The Cross-chip Port Based VLAN Table (PVT) is currently initialized with
all ones, allowing any external ports to egress frames on local ports.
This commit implements the PVT access functions and programs the PVT
with all ones for the local switch ports only, instead of using the Init
operation. The current behavior is unchanged for the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cross-chip Port Based VLAN Table (PVT) supports two indexing modes,
one using 5-bit for device and 4-bit for port, the other using 4-bit for
device and 5-bit for port, configured via the Global 2 Misc register.
Only 4 bits for the source port are needed when interconnecting 88E6xxx
switch devices since they all support less than 16 physical ports. The
full 5 bits are needed when interconnecting a device with 98DXxxx switch
devices since they support more than 16 physical ports.
Add a mv88e6xxx_pvt_setup helper to set the 4-bit port PVT mode, which
will be extended later to also initialize the PVT content.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all Marvell switch chips feature a Cross-chip Port VLAN Table (PVT).
Chips with a PVT use the same implementation, so a new mv88e6xxx_ops
member won't be necessary yet. Add a "pvt" boolean member to the
mv88e6xxx_info structure and kill the obsolete MV88E6XXX_FLAGS_PVT flag.
Add a mv88e6xxx_has_pvt helper to wrap future checks of that condition.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
I do not hold the copyright of the DSA core and drivers source files,
since these changes have been written as an initiative of my day job.
Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't support 88E6391 anywhere in the code, so remove the unused
mv88e6391_ops structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_info structure for the 88E6191 chip was pointing the
mv88e6391_ops definition instead of mv88e6191_ops. Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The related mv88e6xxx_ops structure was misplaced. Reorder it correctly
to fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The related mv88e6xxx_ops and mv88e6xxx_info structure were misplaced.
Reorder them correctly to fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA has ageing time limits, specify them when registering a
switch so that out-of-range values are handled correctly by the core.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reported-by: Jason Cobham <jcobham@questertangent.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new operation to disable the DA, SA and VTU priority override.
Setting such limit is not likely to be used soon, so provide a
port_disable_pri_override operation directly. This can be changed later
for port_set_pri_override when we'll need it.
Also remove the now obsolete mv88e6xxx_6320_family helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new operation to disable the limiting of learnt MAC addresses.
Setting such limit is not likely to be used soon, so provide a
port_disable_learn_limit operation directly. This can be changed later
for port_set_learn_limit when we'll need it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell switch ports can be configured to allow or prevent egress of
frames with an unknown unicast or multicast destination address.
Some switch chips such as 88E6095 and 88E6185 have two disjoint bits in
Port Control Register (0x04) bit 2 "Forward Unknown" (for unicast) and
Port Control 2 Register (0x08) bit 6 "Default Forward" (for multicast).
Other chips such as 88E6085, 88E6123, 88E6352, and 88E6390 have a 2-bit
value in Port Control Register (0x04) bits 3:2 "EgressFloods".
The current code does not fully implement the disjoint bits variant and
assigns incorrect ones to some chip models. Fix that with two
implementation references (6185 and 6352 that I currently have) of a
port_set_egress_floods operation (as named in datasheets).
Old chips such as 88E6060 don't have egress flooding mode, so don't
error out if the operation is not provided.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A switch port mode is defined by the association of its egress mode, its
frame mode and if supported or required, the ether type value.
Pack all this in a mv88e6xxx_set_port_mode function and provide helpers
for the Normal Network mode, the DSA mode, and the Ether Type DSA mode,
as well as an helper to setup a port's mode depending on its nature.
Define PORT_ETH_TYPE_DEFAULT for the 0x9100 reset value of port E Type.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all Marvell switch chips support port trunking, which is embedded in
the port vector data for ATU operations.
Rename the portv_trunkid member of the mv88e6xxx_atu_entry structure to
portvec to be more concise and consistent with the different chips.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the _mv88e6xxx_fid_new helper to mv88e6xxx_atu_new to get rid of
the old underscore prefix naming convention and be consistent with the
rest of the chip-wide ATU API.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a fresh documented implementation of the ATU Move operation, and use
it to replace the current ATU Remove operation.
Note that not all Marvell switch chip support the ATU Move operation.
For those supporting it, the number of bits used to mask the destination
port may vary. 6352 and such use 4-bit, while 6390 use 5-bit. Thus add a
new atu_move_port_mask member in the info structure to describe the
presence and variant of ATU Move operation.
Note that the ATU Move operation is not documented in the 6185 datasheet
but the chip does support the operation.
All remaining _mv88e6xxx_atu_* functions are now unused as well as the
MV88E6XXX_FLAG_G1_ATU_FID flag, thus remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a fresh documented implementation of the ATU Flush/Move operation.
Use it to replace the current ATU Flush operation.
_mv88e6xxx_atu_flush_move is still used by the Move operation so keep it
until the Move operation is refactored in a next commit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use a fresh documented implementation of the ATU GetNext.
Since it is not necessary to write the MAC address to iterate from, only
do it once directly in the ATU GetNext operation, if the provided ATU
entry structure is not valid. This makes the user code simpler.
Also, there is no need to loop when getting a single ATU entry. So
remove the mv88e6xxx_atu_get helper and add a simpler snippet in
mv88e6xxx_port_db_load_purge to lookup a given MAC address.
The _mv88e6xxx_atu_mac_{read,write} are not used anymore thus remove
them. _mv88e6xxx_atu_data_{read,write} are still used so keep them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch chips have an ATU accessed using the same Global (1)
register layout. Only the handling of the FID differs as more bits were
necessary to support more and more databases.
Add and use a fresh documented implementation of the ATU Load/Purge.
The static mv88e6xxx_g1_atu_{fid_write,op_wait,op,data_write,mac_write}
functions won't need to be exposed in the end so for the moment keep
their counterparts _mv88e6xxx_atu_{wait,cmd,data_write,mac_write} as is,
since they are still used by other ATU operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU Learn2All feature allows newly learnt addresses to be spanned on
ports marked as "Message Port", currently all DSA ports.
This commit enables this feature which is necessary and quite convenient
for multi-chip switch fabrics.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All interconnectable Marvell switch chips have an ATU Learn2All feature
which allows newly learnt addresses to be spanned on ports marked as
"Message Port".
This commit configures the DSA ports as Message Port. Note that this has
no effect until the Learn2All feature is enabled.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the configuration of the default ageing time in a new
mv88e6xxx_atu_setup function.
That function will be extended later to contain all ATU related
configuration bits.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the ATU ageing time setter code in a new global1_atu.c file, which
will be extended in future patches to contains all consequent Global (1)
ATU support code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6097 chip requires watchdog_ops to be set.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ops needed to support the watchdog for the MV88E6390
family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch contains a watchdog looking for issues with the internal
gubbins of the switch. Hook the interrupt the watchdog triggers and
log the value of the control register indicating why the watchdog
fired. The watchdog can only be cleared with a switch reset, which
will destroy the current configuration. Rather than doing this, just
disable the interrupt.
The mv88e6390 family has different watchdog registers. So use an ops
structure, so support for the mv88e6390 family can be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the remaining port configuration code which varies per device
into port.c, using ops were necessary. This makes
mv88e6xxx_6185_family() and mv88e6xxx_6095_family() unused, so remove
them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike most ports, ports 9 and 10 of the 6390X family have configurable
PHY modes. Set the mode as part of adjust_link().
Ordering is important, because the SERDES interfaces connected to
ports 9 and 10 can be split and assigned to other ports. The CMODE has
to be correctly set before the SERDES interface on another port can be
configured. Such configuration is likely to be performed in
port_enable() and port_disabled(), called on slave_open() and
slave_close().
The simple case is port 9 and 10 are used for 'CPU' or 'DSA'. In this
case, the CMODE is set via a phy-mode in dsa_cpu_dsa_setup(), which is
called early in the switch setup.
