Set and report vport MTU rather than physical MTU,
Driver will set both vport and physical port mtu and will
rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For set/query MTU port firmware commands the MTU field
is 16 bits, here I changed all the "int mtu" parameters
of the functions wrapping those firmware commands to be u16.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the feature of multi-packet WQE (RX Work Queue Element)
referred to as (MPWQE or Striding RQ), in which WQEs are larger
and serve multiple packets each.
Every WQE consists of many strides of the same size, every received
packet is aligned to a beginning of a stride and is written to
consecutive strides within a WQE.
In the regular approach, each regular WQE is big enough to be capable
of serving one received packet of any size up to MTU or 64K in case of
device LRO is enabled, making it very wasteful when dealing with
small packets or device LRO is enabled.
For its flexibility, MPWQE allows a better memory utilization
(implying improvements in CPU utilization and packet rate) as packets
consume strides according to their size, preserving the rest of
the WQE to be available for other packets.
MPWQE default configuration:
Num of WQEs = 16
Strides Per WQE = 2048
Stride Size = 64 byte
The default WQEs memory footprint went from 1024*mtu (~1.5MB) to
16 * 2048 * 64 = 2MB per ring.
However, HW LRO can now be supported at no additional cost in memory
footprint, and hence we turn it on by default and get an even better
performance.
Performance tested on ConnectX4-Lx 50G.
To isolate the feature under test, the numbers below were measured with
HW LRO turned off. We verified that the performance just improves when
LRO is turned back on.
* Netperf single TCP stream:
- BW raised by 10-15% for representative packet sizes:
default, 64B, 1024B, 1478B, 65536B.
* Netperf multi TCP stream:
- No degradation, line rate reached.
* Pktgen: packet rate raised by 2-10% for traffic of different message
sizes: 64B, 128B, 256B, 1024B, and 1500B.
* Pktgen: packet loss in bursts of small messages (64byte),
single stream:
- | num packets | packets loss before | packets loss after
| 2K | ~ 1K | 0
| 8K | ~ 6K | 0
| 16K | ~13K | 0
| 32K | ~28K | 0
| 64K | ~57K | ~24K
As expected as the driver can receive as many small packets (<=64B) as
the number of total strides in the ring (default = 2048 * 16) vs. 1024
(default ring size regardless of packets size) before this feature.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A queue counter can collect several statistics for one or more
hardware queues (QPs, RQs, etc ..) that the counter is attached to.
For Ethernet it will provide an "out of buffer" counter which
collects the number of all packets that are dropped due to lack
of software buffers.
Here we add device commands to alloc/query/dealloc queue counters.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the needed mlx5_ifc hardware bits and structs
for the following feature:
* Add vport to steering commands for SRIOV ACL support
* Add mlcr, pcmr and mcia registers for dump module EEPROM
* Add support for FCS, baeacon led and disable_link bits to
hca caps
* Add CQE period mode bit in CQ context for CQE based CQ
moderation support
* Add umr SQ bit for fragmented memory registration
* Add needed bits and caps for Striding RQ support
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All reserved fields after early_vf_enable are off by 1, since
early_vf_enable was not explicitly declared as array of size 1.
Reserved field before cqe_zip had a wrong size, it should
be 0x80 + 0x3f.
Fixes: b084444459 ("net/mlx5_core: Introduce access function to read internal timer ")
Fixes: b4ff3a36d3 ("net/mlx5: Use offset based reserved field names in the IFC header file")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects
the net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular interest
here is that we have left the driver in staging since it still has an
API that people object to. Intel is working on a fix, but getting
these patches in now helps keep me sane as the upstream and Intel's
trees were over 300 patches apart.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t2Ko
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"Round two of 4.6 merge window patches.
This is a monster pull request. I held off on the hfi1 driver updates
(the hfi1 driver is intimately tied to the qib driver and the new
rdmavt software library that was created to help both of them) in my
first pull request. The hfi1/qib/rdmavt update is probably 90% of
this pull request. The hfi1 driver is being left in staging so that
it can be fixed up in regards to the API that Al and yourself didn't
like. Intel has agreed to do the work, but in the meantime, this
clears out 300+ patches in the backlog queue and brings my tree and
their tree closer to sync.
This also includes about 10 patches to the core and a few to mlx5 to
create an infrastructure for configuring SRIOV ports on IB devices.
That series includes one patch to the net core that we sent to netdev@
and Dave Miller with each of the three revisions to the series. We
didn't get any response to the patch, so we took that as implicit
approval.
Finally, this series includes Intel's new iWARP driver for their x722
cards. It's not nearly the beast as the hfi1 driver. It also has a
linux-next merge issue, but that has been resolved and it now passes
just fine.
Summary:
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects the
net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular
interest here is that we have left the driver in staging since it
still has an API that people object to. Intel is working on a fix,
but getting these patches in now helps keep me sane as the upstream
and Intel's trees were over 300 patches apart"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (362 commits)
IB/ipoib: Allow mcast packets from other VFs
IB/mlx5: Implement callbacks for manipulating VFs
net/mlx5_core: Implement modify HCA vport command
net/mlx5_core: Add VF param when querying vport counter
IB/ipoib: Add ndo operations for configuring VFs
IB/core: Add interfaces to control VF attributes
IB/core: Support accessing SA in virtualized environment
IB/core: Add subnet prefix to port info
IB/mlx5: Fix decision on using MAD_IFC
net/core: Add support for configuring VF GUIDs
IB/{core, ulp} Support above 32 possible device capability flags
IB/core: Replace setting the zero values in ib_uverbs_ex_query_device
net/mlx5_core: Introduce offload arithmetic hardware capabilities
net/mlx5_core: Refactor device capability function
net/mlx5_core: Fix caching ATOMIC endian mode capability
ib_srpt: fix a WARN_ON() message
i40iw: Replace the obsolete crypto hash interface with shash
IB/hfi1: Add SDMA cache eviction algorithm
IB/hfi1: Switch to using the pin query function
IB/hfi1: Specify mm when releasing pages
...
Implement the IB defined callbacks used to manipulate the policy for the
link state, set GUIDs or get statistics information. This functionality
is added into a new file that will be used to add any SRIOV related
functionality to the mlx5 IB layer.
