Use ACCESS_ONCE to reduce the number of redundant loads on uncached memory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ACCESS_ONCE to reduce the number of variable reloads on uncached memory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is no longer necessary for preparing mac80211 tx status
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use local variables to reduce the number of load/store operations on uncached
memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the slot time based on the mac80211 short slot vs long slot setting
instead of just forcing long slot for all CCK-enabled channels.
This slightly improves 802.11g mode performance in in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k uses 8 usec as a sifs time, extracted from the initvals, whereas the
standard requires a sifs time of 10. The difference originates from the fact
that the SIFS register has an offset of 2 usec.
Fix the SIFS time definition to use the standard value of 10 usec and subtract
2 usecs when writing the SIFS register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Subtract the difference in preamble duration (in usec) from the value
returned by ieee80211_generic_frame_duration.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During normal operation, minstrel was showing suspicious EWMA probabilities
exceeding 100%. It looks like the tx status reporting in ath5k was not
properly clearing the rate index for rates which were never attempted.
This is caused by uninitialized stale data in the on-stack tx status
information, which is reused when more frames are received.
To fix this, rely on ts->ts_final_idx to select the last attempted rate,
instead of checking whether ts->ts_rate is set.
Additionally, the conversion from the driver rate index back to the
mac80211 rate index can be dropped, as the mac80211 tx status will still
have the original rate index which was used to set up the descriptor.
Additionally, one more inaccuracy was fixed - the final rate attempt
count only needs to be increased by one if the transmission attempt was
successful.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath5k driver does kmalloc allocations for pcal info in a loop.
But, if one fails it was simply returning -ENOMEM without freeing
already allocated memory. This patch corrects that oversight.
Reported-by: Eugene A. Shatokhin <dame_eugene@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Older versions have not been sold and the driver does not explicitly
check for them anyway, so we can simply ignore the macRev here.
Reduces ath9k_hw size on mips by more than 2 KB.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: configure beacons based on hw opmode" introduced
a regression which leads to kernel panic. Failed to stop ani timer
during the driver unload while any of the beaconing vif is running.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update Tx gain 23 for all tx gain table.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export RSSI information from all the control and extension
channel chains to debugfs. Also add rx antenna information
to debugfs. This will be useful for debugging purpose.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rx should only be enabled after enough rx buffers have been given to the
hardware, however ath_rx_buf_link was calling ath9k_hw_rxena after every
single added buffer.
Fix this by calling ath9k_hw_rxena directly from the rx tasklet after
completion instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I can't find any valid reason for not setting the ATH9K_RX_FILTER_PSPOLL
flag on older hardware and neither the documentation nor the reference
code mention any reason for excluding older hardware here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.
The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.
The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function returns true if there is atleast one frame
in any one of the tx queues.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current ath9k code does not handle beacon timers on opmode
specific. One such example is that a STA beacon config overwrites
already configured AP vif's beacon timers during scan.
On multi station vif case, configure beacon timers beased
on primary vif selected. This also helps while moving back
to single STA vif from multi STA vifs, where the power save
is enabled and hw has to be reconfigured with proper
beacon and bssid/aid. Otherwise connection poll will be triggered
so frequently due to beacon loss.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now bssid/aid is overridden with recently changed vif's
bss config. This may cause improper beacon updation due to
bssid/aid mismatch. On station mode, select an associated
sta vif as primary vif and configure that vif's bss into hw.
Update the primary vif on interface change and bss info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused bssid from ath_vif and set av_bslot on beacon
alloc/return.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The present check denies the IBSS interface addtion if we
already have any other vifs. But it fails to deny interface
addition if IBSS was already present.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the beacon timers are global, the individual vif type should not
be used to determine the beacon timer configuration mode, use the
global opmode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent cleanups in the beacon code fixed SWBA backoff calculation,
however it did not remove a line of code that worked around the issues
from the earlier version of the code.
After the cleanup, the initial TSF based slot calculation now always
returns 0 instead of ATH_BCBUF-1, so the previous hack that reversed the
slot order needs to be removed, as ad-hoc mode does not use staggered
beacons.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Culler reported a problem with his AR9170 device:
> ath: EEPROM regdomain: 0x5c
> ath: EEPROM indicates we should expect a direct regpair map
> ath: invalid regulatory domain/country code 0x5c
> ath: Invalid EEPROM contents
It turned out that the regdomain 'APL7_FCCA' was not mapped yet.
According to Luis R. Rodriguez [Atheros' engineer] APL7 maps to
FCC_CTL and FCCA maps to FCC_CTL as well, so the attached patch
should be correct.
Cc: <stable@kernel.org>
Reported-by: Joe Culler <joe.culler@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is nowhere used.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This does not seems to be used anywhere so remove it.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The phy information print during driver init time doesn't show
the numeric part of the chip name properly for AR9485. This patch
addresses this issue by adding the string to the respective array.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has the same purpose (and value) as ah->config.max_txtrig_level
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the number of tx queue, the number of keycache entries depends
on the chip and shouldn't be messed with based on EEPROM data.
