In current situation host is adding the promiscuous QP to all steering
entries and the default entry as well. In this case when having PV
and SR-IOV on the same setup bridge will receive all traffic that is
targeted to the other VMs. This is bad.
Solution: In SR-IOV mode host can add promiscuous QP to default entry only.
The above problem and fix are relevant for B0 steering mode only.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In B0 steering mode when adding QPs to the default MCG entry need
to check that maximal number of QPs per MCG entry was not exceeded.
Signed-off-by: Alexander Guller <alexg@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make sure that the array index isn't used in the code with
negative value, we stop using the for loop integer iterator
outside of it.
>From now on use members count to swap the last QP with removed one.
Fix also the second occurrence of this flow in mlx4_qp_detach_common().
In mlx4_qp_detach_common() use members_count instead of
loop iterator outside of the for loop.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing multicast address in B0 steering mode there is
a bug in cases where there is a single QP registered for the address,
and this QP is also promiscuous. In such cases the entry wouldn't be
deleted from the SW structure representing all Ethernet MCG entries,
but would be removed in HW. This way when driver goes to remove it
from SW and HW structures the HW deletion fails.
Moreover the same index could later be used for registering
different address, which can be Infiniband.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instead of return error on zero rx_coalesce_usecs, disable coalesce
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a counter rx_noskb_drop for failure to allocate an skb.
Summed the per-channel rx_nodesc_trunc counters earlier so that they can
be included in rx_dropped.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of entries in the phy speed/duplex settings
array to support KR and KX mode, the work-around to add/remove
baseT settings to run at a fixed speed is no longer needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit enhances the iwarp driver to optionally keep a log of rdma
work request timining data for kernel mode QPs. If iw_cxgb4 module option
c4iw_wr_log is set to non-zero, each work request is tracked and timing
data maintained in a rolling log that is 4096 entries deep by default.
Module option c4iw_wr_log_size_order allows specifing a log2 size to use
instead of the default order of 12 (4096 entries). Both module options
are read-only and must be passed in at module load time to set them. IE:
modprobe iw_cxgb4 c4iw_wr_log=1 c4iw_wr_log_size_order=10
The timing data is viewable via the iw_cxgb4 debugfs file "wr_log".
Writing anything to this file will clear all the timing data.
Data tracked includes:
- The host time when the work request was posted, just before ringing
the doorbell. The host time when the completion was polled by the
application. This is also the time the log entry is created. The delta
of these two times is the amount of time took processing the work request.
- The qid of the EQ used to post the work request.
- The work request opcode.
- The cqe wr_id field. For sq completions requests this is the swsqe
index. For recv completions this is the MSN of the ingress SEND.
This value can be used to match log entries from this log with firmware
flowc event entries.
- The sge timestamp value just before ringing the doorbell when
posting, the sge timestamp value just after polling the completion,
and CQE.timestamp field from the completion itself. With these three
timestamps we can track the latency from post to poll, and the amount
of time the completion resided in the CQ before being reaped by the
application. With debug firmware, the sge timestamp is also logged by
firmware in its flowc history so that we can compute the latency from
posting the work request until the firmware sees it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ingress WRITE or READ RESPONSE errors, HW provides the offending
stag from the packet. This patch adds logic to log the parsed TPTE
in this case. cxgb4 now exports a function to read a TPTE entry
from adapter memory.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise a larger max read queue depth for qps, and gather the resource limits
from fw and use them to avoid exhaustinq all the resources.
Design:
cxgb4:
Obtain the max_ordird_qp and max_ird_adapter device params from FW
at init time and pass them up to the ULDs when they attach. If these
parameters are not available, due to older firmware, then hard-code
the values based on the known values for older firmware.
iw_cxgb4:
Fix the c4iw_query_device() to report these correct values based on
adapter parameters. ibv_query_device() will always return:
max_qp_rd_atom = max_qp_init_rd_atom = min(module_max, max_ordird_qp)
max_res_rd_atom = max_ird_adapter
Bump up the per qp max module option to 32, allowing it to be increased
by the user up to the device max of max_ordird_qp. 32 seems to be
sufficient to maximize throughput for streaming read benchmarks.
Fail connection setup if the negotiated IRD exhausts the available
adapter ird resources. So the driver will track the amount of ird
resource in use and not send an RI_WR/INIT to FW that would reduce the
available ird resources below zero.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates iw_cxgb4 to determine the Ingress Padding Boundary from
cxgb4_lld_info, and take subsequent actions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The proper string for this license is "GPL v2", instead of "GPLv2".
