3a0
[<000000000016f8be>] kthread+0x166/0x178
[<00000000009e71f2>] kernel_thread_starter+0x6/0xc
[<00000000009e71ec>] kernel_thread_starter+0x0/0xc
no locks held by zfcp_q_0.0.1880/2165.
...
kworker/u512:2 D11280 2193 2 0x02000000
Workqueue: zfcp_q_0.0.1880 zfcp_scsi_rport_work [zfcp] (zrpd-50050763031bd327)
^^^^^^^^^^^^^^^^^^^^^
Call Trace:
([<00000000009df464>] __schedule+0xbf4/0xc78)
[<00000000009df57c>] schedule+0x94/0xc0
[<00000000009e50c0>] schedule_timeout+0x488/0x4d0
[<00000000001e425c>] msleep+0x5c/0x78 >>test code only<<
[<000003ff8008a21e>] zfcp_scsi_rport_work+0xbe/0x100 [zfcp]
[<0000000000167154>] process_one_work+0x3b4/0x718
[<000000000016771c>] worker_thread+0x264/0x408
[<000000000016f8be>] kthread+0x166/0x178
[<00000000009e71f2>] kernel_thread_starter+0x6/0xc
[<00000000009e71ec>] kernel_thread_starter+0x0/0xc
2 locks held by kworker/u512:2/2193:
#0: (name){++++.+}, at: [<0000000000166f4e>] process_one_work+0x1ae/0x718
#1: ((&(&port->rport_work)->work)){+.+.+.}, at: [<0000000000166f4e>] process_one_work+0x1ae/0x718
...
=============================================
Showing busy workqueues and worker pools:
workqueue zfcp_q_0.0.1880: flags=0x2000a
pwq 512: cpus=0-255 flags=0x4 nice=0 active=1/1
in-flight: 2193:zfcp_scsi_rport_work [zfcp]
pool 512: cpus=0-255 flags=0x4 nice=0 hung=0s workers=4 idle: 5 2354 2311
Work items with adapter scope are already identified by the workqueue name
"zfcp_q_<devbusid>" and the work item function name.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clean up SPDX-License-Identifier and removing licensing leftovers.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Before changing the arguments of the functions fsnotify_add_mark()
and fsnotify_add_mark_locked(), convert most callers to use a wrapper.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
inode_mark and vfsmount_mark arguments are passed to handle_event()
operation as function arguments as well as on iter_info struct.
The difference is that iter_info struct may contain marks that should
not be handled and are represented as NULL arguments to inode_mark or
vfsmount_mark.
Instead of passing the inode_mark and vfsmount_mark arguments, add
a report_mask member to iter_info struct to indicate which marks should
be handled, versus marks that should only be kept alive during user
wait.
This change is going to be used for passing more mark types
with handle_event() (i.e. super block marks).
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Since the grub_reclaim() function can be made static, make it so.
Silences the following GCC warning (W=1):
kernel/sched/deadline.c:1120:5: warning: no previous prototype for ‘grub_reclaim’ [-Wmissing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180516200902.959-1-malat@debian.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In the following commit:
6b55c9654f ("sched/debug: Move print_cfs_rq() declaration to kernel/sched/sched.h")
the print_cfs_rq() prototype was added to <kernel/sched/sched.h>,
right next to the prototypes for print_cfs_stats(), print_rt_stats()
and print_dl_stats().
Finish this previous commit and also move related prototypes for
print_rt_rq() and print_dl_rq().
Remove existing extern declarations now that they not needed anymore.
Silences the following GCC warning, triggered by W=1:
kernel/sched/debug.c:573:6: warning: no previous prototype for ‘print_rt_rq’ [-Wmissing-prototypes]
kernel/sched/debug.c:603:6: warning: no previous prototype for ‘print_dl_rq’ [-Wmissing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180516195348.30426-1-malat@debian.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Recently during testing, I ran into the following panic:
[ 207.892422] Internal error: Accessing user space memory outside uaccess.h routines: 96000004 [#1] SMP
[ 207.901637] Modules linked in: binfmt_misc [...]