Remove this field and stick to using AR_KEYTABLE_SIZE
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only used in one place, and the device id check that it's based on
can be moved there as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM contains a field that can restrict the number of hardware queues,
however this is not only useless (all the known chips contain the same
number of hardware queues), but also potentially dangerous in case of a
misprogrammed EEPROM (could trigger driver crashes), so let's just ignore
it completely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RF_BANK_SETUP, REG_WRITE_RF_ARRAY and REG_WRITE_ARRAY are way too big,
so they shouldn't be inlined at every single callsite, especially since they
can easily be turned into real functions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's easier to read and it slightly decreases code size
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the number of calls to register ops. On MIPS this reduces the
ath9k_hw binary size from 321k down to 310k
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this change, loading the address to a register read/write function
costs only one pointer dereference instead of two. On MIPS this reduces
ath9k_hw binary size from 326k down to 321k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for using RSN IBSS with ath9k. For now, this uses software
crypto for group addressed frames in RSN IBSS, but that may be
optimized in the future by extending the key cache design to support
per-STA RX GTK.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stuck beacon detection is supposed to trigger when 9 consecutive beacons
could not be sent by the hardware. When the driver runs only one active
AP mode interface, it still configures the hardware beacon timer for
4 (ATH_BCBUF) beacon slots slots, which causes stuck beacon detection
to be reset if ath9k_hw_stoptxdma clears the stuck frames between
SWBA intervals.
Fix this by not resetting the missed beacon count for empty slots and
multiplying the threshold not by the maximum number of beacon slots
but by the configured number of beacon interfaces.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Single missed (i.e. not transmitted) beacons in AP mode are not very rare
and not necessarily an indicator of strong interference, so only trigger
noise floor recalibration when multiple consecutive beacons could not
be transmitted.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP mode beacon timers in ath9k are configured in milliseconds, which breaks
when increasing ATH_BCBUF to 8 instead of 4 (due to rounding errors).
Since the hardware timers are actually configured in microseconds, it's
better to let the driver use that unit directly.
To be able to do that, the beacon interval parameter abuse for passing
certain flags needs to be removed. This is easy to do, because those flags
are completely unnecessary anyway. ATH9K_BEACON_ENA is ignored,
ATH9K_BEACON_RESET_TSF can be replaced with calling ath9k_hw_reset_tsf
from the driver directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only AR9485 1.1 was sold. This debloats the driver by ~14 KiB.
text data bss dec hex filename
300413 624 1056 302093 49c0d drivers/net/wireless/ath/ath9k/ath9k_hw.ko
text data bss dec hex filename
310285 624 1056 311965 4c29d drivers/net/wireless/ath/ath9k/ath9k_hw-old.ko
$ du -b ath9k_hw*
6210541 ath9k_hw.ko
6225089 ath9k_hw-old.ko
Cc: Bill Wu <bill.wu@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Forbes Tsai <Forbes.Tsai@Atheros.com>
Cc: Jesmine Chen <jesmine.chen@atheros.com>
Cc: Marvian Chen <Hou-hua.Chen@Atheros.com>
Cc: Vivek Natarajan <vivek.natarajan@atheros.com>
Cc: Bernadette Yetso <bernadette.yetso@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Acked-by: Yi-Chen Su <yi-chen.su@atheros.com>
Acked-by: Jeffrey Chung <jeffrey.chung@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This workaround called ath_txq_schedule whenever there were still pending
frames for a queue, but the queue depth was zero. Because of its its high
false positive probability (e.g. with paused TIDs) and because it is in
the way of other pending work (AP powersave fixes), it is better to remove
this code entirely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most AR9100 devices already have a chainmask of 7 (three antennas), however
on the ones that don't (rx and tx chainmask set to 5), problems with IQ
mismatch calibration have been observed.
This shows up as tx queue hangs (and subsequent hardware resets) if traffic
is sent during this type of calibration.
Forcing the rx chainmask to 7 fixes the calibration issues with no apparent
negative side effects on throughput and stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes interop issues with aggregation in combination with multi-BSSID
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some devices the correct MAC address is not in the EEPROM data, but
stored somewhere else.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices control antenna settings or other things through GPIO pins
of the wireless interface. Add a debugfs interface for changing those
and keeping them set across card resets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the ath9k debugfs directory is cleaned up by debugfs_remove_recursive,
there's no point in checking the return code of every single debugfs create
line.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fine-tuning register write operation and avoid unnecessay
delays for ath9k_htc driver, saves hw reset time which
improves scanning time and also solves one of the following
scenario.