The following callbacks have been added:
mlx5_ib_get_vf_config
mlx5_ib_set_vf_link_state
mlx5_ib_get_vf_stats
mlx5_ib_set_vf_guid
In addition, publish whether this device is based on a virtual function.
In mlx5 supported devices, virtual functions are implemented as vHCAs.
vHCAs have their own QP number space so it is possible that two vHCAs
will use a QP with the same number at the same time.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implement the modify HCA vport commands used to modify the parameters of
virtual HCA's ports.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a vf parameter to mlx5_core_query_vport_counter so we can call it to
query counters of virtual functions. Also update current users of the
API.
PFs may call mlx5_core_query_vport_counter with other_vport set to
indicate that they are querying a virtual function. The virtual
function to be queried is given by the vf parameter. Virtual function
numbering is zero based so the first VF is 0 and so on. When a PF
queries its own function, the other_vport parameter is cleared.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Define the necessary hardware structures for the offload
arithmetic capabilities and read/cache them on driver load.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Device capability function was called similar in all places.
It was called twice for every queried parameter, while the
difference between calls was in HCA capability mode only.
The change proposed unify these calls into one function.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
- cxgb4 updates
- nes updates
- unification of iwarp portmapper code to core
- add drain_cq API
- various ib_core updates
- minor ipoib updates
- minor mlx4 updates
- more significant mlx5 updates (including a minor merge conflict with
net-next tree...merge is simple to resolve and Stephen's resolution was
confirmed by Mellanox)
- trivial net/9p rdma conversion
- ocrdma RoCEv2 update
- srpt updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kTkT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.6 merge window patches.
This is the first of two pull requests. It is the smaller request,
but touches for more different things (this is everything but what is
in or going into staging). The pull request for the code in
staging/rdma is on hold until after we decide what to do on the
write/writev API issue and may be partially deferred until 4.7 as a
result.
Summary:
- cxgb4 updates
- nes updates
- unification of iwarp portmapper code to core
- add drain_cq API
- various ib_core updates
- minor ipoib updates
- minor mlx4 updates
- more significant mlx5 updates (including a minor merge conflict
with net-next tree...merge is simple to resolve and Stephen's
resolution was confirmed by Mellanox)
- trivial net/9p rdma conversion
- ocrdma RoCEv2 update
- srpt updates"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (85 commits)
iwpm: crash fix for large connections test
iw_cxgb3: support for iWARP port mapping
iw_cxgb4: remove port mapper related code
iw_nes: remove port mapper related code
iwcm: common code for port mapper
net/9p: convert to new CQ API
IB/mlx5: Add support for don't trap rules
net/mlx5_core: Introduce forward to next priority action
net/mlx5_core: Create anchor of last flow table
iser: Accept arbitrary sg lists mapping if the device supports it
mlx5: Add arbitrary sg list support
IB/core: Add arbitrary sg_list support
IB/mlx5: Expose correct max_fast_reg_page_list_len
IB/mlx5: Make coding style more consistent
IB/mlx5: Convert UMR CQ to new CQ API
IB/ocrdma: Skip using unneeded intermediate variable
IB/ocrdma: Skip using unneeded intermediate variable
IB/ocrdma: Delete unnecessary variable initialisations in 11 functions
IB/core: Documentation fix in the MAD header file
IB/core: trivial prink cleanup.
...
Each bypass flow steering priority will be split into two priorities:
1. Priority for don't trap rules.
2. Priority for normal rules.
When user creates a flow using IB_FLOW_ATTR_FLAGS_DONT_TRAP flag, the
driver creates two flow rules, one used for receiving the traffic and
the other one for forwarding the packet to continue matching in lower
or equal priorities.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support to create flow rule that forward packets
to the first flow table in the next priority (next priority
could be the first priority in the next namespace or the
next priority in the same namespace).
This feature could be used for DONT_TRAP rules or rules
that only want to mark the packet with flow tag.
In order to do it optimally, each flow table has list
of all rules that point to this flow table,
when a flow table is destroyed/created, we update the list
head correspondingly.
This kind of rule is created when destination is NULL and
action is MLX5_FLOW_CONTEXT_ACTION_FWD_NEXT_PRIO.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Create an empty flow table in the end of NIC rx namesapce.
Adding this flow table simplify the implementation of "forward
to next prio" rules.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should modify TIRs explicitly to apply the new RSS configuration.
The light ndo close/open calls do not "refresh" them.
Fixes: 2d75b2bc8a ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid double mapping of io mapped memory, Device page may be
mapped to non-cached(NC) or to write-combining(WC).
The code before this fix tries to map it both to WC and NC
contrary to what stated in Intel's software developer manual.
Here we remove the global WC mapping of all UARS
"dev->priv.bf_mapping", since UAR mapping should be decided
per UAR (e.g we want different mappings for EQs, CQs vs QPs).
Caller will now have to choose whether to map via
write-combining API or not.
mlx5e SQs will choose write-combining in order to perform
BlueFlame writes.
Fixes: 88a85f99e5 ('TX latency optimization to save DMA reads')
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Reviewed-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The command timeout is terribly long, whole two hours. Make it 60s so if
things do go wrong, the user gets feedback in relatively short time, so
they can take corrective actions and/or investigate using tools and such.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds user-space support for memory windows allocation and
deallocation. It also exposes the supported types via
query_device_caps verb.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Tested-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Mlx5's mkey mechanism is also used for memory windows.
The current code base uses MR (memory region) naming, which is
inaccurate. Changing MR to mkey in order to represent its different
usages more accurately.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to create multiple GSI QPs, we need to set the source QP number to
one on all these QPs. Add the necessary definitions and infrastructure to
do that.
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The HW can supply several offloads for UD QP, added offloads for
checksumming for both TX and RX and LSO for TX.
Two new bits were added in order to expose and enable these offloads:
1. HCA capability bit: declares the support for IPoIB basic offloads.
2. QPC bit which will be used in the QP creation flow, which set these
abilities in the QP.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Modify mlx5_ib_process_mad to use PPCNT and query_vport commands
instead of MAD_IFC, as MAD_IFC is deprecated on new firmware
versions (and doesn't support RoCE anyway).
Traffic counters exist in both 32-bit and 64-bit forms.
Declaring support of extended coutners results in traffic counters
to be read in their 64-bit form only via the query_vport command.