[ 207.966530] CPU: 45 PID: 2256 Comm: test_verifier Tainted: G W 4.17.0-rc3+ #7
[ 207.974956] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB18A 03/31/2017
[ 207.982428] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 207.987214] pc : bpf_skb_load_helper_8_no_cache+0x34/0xc0
[ 207.992603] lr : 0xffff000000bdb754
[ 207.996080] sp : ffff000013703ca0
[ 207.999384] x29: ffff000013703ca0 x28: 0000000000000001
[ 208.004688] x27: 0000000000000001 x26: 0000000000000000
[ 208.009992] x25: ffff000013703ce0 x24: ffff800fb4afcb00
[ 208.015295] x23: ffff00007d2f5038 x22: ffff00007d2f5000
[ 208.020599] x21: fffffffffeff2a6f x20: 000000000000000a
[ 208.025903] x19: ffff000009578000 x18: 0000000000000a03
[ 208.031206] x17: 0000000000000000 x16: 0000000000000000
[ 208.036510] x15: 0000ffff9de83000 x14: 0000000000000000
[ 208.041813] x13: 0000000000000000 x12: 0000000000000000
[ 208.047116] x11: 0000000000000001 x10: ffff0000089e7f18
[ 208.052419] x9 : fffffffffeff2a6f x8 : 0000000000000000
[ 208.057723] x7 : 000000000000000a x6 : 00280c6160000000
[ 208.063026] x5 : 0000000000000018 x4 : 0000000000007db6
[ 208.068329] x3 : 000000000008647a x2 : 19868179b1484500
[ 208.073632] x1 : 0000000000000000 x0 : ffff000009578c08
[ 208.078938] Process test_verifier (pid: 2256, stack limit = 0x0000000049ca7974)
[ 208.086235] Call trace:
[ 208.088672] bpf_skb_load_helper_8_no_cache+0x34/0xc0
[ 208.093713] 0xffff000000bdb754
[ 208.096845] bpf_test_run+0x78/0xf8
[ 208.100324] bpf_prog_test_run_skb+0x148/0x230
[ 208.104758] sys_bpf+0x314/0x1198
[ 208.108064] el0_svc_naked+0x30/0x34
[ 208.111632] Code: 91302260 f9400001 f9001fa1 d2800001 (29500680)
[ 208.117717] ---[ end trace 263cb8a59b5bf29f ]---
The program itself which caused this had a long jump over the whole
instruction sequence where all of the inner instructions required
heavy expansions into multiple BPF instructions. Additionally, I also
had BPF hardening enabled which requires once more rewrites of all
constant values in order to blind them. Each time we rewrite insns,
bpf_adj_branches() would need to potentially adjust branch targets
which cross the patchlet boundary to accommodate for the additional
delta. Eventually that lead to the case where the target offset could
not fit into insn->off's upper 0x7fff limit anymore where then offset
wraps around becoming negative (in s16 universe), or vice versa
depending on the jump direction.
Therefore it becomes necessary to detect and reject any such occasions
in a generic way for native eBPF and cBPF to eBPF migrations. For
the latter we can simply check bounds in the bpf_convert_filter()'s
BPF_EMIT_JMP helper macro and bail out once we surpass limits. The
bpf_patch_insn_single() for native eBPF (and cBPF to eBPF in case
of subsequent hardening) is a bit more complex in that we need to
detect such truncations before hitting the bpf_prog_realloc(). Thus
the latter is split into an extra pass to probe problematic offsets
on the original program in order to fail early. With that in place
and carefully tested I no longer hit the panic and the rewrites are
rejected properly. The above example panic I've seen on bpf-next,
though the issue itself is generic in that a guard against this issue
in bpf seems more appropriate in this case.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In the sockmap design BPF programs (SK_SKB_STREAM_PARSER,
SK_SKB_STREAM_VERDICT and SK_MSG_VERDICT) are attached to the sockmap
map type and when a sock is added to the map the programs are used by
the socket. However, sockmap updates from both userspace and BPF
programs can happen concurrently with the attach and detach of these
programs.
To resolve this we use the bpf_prog_inc_not_zero and a READ_ONCE()
primitive to ensure the program pointer is not refeched and
possibly NULL'd before the refcnt increment. This happens inside
a RCU critical section so although the pointer reference in the map
object may be NULL (by a concurrent detach operation) the reference
from READ_ONCE will not be free'd until after grace period. This
ensures the object returned by READ_ONCE() is valid through the
RCU criticl section and safe to use as long as we "know" it may
be free'd shortly.
Daniel spotted a case in the sock update API where instead of using
the READ_ONCE() program reference we used the pointer from the
original map, stab->bpf_{verdict|parse|txmsg}. The problem with this
is the logic checks the object returned from the READ_ONCE() is not
NULL and then tries to reference the object again but using the
above map pointer, which may have already been NULL'd by a parallel
detach operation. If this happened bpf_porg_inc_not_zero could
dereference a NULL pointer.