Sometimes the ACK is sent by STA for assoc response is not
seen at AP side. So the AP continues to send retry assoc
responses. At the STA side, since the assoc response was
already forwarded to mac80211, it proceeded to channel change
which in turns does chip reset.
In most of the cases the chip reset was completed before
max retries are reached at AP side. Hence STA can able to ACK
the retried frames again. But in clear environment these retries
are completed within shortspan of time.
Since ath9k_htc consumes more time for hw reset, this latency
is causing dissociation by AP due to max reties are reached.
This issue was originally reported with Cisco Aironet 1250 AP
in HT40 mode in noise free environment.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By enabling buffered register write for ath9k_htc driver
avoids unnecessary dissociation while rekeying phase under
heavy traffic exchange.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing adc gain calibration for AR9287 chips is causing
throughput drops in HT40 mode. Remove ADC Gain from supported
calibration list.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some clients seem to rely upon the reception of BlockAckReqs to flush
their rx reorder buffer. In order to fix aggregation for these clients
carl9170 should set IEEE80211_TX_STAT_AMPDU_NO_BACK to generate a
BlockAckReq if the transmission of an AMPDU subframe fails.
This fixes aggregation problems with Intel 5100 Windows STAs (and maybe
others as well).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is still asleep when ath9k_start is called,
ath9k_hw_configpcipowersave can trigger a data bus error.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 86271e460a introduced a
regression that caused mac80211 queues in stopped state.
ath_drain_all_txq is called in driver flush which would reset
the stopped flag and the mac80211 queues were never started
after that. iperf traffic is completely stalled due to this issue.
Restart the mac80211 queues in driver flush only if the txqs were
drained.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the recent tx status optimization in mac80211, we bail out as
and and when invalid rate index is found. So the behavior of resetting
rate idx to -1 and count to 0 has changed for the rate indexes that
were not part of the driver's retry series.
This has resulted in ath9k using incorrect rate table index which
caused the system to panic. Ideally ath9k need to loop only for the
indexes that were part of the retry series and so simply use hw->max_rates
as the loop counter.
Pasted the stack trace of the panic issue for reference.
[ 754.093192] BUG: unable to handle kernel paging request at ffff88046a9025b0
[ 754.093256] IP: [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
[ 754.094888] Call Trace:
[ 754.094903] <IRQ>
[ 754.094928] [<ffffffffa051f883>] ieee80211_tx_status+0x203/0x9e0 [mac80211]
[ 754.094975] [<ffffffffa053e305>] ? __ieee80211_wake_queue+0x125/0x140 [mac80211]
[ 754.095017] [<ffffffffa02e66c9>] ath_tx_complete_buf+0x1b9/0x370 [ath9k]
[ 754.095054] [<ffffffffa02e6fcf>] ath_tx_complete_aggr+0x51f/0xb50 [ath9k]
[ 754.095098] [<ffffffffa05382a3>] ? ieee80211_prepare_and_rx_handle+0x173/0xab0 [mac80211]
[ 754.095148] [<ffffffff81350e62>] ? _raw_spin_unlock_irqrestore+0x32/0x40
[ 754.095186] [<ffffffffa02e9735>] ath_tx_tasklet+0x365/0x4b0 [ath9k]
[ 754.095224] [<ffffffff8107a2a2>] ? clockevents_program_event+0x62/0xa0
[ 754.095261] [<ffffffffa02e2628>] ath9k_tasklet+0x168/0x1c0 [ath9k]
[ 754.095298] [<ffffffff8105599b>] tasklet_action+0x6b/0xe0
[ 754.095331] [<ffffffff81056278>] __do_softirq+0x98/0x120
[ 754.095361] [<ffffffff8100cd5c>] call_softirq+0x1c/0x30
[ 754.095393] [<ffffffff8100efb5>] do_softirq+0x65/0xa0
[ 754.095423] [<ffffffff810563fd>] irq_exit+0x8d/0x90
[ 754.095453] [<ffffffff8100ebc1>] do_IRQ+0x61/0xe0
[ 754.095482] [<ffffffff81351413>] ret_from_intr+0x0/0x15
[ 754.095513] <EOI>
[ 754.095531] [<ffffffff81014375>] ? native_sched_clock+0x15/0x70
[ 754.096475] [<ffffffffa02bcfa6>] ? acpi_idle_enter_bm+0x24d/0x285 [processor]
[ 754.096475] [<ffffffffa02bcf9f>] ? acpi_idle_enter_bm+0x246/0x285 [processor]
[ 754.096475] [<ffffffff8127fab2>] cpuidle_idle_call+0x82/0x100
[ 754.096475] [<ffffffff8100a236>] cpu_idle+0xa6/0xf0
[ 754.096475] [<ffffffff81339bc1>] rest_init+0x91/0xa0
[ 754.096475] [<ffffffff814efccd>] start_kernel+0x3fd/0x408
[ 754.096475] [<ffffffff814ef347>] x86_64_start_reservations+0x132/0x136
[ 754.096475] [<ffffffff814ef451>] x86_64_start_kernel+0x106/0x115
[ 754.096475] RIP [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some clients seems to keep track of their reorder window even after an
aggregation session has been disabled. This causes issues if there are
still retried but not completed frames pending for the TID.
To ensure that rx does not stall in such situations, set sendbar to 1
for any frame purged from the TID queue on teardown.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k calls ath9k_hw_stoptxdma every time it sends a beacon, however there
is not much point in doing that if the previous beacon and mcast traffic
went out properly. On AR9380, calling that function too often can result
in an increase of stuck beacons due to differences in the handling of the
queue enable/disable functionality.
With this patch, the queue will only be explicitly stopped if the previous
data frames were not sent successfully. With the beacon code being the
only remaining user of ath9k_hw_stoptxdma, this function can be simplified
in order to remove the now pointless attempts at waiting for transmission
completion, which would never happen at this point due to the different
method of tx scheduling of the beacon queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the flush op and reuses ath_drain_all_txq for
flushing out pending frames if necessary. It also uses a global timeout
of 200ms instead of the per-queue 60ms timeout.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations, stopping Tx DMA frequently fails, leading to messages
like this:
ath: Failed to stop TX DMA in 100 msec after killing last frame
ath: Failed to stop TX DMA!
This patch uses a few MAC features to abort DMA globally instead of iterating
over all hardware queues and attempting to stop them individually.
Not only is that faster and works with a shorter timeout, it also makes the
process much more reliable.
With this change, I can no longer trigger these messages on AR9380,
and on AR9280 they become much more rare.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increasing the wait count makes the nf load pass in
most of the cases.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase the delay to make sure the initialization of pll
passes.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set some GPIO pins to Pull-down mode to save power.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware rx filter flag triggered by FIF_PROMISC_IN_BSS is overly broad
and covers even frames with PHY errors. When this flag is enabled, this message
shows up frequently during scanning or hardware resets:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
Since promiscuous mode is usually not particularly useful, yet enabled by
default by bridging (either used normally in 4-addr mode, or with hacks
for various virtualization software), we should sacrifice it for better
reliability during normal operation.
This patch leaves it enabled if there are active monitor mode interfaces, since
it's very useful for debugging.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems ath5k has issues receiving broadcast packets (ARPs) when
using multiple STA interfaces associated with multiple APs.
This patch ensures the NIC is always in PROMISC mode if there
are more than 1 stations associated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No use printing addresses of pointers, just print the
pointers themselves.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
/<debugfs_root>/ieee80211/phyX/ath9k/regdump is the interface
to dump the registers.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AID and BSSID should be set in the HW only for the
first station interface or adhoc interface. Also, cancel
the ANI timer in stop() for multi-STA scenario. And finally
configure the HW beacon timers only for the first station
interface.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485 doesn't use the default GPIO pin for LED and GPIO 6 is actually
used for this.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stream length/tag fields have to be in little endian
format. Fixing this makes the driver work on big-endian
platforms.
Cc: stable@kernel.org
Tested-by: raghunathan.kailasanathan@wipro.com
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize txq to avoid this warning:
drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_flush’:
drivers/net/wireless/ath/ath9k/main.c:2138: warning: ‘txq’ may be used uninitialized in this function
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pll_work should be cancelled on full_sleep or it may cause
redundant chip reset.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).
Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.
Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"AirLive X.USB now works perfectly under a Linux
environment!"
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 4df3071ebd "ath9k_hw: optimize
interrupt mask changes", changed ath9k_hw_set_interrupts function to
enable interrupts regardless of function argument, what could possibly
be wrong. Correct that behaviour and check "ints" arguments before
enabling interrupts, also disable interrupts if ints do not have
ATH9K_INT_GLOBAL flag set.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag isn't very descriptive -- the intention
is that the driver provides a TSF timestamp at
the beginning of the MPDU -- make that clearer
by renaming the flag to RX_FLAG_MACTIME_MPDU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hif_usb_alloc_urbs() takes care of freeing
all the allocated URBs for the various endpoints when
an error occurs. Calling ath9k_hif_usb_dealloc_urbs() would
cause a panic since the URBs have already been freed.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ATH9K_RX_FILTER_UNCOMP_BA_BAR and ATH9K_RX_FILTER_PSPOLL
when mac80211 requires it.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to set the BSSID mask or opmode when
initializing RX, they would be set correctly in the HW reset
routine.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The target beacon transmission time has to be synced with the HW
TSF when configuring beacon timers in Adhoc mode. Failing to do this
would cause erroneous beacon transmission, for example, on completion
of a scan run to check for IBSS merges.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle multi-interface situations by checking if
AP interfaces are already present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau