The different families (80003es2lan, 8257x, ICHx/PCH) supported by the
driver each have their own conditions when the PHY can be powered down.
This patch rewrites the PHY power up/down code to fit with the family-
specific style used in the driver. All pre-existing calls to power up or
down the PHY remain untouched. A new call to power down the PHY when
removing the driver when the interface is down replaces the current call
to reset the PHY in order to reduce power consumption.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two MAC-families that have VLAN filter table register arrays manage
each a bit differently from one another, so provide family-specific
functions for managing the register arrays and function pointers to access
the appropriate function. Also make sure attempts to access these
register arrays are not done on parts not supporting that feature.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx unit hang detection code in e1000e detects other hangs caused by
hardware components (e.g. Rx, DMA units), but it is not possible to detect
exactly which component is hung so it has always assumed a Tx unit hang.
When dumping a message to the system log because of a hang, this patch adds
more data to help narrow the cause of the issue and makes the message
non-Tx-specific. Because this new code reads PHY registers which can
sleep, move it off to a workqueue. This and all previously existing work
tasks in the driver are now cancelled when the driver is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mutex_lock() calls might_sleep() the driver doesn't have to here.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A failure to initialize the identification LED is not a fatal condition and
should allow the init path to continue.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out a pm_qos DMA latency requirement set when the driver is
loaded when parts that support early receive of jumbo frames are probed
could have that requirement overidden if another part supported by the
driver (one that does not support early receive of jumbo frames) is probed
later. Change the DMA latency requirement to be per-interface if needed
instead of per driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e1000_clear_hw_cntrs_*() functions read the registers to clear them.
There is no reason to save the register contents so the temp variable can
be removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set booleans to 'true' or 'false' to make it clear it is a boolean. Also
change instances of TRUE/FALSE in comments to lowercase true/false.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy and nvm operations structures have function pointers that contain
"phy" and "nvm" in the pointer names which are redundant since the
structures are already obviously in phy and nvm structures.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch depends on a previous one that cleans up redundant #includes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was only updating MII stats when an LSC up was detected and
the interface had not already been reported up to netdev. This meant
MII stats returned in response to an SIOCGMIIREG ioctl would always
show a link up if it had ever been up. This was misleading the networking
daemon guessnet, which uses this ioctl, into making improper network port
selections.
This fix adds a call to e1000_phy_read_status() to actively read the
mii stats before responding to the SIOCGMIIREG ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing the ethtool PHY loopback test on PCH-based LOMs (82577 and
82578), disable K1 (a MAC-PHY interconnect low power mode) otherwise
packets might get corrupted.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e1000_get_cable_length_82577() should return a negative value upon
error.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copper links with WoL or management enabled (any condition which prevents
the phy from being powered down when the interface is taken down) were
always reporting link-up when the interface had been taken down. This
is because when the interface is taken down (ifconfig ethx down),
interrupts are disabled. With no interrupts, there is no LSC interrupt,
which is normally required to set "get_link_status", which instructs the
driver to query the device for link state. The fix is to force
get_link_status to true if the interface is not up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using legacy interrupts, do not clean the Rx ring while resetting
otherwise traffic will not pass.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide missing function pointers for ethtool set/get offloads.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing the interrupt timers following an IMS clear has the unwanted
side-effect of flushing all descriptors immediately following a partial
write when interrupts are disabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tests for 82583 in a couple ethtool functions that were missed from the
initial hardware enablement submission.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting WoL feature, check the supplied modes are all supported rather
than checking for no support. This way, if any new modes are added the
driver does not default to not complaining about it if we don't really
support it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the OEM bits in the PHY on 82577/82578, do not restart
autonegotiation if the firmware is blocking it (e.g. when an IDE-R session
is active) because the link must not go down.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A workaround for pre-release versions of 82577 is causing link issues on
some switches. The workaround is no longer needed on production parts so
remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing MTU, save it off prior to resetting otherwise the flow control
thresholds may be miscalculated.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flow control (pause) parameters were changed via ethtool (i.e. enabled
or disabled), the newly calculated thresholds were not being written to the
device for non-fiber media.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page. Also error out if the page select operation
fails.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ec2a2b80f broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not as fancy as coccinelle. Checkpatch errors ignored.