Error counters exist only in 32-bit form and read via PPCNT command.
This commit also adds counters support in RoCE.
Signed-off-by: Meny Yossefi <menyy@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Added helper function to read IB standard error counters
via the PPCNT register.
The PPCNT register read command provides the 32-bit error counters
of both IB/RoCE link layer and transport layer.
Signed-off-by: Meny Yossefi <menyy@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implement set/get WOL by ethtool and added the needed
device commands and structures to mlx5_ifc.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DCBNL IEEE get/set max rate.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access functions to set and query a physical port TC groups
and prio parameters.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access functions to set and query a physical port PFC
(Priority Flow Control) parameters.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the device physical port access functions are implemented in the
port.c file.
We just extract the exposure of these functions from driver.h into a
dedicated header file called port.h.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_ifc.h is a header file representing the API and ABI between
the driver to the firmware and hardware. This file is used from
both the mlx5_ib and mlx5_core drivers.
Previously, this file used incrementing counter to indicate
reserved fields, for example:
struct mlx5_ifc_odp_per_transport_service_cap_bits {
u8 send[0x1];
u8 receive[0x1];
u8 write[0x1];
u8 read[0x1];
u8 reserved_0[0x1];
u8 srq_receive[0x1];
u8 reserved_1[0x1a];
};
If one developer implements through net-next feature A that uses
reserved_0, they replace it with featureA and renames reserved_1 to
reserved_0. In the same kernel cycle, a 2nd developer could implement
feature B through the rdma tree, that uses reserved_1 and split it to
featureB and a smaller reserved_1 field. This will cause a conflict
when the two trees are merged.
The source of this conflict is that the 1st developer changed *all*
reserved fields.
As Linus suggested, we change the layout of structs to:
struct mlx5_ifc_odp_per_transport_service_cap_bits {
u8 send[0x1];
u8 receive[0x1];
u8 write[0x1];
u8 read[0x1];
u8 reserved_at_4[0x1];
u8 srq_receive[0x1];
u8 reserved_at_6[0x1a];
};
This makes the conflicts much more rare and preserves the locality of
changes.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed through the
RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to dependencies,
acknowledged by Bruce)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5oO7
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.5 merge window patches
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed
through the RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to
dependencies, acknowledged by Bruce)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (169 commits)
IB/mlx5: Unify CQ create flags check
IB/mlx5: Expose Raw Packet QP to user space consumers
{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib
IB/mlx5: Support setting Ethernet priority for Raw Packet QPs
IB/mlx5: Add Raw Packet QP query functionality
IB/mlx5: Add create and destroy functionality for Raw Packet QP
IB/mlx5: Refactor mlx5_ib_qp to accommodate other QP types
IB/mlx5: Allocate a Transport Domain for each ucontext
net/mlx5_core: Warn on unsupported events of QP/RQ/SQ
net/mlx5_core: Add RQ and SQ event handling
net/mlx5_core: Export transport objects
IB/mlx5: Expose CQE version to user-space
IB/mlx5: Add CQE version 1 support to user QPs and SRQs
IB/mlx5: Fix data validation in mlx5_ib_alloc_ucontext
IB/sa: Fix netlink local service GFP crash
IB/srpt: Remove redundant wc array
IB/qib: Improve ipoib UD performance
IB/mlx4: Advertise RoCE v2 support
IB/mlx4: Create and use another QP1 for RoCEv2
IB/mlx4: Enable send of RoCE QP1 packets with IP/UDP headers
...
When modifying a QP, the desired operation was determined in
the mlx5_core using a transition table that takes the current
state, the final state, and returns the desired operation.
Since this logic will be used for Raw Packet QP, move the
operation table to the mlx5_ib.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When the user changes the Address Vector(AV) in the modify QP, he
provides an SL. This SL should be translated to Ethernet Priority
by taking the 3 LSB bits, and modify the QP's TIS according to this
Ethernet priority.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since Raw Packet QP is composed of RQ and SQ, the IB QP's
state is derived from the sub-objects. Therefore we need
to query each one of the sub-objects, and decide on the
IB QP's state.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RQ/SQ will be used to implement IB verbs QPs, so the IB QP affiliated
events are affiliated also with SQs and RQs.
Since SQ, RQ and QP resource numbers do not share the same name
space, a queue type field was added to the event data to specify
the SW object that the event is affiliated with.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To be used by mlx5_ib in the following patches for implementing
RAW PACKET QP.
Add mlx5_core_ prefix to alloc and delloc transport_domain since
they are exposed now.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
With several ConnectX-4 cards installed on a server, one may receive
irqn > 255 from the kernel API, which we mistakenly trim to 8bit.
This causes EQ creation failure with the following stack trace:
[<ffffffff812a11f4>] dump_stack+0x48/0x64
[<ffffffff810ace21>] __setup_irq+0x3a1/0x4f0
[<ffffffff810ad7e0>] request_threaded_irq+0x120/0x180
[<ffffffffa0923660>] ? mlx5_eq_int+0x450/0x450 [mlx5_core]
[<ffffffffa0922f64>] mlx5_create_map_eq+0x1e4/0x2b0 [mlx5_core]
[<ffffffffa091de01>] alloc_comp_eqs+0xb1/0x180 [mlx5_core]
[<ffffffffa091ea99>] mlx5_dev_init+0x5e9/0x6e0 [mlx5_core]
[<ffffffffa091ec29>] init_one+0x99/0x1c0 [mlx5_core]
[<ffffffff812e2afc>] local_pci_probe+0x4c/0xa0
Fixing it by changing of the irqn type from u8 to unsigned int to
support values > 255
Fixes: 61d0e73e0a ('net/mlx5_core: Use the the real irqn in eq->irqn')
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding flow steering support by creating a flow-table per
priority (if rules exist in the priority). mlx5_ib uses
autogrouping and thus only creates the required destinations.
Also includes adding of these flow steering utilities
1. Parsing verbs flow attributes hardware steering specs.
2. Check if flow is multicast - this is required in order to decide
to which flow table will we add the steering rule.
3. Set outer headers in flow match criteria to zeros.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the mlx5 firmware interface header to make it
more clear which bytes should be used by IPv4 or
IPv6 addresses.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is loaded, we create flow steering namespace
for kernel bypass with nine priorities and another namespace
for leftovers(in order to catch packets that weren't matched).
Verbs applications will use these priorities.
we found nine as a number that balances the requirements from the
user and retains performance.
The bypass namespace is used by verbs applications that want to bypass
the kernel networking stack. The leftovers namespace is used by verbs
applications and the sniffer in order to catch packets that weren't
handled by any preceding rules.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the modify flow table command. This command is used when
we want to change the next flow table of an existing flow table.
The next flow table is defined as the table we search (in order
to find a match), if we couldn't find a match in any of the flow table
entries in the current flow table.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The root Flow Table for each Flow Table Type is defined,
by default, as the Flow Table with level 0.
In order not to use an empty flow tables and introduce new hops,
but still preserve space for flow-tables that have a priority
greater(lower number) than the current flow table, we introduce this
new set root flow table command.
This command tells the HW to start matching packets from the
assigned root flow table.
This command is used when we create new flow table with level lower than the
current lowest flow table or it is the first flow table.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user add rule to autogrouped flow table, we search
for flow group with the same match criteria, if we don't
find such group then we create new flow group with the
required match criteria and insert the rule to this group.
We divide the flow table into required_groups + 1,
in order to reserve a part of the flow table for rules
which don't match any existing group.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A preparation step which adds support for reading the hardware
internal timer and the hardware timestamping from the CQE.
In addition, advertize device_frequency_khz HCA capability.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to ensure IB spec atomic correctness in atomic operations, if
HW is configured to host endianness, advertise IB_ATOMIC_HCA. if not,
advertise IB_ATOMIC_NONE.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
HW is capable of 2 requestor endianness modes for standard 8 Bytes
atomic: BE (0x0) and host endianness (0x1). Read the supported modes
from hca atomic capabilities and configure HW to host endianness mode if
supported.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support of cross-channel functionality to mlx5
driver. This includes ability to ignore overrun for CQ
which intended for cross-channel, export device capability and
configure the QP to be sync master/slave queues.
The cross-channel enabled QP supports combination of
three possible properties:
* WQE processing on the receive queue of this QP
* WQE processing on the send queue of this QP
* WQE are supported on the send queue
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pass hca_core_clock_offset to user-space is mandatory in order to
let the user-space read the free-running clock register from the
right offset in the memory mapped page.
Passing this value is done by changing the vendor's command
and response of init_ucontext to be in extensible form.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reporting the hca_core_clock (in kHZ) and the timestamp_mask in
query_device extended verb. timestamp_mask is used by users in order
to know what is the valid range of the raw timestamps, while
hca_core_clock reports the clock frequency that is used for
timestamps.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the address handle and QP address path fields according to the
link layer type (IB/Eth).
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These callbacks write into the mlx5 RoCE address table.
Upon del_gid we write a zero'd GID.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When handling a responder completion, if the link layer is Ethernet,
set the work completion network_hdr_type field according to CQE's
info and the IB_WC_WITH_NETWORK_HDR_TYPE flag.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Using the vport access functions to retrieve the Ethernet
specific information and return this information in
ib_query_device and ib_query_port.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A mlx5 Ethernet port must be explicitly enabled for RoCE.
When RoCE is not enabled on the port, the NIC will refuse to create
QPs attached to it and incoming RoCE packets will be considered by the
NIC as plain Ethernet packets.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Expose the new flow steering API and remove the old
one.
Few changes are required:
1. The Ethernet flow steering follows the existing implementation, but uses
the new steering API. The old flow steering implementation is removed.
2. Move the E-switch FDB management to use the new API.
3. When driver is loaded call to mlx5_init_fs which initialize
the flow steering tree structure, open namespaces for NIC receive
and for E-switch FDB.
4. Call to mlx5_cleanup_fs when the driver is unloaded.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow steering initialization is based on static tree which
illustrates the flow steering tree when the driver is loaded. The
initialization considers the max supported flow table level of the device,
a minimum of 2 kernel flow tables(vlan and mac) are required to have
kernel flow table functionality.
The tree structures when the driver is loaded:
root_namespace(receive nic)
|
priority-0 (kernel priority)
|
namespace(kernel namespace)
|
priority-0 (flow tables priority)
In the following patches, When the EN driver will use the flow steering
API, it create two flow tables and their flow groups under
priority-0(flow tables priority).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new Flow Steering (FS) firmware commands,
in-order to support the new flow steering infrastructure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-Switch vport context is unlike NIC vport context, managed by the
E-Switch manager or vport_group_manager and not by the NIC(VF) driver.
The E-Switch manager can access (read/modify) any of its vports
E-Switch context.
Currently E-Switch vport context includes only clietnt and server
vlan insertion and striping data (for later support of VST mode).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling E-Switch SRIOV for nvfs+1 vports.
Create E-Switch FDB for L2 UC/MC mac steering between VFs/PF and
external vport (Uplink).
FDB contains forwarding rules such as:
UC MAC0 -> vport0(PF).
UC MAC1 -> vport1.
UC MAC2 -> vport2.
MC MACX -> vport0, vport2, Uplink.
MC MACY -> vport1, Uplink.
For unmatched traffic FDB has the following default rules:
Unmached Traffic (src vport != Uplink) -> Uplink.
Unmached Traffic (src vport == Uplink) -> vport0(PF).
FDB rules population:
Each NIC vport (VF) will notify E-Switch manager of its UC/MC vport
context changes via modify vport context command, which will be
translated to an event that will be handled by E-Switch manager (PF)
which will update FDB table accordingly.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define needed hardware structures and capabilities needed
for E-Switch FDB flow tables and read them on driver load.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-Switch is the software entity that represents and manages ConnectX4
inter-HCA ethernet l2 switching.
E-Switch has its own Virtual Ports, each Vport/vNIC/VF can be
connected to the device through a vport of an e-switch.
Each e-switch is managed by one vNIC identified by
HCA_CAP.vport_group_manager (usually it is the PF/vport[0]),
and its main responsibility is to forward each packet to the
right vport.
e-Switch needs to manage its own l2-table and FDB tables.
L2 table is a flow table that is managed by FW, it is needed for
Multi-host (Multi PF) configuration for inter HCA switching between
PFs.
FDB table is a flow table that is totally managed by e-Switch driver,
its main responsibility is to switch packets between e-Swtich internal
vports and uplink vport that belong to the same.
