Only a few files really need that platform header. When later splitting
omap_mmc_platform_data into omap_mmc and omap_mmc_hs, those files
declaring an hs mmc platform data will have to change the platform
include, which is a good sanity check.
Also removing omap242x_init_mmc, which is not used anywhere, checked
with grep.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In sprz318f.pdf "Usage Note 2.7" says that UARTs cannot acknowledge
idle requests in smartidle mode when configured for DMA operations.
This prevents L4 from going idle. So let's use manual idle mode
instead.
Otherwise systems using Sebastian's 8250 patches with DMA will
never enter deeper idle states because of the errata above.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit cc824534d4 ("ARM: OMAP2+: hwmod: Rearm wake-up interrupts
for DT when MUSB is idled") fixed issues with hung UART wake-up
events by calling _reconfigure_io_chain() when MUSB is connected
or disconnected.
As pointed out by Paul Walmsley, we may need to also call
_reconfigure_io_chain() in other cases, so it should be a separate
flag. Let's add HWMOD_RECONFIG_IO_CHAIN as suggested by Paul.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The fields are not used by the driver and will be removed from platform
data. Don't set them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The current entry prevents system from idling if
the hwmod is defined in the .dts file so let's
change the idlemodes.
Note that we probably don't have SYSC_HAS_EMUFREE
or SYSS_HAS_RESET_STATUS either. If we do, those
can be added later on.
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3 doesn't contain "l3_init_clkdm" clock domain. Use the
proper clock domains for USB Host and USB TLL modules.
Gets rid of the following warnings during boot
omap_hwmod: usb_host_hs: could not associate to clkdm l3_init_clkdm
omap_hwmod: usb_tll_hs: could not associate to clkdm l3_init_clkdm
Reported-by: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Fixes: de231388cb ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3")
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Partha Basak <parthab@india.ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use the proper clock name 'usbhost_120m_fck' instead of the
alias 'ehci_logic_fck'
Get rid of the 'ehci_logic_fck' alias from the OMAP3 hwmod data
as well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The IVA MMU is not functional when used through the hwmod and
omap_device layers. Add fixes to clockdomain and hwmod data
to have it functional. The hwmod changes are needed to enable
the clock, and the SWSUP change is needed to wakeup the domain
because the power domain is programmed to be in RET, and there
is no automatic power domain switching to ON.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CONFIG_OMAP_IOMMU_IVA2 was defined originally to avoid conflicting
usage by tidspbridge and other iommu users. The same can be achieved
by marking the DT node disabled, so remove this obsolete flag and
the corresponding hwmod data can be enabled.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: revise commit log]
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=kOrX
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13-rc/hwmod-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into debug-ll-and-ldp-backlight-fix
A few OMAP hwmod fixes for v3.13-rc. One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit
ec2c082 (ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ)
updated the way interrupts for OMAP2/3 devices are defined in the
HWMOD data structures to being an index plus a fixed offset (defined
by OMAP_INTC_START).
Couple of irqs in the OMAP2/3 hwmod data were misconfigured completely
as they were missing this OMAP_INTC_START relative offset. Add this
offset back to fix the incorrect irq data for the following modules:
OMAP2 - GPMC, RNG
OMAP3 - GPMC, ISP MMU & IVA MMU
Signed-off-by: Suman Anna <s-anna@ti.com>
Fixes: 7d7e1eba7e ("ARM: OMAP2+: Prepare for irqs.h removal")
Fixes: ec2c0825ca ("ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
Fixes: de231388cb ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds Synchronous Serial Interface (SSI) hwmod support for
OMAP34xx SoCs.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With commit '82702ea11ddfe0e43382e1fa5b66d807d8114916' "ARM: OMAP2+:
Fix serial init for device tree based booting" stubbing out
omap_serial_early_init() for Device tree based booting, there was a
crash observed on AM335x based devices when hwmod does a
_setup_reset() early at boot.