Compile tested allyesconfig x86, not all files compiled.
grep -rPl --include=*.[ch] "\brequest_irq\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\brequest_irq\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks a previous workaround (commit 7d3cabbcc) for an issue
in hardware where noise on the interconnect between the MAC and PHY could
be generated by a lower power mode (K1) at 1000Mbps resulting in bad
packets. Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps
and when the cable is disconnected. The original version of this
workaround was found to be incomplete.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On PCH-based (82577/82578) and some ICH8-based parts (82566) there is an
issue with the hardware automatically configuring the PHY with contents
from the EEPROM after the PHY is reset, so do the configuration by the
driver instead. This was already similarly done for some 82566 parts in
e1000_phy_hw_reset_ich8lan() but needs to be done after other resets,
so move the PHY configuration code to its own function and call after
all PHY resets.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing flow control (pause) parameters, the flow control thresholds
(i.e. when to send XON/XOFF frames) may not be setup correctly on parts
with copper media. Call the existing e1000_set_fc_watermarks()
function to set these thresholds.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch). This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired. The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.
The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses to NVM and PHY/CSR registers on ICHx/PCH-based parts are protected
from concurrent accesses with a mutex that is acquired when the access is
initiated and released when the access has completed. However, the two
types of accesses should not be protected by the same mutex because the
driver may have to access the NVM while already holding the mutex over
several consecutive PHY/CSR accesses which would result in livelock.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike previous ICHx-based parts, the PCH-based parts (82577/82578) require
LPLU (Low Power Link Up, or "reverse auto-negotiation") to be configured in
the PHY rather than the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some conditions (e.g. when AMT is enabled on the system), it is possible
to take an extended period of time to for the driver to acquire the sw/fw/hw
hardware semaphore used to protect against concurrent access of a shared
resource (e.g. PHY registers). This could cause PHY registers to not get
configured properly resulting in link issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performing a dummy read of the PHY Wakeup Control (WUC) register clears the
wakeup enable bit set by an PHY reset. If this bit remains set, link
problems may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx
state in order for the PHY write which disables gigabit speed to take
effect. Gigabit speed must be disabled in order for the PHY writes to
registers on page 800 (the wakeup control registers) to work as expected
otherwise the system might not wake via WoL.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fd8235bb overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There appears to have been a mixup in the max supported jumbo frame size
between 82574 and 82583 which ended up disabling jumbo frames on the 82574
as a result. This patch swaps the two so that this issue is resolved.
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=14261
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only error returned by pci_{en,dis}able_pcie_error_reporting() is
-EIO which simply means that Advanced Error Reporting is not supported.
There is no need to report that, so remove the error check from e1000e,
igb and ixgbe.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 111b9dc5 ("e1000e: add aer support") introduces pcie aer
support for e1000e, but it is not reasonable to disable it in
e1000_remove but enable it in e1000_resume. This patch enables aer
support in e1000_probe.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With manageability (Intel AMT) enabled via BIOS, PHY wakeup does not get
configured on newer parts which use PHY wakeup vs. MAC wakeup which causes
WoL to not work. The driver should configure PHY wakeup whether or not
manageability is enabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bank offset was being incorrectly calculated on ICH9 parts with a bank
size of 8K (instead of the more common 4K bank) which would cause any NVM
writes to be done on the wrong address after switching from bank 1 to bank
0. Additionally, assume we are meant to use bank 0 if a valid bank is not
detected, and remove the unnecessary acquisition of the SW/FW/HW semaphore
when writing to the shadow ram version of the NVM image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ICHx parts, write the EXTCNF_CTRL.SWFLAG bit once when trying to
acquire the SW/FW/HW semaphore instead of multiple times to prevent the
hardware from having problems (especially for systems with manageability
enabled), and extend the timeout for the hardware to set the SWFLAG bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is required for an issue in hardware where noise on the
interconnect between the MAC and PHY could be generated by a lower power
mode (K1) at 1000Mbps resulting in bad packets. Disable K1 while at 1000
Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs may require two reads of the PHY_STATUS register to determine the
link status. If the PHY is being accessed by another thread it is possible
the first read could timeout and fail. In this case, put a delay in so
the second read will pick up the correct link status.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit NVM writes to 4K sections to prevent NVM corruption on larger
sector allocations (up to 64K).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was accessing register bits for features on parts that do
not support that feature. This could cause problems in the hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous workaround for 82578 to avoid link stall causes some PHY
registers to get cleared inadvertently. Add a delay after all LCD resets
to make sure PHY registers are in a stable state before continuing. Also,
after resets check the EEC register for the state of PHY configuration
performed by the MAC for ICH9 and earlier parts (as done before), but check
the LAN_INIT_DONE bit in the STATUS register for ICH10 and newer parts (EEC
doesn't exist in these newer parts).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY loopback on 82578 fails to work as a result of flushing the packets
in the FIFO buffer in the link stall workaround. Don't perform the
workaround if in PHY loopback mode.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
on permanent failure
PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure. This state is not
checked in many of the network drivers.
This patch fixes the omission in the e1000e driver.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last hunk of this commit:
commit 12d04a3c12
Author: Alexander Duyck <alexander.h.duyck@intel.com>
Date: Wed Mar 25 22:05:03 2009 +0000
e1000e: commonize tx cleanup routine to match e1000 & igb
changed the logic for determining if we should call napi_complete or
not at then end of a napi poll.
If the NIC is using MSI-X with no work to do in ->poll, net_rx_action
can just spin indefinitely on older kernels and for 2 jiffies on newer
kernels since napi_complete is never called and budget isn't
decremented.
Discovered and verified while testing driver backport to an older
kernel.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool is a standard way of getting information about
ethernet interfaces. We enhance ethtool kernel interface
& e1000e to make the MDI-X status readable via ethtool in
userspace.
Signed-off-by: Chaitanya Lala <clala@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e_config_collision_dist() sets tctl, but subsequently tctl is
overwritten. It seems to me that as things stand the call to
e1000e_config_collision_dist() has no effect and should either be
removed or moved down a little bit. This kernel patch takes the latter
option.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy corruption has been observed on 2-port 82571 adapters, and is root-caused
to lack of synchronization between the 2 driver instances, which conflict
when attempting to access the phy via the single MDIC register.
A semaphore exists for this purpose, and is now used on these designs. Because
PXE &/or EFI boot code (which we cannot expect to be built with this fix) may
leave the inter-instance semaphore in an invalid initial state when the driver
first loads, this fix also includes a one-time (per driver load) fix-up of the
semaphore initial state.
Signed-off-by: dave graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.
One to access nr_frags, one to access dma_maps[0]
Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.
Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With bi-directional stress traffic, the receiver could hang causing the
hardware to stop and a "Detected Tx Unit Hang" message dumped to the system
logfile. Temporarily workaround this issue by disabling Tx flow control by
default. The issue is currently being investigated and a follow-on patch
will be provided to revert this when it is resolved.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support for the next generation Intel desktop
and mobile gigabit ethernet LOM adapters. These adapters are the
follow-on parts to the LOMs tied to the prior ICH chipsets and are
comprised of a MAC in the PCH chipset and an external PHY (82577 for
mobile and 82578 for desktop versions). New features consist of PHY
wakeup to save power by completely turning off the MAC while in Sx
state, and 4K jumbo frames.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By putting the maximum frame size supported by the hardware into the
adapter structure, the change_mtu entry point function can be cleaned
up of checks for all the different max frame sizes supported by
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow control thresholds, i.e. high and low watermarks of the Rx
FIFO for when the hardware should transmit PAUSE frames (XON and XOFF,
respectively), need to be tuned for more efficient use of the FIFO.
The logic to set the thresholds for parts that support early-receive
(ERT) was also wrong in that it should check whether jumbo frames are
in use.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During reset, the driver was attempting to disable the Smart Powerdown
feature even if the part does not support Smart Powerdown. Check for
support before attempting to disable the feature.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CRC stripping should be enabled by default but was not if it was not
specified as a module parameter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy port status register has the MDI-X status bit on bit 11, not bit 3
as is currently setup in the define. This patch corrects that so the
correct bit is checked on igp PHY types.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after the recent changes to wired drivers to use only
netif_carrier_off the driver can have outstanding tx work to
complete that will never complete once link is down. Since the
intel hardware will hold this tx work forever, the driver
notices a tx timeout condition internally and might try
to instigate printk and reset of the part with a
netif_stop_queue, which doesn't work because link is down.
Don't bother arming to tx hang detection when link is down.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out that the Intel wired ethernet drivers do not need to
wake the tx queue since netif_carrier_on/off will take care of the qdisc
management in order to guarantee the correct handling of the transmit
routine enable state.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
Andy tested this for e1000e and confirmed it was working for him.
see thread: http://marc.info/?l=linux-netdev&m=123946479705636&w=2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andy Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the e1000e transmit cleanup inner loop exited early, then
cleaned might not be true. This could cause tx hangs or other
badness. Use count to track the total number of descriptors
cleaned instead of basing a tx queue restart off of a temporary
working state variable.
This code now makes the flow the same for e1000/e1000e/igb/ixgbe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent e1000e from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000e_shutdown() from e1000e_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000/e1000e compile report a possible unused variable, fix
that for now. Shortly after this a small refactor and bug
fix will follow in the same code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Alan Cox, it is possible for e1000e to exit its interrupt
handler or NAPI with interrupts enabled even when the driver is unloading or
being configured administratively down.
fix related to fix for: http://bugzilla.kernel.org/show_bug.cgi?id=12876
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e (and e1000, igb, ixgbe, ixgb) all do a series of operations each
time a multicast address is added. The flow goes something like
1) stack adds one multicast address
2) stack passes whole current list of unicast and multicast addresses to
driver
3) driver clears entire list in hardware
4) driver programs each multicast address using iomem in a loop
This was causing multicast packets to be lost during the reprogramming
process.
reference with test program:
http://kerneltrap.org/mailarchive/linux-netdev/2009/3/14/5160514/thread
Thanks to Dave Boutcher for his report and test program.
This driver fix prepares an array all at once in memory and programs it in
one shot to the hardware, not requiring an "erase" cycle. It would still
be possible for packets to be dropped while the receiver is off during
reprogramming.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Dave Boutcher <daveboutcher@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the e1000e tx cleanup routine to more closely match
what already exists in igb and e1000.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID for a new variant of the 82574 adapter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When merging into Jeff's tree:
commit 5f66f20806
Author: Arthur Jones <ajones@riverbed.com>
Date: Thu Mar 19 01:13:08 2009 +0000
e1000e: allow tx of pre-formatted vlan tagged packets
We lost one line, this fixes that missing
piece...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with igb, when the e1000e driver is fed 802.1q
packets with hardware checksum on, it chokes with an
error of the form:
checksum_partial proto=81!
As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.
There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out wiht the correct hardware checksum.
Thanks to Kand Ly <kand@riverbed.com> for discovering the
issue and the coming up with a solution. This patch is
based upon his work.
Fixups from Stephen Hemminger <shemminger@vyatta.com> and
Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a few issues I noticed in e1000e. These include a double free
of the skb if mapping fails, and the fact that context descriptors appear
to be left in the descriptor ring after the failure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID and related support for 82583 mac.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Radheka Godse <radheka.godse@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in reference to https://bugzilla.redhat.com/show_bug.cgi?id=484494
Also addresses issue show in kerneloops
The e1000e transmit code was calling pci_unmap_page on dma handles that it
might have called pci_map_single on.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the move of support for PCIe devices from e1000 to e1000e, this
workaround necessary only for older non-PCIe devices was mistakenly
copied into e1000e. Remove it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Make symbol static.
Fix this sparse warning:
drivers/net/e1000e/82571.c:1229:5: warning: symbol 'e1000_check_for_serdes_link_82571' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Single-thread access must be ensured for ICH8 NVM and PHY operations.
This synchronization is provided by the nvm_mutex. To assist in
understanding the contexts from which this code could be reached,
a WARN was output if the mutex was not going to be immediately
acquirable (if !mutex_trylock()). The code has now been optimized,
and we have verified that the few remaining mutex contentions are
reasonable and non-blocking, and it is time to remove the
mutex_trylock() and WARN messages.
Signed-off-by: dave graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses an issue where we did not restart auto-negotiation on
serdes links when the link partner was disabled and re-enabled. It includes
reworking the serdes link detect mechanism to be a state machine for
82571 and 82572 parts only.
Signed-off-by: dave graham <david.graham@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RXSEQ interrupts were used to force link state interrogation of serdes
links, as the Si was not guaranteed to report LSC interrupts when the
link changed state. On some bladeservers this resulted in false link up
reports if no link partner was connected. The RXSEQ treatment is
not necessary, as the link can be monitored from the watchdog timer, and
the false link indications cease.
Signed-off-by: dave graham <david.graham@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82571 and 82572 Errata #13 documents that the Si feature DMA Dynamic
Clock Gating should be disabled, and identifies the workaround of
disabling the feature by EEPROM setting. EEPROM versions that do not
include the recommended workaround have been found in the field, and so
some customers remain at risk. Because the feature DMA Dynamic clock
Gating can be disabled by directly setting the appropriate bit in the
E1000_CTRL_EXT register, this patch overrides the EEPROM setting, and
force-disables the feature.
Signed-off-by: dave graham <david.graham@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
most if not all of the devices supported by e1000e support
AER (Advanced Error Reporting) so we attempt to register
with the OS that we know how to reset ourselves after
a fatal error.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic change to use struct e1000_mac_info.serdes_has_link
consistently as the 'bool' that it's declared as.
No functional change.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Jeff Kirsher <Jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a hardware errata in some revisions of the 82574 that needs
to be worked around in the driver by setting a register bit at init.
If this bit is not set A0 versions of the 82574 can generate
tx hangs.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LLTX is deprecated and complicated, don't use it. It was observed by Don Ash
<donash4@gmail.com> that e1000e was acquiring this lock in the NAPI cleanup
path. This is obviously a bug, as this is a leftover from when e1000
supported multiple tx queues and fake netdevs.
another user reported this to us and tested routing with the 2.6.27 kernel and
this patch and reported a 3.5 % improvement in packets forwarded in a
multi-port test on 82571 parts.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that VLAN has GRO support as well, we can call its GRO handler
as well.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds process name of the current mutex holder to the WARN message output
when the e1000e driver attempts to acquire the nvm_mutex and finds that
it is already being held. With this patch the WARN message indicates
both the process name of the current mutex holder and the process name of
the attempted acquisition, which together will help to identify the
contending codepaths.
Signed-off-by: David Graham <david.graham@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device drivers that use pci_request_regions() (and similar APIs) have a
reasonable expectation that they are the only ones accessing their device.
As part of the e1000e hunt, we were afraid that some userland (X or some
bootsplash stuff) was mapping the MMIO region that the driver thought it
had exclusively via /dev/mem or via various sysfs resource mappings.
This patch adds the option for device drivers to cause their reserved
regions to the "banned from /dev/mem use" list, so now both kernel memory
and device-exclusive MMIO regions are banned.
NOTE: This is only active when CONFIG_STRICT_DEVMEM is set.
In addition to the config option, a kernel parameter iomem=relaxed is
provided for the cases where developers want to diagnose, in the field,
drivers issues from userspace.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix this sparse warnings:
drivers/net/e1000e/es2lan.c:1265:5: warning: symbol 'e1000_read_kmrn_reg_80003es2lan' was not declared. Should it be static?
drivers/net/e1000e/es2lan.c:1298:5: warning: symbol 'e1000_write_kmrn_reg_80003es2lan' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GRO support to e1000e by making it invoke napi_gro_receive
instead of netif_receive_skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a reset, releasing the swflag after it failed to be acquired would
cause a double unlock of the mutex. Instead, test whether acquisition of
the swflag was successful and if not, do not release the swflag. The reset
must still be done to bring the device to a quiescent state.