When ports 9 or 10 are used as user ports, and have a fixed-phy, when
the fixed fixed-phy is attached, dsa_slave_adjust_link() is called,
which results in the adjust_link function being called, setting the
cmode. The port_enable() will for other ports will be called much
later.
When ports 9 or 10 are used as user ports and have a real phy attached
which does not use all the available SERDES interface, e.g. a 1Gbps
SGMII, there is currently no mechanism in place to set the CMODE of
the port from software. It must be hoped the stripping resistors are
correct.
At the same time, add a function to get the cmode. This will be needed
when configuring the SERDES interfaces.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 family uses a different ATU age timer coefficient.
Fix the info structures.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal PHYs of the mv88e6390 do not have a model ID. Trap any
calls to the ID register, and if it is zero, return the ID for the
mv88e6390. The Marvell PHY driver can then bind to this ID.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces.
It belongs to the Topaz family and unlike the 88E6341 it does not have
a TCAM.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces. It is partially compatible with switches of family
88E6352 and switches of family 88E6390.
This commit adds an initial support for this switch by describing its
capabilities to the driver and introducing a new family.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell ethernet switches have internal ethernet transceivers with
hardcoded phy addresses. These addresses can be greater than the number
of ports or its value might be different than the associated port number.
This is for example the case for MV88E6341 that has 6 ports and internal
Port 1 to Port4 PHYs mapped at SMI addresses from 0x11 to 0x14.
This commits fixes the issue by removing the condition in MDIO callbacks.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.
Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.
Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.
This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has multiple MDIO busses. Generalize the parsing of the
device tree to support multiple mdio nodes. The external mdio bus has
a compatible strings to indicate it is external.
Keep a linked list of busses, placing the external mdio bus at the
tail of the list. When within the driver an mdio bus is needed,
e.g. for EEE or SERDES, use the head of the list which should be the
internal bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have the MDIO bus driver code allocate a private structure and make
the chip a member of it. This will allow us to add further members in
the future.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple MDIO busses, pass the mii_bus
structure to all PHY operations. It will in future then be clear on
which MDIO bus the operation should be performed.
For reads/write from phylib, the mii_bus is readily available. However
some internal code also access the PHY, e.g. for EEE and SERDES. Make
this code use the one and only currently available MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family has the internal PHYs mapped directly onto the
SMI register space as the switch. So the registers can be read
directly. Put a wrapper around this, in preparation for changing the
signature in order to support the external MDIO bus of the 6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 6352 chip has a 8-bit address/16-bit data EEPROM access.
The Marvell 6390 chip has a 16-bit address/8-bit data EEPROM access.
This patch implements the 8-bit data EEPROM access in the mv88e6xxx
driver and adds its support to chips of the 6390 family.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have properly encapsulated and made drivers utilize exported
functions, we can switch dsa_switch_ops to be a annotated with const.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for making struct dsa_switch_ops const, encapsulate it
within a dsa_switch_driver which has a list pointer and a pointer to
dsa_switch_ops. This allows us to take the list_head pointer out of
dsa_switch_ops, which is written to by {un,}register_switch_driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lookup in the ATU can be performed starting from a given MAC
address. This is faster than starting with the first possible MAC
address and iterating all entries.
Entries are returned in numeric order. So if the MAC address returned
is bigger than what we are searching for, we know it is not in the
ATU.
Using the benchmark provided by Volodymyr Bendiuga
<volodymyr.bendiuga@gmail.com>,
https://www.spinics.net/lists/netdev/msg411550.html
on an Marvell Armada 370 RD, the test to add a number of static fdb
entries went from 1.616531 seconds to 0.312052 seconds.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices, such as the mv88e6097 do have ADDR[0] external and so it
is possible to configure the device to use SMI address 0x1. Remove the
restriction, as there are boards using this address.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@westermo.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A port is not necessarily assigned to a netdev. And a port does not
need to be a member of a bridge. So when iterating over all ports,
check before using the netdev and bridge_dev for a port. Otherwise we
dereference a NULL pointer.