This commit fixes that.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the 'foo*' bar with 'foo *bar' and (foo*) with (foo *).
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally any device ids will be above the corresponding device driver
structure. This patch moves the pci device ids and MODULE_DEVICE_TABLE()
above the pci driver structure.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert printk() to netdev_dbg/info/err or dev_info/err/dbg
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace ioremap() with the devm_ioremap() so that
the resource will be freed automatically with the probe failed.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the remove functionalities after the probe
so that we can see the registered and released resources properly.
Every driver follows the same concept.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to select 40G mode on a 10G/40G capable card.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Napi id was not marked for gro_skb, this will lead rx busy loop won't
work correctly since they stack never try to call low latency receive
method because of a zero socket napi id. Fix this by marking napi id
for gro_skb.
The transaction rate of 1 byte netperf tcp_rr gets about 50% increased
(from 20531.68 to 30610.88).
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_MODE_EN bit was defined to 0, while it is actually 6. It was not
much of a problem on older designs where this was a no-op, and the RGMII
data-path would always be enabled, but newer GENET controllers need to
explicitely enable their RGMII data-pad using this bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first
time it is armed, ocassionally we have observed that the EQ doesn't raise
anymore interrupts even if it is in armed state.
This patch fixes this by setting the clear-interrupt bit when EQs are
armed for the first time in be_open().
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the IPv6 hw checksum for RTL8111C and later chips. Note
that the hw has the limitation for the transport offset. The
checksum must be calculated by sw, when the transport offset is
out of the range which the hw accepts.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace large send with giant send for TSO for RTL8111C and later ICs.
The large send setting of the RTL8111DP is different from the other
chips. However, the giant send setting is the same for all the chips
which support it. Use the giant send to synchronize the settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the txd_version, split rtl8169_tso_csum() into
rtl8169_tso_csum_v1() and rtl8169_tso_csum_v2().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a new network driver for the network controller in Marvell
Armada 375 SoC.
Given the controller is very different from the ones in the other Marvell
SoCs that use the mv643xx_eth (Kirkwood, Orion, Discovery) and mvneta
(Armada 370/38x/XP) drivers, a new driver is needed.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
[Ezequiel: coding style cleanup]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the debug message format. This patch changes to the
commit f160a2d0b524eeebd97a68e2fbb59fad4cdd3fee: net: cpmac: dynamic debug fixes
When we use pr_debug()/netdev_dbg() new lines are inserting in b/w
the values. The format when i use the printk()
These formats used in skb dump and reg dump. This functions
called from the entire code. So this will be enabled all the lines.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping a bridge fdb dumps every fdb entry
held. With this change we are going to filter
on selected bridge port.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some devices, the internal PLL circuit occasionally provides the
wrong clock frequency after power up. The probability of failure is less
than one failure per 1000 power cycles. When the failure occurs, the
internal clock frequency is around 1/20 of the correct frequency.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
before registering the the net device this code freeing net device
by using the label 'fail'
fixed by introducing an another label 'out'
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch insert proper spaces before return statement.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes to style of declarattion which follows every driver
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does the following changes
1. convert printk(KERN_DEBUG.. to netdev_dbg() if we have net_device object
or convert to dev_dbg() if we have device object.
2. convert printk(KERN_WARNING.. to netdev_warn() if we have net_device object
or convert to dev_warn() if we have device object
3. convert printk() to pr_*
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert the normal comments to networking subsystem
style comments.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the space after '#' in macro defination
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged two uses of kzalloc() for allocating and zeroing
arrays, use kcalloc() instead as recommended.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged a bunch of: "CHECK: Alignment should match open
parenthesis" problems, fix all of them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer to the struct net_device in the private data is only
assigned but never used, so delete it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
arc_emac_priv, use stats from struct net_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8411, RTL8111G, RTL8402, RTL8105, and RTL8106, disable the feature
of entering the L2/L3 link state of the PCIe. When the nic starts the process
of entering the L2/L3 link state and the PCI reset occurs before the work
is finished, the work would be queued and continue after the next the PCI
reset occurs. This causes the device stays in L2/L3 link state, and the system
couldn't find the device.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugenia Emantayev