This was rootcaused to hwmod trying to reset console uart while
earlycon was using it. The way to tell hwmod not to do this is to
specify the HWMOD_INIT_NO_RESET flag, which were infact set by the
omap_serial_early_init() function by parsing the cmdline to identify
the console device.
Parsing the cmdline to identify the uart used by earlycon itself seems
broken as there is nothing preventing earlycon to use a different one.
This patch, instead, attempts to populate the requiste flags for hwmod
based on the CONFIG_DEBUG_OMAPxUARTy FLAGS. This gets rid of the need
for cmdline parsing in the DT as well as non-DT cases to identify the
uart used by earlycon.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Mark Jackson <mpfj-list@newflow.co.uk>
Reported-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
have these changes merged through arm-soc. As we proceed to untangle
the dependencies between platform code and driver code, the amount of
changes in this category is fortunately shrinking, for 3.11 we have
16 branches here and 101 non-merge changesets, the majority of which
are for the stedma40 dma engine driver used in the ux500 platform.
Cleaning up that code touches multiple subsystems, but gets rid
of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox
is an intermediate step and is still omap specific at the moment.
Patches exist to generalize the subsystem and add other drivers
with the same API, but those did not make it for 3.11.
Conflicts:
* In cpu-db8500.c results from the removal of the u8500_of_init_devices
function in combination with the split of u8500_auxdata_lookup.
* In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mJsI
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
All definitions in arch/arm/mach-omap2/dma.h are removed so it can be
removed now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Last remaining DMA channel definitions in arch/arm/mach-omap2/dma.h
are used only by omap_hwmod_2xxx_3xxx_ipblock_data.c and
omap_hwmod_3xxx_data.c. Remove them by using directly DMA channel number in
hwmod data and drop definitions with a following script:
egrep '#define [OMAP|AM35XX].*DMA' arch/arm/mach-omap2/dma.h | cut -f 1,3 \
| while read i; do \
DEF=`echo $i |cut -d ' ' -f 2`; \
CH=`echo $i |cut -d ' ' -f 3`; \
echo "removing" $DEF; \
sed -i "s/${DEF}/${CH}/" arch/arm/mach-omap2/omap_hwmod_*.c; \
sed -i "/${DEF}/d" arch/arm/mach-omap2/dma.h; \
done
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The different generations of OMAP2+ SoCs have almost the same
mailbox IP, but the IP has configurable parameters for number
of users (interrupts it can generate out towards processors)
and number of fifos (the base unidirectional h/w communication
channel). This data cannot be read from any registers, and so
has been added to the platform data.
This data together with the interrupt-type configuration can be
used in properly figuring out the number of registers to save
and restore in the OMAP mailbox driver code.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
The OMAP mailbox platform driver code has been cleaned up to
remove the dependencies with soc.h in preparation for moving
the mailbox code to drivers folder.
The code relied on cpu_is_xxx/soc_is_xxx macros previously to
pick the the right set of mailbox devices and register with the
mailbox driver. This data is now represented in a concise format
and moved to the respective omap_hwmod data files and published
to the driver through the platform data.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
OMAP UART IP needs software control for slave idle modes based on functional
state of the IP. i.e The IP slave idle settings should be set to 'noidle' when
being used and then put back to 'smart_idle' when unused. Currently this is
handled by the driver with function pointers implemented in platform code.
This however breaks in case of device tree because of missing idle handling
APIs.
Previous patches in this series added a flag HWMOD_SWSUP_SIDLE_ACTIVE which
takes care of the mentioned requirement. Hence add the flag for all UART IPs
to take advantage of feature supported by framework.
Subsequent patches removes the slave idle handling from driver code.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
information. Also enable few HW errata workarounds for omap4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bKnC
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren <tony@atomide.com>:
Changes needed for enabling SOC_BUS for the SoC revision
information. Also enable few HW errata workarounds for omap4.