This patch introduces only e-Swtich l2 table management, FDB managemnt
will come later when ethernet SRIOV/VFs will be enabled.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are needed to notify the upcoming L2 table and SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) vlan table changes.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are needed to notify the upcoming SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) promisc mode changes.
Preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for SR-IOV we add here an API to enable each e-switch
manager (PF) to configure its VFs link states in e-switch
preparation for ethernet sriov.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are needed to notify the upcoming L2 table and SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) UC/MC mac lists
changes.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for SR-IOV we add here an API to enable each e-switch
client (PF/VF) to configure its L2 MAC addresses and for the e-switch
manager (usually the PF) to access them in order to be able to
configure them into the e-switch.
Therefore we now pass vport num parameter to
mlx5_query_nic_vport_context, so PF can access other vports contexts.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update HCA capabilities and HW struct to include needed
capabilities for upcoming Ethernet Switch (SR-IOV E-Switch).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds SRIOV base support for mlx5 supported devices. The same
driver is used for both PFs and VFs; VFs are identified by the driver
through the flag MLX5_PCI_DEV_IS_VF added to the pci table entries.
Virtual functions are created as usual through writing a value to the
sriov_numvs sysfs file of the PF device. Upon instantiating VFs, they will
all be probed by the driver on the hypervisor. One can gracefully unbind
them through /sys/bus/pci/drivers/mlx5_core/unbind.
mlx5_wait_for_vf_pages() was added to ensure that when a VF dies without
executing proper teardown, the hypervisor driver waits till all of the
pages that were allocated at the hypervisor to maintain its operation
are returned.
In order for the VF to be operational, the PF needs to call enable_hca
for it. This can be done before the VFs are created through a call to
pci_enable_sriov.
If the there are VFs assigned to a VMs when the driver of the PF is
unloaded, all the VF will experience system error and PF driver unloads
cleanly; in this case pci_disable_sriov is not called and the devices
will show when running lspci. Once the PF driver is reloaded, it will
sync its data structures which maintain state on its VFs.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent outgoing multicast frames from looping back to the RX queue.
By introducing new HW capability self_lb_en_modifiable, which indicates
the support to modify self_lb_en bit in modify_tir command.
When this capability is set we can prevent TIRs from sending back
loopback multicast traffic to their own RQs, by "refreshing TIRs" with
modify_tir command, on every time new channels (SQs/RQs) are created at
device open.
This is needed since TIRs are static and only allocated once on driver
load, and the loopback decision is under their responsibility.
Fixes issues of the kind:
"IPv6: eth2: IPv6 duplicate address fe80::e61d:2dff:fe5c:f2e9 detected!"
The issue is seen since the IPv6 solicitations multicast messages are
loopedback and the network stack thinks they are coming from another host.
Fixes: 5c50368f38 ("net/mlx5e: Light-weight netdev open/stop")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On device initialization, wait till firmware indicates that that it is done
with initialization before proceeding to initialize the device.
Also update initialization segment layout to match driver/firmware
interface definitions.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement the pci_error_handlers for mlx5_core which allow the
driver to recover from PCI error.
Once an error is detected in the PCI, the mlx5_pci_err_detected is called
and it:
1) Marks the device to be in 'Internal Error' state.
2) Dispatches an event to the mlx5_ib to flush all the outstanding cqes
with error.
3) Returns all the on going commands with error.
4) Unloads the driver.
Afterwards, the FW is reset and mlx5_pci_slot_reset is called and it
enables the device and restore it's pci state.
If the later succeeds, mlx5_pci_resume is called, and it loads the SW
stack.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The detection of a fatal condition has been updated to take into account
the state reported by the device or by detecting an all ones read of the
firmware version which indicates that the device is not accessible.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a single threaded work queue for each device in the system instead of
using one thread for any device. This is required so we can concurrently
process system error handling for all the devices that need that.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to handling system errors at the mlx5_core level, change the
interface of cmd_work_handler to accept a 64 bit argument for the vector.
This allows to encode a flag that signifies when the handler is called
as a result of a driver logic that wishes to terminate commands that
the hardware may not be able to terminate. Such command completions
are detected at the handler and proper return status is encoded.
To be able to terminate page handler commands, we make sure to set
the corresponding bit in the bitmask.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name refers to syndrome so uset ext_synd instread of ext_sync.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 96249d70dd ("IB/core: Guarantee that a local_dma_lkey
is available") allows ULPs that make use of the local dma key to keep
working as before by allocating a DMA MR with local permissions and
converted these consumers to use the MR associated with the PD
rather then device->local_dma_lkey.
ConnectIB has some known issues with memory registration
using the local_dma_lkey (SEND, RDMA, RECV seems to work ok).
Thus don't expose support for it (remove device->local_dma_lkey
setting), and take advantage of the above commit such that no regression
is introduced to working systems.
The local_dma_lkey support will be restored in CX4 depending on FW
capability query.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing
read and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc. mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EHLg
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull inifiniband/rdma updates from Doug Ledford:
"This is a fairly sizeable set of changes. I've put them through a
decent amount of testing prior to sending the pull request due to
that.
There are still a few fixups that I know are coming, but I wanted to
go ahead and get the big, sizable chunk into your hands sooner rather
than waiting for those last few fixups.
Of note is the fact that this creates what is intended to be a
temporary area in the drivers/staging tree specifically for some
cleanups and additions that are coming for the RDMA stack. We
deprecated two drivers (ipath and amso1100) and are waiting to hear
back if we can deprecate another one (ehca). We also put Intel's new
hfi1 driver into this area because it needs to be refactored and a
transfer library created out of the factored out code, and then it and
the qib driver and the soft-roce driver should all be modified to use
that library.
I expect drivers/staging/rdma to be around for three or four kernel
releases and then to go away as all of the work is completed and final
deletions of deprecated drivers are done.