This resolves [BUG 12200] BUG: bad unlock balance detected! e1000e
http://bugzilla.kernel.org/show_bug.cgi?id=12200
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change interrupt vector naming to match recent changes from Robert Olsson.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant argument comments in files of drivers/net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return code for all NVM accesses[1] and error out accordingly; log
a debug message for failed accesses.
For ICH8/9, the valid NVM bank detect function was not checking whether the
SEC1VAL (sector 1 valid) bit in the EECD register was itself valid (bits 8
and 9 also have to be set). If invalid, it would have defaulted to the
possibly invalid bank 0. Instead, try to use the valid bank detection
method used by ICH10 which has been cleaned up a bit.
[1] - reads and updates only; not writes because those are only writing to
the Shadow RAM, the update following the write is the only thing actually
writing the modified Shadow RAM contents to the NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 82571 with SerDes, the true link state is not always correct when read
from the STATUS register; use existing e1000_has_link() function instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than reading the NVM to get the EEPROM version number everytime the
ethool get_drvinfo function is called, read it once during probe and save
it for future reference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing newline from debug message.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync flow control variables and usage model with that found in the ixgbe
driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ESB2, the MAC-to-PHY (Kumeran) interface must be configured after link
is up before any traffic is sent; a new PHY operations function pointer is
provided for this. To facilitate read/write of the Kumeran registers
without blocking PHY register writes, the driver/firmware synchronization
method which previously used a hardware semaphore for both PHY and Kumeran
register accesses is now split. New Kumeran register read/write functions
utilize this new synchronization method.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return of pci_save_state and error out accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some branding strings (displayed via lspci) are missing from the comments in
various family-specific files in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for link test does not work properly for 82571 parts in a blade
environment with an unterminated serdes link partner. Make the test more
robust by checking the invalid bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow the convention used elsewhere in e1000e to 'commit' PHY changes
instead of directly writing to the PHY CTRL register to reset it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been an issue seen with the pci-e quad port adapters that will
cause them to generate a pci-e correctable error on some system while
transitioning to D3.
Since no action is needed on this correctable error the simplest solution
is to mask off the reporting of correctable errors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change enables ECC correction for the packet buffer on all 82571
silicon.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users reported that they have machines with BMCs enabled that cannot
receive IPMI traffic after e1000e is loaded.
http://marc.info/?l=e1000-devel&m=121909039127414&w=2http://marc.info/?l=e1000-devel&m=121365543823387&w=2
This fixes the issue if they load with the new parameter = 0 by disabling
crc stripping, but leaves the performance feature on for most users.
Based on work done by Hong Zhang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver fails to initialize the first time due to the failure in the
phy_id check the kernel triggers a warn_on on the second try to load the
driver because the driver did not free the msi/x resources in the first
load because of the previous failure in phy_id check.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum. For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF. The
hardware takes care of this case but only if it is told the
packet is tcp.
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since e1000e has been existance in linux-2.6, we've
never released the hardware semaphore after a successful
write to the SPI EEPROM. I guess we don't write to
SPI EEPROM much -- but those few of us that do appreciate
it when we can later read from the EEPROM without having
to reboot.
Found-by: Nick Van Fossen <Nick.VanFossen@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Reviewed-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing 'WARN_ON(preempt_count())' was horribly horribly wrong, and would
cause tons of warnings at bootup if PREEMPT was enabled because the
initcalls currently run with the kernel lock, which increments the
preempt count.
At the same time, the warning was also insufficient, since it didn't
check that interrupts were enabled.
The proper debug function to use for something that can sleep and wants
a warning if it's called in the wrong context is 'might_sleep()'.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bruce Allan