* tag 'omap-for-v3.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (236 commits)
ARM: OMAP4: Enable fix for Cortex-A9 erratas
ARM: OMAP2+: Export SoC information to userspace
ARM: OMAP2+: SoC name and revision unification
ARM: OMAP2+: Move common part of late init into common function
Includes an update to Linux 3.9-rc6
Conflicts:
arch/arm/mach-omap2/cclock44xx_data.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert the device data for the OMAP3 AES crypto IP
from explicit platform_data to hwmod.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert the device data for the OMAP3 SHAM2 (SHA1/MD5) crypto IP
from explicit platform_data to hwmod.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: updated to use per-SoC registration lists for GP-only hwmods;
fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For some unknown reason, allowing hwmod to control MIDLEMODE causes
core_pwrdm to not hit idle states for musb in DM3730 at least.
I've verified that setting any MIDLEMODE value other than "force
standby" before enabling the device causes subsequent suspend
attempts to fail with core_pwrdm not entering idle states, even
if the driver is unloaded and "force standby" is restored before
suspend attempt. To recover from this, soft reset can be used, but
that's not suitable solution for suspend.
Keeping the register set at force standby (reset value) makes it work
and device still functions properly, as musb has driver-controlled
OTG_FORCESTDBY register that controls MSTANDBY signal.
Note that TI PSP kernels also have similar workarounds.
This patch also fixes HWMOD_SWSUP_MSTANDBY documentation to match the
actual flag name.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to Mark Greer, on OMAP AM3517/3505 chips, the EMAC is unable
to wake the ARM up from WFI:
http://www.spinics.net/lists/arm-kernel/msg174734.html
Further troubleshooting was unable to narrow the problem down. So we
don't have much choice other than to block WFI when the EMAC is active
with the HWMOD_BLOCK_WFI flag.
Based on Mark's original patch. We're removing the omap_device-based
pm_lats code, so a different approach was needed.
This third version contains some corrections thanks to Mark's review.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h2Qo
-----END PGP SIGNATURE-----
Merge tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+UN
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
Remaining patches to allow omap2+ to build with multiplatform
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
* tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_2420_data.c
arch/arm/mach-omap2/omap_hwmod_2430_data.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes fixed up in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP_I2C_FLAG_RESET_REGS_POSTIDLE is not used anymore
in the i2c driver. Remove the flag.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit [i2c: omap: use revision check for OMAP_I2C_FLAG_APPLY_ERRATA_I207]
uses the revision id instead of the flag. So the flag can be safely removed.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently OMAP2+ devices are using the function __omap_dm_timer_reset() to
configure the clock-activity, idle, wakeup-enable and auto-idle fields in the
timer OCP_CFG register. The name of the function is mis-leading because this
function does not actually perform a reset of the timer.
For OMAP2+ devices, HWMOD is responsible for reseting and configuring the
timer OCP_CFG register. Therefore, do not use __omap_dm_timer_reset() for
OMAP2+ devices and rely on HWMOD. Furthermore, some timer instances do not
have the fields clock-activity, wakeup-enable and auto-idle and so this
function could configure the OCP_CFG register incorrectly.
Currently HWMOD is not configuring the clock-activity field in the OCP_CFG
register for timers that have this field. Commit 0f0d080 (ARM: OMAP: DMTimer:
Use posted mode) configures the clock-activity field to keep the f-clk enabled
so that the wake-up capability is enabled. Therefore, add the appropriate flags
to the timer HWMOD structures to configure this field in the same way.
For OMAP2/3 devices all dmtimers have the clock-activity field, where as for
OMAP4 devices, only dmtimer 1, 2 and 10 have the clock-activity field.
Verified on OMAP2420 H4, OMAP3430 Beagle and OMAP4430 Panda that HWMOD is
configuring the dmtimer OCP_CFG register as expected for clock-events timer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP2/3 devices, the HWMOD data does not define a software reset status
field for the DMTIMERs. Therefore, when HWMOD performs a soft-reset of the
DMTIMER we don't check and wait for the reset to complete. For OMAP2/3 devices,
the software reset status for a DMTIMER can be read from bit 0 of the DMTIMER
TISTAT register (referred to as the SYSS register in HWMOD). Add the
appropriate HWMOD definitions so that HWMOD will check the software reset
status when performing a software reset of the DMTIMER.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Currently, the OMAP3 HWMOD data defines two TIOCP_CFG register structures
(referred to as the SYSC register in the HWMOD data) where timers 1, 2 and 10
use one of the defintions and the other timers use the other definition. For
OMAP3 devices the structure of the DMTIMER TIOCP_CFG register is the same for
all 12 instances of the DMTIMER. Please note that this is a difference between
OMAP3 and OMAP4 and could be the source of the confusion.
For OMAP3 devices, the DMTIMER TIOCP_CFG register has the fields,
clock-activity, emufree, idlemode, enwakeup, softreset and autoidle for all
12 timers. Therefore, remove one of the SYSC register definitions for the
DMTIMERs and ensure the appropriate register fields are defined for all
DMTIMERs.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For omap1, we'll keep mach/serial.h around for 8250.c hardware
workarounds. For omap2+, we no longer need mach/serial.h and
can make it local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to keep the device related things in the
common i2c.c as omap2+ is using hwmod. Split the code to
mach-omap1 and mach-omap2 parts and only leave common
code to plat-omap/i2c.c.
Note that as omap1 only has one i2c controller, we can
now remove the old device related macros.
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to omap1, some of the omap2+ dma channel definitions are
used by some drivers. For moving omap2+ dma channel definitions
to mach-omap2/, the used ones should be defined locally to driver.
Drivers can eliminate it using DT, platform data, or IORESOURCE_DMA
And moving omap2+ DMA channel definitions to mach-omap2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to remove this from plat for ARM common zImage
support.
Also remove includes not needed by the omap_hsmmc.c driver.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Venkatraman S <svenkatr@ti.com>
[tony@atomide.com: fold in removal of unused driver includes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Some OMAP fixes for the 3.7 merge window, fixing mismerges, branch
integration issues, and bugs after the arm-soc merges.
* tag 'omap-for-v3.7-rc1/fixes-hwmod-clock-signed-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
ARM: OMAP: omap3evm: fix new sparse warning
ARM: OMAP2+: hwmod data: Fix PMU interrupt definitions
ARM: am33xx: clk: Update clkdev table to add mcasp alias
This patch adds a missing hwmod entry for the HDQ/1-Wire module present
in the AM3505/17 CPUs.
This restores 1-Wire support to our AM3505 boards. We think it probably
stopped working with commit 96b1b29d37
ARM: OMAP2+: HDQ1W: use omap_device
Signed-off-by: Raphael Assenat <raph@8d.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit ec2c082
(ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ) updated the way
interrupts for OMAP2/3 devices are defined in the HWMOD data structures to
being an index plus a fixed offset (defined by OMAP_INTC_START). The definition
of the PMU interrupts on OMAP2/3 devices is missing the OMAP_INTC_START offset
and so this is causing the allocation of PMU interrupts to fail on OMAP2/3
devices. So add the offset to fix this.
This is patch is based upon Tony's master branch for OMAP.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Merge in the late Kirkwood branch with the OMAP late branch for upstream
submission.
Final contents described in shared tag.
Fixup remove/change conflicts in arch/arm/mach-omap2/devices.c and
drivers/spi/spi-omap2-mcspi.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
OMAP4460 and OMAP4470 devices have dedicated PMU interrupts and so add these
interrupts to the MPU HWMOD so we can use these for PMU events on these
devices. The PMU interrupts need to be the first interrupts in the array of
interrupts as the ARM PMU driver assumes this.
By using these dedicated interrupts we only need to enable the MPU and DEBUG
sub-systems for PMU to work. This is different to OMAP4430 that did not have
dedicated interrupts and required other power domains in addition to the DEBUG
sub-system to be enabled so we could route the PMU events to the CTI interrupts.
Hence, OMAP4460 and OMAP4470 devices can use the same list of HWMODs to create
the PMU device that is using by OMAP3.
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Andreas Fenkart