Summary of changes for 4.3:
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular
tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing read
and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (136 commits)
IB/ipoib: Suppress warning for send only join failures
IB/ipoib: Clean up send-only multicast joins
IB/srp: Fix possible protection fault
IB/core: Move SM class defines from ib_mad.h to ib_smi.h
IB/core: Remove unnecessary defines from ib_mad.h
IB/hfi1: Add PSM2 user space header to header_install
IB/hfi1: Add CSRs for CONFIG_SDMA_VERBOSITY
mlx5: Fix incorrect wc pkey_index assignment for GSI messages
IB/mlx5: avoid destroying a NULL mr in reg_user_mr error flow
IB/uverbs: reject invalid or unknown opcodes
IB/cxgb4: Fix if statement in pick_local_ip6adddrs
IB/sa: Fix rdma netlink message flags
IB/ucma: HW Device hot-removal support
IB/mlx4_ib: Disassociate support
IB/uverbs: Enable device removal when there are active user space applications
IB/uverbs: Explicitly pass ib_dev to uverbs commands
IB/uverbs: Fix race between ib_uverbs_open and remove_one
IB/uverbs: Fix reference counting usage of event files
IB/core: Make ib_dealloc_pd return void
IB/srp: Create an insecure all physical rkey only if needed
...
The mlx5 driver exposes device capability IB_DEVICE_LOCAL_DMA_LKEY
but does not set the the device local_dma_lkey. This breaks
rpcrdma drivers.
Query and set this lkey when creating the device resources.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Only rx/tx pause settings.
Autoneg setting is currently not supported.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Port speed settings are applied by the device only upon
port admin status transition from DOWN to UP.
So we enforce this transition regardless of the port's
current operation state (which may be occasionally DOWN if
for example the network cable is disconnected).
- Fix the PORT_UP/DOWN device interface enum
- Set the local_port bit in the device PAOS register
- EXPORT the PAOS (Port Administrative and Operational Status)
register set/query access functions.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added physical port counters in the following standard formats to
ethtool statistics:
- IEEE 802.3
- RFC2863
- RFC2819
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A regular TX WQE execution involves two or more DMA reads -
one to fetch the WQE, and another one per WQE gather entry.
These DMA reads obviously increase the TX latency.
There are two mlx5 mechanisms to bypass these DMA reads:
1) Inline WQE
2) Blue Flame (BF)
An inline WQE contains a whole packet, thus saves the DMA read/s
of the regular WQE gather entry/s. Inline WQE support was already
added in the previous commit.
A BF WQE is written directly to the device I/O mapped memory, thus
enables saving the DMA read that fetches the WQE.
The BF WQE I/O write must be in cache line granularity, thus uses
the CPU write combining mechanism.
A BF WQE I/O write acts also as a TX doorbell for notifying the
device of new TX WQEs.
A BF WQE is written to the same I/O mapped address as the regular TX
doorbell, thus this address is being mapped twice - once by ioremap()
and once by io_mapping_map_wc().
While both mechanisms reduce the TX latency, they both consume more CPU
cycles than a regular WQE:
- A BF WQE must still be written to host memory, in addition to being
written directly to the device I/O mapped memory.
- An inline WQE involves copying the SKB data into it.
To handle this tradeoff, we introduce here a heuristic algorithm that
strives to avoid using these two mechanisms in case the TX queue is
being back-pressured by the device, and limit their usage rate otherwise.
An inline WQE will always be "Blue Flamed" (written directly to the
device I/O mapped memory) while a BF WQE may not be inlined (may contain
gather entries).
Preliminary testing using netperf UDP_RR shows that the latency goes down
from 17.5us to 16.9us, while the message rate (tested with pktgen) stays
the same.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By affinity hints and XPS, each mlx5e channel is assigned a CPU
core.
Channel DMA coherent memory that is written by the NIC and read
by SW (e.g CQ buffer) is allocated on the NUMA node of the CPU
core assigned for the channel.
Channel DMA coherent memory that is written by SW and read by the
NIC (e.g SQ/RQ buffer) is allocated on the NUMA node of the NIC.
Doorbell record (written by SW and read by the NIC) is an
exception since it is accessed by SW more frequently.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ConnectX-4 HW implements inverted XOR8.
To make it act as XOR we re-order the HW RSS indirection table.
Set XOR to be the default RSS hash function and add ethtool API to
control it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Enable HW cacheline start padding and align RX WQE size to cacheline
while considering HW start padding. Also, fix dma_unmap call to use
the correct SKB data buffer size.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we configured HW MTU to be netdev->mtu, actually we
need to configure netdev->mtu + (ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN).
Also, query MTU can not fail, hence make the relevant helper a
void functionm, add mlx5e_set_dev_port_mtu, helper function to
handle MTU setting.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix static checker warnings in the flow of system guid query.
Fixes: 707c4602cd ('net/mlx5_core: Add new query HCA vport commands')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following helpers:
1. mlx5_query_port_proto_oper -- queries the port speed port mask
2. mlx5_query_port_link_width_oper - queries the port link with bitmask
3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port
These helpers will be used from the IB driver when working in ISSI > 0 mode.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, mlx5_query_port_ptys always queried port number one.
Added new argument in the function's prototype so we can also query
the second port. This will be needed when thr helper will be invoked
from the IB driver on non FPP (Function-Per-Port) devices.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the function prototypes for max and operational mtu to take the
local port number. In the Ethernet driver is this hard coded to one,
since ConnectX4 Ethernet devices are always function-per-port.
The IB driver also serves older devices (ConnectIB) which isn't such,
and hence the part can vary.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two wrapper functions to the query adapter command:
1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter.
2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the
query_adapter command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the implementation for the following commands:
1. QUERY_HCA_VPORT_GID
2. QUERY_HCA_VPORT_PKEY
3. QUERY_HCA_VPORT_CONTEXT
They will be needed when we move to work with ISSI > 0 in the IB driver too.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the vport header file to be under include/linux/mlx5, such that
the mlx5 IB can use it as well.
Also add nic_ prefix to the vport NIC commands to differeniate between
HCA vport commands and NIC vport commands.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The process_mad device function declares some parameters as "in". Make those
parameters const and adjust the call tree under process_mad in the various
drivers accordingly.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This is the Ethernet part of the driver for the Mellanox ConnectX(R)-4
Single/Dual-Port Adapter supporting 100Gb/s with VPI. The driver
extends the existing mlx5 driver with Ethernet functionality.
This patch contains the driver entry points but does not include
transmit and receive (see the previous patch in the series) routines.
It also adds the option MLX5_CORE_EN to Kconfig to enable/disable the
Ethernet functionality. Currently, Kconfig is programmed to make
Ethernet and Infiniband functionality mutally exclusive.
Also changed MLX5_INFINIBAND to be depandant on MLX5_CORE instead of
selecting it, since MLX5_CORE could be selected without MLX5_INFINIBAND
being selected.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the resource handling files:
- flow_table.c: This file contains the code to handle the low level API
to configure hardware flow table. It is separated from
the flow_table_en.c, because it will be used in the
future by Raw Ethernet QP in mlx5_ib too.
- en_flow_table.[ch]: Ethernet flow steering handling. The flow table
object contain a mapping between flow specs and TIRs.
This mechanism will be used also to configure e-switch
in the future, when SR-IOV support will be added.
- transobj.[ch] - Low level functions to create/modify/destroy the
transport objects: RQ/SQ/TIR/TIS
- vport.[ch] - Handle attributes of a virtual port (vPort) in the
embedded switch. Currently this switch is a passthrough, until SR-IOV
support will be added.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce set/Query low level functions to access MTU in hardware. To be
used by the netdev.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce mlx5_core_modify_cq_moderation() to be used by the netdev, to
set hardware coalescing.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemet get/set port status low level functions to be exposed by the
netdev.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those registers will be used by the ethtool to set/get settings.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Query all supported types of dev caps on driver load.
- Store the Cap data outbox per cap type into driver private data.
- Introduce new Macros to access/dump stored caps (using the auto
generated data types).
- Obsolete SW representation of dev caps (no need for SW copy for each
cap).
- Modify IB driver to use new macros for checking caps.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_ifc.h was heavily modified here since it is now generated by a
script from the device specification (PRM rev 0.25). This specification
is backward compatible to existing hardware.
Some structures/fields were added here in order to enable the Ethernet
functionality of the driver.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for upcoming ethernet driver.
- Move msix array from eq_table struct to priv since its not related to
eq_table
- Intorduce irq_info struct to hold all irq information
- Move name from mlx5_eq to irq_info struct since it is irq property.
- Set IRQ affinity hints
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David Daney pointed in mlx4_core driver [1], mlx5_core is also
misusing the DMA-API.
This patch is removing the code that vmap() memory allocated by
dma_alloc_coherent().
After this patch, users of this drivers might fail allocating resources
on memory fragmeneted systems. This will be fixed later on.
[1] - https://patchwork.ozlabs.org/patch/458531/
CC: David Daney <david.daney@cavium.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for ethernet driver.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass consumer index as a parameter to arm CQ
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for ethernet driver.
These functions will be used in drivers other than mlx5_ib.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use coherent memory for the commands descriptor page. Take measures to make
sure the page is aligned to MLX5_ADAPTER_PAGE_SIZE as required by the hardware.
Reported-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement a page fault handler (leaving the pages pinned as
of time being). The page fault handler handles initiator and responder
page faults for UD/RC transports, for send/receive operations, as well
as RDMA read/write initiator support.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* Refactor MR registration and cleanup, and fix reg_pages accounting.
* Create a work queue to handle page fault events in a kthread context.
* Register a fault handler to get events from the core for each QP.
The registered fault handler is empty in this patch, and only a later
patch implements it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The new function allows updating the page tables of a memory region
after it was created. This can be used to handle page faults and page
invalidations.
Since mlx5_ib_update_mtt will need to work from within page invalidation,
so it must not block on memory allocation. It employs an atomic memory
allocation mechanism that is used as a fallback when kmalloc(GFP_ATOMIC) fails.
In order to reuse code from mlx5_ib_populate_pas, the patch splits
this function and add the needed parameters.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch wraps together several changes needed for on-demand paging support
in the mlx5_ib_populate_pas function, and when registering memory regions.
* Instead of accepting a UMR bit telling the function to enable all
access flags, the function now accepts the access flags themselves.
* For on-demand paging memory regions, fill the memory tables from the
correct list, and enable/disable the access flags per-page according
to whether the page is present.
* A new bit is set to enable writing of access flags when using the
firmware create_mkey command.
* Disable contig pages when on-demand paging is enabled.
In addition the patch changes the UMR code to use PTR_ALIGN instead of
our own macro.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* Add a handler function pointer in the mlx5_core_qp struct for page
fault events. Handle page fault events by calling the handler
function, if not NULL.
* Add on-demand paging capability query command.
* Export command for resuming QPs after page faults.
* Add various constants related to paging support.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In commit 0c7aac854f ("net/mlx5_core: Remove unused dev cap enum
fields"), the flag MLX5_DEV_CAP_FLAG_ON_DMND_PG was removed.
Unfortunately the on-demand paging changes actually use it, so re-add
the missing flag.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add a helper function mlx5_ib_read_user_wqe to read information from
user-space owned work queues. The function will be used in a later
patch by the page-fault handling code in mlx5_ib.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
[ Add stub for ib_umem_copy_from() for CONFIG_INFINIBAND_USER_MEM=n
- Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current UMR interface doesn't allow partial updates to a memory
region's page tables. This patch changes the interface to allow that.
It also changes the way the UMR operation validates the memory
region's state. When set, IB_SEND_UMR_FAIL_IF_FREE will cause the UMR
operation to fail if the MKEY is in the free state. When it is
unchecked the operation will check that it isn't in the free state.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- Large set of iSER initiator improvements
- Hardware driver fixes for cxgb4, mlx5 and ocrdma
- Small fixes to core midlayer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+ABw
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/RDMA updates from Roland Dreier:
- large set of iSER initiator improvements
- hardware driver fixes for cxgb4, mlx5 and ocrdma
- small fixes to core midlayer
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (47 commits)
RDMA/cxgb4: Fix ntuple calculation for ipv6 and remove duplicate line
RDMA/cxgb4: Add missing neigh_release in find_route
RDMA/cxgb4: Take IPv6 into account for best_mtu and set_emss
RDMA/cxgb4: Make c4iw_wr_log_size_order static
IB/core: Fix XRC race condition in ib_uverbs_open_qp
IB/core: Clear AH attr variable to prevent garbage data
RDMA/ocrdma: Save the bit environment, spare unncessary parenthesis
RDMA/ocrdma: The kernel has a perfectly good BIT() macro - use it
RDMA/ocrdma: Don't memset() buffers we just allocated with kzalloc()
RDMA/ocrdma: Remove a unused-label warning
RDMA/ocrdma: Convert kernel VA to PA for mmap in user
RDMA/ocrdma: Get vlan tag from ib_qp_attrs
RDMA/ocrdma: Add default GID at index 0
IB/mlx5, iser, isert: Add Signature API additions
Target/iser: Centralize ib_sig_domain setting
IB/iser: Centralize ib_sig_domain settings
IB/mlx5: Use extended internal signature layout
IB/iser: Set IP_CSUM as default guard type
IB/iser: Remove redundant assignment
IB/mlx5: Use enumerations for PI copy mask
...
