compatible in dts has been changed, so the driver needs to be updated
accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Parameter offset_in_page in edac_mc_handle_ce() should mask the higher
bits above the page size, not the lower bits. The original input
sometimes causes a crash.
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Get rid of old users of of_platform_driver in arch/powerpc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In 5753c082f6 ("powerpc/85xx: Kconfig
cleanup") menuconfig MPC85xx was replaced by FSL_SOC_BOOKE but some
references insider the code were not adjusted accordingly. This patch
adresses these missing pieces.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
The MPC85xx EDAC driver is missing module device aliases, so the driver
won't load automatically on boot. This patch fixes the issue by adding
proper MODULE_DEVICE_TABLE() macros.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Dave Jiang <djiang@mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simply add a proper ID into the device table.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Dave Jiang <djiang@mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes build errors in EDAC drivers caused by the OF
device_node pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Use resource_size() instead of arithmetic.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the ability to detect the specific data line or ECC line which failed
when printing out SDRAM single-bit errors. An example of a single-bit
SDRAM ECC error is below:
EDAC MPC85xx MC1: Err Detect Register: 0x80000004
EDAC MPC85xx MC1: Faulty data bit: 59
EDAC MPC85xx MC1: Expected Data / ECC: 0x7f80d000_409effa0 / 0x6d
EDAC MPC85xx MC1: Captured Data / ECC: 0x7780d000_409effa0 / 0x6d
EDAC MPC85xx MC1: Err addr: 0x00031ca0
EDAC MPC85xx MC1: PFN: 0x00000031
Knowning which specific data or ECC line caused an error can be useful in
tracking down hardware issues such as improperly terminated signals, loose
pins, etc.
Note that this feature is only currently enabled for 64-bit wide data
buses, 32-bit wide bus support should be added.
I don't have any 32-bit wide systems to test on. If someone has one and
is willing to give this patch a shot with the check for a 64-bit data bus
removed it would be much appreciated and I can re-submit with both 32 and
64 bit buses supported.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With a 64-bit wide data bus only the lowest 8-bits of the ECC syndrome are
relevant. With a 32-bit wide data bus only the lowest 16-bits are
relevant on most architectures.
Without this change, the ECC syndrome displayed can be mildly confusing,
eg:
EDAC MPC85xx MC1: syndrome: 0x25252525
When in reality the ECC syndrome is 0x25.
A variety of Freescale manuals say a variety of different things about how
to decode the CAPTURE_ECC (syndrome) register. I don't have a system with
a 32-bit bus to test on, but I believe the change is correct. It'd be
good to get an ACK from someone at Freescale about this change though.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some unused, unsupported debug code existed in the mpc85xx EDAC driver
that resulted in a build failure when CONFIG_EDAC_DEBUG was defined:
drivers/edac/mpc85xx_edac.c: In function 'mpc85xx_mc_err_probe':
drivers/edac/mpc85xx_edac.c:1031: error: implicit declaration of function 'edac_mc_register_mcidev_debug'
drivers/edac/mpc85xx_edac.c:1031: error: 'debug_attr' undeclared (first use in this function)
drivers/edac/mpc85xx_edac.c:1031: error: (Each undeclared identifier is reported only once
drivers/edac/mpc85xx_edac.c:1031: error: for each function it appears in.)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b484625172 ("edac: mpc85xx add
mpc83xx support") accidentally broke how a chip select's first and last
page addresses are calculated. The page addresses are being shifted too
far right by PAGE_SHIFT. This results in errors such as:
EDAC MPC85xx MC1: Err addr: 0x003075c0
EDAC MPC85xx MC1: PFN: 0x00000307
EDAC MPC85xx MC1: PFN out of range!
EDAC MC1: INTERNAL ERROR: row out of range (4 >= 4)
EDAC MC1: CE - no information available: INTERNAL ERROR
The vaule of PAGE_SHIFT is already being taken into consideration during
the calculation of the 'start' and 'end' variables, thus it is not
necessary to account for it again when setting a chip select's first and
last page address.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When building without CONFIG_PCI the edac_pci_idx variable is unused,
causing a build-time warning. Wrap the variable in #ifdef CONFIG_PCI,
just like the rest of the PCI support.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Freescale MPC83xx memory controller to the existing
driver for the Freescale MPC85xx memory controller. The only difference
between the two processors are in the CS_BNDS register parsing code, which
has been changed so it will work on both processors.
The L2 cache controller does not exist on the MPC83xx, but the OF
subsystem will not use the driver if the device is not present in the OF
device tree.
I had to change the nr_pages calculation to make the math work out. I
checked it on my board and did the math by hand for a 64GB 85xx using 64K
pages. In both cases, nr_pages * PAGE_SIZE comes out to the correct
value.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on Kumar's new compatible types patch, add P2020 into MPC85xx EDAC
compatible lists so that EDAC can recognize P2020 meomry controller and L2
cache controller and export the relevant fields to sysfs.
EDAC MPC85xx DDR3 support is needed if DDR3 memory stick is installed on a
P2020DS board so that EDAC core can recognize DDR3 memory type.
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since some new MPC85xx SOCs support DDR3 memory now, so add DDR3 memory
type for MPC85xx EDAC.
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error found by Jeff Haran.
The error detect register is 0s when no errors are detected. The check
code is incorrect, so reverse check sense.
Reported-by: Jeff Haran <jharan@Brocade.COM>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All other compatibles that are uniquely identifying the processor use a
prefix of the form fsl,mpc85...'. We add support for it so we can
deprecate the older 'fsl,85...' that was improperly used here.
Additionally added mpc8536 & mpc8560 to the compatible lists.
This patch is based on Nate's 8572 patch.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for the dual-core MPC8572 processor. We have
to support making SPR changes on each core. Also, since we can
have multiple memory controllers sharing an interrupt, flag the
interrupts with IRQF_SHARED.
Signed-off-by: Andrew Kilkenny <akilkenny@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert PCI err device from platform to open firmware of_dev to comply
with powerpc schemes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
including of <asm/mpc85xx.h> causes build problems since it doesn't exist.
Also removed warning:
drivers/edac/mpc85xx_edac.c:45: warning: 'mpc85xx_ctl_name' defined but not used
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Made a previous global variable, static in scope
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shaohui Xie