Fix this by using variable returned by READ_ONCE() that is checked
for NULL.
Fixes: 2f857d0460 ("bpf: sockmap, remove STRPARSER map_flags and add multi-map support")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If the user were to only attach one of the parse or verdict programs
then it is possible a subsequent sockmap update could incorrectly
decrement the refcnt on the program. This happens because in the
rollback logic, after an error, we have to decrement the program
reference count when its been incremented. However, we only increment
the program reference count if the user has both a verdict and a
parse program. The reason for this is because, at least at the
moment, both are required for any one to be meaningful. The problem
fixed here is in the rollback path we decrement the program refcnt
even if only one existing. But we never incremented the refcnt in
the first place creating an imbalance.
This patch fixes the error path to handle this case.
Fixes: 2f857d0460 ("bpf: sockmap, remove STRPARSER map_flags and add multi-map support")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
`e' is being freed twice.
Fix this by removing one of the kfree() calls.
Addresses-Coverity-ID: 1468983 ("Double free")
Fixes: 8111038444 ("bpf: sockmap, add hash map support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
There is a potential execution path in which variable err is
returned without being properly initialized previously.
Fix this by initializing variable err to 0.
Addresses-Coverity-ID: 1468964 ("Uninitialized scalar variable")
Fixes: e5cd3abcb3 ("bpf: sockmap, refactor sockmap routines to work with hashmap")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Recognizing that the loginuid is an internal audit value, use an access
function to retrieve the audit loginuid value for the task rather than
reaching directly into the task struct to get it.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
On the rebase of the following commit on the new seccomp actions_logged
function, one audit_context access was missed.
commit cdfb6b341f
("audit: use inline function to get audit context")
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-05-17
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Provide a new BPF helper for doing a FIB and neighbor lookup
in the kernel tables from an XDP or tc BPF program. The helper
provides a fast-path for forwarding packets. The API supports
IPv4, IPv6 and MPLS protocols, but currently IPv4 and IPv6 are
implemented in this initial work, from David (Ahern).
2) Just a tiny diff but huge feature enabled for nfp driver by
extending the BPF offload beyond a pure host processing offload.
Offloaded XDP programs are allowed to set the RX queue index and
thus opening the door for defining a fully programmable RSS/n-tuple
filter replacement. Once BPF decided on a queue already, the device
data-path will skip the conventional RSS processing completely,
from Jakub.
3) The original sockmap implementation was array based similar to
devmap. However unlike devmap where an ifindex has a 1:1 mapping
into the map there are use cases with sockets that need to be
referenced using longer keys. Hence, sockhash map is added reusing
as much of the sockmap code as possible, from John.
4) Introduce BTF ID. The ID is allocatd through an IDR similar as
with BPF maps and progs. It also makes BTF accessible to user
space via BPF_BTF_GET_FD_BY_ID and adds exposure of the BTF data
through BPF_OBJ_GET_INFO_BY_FD, from Martin.
5) Enable BPF stackmap with build_id also in NMI context. Due to the
up_read() of current->mm->mmap_sem build_id cannot be parsed.
This work defers the up_read() via a per-cpu irq_work so that
at least limited support can be enabled, from Song.
6) Various BPF JIT follow-up cleanups and fixups after the LD_ABS/LD_IND
JIT conversion as well as implementation of an optimized 32/64 bit
immediate load in the arm64 JIT that allows to reduce the number of
emitted instructions; in case of tested real-world programs they
were shrinking by three percent, from Daniel.
7) Add ifindex parameter to the libbpf loader in order to enable
BPF offload support. Right now only iproute2 can load offloaded
BPF and this will also enable libbpf for direct integration into
other applications, from David (Beckett).
8) Convert the plain text documentation under Documentation/bpf/ into
RST format since this is the appropriate standard the kernel is
moving to for all documentation. Also add an overview README.rst,
from Jesper.
9) Add __printf verification attribute to the bpf_verifier_vlog()
helper. Though it uses va_list we can still allow gcc to check
the format string, from Mathieu.
10) Fix a bash reference in the BPF selftest's Makefile. The '|& ...'
is a bash 4.0+ feature which is not guaranteed to be available
when calling out to shell, therefore use a more portable variant,
from Joe.
11) Fix a 64 bit division in xdp_umem_reg() by using div_u64()
instead of relying on the gcc built-in, from Björn.
12) Fix a sock hashmap kmalloc warning reported by syzbot when an
overly large key size is used in hashmap then causing overflows
in htab->elem_size. Reject bogus attr->key_size early in the
sock_hash_alloc(), from Yonghong.
13) Ensure in BPF selftests when urandom_read is being linked that
--build-id is always enabled so that test_stacktrace_build_id[_nmi]
won't be failing, from Alexei.
14) Add bitsperlong.h as well as errno.h uapi headers into the tools
header infrastructure which point to one of the arch specific
uapi headers. This was needed in order to fix a build error on
some systems for the BPF selftests, from Sirio.
15) Allow for short options to be used in the xdp_monitor BPF sample
code. And also a bpf.h tools uapi header sync in order to fix a
selftest build failure. Both from Prashant.
16) More formally clarify the meaning of ID in the direct packet access
section of the BPF documentation, from Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error happens in the update sockmap element logic also pass
the err up to the user.
Fixes: e5cd3abcb3 ("bpf: sockmap, refactor sockmap routines to work with hashmap")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
syzbot reported a kernel warning below:
WARNING: CPU: 0 PID: 4499 at mm/slab_common.c:996 kmalloc_slab+0x56/0x70 mm/slab_common.c:996
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 4499 Comm: syz-executor050 Not tainted 4.17.0-rc3+ #9
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1b9/0x294 lib/dump_stack.c:113
panic+0x22f/0x4de kernel/panic.c:184
__warn.cold.8+0x163/0x1b3 kernel/panic.c:536
report_bug+0x252/0x2d0 lib/bug.c:186
fixup_bug arch/x86/kernel/traps.c:178 [inline]
do_error_trap+0x1de/0x490 arch/x86/kernel/traps.c:296
do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:315
invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:992
RIP: 0010:kmalloc_slab+0x56/0x70 mm/slab_common.c:996
RSP: 0018:ffff8801d907fc58 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8801aeecb280 RCX: ffffffff8185ebd7
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00000000ffffffe1
RBP: ffff8801d907fc58 R08: ffff8801adb5e1c0 R09: ffffed0035a84700
R10: ffffed0035a84700 R11: ffff8801ad423803 R12: ffff8801aeecb280
R13: 00000000fffffff4 R14: ffff8801ad891a00 R15: 00000000014200c0
__do_kmalloc mm/slab.c:3713 [inline]
__kmalloc+0x25/0x760 mm/slab.c:3727
kmalloc include/linux/slab.h:517 [inline]
map_get_next_key+0x24a/0x640 kernel/bpf/syscall.c:858
__do_sys_bpf kernel/bpf/syscall.c:2131 [inline]
__se_sys_bpf kernel/bpf/syscall.c:2096 [inline]
__x64_sys_bpf+0x354/0x4f0 kernel/bpf/syscall.c:2096
do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The test case is against sock hashmap with a key size 0xffffffe1.
Such a large key size will cause the below code in function
sock_hash_alloc() overflowing and produces a smaller elem_size,
hence map creation will be successful.
htab->elem_size = sizeof(struct htab_elem) +
round_up(htab->map.key_size, 8);
Later, when map_get_next_key is called and kernel tries
to allocate the key unsuccessfully, it will issue
the above warning.
Similar to hashtab, ensure the key size is at most
MAX_BPF_STACK for a successful map creation.
Fixes: 8111038444 ("bpf: sockmap, add hash map support")
Reported-by: syzbot+e4566d29080e7f3460ff@syzkaller.appspotmail.com
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The inline keyword was not at the beginning of the function declarations.
Fix the following warnings triggered when using W=1:
kernel/time/clocksource.c:456:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
kernel/time/clocksource.c:457:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: https://lkml.kernel.org/r/20180516195943.31924-1-malat@debian.org
I noticed that there is a possibility that printk_safe_log_store() causes
kernel oops because "args" parameter is passed to vsnprintf() again when
atomic_cmpxchg() detected that we raced. Fix this by using va_copy().
Link: http://lkml.kernel.org/r/201805112002.GIF21216.OFVHFOMLJtQFSO@I-love.SAKURA.ne.jp
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: dvyukov@google.com
Cc: syzkaller@googlegroups.com
Cc: fengguang.wu@intel.com
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 42a0bb3f71 ("printk/nmi: generic solution for safe printk in NMI")
Cc: 4.7+ <stable@vger.kernel.org> # v4.7+
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Mathieu Desnoyers