Rather than using the basic BSF layout which utilizes a pre-configured
signature settings (sufficient for current DIF implementation), we use
the extended BSF layout to expose advanced signature settings. These
settings will also be exposed to the user later.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case input and output space parameters match, we can use a copy
mask from input and output space. Use enums for those.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch puts a common part as the first field of mlx5_core_qp. This field is
used to identify which resource generated an event. This is required since upcoming
new resource types such as DC targets are allocated for the same numerical space
as regular QPs and may generate the same events. By searching the resource in the
same table we can then look at the common field to identify the resource.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transform device capabilities related commands to use set/get macros to
manipulate command mailboxes.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an auto generated header file that describes hardware registers along with
set of macros that set/get values. The macros do static checks to avoid
overflow, handle endianess, and overall provide a clean way to code commands.
Currently the header file is small and we will add structs as we make use of
the macros.
A few commands were removed from the commands enum since they are not supported
currently and will be added when support is available.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange struct mlx5_caps so it has a "gen" field to represent the current
capabilities configured for the device. Max capabilities can also be queried
from the device. Also update capabilities struct to contain more fields as per
the latest revision if firmware specification.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
In the event flow, we currently pass only a port number in the
void *data argument. Rather than pass a pointer to the event handlers,
we should use an "unsigned long" parameter, and pass the port number
value directly.
In the future, if necessary for some events, we can use the unsigned long
parameter to pass a pointer.
Based on a patch by Eli Cohen <eli@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places where parameters which should be u8/u16 were
integer type.
Additionally, in 2 places, a check for a non-null pointer was added
before dereferencing the pointer (this is actually a bug fix).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for a new mlx5 device which is VPI (i.e., ports can be
either IB or ETH), move the pci device functionality from mlx5_ib
to mlx5_core.
This involves the following changes:
1. Move mlx5_core_dev struct out of mlx5_ib_dev. mlx5_core_dev
is now an independent structure maintained by mlx5_core.
mlx5_ib_dev now has a pointer to that struct.
This requires changing a lot of places where the core_dev
struct was accessed via mlx5_ib_dev (now, this needs to
be a pointer dereference).
2. All PCI initializations are now done in mlx5_core. Thus,
it is now mlx5_core which does pci_register_device (and not
mlx5_ib, as was previously).
3. mlx5_ib now registers itself with mlx5_core as an "interface"
driver. This is very similar to the mechanism employed for
the mlx4 (ConnectX) driver. Once the HCA is initialized
(by mlx5_core), it invokes the interface drivers to do
their initializations.
4. There is a new event handler which the core registers:
mlx5_core_event(). This event handler invokes the
event handlers registered by the interfaces.
Based on a patch by Eli Cohen <eli@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is beyond silly:
struct timespec ts = ktime_get_ts();
ktime_t ktime = timespec_to_ktime(ts);
Further down the code builds the delta of two ktime_t values and
converts the result to nanoseconds.
Use ktime_get_ns() and replace all the nonsense.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Eli Cohen <eli@mellanox.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The patch stores iova, pd and size during mr creation and after UMRs
that modify them. It removes the unused access flags field.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add support for the block multicast loopback QP creation flag along
the proper firmware API for that.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This commit takes care of the generated signature error CQE generated
by the HW (if happened). The underlying mlx5 driver will handle
signature error completions and will mark the relevant memory region
as dirty.
Once the consumer gets the completion for the transaction, it must
check for signature errors on signature memory region using a new
lightweight verb ib_check_mr_status().
In case the user doesn't check for signature error (i.e. doesn't call
ib_check_mr_status() with status check IB_MR_CHECK_SIG_STATUS), the
memory region cannot be used for another signature operation
(REG_SIG_MR work request will fail).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch implements IB_WR_REG_SIG_MR posted by the user.
Baisically this WR involves 3 WQEs in order to prepare and properly
register the signature layout:
1. post UMR WR to register the sig_mr in one of two possible ways:
* In case the user registered a single MR for data so the UMR data segment
consists of:
- single klm (data MR) passed by the user
- BSF with signature attributes requested by the user.
* In case the user registered 2 MRs, one for data and one for protection,
the UMR consists of:
- strided block format which includes data and protection MRs and
their repetitive block format.
- BSF with signature attributes requested by the user.
2. post SET_PSV in order to set the memory domain initial
signature parameters passed by the user.
SET_PSV is not signaled and solicited CQE.
3. post SET_PSV in order to set the wire domain initial
signature parameters passed by the user.
SET_PSV is not signaled and solicited CQE.
* After this compound WR we place a small fence for next WR to come.
This patch also introduces some helper functions to set the BSF correctly
and determining the signature format selectors.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This will be useful when processing signature errors on a specific
key. The mlx5 driver will lookup the matching mlx5 memory region
structure and mark it as dirty (contains signature errors).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If user requested signature enable we initialize relevant mlx5_ib_qp
members. We mark the qp as sig_enable and we increase the effective
SQ size, but still limit the user max_send_wr to original size
computed. We also allow the create_qp routine to accept sig_enable
create flag.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Support create_mr and destroy_mr verbs. Creating ib_mr may be done
for either ib_mr that will register regular page lists like
alloc_fast_reg_mr routine, or indirect ib_mrs that can register other
(pre-registered) ib_mrs in an indirect manner.
In addition user may request signature enable, that will mean that the
created ib_mr may be attached with signature attributes (BSF, PSVs).
Currently we only allow direct/indirect registration modes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
On some architectures (for example, arm), we don't end up indirectly
pulling in the declaration of kzalloc() and kfree(), and so building
anything that includes <linux/mlx5/driver.h> breaks. Fix this by adding
an explicit include to get the declaration.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Saeed Mahameed