Fixes: da9c359e19 ("net: dsa: mv88e6xxx: check hardware VLAN in use")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell chips can enable/disable the PPU on demand. This is needed
to access the PHY registers when there is no indirection mechanism.
Add two new ppu_enable and ppu_disable ops to describe this and finally
get rid of the MV88E6XXX_FLAG_PPU* flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips have different way to issue a software reset.
Old chips (such as 88E6060) have a reset bit in an ATU control register.
Newer chips moved this bit in a Global control register. Chips with
controllable PPU should reset the PPU when resetting the switch.
Add a new reset operation to implement these differences and introduce a
mv88e6xxx_software_reset() helper to wrap it conveniently.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an helper to toggle the eventual GPIO connected to the reset pin.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before resetting a switch, the ports should be set to the Disabled state
and the transmit queues should be drained.
Add an helper to explicit that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DSA_TAG_PROTO_EDSA as tag_protocol for the mv88e6097. The
initialisation was missing before.
Fixes: a1f482aa8c33 ("net: dsa: mv88e6xxx: Move the tagging protocol into info")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has a number flow control registers accessed via the
Flow Control register. Use these to set the pause control.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has a different mechanism for configuring pause.
Refactor the code into an ops function, and for the moment, don't add
any mv88e6390 code yet.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two different rate limiting configurations, depending on the
switch generation. Refactor this into ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches support jumbo frames. Refactor this code into operations
in the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older devices have a couple of registers in global2. The mv88e6390
family has a single register in global1 behind which hides similar
configuration. Implement and op for this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips only support DSA tagging. Newer chips have both DSA and
EDSA tagging. Refactor the code by adding port functions for setting the
frame mode, egress mode, and if to forward unknown frames.
This results in the helper mv88e6xxx_6065_family() becoming unused, so
remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Verify mandatory ops for port setup
Don't set ether type for DSA port.
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips support a single tagging protocol, DSA. New chips support
both DSA and EDSA, an enhanced version. Having both as an option
changes the register layouts. Up until now, it has been assumed that
if EDSA is supported, it will be used. Hence the register layout has
been determined by which protocol should be used. However, mv88e6390
has a different implementation of EDSA, which requires we need to use
the DSA tagging. Hence separate the selection of the protocol from the
register layout.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 changes the monitor control register into the Monitor
and Management control, which is an indirection register to various
registers.
Add ops to set the CPU port and the ingress/egress port for both
register layouts, to global1
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 does not have the two registers to set the frame
priority map. Instead it has an indirection registers for setting a
number of different priority maps. Refactor the old code into an
function, implement the mv88e6390 version, and use an op to call the
right one.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g1_irq_setup() sets up chip->g1_irq.nirqs interrupt mappings,
so free the same amount. This will be 8 or 9 in practice, less than 16.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing comment for the MV88E6097 because of unification.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing definition of g1_irqs for MV88E6097.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the stats functions which access global 1 registers into
global1.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename functions to avoid _ prefix.
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics unit on the mv88e6390 needs the histogram mode to be
configured in a different register compared to other devices. Add an
ops to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename to mv88e6390_g1_stats_set_histogram
Move into global1.c
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 has a control register for what the histogram statistics
actually contain. This means the stat_snapshot method should not set
this information. So implement the 6390 stats_snapshot function without
these bits.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing the family of device belongs to helps with picking the ops
implementation which is appropriate to the device. So add a comment to
each structure of ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a stats snapshot differs between same families. Abstract this
into an ops member. At the same time, move the code into global1.[ch],
since the registers are in the global1 range.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
_mv88e6xxx_stats_wait() did not check the return value from
mv88e6xxx_g1_read(), so the compiler complained about set but unused
err.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch needs to be taken out of reset before we can read its ID
register on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing interrupts requires switch register access to mask the
interrupts. Hence we must hold the register mutex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error, remask the interrupts, release all maps, and remove the
domain. This cannot be done using the mv88e6xxx_g1_irq_free() because
some of these actions are not idempotent.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the g1 interrupt free code such that is masks any further
interrupts, and then releases the interrupt.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to remove an IRQ domain that was not created results in an
Opps. Add the necessary checks that the irqs were created before
freeing them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent refactoring of setting the MAC configuration broke setting
of RGMII delays, via the phy-mode, on the 6351 family. Add the missing
ops to the structure.
Fixes: 7340e5ecdbb1 ("net: dsa: mv88e6xxx: setup port's MAC")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have setters to configure the port's MAC, use them to
refactor the port setup and adjust_link code.
Note that port's MAC speed, duplex or RGMII delay must not be changed
unless the port's link is forced down. So wrap all that in a
mv88e6xxx_port_setup_mac function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the two bits for link, duplex or RGMII delays are used the same
way on chips supporting the said feature, the two bits for speed have
different meaning for most of the chips out there.
Speed value is stored in bits 1:0, 0x3 means unforce (normal detection).
Some chips reuse values for alternative speeds when bit 12 is set.
Newer chips with speed > 1Gbps reuse value 0x3 thus need a new bit 13.
Here are the values to write in register 0x1 to (un)force speed:
| Speed | 88E6065 | 88E6185 | 88E6352 | 88E6390 | 88E6390X |
| ------- | ------- | ------- | ------- | ------- | -------- |
| 10 | 0x0000 | 0x0000 | 0x0000 | 0x2000 | 0x2000 |
| 100 | 0x0001 | 0x0001 | 0x0001 | 0x2001 | 0x2001 |
| 200 | 0x0002 | NA | 0x1001 | 0x3001 | 0x3001 |
| 1000 | NA | 0x0002 | 0x0002 | 0x2002 | 0x2002 |
| 2500 | NA | NA | NA | 0x3003 | 0x3003 |
| 10000 | NA | NA | NA | NA | 0x2003 |
| unforce | 0x0003 | 0x0003 | 0x0003 | 0x0000 | 0x0000 |
This patch implements a generic mv88e6xxx_port_set_speed() function used
by chip-specific wrappers to filter supported ports and speeds.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips such as 88E6352 and 88E6390 can be programmed to add delays
to RXCLK for IND inputs or to GTXCLK for OUTD outputs when port is in
RGMII mode.
Add a port function to program such delays according to the provided PHY
interface mode.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to port's link, add setter to force port's half duplex, full
duplex or let normal duplex detection occurs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the chips will have a port register control bits to force the
port's link up, down, or let normal link detection occurs.
Implement such operation to use it later when setting duplex, etc.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port functions to set the port 802.1Q mode.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port functions to access the ports default VID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to port files to access the ports default FID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a port function to access the Port Based VLAN Map register.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the port STP state setter to the port files.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell switches contains one internal SMI device per port, called
"Port Registers". Depending on the model, the addresses of these devices
start from 0x0, 0x8 or 0x10.
Start moving Port Registers specific code to their own files.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the function
and data fields.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/dsa/mv88e6xxx/chip.c:2866:5: warning:
symbol 'mv88e6xxx_g1_set_switch_mac' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch can have up to two interrupt controllers. One of these
contains the interrupts from the integrated PHYs, so is useful to
export. The Marvell PHY driver can then be used in interrupt mode,
rather than polling, speeding up PHY handling and reducing load on the
MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove EEPROM flags in favor of new {get,set}_eeprom chip-wide
functions in the mv88e6xxx_ops structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a set_switch_mac chip-wide function to mv88e6xxx_ops and remove
MV88E6XXX_FLAG_G2_SWITCH_MAC flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a mv88e6xxx_ops structure to describe supported chip-wide
functions and assign the correct variant to the chip models.
For the moment, add only PHY access routines. This allows to get rid of
the PHY ops structures and the usage of PHY flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot